Drop support for ipq806x for kernel 6.1.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-# CONFIG_APQ_GCC_8084 is not set
-# CONFIG_APQ_MMCC_8084 is not set
-CONFIG_ARCH_32BIT_OFF_T=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-# CONFIG_ARCH_IPQ40XX is not set
-CONFIG_ARCH_KEEP_MEMBLOCK=y
-# CONFIG_ARCH_MDM9615 is not set
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-# CONFIG_ARCH_MSM8909 is not set
-# CONFIG_ARCH_MSM8916 is not set
-CONFIG_ARCH_MSM8960=y
-CONFIG_ARCH_MSM8974=y
-CONFIG_ARCH_MSM8X60=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_V6_V7=y
-CONFIG_ARCH_MULTI_V7=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
-CONFIG_ARCH_QCOM=y
-CONFIG_ARCH_SELECT_MEMORY_MODEL=y
-CONFIG_ARCH_SPARSEMEM_ENABLE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ARCH_TIMER=y
-CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER is not set
-CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE=y
-CONFIG_ARM_ATAG_DTB_COMPAT_IGNORE_MEM=y
-CONFIG_ARM_CPUIDLE=y
-CONFIG_ARM_CPU_SUSPEND=y
-# CONFIG_ARM_CPU_TOPOLOGY is not set
-CONFIG_ARM_GIC=y
-CONFIG_ARM_HAS_GROUP_RELOCS=y
-CONFIG_ARM_IPQ806X_FAB_DEVFREQ=y
-CONFIG_ARM_KRAIT_CACHE_DEVFREQ=y
-CONFIG_ARM_L1_CACHE_SHIFT=6
-CONFIG_ARM_L1_CACHE_SHIFT_6=y
-CONFIG_ARM_PATCH_IDIV=y
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_QCOM_CPUFREQ_HW is not set
-CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y
-CONFIG_ARM_QCOM_SPM_CPUIDLE=y
-# CONFIG_ARM_SMMU is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_UNWIND=y
-CONFIG_ARM_VIRT_EXT=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_MQ_PCI=y
-CONFIG_BOUNCE=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_HAVE_STACKPROTECTOR_TLS=y
-CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5"
-CONFIG_CC_NO_ARRAY_BOUNDS=y
-CONFIG_CLKSRC_QCOM=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE_OVERRIDE=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMMON_CLK_QCOM=y
-CONFIG_COMPACT_UNEVICTABLE_DEFAULT=1
-CONFIG_COMPAT_32BIT_TIME=y
-CONFIG_CONTEXT_TRACKING=y
-CONFIG_CONTEXT_TRACKING_IDLE=y
-CONFIG_CPUFREQ_DT=y
-CONFIG_CPUFREQ_DT_PLATDEV=y
-CONFIG_CPU_32v6K=y
-CONFIG_CPU_32v7=y
-CONFIG_CPU_ABRT_EV7=y
-CONFIG_CPU_CACHE_V7=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_ATTR_SET=y
-CONFIG_CPU_FREQ_GOV_COMMON=y
-# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
-CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
-# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
-CONFIG_CPU_FREQ_STAT=y
-CONFIG_CPU_HAS_ASID=y
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_IDLE_GOV_MENU=y
-CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-CONFIG_CPU_PABRT_V7=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_SPECTRE=y
-CONFIG_CPU_THERMAL=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_V7=y
-CONFIG_CPU_V7=y
-CONFIG_CRC16=y
-# CONFIG_CRC32_SARWATE is not set
-CONFIG_CRC32_SLICEBY8=y
-CONFIG_CRC8=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_DEV_QCOM_RNG=y
-CONFIG_CRYPTO_DRBG=y
-CONFIG_CRYPTO_DRBG_HMAC=y
-CONFIG_CRYPTO_DRBG_MENU=y
-CONFIG_CRYPTO_HASH_INFO=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_JITTERENTROPY=y
-CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
-CONFIG_CRYPTO_LIB_SHA1=y
-CONFIG_CRYPTO_LIB_SHA256=y
-CONFIG_CRYPTO_LIB_UTILS=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_SHA256=y
-CONFIG_CRYPTO_SHA512=y
-CONFIG_CRYPTO_ZSTD=y
-CONFIG_CURRENT_POINTER_IN_TPIDRURO=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_GPIO=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-CONFIG_DEVFREQ_GOV_PASSIVE=y
-# CONFIG_DEVFREQ_GOV_PERFORMANCE is not set
-# CONFIG_DEVFREQ_GOV_POWERSAVE is not set
-# CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND is not set
-# CONFIG_DEVFREQ_GOV_USERSPACE is not set
-# CONFIG_DEVFREQ_THERMAL is not set
-CONFIG_DMADEVICES=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_OF=y
-CONFIG_DMA_OPS=y
-CONFIG_DMA_VIRTUAL_CHANNELS=y
-CONFIG_DTC=y
-CONFIG_DT_IDLE_STATES=y
-# CONFIG_DWMAC_GENERIC is not set
-CONFIG_DWMAC_IPQ806X=y
-# CONFIG_DWMAC_QCOM_ETHQOS is not set
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_EXCLUSIVE_SYSTEM_RAM=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FWNODE_MDIO=y
-CONFIG_FW_LOADER_PAGED_BUF=y
-CONFIG_FW_LOADER_SYSFS=y
-CONFIG_GCC11_NO_ARRAY_BOUNDS=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_CPU_VULNERABILITIES=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_GETTIMEOFDAY=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
-CONFIG_GENERIC_IRQ_MIGRATION=y
-CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y
-CONFIG_GENERIC_MSI_IRQ=y
-CONFIG_GENERIC_MSI_IRQ_DOMAIN=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_PINCTRL_GROUPS=y
-CONFIG_GENERIC_PINMUX_FUNCTIONS=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GENERIC_TIME_VSYSCALL=y
-CONFIG_GENERIC_VDSO_32=y
-CONFIG_GLOB=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_CDEV=y
-CONFIG_GRO_CELLS=y
-CONFIG_HARDEN_BRANCH_PREDICTOR=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HAVE_SMP=y
-CONFIG_HIGHMEM=y
-# CONFIG_HIGHPTE is not set
-CONFIG_HOTPLUG_CPU=y
-CONFIG_HWMON=y
-CONFIG_HWSPINLOCK=y
-CONFIG_HWSPINLOCK_QCOM=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ_FIXED=0
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_HELPER_AUTO=y
-# CONFIG_I2C_QCOM_CCI is not set
-CONFIG_I2C_QUP=y
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_IOMMU_DEBUGFS is not set
-# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set
-# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set
-CONFIG_IOMMU_SUPPORT=y
-# CONFIG_IPQ_APSS_PLL is not set
-# CONFIG_IPQ_GCC_4019 is not set
-# CONFIG_IPQ_GCC_6018 is not set
-CONFIG_IPQ_GCC_806X=y
-# CONFIG_IPQ_GCC_8074 is not set
-# CONFIG_IPQ_LCC_806X is not set
-CONFIG_IRQCHIP=y
-CONFIG_IRQSTACKS=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_DOMAIN_HIERARCHY=y
-CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_KMAP_LOCAL=y
-CONFIG_KMAP_LOCAL_NON_LINEAR_PTE_ARRAY=y
-CONFIG_KPSS_XCC=y
-CONFIG_KRAITCC=y
-CONFIG_KRAIT_CLOCKS=y
-CONFIG_KRAIT_L2_ACCESSORS=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_DEBUGGING_SUPPORT=y
-CONFIG_LOCK_SPIN_ON_OWNER=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MDIO_BITBANG=y
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MDIO_DEVRES=y
-CONFIG_MDIO_GPIO=y
-CONFIG_MDIO_IPQ8064=y
-# CONFIG_MDM_GCC_9615 is not set
-# CONFIG_MDM_LCC_9615 is not set
-CONFIG_MEMFD_CREATE=y
-# CONFIG_MFD_HI6421_SPMI is not set
-CONFIG_MFD_QCOM_RPM=y
-# CONFIG_MFD_SPMI_PMIC is not set
-CONFIG_MFD_SYSCON=y
-CONFIG_MIGHT_HAVE_CACHE_L2X0=y
-CONFIG_MIGRATION=y
-CONFIG_MMC=y
-CONFIG_MMC_ARMMMCI=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_BLOCK_MINORS=16
-CONFIG_MMC_CQHCI=y
-CONFIG_MMC_QCOM_DML=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_IO_ACCESSORS=y
-CONFIG_MMC_SDHCI_MSM=y
-# CONFIG_MMC_SDHCI_PCI is not set
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MSM_GCC_8660=y
-# CONFIG_MSM_GCC_8909 is not set
-# CONFIG_MSM_GCC_8916 is not set
-# CONFIG_MSM_GCC_8939 is not set
-# CONFIG_MSM_GCC_8960 is not set
-# CONFIG_MSM_GCC_8974 is not set
-# CONFIG_MSM_GCC_8976 is not set
-# CONFIG_MSM_GCC_8994 is not set
-# CONFIG_MSM_GCC_8996 is not set
-# CONFIG_MSM_GCC_8998 is not set
-# CONFIG_MSM_GPUCC_8998 is not set
-# CONFIG_MSM_IOMMU is not set
-# CONFIG_MSM_LCC_8960 is not set
-# CONFIG_MSM_MMCC_8960 is not set
-# CONFIG_MSM_MMCC_8974 is not set
-# CONFIG_MSM_MMCC_8996 is not set
-# CONFIG_MSM_MMCC_8998 is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND_CORE=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_ECC_SW_HAMMING=y
-CONFIG_MTD_NAND_QCOM=y
-CONFIG_MTD_QCOMSMEM_PARTS=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_SPLIT_FIRMWARE=y
-CONFIG_MTD_SPLIT_FIT_FW=y
-CONFIG_MTD_SPLIT_UIMAGE_FW=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MUTEX_SPIN_ON_OWNER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEON=y
-CONFIG_NET_DEVLINK=y
-CONFIG_NET_DSA=y
-CONFIG_NET_DSA_QCA8K=y
-CONFIG_NET_DSA_QCA8K_LEDS_SUPPORT=y
-CONFIG_NET_DSA_TAG_QCA=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NET_PTP_CLASSIFY=y
-CONFIG_NET_SELFTESTS=y
-CONFIG_NET_SWITCHDEV=y
-CONFIG_NLS=y
-CONFIG_NO_HZ=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_NR_CPUS=2
-CONFIG_NVMEM=y
-CONFIG_NVMEM_LAYOUTS=y
-CONFIG_NVMEM_QCOM_QFPROM=y
-# CONFIG_NVMEM_QCOM_SEC_QFPROM is not set
-# CONFIG_NVMEM_SPMI_SDAM is not set
-CONFIG_NVMEM_SYSFS=y
-CONFIG_NVMEM_U_BOOT_ENV=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_KOBJ=y
-CONFIG_OF_MDIO=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PADATA=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PAGE_POOL=y
-CONFIG_PAGE_SIZE_LESS_THAN_256KB=y
-CONFIG_PAGE_SIZE_LESS_THAN_64KB=y
-CONFIG_PAHOLE_HAS_LANG_EXCLUDE=y
-CONFIG_PCI=y
-CONFIG_PCIEAER=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCIE_DW=y
-CONFIG_PCIE_DW_HOST=y
-CONFIG_PCIE_QCOM=y
-CONFIG_PCI_DEBUG=y
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PCI_MSI=y
-CONFIG_PCI_MSI_IRQ_DOMAIN=y
-CONFIG_PCS_XPCS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_LEDS=y
-CONFIG_PHYLINK=y
-# CONFIG_PHY_QCOM_APQ8064_SATA is not set
-# CONFIG_PHY_QCOM_EDP is not set
-# CONFIG_PHY_QCOM_IPQ4019_USB is not set
-CONFIG_PHY_QCOM_IPQ806X_SATA=y
-# CONFIG_PHY_QCOM_IPQ806X_USB is not set
-# CONFIG_PHY_QCOM_PCIE2 is not set
-# CONFIG_PHY_QCOM_QMP is not set
-# CONFIG_PHY_QCOM_QUSB2 is not set
-# CONFIG_PHY_QCOM_USB_HS_28NM is not set
-# CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2 is not set
-# CONFIG_PHY_QCOM_USB_SS is not set
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_APQ8064 is not set
-# CONFIG_PINCTRL_APQ8084 is not set
-# CONFIG_PINCTRL_IPQ4019 is not set
-CONFIG_PINCTRL_IPQ8064=y
-# CONFIG_PINCTRL_MDM9615 is not set
-CONFIG_PINCTRL_MSM=y
-# CONFIG_PINCTRL_MSM8226 is not set
-# CONFIG_PINCTRL_MSM8660 is not set
-# CONFIG_PINCTRL_MSM8909 is not set
-# CONFIG_PINCTRL_MSM8916 is not set
-# CONFIG_PINCTRL_MSM8960 is not set
-# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set
-# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set
-# CONFIG_PINCTRL_SDX65 is not set
-CONFIG_PM_DEVFREQ=y
-# CONFIG_PM_DEVFREQ_EVENT is not set
-CONFIG_PM_OPP=y
-CONFIG_POWER_RESET=y
-CONFIG_POWER_RESET_MSM=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PPS=y
-CONFIG_PREEMPT_NONE_BUILD=y
-CONFIG_PRINTK_TIME=y
-CONFIG_PTP_1588_CLOCK=y
-CONFIG_PTP_1588_CLOCK_OPTIONAL=y
-CONFIG_QCA83XX_PHY=y
-# CONFIG_QCM_DISPCC_2290 is not set
-# CONFIG_QCM_GCC_2290 is not set
-# CONFIG_QCOM_A53PLL is not set
-CONFIG_QCOM_ADM=y
-CONFIG_QCOM_BAM_DMA=y
-CONFIG_QCOM_CLK_RPM=y
-# CONFIG_QCOM_COMMAND_DB is not set
-# CONFIG_QCOM_CPR is not set
-# CONFIG_QCOM_EBI2 is not set
-# CONFIG_QCOM_GENI_SE is not set
-CONFIG_QCOM_GSBI=y
-CONFIG_QCOM_HFPLL=y
-# CONFIG_QCOM_ICC_BWMON is not set
-# CONFIG_QCOM_IOMMU is not set
-# CONFIG_QCOM_LLCC is not set
-CONFIG_QCOM_NET_PHYLIB=y
-# CONFIG_QCOM_OCMEM is not set
-# CONFIG_QCOM_PDC is not set
-# CONFIG_QCOM_RMTFS_MEM is not set
-CONFIG_QCOM_RPMCC=y
-# CONFIG_QCOM_RPMH is not set
-CONFIG_QCOM_SCM=y
-# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set
-CONFIG_QCOM_SMEM=y
-# CONFIG_QCOM_SMSM is not set
-CONFIG_QCOM_SOCINFO=y
-CONFIG_QCOM_SPM=y
-# CONFIG_QCOM_STATS is not set
-CONFIG_QCOM_TCSR=y
-CONFIG_QCOM_TSENS=y
-CONFIG_QCOM_WDT=y
-# CONFIG_QCS_GCC_404 is not set
-# CONFIG_QCS_Q6SSTOP_404 is not set
-# CONFIG_QCS_TURING_404 is not set
-CONFIG_RANDSTRUCT_NONE=y
-CONFIG_RAS=y
-CONFIG_RATIONAL=y
-CONFIG_RCU_CPU_STALL_TIMEOUT=21
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-# CONFIG_REGULATOR_QCOM_LABIBB is not set
-CONFIG_REGULATOR_QCOM_RPM=y
-# CONFIG_REGULATOR_QCOM_SPMI is not set
-# CONFIG_REGULATOR_QCOM_USB_VBUS is not set
-# CONFIG_REGULATOR_VQMMC_IPQ4019 is not set
-CONFIG_RESET_CONTROLLER=y
-# CONFIG_RESET_QCOM_AOSS is not set
-# CONFIG_RESET_QCOM_PDC is not set
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_I2C_AND_SPI=y
-CONFIG_RTC_MC146818_LIB=y
-CONFIG_RWSEM_SPIN_ON_OWNER=y
-# CONFIG_SC_CAMCC_7280 is not set
-# CONFIG_SC_DISPCC_7180 is not set
-# CONFIG_SC_GCC_7180 is not set
-# CONFIG_SC_GCC_8280XP is not set
-# CONFIG_SC_GPUCC_7180 is not set
-# CONFIG_SC_LPASSCC_7280 is not set
-# CONFIG_SC_LPASS_CORECC_7180 is not set
-# CONFIG_SC_LPASS_CORECC_7280 is not set
-# CONFIG_SC_MSS_7180 is not set
-# CONFIG_SC_VIDEOCC_7180 is not set
-# CONFIG_SDM_CAMCC_845 is not set
-# CONFIG_SDM_DISPCC_845 is not set
-# CONFIG_SDM_GCC_660 is not set
-# CONFIG_SDM_GCC_845 is not set
-# CONFIG_SDM_GPUCC_845 is not set
-# CONFIG_SDM_LPASSCC_845 is not set
-# CONFIG_SDM_VIDEOCC_845 is not set
-# CONFIG_SDX_GCC_65 is not set
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_MCTRL_GPIO=y
-CONFIG_SERIAL_MSM=y
-CONFIG_SERIAL_MSM_CONSOLE=y
-CONFIG_SGL_ALLOC=y
-CONFIG_SMP=y
-CONFIG_SMP_ON_UP=y
-# CONFIG_SM_CAMCC_8450 is not set
-# CONFIG_SM_GCC_8150 is not set
-# CONFIG_SM_GCC_8250 is not set
-# CONFIG_SM_GCC_8450 is not set
-# CONFIG_SM_GPUCC_6350 is not set
-# CONFIG_SM_GPUCC_8150 is not set
-# CONFIG_SM_GPUCC_8250 is not set
-# CONFIG_SM_GPUCC_8350 is not set
-# CONFIG_SM_VIDEOCC_8150 is not set
-# CONFIG_SM_VIDEOCC_8250 is not set
-CONFIG_SOCK_RX_QUEUE_MAPPING=y
-CONFIG_SOC_BUS=y
-CONFIG_SOFTIRQ_ON_OWN_STACK=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPI_MEM=y
-CONFIG_SPI_QUP=y
-CONFIG_SPMI=y
-# CONFIG_SPMI_HISI3670 is not set
-CONFIG_SPMI_MSM_PMIC_ARB=y
-# CONFIG_SPMI_PMIC_CLKDIV is not set
-CONFIG_SRCU=y
-CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_PLATFORM=y
-CONFIG_SWPHY=y
-CONFIG_SWP_EMULATE=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_OF=y
-CONFIG_THREAD_INFO_IN_TASK=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TREE_RCU=y
-CONFIG_TREE_SRCU=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-# CONFIG_UCLAMP_TASK is not set
-CONFIG_UEVENT_HELPER_PATH=""
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_UNWINDER_ARM=y
-CONFIG_USB=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-CONFIG_VFP=y
-CONFIG_VFPv3=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XPS=y
-CONFIG_XXHASH=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0
-CONFIG_ZBOOT_ROM_TEXT=0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZSTD_COMMON=y
-CONFIG_ZSTD_COMPRESS=y
-CONFIG_ZSTD_DECOMPRESS=y
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8062-smb208.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "NEC Platforms Aterm WG2600HP3";
- compatible = "nec,wg2600hp3", "qcom,ipq8062", "qcom,ipq8064";
-
- memory {
- device_type = "memory";
- reg = <0x42000000 0x1e000000>;
- };
-
- aliases {
- label-mac-device = &gmac2;
-
- led-boot = &led_power_green;
- led-failsafe = &led_power_red;
- led-running = &led_power_green;
- led-upgrade = &led_power_red;
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&buttons_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- mode0 {
- label = "mode0";
- gpios = <&qcom_pinmux 40 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_0>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- mode1 {
- label = "mode1";
- gpios = <&qcom_pinmux 41 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_1>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- pinctrl-0 = <&leds_pins>;
- pinctrl-names = "default";
-
- led_power_green: power_green {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
- };
-
- led_power_red: power_red {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&qcom_pinmux 35 GPIO_ACTIVE_HIGH>;
- };
-
- active_green {
- label = "green:active";
- gpios = <&qcom_pinmux 42 GPIO_ACTIVE_HIGH>;
- };
-
- active_red {
- label = "red:active";
- gpios = <&qcom_pinmux 38 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g_green {
- label = "green:wlan2g";
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy1tpt";
- };
-
- wlan2g_red {
- label = "red:wlan2g";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g_green {
- label = "green:wlan5g";
- gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tpt";
- };
-
- wlan5g_red {
- label = "red:wlan5g";
- gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>;
- };
-
- tv_green {
- label = "green:tv";
- gpios = <&qcom_pinmux 46 GPIO_ACTIVE_HIGH>;
- };
-
- tv_red {
- label = "red:tv";
- gpios = <&qcom_pinmux 36 GPIO_ACTIVE_HIGH>;
- };
-
- converter_green {
- label = "green:converter";
- gpios = <&qcom_pinmux 43 GPIO_ACTIVE_HIGH>;
- };
-
- converter_red {
- label = "red:converter";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-/* nand_pins are used for leds_pins, empty the node
- * from ipq8064.dtsi
- */
-&nand_pins {
- /delete-property/ disable;
- /delete-property/ pullups;
- /delete-property/ hold;
-};
-
-&qcom_pinmux {
- pinctrl-0 = <&akro_pins>;
- pinctrl-names = "default";
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- buttons_pins: buttons_pins {
- mux {
- pins = "gpio22", "gpio24", "gpio40",
- "gpio41";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- leds_pins: leds_pins {
- mux {
- pins = "gpio14", "gpio15", "gpio35",
- "gpio36", "gpio38", "gpio42",
- "gpio43", "gpio46", "gpio55",
- "gpio56", "gpio57", "gpio58";
- function = "gpio";
- bias-pull-down;
- };
-
- akro2 {
- pins = "gpio15", "gpio35", "gpio38",
- "gpio42", "gpio43", "gpio46",
- "gpio55", "gpio56", "gpio57",
- "gpio58";
- drive-strength = <2>;
- };
-
- akro4 {
- pins = "gpio14", "gpio36";
- drive-strength = <4>;
- };
- };
-
- /*
- * Stock firmware has the following settings, so let's do the same.
- * I don't sure why these are required.
