Sander Vanheule [Wed, 21 Sep 2022 19:53:24 +0000 (21:53 +0200)]
TEST realtek: GS1900: use wrong RTL8231 MDIO address
Sander Vanheule [Wed, 21 Sep 2022 19:51:12 +0000 (21:51 +0200)]
TEST realtek: rtl8231: extra pr_info()s
Sander Vanheule [Tue, 20 Sep 2022 20:21:05 +0000 (22:21 +0200)]
TEST realtek: reset rtl8231 on probe
Rafał Miłecki [Wed, 21 Sep 2022 05:53:52 +0000 (07:53 +0200)]
bcm4908: fix -EPROBE_DEFER support in bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 20 Sep 2022 21:07:33 +0000 (23:07 +0200)]
kernel: update U-Boot NVMEM driver
1. Fix casting
2. Support DT-defined variables
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 20 Sep 2022 20:34:27 +0000 (22:34 +0200)]
bcm4908: backport mtd parser for Broadcom's U-Boot partition
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Stijn Tintel [Tue, 20 Sep 2022 16:27:34 +0000 (19:27 +0300)]
mediatek: fix Unifi 6LR network config
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb85 ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a78f ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a1192 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Mon, 22 Aug 2022 13:05:01 +0000 (15:05 +0200)]
ci: show build failures directly in job log output
Instead of waiting for complete workflow finish, then downloading the
artifacts, unpacking them and inspecting them, lets try to make the
build failure immediately visible in the log output:
====== Make errors from logs/target/linux/compile.txt ======
* Legacy (non-UHI/non-FIT) Boards
*
Support MIPS SEAD-3 boards (LEGACY_BOARD_SEAD3) [N/y/?] (NEW)
Error in reading or end of file.
make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1
make[5]: *** [Makefile:616: syncconfig] Error 2
make[4]: *** [Makefile:736: include/config/auto.conf.cmd] Error 2
make[3]: *** [Makefile:24: build_dir/target-mipsel-openwrt-linux-musl_musl/linux-ramips_mt7620/linux-5.15.62/.modules] Error 2
make[2]: *** [Makefile:11: compile] Error 2
time: target/linux/compile#30.09#11.30#37.92
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 5 Sep 2022 07:04:27 +0000 (09:04 +0200)]
ci: move scripts into separate directory
So it's clean and tidy.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Tue, 20 Sep 2022 09:32:51 +0000 (11:32 +0200)]
kernel: backport MTK ethernet/WLAN offload fixes
Fixes issues with offloading to WED, especially with VLAN bridges involved
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Tue, 20 Sep 2022 03:31:24 +0000 (04:31 +0100)]
xdp-tools: update to version 1.2.8
82628d8 libxdp: Fix resource leaks
7fb0af0 libxdp: always clone program fd before taking ownership of it
d8cd007 headers: Update kernel btf.h header file
2265125 (tag: v1.2.7) xdp-filter: Update examples in documentation
2b65008 libxdp: Fix libxdp compilation error
2387514 xsk: remove unused variable outstanding_tx
00b5a95 Fix section names in xsk programs
d4ff1f9 (tag: v1.2.8) Bump TOOLS_VERSION to 1.2.8
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Fri, 19 Aug 2022 00:17:22 +0000 (02:17 +0200)]
hostapd: update to 2022-07-29
b704dc72e tests: sigma_dut and updated ConfResult value for Configurator failures
89de431f2 DPP: Add config response status value to DPP-CONF-SENT
10104915a tests: sigma_dut and DPP PB session overlap
80d5e264c Enhance QCA vendor roam event to indicate MLO links after reassociation
662249306 Update copyright notices for the QCA vendor definitions
8adcdd659 tests: Temporary workaround for dpp_chirp_ap_5g
ddcd15c2d tests: Fix fuzzing/sae build
7fa67861a tests: Fix p2p_channel_avoid3
ee3567d65 tests: Add more time for scan/connection
1d08b238c nl80211: Allow more time for the initial scan with 6 GHz
ac9e6a2ab tests: Allow 6 GHz opclasses in MBO checks
faf9c04cb Remove a host of unnecessary OPENSSL_IS_BORINGSSL ifdefs
b9cd5a82f Always process pending QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH data
ef4cd8e33 QoS: Use common classifier_mask for ipv4/ipv6
93be02592 Add fixed FDD mode to qca_btc_chain_mode QCA vendor attribute
e7cbfa1c1 tests: sigma_dut and DPP Enrollee unsupported curves
5565fbee2 DPP: Check Enrollee supported curves when building Config Response
ceae05cec tests: sigma_dut and DPP MUDURL setting for hostapd
4cfb484e9 DPP: Allow dpp_controller_start without arguments in CLIs
c97000933 Fix ifdef condition for imsi_privacy_cert
2a9a61d6c tests: SAE with extended key AKM
e35f6ed1d tests: More detailed report on SAE PMKSA caching error case
f70db167a SAE: Derive a variable length PMK with the new AKM suites
91010e6f6 SAE: Indicate AKM suite selector in commit for new AKM suites
e81ec0962 SAE: Use H2E unconditionally with the new AKM suites
f8eed2e8b SAE: Store PMK length and AKM in SAE data