- */
- akro_pins: akro_pinmux {
- akro {
- pins = "gpio17", "gpio26", "gpio47";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
-
- reset {
- pins = "gpio45";
- function = "gpio";
- drive-strength = <2>;
- bias-disable;
- output-low;
- };
-
- gmac0_rgmii {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-};
-
-&gsbi5 {
- status = "okay";
- qcom,mode = <GSBI_PROT_SPI>;
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <50000000>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0000000 0x0020000>;
- read-only;
- };
-
- partition@20000 {
- label = "MIBIB";
- reg = <0x0020000 0x0020000>;
- read-only;
- };
-
- partition@40000 {
- label = "SBL2";
- reg = <0x0040000 0x0040000>;
- read-only;
- };
-
- partition@80000 {
- label = "SBL3";
- reg = <0x0080000 0x0080000>;
- read-only;
- };
-
- partition@100000 {
- label = "DDRCONFIG";
- reg = <0x0100000 0x0010000>;
- read-only;
- };
-
- partition@110000 {
- label = "SSD";
- reg = <0x0110000 0x0010000>;
- read-only;
- };
-
- partition@120000 {
- label = "TZ";
- reg = <0x0120000 0x0080000>;
- read-only;
- };
-
- partition@1a0000 {
- label = "RPM";
- reg = <0x01a0000 0x0080000>;
- read-only;
- };
-
- partition@220000 {
- label = "APPSBL";
- reg = <0x0220000 0x0080000>;
- read-only;
- };
-
- partition@2a0000 {
- label = "APPSBLENV";
- reg = <0x02a0000 0x0010000>;
- read-only;
- };
-
- factory: partition@2b0000 {
- label = "PRODUCTDATA";
- reg = <0x02b0000 0x0030000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_factory_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_factory_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
-
- macaddr_PRODUCTDATA_c: macaddr@c {
- reg = <0xc 0x6>;
- };
-
- macaddr_PRODUCTDATA_12: macaddr@12 {
- reg = <0x12 0x6>;
- };
- };
- };
-
- partition@2e0000 {
- label = "ART";
- reg = <0x02e0000 0x0040000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- partition@320000 {
- label = "TP";
- reg = <0x0320000 0x0040000>;
- read-only;
- };
-
- partition@360000 {
- label = "TINY";
- reg = <0x0360000 0x0500000>;
- read-only;
- };
-
- partition@860000 {
- compatible = "denx,uimage";
- label = "firmware";
- reg = <0x0860000 0x17a0000>;
- };
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- reg = <0x00010000 0 0 0 0>;
-
- qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3";
-
- nvmem-cells = <&macaddr_PRODUCTDATA_12>, <&precal_ART_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- force_gen1 = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- reg = <0x00010000 0 0 0 0>;
-
- ieee80211-freq-limit = <2400000 2483000>;
- qcom,ath10k-calibration-variant = "NEC-Platforms-WG2600HP3";
-
- nvmem-cells = <&macaddr_PRODUCTDATA_c>, <&precal_ART_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_WAN;
- function-enumerator = <1>;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_WAN;
- function-enumerator = <2>;
- default-state = "keep";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_WAN;
- function-enumerator = <3>;
- default-state = "keep";
- };
- };
- };
-
- port@2 {
- reg = <2>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <1>;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <2>;
- default-state = "keep";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <3>;
- default-state = "keep";
- };
- };
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <1>;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <2>;
- default-state = "keep";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <3>;
- default-state = "keep";
- };
- };
- };
-
- port@4 {
- reg = <4>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <1>;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <2>;
- default-state = "keep";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <3>;
- default-state = "keep";
- };
- };
- };
-
- port@5 {
- reg = <5>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <1>;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <2>;
- default-state = "keep";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- function-enumerator = <3>;
- default-state = "keep";
- };
- };
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
- qca,sgmii-rxclk-falling-edge;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
- mdiobus = <&mdio0>;
- nvmem-cells = <&macaddr_factory_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- mdiobus = <&mdio0>;
- nvmem-cells = <&macaddr_factory_6>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- ramoops@42100000 {
- compatible = "ramoops";
- reg = <0x42100000 0x40000>;
- record-size = <0x4000>;
- console-size = <0x4000>;
- ftrace-size = <0x4000>;
- pmsg-size = <0x4000>;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
- label-mac-device = &gmac2;
- };
-};
-
-&qcom_pinmux {
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- usb0_pwr_en_pin: usb0_pwr_en_pin {
- mux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
-
- usb1_pwr_en_pin: usb1_pwr_en_pin {
- mux {
- pins = "gpio23";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- partition@40000 {
- label = "SBL2";
- reg = <0x40000 0x20000>;
- read-only;
- };
-
- partition@60000 {
- label = "SBL3";
- reg = <0x60000 0x30000>;
- read-only;
- };
-
- partition@90000 {
- label = "DDRCONFIG";
- reg = <0x90000 0x10000>;
- read-only;
- };
-
- partition@a0000 {
- label = "SSD";
- reg = <0xa0000 0x10000>;
- read-only;
- };
-
- partition@b0000 {
- label = "TZ";
- reg = <0xb0000 0x30000>;
- read-only;
- };
-
- partition@e0000 {
- label = "RPM";
- reg = <0xe0000 0x20000>;
- read-only;
- };
-
- partition@100000 {
- label = "fs-uboot";
- reg = <0x100000 0x70000>;
- read-only;
- };
-
- partition@170000 {
- label = "uboot-env";
- reg = <0x170000 0x40000>;
- read-only;
- };
-
- partition@1b0000 {
- label = "radio";
- reg = <0x1b0000 0x40000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_radio_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_radio_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- partition@1f0000 {
- label = "os-image";
- reg = <0x1f0000 0x400000>;
- };
-
- partition@5f0000 {
- label = "rootfs";
- reg = <0x5f0000 0x1900000>;
- };
-
- defaultmac: partition@1ef0000 {
- label = "default-mac";
- reg = <0x1ef0000 0x00200>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_defaultmac_8: macaddr@8 {
- compatible = "mac-base";
- reg = <0x8 0x6>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-
- partition@1ef0200 {
- label = "pin";
- reg = <0x1ef0200 0x00200>;
- read-only;
- };
-
- partition@1ef0400 {
- label = "product-info";
- reg = <0x1ef0400 0x0fc00>;
- read-only;
- };
-
- partition@1f00000 {
- label = "partition-table";
- reg = <0x1f00000 0x10000>;
- read-only;
- };
-
- partition@1f10000 {
- label = "soft-version";
- reg = <0x1f10000 0x10000>;
- read-only;
- };
-
- partition@1f20000 {
- label = "support-list";
- reg = <0x1f20000 0x10000>;
- read-only;
- };
-
- partition@1f30000 {
- label = "profile";
- reg = <0x1f30000 0x10000>;
- read-only;
- };
-
- partition@1f40000 {
- label = "default-config";
- reg = <0x1f40000 0x10000>;
- read-only;
- };
-
- partition@1f50000 {
- label = "user-config";
- reg = <0x1f50000 0x40000>;
- read-only;
- };
-
- partition@1f90000 {
- label = "qos-db";
- reg = <0x1f90000 0x40000>;
- read-only;
- };
-
- partition@1fd0000 {
- label = "usb-config";
- reg = <0x1fd0000 0x10000>;
- read-only;
- };
-
- partition@1fe0000 {
- label = "log";
- reg = <0x1fe0000 0x20000>;
- read-only;
- };
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pin>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pin>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_defaultmac_8 (-1)>, <&precal_radio_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_defaultmac_8 0>, <&precal_radio_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_defaultmac_8 1>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_defaultmac_8 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/leds/common.h>
-
-#include "qcom-ipq8064-ad7200-c2600.dtsi"
-
-/ {
- model = "TP-Link Talon AD7200";
- compatible = "tplink,ad7200", "qcom,ipq8064";
-
- aliases {
- led-boot = &led_status;
- led-failsafe = &led_status;
- led-running = &led_status;
- led-upgrade = &led_status;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- led_enable {
- label = "led-enable";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- lan {
- function = LED_FUNCTION_LAN;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 2 GPIO_ACTIVE_HIGH>;
- };
-
- usb1 {
- label = "blue:usb1";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g {
- label = "blue:wlan5g";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
- };
-
- usb3 {
- label = "blue:usb3";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g {
- label = "blue:wlan2g";
- gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
- };
-
- wan_orange {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_ORANGE>;
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- wan_blue {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- };
-
- wlan60g {
- label = "blue:wlan60g";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- led_status: status {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio53", "gpio54", "gpio67";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio2", "gpio8", "gpio15", "gpio16", "gpio17", "gpio26",
- "gpio33", "gpio55", "gpio56", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-};
-
-&mdio0 {
- switch@10 {
- ports {
- port@1 {
- label = "wan";
- };
-
- port@2 {
- label = "lan1";
- };
-
- port@3 {
- label = "lan2";
- };
-
- port@4 {
- label = "lan3";
- };
-
- port@5 {
- label = "lan4";
- };
- };
- };
-};
-
-&pcie2 {
- status = "okay";
- max-link-speed = <1>;
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-/ {
- model = "Qualcomm Technologies, Inc. IPQ8064/AP-148";
- compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&flash {
- partitions {
- compatible = "qcom,smem-part";
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- /*
- port@6 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
- asym-pause;
- };
- };
- */
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-/ {
- model = "Qualcomm IPQ8064/AP161";
- compatible = "qcom,ipq8064-ap161", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
- };
-};
-
-&qcom_pinmux {
- rgmii2_pins: rgmii2-pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29",
- "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59",
- "gpio60", "gpio61", "gpio62",
- "gpio2", "gpio66";
- };
- };
-};
-
-&flash {
- partitions {
- compatible = "qcom,smem-part";
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-};
-
-&pcie2 {
- status = "okay";
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- /*
- port@6 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
- asym-pause;
- };
- };
- */
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-
- phy3: ethernet-phy@3 {
- device_type = "ethernet-phy";
- reg = <3>;
- };
-};
-
-&gmac0 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2014 The ChromiumOS Authors
- */
-
-#include "qcom-ipq8064-onhub.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-
-/ {
- model = "ASUS OnHub";
- compatible = "asus,onhub", "google,arkham", "qcom,ipq8064";
-};
-
-&qcom_pinmux {
- ap3223_pins: ap3223_pinmux {
- pins = "gpio22";
- function = "gpio";
- bias-none;
- };
-
- i2c7_pins: i2c7_pinmux {
- mux {
- pins = "gpio8", "gpio9";
- function = "gsbi7";
- };
- data {
- pins = "gpio8";
- bias-disable;
- };
- clk {
- pins = "gpio9";
- bias-disable;
- };
- };
-};
-
-&gsbi7 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi7_i2c {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c7_pins>;
- pinctrl-names = "default";
-
- ap3223@1c {
- compatible = "dynaimage,ap3223";
- reg = <0x1c>;
-
- pinctrl-0 = <&ap3223_pins>;
- pinctrl-names = "default";
-
- int-gpio = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
- };
-
- led-controller@32 {
- compatible = "national,lp5523";
- reg = <0x32>;
- clock-mode = /bits/ 8 <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@4 {
- reg = <4>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0xfa>;
- max-cur = /bits/ 8 <0xff>;
- };
-
- led@5 {
- reg = <5>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status";
- led-cur = /bits/ 8 <0xfa>;
- max-cur = /bits/ 8 <0xff>;
- };
-
- led@8 {
- reg = <8>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status";
- led-cur = /bits/ 8 <0xfa>;
- max-cur = /bits/ 8 <0xff>;
- };
- };
-};
+++ /dev/null
-#include <dt-bindings/leds/common.h>
-
-#include "qcom-ipq8064-ad7200-c2600.dtsi"
-
-/ {
- model = "TP-Link Archer C2600";
- compatible = "tplink,c2600", "qcom,ipq8064";
-
- aliases {
- led-boot = &power;
- led-failsafe = &general;
- led-running = &power;
- led-upgrade = &general;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- ledswitch {
- label = "ledswitch";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- lan {
- function = LED_FUNCTION_LAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
- };
-
- usb4 {
- label = "white:usb_4";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb_2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- wan_white {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
- };
-
- power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- general: general {
- label = "white:general";
- gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio16", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
- "gpio53", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-};
+++ /dev/null
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Netgear Nighthawk X4 D7800";
- compatible = "netgear,d7800", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- rsvd@5fe00000 {
- reg = <0x5fe00000 0x200000>;
- reusable;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- power_amber: power_amber {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power_white: power_white {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-};
-
-&sata_phy {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_art_6 1>, <&precal_art_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_art_6 2>, <&precal_art_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie2 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie2_pins>;
- pinctrl-names = "default";
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_art_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_art_6: macaddr@6 {
- compatible = "mac-base";
- reg = <0x6 0x6>;
- #nvmem-cell-cells = <1>;
- };
-
- precal_art_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_art_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x6080000>;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_art_6 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_art_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-/ {
- model = "Qualcomm IPQ8064/DB149";
- compatible = "qcom,ipq8064-db149", "qcom,ipq8064";
-
- aliases {
- serial0 = &gsbi2_serial;
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-};
-
-&qcom_pinmux {
- rgmii0_pins: rgmii0_pins {
- mux {
- pins = "gpio2", "gpio66";
- drive-strength = <8>;
- bias-disable;
- };
- };
-};
-
-&gsbi2 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
-
- gsbi2_serial: serial@12490000 {
- status = "okay";
- };
-};
-
-&gsbi4 {
- status = "disabled";
-};
-
-&gsbi4_serial {
- status = "disabled";
-};
-
-&flash {
- m25p,fast-read;
-
- partition@0 {
- label = "lowlevel_init";
- reg = <0x0 0x1b0000>;
- };
-
- partition@1 {
- label = "u-boot";
- reg = <0x1b0000 0x80000>;
- };
-
- partition@2 {
- label = "u-boot-env";
- reg = <0x230000 0x40000>;
- };
-
- partition@3 {
- label = "caldata";
- reg = <0x270000 0x40000>;
- };
-
- partition@4 {
- label = "firmware";
- reg = <0x2b0000 0x1d50000>;
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&pcie2 {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- /*
- port@6 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
- asym-pause;
- };
- };
- */
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-
- phy6: ethernet-phy@6 {
- reg = <6>;
- };
-
- phy7: ethernet-phy@7 {
- reg = <7>;
- };
-};
-
-&gmac0 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
-
- pinctrl-0 = <&rgmii0_pins>;
- pinctrl-names = "default";
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- phy-handle = <&phy6>;
-};
-
-&gmac3 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <3>;
- phy-handle = <&phy7>;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/leds/common.h>
-
-#include "qcom-ipq8064-eax500.dtsi"
-
-/ {
- model = "Linksys EA7500 V1 WiFi Router";
- compatible = "linksys,ea7500-v1", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0xe000000>;
- device_type = "memory";
- };
-
- aliases {
- led-boot = &led_power;
- led-failsafe = &led_power;
- led-running = &led_power;
- led-upgrade = &led_power;
- };
-
- chosen {
- /* look for root deviceblock nbr in this bootarg */
- find-rootblock = "ubi.mtd=";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- default-state = "keep";
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio65", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-};
-
-&partitions {
- partition@5f80000 {
- label = "sysdiag";
- reg = <0x5f80000 0x100000>;
- };
-
- partition@6080000 {
- label = "syscfg";
- reg = <0x6080000 0x1f80000>;
- };
-};
-
-&mdio0 {
- switch@10 {
- ports {
- port@1 {
- label = "wan";
- };
-
- port@2 {
- label = "lan1";
- };
-
- port@3 {
- label = "lan2";
- };
-
- port@4 {
- label = "lan3";
- };
-
- port@5 {
- label = "lan4";
- };
- };
- };
-};
+++ /dev/null
-#include <dt-bindings/leds/common.h>
-
-#include "qcom-ipq8064-eax500.dtsi"
-
-/ {
- model = "Linksys EA8500 WiFi Router";
- compatible = "linksys,ea8500", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &led_power;
- led-failsafe = &led_power;
- led-running = &led_power;
- led-upgrade = &led_power;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- led_power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- default-state = "keep";
- };
-
- wifi {
- label = "green:wifi";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio53", "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-};
-
-&sata_phy {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
-&partitions {
- partition@5f80000 {
- label = "syscfg";
- reg = <0x5f80000 0x2080000>;
- };
-};
-
-&gmac1 {
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <1>;
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
-};
-
-/* LAN */
-&gmac2 {
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- chosen {
- bootargs = "console=ttyMSM0,115200n8";
- /* append to bootargs adding the root deviceblock nbr from bootloader */
- append-rootblock = "ubi.mtd=";
- };
-};
-
-&qcom_pinmux {
- /* eax500 routers reuse the pcie2 reset pin for switch reset pin */
- switch_reset: switch_reset_pins {
- mux {
- pins = "gpio63";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-up;
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- max-link-speed = <1>;
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x0c80000>;
-
- partitions: partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- partition@40000 {
- label = "MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- partition@180000 {
- label = "SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- partition@2c0000 {
- label = "SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- partition@540000 {
- label = "DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- partition@660000 {
- label = "SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- partition@780000 {
- label = "TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- partition@a00000 {
- label = "RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- art: partition@c80000 {
- label = "art";
- reg = <0x0c80000 0x0140000>;
- read-only;
- };
-
- partition@dc0000 {
- label = "APPSBL";
- reg = <0x0dc0000 0x0100000>;
- read-only;
- };
-
- partition@ec0000 {
- label = "u_env";
- reg = <0x0ec0000 0x0040000>;
- };
-
- partition@f00000 {
- label = "s_env";
- reg = <0x0f00000 0x0040000>;
- };
-
- partition@f40000 {
- label = "devinfo";
- reg = <0x0f40000 0x0040000>;
- };
-
- partition@f80000 {
- label = "kernel1";
- reg = <0x0f80000 0x2800000>; /* 4 MB, spill to rootfs */
- };
-
- partition@1380000 {
- label = "rootfs1";
- reg = <0x1380000 0x2400000>;
- };
-
- partition@3780000 {
- label = "kernel2";
- reg = <0x3780000 0x2800000>;
- };
-
- partition@3b80000 {
- label = "rootfs2";
- reg = <0x3b80000 0x2400000>;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- /* Switch from documentation require at least 10ms for reset */
- reset-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_HIGH>;
- reset-post-delay-us = <12000>;
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8064-smb208.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Fortinet FAP-421E";
- compatible = "fortinet,fap-421e", "qcom,ipq8064";
-
- memory@42000000 {
- device_type = "memory";
- reg = <0x42000000 0xe000000>;
- };
-
- reserved-memory {
- rsvd@41200000 {
- no-map;
- reg = <0x41200000 0x300000>;
- };
- wifi_dump@44000000 {
- no-map;
- reg = <0x44000000 0x600000>;
- };
- };
-
- aliases {
- led-boot = &led_power_yellow;
- led-failsafe = &led_power_yellow;
- led-running = &led_power_yellow;
- led-upgrade = &led_power_yellow;
- label-mac-device = &gmac0;
- };
-
- chosen {
- bootargs-override = "console=ttyMSM0,9600n8";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- eth1-amber {
- label = "amber:eth1";
- gpios = <&qcom_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- eth1-yellow {
- label = "yellow:eth1";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- eth2-amber {
- label = "amber:eth2";
- gpios = <&qcom_pinmux 29 GPIO_ACTIVE_LOW>;
- };
-
- eth2-yellow {
- label = "yellow:eth2";
- gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
- };
-
- power-amber {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
- };
-
- led_power_yellow: power-yellow {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_YELLOW>;
- gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
- };
-
- 2g-yellow {
- label = "yellow:2g";
- gpios = <&qcom_pinmux 30 GPIO_ACTIVE_LOW>;
- };
-
- 5g-yellow {
- label = "yellow:5g";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- bias-pull-up;
- drive-strength = <2>;
- pins = "gpio56";
- };
- };
-
- led_pins: led_pins {
- mux {
- bias-pull-down;
- drive-strength = <2>;
- function = "gpio";
- output-low;
- pins = "gpio23";
- };
- };
-
- rgmii2_pins: rgmii2-pins {
- mux {
- bias-disable;
- drive-strength = <16>;
- function = "rgmii2";
- pins = "gpio66";
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- uart0_pins: uart0_pins {
- mux {
- bias-disable;
- drive-strength = <12>;
- function = "gsbi7";
- pins = "gpio6", "gpio7";
- };
- };
-
- usb_pwr_en_pins: usb_pwr_en_pins {
- mux {
- pins = "gpio22";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-low;
- };
- };
-};
-
-&gsbi7 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
-
- status = "okay";
-};
-
-&gsbi7_serial{
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
-
- status = "okay";
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
- m25p,fast-read;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- partition@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- partition@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- partition@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- partition@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- partition@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- partition@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- partition@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_appsbl_7ff80: mac-address@7ff80 {
- compatible = "mac-base";
- reg = <0x7ff80 0xc>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-
- partition@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x40000>;
- };
-
- partition@2e0000 {
- label = "ART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- partition@320000 {
- label = "kernel";
- reg = <0x320000 0x600000>;
- };
-
- partition@920000 {
- label = "ubi";
- reg = <0x920000 0x1400000>;
- };
-
- partition@1d20000 {
- label = "reserved";
- reg = <0x1d20000 0x260000>;
- read-only;
- };
-
- partition@1f80000 {
- label = "config";
- reg = <0x1f80000 0x80000>;
- read-only;
- };
- };
- };
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_appsbl_7ff80 8>;
- nvmem-cell-names = "mac-address";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_appsbl_7ff80 16>;
- nvmem-cell-names = "mac-address";
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- #address-cells = <0x1>;
- #size-cells = <0x0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
-
- phy2: ethernet-phy@2 {
- reg = <2>;
- };
-};
-
-&gmac0 {
- status = "okay";
-
- phy-mode = "rgmii";
- qcom,id = <0>;
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- nvmem-cells = <&macaddr_appsbl_7ff80 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
- nvmem-cells = <&macaddr_appsbl_7ff80 1>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- compatible = "asrock,g10", "qcom,ipq8064";
- model = "ASRock G10";
-
- aliases {
- ethernet0 = &gmac1;
- ethernet1 = &gmac0;
-
- led-boot = &led_status_blue;
- led-failsafe = &led_status_amber;
- led-running = &led_status_blue;
- led-upgrade = &led_status_amber;
- };
-
- chosen {
- bootargs-override = "console=ttyMSM0,115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- /*
- * this is a bit misleading. Because there are about seven
- * multicolor LEDs connected all wired together in parallel.
- */
-
- status_yellow {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_YELLOW>;
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- led_status_amber: status_amber {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- led_status_blue: status_blue {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- /*
- * LED is declared in vendors boardfile but it's not
- * working and the manual doesn't mention anything
- * about the LED being white.
-
- status_white {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- */
- };
-
- i2c-gpio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- compatible = "i2c-gpio";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>, /* sda */
- <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; /* scl */
- i2c-gpio,delay-us = <5>;
- i2c-gpio,scl-output-only;
-
- mcu@50 {
- reg = <0x50>;
- compatible = "sonix,sn8f25e21";
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- ir-remote {
- label = "ir-remote";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_0>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps5g {
- label = "wps5g";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps2g {
- label = "wps2g";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&gmac1 {
- status = "okay";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi4_serial {
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1200000>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi5g: wifi@1,0 {
- reg = <0x00010000 0 0 0 0>;
- compatible = "qcom,ath10k";
- qcom,ath10k-calibration-variant = "ASRock-G10";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi2g: wifi@1,0 {
- reg = <0x00010000 0 0 0 0>;
- compatible = "qcom,ath10k";
- qcom,ath10k-calibration-variant = "ASRock-G10";
- };
- };
-};
-
-&qcom_pinmux {
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio26";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio15", "gpio16", "gpio64", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- uart0_pins: uart0_pins {
- mux {
- pins = "gpio10", "gpio11";
- function = "gsbi4";
- drive-strength = <10>;
- bias-disable;
- };
- };
-};
-
-&rpm {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&tcsr {
- qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
-};
-
-/delete-node/ &pcie2_pins;
-/delete-node/ &pcie2;
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2014 The ChromiumOS Authors
- */
-
-#include "qcom-ipq8064-smb208.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- aliases {
- ethernet0 = &gmac0;
- ethernet1 = &gmac2;
- mdio-gpio0 = &mdio;
- serial0 = &gsbi4_serial;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- dev {
- label = "dev";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_CONFIG>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- mdio: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
- };
- };
- };
-
- soc {
- rng@1a500000 {
- status = "disabled";
- };
-
- sound {
- compatible = "google,storm-audio";
- qcom,model = "ipq806x-storm";
- cpu = <&lpass>;
- codec = <&max98357a>;
- };
-
- lpass: lpass@28100000 {
- status = "okay";
- pinctrl-names = "default", "idle";
- pinctrl-0 = <&mi2s_default>;
- pinctrl-1 = <&mi2s_idle>;
- };
-
- max98357a: max98357a {
- compatible = "maxim,max98357a";
- #sound-dai-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmode_pins>;
- sdmode-gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- rgmii0_pins: rgmii0_pins {
- mux {
- pins = "gpio2", "gpio66";
- drive-strength = <8>;
- bias-disable;
- };
- };
- mi2s_pins {
- mi2s_default: mi2s_default {
- dout {
- pins = "gpio32";
- function = "mi2s";
- drive-strength = <16>;
- bias-disable;
- };
- sync {
- pins = "gpio27";
- function = "mi2s";
- drive-strength = <16>;
- bias-disable;
- };
- clk {
- pins = "gpio28";
- function = "mi2s";
- drive-strength = <16>;
- bias-disable;
- };
- };
- mi2s_idle: mi2s_idle {
- dout {
- pins = "gpio32";
- function = "mi2s";
- drive-strength = <2>;
- bias-pull-down;
- };
- sync {
- pins = "gpio27";
- function = "mi2s";
- drive-strength = <2>;
- bias-pull-down;
- };
- clk {
- pins = "gpio28";
- function = "mi2s";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
- };
-
- mdio_pins: mdio_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- rst {
- pins = "gpio26";
- output-low;
- };
- };
-
- sdmode_pins: sdmode_pinmux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <16>;
- bias-disable;
- };
-
- sdcc1_pins: sdcc1_pinmux {
- mux {
- pins = "gpio38", "gpio39", "gpio40",
- "gpio41", "gpio42", "gpio43",
- "gpio44", "gpio45", "gpio46",
- "gpio47";
- function = "sdc1";
- };
- cmd {
- pins = "gpio45";
- drive-strength = <10>;
- bias-pull-up;
- };
- data {
- pins = "gpio38", "gpio39", "gpio40",
- "gpio41", "gpio43", "gpio44",
- "gpio46", "gpio47";
- drive-strength = <10>;
- bias-pull-up;
- };
- clk {
- pins = "gpio42";
- drive-strength = <16>;
- bias-pull-down;
- };
- };
-
- i2c1_pins: i2c1_pinmux {
- pins = "gpio53", "gpio54";
- function = "gsbi1";
- bias-disable;
- };
-
- rpm_i2c_pinmux: rpm_i2c_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- /delete-property/ bias-none;
- /delete-property/ drive-strength;
- };
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- fw_pinmux {
- wp {
- pins = "gpio17";
- output-low;
- };
- };
-
- button_pins: button_pins {
- recovery {
- pins = "gpio16";
- function = "gpio";
- bias-none;
- };
- developer {
- pins = "gpio15";
- function = "gpio";
- bias-none;
- };
- };
-
- spi6_pins: spi6_pins {
- mux {
- pins = "gpio55", "gpio56", "gpio58";
- function = "gsbi6";
- bias-pull-down;
- };
- data {
- pins = "gpio55", "gpio56";
- drive-strength = <10>;
- };
- cs {
- pins = "gpio57";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- clk {
- pins = "gpio58";
- drive-strength = <12>;
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&gmac0 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
-
- pinctrl-0 = <&rgmii0_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi1 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi1_i2c {
- status = "okay";
-
- clock-frequency = <100000>;
-
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
-
- tpm@20 {
- compatible = "infineon,slb9645tt";
- reg = <0x20>;
- powered-while-suspended;
- };
-};
-
-&gsbi4 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi4_serial {
- status = "okay";
-};
-
-&gsbi5 {
- status = "okay";
- qcom,mode = <GSBI_PROT_SPI>;
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 0>;
-
- flash: flash@0 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
- };
- };
-};
-
-&gsbi6 {
- status = "okay";
- qcom,mode = <GSBI_PROT_SPI>;
-};
-
-&gsbi6_spi {
- status = "okay";
- spi-max-frequency = <25000000>;
-
- pinctrl-0 = <&spi6_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
-
- dmas = <&adm_dma 8 0xb>,
- <&adm_dma 7 0x14>;
- dma-names = "rx", "tx";
-
- /*
- * This "spidev" was included in the manufacturer device tree. I suspect
- * it's the (unused) Zigbee radio -- SiliconLabs EM3581 Zigbee? There's
- * no driver or binding for this at the moment.
- */
- spidev@0 {
- compatible = "spidev";
- reg = <0>;
- spi-max-frequency = <25000000>;
- };
-};
-
-&pcie0 {
- status = "okay";
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-controller;
-
- ath10k@0,0 {
- reg = <0 0 0 0 0>;
- device_type = "pci";
- qcom,ath10k-sa-gpio = <2 3 4 0>;
- qcom,ath10k-sa-gpio-func = <5 5 5 0>;
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-controller;
-
- ath10k@0,0 {
- reg = <0 0 0 0 0>;
- device_type = "pci";
- qcom,ath10k-sa-gpio = <2 3 4 0>;
- qcom,ath10k-sa-gpio-func = <5 5 5 0>;
- };
- };
-};
-
-&pcie2 {
- status = "okay";
-
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- interrupt-controller;
-
- ath10k@0,0 {
- reg = <0 0 0 0 0>;
- device_type = "pci";
- };
- };
-};
-
-&rpm {
- pinctrl-0 = <&rpm_i2c_pinmux>;
- pinctrl-names = "default";
-};
-
-&sdcc1 {
- status = "okay";
- pinctrl-0 = <&sdcc1_pins>;
- pinctrl-names = "default";
- /delete-property/ mmc-ddr-1_8v;
-};
-
-&tcsr {
- compatible = "qcom,tcsr-ipq8064", "qcom,tcsr", "syscon";
- qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- model = "Netgear Nighthawk X4 R7500";
- compatible = "netgear,r7500", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0xe000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- power_amber: power_amber {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power_white: power_white {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-};
-
-&gsbi5 {
- status = "disabled";
-
- spi@1a280000 {
- status = "disabled";
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_art_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_art_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
- };
- };
-
- kernel@1340000 {
- label = "kernel";
- reg = <0x1340000 0x0400000>;
- };
-
- ubi@1740000 {
- label = "ubi";
- reg = <0x1740000 0x1600000>;
- };
-
- netgear@2d40000 {
- label = "netgear";
- reg = <0x2d40000 0x0c00000>;
- read-only;
- };
-
- reserve@3940000 {
- label = "reserve";
- reg = <0x3940000 0x46c0000>;
- read-only;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_art_6>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_art_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&tcsr {
- qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
- compatible = "qcom,tcsr";
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Netgear Nighthawk X4 R7500v2";
- compatible = "netgear,r7500v2", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- rsvd@5fe00000 {
- reg = <0x5fe00000 0x200000>;
- reusable;
- };
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &power;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "amber:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb3 {
- label = "amber:usb3";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- status {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- internet {
- label = "white:internet";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-};
-
-&sata_phy {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_art_6 1>, <&precal_art_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_art_6 2>, <&precal_art_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_art_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_art_6: macaddr@6 {
- compatible = "mac-base";
- reg = <0x6 0x6>;
- #nvmem-cell-cells = <1>;
- };
-
- precal_art_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_art_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x6080000>;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_art_6 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_art_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2014 The ChromiumOS Authors
- */
-
-#include "qcom-ipq8064-onhub.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-
-/ {
- model = "TP-Link OnHub";
- compatible = "tplink,onhub", "google,whirlwind-sp5", "qcom,ipq8064";
-};
-
-&qcom_pinmux {
- i2c7_pins: i2c7_pinmux {
- mux {
- pins = "gpio8", "gpio9";
- function = "gsbi7";
- };
- data {
- pins = "gpio8";
- bias-disable;
- };
- clk {
- pins = "gpio9";
- bias-disable;
- };
- };
-};
-
-&gsbi7 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi7_i2c {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c7_pins>;
- pinctrl-names = "default";
-
- led-controller@32 {
- compatible = "national,lp5523";
- reg = <0x32>;
- clock-mode = /bits/ 8 <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-0";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-0";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-0";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@3 {
- reg = <3>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-1";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@4 {
- reg = <4>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-1";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@5 {
- reg = <5>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-1";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@6 {
- reg = <6>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-2";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@7 {
- reg = <7>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-2";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@8 {
- reg = <8>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-2";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
- };
-
- led-controller@33 {
- compatible = "national,lp5523";
- reg = <0x33>;
- clock-mode = /bits/ 8 <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-3";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-3";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-3";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@3 {
- reg = <3>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-4";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@4 {
- reg = <4>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-4";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@5 {
- reg = <5>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-4";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@6 {
- reg = <6>;
- color = <LED_COLOR_ID_RED>;
- chan-name = "red:status-5";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@7 {
- reg = <7>;
- color = <LED_COLOR_ID_GREEN>;
- chan-name = "green:status-5";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
-
- led@8 {
- reg = <8>;
- color = <LED_COLOR_ID_BLUE>;
- chan-name = "blue:status-5";
- linux,default-trigger = "default-on";
- led-cur = /bits/ 8 <0x64>;
- max-cur = /bits/ 8 <0x78>;
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Ubiquiti UniFi AC HD";
- compatible = "ubnt,unifi-ac-hd", "qcom,ipq8064";
-
- aliases {
- label-mac-device = &gmac2;
- led-boot = &led_dome_white;
- led-failsafe = &led_dome_white;
- led-running = &led_dome_blue;
- led-upgrade = &led_dome_blue;
- mdio-gpio0 = &mdio0;
- ethernet0 = &gmac2;
- ethernet1 = &gmac1;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_dome_blue: dome_blue {
- label = "blue:dome";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- led_dome_white: dome_white {
- label = "white:dome";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio9", "gpio53";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- output-low;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-};
-
-&CPU_SPC {
- status = "disabled";
-};
-
-&gsbi5 {
- status = "okay";
-
- qcom,mode = <GSBI_PROT_SPI>;
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
- cs-gpios = <&qcom_pinmux 20 0>;
-
- flash@0 {
- compatible = "mx25u25635f", "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- label = "MIBIB";
- reg = <0x20000 0x10000>;
- read-only;
- };
-
- partition@30000 {
- label = "SBL2";
- reg = <0x30000 0x20000>;
- read-only;
- };
-
- partition@50000 {
- label = "SBL3";
- reg = <0x50000 0x30000>;
- read-only;
- };
-
- partition@80000 {
- label = "DDRCONFIG";
- reg = <0x80000 0x10000>;
- read-only;
- };
-
- partition@90000 {
- label = "SSD";
- reg = <0x90000 0x10000>;
- read-only;
- };
-
- partition@a0000 {
- label = "TZ";
- reg = <0xa0000 0x30000>;
- read-only;
- };
-
- partition@d0000 {
- label = "RPM";
- reg = <0xd0000 0x20000>;
- read-only;
- };
-
- partition@f0000 {
- label = "APPSBL";
- reg = <0xf0000 0xc0000>;
- read-only;
- };
-
- partition@1b0000 {
- label = "APPSBLENV";
- reg = <0x1b0000 0x10000>;
- read-only;
- };
-
- eeprom: partition@1c0000 {
- label = "EEPROM";
- reg = <0x1c0000 0x10000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_eeprom_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_eeprom_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
- };
- };
-
- partition@1d0000 {
- label = "bootselect";
- reg = <0x1d0000 0x10000>;
- };
-
- partition@1e0000 {
- compatible = "denx,fit";
- label = "firmware";
- reg = <0x1e0000 0xe70000>;
- };
-
- partition@1050000 {
- label = "kernel1";
- reg = <0x1050000 0xe70000>;
- read-only;
- };
-
- partition@1ec0000 {
- label = "debug";
- reg = <0x1ec0000 0x100000>;
- read-only;
- };
-
- partition@1fc0000 {
- label = "cfg";
- reg = <0x1fc0000 0x40000>;
- read-only;
- };
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&nand {
- status = "okay";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy4: ethernet-phy@4 {
- reg = <4>;
- };
-
- phy5: ethernet-phy@5 {
- reg = <5>;
- };
-};
-
-&gmac1 {
- status = "okay";
-
- mdiobus = <&mdio0>;
- phy-handle = <&phy5>;
- phy-mode = "sgmii";
- qcom,id = <1>;
-
- nvmem-cells = <&macaddr_eeprom_6>;
- nvmem-cell-names = "mac-address";
-};
-
-&gmac2 {
- status = "okay";
-
- mdiobus = <&mdio0>;
- phy-handle = <&phy4>;
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_eeprom_0>;
- nvmem-cell-names = "mac-address";
-};
-
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&tcsr {
- status = "okay";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "TP-Link Archer VR2600v";
- compatible = "tplink,vr2600v", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &general;
- led-running = &power;
- led-upgrade = &general;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- dect {
- label = "dect";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_PHONE>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- ledswitch {
- label = "ledswitch";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- dsl {
- label = "white:dsl";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb {
- function = LED_FUNCTION_USB;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- lan {
- function = LED_FUNCTION_LAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g {
- label = "white:wlan2g";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g {
- label = "white:wlan5g";
- gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- phone {
- label = "white:phone";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- wan {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- general: general {
- label = "white:general";
- gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
- "gpio26", "gpio53", "gpio56", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- partition@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- partition@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- partition@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- partition@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- partition@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- partition@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- partition@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- partition@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x40000>;
- read-only;
- };
-
- partition@2e0000 {
- label = "OLDART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- partition@320000 {
- label = "firmware";
- reg = <0x320000 0xc60000>;
- compatible = "openwrt,uimage";
- openwrt,offset = <512>; /* account for pad-extra 512 */
- };
-
- /* hole 0xf80000 - 0xfaf100 */
-
- partition@faf100 {
- label = "default-mac";
- reg = <0xfaf100 0x00200>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_defaultmac_0: macaddr@0 {
- compatible = "mac-base";
- reg = <0x0 0x6>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-
- partition@fc0000 {
- label = "ART";
- reg = <0xfc0000 0x40000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_defaultmac_0 (-1)>, <&precal_ART_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_defaultmac_0 0>, <&precal_ART_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_defaultmac_0 1>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_defaultmac_0 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "NEC Aterm WG2600HP";
- compatible = "nec,wg2600hp", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_green;
- led-failsafe = &power_red;
- led-running = &power_green;
- led-upgrade = &power_green;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- bridge {
- label = "bridge";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_0>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- converter {
- label = "converter";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_0>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- converter_green {
- label = "green:converter";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
- };
-
- power_red: power_red {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- active_green {
- label = "green:active";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- active_red {
- label = "red:active";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- power_green: power_green {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
- };
-
- converter_red {
- label = "red:converter";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g_green {
- label = "green:wlan2g";
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g_red {
- label = "red:wlan2g";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g_green {
- label = "green:wlan5g";
- gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g_red {
- label = "red:wlan5g";
- gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>;
- };
-
- tv_green {
- label = "green:tv";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- tv_red {
- label = "red:tv";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&CPU_SPC {
- status = "disabled";
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
-switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
- qca,sgmii-rxclk-falling-edge;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_PRODUCTDATA_6>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_PRODUCTDATA_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi5 {
- status = "okay";
-
- qcom,mode = <GSBI_PROT_SPI>;
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- SBL3@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- DDRCONFIG@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- SSD@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- TZ@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- RPM@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- APPSBL@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- APPSBLENV@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x10000>;
- };
-
- PRODUCTDATA: PRODUCTDATA@2b0000 {
- label = "PRODUCTDATA";
- reg = <0x2b0000 0x30000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_PRODUCTDATA_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_PRODUCTDATA_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
-
- macaddr_PRODUCTDATA_c: macaddr@c {
- reg = <0xc 0x6>;
- };
-
- macaddr_PRODUCTDATA_12: macaddr@12 {
- reg = <0x12 0x6>;
- };
- };
- };
-
- ART@2e0000 {
- label = "ART";
- reg = <0x2e0000 0x40000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- TP@320000 {
- label = "TP";
- reg = <0x320000 0x40000>;
- read-only;
- };
-
- TINY@360000 {
- label = "TINY";
- reg = <0x360000 0x500000>;
- read-only;
- };
-
- firmware@860000 {
- compatible = "denx,uimage";
- label = "firmware";
- reg = <0x860000 0x17a0000>;
- };
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_PRODUCTDATA_12>, <&precal_ART_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_PRODUCTDATA_c>, <&precal_ART_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio16", "gpio54", "gpio24", "gpio25";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
- "gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
- "gpio64", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- usb_pwr_en_pins: usb_pwr_en_pins {
- mux {
- pins = "gpio22";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- output-high;
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (C) 2017 Christian Mehlis <christian@m3hlis.de>
- * Copyright (C) 2018 Mathias Kresin <dev@kresin.me>
- * All rights reserved.
- */
-
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- compatible = "compex,wpq864", "qcom,ipq8064";
- model = "Compex WPQ864";
-
- aliases {
- mdio-gpio0 = &mdio0;
- ethernet0 = &gmac1;
- ethernet1 = &gmac0;
-
- led-boot = &led_pass;
- led-failsafe = &led_fail;
- led-running = &led_pass;
- led-upgrade = &led_pass;
- };
-
- leds {
- compatible = "gpio-leds";
-
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- rss4 {
- label = "green:rss4";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- rss3 {
- label = "green:rss3";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- rss2 {
- label = "orange:rss2";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
- };
-
- rss1 {
- label = "red:rss1";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- led_pass: pass {
- label = "green:pass";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- led_fail: fail {
- label = "green:fail";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- usb {
- function = LED_FUNCTION_USB;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb-pcie {
- label = "green:usb-pcie";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- beeper {
- compatible = "gpio-beeper";
-
- pinctrl-0 = <&beeper_pins>;
- pinctrl-names = "default";
-
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&rpm {
- pinctrl-0 = <&rpm_pins>;
- pinctrl-names = "default";
-};
-
-&nand {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- mt29f2g08abbeah4@0 {
- compatible = "qcom,nandcs";
-
- reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000 0x5340000 0x10c0000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "0:SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- partition@40000 {
- label = "0:MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- partition@180000 {
- label = "0:SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- partition@2c0000 {
- label = "0:SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- partition@540000 {
- label = "0:DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- partition@660000 {
- label = "0:SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- partition@780000 {
- label = "0:TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- partition@a00000 {
- label = "0:RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- partition@c80000 {
- label = "0:APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- partition@1180000 {
- label = "0:APPSBLENV";
- reg = <0x1180000 0x0080000>;
- };
-
- partition@1200000 {
- label = "0:ART";
- reg = <0x1200000 0x0140000>;
- };
-
- partition@1340000 {
- label = "ubi";
- reg = <0x1340000 0x4000000>;
- };
-
- partition@5340000 {
- label = "0:BOOTCONFIG";
- reg = <0x5340000 0x0060000>;
- };
-
- partition@53a0000 {
- label = "0:SBL2_1";
- reg = <0x53a0000 0x0140000>;
- read-only;
- };
-
- partition@54e0000 {
- label = "0:SBL3_1";
- reg = <0x54e0000 0x0280000>;
- read-only;
- };
-
- partition@5760000 {
- label = "0:DDRCONFIG_1";
- reg = <0x5760000 0x0120000>;
- read-only;
- };
-
- partition@5880000 {
- label = "0:SSD_1";
- reg = <0x5880000 0x0120000>;
- read-only;
- };
-
- partition@59a0000 {
- label = "0:TZ_1";
- reg = <0x59a0000 0x0280000>;
- read-only;
- };
-
- partition@5c20000 {
- label = "0:RPM_1";
- reg = <0x5c20000 0x0280000>;
- read-only;
- };
-
- partition@5ea0000 {
- label = "0:BOOTCONFIG1";
- reg = <0x5ea0000 0x0060000>;
- };
-
- partition@5f00000 {
- label = "0:APPSBL_1";
- reg = <0x5f00000 0x0500000>;
- read-only;
- };
-
- partition@6400000 {
- label = "ubi_1";
- reg = <0x6400000 0x4000000>;
- };
-
- partition@a400000 {
- label = "unused";
- reg = <0xa400000 0x5c00000>;
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi4_serial {
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
-};
-
-&flash {
- compatible = "jedec,spi-nor";
-};
-
-&sata_phy {
- status = "disabled";
-};
-
-&sata {
- status = "disabled";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-
- rx_eq = <2>;
- tx_deamp_3_5db = <32>;
- mpll = <160>;
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-
- rx_eq = <2>;
- tx_deamp_3_5db = <32>;
- mpll = <160>;
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&pcie2 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-};
-
-&qcom_pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinctrl0 {
- pcie0_pcie2_perst {
- pins = "gpio3";
- function = "gpio";
- drive-strength = <2>;
- bias-disable;
- output-high;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22",
- "gpio23", "gpio24", "gpio25", "gpio53";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- beeper_pins: beeper_pins {
- mux {
- pins = "gpio55";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- rpm_pins: rpm_pins {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <10>;
- bias-disable;
- };
- };
-
- uart0_pins: uart0_pins {
- mux {
- pins = "gpio10", "gpio11";
- function = "gsbi4";
- drive-strength = <10>;
- bias-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19";
- function = "gsbi5";
- drive-strength = <10>;
- bias-pull-down;
- };
-
- clk {
- pins = "gpio21";
- function = "gsbi5";
- drive-strength = <12>;
- bias-pull-down;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-};
-
-&tcsr {
- qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Buffalo WXR-2533DHP";
- compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
-
- memory@42000000 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- led-boot = &power;
- led-failsafe = &diag;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- /* use "ubi_rootfs" volume in "ubi" partition as rootfs */
- bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb {
- function = LED_FUNCTION_USB;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "usbport";
- trigger-sources = <&hub_port0 &hub_port1>;
- };
-
- guestport {
- label = "green:guestport";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- diag: diag {
- label = "orange:diag";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- internet_orange {
- label = "orange:internet";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
- };
-
- internet_white {
- label = "white:internet";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wireless_orange {
- label = "orange:wireless";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wireless_white {
- label = "white:wireless";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- router_orange {
- label = "orange:router";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
- };
-
- router_white {
- label = "white:router";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- power {
- label = "power";
- gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- eject {
- label = "eject";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_EJECTCD>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- guest {
- label = "guest";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_0>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- ap {
- label = "ap";
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_1>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- router {
- label = "router";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_1>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- auto {
- label = "auto";
- gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
- linux,code = <BTN_1>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-};
-
-&nand {
- status = "okay";
-
- cs@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- ubi@0 {
- label = "ubi";
- reg = <0x0000000 0x4000000>;
- };
-
- rootfs_1@4000000 {
- label = "rootfs_1";
- reg = <0x4000000 0x4000000>;
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_ART_6>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- nvmem-cells = <&macaddr_ART_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi4_serial {
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
-};
-
-&gsbi5 {
- status = "okay";
- qcom,mode = <GSBI_PROT_SPI>;
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x10000>;
- read-only;
- };
-
- MIBIB@10000 {
- label = "MIBIB";
- reg = <0x10000 0x20000>;
- read-only;
- };
-
- SBL2@30000 {
- label = "SBL2";
- reg = <0x30000 0x30000>;
- read-only;
- };
-
- SBL3@60000 {
- label = "SBL3";
- reg = <0x60000 0x30000>;
- read-only;
- };
-
- DDRCONFIG@90000 {
- label = "DDRCONFIG";
- reg = <0x90000 0x10000>;
- read-only;
- };
-
- SSD@a0000 {
- label = "SSD";
- reg = <0xa0000 0x10000>;
- read-only;
- };
-
- TZ@b0000 {
- label = "TZ";
- reg = <0xb0000 0x30000>;
- read-only;
- };
-
- RPM@e0000 {
- label = "RPM";
- reg = <0xe0000 0x20000>;
- read-only;
- };
-
- APPSBL@100000 {
- label = "APPSBL";
- reg = <0x100000 0x70000>;
- read-only;
- };
-
- APPSBLENV@170000 {
- label = "APPSBLENV";
- reg = <0x170000 0x10000>;
- read-only;
- };
-
- ART@180000 {
- label = "ART";
- reg = <0x180000 0x40000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_ART_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_ART_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
-
- macaddr_ART_18: macaddr@18 {
- reg = <0x18 0x6>;
- };
-
- macaddr_ART_1e: macaddr@1e {
- reg = <0x1e 0x6>;
- };
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- BOOTCONFIG@1c0000 {
- label = "BOOTCONFIG";
- reg = <0x1c0000 0x10000>;
- read-only;
- };
-
- APPSBL_1@1d0000 {
- label = "APPSBL_1";
- reg = <0x1d0000 0x70000>;
- read-only;
- };
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&dwc3_0 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- hub_port0: port@1 {
- reg = <1>;
- #trigger-source-cells = <0>;
- };
-};
-
-&dwc3_1 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- hub_port1: port@1 {
- reg = <1>;
- #trigger-source-cells = <0>;
- };
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_ART_1e>, <&precal_ART_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&macaddr_ART_18>, <&precal_ART_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
- "gpio58", "gpio64", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
- "gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- uart0_pins: uart0_pins {
- mux {
- pins = "gpio10", "gpio11";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs{
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- usb_pwr_en_pins: usb_pwr_en_pins {
- mux{
- pins = "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- output-high;
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8065-smb208.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Nokia AC400i";
- compatible = "nokia,ac400i", "qcom,ipq8065", "qcom,ipq8064";
-
- aliases {
- mdio-gpio0 = &mdio0;
- ethernet0 = &gmac0;
- ethernet1 = &gmac1;
-
- led-boot = &pwr_red;
- led-failsafe = &pwr_red;
- led-running = &pwr_green;
- led-upgrade = &pwr_green;
- };
-
- chosen {
- bootargs-override = " console=ttyMSM0,115200n8 ubi.mtd=ubi root=/dev/ubiblock0_2";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 15 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- 5g_red {
- label = "red:5g";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>;
- };
-
- 5g_green {
- label = "green:5g";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- 2g_red {
- label = "red:2g";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- 2g_green {
- label = "green:2g";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
- };
-
- eth1_red {
- label = "red:eth1";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_HIGH>;
- };
-
- eth1_green {
- label = "green:eth1";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
- };
-
- eth2_red {
- label = "red:eth2";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_HIGH>;
- };
-
- eth2_green {
- label = "green:eth2";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
- };
-
- ctrl_red {
- label = "red:ctrl";
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- };
-
- ctrl_green {
- label = "green:ctrl";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- pwr_red: pwr_red {
- label = "red:pwr";
- gpios = <&qcom_pinmux 2 GPIO_ACTIVE_LOW>;
- };
-
- pwr_green: pwr_green {
- label = "green:pwr";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19";
- function = "gsbi5";
- drive-strength = <10>;
- bias-pull-down;
- };
-
- clk {
- pins = "gpio21";
- function = "gsbi5";
- drive-strength = <12>;
- bias-pull-down;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio65", "gpio64",
- "gpio53", "gpio54",
- "gpio68", "gpio22",
- "gpio67", "gpio23",
- "gpio55", "gpio56",
- "gpio2", "gpio26";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
- };
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- qcom,ath10k-calibration-variant = "Nokia-AC400i";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- qcom,ath10k-calibration-variant = "Nokia-AC400i";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
-
-};
-
-//POE
-&gmac0 {
- status = "okay";
- qcom,id = <0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mdiobus = <&mdio0>;
- phy-handle = <&phy0>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-//LAN1
-&gmac1 {
- status = "okay";
- qcom,id = <1>;
-
- mdiobus = <&mdio0>;
- phy-handle = <&phy1>;
- phy-mode = "rgmii";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&nand {
- status = "okay";
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- rootfs@0 {
- label = "rootfs";
- reg = <0x0000000 0x4000000>;
- };
-
- rootfs_1@4000000 {
- label = "rootfs_1";
- reg = <0x4000000 0x4000000>;
- };
-
- cfg@8000000 {
- label = "cfg";
- reg = <0x8000000 0x8000000>;
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8065-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "ZyXEL NBG6817";
- compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
- sdcc1 = &sdcc1;
-
- led-boot = &power;
- led-failsafe = &power;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
- append-rootblock = "root=/dev/mmcblk0p";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- linux,input-type = <EV_SW>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- internet {
- label = "white:internet";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi2g {
- label = "amber:wifi2g";
- gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
- };
-
- /* wifi2g amber from the manual is missing */
-
- wifi5g {
- label = "amber:wifi5g";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- /* wifi5g amber from the manual is missing */
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio53", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio9", "gpio26", "gpio33", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- mdio0_pins: mdio0-pins {
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2-pins {
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio17";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio17";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio16";
- bias-pull-up;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio14", "gpio15";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio14";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio15";
- bias-pull-up;
- };
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <51200000>;
- reg = <0>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-};
-
-&pcie1 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- max-link-speed = <1>;
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&sdcc1 {
- status = "okay";
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-#include "qcom-ipq8065-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- rsvd@5fe00000 {
- reg = <0x5fe00000 0x200000>;
- reusable;
- };
-
- ramoops@42100000 {
- compatible = "ramoops";
- reg = <0x42100000 0x40000>;
- record-size = <0x4000>;
- console-size = <0x4000>;
- ftrace-size = <0x4000>;
- pmsg-size = <0x4000>;
- };
- };
-
- aliases {
- label-mac-device = &gmac2;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
-
- mdio-gpio0 = &mdio0;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- power_white: power_white {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- power_amber: power_amber {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- function = LED_FUNCTION_WAN;
- color = <LED_COLOR_ID_AMBER>;
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wifi {
- label = "white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- function = LED_FUNCTION_WPS;
- color = <LED_COLOR_ID_WHITE>;
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9",
- "gpio22", "gpio23", "gpio24",
- "gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- mdio0_pins: mdio0-pins {
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2-pins {
- tx {
- pins = "gpio27", "gpio28", "gpio29",
- "gpio30", "gpio31", "gpio32";
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- spi6_pins: spi6_pins {
- mux {
- pins = "gpio55", "gpio56", "gpio58";
- function = "gsbi6";
- bias-pull-down;
- };
-
- mosi {
- pins = "gpio55";
- drive-strength = <12>;
- };
-
- miso {
- pins = "gpio56";
- drive-strength = <14>;