9dc4e9d13 SAE: EAPOL-Key and key/MIC length information for the new AKM suites
a32ef3cfb SAE: Driver capability flags for the new SAE AKM suites
91df8c9c6 SAE: Internal WPA_KEY_MGMT_* defines for extended key AKMs
5c8a714b1 SAE: Use wpa_key_mgmt_sae() helper
5456b0f26 Define new RSN AKM suite selector values
def33101c DPP: Clear push button announcement state on wpa_supplicant FLUSH
35587fa8f tests: DPP Controller/Relay with need to discover Controller
d22dfe918 DPP: Event message for indicating when Relay would need a Controller
ca7892e98 tests: DPP Relay and adding/removing connection to a Controller
bfe3cfc38 DPP: Allow Relay connections to Controllers to be added and removed
808834b18 Add a comparison function for hostapd_ip_addr
f7763880b DPP: Advertise Configurator connectivity on Relay automatically
ff7cc1d49 tests: DPP Relay and dynamic Controller addition
ca682f80a DPP: Dynamic Controller initiated connection on Relay
d2388bcca DPP: Strict validation of PKEX peer bootstrapping key during auth
a7b8cef8b DPP3: Fix push button boostrapping key passing through PKEX
69d7c8e6b DPP: Add peer=id entry for PKEX-over-TCP case
b607d2723 tests: sigma_dut and DPP PB Configurator in wpa_supplicant
1ff9251a8 DPP3: Push button Configurator in wpa_supplicant
b94e46bc7 tests: PB Configurator in wpa_supplicant
ca4e82cbf tests: sigma_dut DPP/PKEX initiator as Configurator over TCP and Wi-Fi
e9137950f DPP: Recognize own PKEX Exchange Request if it ends up being received
692956446 DPP: Note PKEX code/identifier deletion in debug log
dfa9183b1 tests: DPP reconfig after Controller-initiated operation through Relay
ae4a3a6f6 DPP: Add DPP-CONF-REQ-RX event for Controller
17216b524 tests: sigma_dut DPP/PKEX initiator as Configurator (TCP) through Relay
fb2937b85 DPP: Allow Controller to initiate PKEX through Relay
15af83cf1 DPP: Delete PKEX code and identifier on success completion of PKEX
d86ed5b72 tests: Allow DPP_PKEX_REMOVE success in dpp_pkex_hostapd_errors
0a4f391b1 tests: sigma_dut and DPP Connector Privacy
479e412a6 DPP3: Default value for dpp_connector_privacy
7d12871ba test: DPP Private Peer Introduction protocol
148de3e0d DPP3: Private Peer Introduction protocol
786ea402b HPKE base mode with single-shot API
f0273bc81 OpenSSL: Remove a forgotten debug print
f2bb0839f test: DPP 3rd party config information
68209ddbe DPP: Allow 3rd party information to be added into config object
0e2217c95 DPP: Allow 3rd party information to be added into config request obj
3d82fbe05 Add QCA vendor subcommand and attributes for SCS rule configuration
16b62ddfa QCA vendor attribute for DBAM configuration
004b1ff47 tests: DPP Controller initiating through Relay
451ede2c3 DPP: Allow AP/Relay to be configured to listed for new TCP connections
248654d36 tests: sigma_dut DPP PB test cases
697b7d7ec tests: DPP push button
7bbe85987 DPP3: Allow external configuration to be specified on AP for PB
8db786a43 DPP3: Testing functionality for push button announcements
37bccfcab DPP3: Push button bootstrap mechanism
a0054fe7c Add AP and STA specific P802.11az security capabilities (vendor command)
159e63613 QCA vendor command for CoAP offload processing
3b7bb17f6 Add QCA vendor attribute for TIM beacon statistics
09a281e52 Add QCA vendor interface for PASN offload to userspace
809fb96fa Add a vendor attribute to configure concurrency policy for AP interface
a5754f531 Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY
085a3fc76 EHT: Add 320 channel width support
bafe35df0 Move CHANWIDTH_* definitions from ieee80211_defs.h to defs.h
92f549901 tests: Remove the 80+80 vs. 160 part from wpa2_ocv_ap_vht160_mismatch
c580c2aec tests: Make OCV negative test error cases more robust
3c2ba98ad Add QCA vendor event to indicate driver recovery after internal failures
6b461f68c Set current_ssid before changing state to ASSOCIATING
8dd826741 QCA vendor attribute to configure direct data path for audio traffic
504be2f9d QCA vendor command support to get WLAN radio combinations
d5905dbc8 OCV: Check the Frequency Segment 1 Channel Number only on 80+80 MHz
Signed-off-by: David Bauer <mail@david-bauer.net>
Michael Pratt [Thu, 30 Jun 2022 03:48:47 +0000 (23:48 -0400)]
tools/cmake: fix download url with make variables
Use a make variable pattern for the url
so that only one version number needs to be changed
when version is bumped.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Florian Eckert [Wed, 11 Aug 2021 09:58:45 +0000 (11:58 +0200)]
target/x86: add grub2-bios-setup to DEFAULT_PACKAGES
With the commit
5876d6a62fc0ae5799e7d9c896356f75c99a6f0a the command under
`/usr/sbin/grub-bios-setup` has been moved to its own package named
`grub-bios-setup`.
The script `81_upgrade_bootloader` under `/lib/preinit` is used by all
x86 targets to update the bootloader. The script is using the command
`grub-bios-setup` for this.
I get the following output at the first boot after the upgrade.
`/etc/preinit: line 9: /usr/sbin/grub-bios-setup: not found`.
To fix this, the DEFAULT_PACKAGES dependency is extended by the entry
`grub2-bios-setup` so that the missing command is installed again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Andrew Sim [Sat, 17 Sep 2022 06:36:34 +0000 (08:36 +0200)]
ipq40xx: fix power LED colour ID in Netgear WAC510 dts
led_power_green color ID in dts is mistakenly set to amber so
correct it by setting it to green
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Christian Marangi [Tue, 13 Sep 2022 17:04:12 +0000 (19:04 +0200)]
generic: 5.15: backport stmmac patches to change MTU
Backport stmmac patches to change MTU while the interface is up.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Mon, 12 Sep 2022 16:40:16 +0000 (18:40 +0200)]
generic: 5.15: qca8k: backport code split patch
Backport upstream code split patch for qca8k needed for ipq40xx target
to correctly implement a DSA driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Tue, 13 Sep 2022 17:01:50 +0000 (19:01 +0200)]
generic: 5.15: qca8k: add kernel version tag on backport patch
Add kernel tag that introduced the patch on backport patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Alex Low [Mon, 19 Sep 2022 10:20:37 +0000 (12:20 +0200)]
build: harden GitHub workflow permissions
Grant pull-requests write permission to the labeler workflow and
read-only to everything else.
Signed-off-by: Alex Low <aleksandrosansan@gmail.com>
[ wrap to 80 columns and fix wrong author as requested by author itself ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Sat, 17 Sep 2022 19:11:12 +0000 (20:11 +0100)]
mac80211: rt2x00: replace patches with v3 of pending series
See also patchwork for submission progress:
https://patchwork.kernel.org/project/linux-wireless/cover/cover.
1663445157.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Markus Stockhausen [Sun, 18 Sep 2022 18:30:39 +0000 (20:30 +0200)]
realtek: use upstream recommendation for secondary CPU start
Currently we fix interrupts/timers for the secondary CPU by patching
vsmp_init_secondary(). Get a little bit more generic and use the
upstream recommended way instead. Additionally avoid a check around
register_cps_smp_ops() because it does that itself.
See https://lkml.org/lkml/2022/9/12/522
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Markus Stockhausen [Wed, 7 Sep 2022 15:02:35 +0000 (17:02 +0200)]
realtek: avoid wrong interrupt routing
The interrupt controller depends on two control registers. GIMR enables
or disables interrupts and IRRx routes these to MIPS CPU interrupts 2-7.
Wiki currently states "A value of '0' (in IRRx) disconnects this input from
the output line, independent of the line's setting in GIMR."
Contrary to normal intuition this statement DOES NOT mean, that interrupts
can be disabled by IRRx alone. The sad truth was discovered by enabling
SMP for an Zyxel XGS1010 on the 930x target. It shows that driver and
interrupts behave as follows:
- Timer 0 interrupt 7 has active routing to CPU0 and no routing to CPU1
- Timer 1 interrupt 8 has no routing to CPU0 and active routing to CPU1
- Unmasking (enabling) interrupts writes 1 bits to all GIMR registers
- Masking (disabling) interrupts writes 0 bits to both GIMR registers
During operation we can encounter a situation like
- GIMR bit for a interrupt/CPU combination is set to enabed (=1)
- IRRx routing bits for a interrupt/CPU combination are set to disabed (=0)
This setting already allows the hardware to fire interrupts to the target
CPU/VPE if the other CPU/VPE is currently busy. Especially for CPU bound
timer interrupts this is lethal. If timer interrupt 7 arrives at CPU1 and
vice versa for interrupt 8 the restart trigger gets lost. The timer dies
and a msleep() operation in the kernel will halt endlessly.
Fix this by tracking the IRRx active routing setting in a new bitfield with
0="routing active" and 1="no routing". Enable interrupts in GIMR only
for a interrupt & CPU if routing is active. Thus we have
- GIMR = 0 / IRRx = 0 -> everything disabled
- GIMR = 1 / IRRx > 0 -> active and normal routing
- GIMR = 0 / IRRx > 0 -> masked (disabled) with normal routing
- GIMR = 1 / IRRx = 0 -> no longer possible
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Sungbo Eo [Sun, 18 Sep 2022 01:13:56 +0000 (10:13 +0900)]
ipq40xx: disable devices with 3MiB kernel size
The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently
fail on buildbots due to the KERNEL_SIZE, as stated in commit
17b7756b5a20 ("ipq40xx: 5.15: add testing kernel version"). Disable
these boards for now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Arınç ÜNAL [Wed, 14 Sep 2022 18:31:00 +0000 (21:31 +0300)]
ramips: mt7621-dts: change phy-mode of gmac1 to rgmii
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Arınç ÜNAL [Wed, 14 Sep 2022 18:30:59 +0000 (21:30 +0300)]
ramips: fix GB-PC1 and GB-PC2 LEDs
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.
Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Sander Vanheule [Sun, 18 Sep 2022 08:12:16 +0000 (10:12 +0200)]
realtek: use Device prefix for common recipes
The Build prefix is used for image build commands, while the Device
prefix should be used for base recipes for devices. Apply the same
naming convention here.
While touching the file, also fix the mixed indentation.
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Felix Fietkau [Sun, 18 Sep 2022 04:27:09 +0000 (06:27 +0200)]
build: fix including modules.mk for targets pulled in from feeds
Fixes: ebc36ebb2349 ("scripts/feeds: install targets to target/linux/feeds and support overriding")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Fri, 9 Sep 2022 23:06:02 +0000 (01:06 +0200)]
hostapd: don't select indoor channel on outdoor operation
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Nick Hainke [Sat, 17 Sep 2022 06:05:47 +0000 (08:05 +0200)]
wireless-regdb: update to 2022-08-12
Changes:
9dc9c89 wireless-regdb: update regulatory database based on preceding changes
442bc25 wireless-regdb: update 5 GHz rules for PK and add 60 GHz rule
daee7f3 wireless-regdb: add 5 GHz rules for GY
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 17 Sep 2022 06:30:00 +0000 (08:30 +0200)]
linux-firmware: update to
20220913
Changes:
f09bebf amdgpu: update yellow carp DMCUB firmware
db6db36 amdgpu: add firmware for VCN 3.1.2 IP block
3647da5 amdgpu: add firmware for SDMA 5.2.6 IP block
639b5c1 amdgpu: add firmware for PSP 13.0.5 IP block
7658946 amdgpu: add firmware for GC 10.3.6 IP block
427ca6c amdgpu: add firmware for DCN 3.1.5 IP block
edf9a2b qcom: rename Lenovo ThinkPad X13s firmware paths
9ebd5a5 rtw89: 8852c: update fw to v0.27.42.0
7546432 rtw89: 8852c: update fw to v0.27.36.0
2f2f018 Mellanox: Add new mlxsw_spectrum firmware xx.2010.3146
706a462 amdgpu: update beige goby VCN firmware
09ec438 amdgpu: update dimgrey cavefish VCN firmware
647021b amdgpu: update navy flounder VCN firmware
3c1662d amdgpu: update sienna cichlid VCN firmware
d3c9228 rtl_bt: Update RTL8852C BT USB firmware to 0xDFB8_5A33
a1c4b15 mediatek: reference the LICENCE file for MediaTek firmwares
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 17 Sep 2022 06:23:39 +0000 (08:23 +0200)]
linux-firmware: update to
20220815
Changes:
12ca075 mediatek: Add new mt8186 SOF firmware
aed71f2 ice: Update package to 1.3.30.0
1ee415b QCA: Update Bluetooth WCN685x 2.1 firmware to 2.1.0-00438
c58f001 brcm: Add nvram for Lenovo Yoga Tablet 2 830F/L and 1050F/L tablets
d4a4224 brcm: Add nvram for the Xiaomi Mi Pad 2 tablet
7220731 brcm: Add nvram for the Asus TF103C tablet
89ec619 Add amd-ucode README file
4f8f67e qca: Update firmware files for BT chip WCN6750.
This commit will update required firmware files for WCN6750.
e6857b6 amdgpu: Update Yellow Carp VCN firmware
e6185d5 linux-firmware: Update firmware file for Intel Bluetooth 9462
140beaf linux-firmware: Update firmware file for Intel Bluetooth 9462
045847e linux-firmware: Update firmware file for Intel Bluetooth 9560
f7f3d1f linux-firmware: Update firmware file for Intel Bluetooth 9560
45c5e53 linux-firmware: Update firmware file for Intel Bluetooth AX201
1068c45 linux-firmware: Update firmware file for Intel Bluetooth AX201
b93bf2c linux-firmware: Update firmware file for Intel Bluetooth AX211
31d24ca linux-firmware: Update firmware file for Intel Bluetooth AX211
447ca4a linux-firmware: Update firmware file for Intel Bluetooth AX210
87d07fd linux-firmware: Update firmware file for Intel Bluetooth AX200
63a87d2 linux-firmware: Update firmware file for Intel Bluetooth AX201
a45053c Mellanox: Add new mlxsw_spectrum firmware xx.2010.3020
4ae4ae8 qcom: Add firmware for Lenovo ThinkPad X13s
feda199 linux-firmware: Add firmware for Cirrus CS35L41
a4235e0 i915: Add GuC v70.4.1 for DG2
3ab394a i915: Add DMC v2.07 for DG2
150864a amdgpu partially revert "amdgpu: update beige goby to release 22.20"
56cf646 mediatek: Update mt8183/mt8192/mt8195 SCP firmware
4421586 amdgpu: update renoir to release 22.20
06cead1 amdgpu: update beige goby to release 22.20
d3e37b7 amdgpu: update yellow carp to release 22.20
9149732 amdgpu: update dimgrey cavefish to release 22.20
c2f5699 amdgpu: update vega20 to release 22.20
c3afe6a amdgpu: update vega12 to release 22.20
e840fe5 amdgpu: update raven to release 22.20
efe98d4 amdgpu: update navy flounder to release 22.20
5f13921 amdgpu: update vega10 to release 22.20
8da4640 amdgpu: update sienna cichlid to release 22.20
3fbfd89 amdgpu: update navi14 to release 22.20
8fe4b42 amdgpu: update green sardine to release 22.20
ca36bb9 amdgpu: update vangogh to release 22.20
21ba56c amdgpu: update navi12 to release 22.20
e9918d2 amdgpu: update navi10 to release 22.20
f379030 amdgpu: update picasso to release 22.20
1826c07 amdgpu: update aldebaran to release 22.20
1cbf1c6 amdgpu: update psp 13.0.8 TA firmware