- };
-
- cs {
- pins = "gpio57";
- drive-strength = <12>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio58";
- drive-strength = <12>;
- };
-
- reset {
- pins = "gpio33";
- drive-strength = <10>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000>;
-
- partitions: partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- partition@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- partition@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: partition@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_art_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_art_6: macaddr@6 {
- compatible = "mac-base";
- reg = <0x6 0x6>;
- #nvmem-cell-cells = <1>;
- };
-
- macaddr_art_c: macaddr@c {
- reg = <0xc 0x6>;
- };
-
- precal_art_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_art_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- partition@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- partition@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- nvmem-cells = <&macaddr_art_6 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- nvmem-cells = <&macaddr_art_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&sata_phy {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
-};
-
-&pcie0 {
- status = "okay";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi0: wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi1: wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
- };
- };
-};
+++ /dev/null
-#include "qcom-ipq8065-nighthawk.dtsi"
-
-/ {
- model = "Netgear Nighthawk X4S R7800";
- compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
-};
-
-&leds {
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&partitions {
- partition@1880000 {
- label = "ubi";
- reg = <0x1880000 0x6080000>;
- };
-
- partition@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
-};
-
-&wifi0 {
- nvmem-cells = <&macaddr_art_6 1>, <&precal_art_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
-
-&wifi1 {
- nvmem-cells = <&macaddr_art_6 2>, <&precal_art_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later
-
-#include "qcom-ipq8065-smb208.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Askey RT4230W REV6";
- compatible = "askey,rt4230w-rev6", "qcom,ipq8065", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x3e000000>;
- device_type = "memory";
- };
-
- aliases {
- led-boot = &ledctrl3;
- led-failsafe = &ledctrl1;
- led-running = &ledctrl2;
- led-upgrade = &ledctrl3;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- ledctrl1: ledctrl1 {
- label = "ledctrl1";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- ledctrl2: ledctrl2 {
- label = "ledctrl2";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- ledctrl3: ledctrl3 {
- label = "ledctrl3";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio54", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio22", "gpio23", "gpio24";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- rgmii2_pins: rgmii2-pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62";
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
-
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32";
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "everspin,mr25h256";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- qcom,boot-partitions = <0x0 0x1180000 0x1340000 0x10c0000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "0:SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- partition@40000 {
- label = "0:MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- partition@180000 {
- label = "0:SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- partition@2c0000 {
- label = "0:SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- partition@540000 {
- label = "0:DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- partition@660000 {
- label = "0:SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- partition@780000 {
- label = "0:TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- partition@a00000 {
- label = "0:RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- partition@c80000 {
- label = "0:APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- partition@1180000 {
- label = "0:APPSBLENV";
- reg = <0x1180000 0x0080000>;
- };
-
- partition@1200000 {
- label = "0:ART";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_ART_0: macaddr@0 {
- reg = <0x0 0x6>;
- };
-
- macaddr_ART_6: macaddr@6 {
- reg = <0x6 0x6>;
- };
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- partition@1340000 {
- label = "0:BOOTCONFIG";
- reg = <0x1340000 0x0060000>;
- read-only;
- };
-
- partition@13a0000 {
- label = "0:SBL2_1";
- reg = <0x13a0000 0x0140000>;
- read-only;
- };
-
- partition@14e0000 {
- label = "0:SBL3_1";
- reg = <0x14e0000 0x0280000>;
- read-only;
- };
-
- partition@1760000 {
- label = "0:DDRCONFIG_1";
- reg = <0x1760000 0x0120000>;
- read-only;
- };
-
- partition@1880000 {
- label = "0:SSD_1";
- reg = <0x1880000 0x0120000>;
- read-only;
- };
-
- partition@19a0000 {
- label = "0:TZ_1";
- reg = <0x19a0000 0x0280000>;
- read-only;
- };
-
- partition@1c20000 {
- label = "0:RPM_1";
- reg = <0x1c20000 0x0280000>;
- read-only;
- };
-
- partition@1ea0000 {
- label = "0:BOOTCONFIG1";
- reg = <0x1ea0000 0x0060000>;
- read-only;
- };
-
- partition@1f00000 {
- label = "0:APPSBL_1";
- reg = <0x1f00000 0x0500000>;
- read-only;
- };
-
- partition@2400000 {
- label = "ubi";
- reg = <0x2400000 0x1a000000>;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_WAN;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_AMBER>;
- function = LED_FUNCTION_WAN;
- default-state = "keep";
- };
- };
- };
-
- port@2 {
- reg = <2>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_AMBER>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
- };
- };
-
- port@3 {
- reg = <3>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_AMBER>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
- };
- };
-
- port@4 {
- reg = <4>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_AMBER>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
- };
- };
-
- port@5 {
- reg = <5>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
-
- leds {
- #address-cells = <1>;
- #size-cells = <0>;
-
- led@0 {
- reg = <0>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_AMBER>;
- function = LED_FUNCTION_LAN;
- default-state = "keep";
- };
- };
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac0 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
-
- nvmem-cells = <&macaddr_ART_0>;
- nvmem-cell-names = "mac-address";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <1>;
-
- nvmem-cells = <&macaddr_ART_6>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi0: wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&precal_ART_1000>;
- nvmem-cell-names = "pre-calibration";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi1: wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&precal_ART_5000>;
- nvmem-cell-names = "pre-calibration";
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later
-
-#include "qcom-ipq8065-smb208.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Arris TR4400 v2";
- compatible = "arris,tr4400-v2", "qcom,ipq8065", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- aliases {
- led-boot = &led_status_blue;
- led-failsafe = &led_status_red;
- led-running = &led_status_blue;
- led-upgrade = &led_status_red;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_status_red: status_red {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_RED>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- led_status_blue: status_blue {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_BLUE>;
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&qcom_pinmux {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- rgmii2_pins: rgmii2-pins {
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32";
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi@1a280000 {
- status = "okay";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "everspin,mr25h256";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- qcom,boot-partitions = <0x0 0x1180000 0x5340000 0x10c0000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "0:SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
- partition@40000 {
- label = "0:MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
- partition@180000 {
- label = "0:SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
- partition@2c0000 {
- label = "0:SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
- partition@540000 {
- label = "0:DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
- partition@660000 {
- label = "0:SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
- partition@780000 {
- label = "0:TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
- partition@a00000 {
- label = "0:RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
- partition@c80000 {
- label = "0:APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
- partition@1180000 {
- label = "0:APPSBLENV";
- reg = <0x1180000 0x0080000>;
- };
- partition@1200000 {
- label = "0:ART";
- reg = <0x1200000 0x0140000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_ART_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
- precal_ART_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
- stock_partition@1340000 {
- label = "stock_rootfs";
- reg = <0x1340000 0x4000000>;
-
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "extra";
- reg = <0x0 0x4000000>;
- };
- };
- partition@5340000 {
- label = "0:BOOTCONFIG";
- reg = <0x5340000 0x0060000>;
- read-only;
- };
- partition@53a0000 {
- label = "0:SBL2_1";
- reg = <0x53a0000 0x0140000>;
- read-only;
- };
- partition@54e0000 {
- label = "0:SBL3_1";
- reg = <0x54e0000 0x0280000>;
- read-only;
- };
- partition@5760000 {
- label = "0:DDRCONFIG_1";
- reg = <0x5760000 0x0120000>;
- read-only;
- };
- partition@5880000 {
- label = "0:SSD_1";
- reg = <0x5880000 0x0120000>;
- read-only;
- };
- partition@59a0000 {
- label = "0:TZ_1";
- reg = <0x59a0000 0x0280000>;
- read-only;
- };
- partition@5c20000 {
- label = "0:RPM_1";
- reg = <0x5c20000 0x0280000>;
- read-only;
- };
- partition@5ea0000 {
- label = "0:BOOTCONFIG1";
- reg = <0x5ea0000 0x0060000>;
- read-only;
- };
- partition@5f00000 {
- label = "0:APPSBL_1";
- reg = <0x5f00000 0x0500000>;
- read-only;
- };
- stock_partition@6400000 {
- label = "stock_rootfs_1";
- reg = <0x6400000 0x4000000>;
-
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "fw_env";
- reg = <0x0 0x100000>;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_fw_env_0: macaddr@0 {
- reg = <0x00 0x6>;
- };
- macaddr_fw_env_6: macaddr@6 {
- reg = <0x06 0x6>;
- };
- macaddr_fw_env_c: macaddr@c {
- reg = <0x0c 0x6>;
- };
- macaddr_fw_env_12: macaddr@12 {
- reg = <0x12 0x6>;
- };
- macaddr_fw_env_18: macaddr@18 {
- reg = <0x18 0x6>;
- };
- };
- };
-
- partition@100000 {
- label = "ubi";
- reg = <0x100000 0x9b00000>;
- };
- };
- stock_partition@a400000 {
- label = "stock_fw_env";
- reg = <0xa400000 0x0100000>;
- };
- stock_partition@a500000 {
- label = "stock_config";
- reg = <0xa500000 0x0800000>;
- };
- stock_partition@ad00000 {
- label = "stock_PKI";
- reg = <0xad00000 0x0200000>;
- };
- stock_partition@af00000 {
- label = "stock_scfgmgr";
- reg = <0xaf00000 0x0100000>;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
- };
- };
-
- phy7: ethernet-phy@7 {
- reg = <7>;
- };
-};
-
-&gmac0 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <0>;
-
- nvmem-cells = <&macaddr_fw_env_18>;
- nvmem-cell-names = "mac-address";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac1 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <1>;
-
- nvmem-cells = <&macaddr_fw_env_0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac3 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <3>;
- phy-handle = <&phy7>;
-
- nvmem-cells = <&macaddr_fw_env_6>;
- nvmem-cell-names = "mac-address";
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi0: wifi@1,0 {
- compatible = "pci168c,0046";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&precal_ART_1000>, <&macaddr_fw_env_12>;
- nvmem-cell-names = "pre-calibration", "mac-address";
- };
- };
-};
-
-&pcie1 {
- status = "okay";
- reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- max-link-speed = <1>;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi1: wifi@1,0 {
- compatible = "pci168c,0040";
- reg = <0x00010000 0 0 0 0>;
-
- nvmem-cells = <&precal_ART_5000>, <&macaddr_fw_env_c>;
- nvmem-cell-names = "pre-calibration", "mac-address";
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8065-nighthawk.dtsi"
-
-/ {
- model = "Netgear Nighthawk XR450";
- compatible = "netgear,xr450", "qcom,ipq8065", "qcom,ipq8064";
-
-};
-
-&leds {
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&partitions {
- partition@1880000 {
- label = "ubi";
- reg = <0x1880000 0xce00000>;
- };
-
- partition@e680000 {
- label = "reserve";
- reg = <0xe680000 0x0780000>;
- read-only;
- };
-};
-
-&wifi0 {
- nvmem-cells = <&macaddr_art_c>, <&precal_art_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
-
-&wifi1 {
- nvmem-cells = <&macaddr_art_0>, <&precal_art_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8065-nighthawk.dtsi"
-
-/ {
- model = "Netgear Nighthawk XR500";
- compatible = "netgear,xr500", "qcom,ipq8065", "qcom,ipq8064";
-
-};
-
-&leds {
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&partitions {
- partition@1880000 {
- label = "ubi";
- reg = <0x1880000 0xce00000>;
- };
-
- partition@e680000 {
- label = "reserve";
- reg = <0xe680000 0x0780000>;
- read-only;
- };
-};
-
-&wifi0 {
- nvmem-cells = <&macaddr_art_c>, <&precal_art_1000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
-
-&wifi1 {
- nvmem-cells = <&macaddr_art_0>, <&precal_art_5000>;
- nvmem-cell-names = "mac-address", "pre-calibration";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "qcom-ipq8064-v2.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- model = "Extreme Networks AP3935";
- compatible = "extreme,ap3935", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x41400000 0x3ec00000>;
- device_type = "memory";
- };
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi2_serial;
- mdio-gpio0 = &mdio0;
- ethernet0 = &gmac0;
- ethernet1 = &gmac2;
-
- led-boot = &led_power_green;
- led-failsafe = &led_power_orange;
- led-running = &led_power_green;
- led-upgrade = &led_power_green;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- bootargs-override = "ubi.block=0,0 root=/dev/ubiblock0_0";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_power_green: power_green {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>;
- };
-
- led_power_orange: power_orange {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_ORANGE>;
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
- };
-
- led_wlan2g_green {
- label = "green:wlan2g";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "phy0tpt";
- };
-
- led_wlan5g_green {
- label = "green:wlan5g";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "phy1tpt";
- };
-
- led_lan1_green {
- label = "green:lan1";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- led_lan1_orange {
- label = "orange:lan1";
- gpios = <&qcom_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- led_lan2_green {
- label = "green:lan2";
- gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
- };
-
- led_lan2_orange {
- label = "orange:lan2";
- gpios = <&qcom_pinmux 29 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-
-&qcom_pinmux {
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19";
- function = "gsbi5";
- drive-strength = <10>;
- bias-pull-down;
- };
-
- clk {
- pins = "gpio21";
- function = "gsbi5";
- drive-strength = <12>;
- bias-pull-down;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio22", "gpio23", "gpio24", "gpio25",
- "gpio26", "gpio27", "gpio28", "gpio29";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio56";
- function = "gpio";
- bias-pull-up;
- };
- };
-};
-
-&gsbi2 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
-
- gsbi2_serial: serial@12490000 {
- status = "okay";
- };
-};
-
-&gsbi4 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
-
- serial@16340000 {
- status = "disabled";
- };
-};
-
-&gsbi7 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
-
- gsbi7_serial: serial@16640000 {
- status = "okay";
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- cfg1@2a0000 {
- compatible = "u-boot,env-redundant-bool";
- label = "CFG1";
- reg = <0x2a0000 0x0010000>;
-
- ethaddr: ethaddr {
- #nvmem-cell-cells = <1>;
- };
- };
-
- bootpri@2b0000 {
- label = "BootPRI";
- reg = <0x2b0000 0x0080000>;
- };
-
- cfg2@330000 {
- label = "CFG2";
- reg = <0x330000 0x0010000>;
- };
-
- fs@340000 {
- label = "FS";
- reg = <0x340000 0x0080000>;
- };
-
- priimg@3c0000 {
- label = "PriImg";
- reg = <0x3c0000 0x0e10000>;
- };
-
- secimg@11d0000 {
- label = "SecImg";
- reg = <0x11d0000 0x0e10000>;
- };
- };
- };
- };
-};
-
-&pcie0 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- };
- };
-};
-
-&nand {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- compatible = "qcom,nandcs";
-
- reg = <0>;
-
- nand-ecc-strength = <8>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- ubi@0 {
- label = "ubi";
- reg = <0x0000000 0x20000000>;
- };
- };
- };
-};
-
-&soc {
- mdio1: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
-
- phy2: ethernet-phy@2 {
- reg = <2>;
- };
- };
-};
-
-&gmac0 {
- status = "okay";
-
- qcom,id = <0>;
- mdiobus = <&mdio1>;
-
- phy-mode = "rgmii";
- phy-handle = <&phy1>;
-
- nvmem-cells = <ðaddr 0>;
- nvmem-cell-names = "mac-address";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- qcom,id = <2>;
- mdiobus = <&mdio1>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy2>;
-
- nvmem-cells = <ðaddr 1>;
- nvmem-cell-names = "mac-address";
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-/ {
- memory {
- device_type = "memory";
- linux,usable-memory = <0x41500000 0x1ea00000>;
- reg = <0x40000000 0x20000000>;
- };
-
- cpus {
- idle-states {
- CPU_SPC: spc {
- status = "disabled";
- };
- };
- };
-
- chosen {
- bootargs-append = " console=ttyMSM0,115200n8 ubi.mtd=ubi ubi.mtd=art";
- };
-};
-
-&qcom_pinmux {
- mdio0_pins_active: mdio0_pins_active {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <2>;
- bias-pull-down;
- output-low;
- };
-
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- phy_active: phy_active {
- phy {
- pins = "gpio6", "gpio7";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- output-high;
- };
- };
-
- uart1_pins: uart1_pins {
- mux {
- pins = "gpio51", "gpio52";
- function = "gsbi1";
- drive-strength = <4>;
- bias-disable;
- };
- };
-};
-
-&gsbi1 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
-
- serial@12450000 {
- status = "okay";
-
- pinctrl-0 = <&uart1_pins>;
- pinctrl-names = "default";
- };
-};
-
-&pcie0 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x0 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi0: wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x10000 0 0 0 0>;
- };
- };
-};
-
-&pcie1 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x0 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi1: wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x10000 0 0 0 0>;
- };
- };
-};
-
-&pcie2 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x0 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi2: wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x10000 0 0 0 0>;
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- compatible = "qcom,nandcs";
-
- reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x2140000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "sbl1";
- reg = <0x0 0x40000>;
- read-only;
- };
-
- partition@40000 {
- label = "mibib";
- reg = <0x40000 0x140000>;
- read-only;
- };
-
- partition@180000 {
- label = "sbl2";
- reg = <0x180000 0x140000>;
- read-only;
- };
-
- partition@2c0000 {
- label = "sbl3";
- reg = <0x2c0000 0x280000>;
- read-only;
- };
-
- partition@540000 {
- label = "ddrconfig";
- reg = <0x540000 0x120000>;
- read-only;
- };
-
- partition@660000 {
- label = "ssd";
- reg = <0x660000 0x120000>;
- read-only;
- };
-
- partition@780000 {
- label = "tz";
- reg = <0x780000 0x280000>;
- read-only;
- };
-
- partition@a00000 {
- label = "rpm";
- reg = <0xa00000 0x280000>;
- read-only;
- };
-
- partition@1fc0000 {
- label = "u-boot";
- reg = <0x1fc0000 0x180000>;
- read-only;
- };
-
- partition@21c0000 {
- label = "bootkernel1";
- reg = <0x21c0000 0xa80000>;
- };
-
- partition@2c40000 {
- label = "bootkernel2";
- reg = <0x2c40000 0xa80000>;
- };
-
- partition@36c0000 {
- label = "ubi";
- reg = <0x36c0000 0x46c0000>;
- };
-
- partition@7d80000 {
- label = "art";
- reg = <0x7d80000 0x200000>;
- read-only;
- };
- };
- };
-};
+++ /dev/null
-#include "qcom-ipq8064-v2.0-smb208.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- model = "Edgecore ECW5410";
- compatible = "edgecore,ecw5410", "qcom,ipq8064";
-
- reserved-memory {
- nss@40000000 {
- reg = <0x40000000 0x1000000>;
- no-map;
- };
-
- smem: smem@41000000 {
- reg = <0x41000000 0x200000>;
- no-map;
- };
-
- wifi_dump@44000000 {
- reg = <0x44000000 0x600000>;
- no-map;
- };
- };
-
- cpus {
- idle-states {
- CPU_SPC: spc {
- status = "disabled";
- };
- };
- };
-
- aliases {
- serial1 = &gsbi1_serial;
- ethernet0 = &gmac2;
- ethernet1 = &gmac3;
-
- led-boot = &led_power_green;
- led-failsafe = &led_power_red;
- led-running = &led_power_green;
- led-upgrade = &led_power_green;
- };
-
- chosen {
- bootargs-append = " console=ttyMSM0,115200n8 root=/dev/ubiblock0_1";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_power_green: power_green {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g_green {
- label = "green:wlan2g";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
- };
-
- wlan2g_yellow {
- label = "yellow:wlan2g";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
- };
-
- wlan5g_green {
- label = "green:wlan5g";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- led_power_red: power_red {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
- };
-
- wlan5g_yellow {
- label = "yellow:wlan5g";
- gpios = <&qcom_pinmux 59 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-
-&qcom_pinmux {
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19";
- function = "gsbi5";
- drive-strength = <10>;
- bias-pull-down;
- };
-
- clk {
- pins = "gpio21";
- function = "gsbi5";
- drive-strength = <12>;
- bias-pull-down;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio16", "gpio23", "gpio24", "gpio26",
- "gpio28", "gpio59";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- uart1_pins: uart1_pins {
- mux {
- pins = "gpio51", "gpio52", "gpio53", "gpio54";
- function = "gsbi1";
- drive-strength = <12>;
- bias-none;
- };
- };
-};
-
-&gsbi1 {
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- status = "okay";
-
- serial@12450000 {
- status = "okay";
-
- pinctrl-0 = <&uart1_pins>;
- pinctrl-names = "default";
- };
-};
-
-&gsbi5 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
-
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- partitions {
- compatible = "qcom,smem-part";
- };
- };
- };
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
- };
- };
-};
-
-&pcie2 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-
- bridge@0,0 {
- reg = <0x00000000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- wifi@1,0 {
- compatible = "qcom,ath10k";
- status = "okay";
- reg = <0x00010000 0 0 0 0>;
- qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
- };
- };
-};
-
-&nand {
- status = "okay";
-
- nand@0 {
- compatible = "qcom,nandcs";
-
- reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- rootfs1@0 {
- label = "rootfs1";
- reg = <0x0000000 0x4000000>;
- };
-
- rootfs2@4000000 {
- label = "rootfs2";
- reg = <0x4000000 0x4000000>;
- };
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- qcom,id = <2>;
- mdiobus = <&mdio0>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy1>;
-};
-
-&gmac3 {
- status = "okay";
-
- qcom,id = <3>;
- mdiobus = <&mdio0>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy0>;
-};
-
-&adm_dma {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-
-#include "qcom-ipq8068-cryptid-common.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Meraki MR42";
- compatible = "meraki,mr42", "qcom,ipq8064";
-
- aliases {
- serial1 = &gsbi1_serial;
- ethernet0 = &gmac3;
-
- led-boot = &led_active;
- led-failsafe = &led_power;
- led-running = &led_active;
- led-upgrade = &led_active;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_ORANGE>;
- gpios = <&qcom_pinmux 31 GPIO_ACTIVE_HIGH>;
- };
-
- led_active: active {
- label = "white:active";
- gpios = <&qcom_pinmux 32 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&gmac3 {
- status = "okay";
-
- qcom,id = <3>;
- mdiobus = <&mdio0>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy2>;
-
- nvmem-cells = <&mac_address 0>;
- nvmem-cell-names = "mac-address";
-};
-
-&gsbi2 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
-};
-
-&gsbi2_i2c {
- status = "okay";
-
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
-
- ina2xx@40 {
- compatible = "ina219";
- shunt-resistor = <40000>;
- reg = <0x40>;
- };
-
- eeprom@56 {
- compatible = "atmel,24c64";
- pagesize = <32>;
- reg = <0x56>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- mac_address: mac-address@66 {
- compatible = "mac-base";
- reg = <0x66 0x6>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-};
-
-&gsbi6 {
- qcom,mode = <GSBI_PROT_I2C>;
- status = "okay";
-};
-
-&gsbi6_i2c {
- status = "okay";
-
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
-
- tlc591xx@40 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "ti,tlc59108";
- reg = <0x40>;
-
- red@0 {
- label = "red:user";
- reg = <0x0>;
- };
-
- green@1 {
- label = "green:user";
- reg = <0x1>;
- };
-
- blue@2 {
- label = "blue:user";
- reg = <0x2>;
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins_active>, <&phy_active>;
- pinctrl-names = "default";
-
- phy2: ethernet-phy2 {
- reg = <2>;
-
- reset-gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- reset-assert-us = <24000>;
-
- eee-broken-100tx;
- eee-broken-1000t;
- };
-};
-
-&qcom_pinmux {
- i2c0_pins: i2c0_pins {
- mux {
- pins = "gpio24", "gpio25";
- function = "gsbi2";
- drive-strength = <2>;
- bias-pull-up;
- input;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio26";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c1_pins: i2c1_pins {
- mux {
- pins = "gpio29", "gpio30";
- function = "gsbi6";
- drive-strength = <2>;
- bias-pull-up;
- input;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio31", "gpio32";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-low;
- };
- };
-};
-
-&wifi0 {
- nvmem-cells = <&mac_address 1>;
- nvmem-cell-names = "mac-address";
-};
-
-&wifi1 {
- nvmem-cells = <&mac_address 2>;
- nvmem-cell-names = "mac-address";
-};
-
-&wifi2 {
- nvmem-cells = <&mac_address 3>;
- nvmem-cell-names = "mac-address";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-
-#include "qcom-ipq8068-cryptid-common.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Meraki MR52";
- compatible = "meraki,mr52", "qcom,ipq8064";
-
- aliases {
- serial1 = &gsbi1_serial;
- mdio-gpio0 = &mdio_gpio0;
- ethernet0 = &gmac2;
- ethernet1 = &gmac3;
-
- led-boot = &led_active;
- led-failsafe = &led_power;
- led-running = &led_active;
- led-upgrade = &led_active;
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- led_power: power {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_ORANGE>;
- gpios = <&qcom_pinmux 19 GPIO_ACTIVE_HIGH>;
- };
-
- lan2_green {
- label = "green:lan2";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- lan1_green {
- label = "green:lan1";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- led_active: active {
- label = "white:active";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- lan2_orange {
- label = "orange:lan2";
- gpios = <&qcom_pinmux 60 GPIO_ACTIVE_HIGH>;
- };
-
- lan1_orange {
- label = "orange:lan1";
- gpios = <&qcom_pinmux 62 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&gmac2 {
- status = "okay";
-
- qcom,id = <2>;
- mdiobus = <&mdio0>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy0>;
-
- nvmem-cells = <&mac_address 0>;
- nvmem-cell-names = "mac-address";
-};
-
-&gmac3 {
- status = "okay";
-
- qcom,id = <3>;
- mdiobus = <&mdio_gpio0>;
-
- phy-mode = "sgmii";
- phy-handle = <&phy4>;
-
- nvmem-cells = <&mac_address 1>;
- nvmem-cell-names = "mac-address";
-};
-
-&gsbi7 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
-};
-
-&gsbi7_i2c {
- status = "okay";
-
- pinctrl-0 = <&i2c_pins>;
- pinctrl-names = "default";
-
- ina2xx@45 {
- compatible = "ina219";
- shunt-resistor = <80000>;
- reg = <0x45>;
- };
-
- tlc591xx@49 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "ti,tlc59108";
- reg = <0x49>;
-
- red@0 {
- label = "red:user";
- reg = <0x0>;
- };
-
- green@1 {
- label = "green:user";
- reg = <0x1>;
- };
-
- blue@2 {
- label = "blue:user";
- reg = <0x2>;
- };
- };
-
- eeprom@52 {
- compatible = "atmel,24c64";
- pagesize = <32>;
- reg = <0x52>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- mac_address: mac-address@66 {
- compatible = "mac-base";
- reg = <0x66 0x6>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-};
-
-&qcom_pinmux {
- i2c_pins: i2c_pins {
- mux {
- pins = "gpio8", "gpio9";
- function = "gsbi7";
- drive-strength = <2>;
- bias-pull-up;
- input;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio19", "gpio26";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-low;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- input;
- };
- };
-};
-
-&soc {
- mdio_gpio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins_active>, <&phy_active>;
- pinctrl-names = "default";
-
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH
- &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
-
- phy0: ethernet-phy0 {
- reg = <0>;
- reset-gpios = <&qcom_pinmux 7 GPIO_ACTIVE_LOW>;
- reset-assert-us = <24000>;
- };
-
- phy4: ethernet-phy4 {
- reg = <4>;
- reset-gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- reset-assert-us = <24000>;
- };
- };
-};
-
-&wifi0 {
- nvmem-cells = <&mac_address 4>;
- nvmem-cell-names = "mac-address";
-};
-
-&wifi1 {
- nvmem-cells = <&mac_address 3>;
- nvmem-cell-names = "mac-address";
-};
-
-&wifi2 {
- nvmem-cells = <&mac_address 2>;
- nvmem-cell-names = "mac-address";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-};
-
-&usb3_1 {
- status = "okay";
-};
+++ /dev/null
-From 09be1a39e685d8c5edd471fd1cac9a8f8280d2de Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Tue, 8 Nov 2022 22:17:34 +0100
-Subject: [PATCH] clk: qcom: kpss-xcc: register it as clk provider
-
-krait-cc use this driver for the secondary mux. Register it as a clk
-provider to correctly use this clk in other drivers.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221108211734.3707-1-ansuelsmth@gmail.com
----
- drivers/clk/qcom/kpss-xcc.c | 13 +++++++++----
- 1 file changed, 9 insertions(+), 4 deletions(-)
-
---- a/drivers/clk/qcom/kpss-xcc.c
-+++ b/drivers/clk/qcom/kpss-xcc.c
-@@ -31,12 +31,13 @@ MODULE_DEVICE_TABLE(of, kpss_xcc_match_t
-
- static int kpss_xcc_driver_probe(struct platform_device *pdev)
- {
-+ struct device *dev = &pdev->dev;
- const struct of_device_id *id;
- void __iomem *base;
- struct clk_hw *hw;
- const char *name;
-
-- id = of_match_device(kpss_xcc_match_table, &pdev->dev);
-+ id = of_match_device(kpss_xcc_match_table, dev);
- if (!id)
- return -ENODEV;
-
-@@ -45,7 +46,7 @@ static int kpss_xcc_driver_probe(struct
- return PTR_ERR(base);
-
- if (id->data) {
-- if (of_property_read_string_index(pdev->dev.of_node,
-+ if (of_property_read_string_index(dev->of_node,
- "clock-output-names",
- 0, &name))
- return -ENODEV;
-@@ -55,12 +56,16 @@ static int kpss_xcc_driver_probe(struct
- base += 0x28;
- }
-
-- hw = devm_clk_hw_register_mux_parent_data_table(&pdev->dev, name, aux_parents,
-+ hw = devm_clk_hw_register_mux_parent_data_table(dev, name, aux_parents,
- ARRAY_SIZE(aux_parents), 0,
- base, 0, 0x3,
- 0, aux_parent_map, NULL);
-+ if (IS_ERR(hw))
-+ return PTR_ERR(hw);
-
-- return PTR_ERR_OR_ZERO(hw);
-+ of_clk_add_hw_provider(dev->of_node, of_clk_hw_simple_get, hw);
-+
-+ return 0;
- }
-
- static struct platform_driver kpss_xcc_driver = {
+++ /dev/null
-From 3198106a99e73dbc4c02bd5128cec0997c73af82 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Tue, 8 Nov 2022 22:58:27 +0100
-Subject: [PATCH 1/6] clk: qcom: krait-cc: use devm variant for clk notifier
- register
-
-Use devm variant for clk notifier register and correctly handle free
-resource on driver remove.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221108215827.30475-1-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -62,7 +62,7 @@ static int krait_notifier_register(struc
- int ret = 0;
-
- mux->clk_nb.notifier_call = krait_notifier_cb;
-- ret = clk_notifier_register(clk, &mux->clk_nb);
-+ ret = devm_clk_notifier_register(dev, clk, &mux->clk_nb);
- if (ret)
- dev_err(dev, "failed to register clock notifier: %d\n", ret);
-
+++ /dev/null
-From 8e456411abcbf899c04740b9dbb3dcefcd61c946 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 9 Nov 2022 01:56:27 +0100
-Subject: [PATCH 2/6] clk: qcom: krait-cc: fix wrong parent order for secondary
- mux
-
-The secondary mux parent order is swapped.