35bb3bd WHENCE: Fix the dangling symlinks fix
84661a3 amdgpu: update DMCUB firmware for DCN 3.1.6
dfa2931 WHENCE: Correct dangling symlinks
Signed-off-by: Nick Hainke <vincent@systemli.org>
Olliver Schinagl [Tue, 13 Sep 2022 14:52:50 +0000 (16:52 +0200)]
realtek: move Netgear recipe to subtarget Makefile
There seems to be no reason to have the Netgear switches as part of
the main Makefile. Move it to its subtarget-specific Makefile since
it is only applicable there.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[update commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Sat, 17 Sep 2022 20:20:30 +0000 (22:20 +0200)]
realtek: move hpe_1920 recipe to common.mk
Currently supported HPE 1920 devices all have an RTL838x SoC, but there
are larger switches with RTL839x SoCs, although currently not supported.
Move the build recipe to common.mk so the larger devices can also make
use of the recipe, while moving it out of the main Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Sat, 17 Sep 2022 20:06:37 +0000 (22:06 +0200)]
realtek: merge duplicated DGS-1210 recipes
The D-Link DGS-1210 device series currently has supported devices with
both RTL838x and RTL839x SoCs. An image build recipe has been defined in
both subtarget makefiles, but these are mostly identical, save for the
SOC variable.
Move the SOC variable from the DGS-1210 build recipes to the applicable
devices, and put the remaining duplicate code in a shared Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Markus Stockhausen [Sat, 17 Sep 2022 17:12:19 +0000 (19:12 +0200)]
realtek: add support for DGS-1210-52
Hardware specification
----------------------
* RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz
* 128MB DRAM
* 32MB NOR Flash
* 48 x 10/100/1000BASE-T ports
- 6 x External PHY with 8 ports (RTL8218D)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14
The gpio-restart node is not required but it does reset the switch.
TODO: The 4 combo ports attached to the RTL8214FC are not detect
properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES"
and 51 and 52 as "RTL8218B (external)". Those ports only work if
u-boot initialize it (for example, loading initramfs image using one
of those ports). A patch to PHY detection is needed for full support.
The firmware recovery using U-Boot is broken for all DGS-1210 tested
devices as pressing RESET does not trigger it (only if pressed from a
running stock image)
UART pinout
-----------
[o]ooo|J14
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM upgrade
------------------------------
1. Make sure you are running OEM firmware in image2 slot (logged as admin):
- > config firmware image_id 2 boot_up
- > reboot
2. Install squashfs-factory_image1.bin to image1 using (logged as admin):
- > download firmware_fromTFTP <tftpserver> factory_image1.bin
- > config firmware image_id 1 boot_up
- > reboot
Installation using serial interface
-----------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
Once booted the initramfs, install the squashfs-sysupgrade.bin as a
normal OpenWrt system.
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / boot image 1 (CLI as admin):
- > config firmware image_id 1 boot_up
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000'
- # fw_setenv image '/dev/mtdblock7'
- # reboot
Debrick using serial interface
------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
Back to stock firmware using dual-boot
--------------------------------------
If you have serial interface, you can change u-boot env vars
interrupting the boot process. If not but you are running OpenWrt, you
can dual-boot (as mentioned eariler) and skip to step 4:
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Boot the image 2:
- set image /dev/mtdblock7; run addargs; bootm 0xb4e80000
4. Once booted, log as admin and change the boot image to 2
- > config firmware image_id 2 boot_up
- > reboot
5. After the boot, flash image1 with the vendor image
Back to stock firmware using DNA
--------------------------------
1. From an OpenWrt:
- # fw_setenv bootstop on
- # reboot
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
It has been developed and tested on device with F3 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Markus Stockhausen [Sat, 17 Sep 2022 17:06:33 +0000 (19:06 +0200)]
realtek: align DT macros in RTL839X with RTL838X
Add a missing definition to the RTL839X DT.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Markus Stockhausen [Sat, 17 Sep 2022 17:03:13 +0000 (19:03 +0200)]
realtek: D-Link make common DT include generic
The D-Link DGS device tree was reorganized to better reflect the common
DT parts. The common include is named SOC specific (838X) and it seemed
like a good choice to add another common include in the future for the
RTL839X devices. From the current point of view this option is not really
needed.