-This currently doesn't cause problems as the secondary mux is used for idle
-clk and as a safe clk source while reprogramming the hfpll.
-
-Each mux have 2 or more output but he always have a safe source to
-switch while reprogramming the connected pll. We use a clk notifier to
-switch to the correct parent before clk core can apply the correct rate.
-The parent to switch is hardcoded in the mux struct.
-
-For the secondary mux the safe source to use is the qsb parent as it's
-the only fixed clk as the acpus_aux is a pll that can source from pxo or
-from pll8.
-
-The hardcoded safe parent for the secondary mux is set to index 0 that
-in the secondary mux map is set to 2.
-
-But the index 0 is actually acpu_aux in the parent list.
-
-Fix the swapped parents to correctly handle idle frequency and output a
-sane clk_summary report.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221109005631.3189-1-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -116,8 +116,8 @@ krait_add_sec_mux(struct device *dev, in
- int ret;
- struct krait_mux_clk *mux;
- static const char *sec_mux_list[] = {
-- "acpu_aux",
- "qsb",
-+ "acpu_aux",
- };
- struct clk_init_data init = {
- .parent_names = sec_mux_list,
+++ /dev/null
-From 18ae57b1e8abee6c453381470f6e18991d2901a8 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 9 Nov 2022 01:56:28 +0100
-Subject: [PATCH 3/6] clk: qcom: krait-cc: also enable secondary mux and div
- clk
-
-clk-krait ignore any rate change if clk is not flagged as enabled.
-Correctly enable the secondary mux and div clk to correctly change rate
-instead of silently ignoring the request.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221109005631.3189-2-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 21 ++++++++++++++++++++-
- 1 file changed, 20 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -80,6 +80,7 @@ krait_add_div(struct device *dev, int id
- };
- const char *p_names[1];
- struct clk *clk;
-+ int cpu;
-
- div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
- if (!div)
-@@ -103,6 +104,17 @@ krait_add_div(struct device *dev, int id
- }
-
- clk = devm_clk_register(dev, &div->hw);
-+ if (IS_ERR(clk))
-+ goto err;
-+
-+ /* clk-krait ignore any rate change if mux is not flagged as enabled */
-+ if (id < 0)
-+ for_each_online_cpu(cpu)
-+ clk_prepare_enable(div->hw.clk);
-+ else
-+ clk_prepare_enable(div->hw.clk);
-+
-+err:
- kfree(p_names[0]);
- kfree(init.name);
-
-@@ -113,7 +125,7 @@ static int
- krait_add_sec_mux(struct device *dev, int id, const char *s,
- unsigned int offset, bool unique_aux)
- {
-- int ret;
-+ int cpu, ret;
- struct krait_mux_clk *mux;
- static const char *sec_mux_list[] = {
- "qsb",
-@@ -165,6 +177,13 @@ krait_add_sec_mux(struct device *dev, in
- if (ret)
- goto unique_aux;
-
-+ /* clk-krait ignore any rate change if mux is not flagged as enabled */
-+ if (id < 0)
-+ for_each_online_cpu(cpu)
-+ clk_prepare_enable(mux->hw.clk);
-+ else
-+ clk_prepare_enable(mux->hw.clk);
-+
- unique_aux:
- if (unique_aux)
- kfree(sec_mux_list[0]);
+++ /dev/null
-From e5dc1a4c01510da8438dddfdf4200b79d73990dc Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 9 Nov 2022 01:56:29 +0100
-Subject: [PATCH 4/6] clk: qcom: krait-cc: handle secondary mux sourcing out of
- acpu_aux
-
-Some bootloader may leave the system in an even more undefined state
-with the secondary mux of L2 or other cores sourcing out of the acpu_aux
-parent. This results in the clk set to the PXO rate or a PLL8 rate.
-
-The current logic to reset the mux and set them to a defined state only
-handle if the mux are configured to source out of QSB. Change this and
-force a new and defined state if the current clk is lower than the aux
-rate. This way we can handle any wrong configuration where the mux is
-sourcing out of QSB (rate 225MHz, currently set to a virtual rate of 1),
-PXO rate (rate 25MHz) or PLL8 (needs to be configured to run at 384Mhz).
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221109005631.3189-3-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -383,8 +383,8 @@ static int krait_cc_probe(struct platfor
- */
- cur_rate = clk_get_rate(l2_pri_mux_clk);
- aux_rate = 384000000;
-- if (cur_rate == 1) {
-- pr_info("L2 @ QSB rate. Forcing new rate.\n");
-+ if (cur_rate < aux_rate) {
-+ pr_info("L2 @ Undefined rate. Forcing new rate.\n");
- cur_rate = aux_rate;
- }
- clk_set_rate(l2_pri_mux_clk, aux_rate);
-@@ -394,8 +394,8 @@ static int krait_cc_probe(struct platfor
- for_each_possible_cpu(cpu) {
- clk = clks[cpu];
- cur_rate = clk_get_rate(clk);
-- if (cur_rate == 1) {
-- pr_info("CPU%d @ QSB rate. Forcing new rate.\n", cpu);
-+ if (cur_rate < aux_rate) {
-+ pr_info("CPU%d @ Undefined rate. Forcing new rate.\n", cpu);
- cur_rate = aux_rate;
- }
-
+++ /dev/null
-From 8ea9fb841a7e528bc8ae79d726ce951dcf7b46e2 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 9 Nov 2022 01:56:30 +0100
-Subject: [PATCH 5/6] clk: qcom: krait-cc: convert to devm_clk_hw_register
-
-clk_register is now deprecated. Convert the driver to devm_clk_hw_register.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221109005631.3189-4-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 31 +++++++++++++++++++------------
- 1 file changed, 19 insertions(+), 12 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -79,8 +79,7 @@ krait_add_div(struct device *dev, int id
- .flags = CLK_SET_RATE_PARENT,
- };
- const char *p_names[1];
-- struct clk *clk;
-- int cpu;
-+ int cpu, ret;
-
- div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
- if (!div)
-@@ -103,8 +102,8 @@ krait_add_div(struct device *dev, int id
- return -ENOMEM;
- }
-
-- clk = devm_clk_register(dev, &div->hw);
-- if (IS_ERR(clk))
-+ ret = devm_clk_hw_register(dev, &div->hw);
-+ if (ret)
- goto err;
-
- /* clk-krait ignore any rate change if mux is not flagged as enabled */
-@@ -118,7 +117,7 @@ err:
- kfree(p_names[0]);
- kfree(init.name);
-
-- return PTR_ERR_OR_ZERO(clk);
-+ return ret;
- }
-
- static int
-@@ -137,7 +136,6 @@ krait_add_sec_mux(struct device *dev, in
- .ops = &krait_mux_clk_ops,
- .flags = CLK_SET_RATE_PARENT,
- };
-- struct clk *clk;
-
- mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
- if (!mux)
-@@ -166,14 +164,16 @@ krait_add_sec_mux(struct device *dev, in
- if (unique_aux) {
- sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
- if (!sec_mux_list[0]) {
-- clk = ERR_PTR(-ENOMEM);
-+ ret = -ENOMEM;
- goto err_aux;
- }
- }
-
-- clk = devm_clk_register(dev, &mux->hw);
-+ ret = devm_clk_hw_register(dev, &mux->hw);
-+ if (ret)
-+ goto unique_aux;
-
-- ret = krait_notifier_register(dev, clk, mux);
-+ ret = krait_notifier_register(dev, mux->hw.clk, mux);
- if (ret)
- goto unique_aux;
-
-@@ -189,7 +189,7 @@ unique_aux:
- kfree(sec_mux_list[0]);
- err_aux:
- kfree(init.name);
-- return PTR_ERR_OR_ZERO(clk);
-+ return ret;
- }
-
- static struct clk *
-@@ -241,11 +241,18 @@ krait_add_pri_mux(struct device *dev, in
- goto err_p2;
- }
-
-- clk = devm_clk_register(dev, &mux->hw);
-+ ret = devm_clk_hw_register(dev, &mux->hw);
-+ if (ret) {
-+ clk = ERR_PTR(ret);
-+ goto err_p3;
-+ }
-+
-+ clk = mux->hw.clk;
-
- ret = krait_notifier_register(dev, clk, mux);
- if (ret)
-- goto err_p3;
-+ clk = ERR_PTR(ret);
-+
- err_p3:
- kfree(p_names[2]);
- err_p2:
+++ /dev/null
-From 56a655e1c41a86445cf2de656649ad93424b2a63 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 9 Nov 2022 01:56:31 +0100
-Subject: [PATCH 6/6] clk: qcom: krait-cc: convert to parent_data API
-
-Modernize the krait-cc driver to parent-data API and refactor to drop
-any use of parent_names. From Documentation all the required clocks should
-be declared in DTS so fw_name can be correctly used to get the parents
-for all the muxes. .name is also declared to save compatibility with old
-DT.
-
-While at it also drop some hardcoded index and introduce an enum to make
-index values more clear.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221109005631.3189-5-ansuelsmth@gmail.com
----
- drivers/clk/qcom/krait-cc.c | 202 ++++++++++++++++++++----------------
- 1 file changed, 112 insertions(+), 90 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -15,6 +15,16 @@
-
- #include "clk-krait.h"
-
-+enum {
-+ cpu0_mux = 0,
-+ cpu1_mux,
-+ cpu2_mux,
-+ cpu3_mux,
-+ l2_mux,
-+
-+ clks_max,
-+};
-+
- static unsigned int sec_mux_map[] = {
- 2,
- 0,
-@@ -69,21 +79,23 @@ static int krait_notifier_register(struc
- return ret;
- }
-
--static int
-+static struct clk_hw *
- krait_add_div(struct device *dev, int id, const char *s, unsigned int offset)
- {
- struct krait_div2_clk *div;
-+ static struct clk_parent_data p_data[1];
- struct clk_init_data init = {
-- .num_parents = 1,
-+ .num_parents = ARRAY_SIZE(p_data),
- .ops = &krait_div2_clk_ops,
- .flags = CLK_SET_RATE_PARENT,
- };
-- const char *p_names[1];
-+ struct clk_hw *clk;
-+ char *parent_name;
- int cpu, ret;
-
- div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
- if (!div)
-- return -ENOMEM;
-+ return ERR_PTR(-ENOMEM);
-
- div->width = 2;
- div->shift = 6;
-@@ -93,18 +105,25 @@ krait_add_div(struct device *dev, int id
-
- init.name = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
- if (!init.name)
-- return -ENOMEM;
-+ return ERR_PTR(-ENOMEM);
-
-- init.parent_names = p_names;
-- p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
-- if (!p_names[0]) {
-- kfree(init.name);
-- return -ENOMEM;
-+ init.parent_data = p_data;
-+ parent_name = kasprintf(GFP_KERNEL, "hfpll%s", s);
-+ if (!parent_name) {
-+ clk = ERR_PTR(-ENOMEM);
-+ goto err_parent_name;
- }
-
-+ p_data[0].fw_name = parent_name;
-+ p_data[0].name = parent_name;
-+
- ret = devm_clk_hw_register(dev, &div->hw);
-- if (ret)
-- goto err;
-+ if (ret) {
-+ clk = ERR_PTR(ret);
-+ goto err_clk;
-+ }
-+
-+ clk = &div->hw;
-
- /* clk-krait ignore any rate change if mux is not flagged as enabled */
- if (id < 0)
-@@ -113,33 +132,36 @@ krait_add_div(struct device *dev, int id
- else
- clk_prepare_enable(div->hw.clk);
-
--err:
-- kfree(p_names[0]);
-+err_clk:
-+ kfree(parent_name);
-+err_parent_name:
- kfree(init.name);
-
-- return ret;
-+ return clk;
- }
-
--static int
-+static struct clk_hw *
- krait_add_sec_mux(struct device *dev, int id, const char *s,
- unsigned int offset, bool unique_aux)
- {
- int cpu, ret;
- struct krait_mux_clk *mux;
-- static const char *sec_mux_list[] = {
-- "qsb",
-- "acpu_aux",
-+ static struct clk_parent_data sec_mux_list[2] = {
-+ { .name = "qsb", .fw_name = "qsb" },
-+ {},
- };
- struct clk_init_data init = {
-- .parent_names = sec_mux_list,
-+ .parent_data = sec_mux_list,
- .num_parents = ARRAY_SIZE(sec_mux_list),
- .ops = &krait_mux_clk_ops,
- .flags = CLK_SET_RATE_PARENT,
- };
-+ struct clk_hw *clk;
-+ char *parent_name;
-
- mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
- if (!mux)
-- return -ENOMEM;
-+ return ERR_PTR(-ENOMEM);
-
- mux->offset = offset;
- mux->lpl = id >= 0;
-@@ -159,23 +181,33 @@ krait_add_sec_mux(struct device *dev, in
-
- init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
- if (!init.name)
-- return -ENOMEM;
-+ return ERR_PTR(-ENOMEM);
-
- if (unique_aux) {
-- sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
-- if (!sec_mux_list[0]) {
-- ret = -ENOMEM;
-+ parent_name = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
-+ if (!parent_name) {
-+ clk = ERR_PTR(-ENOMEM);
- goto err_aux;
- }
-+ sec_mux_list[1].fw_name = parent_name;
-+ sec_mux_list[1].name = parent_name;
-+ } else {
-+ sec_mux_list[1].name = "apu_aux";
- }
-
- ret = devm_clk_hw_register(dev, &mux->hw);
-- if (ret)
-- goto unique_aux;
-+ if (ret) {
-+ clk = ERR_PTR(ret);
-+ goto err_clk;
-+ }
-+
-+ clk = &mux->hw;
-
- ret = krait_notifier_register(dev, mux->hw.clk, mux);
-- if (ret)
-- goto unique_aux;
-+ if (ret) {
-+ clk = ERR_PTR(ret);
-+ goto err_clk;
-+ }
-
- /* clk-krait ignore any rate change if mux is not flagged as enabled */
- if (id < 0)
-@@ -184,28 +216,29 @@ krait_add_sec_mux(struct device *dev, in
- else
- clk_prepare_enable(mux->hw.clk);
-
--unique_aux:
-+err_clk:
- if (unique_aux)
-- kfree(sec_mux_list[0]);
-+ kfree(parent_name);
- err_aux:
- kfree(init.name);
-- return ret;
-+ return clk;
- }
-
--static struct clk *
--krait_add_pri_mux(struct device *dev, int id, const char *s,
-- unsigned int offset)
-+static struct clk_hw *
-+krait_add_pri_mux(struct device *dev, struct clk_hw *hfpll_div, struct clk_hw *sec_mux,
-+ int id, const char *s, unsigned int offset)
- {
- int ret;
- struct krait_mux_clk *mux;
-- const char *p_names[3];
-+ static struct clk_parent_data p_data[3];
- struct clk_init_data init = {
-- .parent_names = p_names,
-- .num_parents = ARRAY_SIZE(p_names),
-+ .parent_data = p_data,
-+ .num_parents = ARRAY_SIZE(p_data),
- .ops = &krait_mux_clk_ops,
- .flags = CLK_SET_RATE_PARENT,
- };
-- struct clk *clk;
-+ struct clk_hw *clk;
-+ char *hfpll_name;
-
- mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
- if (!mux)
-@@ -223,55 +256,44 @@ krait_add_pri_mux(struct device *dev, in
- if (!init.name)
- return ERR_PTR(-ENOMEM);
-
-- p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
-- if (!p_names[0]) {
-+ hfpll_name = kasprintf(GFP_KERNEL, "hfpll%s", s);
-+ if (!hfpll_name) {
- clk = ERR_PTR(-ENOMEM);
-- goto err_p0;
-+ goto err_hfpll;
- }
-
-- p_names[1] = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
-- if (!p_names[1]) {
-- clk = ERR_PTR(-ENOMEM);
-- goto err_p1;
-- }
-+ p_data[0].fw_name = hfpll_name;
-+ p_data[0].name = hfpll_name;
-
-- p_names[2] = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
-- if (!p_names[2]) {
-- clk = ERR_PTR(-ENOMEM);
-- goto err_p2;
-- }
-+ p_data[1].hw = hfpll_div;
-+ p_data[2].hw = sec_mux;
-
- ret = devm_clk_hw_register(dev, &mux->hw);
- if (ret) {
- clk = ERR_PTR(ret);
-- goto err_p3;
-+ goto err_clk;
- }
-
-- clk = mux->hw.clk;
-+ clk = &mux->hw;
-
-- ret = krait_notifier_register(dev, clk, mux);
-+ ret = krait_notifier_register(dev, mux->hw.clk, mux);
- if (ret)
- clk = ERR_PTR(ret);
-
--err_p3:
-- kfree(p_names[2]);
--err_p2:
-- kfree(p_names[1]);
--err_p1:
-- kfree(p_names[0]);
--err_p0:
-+err_clk:
-+ kfree(hfpll_name);
-+err_hfpll:
- kfree(init.name);
- return clk;
- }
-
- /* id < 0 for L2, otherwise id == physical CPU number */
--static struct clk *krait_add_clks(struct device *dev, int id, bool unique_aux)
-+static struct clk_hw *krait_add_clks(struct device *dev, int id, bool unique_aux)
- {
-- int ret;
-+ struct clk_hw *hfpll_div, *sec_mux, *pri_mux;
- unsigned int offset;
- void *p = NULL;
- const char *s;
-- struct clk *clk;
-
- if (id >= 0) {
- offset = 0x4501 + (0x1000 * id);
-@@ -283,22 +305,23 @@ static struct clk *krait_add_clks(struct
- s = "_l2";
- }
-
-- ret = krait_add_div(dev, id, s, offset);
-- if (ret) {
-- clk = ERR_PTR(ret);
-+ hfpll_div = krait_add_div(dev, id, s, offset);
-+ if (IS_ERR(hfpll_div)) {
-+ pri_mux = hfpll_div;
- goto err;
- }
-
-- ret = krait_add_sec_mux(dev, id, s, offset, unique_aux);
-- if (ret) {
-- clk = ERR_PTR(ret);
-+ sec_mux = krait_add_sec_mux(dev, id, s, offset, unique_aux);
-+ if (IS_ERR(sec_mux)) {
-+ pri_mux = sec_mux;
- goto err;
- }
-
-- clk = krait_add_pri_mux(dev, id, s, offset);
-+ pri_mux = krait_add_pri_mux(dev, hfpll_div, sec_mux, id, s, offset);
-+
- err:
- kfree(p);
-- return clk;
-+ return pri_mux;
- }
-
- static struct clk *krait_of_get(struct of_phandle_args *clkspec, void *data)
-@@ -306,7 +329,7 @@ static struct clk *krait_of_get(struct o
- unsigned int idx = clkspec->args[0];
- struct clk **clks = data;
-
-- if (idx >= 5) {
-+ if (idx >= clks_max) {
- pr_err("%s: invalid clock index %d\n", __func__, idx);
- return ERR_PTR(-EINVAL);
- }
-@@ -327,9 +350,8 @@ static int krait_cc_probe(struct platfor
- const struct of_device_id *id;
- unsigned long cur_rate, aux_rate;
- int cpu;
-- struct clk *clk;
-- struct clk **clks;
-- struct clk *l2_pri_mux_clk;
-+ struct clk_hw *mux, *l2_pri_mux;
-+ struct clk *clk, **clks;
-
- id = of_match_device(krait_cc_match_table, dev);
- if (!id)
-@@ -348,21 +370,21 @@ static int krait_cc_probe(struct platfor
- }
-
- /* Krait configurations have at most 4 CPUs and one L2 */
-- clks = devm_kcalloc(dev, 5, sizeof(*clks), GFP_KERNEL);
-+ clks = devm_kcalloc(dev, clks_max, sizeof(*clks), GFP_KERNEL);
- if (!clks)
- return -ENOMEM;
-
- for_each_possible_cpu(cpu) {
-- clk = krait_add_clks(dev, cpu, id->data);
-+ mux = krait_add_clks(dev, cpu, id->data);
- if (IS_ERR(clk))
- return PTR_ERR(clk);
-- clks[cpu] = clk;
-+ clks[cpu] = mux->clk;
- }
-
-- l2_pri_mux_clk = krait_add_clks(dev, -1, id->data);
-- if (IS_ERR(l2_pri_mux_clk))
-- return PTR_ERR(l2_pri_mux_clk);
-- clks[4] = l2_pri_mux_clk;
-+ l2_pri_mux = krait_add_clks(dev, -1, id->data);
-+ if (IS_ERR(l2_pri_mux))
-+ return PTR_ERR(l2_pri_mux);
-+ clks[l2_mux] = l2_pri_mux->clk;
-
- /*
- * We don't want the CPU or L2 clocks to be turned off at late init
-@@ -372,7 +394,7 @@ static int krait_cc_probe(struct platfor
- * they take over.
- */
- for_each_online_cpu(cpu) {
-- clk_prepare_enable(l2_pri_mux_clk);
-+ clk_prepare_enable(clks[l2_mux]);
- WARN(clk_prepare_enable(clks[cpu]),
- "Unable to turn on CPU%d clock", cpu);
- }
-@@ -388,16 +410,16 @@ static int krait_cc_probe(struct platfor
- * two different rates to force a HFPLL reinit under all
- * circumstances.
- */
-- cur_rate = clk_get_rate(l2_pri_mux_clk);
-+ cur_rate = clk_get_rate(clks[l2_mux]);
- aux_rate = 384000000;
- if (cur_rate < aux_rate) {
- pr_info("L2 @ Undefined rate. Forcing new rate.\n");
- cur_rate = aux_rate;
- }
-- clk_set_rate(l2_pri_mux_clk, aux_rate);
-- clk_set_rate(l2_pri_mux_clk, 2);
-- clk_set_rate(l2_pri_mux_clk, cur_rate);
-- pr_info("L2 @ %lu KHz\n", clk_get_rate(l2_pri_mux_clk) / 1000);
-+ clk_set_rate(clks[l2_mux], aux_rate);
-+ clk_set_rate(clks[l2_mux], 2);
-+ clk_set_rate(clks[l2_mux], cur_rate);
-+ pr_info("L2 @ %lu KHz\n", clk_get_rate(clks[l2_mux]) / 1000);
- for_each_possible_cpu(cpu) {
- clk = clks[cpu];
- cur_rate = clk_get_rate(clk);
+++ /dev/null
-From c9713e4ede1e5d044b64fe4d3cbb84223625637f Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Tue, 25 Oct 2022 01:38:17 +0200
-Subject: [PATCH] ARM: dts: qcom: ipq8064: disable mmc-ddr-1_8v for sdcc1
-
-It was reported non working mmc with this option enabled.
-Both mmc for ipq8064 are supplied by a fixed 3.3v regulator so mmc can't
-be run at 1.8v.
-Disable it to restore correct functionality of this SoC feature.
-
-Tested-by: Hendrik Koerner <koerhen@web.de>
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221024233817.27410-1-ansuelsmth@gmail.com
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -756,7 +756,6 @@
- non-removable;
- cap-sd-highspeed;
- cap-mmc-highspeed;
-- mmc-ddr-1_8v;
- vmmc-supply = <&vsdcc_fixed>;
- dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
- dma-names = "tx", "rx";
+++ /dev/null
-From de48d8766afcd97d147699aaff78a338081c9973 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Sat, 22 Oct 2022 14:56:55 +0200
-Subject: [PATCH 1/3] thermal/drivers/qcom/tsens: Init debugfs only with
- successful probe
-
-Calibrate and tsens_register can fail or PROBE_DEFER. This will cause a
-double or a wrong init of the debugfs information. Init debugfs only
-with successful probe fixing warning about directory already present.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
-Link: https://lore.kernel.org/r/20221022125657.22530-2-ansuelsmth@gmail.com
-Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
----
- drivers/thermal/qcom/tsens.c | 8 +++++---
- 1 file changed, 5 insertions(+), 3 deletions(-)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -918,8 +918,6 @@ int __init init_common(struct tsens_priv
- if (tsens_version(priv) >= VER_0_1)
- tsens_enable_irq(priv);
-
-- tsens_debug_init(op);
--
- err_put_device:
- put_device(&op->dev);
- return ret;
-@@ -1156,7 +1154,11 @@ static int tsens_probe(struct platform_d
- }
- }
-
-- return tsens_register(priv);
-+ ret = tsens_register(priv);
-+ if (!ret)
-+ tsens_debug_init(pdev);
-+
-+ return ret;
- }
-
- static int tsens_remove(struct platform_device *pdev)
+++ /dev/null
-From c7e077e921fa94e0c06c8d14af6c0504c8a5f4bd Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Sat, 22 Oct 2022 14:56:56 +0200
-Subject: [PATCH 2/3] thermal/drivers/qcom/tsens: Fix wrong version id
- dbg_version_show
-
-For VER_0 the version was incorrectly reported as 0.1.0.
-
-Fix that and correctly report the major version for this old tsens
-revision.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Link: https://lore.kernel.org/r/20221022125657.22530-3-ansuelsmth@gmail.com
-Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
----
- drivers/thermal/qcom/tsens.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -692,7 +692,7 @@ static int dbg_version_show(struct seq_f
- return ret;
- seq_printf(s, "%d.%d.%d\n", maj_ver, min_ver, step_ver);
- } else {
-- seq_puts(s, "0.1.0\n");
-+ seq_printf(s, "0.%d.0\n", priv->feat->ver_major);
- }
-
- return 0;
+++ /dev/null
-From 89992d95ed1046338c7866ef7bbe6de543a2af91 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Sat, 22 Oct 2022 14:56:57 +0200
-Subject: [PATCH 3/3] thermal/drivers/qcom/tsens: Rework debugfs file structure
-
-The current tsens debugfs structure is composed by:
-- a tsens dir in debugfs with a version file
-- a directory for each tsens istance with sensors file to dump all the
- sensors value.
-
-This works on the assumption that we have the same version for each
-istance but this assumption seems fragile and with more than one tsens
-istance results in the version file not tracking each of them.
-
-A better approach is to just create a subdirectory for each tsens
-istance and put there version and sensors debugfs file.
-
-Using this new implementation results in less code since debugfs entry
-are created only on successful tsens probe.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Link: https://lore.kernel.org/r/20221022125657.22530-4-ansuelsmth@gmail.com
-Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
----
- drivers/thermal/qcom/tsens.c | 13 +++----------
- 1 file changed, 3 insertions(+), 10 deletions(-)
-
---- a/drivers/thermal/qcom/tsens.c
-+++ b/drivers/thermal/qcom/tsens.c
-@@ -704,21 +704,14 @@ DEFINE_SHOW_ATTRIBUTE(dbg_sensors);
- static void tsens_debug_init(struct platform_device *pdev)
- {
- struct tsens_priv *priv = platform_get_drvdata(pdev);
-- struct dentry *root, *file;
-
-- root = debugfs_lookup("tsens", NULL);
-- if (!root)
-+ priv->debug_root = debugfs_lookup("tsens", NULL);
-+ if (!priv->debug_root)
- priv->debug_root = debugfs_create_dir("tsens", NULL);
-- else
-- priv->debug_root = root;
--
-- file = debugfs_lookup("version", priv->debug_root);
-- if (!file)
-- debugfs_create_file("version", 0444, priv->debug_root,
-- pdev, &dbg_version_fops);
-
- /* A directory for each instance of the TSENS IP */
- priv->debug = debugfs_create_dir(dev_name(&pdev->dev), priv->debug_root);
-+ debugfs_create_file("version", 0444, priv->debug, pdev, &dbg_version_fops);
- debugfs_create_file("sensors", 0444, priv->debug, pdev, &dbg_sensors_fops);
- }
- #else
+++ /dev/null
-From 5001f2e1a325b68dbf225bd17f69a4d3d975cca5 Mon Sep 17 00:00:00 2001
-From: John Crispin <john@phrozen.org>
-Date: Thu, 9 Mar 2017 09:31:44 +0100
-Subject: [PATCH 61/69] mtd: "rootfs" conflicts with OpenWrt auto mounting
-
-Signed-off-by: John Crispin <john@phrozen.org>
----
- drivers/mtd/mtdpart.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/drivers/mtd/mtdpart.c
-+++ b/drivers/mtd/mtdpart.c
-@@ -51,7 +51,11 @@ static struct mtd_info *allocate_partiti
-
- /* allocate the partition structure */
- child = kzalloc(sizeof(*child), GFP_KERNEL);
-- name = kstrdup(part->name, GFP_KERNEL);
-+ /* "rootfs" conflicts with OpenWrt auto mounting */
-+ if (mtd_type_is_nand(parent) && !strcmp(part->name, "rootfs"))
-+ name = "ubi";
-+ else
-+ name = kstrdup(part->name, GFP_KERNEL);
- if (!name || !child) {
- printk(KERN_ERR"memory allocation error while creating partitions for \"%s\"\n",
- parent->name);
+++ /dev/null
-From bef5018abb7cf94efafdc05087b4c998891ae4ec Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Mon, 17 Jan 2022 23:39:34 +0100
-Subject: [PATCH v3 10/18] ARM: dts: qcom: add saw for l2 cache and kraitcc for
- ipq8064
-
-Add saw compatible for l2 cache and kraitcc node for ipq8064 dtsi.
-Also declare clock-output-names for acc0 and acc1 and qsb fixed clock
-for the secondary mux.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Tested-by: Jonathan McDowell <noodles@earth.li>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 34 +++++++++++++++++++++++++++--
- 1 file changed, 32 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -301,6 +301,12 @@
- };
-
- clocks {
-+ qsb: qsb {
-+ compatible = "fixed-clock";
-+ clock-frequency = <225000000>;
-+ #clock-cells = <0>;
-+ };
-+
- cxo_board: cxo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
-@@ -575,15 +581,30 @@
- clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
- clock-names = "pll8_vote", "pxo";
- clock-output-names = "acpu_l2_aux";
-+ #clock-cells = <0>;
-+ };
-+
-+ kraitcc: clock-controller {
-+ compatible = "qcom,krait-cc-v1";
-+ clocks = <&gcc PLL9>, <&gcc PLL10>, <&gcc PLL12>,
-+ <&acc0>, <&acc1>, <&l2cc>, <&qsb>, <&pxo_board>;
-+ clock-names = "hfpll0", "hfpll1", "hfpll_l2",
-+ "acpu0_aux", "acpu1_aux", "acpu_l2_aux",
-+ "qsb", "pxo";
-+ #clock-cells = <1>;
- };
-
- acc0: clock-controller@2088000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
-+ clock-output-names = "acpu0_aux";
-+ clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
-+ clock-names = "pll8_vote", "pxo";
-+ #clock-cells = <0>;
- };
-
- saw0: regulator@2089000 {
-- compatible = "qcom,saw2";
-+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
- reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-@@ -591,14 +612,24 @@
- acc1: clock-controller@2098000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
-+ clock-output-names = "acpu1_aux";
-+ clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
-+ clock-names = "pll8_vote", "pxo";
-+ #clock-cells = <0>;
- };
-
- saw1: regulator@2099000 {
-- compatible = "qcom,saw2";
-+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
- reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-
-+ saw_l2: regulator@02012000 {
-+ compatible = "qcom,saw2", "syscon";
-+ reg = <0x02012000 0x1000>;
-+ regulator;
-+ };
-+
- nss_common: syscon@03000000 {
- compatible = "syscon";
- reg = <0x03000000 0x0000FFFF>;
+++ /dev/null
-From 076ebb6e1799c4c7a1d2e07510d88b9e9b57b551 Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Tue, 18 Jan 2022 00:03:47 +0100
-Subject: [PATCH v3 13/18] ARM: dts: qcom: add opp table for cpu and l2 for
- ipq8064
-
-Add opp table for cpu and l2 cache. While the current cpufreq is
-the generic one that doesn't scale the L2 cache, we add the l2
-cache opp anyway for the sake of completeness. This will be handy in the
-future when a dedicated cpufreq driver is introduced for krait cores
-that will correctly scale l2 cache with the core freq.
-
-Opp-level is set based on the logic of
-0: idle level
-1: normal level
-2: turbo level
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Tested-by: Jonathan McDowell <noodles@earth.li>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 99 +++++++++++++++++++++++++++++
- 1 file changed, 99 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -48,6 +48,105 @@
- };
- };
-
-+ opp_table_l2: opp_table_l2 {
-+ compatible = "operating-points-v2";
-+
-+ opp-384000000 {
-+ opp-hz = /bits/ 64 <384000000>;
-+ opp-microvolt = <1100000>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <0>;
-+ };
-+
-+ opp-1000000000 {
-+ opp-hz = /bits/ 64 <1000000000>;
-+ opp-microvolt = <1100000>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <1>;
-+ };
-+
-+ opp-1200000000 {
-+ opp-hz = /bits/ 64 <1200000000>;
-+ opp-microvolt = <1150000>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <2>;
-+ };
-+ };
-+
-+ opp_table0: opp_table0 {
-+ compatible = "operating-points-v2-kryo-cpu";
-+ nvmem-cells = <&speedbin_efuse>;
-+
-+ /*
-+ * Voltage thresholds are <target min max>
-+ */
-+ opp-384000000 {
-+ opp-hz = /bits/ 64 <384000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>;
-+ opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>;
-+ opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>;
-+ opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <0>;
-+ };
-+
-+ opp-600000000 {
-+ opp-hz = /bits/ 64 <600000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>;
-+ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>;
-+ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>;
-+ opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <1>;
-+ };
-+
-+ opp-800000000 {
-+ opp-hz = /bits/ 64 <800000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>;
-+ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>;
-+ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <1>;
-+ };
-+
-+ opp-1000000000 {
-+ opp-hz = /bits/ 64 <1000000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>;
-+ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>;
-+ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <1>;
-+ };
-+
-+ opp-1200000000 {
-+ opp-hz = /bits/ 64 <1200000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>;
-+ opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>;
-+ opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>;
-+ opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <2>;
-+ };
-+
-+ opp-1400000000 {
-+ opp-hz = /bits/ 64 <1400000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>;
-+ opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>;
-+ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>;
-+ opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <2>;
-+ };
-+ };
-+
- thermal-zones {
- sensor0-thermal {
- polling-delay-passive = <0>;
---- a/arch/arm/boot/dts/qcom-ipq8065.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8065.dtsi
-@@ -6,3 +6,92 @@
- model = "Qualcomm Technologies, Inc. IPQ8065";
- compatible = "qcom,ipq8065", "qcom,ipq8064";
- };
-+
-+&opp_table_l2 {
-+ /delete-node/opp-1200000000;
-+
-+ opp-1400000000 {
-+ opp-hz = /bits/ 64 <1400000000>;
-+ opp-microvolt = <1150000>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <2>;
-+ };
-+};
-+
-+&opp_table0 {
-+ /*
-+ * On ipq8065 1.2 ghz freq is not present
-+ * Remove it to make cpufreq work and not
-+ * complain for missing definition
-+ */
-+
-+ /delete-node/opp-1200000000;
-+
-+ /*
-+ * Voltage thresholds are <target min max>
-+ */
-+ opp-384000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <975000 926250 1023750>;
-+ opp-microvolt-speed0-pvs1-v0 = <950000 902500 997500>;
-+ opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>;
-+ opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>;
-+ opp-microvolt-speed0-pvs4-v0 = <875000 831250 918750>;
-+ opp-microvolt-speed0-pvs5-v0 = <825000 783750 866250>;
-+ opp-microvolt-speed0-pvs6-v0 = <775000 736250 813750>;
-+ };
-+
-+ opp-600000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>;
-+ opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>;
-+ opp-microvolt-speed0-pvs2-v0 = <950000 902500 997500>;
-+ opp-microvolt-speed0-pvs3-v0 = <925000 878750 971250>;
-+ opp-microvolt-speed0-pvs4-v0 = <900000 855000 945000>;
-+ opp-microvolt-speed0-pvs5-v0 = <850000 807500 892500>;
-+ opp-microvolt-speed0-pvs6-v0 = <800000 760000 840000>;
-+ };
-+
-+ opp-800000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>;
-+ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs2-v0 = <1000000 950000 1050000>;
-+ opp-microvolt-speed0-pvs3-v0 = <975000 926250 1023750>;
-+ opp-microvolt-speed0-pvs4-v0 = <950000 902500 997500>;
-+ opp-microvolt-speed0-pvs5-v0 = <900000 855000 945000>;
-+ opp-microvolt-speed0-pvs6-v0 = <850000 807500 892500>;
-+ };
-+
-+ opp-1000000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>;
-+ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>;
-+ opp-microvolt-speed0-pvs2-v0 = <1050000 997500 1102500>;
-+ opp-microvolt-speed0-pvs3-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs4-v0 = <1000000 950000 1050000>;
-+ opp-microvolt-speed0-pvs5-v0 = <950000 902500 997500>;
-+ opp-microvolt-speed0-pvs6-v0 = <900000 855000 945000>;
-+ };
-+
-+ opp-1400000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1175000 1116250 1233750>;
-+ opp-microvolt-speed0-pvs1-v0 = <1150000 1092500 1207500>;
-+ opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>;
-+ opp-microvolt-speed0-pvs3-v0 = <1100000 1045000 1155000>;
-+ opp-microvolt-speed0-pvs4-v0 = <1075000 1021250 1128750>;
-+ opp-microvolt-speed0-pvs5-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs6-v0 = <975000 926250 1023750>;
-+ opp-level = <1>;
-+ };
-+
-+ opp-1725000000 {
-+ opp-hz = /bits/ 64 <1725000000>;
-+ opp-microvolt-speed0-pvs0-v0 = <1262500 1199375 1325625>;
-+ opp-microvolt-speed0-pvs1-v0 = <1225000 1163750 1286250>;
-+ opp-microvolt-speed0-pvs2-v0 = <1200000 1140000 1260000>;
-+ opp-microvolt-speed0-pvs3-v0 = <1175000 1116250 1233750>;
-+ opp-microvolt-speed0-pvs4-v0 = <1150000 1092500 1207500>;
-+ opp-microvolt-speed0-pvs5-v0 = <1100000 1045000 1155000>;
-+ opp-microvolt-speed0-pvs6-v0 = <1050000 997500 1102500>;
-+ opp-supported-hw = <0x1>;
-+ clock-latency-ns = <100000>;
-+ opp-level = <2>;
-+ };
-+};
---- a/arch/arm/boot/dts/qcom-ipq8062.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8062.dtsi
-@@ -6,3 +6,39 @@
- model = "Qualcomm Technologies, Inc. IPQ8062";
- compatible = "qcom,ipq8062", "qcom,ipq8064";
- };
-+
-+&opp_table0 {
-+ /delete-node/opp-1200000000;
-+ /delete-node/opp-1400000000;
-+
-+ /*
-+ * Voltage thresholds are <target min max>
-+ */
-+ opp-384000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>;
-+ opp-microvolt-speed0-pvs1-v0 = < 925000 878750 971250>;
-+ opp-microvolt-speed0-pvs2-v0 = < 875000 831250 918750>;
-+ opp-microvolt-speed0-pvs3-v0 = < 800000 760000 840000>;
-+ };
-+
-+ opp-600000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>;
-+ opp-microvolt-speed0-pvs1-v0 = < 975000 926250 1023750>;
-+ opp-microvolt-speed0-pvs2-v0 = < 925000 878750 971250>;
-+ opp-microvolt-speed0-pvs3-v0 = < 850000 807500 892500>;
-+ };
-+
-+ opp-800000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>;
-+ opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs2-v0 = < 995000 945250 1044750>;
-+ opp-microvolt-speed0-pvs3-v0 = < 900000 855000 945000>;
-+ };
-+
-+ opp-1000000000 {
-+ opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>;
-+ opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>;
-+ opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>;
-+ opp-microvolt-speed0-pvs3-v0 = < 950000 902500 997500>;
-+ };
-+};
+++ /dev/null
-From 211fc0c0a63c99b68663a27182e643316c2d8cbe Mon Sep 17 00:00:00 2001
-From: Ansuel Smith <ansuelsmth@gmail.com>
-Date: Tue, 18 Jan 2022 00:07:57 +0100
-Subject: [PATCH v3 15/18] ARM: dts: qcom: add multiple missing binding for cpu
- and l2 for ipq8064
-
-Add multiple binding for cpu node, l2 node and add idle-states
-definition for ipq8064 dtsi.
-
-Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
-Tested-by: Jonathan McDowell <noodles@earth.li>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 36 +++++++++++++++++++++++++++++
- 1 file changed, 36 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -30,6 +30,15 @@
- next-level-cache = <&L2>;
- qcom,acc = <&acc0>;
- qcom,saw = <&saw0>;
-+ clocks = <&kraitcc 0>, <&kraitcc 4>;
-+ clock-names = "cpu", "l2";
-+ clock-latency = <100000>;
-+ operating-points-v2 = <&opp_table0>;
-+ voltage-tolerance = <5>;
-+ cooling-min-state = <0>;
-+ cooling-max-state = <10>;
-+ #cooling-cells = <2>;
-+ cpu-idle-states = <&CPU_SPC>;
- };
-
- cpu1: cpu@1 {
-@@ -40,11 +49,35 @@
- next-level-cache = <&L2>;
- qcom,acc = <&acc1>;
- qcom,saw = <&saw1>;
-+ clocks = <&kraitcc 1>, <&kraitcc 4>;
-+ clock-names = "cpu", "l2";
-+ clock-latency = <100000>;
-+ operating-points-v2 = <&opp_table0>;
-+ voltage-tolerance = <5>;
-+ cooling-min-state = <0>;
-+ cooling-max-state = <10>;
-+ #cooling-cells = <2>;
-+ cpu-idle-states = <&CPU_SPC>;
-+ };
-+
-+ idle-states {
-+ CPU_SPC: spc {
-+ compatible = "qcom,idle-state-spc";
-+ status = "disabled";
-+ entry-latency-us = <400>;
-+ exit-latency-us = <900>;
-+ min-residency-us = <3000>;
-+ };
- };
-
- L2: l2-cache {
- compatible = "cache";
- cache-level = <2>;
-+ qcom,saw = <&saw_l2>;
-+
-+ clocks = <&kraitcc 4>;
-+ clock-names = "l2";
-+ operating-points-v2 = <&opp_table_l2>;
- };
- };
-
---- a/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi
-@@ -2,6 +2,18 @@
-
- #include "qcom-ipq8064.dtsi"
-
-+&cpu0 {
-+ cpu-supply = <&smb208_s2a>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&smb208_s2b>;
-+};
-+
-+&L2 {
-+ l2-supply = <&smb208_s1a>;
-+};
-+
- &rpm {
- smb208_regulators: regulators {
- compatible = "qcom,rpm-smb208-regulators";
---- a/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi
-@@ -2,6 +2,18 @@
-
- #include "qcom-ipq8064-v2.0.dtsi"
-
-+&cpu0 {
-+ cpu-supply = <&smb208_s2a>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&smb208_s2b>;
-+};
-+
-+&L2 {
-+ l2-supply = <&smb208_s1a>;
-+};
-+
- &rpm {
- smb208_regulators: regulators {
- compatible = "qcom,rpm-smb208-regulators";
---- a/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi
-@@ -2,6 +2,18 @@
-
- #include "qcom-ipq8062.dtsi"
-
-+&cpu0 {
-+ cpu-supply = <&smb208_s2a>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&smb208_s2b>;
-+};
-+
-+&L2 {
-+ l2-supply = <&smb208_s1a>;
-+};
-+
- &rpm {
- smb208_regulators: regulators {
- compatible = "qcom,rpm-smb208-regulators";
---- a/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi
-@@ -2,6 +2,18 @@
-
- #include "qcom-ipq8065.dtsi"
-
-+&cpu0 {
-+ cpu-supply = <&smb208_s2a>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&smb208_s2b>;
-+};
-+
-+&L2 {
-+ l2-supply = <&smb208_s1a>;
-+};
-+
- &rpm {
- smb208_regulators: regulators {
- compatible = "qcom,rpm-smb208-regulators";
+++ /dev/null
-From 6c94e0184e56f9e9f1f5d5f54b20758433e498d2 Mon Sep 17 00:00:00 2001
-From: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
-Date: Wed, 15 Jun 2022 16:47:09 +0200
-Subject: [PATCH 1/2] ARM: dts: qcom: fix wrong nad_pins definition for ipq806x
-
-Fix wrong nand_pings definition for bias-disable pins.
-
-Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 7 ++-----
- 1 file changed, 2 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -599,12 +599,9 @@
- };
-
- nand_pins: nand_pins {
-- mux {
-+ disable {
- pins = "gpio34", "gpio35", "gpio36",
-- "gpio37", "gpio38", "gpio39",
-- "gpio40", "gpio41", "gpio42",
-- "gpio43", "gpio44", "gpio45",
-- "gpio46", "gpio47";
-+ "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
+++ /dev/null
-From 504188183408fac0f61b59f5ed8ea1773fe43669 Mon Sep 17 00:00:00 2001
-From: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
-Date: Wed, 15 Jun 2022 16:59:30 +0200
-Subject: [PATCH 2/2] ARM: dts: qcom: add MDIO dedicated controller node for
- ipq806x
-
-Add MDIO dedicated controller attached to gmac0 and fix rb3011 dts to
-correctly use the new tag.
-
-Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
----
- arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 134 +++++++++++-----------
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 14 +++
- 2 files changed, 81 insertions(+), 67 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
-@@ -25,73 +25,6 @@
- device_type = "memory";
- };
-
-- mdio0: mdio-0 {
-- status = "okay";
-- compatible = "virtual,mdio-gpio";
-- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
-- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- pinctrl-0 = <&mdio0_pins>;
-- pinctrl-names = "default";
--
-- switch0: switch@10 {
-- compatible = "qca,qca8337";
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- dsa,member = <0 0>;
--
-- pinctrl-0 = <&sw0_reset_pin>;
-- pinctrl-names = "default";
--
-- reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
-- reg = <0x10>;
--
-- ports {
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- switch0cpu: port@0 {
-- reg = <0>;
-- label = "cpu";
-- ethernet = <&gmac0>;
-- phy-mode = "rgmii-id";
-- fixed-link {
-- speed = <1000>;
-- full-duplex;
-- };
-- };
--
-- port@1 {
-- reg = <1>;
-- label = "sw1";
-- };
--
-- port@2 {
-- reg = <2>;
-- label = "sw2";
-- };
--
-- port@3 {
-- reg = <3>;
-- label = "sw3";
-- };
--
-- port@4 {
-- reg = <4>;
-- label = "sw4";
-- };
--
-- port@5 {
-- reg = <5>;
-- label = "sw5";
-- };
-- };
-- };
-- };
--
- mdio1: mdio-1 {
- status = "okay";
- compatible = "virtual,mdio-gpio";
-@@ -222,6 +155,73 @@
- status = "okay";
- };
-
-+&mdio0 {
-+ status = "okay";
-+ compatible = "virtual,mdio-gpio";
-+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
-+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pinctrl-0 = <&mdio0_pins>;
-+ pinctrl-names = "default";
-+
-+ switch0: switch@10 {
-+ compatible = "qca,qca8337";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ dsa,member = <0 0>;
-+
-+ pinctrl-0 = <&sw0_reset_pin>;
-+ pinctrl-names = "default";
-+
-+ reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
-+ reg = <0x10>;
-+
-+ ports {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ switch0cpu: port@0 {
-+ reg = <0>;
-+ label = "cpu";
-+ ethernet = <&gmac0>;
-+ phy-mode = "rgmii-id";
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+
-+ port@1 {
-+ reg = <1>;
-+ label = "sw1";
-+ };
-+
-+ port@2 {
-+ reg = <2>;
-+ label = "sw2";
-+ };
-+
-+ port@3 {
-+ reg = <3>;
-+ label = "sw3";
-+ };
-+
-+ port@4 {
-+ reg = <4>;
-+ label = "sw4";
-+ };
-+
-+ port@5 {
-+ reg = <5>;
-+ label = "sw5";
-+ };
-+ };
-+ };
-+};
-+
- &gmac0 {
- status = "okay";
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -476,6 +476,20 @@
- snps,blen = <16 0 0 0 0 0 0>;
- };
-
-+ mdio0: mdio@37000000 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ compatible = "qcom,ipq8064-mdio", "syscon";
-+ reg = <0x37000000 0x200000>;
-+ resets = <&gcc GMAC_CORE1_RESET>;
-+ reset-names = "stmmaceth";
-+ clocks = <&gcc GMAC_CORE1_CLK>;
-+ clock-names = "stmmaceth";
-+
-+ status = "disabled";
-+ };
-+
- vsdcc_fixed: vsdcc-regulator {
- compatible = "regulator-fixed";
- regulator-name = "SDCC Power";
+++ /dev/null
-From b044ae89862132a86fb511648e9c52ea3cdf8c30 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 5 Aug 2020 14:19:23 +0200
-Subject: [PATCH 1/4] devfreq: qcom: Add L2 Krait Cache devfreq scaling driver
-
-Qcom L2 Krait CPUs use the generic cpufreq-dt driver and doesn't actually
-scale the Cache frequency when the CPU frequency is changed. This
-devfreq driver register with the cpu notifier and scale the Cache
-based on the max Freq across all core as the CPU cache is shared across
-all of them. If provided this also scale the voltage of the regulator
-attached to the CPU cache. The scaling logic is based on the CPU freq
-and the 3 scaling interval are set by the device dts.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/devfreq/Kconfig | 11 ++
- drivers/devfreq/Makefile | 1 +
- drivers/devfreq/krait-cache-devfreq.c | 188 ++++++++++++++++++++++++++
- 3 files changed, 200 insertions(+)
- create mode 100644 drivers/devfreq/krait-cache-devfreq.c
-
---- a/drivers/devfreq/Kconfig
-+++ b/drivers/devfreq/Kconfig
-@@ -151,6 +151,17 @@ config ARM_SUN8I_A33_MBUS_DEVFREQ
- This adds the DEVFREQ driver for the MBUS controller in some
- Allwinner sun8i (A33 through H3) and sun50i (A64 and H5) SoCs.