1. The common part only includes data that matches RTL839X devices too.
2. The Panasonic DT structure avoids including the basic DTSI inside the
common DTSI.
Taking simplicity of the Panasonic include logic and in perparation to
provide DGS-1210-52 support it makes sense to harmonize this.
- rename common include to reflect its content
- move the link to the root DTSI directly to the device specific DTS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Sungbo Eo [Sat, 17 Sep 2022 18:06:18 +0000 (03:06 +0900)]
ramips: 5.15: add disabled PINCTRL_AW9523
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.
Fixes: 675cf7557829 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a58 ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c330e ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c2563 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da866982 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sat, 17 Sep 2022 18:06:00 +0000 (03:06 +0900)]
ramips: 5.15: refresh subtarget kconfigs
Refresh config with `make kernel_oldconfig`.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sat, 17 Sep 2022 16:07:32 +0000 (01:07 +0900)]
ath79: specify factory.bin recipe for ASUS RP-AC51
Currently factory.bin image recipe of ASUS RP-AC51 is not specified
explicitly and is thus set to the leaked one from the device recipe
right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage.
Fixes: 416d4483e878 ("ath79: add support for ASUS RP-AC51")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Mon, 31 Jan 2022 17:53:59 +0000 (02:53 +0900)]
mac80211: rt2x00: fix typo
Add missing semicolon and refresh patches.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Andre Heider [Fri, 2 Sep 2022 07:48:22 +0000 (09:48 +0200)]
ltq-[a|v]dsl-app: provide ltq-dsl-app
This makes it easier for packages to depend on any
lantiq/intel/maxlinear compatible dsl daemon.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Tue, 23 Aug 2022 13:18:49 +0000 (15:18 +0200)]
ltq-vdsl-app: rename to ltq-vdsl-vr9-app
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 15 Jul 2022 12:32:59 +0000 (14:32 +0200)]
lantiq: rename ltq-vdsl folder to ltq-vdsl-vr9
Now PKG_NAME matches the folder name, and this will avoid confusion with
any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 15 Jul 2022 12:30:29 +0000 (14:30 +0200)]
lantiq: rename ltq-vdsl-mei folder to ltq-vdsl-vr9-mei
Now PKG_NAME matches the folder name, and this will avoid confusion with
any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
John Audia [Thu, 15 Sep 2022 13:56:36 +0000 (09:56 -0400)]
kernel: bump 5.10 to 5.10.143
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Thu, 15 Sep 2022 12:07:08 +0000 (08:07 -0400)]
kernel: bump 5.15 to 5.15.68
All patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
Daniel Golle [Fri, 16 Sep 2022 23:33:30 +0000 (00:33 +0100)]
mac80211: clean and submit a bunch of rt2x00 patches
Clean and submit patches, mostly related to MT7620 to linux-wireless
mailing list:
https://patchwork.kernel.org/project/linux-wireless/list/?series=677770
Replace local patches with now submitted versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 14 Sep 2022 19:16:50 +0000 (20:16 +0100)]
packages: libusb: add package 'fxload' (from libusb examples)
The 'fxload' tool contained in the examples provided with libusb is
actually useful and turns out to be the only way to load firmware into
some rather ancient EZ-USB microcontrollers made by Cypress (formerly
Anchor Chips).
The original 'fxload' tool from hotplug-linux has been abandonned long
ago and requires usbfs to be mounted in /proc/bus/usb/ (like it was in
Linux 2.4...).
Hence the best option is to package the modern 'fxload' from the libusb
examples which (unsurprisingly) uses libusb and works on modern
systems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 16 Sep 2022 20:02:28 +0000 (22:02 +0200)]
unetd: add missing init script
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 16 Sep 2022 19:57:57 +0000 (21:57 +0200)]
unetd: update to the latest version
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 16 Sep 2022 19:11:05 +0000 (21:11 +0200)]
unetd: update to the latest version
21360a1b1ce6 cli: fix typo
abfebece0af1 wg-linux: ship a copy of linux/wireguard.h
1cbb1a543cb3 pex: reduce unnecessary ping traffic
0c2f39e52d5d pex: remove pex event debug spam
dcf1362c2104 pex: add support for sending/receiving global PEX messages via unix socket
df5f70b8858c ubus: notify on network updates
e58a56697131 add DHT discovery service
be175767bc67 pex: keep active pex hosts after the specified timeout
543e4a3d2ed7 pex: move rx header check to callback function
395659b9c415 pex: move raw ip send code to sendto_rawudp() in utils.c
dda15ea8b3b2 pex: add utility function to get the sockets based on type / address family
e88f2cd4d3f0 utils: add support for passings address family to network_get_endpoint()
639cdcdf6eda pex: add support for figuring out the external data port via STUN servers
9144339ebe1f pex: improve handling of a longer list of PEX hosts
38212218ecdd unet-cli: add DHT support
0d37ca75434d pex: automatically create host entries from incoming endpoint port notifications
035fcc56ef60 host: keep multiple endpoint candidates, one for each type
a089e8ae7504 pex: avoid sending a query to a host more than once every 15 seconds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 16 Sep 2022 15:06:05 +0000 (17:06 +0200)]
unetd: select unetd from unet-cli instead of depending on it
Some people may explicitly want to select unet-cli for admin purposes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Eneas U de Queiroz [Mon, 8 Aug 2022 00:56:50 +0000 (21:56 -0300)]
wolfssl: add libwolfssl-cpu-crypto package
libwolfssl-cpu-crypto is a variant of libwolfssl with support for
cryptographic CPU instructions on x86_64 and aarch64.