-
-+config ARM_KRAIT_CACHE_DEVFREQ
-+ tristate "Scaling support for Krait CPU Cache Devfreq"
-+ depends on ARCH_QCOM || COMPILE_TEST
-+ select DEVFREQ_GOV_PASSIVE
-+ help
-+ This adds the DEVFREQ driver for the Krait CPU L2 Cache shared by all cores.
-+
-+ The driver register with the cpufreq notifier and find the right frequency
-+ based on the max frequency across all core and the range set in the device
-+ dts. If provided this scale also the regulator attached to the l2 cache.
-+
- source "drivers/devfreq/event/Kconfig"
-
- endif # PM_DEVFREQ
---- a/drivers/devfreq/Makefile
-+++ b/drivers/devfreq/Makefile
-@@ -15,6 +15,7 @@ obj-$(CONFIG_ARM_MEDIATEK_CCI_DEVFREQ) +
- obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) += rk3399_dmc.o
- obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ) += sun8i-a33-mbus.o
- obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra30-devfreq.o
-+obj-$(CONFIG_ARM_KRAIT_CACHE_DEVFREQ) += krait-cache-devfreq.o
-
- # DEVFREQ Event Drivers
- obj-$(CONFIG_PM_DEVFREQ_EVENT) += event/
---- /dev/null
-+++ b/drivers/devfreq/krait-cache-devfreq.c
-@@ -0,0 +1,181 @@
-+// SPDX-License-Identifier: GPL-2.0
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/cpufreq.h>
-+#include <linux/devfreq.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/clk.h>
-+#include <linux/slab.h>
-+#include <linux/regulator/consumer.h>
-+#include <linux/pm_opp.h>
-+
-+#include "governor.h"
-+
-+struct krait_cache_data {
-+ struct clk *clk;
-+ unsigned long idle_freq;
-+ int token;
-+};
-+
-+static int krait_cache_config_clk(struct device *dev, struct opp_table *opp_table,
-+ struct dev_pm_opp *old_opp, struct dev_pm_opp *opp,
-+ void *data, bool scaling_down)
-+{
-+ struct krait_cache_data *kdata;
-+ unsigned long old_freq, freq;
-+ unsigned long idle_freq;
-+ struct clk *clk;
-+ int ret;
-+
-+ kdata = dev_get_drvdata(dev);
-+ idle_freq = kdata->idle_freq;
-+ clk = kdata->clk;
-+
-+ old_freq = dev_pm_opp_get_freq(old_opp);
-+ freq = dev_pm_opp_get_freq(opp);
-+
-+ /*
-+ * Set to idle bin if switching from normal to high bin
-+ * or vice versa. It has been notice that a bug is triggered
-+ * in cache scaling when more than one bin is scaled, to fix
-+ * this we first need to transition to the base rate and then
-+ * to target rate
-+ */
-+ if (likely(freq != idle_freq && old_freq != idle_freq)) {
-+ ret = clk_set_rate(clk, idle_freq);
-+ if (ret)
-+ return ret;
-+ }
-+
-+ return clk_set_rate(clk, freq);
-+};
-+
-+static int krait_cache_get_cur_freq(struct device *dev, unsigned long *freq)
-+{
-+ struct krait_cache_data *data = dev_get_drvdata(dev);
-+
-+ *freq = clk_get_rate(data->clk);
-+
-+ return 0;
-+};
-+
-+static int krait_cache_target(struct device *dev, unsigned long *freq,
-+ u32 flags)
-+{
-+ struct dev_pm_opp *opp;
-+
-+ opp = dev_pm_opp_find_freq_ceil(dev, freq);
-+ if (unlikely(IS_ERR(opp)))
-+ return PTR_ERR(opp);
-+
-+ dev_pm_opp_put(opp);
-+
-+ return dev_pm_opp_set_rate(dev, *freq);
-+};
-+
-+static int krait_cache_get_dev_status(struct device *dev,
-+ struct devfreq_dev_status *stat)
-+{
-+ struct krait_cache_data *data = dev_get_drvdata(dev);
-+
-+ stat->busy_time = 0;
-+ stat->total_time = 0;
-+ stat->current_frequency = clk_get_rate(data->clk);
-+
-+ return 0;
-+};
-+
-+static struct devfreq_dev_profile krait_cache_devfreq_profile = {
-+ .target = krait_cache_target,
-+ .get_dev_status = krait_cache_get_dev_status,
-+ .get_cur_freq = krait_cache_get_cur_freq
-+};
-+
-+static struct devfreq_passive_data devfreq_gov_data = {
-+ .parent_type = CPUFREQ_PARENT_DEV,
-+};
-+
-+static int krait_cache_probe(struct platform_device *pdev)
-+{
-+ struct dev_pm_opp_config config = { };
-+ struct device *dev = &pdev->dev;
-+ struct krait_cache_data *data;
-+ struct devfreq *devfreq;
-+ struct dev_pm_opp *opp;
-+ struct clk *clk;
-+ int ret, token;
-+
-+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
-+ if (!data)
-+ return -ENOMEM;
-+
-+ clk = devm_clk_get(dev, "l2");
-+ if (IS_ERR(clk))
-+ return PTR_ERR(clk);
-+
-+ config.regulator_names = (const char *[]){ "l2", NULL };
-+ config.clk_names = (const char *[]){ "l2", NULL };
-+ config.config_clks = krait_cache_config_clk;
-+
-+ token = dev_pm_opp_set_config(dev, &config);
-+ if (token < 0)
-+ return token;
-+
-+ ret = devm_pm_opp_of_add_table(dev);
-+ if (ret)
-+ goto free_opp;
-+
-+ opp = dev_pm_opp_find_freq_ceil(dev, &data->idle_freq);
-+ if (IS_ERR(opp)) {
-+ ret = PTR_ERR(opp);
-+ goto free_opp;
-+ }
-+ dev_pm_opp_put(opp);
-+
-+ data->token = token;
-+ data->clk = clk;
-+ dev_set_drvdata(dev, data);
-+ devfreq = devm_devfreq_add_device(dev, &krait_cache_devfreq_profile,
-+ DEVFREQ_GOV_PASSIVE, &devfreq_gov_data);
-+ if (IS_ERR(devfreq)) {
-+ ret = PTR_ERR(devfreq);
-+ goto free_opp;
-+ }
-+
-+ return 0;
-+
-+free_opp:
-+ dev_pm_opp_clear_config(token);
-+ return ret;
-+};
-+
-+static int krait_cache_remove(struct platform_device *pdev)
-+{
-+ struct krait_cache_data *data = dev_get_drvdata(&pdev->dev);
-+
-+ dev_pm_opp_clear_config(data->token);
-+
-+ return 0;
-+};
-+
-+static const struct of_device_id krait_cache_match_table[] = {
-+ { .compatible = "qcom,krait-cache" },
-+ {}
-+};
-+
-+static struct platform_driver krait_cache_driver = {
-+ .probe = krait_cache_probe,
-+ .remove = krait_cache_remove,
-+ .driver = {
-+ .name = "krait-cache-scaling",
-+ .of_match_table = krait_cache_match_table,
-+ },
-+};
-+module_platform_driver(krait_cache_driver);
-+
-+MODULE_DESCRIPTION("Krait CPU Cache Scaling driver");
-+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
-+MODULE_LICENSE("GPL v2");
+++ /dev/null
-From ef124ad0ff8abfbf4ebe3fe6d7dcef4541dec13a Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 16 Jun 2022 18:39:21 +0200
-Subject: [PATCH] ARM: dts: qcom: add krait-cache compatible for ipq806x dtsi
-
-Add qcom,krait-cache compatible to enable cache devfreq driver for
-ipq806x SoC and move the L2 node to the soc node to make the devfreq
-driver correctly probe.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 22 +++++++++++-----------
- 1 file changed, 11 insertions(+), 11 deletions(-)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -69,16 +69,6 @@
- min-residency-us = <3000>;
- };
- };
--
-- L2: l2-cache {
-- compatible = "cache";
-- cache-level = <2>;
-- qcom,saw = <&saw_l2>;
--
-- clocks = <&kraitcc 4>;
-- clock-names = "l2";
-- operating-points-v2 = <&opp_table_l2>;
-- };
- };
-
- opp_table_l2: opp_table_l2 {
-@@ -1409,6 +1399,16 @@
- #reset-cells = <1>;
- };
-
-+ L2: l2-cache {
-+ compatible = "cache", "qcom,krait-cache";
-+ cache-level = <2>;
-+ qcom,saw = <&saw_l2>;
-+
-+ clocks = <&kraitcc 4>;
-+ clock-names = "l2";
-+ operating-points-v2 = <&opp_table_l2>;
-+ };
-+
- lpass@28100000 {
- compatible = "qcom,lpass-cpu";
- status = "disabled";
+++ /dev/null
-From 13f075999935bb696dbab63243923179f06fa05e Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 16 Jun 2022 19:56:08 +0200
-Subject: [PATCH 3/4] devfreq: add ipq806x fabric scaling driver
-
-Add ipq806x fabric scaling driver using the devfreq passive governor.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/devfreq/Kconfig | 11 ++
- drivers/devfreq/Makefile | 1 +
- drivers/devfreq/ipq806x-fab-devfreq.c | 155 ++++++++++++++++++++++++++
- 3 files changed, 167 insertions(+)
- create mode 100644 drivers/devfreq/ipq806x-fab-devfreq.c
-
---- a/drivers/devfreq/Kconfig
-+++ b/drivers/devfreq/Kconfig
-@@ -162,6 +162,17 @@ config ARM_KRAIT_CACHE_DEVFREQ
- based on the max frequency across all core and the range set in the device
- dts. If provided this scale also the regulator attached to the l2 cache.
-
-+config ARM_IPQ806X_FAB_DEVFREQ
-+ tristate "Scaling support for ipq806x Soc Fabric"
-+ depends on ARCH_QCOM || COMPILE_TEST
-+ select DEVFREQ_GOV_PASSIVE
-+ help
-+ This adds the DEVFREQ driver for the ipq806x Soc Fabric.
-+
-+ The driver register with the cpufreq notifier and find the right frequency
-+ based on the max frequency across all core and the range set in the device
-+ dts.
-+
- source "drivers/devfreq/event/Kconfig"
-
- endif # PM_DEVFREQ
---- a/drivers/devfreq/Makefile
-+++ b/drivers/devfreq/Makefile
-@@ -16,6 +16,7 @@ obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) +=
- obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ) += sun8i-a33-mbus.o
- obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra30-devfreq.o
- obj-$(CONFIG_ARM_KRAIT_CACHE_DEVFREQ) += krait-cache-devfreq.o
-+obj-$(CONFIG_ARM_IPQ806X_FAB_DEVFREQ) += ipq806x-fab-devfreq.o
-
- # DEVFREQ Event Drivers
- obj-$(CONFIG_PM_DEVFREQ_EVENT) += event/
---- /dev/null
-+++ b/drivers/devfreq/ipq806x-fab-devfreq.c
-@@ -0,0 +1,155 @@
-+// SPDX-License-Identifier: GPL-2.0
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/cpufreq.h>
-+#include <linux/devfreq.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/clk.h>
-+#include <linux/slab.h>
-+#include <linux/pm_opp.h>
-+
-+#include "governor.h"
-+
-+struct ipq806x_fab_data {
-+ struct clk *fab_clk;
-+ struct clk *ddr_clk;
-+};
-+
-+static int ipq806x_fab_get_cur_freq(struct device *dev, unsigned long *freq)
-+{
-+ struct ipq806x_fab_data *data = dev_get_drvdata(dev);
-+
-+ *freq = clk_get_rate(data->fab_clk);
-+
-+ return 0;
-+};
-+
-+static int ipq806x_fab_target(struct device *dev, unsigned long *freq,
-+ u32 flags)
-+{
-+ struct ipq806x_fab_data *data = dev_get_drvdata(dev);
-+ struct dev_pm_opp *opp;
-+ int ret;
-+
-+ opp = dev_pm_opp_find_freq_ceil(dev, freq);
-+ if (unlikely(IS_ERR(opp)))
-+ return PTR_ERR(opp);
-+
-+ dev_pm_opp_put(opp);
-+
-+ ret = clk_set_rate(data->fab_clk, *freq);
-+ if (ret)
-+ return ret;
-+
-+ return clk_set_rate(data->ddr_clk, *freq);
-+};
-+
-+static int ipq806x_fab_get_dev_status(struct device *dev,
-+ struct devfreq_dev_status *stat)
-+{
-+ struct ipq806x_fab_data *data = dev_get_drvdata(dev);
-+
-+ stat->busy_time = 0;
-+ stat->total_time = 0;
-+ stat->current_frequency = clk_get_rate(data->fab_clk);
-+
-+ return 0;
-+};
-+
-+static struct devfreq_dev_profile ipq806x_fab_devfreq_profile = {
-+ .target = ipq806x_fab_target,
-+ .get_dev_status = ipq806x_fab_get_dev_status,
-+ .get_cur_freq = ipq806x_fab_get_cur_freq
-+};
-+
-+static struct devfreq_passive_data devfreq_gov_data = {
-+ .parent_type = CPUFREQ_PARENT_DEV,
-+};
-+
-+static int ipq806x_fab_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct ipq806x_fab_data *data;
-+ struct devfreq *devfreq;
-+ struct clk *clk;
-+ int ret;
-+
-+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
-+ if (!data)
-+ return -ENOMEM;
-+
-+ clk = devm_clk_get(dev, "apps-fab-clk");
-+ if (IS_ERR(clk)) {
-+ dev_err_probe(dev, PTR_ERR(clk), "failed to get apps fab clk\n");
-+ return PTR_ERR(clk);
-+ }
-+
-+ clk_prepare_enable(clk);
-+ data->fab_clk = clk;
-+
-+ clk = devm_clk_get(dev, "ddr-fab-clk");
-+ if (IS_ERR(clk)) {
-+ dev_err_probe(dev, PTR_ERR(clk), "failed to get ddr fab clk\n");
-+ goto err_ddr;
-+ }
-+
-+ clk_prepare_enable(clk);
-+ data->ddr_clk = clk;
-+
-+ ret = dev_pm_opp_of_add_table(dev);
-+ if (ret) {
-+ dev_err(dev, "failed to parse fab freq thresholds\n");
-+ return ret;
-+ }
-+
-+ dev_set_drvdata(dev, data);
-+
-+ devfreq = devm_devfreq_add_device(&pdev->dev, &ipq806x_fab_devfreq_profile,
-+ DEVFREQ_GOV_PASSIVE, &devfreq_gov_data);
-+ if (IS_ERR(devfreq))
-+ dev_pm_opp_remove_table(dev);
-+
-+ return PTR_ERR_OR_ZERO(devfreq);
-+
-+err_ddr:
-+ clk_unprepare(data->fab_clk);
-+ clk_put(data->fab_clk);
-+ return PTR_ERR(clk);
-+};
-+
-+static int ipq806x_fab_remove(struct platform_device *pdev)
-+{
-+ struct ipq806x_fab_data *data = dev_get_drvdata(&pdev->dev);
-+
-+ clk_unprepare(data->fab_clk);
-+ clk_put(data->fab_clk);
-+
-+ clk_unprepare(data->ddr_clk);
-+ clk_put(data->ddr_clk);
-+
-+ dev_pm_opp_remove_table(&pdev->dev);
-+
-+ return 0;
-+};
-+
-+static const struct of_device_id ipq806x_fab_match_table[] = {
-+ { .compatible = "qcom,fab-scaling" },
-+ {}
-+};
-+
-+static struct platform_driver ipq806x_fab_driver = {
-+ .probe = ipq806x_fab_probe,
-+ .remove = ipq806x_fab_remove,
-+ .driver = {
-+ .name = "ipq806x-fab-scaling",
-+ .of_match_table = ipq806x_fab_match_table,
-+ },
-+};
-+module_platform_driver(ipq806x_fab_driver);
-+
-+MODULE_DESCRIPTION("ipq806x Fab Scaling driver");
-+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
-+MODULE_LICENSE("GPL v2");
+++ /dev/null
-From c3573f0907dadb0a6e9933aae2a46a489abcbd48 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 16 Jun 2022 20:03:05 +0200
-Subject: [PATCH 4/4] ARM: dts: qcom: add fab scaling node for ipq806x
-
-Add fabric scaling node for ipq806x to correctly scale apps and ddr
-fabric clk.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- arch/arm/boot/dts/qcom-ipq8064.dtsi | 19 +++++++++++++++++++
- 1 file changed, 19 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
-+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -170,6 +170,18 @@
- };
- };
-
-+ opp_table_fab: opp_table_fab {
-+ compatible = "operating-points-v2";
-+
-+ opp-533000000 {
-+ opp-hz = /bits/ 64 <533000000>;
-+ };
-+
-+ opp-400000000 {
-+ opp-hz = /bits/ 64 <400000000>;
-+ };
-+ };
-+
- thermal-zones {
- sensor0-thermal {
- polling-delay-passive = <0>;
-@@ -1409,6 +1421,13 @@
- operating-points-v2 = <&opp_table_l2>;
- };
-
-+ fab-scaling {
-+ compatible = "qcom,fab-scaling";
-+ clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
-+ clock-names = "apps-fab-clk", "ddr-fab-clk";
-+ operating-points-v2 = <&opp_table_fab>;
-+ };
-+
- lpass@28100000 {
- compatible = "qcom,lpass-cpu";
- status = "disabled";
+++ /dev/null
-From 666c1b745e93ccddde841d5057c33f97b29a316a Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 15 Sep 2022 02:19:28 +0200
-Subject: [PATCH 3/9] clk: qcom: krait-cc: handle qsb clock defined in DTS
-
-qsb fixed clk may be defined in DTS and correctly passed in the clocks
-list. Add related code to handle this and modify the logic to
-dynamically read qsb clock frequency.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/krait-cc.c | 14 +++++++++++---
- 1 file changed, 11 insertions(+), 3 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -348,7 +348,7 @@ static int krait_cc_probe(struct platfor
- {
- struct device *dev = &pdev->dev;
- const struct of_device_id *id;
-- unsigned long cur_rate, aux_rate;
-+ unsigned long cur_rate, aux_rate, qsb_rate;
- int cpu;
- struct clk_hw *mux, *l2_pri_mux;
- struct clk *clk, **clks;
-@@ -357,11 +357,19 @@ static int krait_cc_probe(struct platfor
- if (!id)
- return -ENODEV;
-
-- /* Rate is 1 because 0 causes problems for __clk_mux_determine_rate */
-- clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, 1);
-+ /*
-+ * Per Documentation qsb should be provided from DTS.
-+ * To address old implementation, register the fixed clock anyway.
-+ * Rate is 1 because 0 causes problems for __clk_mux_determine_rate
-+ */
-+ clk = clk_get(dev, "qsb");
-+ if (IS_ERR(clk))
-+ clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, 1);
- if (IS_ERR(clk))
- return PTR_ERR(clk);
-
-+ qsb_rate = clk_get_rate(clk);
-+
- if (!id->data) {
- clk = clk_register_fixed_factor(dev, "acpu_aux",
- "gpll0_vote", 0, 1, 2);
+++ /dev/null
-From fca6f185a9d9ef0892a719bc6da955b22d326ec7 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 15 Sep 2022 02:24:33 +0200
-Subject: [PATCH 4/9] clk: qcom: krait-cc: register REAL qsb fixed clock
-
-With some tools it was discovered the real frequency of the qsb fixed
-clock. While not 100% correct it's still better than using 1 as a dummy
-frequency.
-Correctly register the qsb fixed clock with the frequency of 225 MHz
-instead of 1.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/krait-cc.c | 8 +++++---
- 1 file changed, 5 insertions(+), 3 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -25,6 +25,8 @@ enum {
- clks_max,
- };
-
-+#define QSB_RATE 2250000000
-+
- static unsigned int sec_mux_map[] = {
- 2,
- 0,
-@@ -364,7 +366,7 @@ static int krait_cc_probe(struct platfor
- */
- clk = clk_get(dev, "qsb");
- if (IS_ERR(clk))
-- clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, 1);
-+ clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, QSB_RATE);
- if (IS_ERR(clk))
- return PTR_ERR(clk);
-
+++ /dev/null
-From 2399d181557d94ae9a2686926cd25768f132e4b4 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Fri, 18 Mar 2022 16:12:14 +0100
-Subject: [PATCH 7/9] clk: qcom: krait-cc: drop pr_info and use dev_info
-
-Replace pr_info() with dev_info() to provide better diagnostics.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/krait-cc.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -423,25 +423,25 @@ static int krait_cc_probe(struct platfor
- cur_rate = clk_get_rate(clks[l2_mux]);
- aux_rate = 384000000;
- if (cur_rate < aux_rate) {
-- pr_info("L2 @ Undefined rate. Forcing new rate.\n");
-+ dev_info(dev, "L2 @ Undefined rate. Forcing new rate.\n");
- cur_rate = aux_rate;
- }
- clk_set_rate(clks[l2_mux], aux_rate);
- clk_set_rate(clks[l2_mux], 2);
- clk_set_rate(clks[l2_mux], cur_rate);
-- pr_info("L2 @ %lu KHz\n", clk_get_rate(clks[l2_mux]) / 1000);
-+ dev_info(dev, "L2 @ %lu KHz\n", clk_get_rate(clks[l2_mux]) / 1000);
- for_each_possible_cpu(cpu) {
- clk = clks[cpu];
- cur_rate = clk_get_rate(clk);
- if (cur_rate < aux_rate) {
-- pr_info("CPU%d @ Undefined rate. Forcing new rate.\n", cpu);
-+ dev_info(dev, "CPU%d @ Undefined rate. Forcing new rate.\n", cpu);
- cur_rate = aux_rate;
- }
-
- clk_set_rate(clk, aux_rate);
- clk_set_rate(clk, 2);
- clk_set_rate(clk, cur_rate);
-- pr_info("CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
-+ dev_info(dev, "CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
- }
-
- of_clk_add_provider(dev->of_node, krait_of_get, clks);
+++ /dev/null
-From 6a77cf3f5f95ec0058e1b4d1ada018748cb0b83b Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Thu, 15 Sep 2022 03:33:13 +0200
-Subject: [PATCH 9/9] clk: qcom: krait-cc: rework mux reset logic and reset
- hfpll
-
-Rework and clean mux reset logic.
-Compact it to a for loop to handle both CPU and L2 in one place.
-Move hardcoded aux_rate to define and add a new hfpll_rate value to
-reset hfpll settings.
-Change logic to now reset the hfpll to the lowest value of 600 Mhz and
-then restoring the previous frequency. This permits to reset the hfpll if
-the primary mux was set to source out of the secondary mux.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/krait-cc.c | 50 +++++++++++++++++--------------------
- 1 file changed, 23 insertions(+), 27 deletions(-)
-
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -25,7 +25,9 @@ enum {
- clks_max,
- };
-
--#define QSB_RATE 2250000000
-+#define QSB_RATE 225000000
-+#define AUX_RATE 384000000
-+#define HFPLL_RATE 600000000
-
- static unsigned int sec_mux_map[] = {
- 2,
-@@ -350,7 +352,7 @@ static int krait_cc_probe(struct platfor
- {
- struct device *dev = &pdev->dev;
- const struct of_device_id *id;
-- unsigned long cur_rate, aux_rate, qsb_rate;
-+ unsigned long cur_rate, qsb_rate;
- int cpu;
- struct clk_hw *mux, *l2_pri_mux;
- struct clk *clk, **clks;
-@@ -420,28 +422,29 @@ static int krait_cc_probe(struct platfor
- * two different rates to force a HFPLL reinit under all
- * circumstances.
- */
-- cur_rate = clk_get_rate(clks[l2_mux]);
-- aux_rate = 384000000;
-- if (cur_rate < aux_rate) {
-- dev_info(dev, "L2 @ Undefined rate. Forcing new rate.\n");
-- cur_rate = aux_rate;
-- }
-- clk_set_rate(clks[l2_mux], aux_rate);
-- clk_set_rate(clks[l2_mux], 2);
-- clk_set_rate(clks[l2_mux], cur_rate);
-- dev_info(dev, "L2 @ %lu KHz\n", clk_get_rate(clks[l2_mux]) / 1000);
-- for_each_possible_cpu(cpu) {
-+ for (cpu = 0; cpu < 5; cpu++) {
-+ const char *l2_s = "L2";
-+ char cpu_s[5];
-+
- clk = clks[cpu];
-+ if (!clk)
-+ continue;
-+
-+ if (cpu < 4)
-+ snprintf(cpu_s, 5, "CPU%d", cpu);
-+
- cur_rate = clk_get_rate(clk);
-- if (cur_rate < aux_rate) {
-- dev_info(dev, "CPU%d @ Undefined rate. Forcing new rate.\n", cpu);
-- cur_rate = aux_rate;
-+ if (cur_rate < AUX_RATE) {
-+ dev_info(dev, "%s @ Undefined rate. Forcing new rate.\n",
-+ cpu < 4 ? cpu_s : l2_s);
-+ cur_rate = AUX_RATE;
- }
-
-- clk_set_rate(clk, aux_rate);
-- clk_set_rate(clk, 2);
-+ clk_set_rate(clk, AUX_RATE);
-+ clk_set_rate(clk, HFPLL_RATE);
- clk_set_rate(clk, cur_rate);
-- dev_info(dev, "CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
-+ dev_info(dev, "%s @ %lu KHz\n", cpu < 4 ? cpu_s : l2_s,
-+ clk_get_rate(clk) / 1000);
- }
-
- of_clk_add_provider(dev->of_node, krait_of_get, clks);
+++ /dev/null
-From 908c361b3c3a139eb3e6a798cb620a6da7514d5c Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Fri, 23 Sep 2022 19:05:39 +0200
-Subject: [PATCH 2/4] clk: qcom: clk-krait: generilize div functions
-
-Generilize div functions and remove hardcode to a divisor of 2.
-This is just a cleanup and permit to make it more clear the settings of
-the devisor when used by the krait-cc driver.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/clk-krait.c | 57 ++++++++++++++++++++----------------
- drivers/clk/qcom/clk-krait.h | 11 ++++---
- drivers/clk/qcom/krait-cc.c | 7 +++--
- 3 files changed, 42 insertions(+), 33 deletions(-)
-
---- a/drivers/clk/qcom/clk-krait.c
-+++ b/drivers/clk/qcom/clk-krait.c
-@@ -97,53 +97,58 @@ const struct clk_ops krait_mux_clk_ops =
- EXPORT_SYMBOL_GPL(krait_mux_clk_ops);
-
- /* The divider can divide by 2, 4, 6 and 8. But we only really need div-2. */
--static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate,
-+static long krait_div_round_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *parent_rate)
- {
-- *parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw), rate * 2);
-- return DIV_ROUND_UP(*parent_rate, 2);
-+ struct krait_div_clk *d = to_krait_div_clk(hw);
-+
-+ *parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw),
-+ rate * d->divisor);
-+
-+ return DIV_ROUND_UP(*parent_rate, d->divisor);
- }
-
--static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate,
-+static int krait_div_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
- {
-- struct krait_div2_clk *d = to_krait_div2_clk(hw);
-+ struct krait_div_clk *d = to_krait_div_clk(hw);
-+ u8 div_val = krait_div_to_val(d->divisor);
- unsigned long flags;
-- u32 val;
-- u32 mask = BIT(d->width) - 1;
--
-- if (d->lpl)
-- mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift;
-- else
-- mask <<= d->shift;
-+ u32 regval;
-
- spin_lock_irqsave(&krait_clock_reg_lock, flags);
-- val = krait_get_l2_indirect_reg(d->offset);
-- val &= ~mask;
-- krait_set_l2_indirect_reg(d->offset, val);
-+ regval = krait_get_l2_indirect_reg(d->offset);
-+
-+ regval &= ~(d->mask << d->shift);
-+ regval |= (div_val & d->mask) << d->shift;
-+
-+ if (d->lpl) {
-+ regval &= ~(d->mask << (d->shift + LPL_SHIFT));
-+ regval |= (div_val & d->mask) << (d->shift + LPL_SHIFT);
-+ }
-+
-+ krait_set_l2_indirect_reg(d->offset, regval);
- spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
-
- return 0;
- }
-
- static unsigned long
--krait_div2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
-+krait_div_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
- {
-- struct krait_div2_clk *d = to_krait_div2_clk(hw);
-- u32 mask = BIT(d->width) - 1;
-+ struct krait_div_clk *d = to_krait_div_clk(hw);
- u32 div;
-
- div = krait_get_l2_indirect_reg(d->offset);
- div >>= d->shift;
-- div &= mask;
-- div = (div + 1) * 2;
-+ div &= d->mask;
-
-- return DIV_ROUND_UP(parent_rate, div);
-+ return DIV_ROUND_UP(parent_rate, krait_val_to_div(div));
- }
-
--const struct clk_ops krait_div2_clk_ops = {
-- .round_rate = krait_div2_round_rate,
-- .set_rate = krait_div2_set_rate,
-- .recalc_rate = krait_div2_recalc_rate,
-+const struct clk_ops krait_div_clk_ops = {
-+ .round_rate = krait_div_round_rate,
-+ .set_rate = krait_div_set_rate,
-+ .recalc_rate = krait_div_recalc_rate,
- };
--EXPORT_SYMBOL_GPL(krait_div2_clk_ops);
-+EXPORT_SYMBOL_GPL(krait_div_clk_ops);
---- a/drivers/clk/qcom/clk-krait.h
-+++ b/drivers/clk/qcom/clk-krait.h
-@@ -25,17 +25,20 @@ struct krait_mux_clk {
-
- extern const struct clk_ops krait_mux_clk_ops;
-
--struct krait_div2_clk {
-+struct krait_div_clk {
- u32 offset;
-- u8 width;
-+ u32 mask;
-+ u8 divisor;
- u32 shift;
- bool lpl;
-
- struct clk_hw hw;
- };
-
--#define to_krait_div2_clk(_hw) container_of(_hw, struct krait_div2_clk, hw)
-+#define to_krait_div_clk(_hw) container_of(_hw, struct krait_div_clk, hw)
-+#define krait_div_to_val(_div) ((_div) / 2) - 1
-+#define krait_val_to_div(_val) ((_val) + 1) * 2
-
--extern const struct clk_ops krait_div2_clk_ops;
-+extern const struct clk_ops krait_div_clk_ops;
-
- #endif
---- a/drivers/clk/qcom/krait-cc.c
-+++ b/drivers/clk/qcom/krait-cc.c
-@@ -86,11 +86,11 @@ static int krait_notifier_register(struc
- static struct clk_hw *
- krait_add_div(struct device *dev, int id, const char *s, unsigned int offset)
- {
-- struct krait_div2_clk *div;
-+ struct krait_div_clk *div;
- static struct clk_parent_data p_data[1];
- struct clk_init_data init = {
- .num_parents = ARRAY_SIZE(p_data),
-- .ops = &krait_div2_clk_ops,
-+ .ops = &krait_div_clk_ops,
- .flags = CLK_SET_RATE_PARENT,
- };
- struct clk_hw *clk;
-@@ -101,7 +101,8 @@ krait_add_div(struct device *dev, int id
- if (!div)
- return ERR_PTR(-ENOMEM);
-
-- div->width = 2;
-+ div->mask = 0x3;
-+ div->divisor = 2;
- div->shift = 6;
- div->lpl = id >= 0;
- div->offset = offset;
+++ /dev/null
-From ac84ac819a2e8fd3d87122b452c502a386c54437 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Tue, 5 Jul 2022 18:30:18 +0200
-Subject: [PATCH v2 4/4] clk: qcom: gcc-ipq806x: remove cc_register_board for
- pxo and cxo
-
-Now that these clock are defined as fixed clk in dts, we can drop the
-register_board_clk for cxo_board and pxo_board in gcc_ipq806x_probe.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- drivers/clk/qcom/gcc-ipq806x.c | 8 --------
- 1 file changed, 8 deletions(-)
-
---- a/drivers/clk/qcom/gcc-ipq806x.c
-+++ b/drivers/clk/qcom/gcc-ipq806x.c
-@@ -3386,14 +3386,6 @@ static int gcc_ipq806x_probe(struct plat
- struct regmap *regmap;
- int ret;
-
-- ret = qcom_cc_register_board_clk(dev, "cxo_board", "cxo", 25000000);
-- if (ret)
-- return ret;
--
-- ret = qcom_cc_register_board_clk(dev, "pxo_board", "pxo", 25000000);
-- if (ret)
-- return ret;
--
- if (of_machine_is_compatible("qcom,ipq8065")) {
- ubi32_core1_src_clk.freq_tbl = clk_tbl_nss_ipq8065;
- ubi32_core2_src_clk.freq_tbl = clk_tbl_nss_ipq8065;
+++ /dev/null
-From: Christian Lamparter <chunkeey@googlemail.com>
-Subject: SoC: add qualcomm syscon
---- a/drivers/soc/qcom/Makefile
-+++ b/drivers/soc/qcom/Makefile
-@@ -23,6 +23,7 @@ obj-$(CONFIG_QCOM_SOCINFO) += socinfo.o
- obj-$(CONFIG_QCOM_SPM) += spm.o
- obj-$(CONFIG_QCOM_STATS) += qcom_stats.o
- obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
-+obj-$(CONFIG_QCOM_TCSR) += qcom_tcsr.o
- obj-$(CONFIG_QCOM_APR) += apr.o
- obj-$(CONFIG_QCOM_LLCC) += llcc-qcom.o
- obj-$(CONFIG_QCOM_RPMHPD) += rpmhpd.o
---- a/drivers/soc/qcom/Kconfig
-+++ b/drivers/soc/qcom/Kconfig
-@@ -213,6 +213,13 @@ config QCOM_STATS
- various SoC level low power modes statistics and export to debugfs
- interface.
-
-+config QCOM_TCSR
-+ tristate "QCOM Top Control and Status Registers"
-+ depends on ARCH_QCOM
-+ help
-+ Say y here to enable TCSR support. The TCSR provides control
-+ functions for various peripherals.
-+
- config QCOM_WCNSS_CTRL
- tristate "Qualcomm WCNSS control driver"
- depends on ARCH_QCOM || COMPILE_TEST
---- /dev/null
-+++ b/drivers/soc/qcom/qcom_tcsr.c
-@@ -0,0 +1,64 @@
-+/*
-+ * Copyright (c) 2014, The Linux foundation. All rights reserved.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License rev 2 and
-+ * only rev 2 as published by the free Software foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ */
-+
-+#include <linux/clk.h>
-+#include <linux/err.h>
-+#include <linux/io.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_platform.h>
-+#include <linux/platform_device.h>
-+
-+#define TCSR_USB_PORT_SEL 0xb0
-+
-+static int tcsr_probe(struct platform_device *pdev)
-+{
-+ struct resource *res;
-+ const struct device_node *node = pdev->dev.of_node;
-+ void __iomem *base;
-+ u32 val;
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ base = devm_ioremap_resource(&pdev->dev, res);
-+ if (IS_ERR(base))
-+ return PTR_ERR(base);
-+
-+ if (!of_property_read_u32(node, "qcom,usb-ctrl-select", &val)) {
-+ dev_err(&pdev->dev, "setting usb port select = %d\n", val);
-+ writel(val, base + TCSR_USB_PORT_SEL);
-+ }
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id tcsr_dt_match[] = {
-+ { .compatible = "qcom,tcsr", },
-+ { },
-+};
-+
-+MODULE_DEVICE_TABLE(of, tcsr_dt_match);
-+
-+static struct platform_driver tcsr_driver = {
-+ .driver = {
-+ .name = "tcsr",
-+ .owner = THIS_MODULE,
-+ .of_match_table = tcsr_dt_match,
-+ },
-+ .probe = tcsr_probe,
-+};
-+
-+module_platform_driver(tcsr_driver);
-+
-+MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>");
-+MODULE_DESCRIPTION("QCOM TCSR driver");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/include/dt-bindings/soc/qcom,tcsr.h
-@@ -0,0 +1,23 @@
-+/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 and
-+ * only version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ */
-+#ifndef __DT_BINDINGS_QCOM_TCSR_H
-+#define __DT_BINDINGS_QCOM_TCSR_H
-+
-+#define TCSR_USB_SELECT_USB3_P0 0x1
-+#define TCSR_USB_SELECT_USB3_P1 0x2
-+#define TCSR_USB_SELECT_USB3_DUAL 0x3
-+
-+/* TCSR A/B REG */
-+#define IPQ806X_TCSR_REG_A_ADM_CRCI_MUX_SEL 0
-+#define IPQ806X_TCSR_REG_B_ADM_CRCI_MUX_SEL 1
-+
-+#endif
+++ /dev/null
---- a/arch/arm/Kconfig
-+++ b/arch/arm/Kconfig
-@@ -1589,6 +1589,14 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN
-
- endchoice
-
-+config CMDLINE_OVERRIDE
-+ bool "Use alternative cmdline from device tree"
-+ help
-+ Some bootloaders may have uneditable bootargs. While CMDLINE_FORCE can
-+ be used, this is not a good option for kernels that are shared across
-+ devices. This setting enables using "chosen/cmdline-override" as the
-+ cmdline if it exists in the device tree.
-+
- config CMDLINE
- string "Default kernel command string"
- default ""
---- a/drivers/of/fdt.c
-+++ b/drivers/of/fdt.c
-@@ -1187,6 +1187,17 @@ int __init early_init_dt_scan_chosen(cha
- if (p != NULL && l > 0)
- strlcat(cmdline, p, min_t(int, strlen(cmdline) + (int)l, COMMAND_LINE_SIZE));
-
-+ /* CONFIG_CMDLINE_OVERRIDE is used to fallback to a different
-+ * device tree option of chosen/bootargs-override. This is
-+ * helpful on boards where u-boot sets bootargs, and is unable
-+ * to be modified.
-+ */
-+#ifdef CONFIG_CMDLINE_OVERRIDE
-+ p = of_get_flat_dt_prop(node, "bootargs-override", &l);
-+ if (p != NULL && l > 0)
-+ strlcpy(cmdline, p, min((int)l, COMMAND_LINE_SIZE));
-+#endif
-+
- handle_cmdline:
- /*
- * CONFIG_CMDLINE is meant to be a default in case nothing else
+++ /dev/null
-From 2f86b9b71a11f86e3d850214ab781ebb17d7260e Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Fri, 19 Jan 2024 19:48:30 +0100
-Subject: [PATCH v2 1/2] ARM: decompressor: support memory start validation for
- appended DTB
-
-There is currently a problem with a very specific sets of kernel config
-and AUTO_ZRELADDR.
-
-For the most common case AUTO_ZRELADDR check the PC register and
-calculate the start of the physical memory. Then fdt_check_mem_start is
-called to make sure the detected value makes sense by comparing it with
-what is present in DTB in the memory nodes and if additional fixup are
-required with the use of linux,usable-memory-range in the chosen node to
-hardcode usable memory range in case some reserved space needs to be
-addressed. With the help of this function the right address is
-calculated and the kernel correctly decompress and loads.
-
-Things starts to become problematic when in the mix,
-CONFIG_ARM_APPENDED_DTB is used. This is a particular kernel config is
-used when legacy systems doesn't support passing a DTB directly and a
-DTB is appended at the end of the image.
-
-In such case, fdt_check_mem_start is skipped in AUTO_ZRELADDR iteration
-as the appended DTB can be augumented later with ATAGS passed from the
-bootloader (if CONFIG_ARM_ATAG_DTB_COMPAT is enabled).
-
-The main problem and what this patch address is the fact that
-fdt_check_mem_start is never called later when the appended DTB is
-augumented, hence any fixup and validation is not done making AUTO_ZRELADDR
-detection inconsistent and most of the time wrong.
-
-Add support in head.S for this by checking if AUTO_ZRELADDR is enabled
-and calling fdt_check_mem_start with the appended DTB and the augumented
-values permitting legacy device to provide info in DTB instead of
-disabling AUTO_ZRELADDR and hardcoding the physical address offsets.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
-Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
----
- arch/arm/boot/compressed/head.S | 22 ++++++++++++++++++++++
- 1 file changed, 22 insertions(+)
-
---- a/arch/arm/boot/compressed/head.S
-+++ b/arch/arm/boot/compressed/head.S
-@@ -443,6 +443,28 @@ restart: adr r0, LC1
- add r6, r6, r5
- add r10, r10, r5
- add sp, sp, r5
-+
-+#ifdef CONFIG_AUTO_ZRELADDR
-+ /*
-+ * Validate calculated start of physical memory with appended DTB.
-+ * In the first iteration for physical memory start calculation,
-+ * we skipped validating it as it could have been augumented by
-+ * ATAGS stored at an offset from the same start of physical memory.
-+ *
-+ * We now have parsed them and augumented the appended DTB if asked
-+ * so we can finally validate the start of physical memory.
-+ *
-+ * This is needed to apply additional fixup with
-+ * linux,usable-memory-range or to make sure AUTO_ZRELADDR detected
-+ * the correct value.
-+ */
-+ sub r0, r4, #TEXT_OFFSET @ revert to base address
-+ mov r1, r8 @ use appended DTB
-+ bl fdt_check_mem_start
-+
-+ /* Determine final kernel image address. */
-+ add r4, r0, #TEXT_OFFSET
-+#endif
- dtb_check_done:
- #endif
-
+++ /dev/null
-From 781d7cd4c3364e9d38fa12a342c5ad4c7e33a5ba Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Fri, 19 Jan 2024 20:33:10 +0100
-Subject: [PATCH v2 2/2] ARM: decompressor: add option to ignore MEM ATAGs
-
-Some bootloaders can pass broken MEM ATAGs that provide hardcoded
-information about mounted RAM size and physical location.
-Example booloader provide RAM of size 1.7Gb but actual mounted RAM
-size is 512Mb causing kernel panic.
-
-Add option CONFIG_ARM_ATAG_DTB_COMPAT_IGNORE_MEM to ignore these ATAG
-and not augument appended DTB memory node.
-
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Acked-by: Linus Walleij <linus.walleij@linaro.org>
----
- arch/arm/Kconfig | 12 ++++++++++++
- arch/arm/boot/compressed/atags_to_fdt.c | 4 ++++
- 2 files changed, 16 insertions(+)
-
---- a/arch/arm/Kconfig
-+++ b/arch/arm/Kconfig
-@@ -1570,6 +1570,18 @@ config ARM_ATAG_DTB_COMPAT
- bootloaders, this option allows zImage to extract the information
- from the ATAG list and store it at run time into the appended DTB.
-
-+config ARM_ATAG_DTB_COMPAT_IGNORE_MEM
-+ bool "Ignore MEM ATAG information from bootloader"
-+ depends on ARM_ATAG_DTB_COMPAT
-+ help
-+ Some bootloaders can pass broken MEM ATAGs that provide hardcoded
-+ information about mounted RAM size and physical location.
-+ Example booloader provide RAM of size 1.7Gb but actual mounted RAM
-+ size is 512Mb causing kernel panic.
-+
-+ Enable this option if MEM ATAGs should be ignored and the memory
-+ node in the appended DTB should NOT be augumented.
-+
- choice
- prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
- default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
---- a/arch/arm/boot/compressed/atags_to_fdt.c
-+++ b/arch/arm/boot/compressed/atags_to_fdt.c
-@@ -169,6 +169,10 @@ int atags_to_fdt(void *atag_list, void *
- setprop_string(fdt, "/chosen", "bootargs",
- atag->u.cmdline.cmdline);
- } else if (atag->hdr.tag == ATAG_MEM) {
-+ /* Bootloader MEM ATAG are broken and should be ignored */
-+ if (IS_ENABLED(CONFIG_ARM_ATAG_DTB_COMPAT_IGNORE_MEM))
-+ continue;
-+
- if (memcount >= sizeof(mem_reg_property)/4)
- continue;
- if (!atag->u.mem.size)
+++ /dev/null
-From 13bb6d8dd9138927950a520a288401db82871dc9 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Sun, 21 Jan 2024 23:36:57 +0100
-Subject: [PATCH] ARM: decompressor: support for ATAGs rootblock parsing
-
-The command-line arguments provided by the boot loader will be
-appended to a new device tree property: bootloader-args.
-
-If there is a property "append-rootblock" in DT under /chosen
-and a root= option in bootloaders command line it will be parsed
-and added to DT bootargs with the form: <append-rootblock>XX.
-
-This is usefull in dual boot systems, to get the current root partition
-without afecting the rest of the system.
-
-Signed-off-by: Adrian Panella <ianchi74@outlook.com>
-[ reworked to a cleaner patch ]
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
----
- arch/arm/Kconfig | 10 +++
- arch/arm/boot/compressed/atags_to_fdt.c | 102 ++++++++++++++++++++++--
- init/main.c | 12 +++
- 3 files changed, 117 insertions(+), 7 deletions(-)
-
---- a/arch/arm/Kconfig
-+++ b/arch/arm/Kconfig
-@@ -1599,6 +1599,16 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN
- The command-line arguments provided by the boot loader will be
- appended to the the device tree bootargs property.
-
-+config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE
-+ bool "Append rootblock parsing bootloader's kernel arguments"
-+ help
-+ The command-line arguments provided by the boot loader will be
-+ appended to a new device tree property: bootloader-args.
-+
-+ If there is a property "append-rootblock" in DT under /chosen
-+ and a root= option in bootloaders command line it will be parsed
-+ and added to DT bootargs with the form: <append-rootblock>XX.
-+
- endchoice
-
- config CMDLINE_OVERRIDE
---- a/arch/arm/boot/compressed/atags_to_fdt.c
-+++ b/arch/arm/boot/compressed/atags_to_fdt.c
-@@ -3,7 +3,8 @@
- #include <asm/setup.h>
- #include <libfdt.h>
-
--#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND)
-+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND) || \
-+ defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
- #define do_extend_cmdline 1
- #else
- #define do_extend_cmdline 0
-@@ -69,6 +70,83 @@ static uint32_t get_cell_size(const void
- return cell_size;
- }
-
-+/**
-+ * taken from arch/x86/boot/string.c
-+ * local_strstr - Find the first substring in a %NUL terminated string
-+ * @s1: The string to be searched
-+ * @s2: The string to search for
-+ */
-+static char *local_strstr(const char *s1, const char *s2)
-+{
-+ size_t l1, l2;
-+
-+ l2 = strlen(s2);
-+ if (!l2)
-+ return (char *)s1;
-+ l1 = strlen(s1);
-+ while (l1 >= l2) {
-+ l1--;
-+ if (!memcmp(s1, s2, l2))
-+ return (char *)s1;
-+ s1++;
-+ }
-+ return NULL;
-+}
-+
-+static char *append_rootblock(char *dest, const char *str, int len, void *fdt)
-+{
-+ char *ptr, *end, *tmp;
-+ const char *root="root=";
-+ const char *find_rootblock;
-+ int i, l;
-+ const char *rootblock;
-+
-+ find_rootblock = getprop(fdt, "/chosen", "find-rootblock", &l);
-+ if (!find_rootblock)
-+ find_rootblock = root;
-+
-+ /* ARM doesn't have __HAVE_ARCH_STRSTR, so it was copied from x86 */
-+ ptr = local_strstr(str, find_rootblock);
-+ if (!ptr)
-+ return dest;
-+
-+ end = strchr(ptr, ' ');
-+ end = end ? (end - 1) : (strchr(ptr, 0) - 1);
-+
-+ /* Some boards ubi.mtd=XX,ZZZZ, so let's check for '," too. */
-+ tmp = strchr(ptr, ',');
-+ if (tmp)
-+ end = end < tmp ? end : tmp - 1;
-+
-+ /*
-+ * find partition number
-+ * (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX | ubi.mtd=XX,ZZZZ )
-+ */
-+ for (i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++);
-+
-+ ptr = end + 1;
-+
-+ /* if append-rootblock property is set use it to append to command line */
-+ rootblock = getprop(fdt, "/chosen", "append-rootblock", &l);
-+ if (rootblock != NULL) {
-+ if (*dest != ' ') {
-+ *dest = ' ';
-+ dest++;
-+ len++;
-+ }
-+
-+ if (len + l + i <= COMMAND_LINE_SIZE) {
-+ memcpy(dest, rootblock, l);
-+ dest += l - 1;
-+
-+ memcpy(dest, ptr, i);
-+ dest += i;
-+ }
-+ }
-+
-+ return dest;
-+}
-+
- static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline)
- {
- char cmdline[COMMAND_LINE_SIZE];
-@@ -86,13 +164,23 @@ static void merge_fdt_bootargs(void *fdt
- ptr += len - 1;
- }
-
-- /* and append the ATAG_CMDLINE */
- if (fdt_cmdline) {
-- len = strlen(fdt_cmdline);
-- if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) {
-- *ptr++ = ' ';
-- memcpy(ptr, fdt_cmdline, len);
-- ptr += len;
-+ if (IS_ENABLED(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)) {
-+ /*
-+ * save original bootloader args
-+ * and append ubi.mtd with root partition number
-+ * to current cmdline
-+ */
-+ setprop_string(fdt, "/chosen", "bootloader-args", fdt_cmdline);
-+ ptr = append_rootblock(ptr, fdt_cmdline, len, fdt);
-+ } else {
-+ /* and append the ATAG_CMDLINE */
-+ len = strlen(fdt_cmdline);
-+ if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) {
-+ *ptr++ = ' ';
-+ memcpy(ptr, fdt_cmdline, len);
-+ ptr += len;
-+ }
- }
- }
- *ptr = '\0';
---- a/init/main.c
-+++ b/init/main.c
-@@ -28,6 +28,7 @@
- #include <linux/initrd.h>
- #include <linux/memblock.h>
- #include <linux/acpi.h>
-+#include <linux/of.h>
- #include <linux/bootconfig.h>
- #include <linux/console.h>
- #include <linux/nmi.h>
-@@ -996,6 +997,17 @@ asmlinkage __visible void __init __no_sa
- pr_notice("Kernel command line: %s\n", saved_command_line);
- /* parameters may set static keys */
- jump_label_init();
-+
-+ /* Show bootloader's original command line for reference */
-+ if (IS_ENABLED(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE) && of_chosen) {
-+ const char *prop = of_get_property(of_chosen, "bootloader-args", NULL);
-+
-+ if(prop)
-+ pr_notice("Bootloader command line (ignored): %s\n", prop);
-+ else
-+ pr_notice("Bootloader command line not present\n");
-+ }
-+
- parse_early_param();
- after_dashes = parse_args("Booting kernel",
- static_command_line, __start___param,
projects / openwrt / openwrt.git / commitdiff