On aarch64, wolfSSL does not perform run-time detection, so the library
will crash when the AES functions are called. A preinst script attempts
to check for support by querying /proc/cpuinfo, if installed in a
running system. When building an image, the script will check the
DISTRIB_TARGET value in /etc/openwrt_release, and will abort
installation if target is bcm27xx.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Jo-Philipp Wich [Mon, 12 Sep 2022 11:48:40 +0000 (13:48 +0200)]
rpcd: update to latest Git HEAD
e80d0b2 ucode: pass-through `ubus_rpc_session` argument
0d02243 ucode: initialize module search path early
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Mon, 5 Sep 2022 08:50:39 +0000 (10:50 +0200)]
ucode: update to latest Git HEAD
cc4eb79 ubus: support obtaining numeric error code
01c412c ubus: add toplevel constants for ubus status codes
8e240fa ubus: allow object method call handlers to return a numeric status code
5cdddd3 lib: add limit support to split() and replace()
0ba9c3e fs: add optional third permission argument to fs.open()
c1f7b3b lib: remove fixed capture group limit in match() and regex replace()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Koen Vandeputte [Tue, 13 Sep 2022 11:44:17 +0000 (13:44 +0200)]
kernel: mhi: backport upstream patch
This patch will print the name of the modem in the bootlog
during probing.
This allows to verify that the exact model was loaded and not some
generic type.
The only other way to do this is by enabling dynamic debugging
which is disabled by default in OpenWRT
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Koen Vandeputte [Mon, 22 Aug 2022 09:18:35 +0000 (11:18 +0200)]
mac80211: merge upstream fixes
fetched from upstream kernel v5.15.67
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Felix Fietkau [Thu, 15 Sep 2022 14:38:18 +0000 (16:38 +0200)]
mac80211: merge pending fixes for tx queueing issues
Fixes a potential deadlock and a tx queue hang on STA assoc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 15 Sep 2022 11:35:52 +0000 (13:35 +0200)]
mt76: update to the latest version
94eb0bc1374d wifi: mt76: testmode: use random payload for tx packets
f8ece810002b wifi: mt76: add rx_check callback for usb devices
67fbdb7bed90 wifi: mt76: mt7921e: fix race issue between reset and suspend/resume
a9b09dd2715f wifi: mt76: mt7921s: fix race issue between reset and suspend/resume
ee3eb0d6d52e wifi: mt76: mt7921u: fix race issue between reset and suspend/resume
9706ccef5447 wifi: mt76: mt7921u: remove unnecessary MT76_STATE_SUSPEND
74a29eb4f714 wifi: mt76: mt7921: move mt7921_rx_check and mt7921_queue_rx_skb in mac.c
f49e06c4cfce wifi: mt76: sdio: fix the deadlock caused by sdio->stat_work
322656141fa4 wifi: mt76: sdio: poll sta stat when device transmits data
dee0a3cbfb03 wifi: mt76: mt7915: fix an uninitialized variable bug
9dd7be2c5164 wifi: mt76: mt7921: fix use after free in mt7921_acpi_read()
0ad02c9a4512 wifi: mt76: sdio: add rx_check callback for sdio devices
fe85e5ccbaca wifi: mt76: sdio: fix transmitting packet hangs
206c7ebd7464 wifi: mt76: mt7615: add mt7615_mutex_acquire/release in mt7615_sta_set_decap_offload
bf79f5d73e4f wifi: mt76: mt7915: fix possible unaligned access in mt7915_mac_add_twt_setup
c4132ab0bea2 wifi: mt76: connac: fix possible unaligned access in mt76_connac_mcu_add_nested_tlv
52eec74986cf wifi: mt76: mt7663s: add rx_check callback
019ef069e754 wifi: mt76: mt76_usb.mt76u_mcu.burst is always false remove related code
0a392ca03db8 wifi: mt76: mt7921: add mt7921_mutex_acquire at mt7921_[start, stop]_ap
fbb3554b6236 wifi: mt76: mt7921: add mt7921_mutex_acquire at mt7921_sta_set_decap_offload
b55a4eb2ee21 wifi: mt76: mt7921: fix the firmware version report
2d72c9a74011 wifi: mt76: move move mt76_sta_stats to mt76_wcid
873365b06c5c wifi: mt76: add PPDU based TxS support for WED device
0c64a80a61c2 wifi: mt76: connac: fix in comment
d11f971a452e wifi: mt76: mt7921: get rid of the false positive reset
2ac22300c7ac wifi: mt76: mt7915: fix mcs value in ht mode
5e45533e4ba2 wifi: mt76: fix uninitialized pointer in mt7921_mac_fill_rx
e06376af21dd wifi: mt76: mt7915: do not check state before configuring implicit beamform
0c0bda4aea05 wifi: mt76: mt7921: reset msta->airtime_ac while clearing up hw value
cddc4b43ea93 wifi: mt76: mt7921e: fix rmmod crash in driver reload test
ebbd68842ee0 wifi: mt76: mt7921: introduce Country Location Control support
763a1d90133b wifi: mt76: mt7921e: fix random fw download fail
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Wed, 14 Sep 2022 19:23:17 +0000 (20:23 +0100)]
mediatek: build USB XHCI support as module
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Olliver Schinagl [Wed, 31 Aug 2022 15:20:52 +0000 (17:20 +0200)]
realtek: rtl838x: Fix ethernet polling timeout on probe
Due to an oversight we accidentally inverted the timeout check. This
patch corrects this.
Fixes: 9cec4a0ea45b ("realtek: Use built-in functionality for timeout loop")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[ wrap poll_timeout line to 80 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Petr Štetiar [Fri, 22 Apr 2022 06:17:13 +0000 (08:17 +0200)]
armvirt: make 5.15 kernel default
In order to begin testing of upcoming kernel.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Fri, 22 Apr 2022 06:17:13 +0000 (08:17 +0200)]
malta: make 5.15 kernel default
In order to begin testing of upcoming kernel.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Wojciech Dubowik [Wed, 14 Sep 2022 10:13:10 +0000 (12:13 +0200)]
mpc85xx: Add 5.15 kernel as testing and fix configs
Build system: x86_64
Build-tested: generic
Run-tested: generic/TL-WDR4900 v1 board from TP-Link
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@westermo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [un-dmarc]
Wojciech Dubowik [Wed, 14 Sep 2022 10:12:06 +0000 (12:12 +0200)]
mpc85xx: Copy over kernel 5.10 patches and config to 5.15
Split patches for better change visibility.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@westermo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [un-dmarc, commit description]
Tomasz Maciej Nowak [Tue, 13 Sep 2022 20:38:09 +0000 (22:38 +0200)]
tegra: add kernel 5.15 support
- refresh config
- disable suspend as it's pointless in the sope of OpenWrt
- enable CPU frequency scaling
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 13 Sep 2022 20:38:08 +0000 (22:38 +0200)]
tegra: copy patches and config for kernel 5.15
Simple copy to better illustrate the forthcoming changes.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Rafał Miłecki [Wed, 14 Sep 2022 12:20:38 +0000 (14:20 +0200)]
bcm53xx: update NVMEM driver for NVRAM
Include support for NVMEM cells.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Olliver Schinagl [Wed, 31 Aug 2022 15:20:52 +0000 (17:20 +0200)]
realtek: Use built-in functionality for timeout loop
In commit
81e3017609be ("realtek: clean up rtl838x MDIO busy wait loop")
a hand-crafted loop was created, that nearly exactly replicate the
iopoll's `read_poll_timeout` functionality.
Use that instead.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Ansuel Smith [Tue, 6 Jul 2021 01:28:55 +0000 (03:28 +0200)]
scripts: add clean of build dir to dl_cleanup script
Improve dl_cleanup by adding an option to also clean the build directory
related to the downloaded package.
The script will check every directory in build_dir/ and check if any
old package is present there. If outdated package are found, the old
one are cleared leaving only the last one.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Tue, 6 Jul 2021 01:25:06 +0000 (03:25 +0200)]
scripts: assume dl/ the default dir for dl_cleanup script
Assume dl/ the default dl dir and make it configurable if someone have that in
a different place.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Thu, 31 Mar 2022 19:15:51 +0000 (21:15 +0200)]
scripts: add additional regex for dl_cleanup
Add additional regex for dl_cleanup script to handle
case with xxx-v1.2a and xxx-v1.2.3a
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ilya Katsnelson [Tue, 7 Jun 2022 07:23:31 +0000 (10:23 +0300)]
libcap: use more compatible shebang
Patch a script to use a shebang that works on systems that don't have
a /bin/bash, e.g. NixOS or GuixSD.
Signed-off-by: Ilya Katsnelson <me@0upti.me>
Ilya Katsnelson [Thu, 8 Sep 2022 09:04:05 +0000 (12:04 +0300)]
tools/bc: use more compatible shebang
Update the existing patch to use a shebang that works on systems that
don't have a /bin/bash, e.g. NixOS or GuixSD.
Signed-off-by: Ilya Katsnelson <me@0upti.me>
Kabuli Chana [Sun, 7 Aug 2022 23:05:51 +0000 (17:05 -0600)]
kernel: netsupport: Add FQ-PIE as an optional sched kmod and extract PIE
add Flow Queuing with Proportional Integral controller Enhanced (FQ-PIE) as an
optional kmod in network support and extract sched-pie from kmod-sched to
allow dependency on just kmod-sched-pie (PIE).
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Rosen Penev [Mon, 12 Sep 2022 07:59:13 +0000 (00:59 -0700)]
mt7621: fix Linksys E7350 GPIO
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.
Fixes: f4eef5f2a184 ("ramips: add support for Linksys E7350")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 12 Sep 2022 07:55:58 +0000 (00:55 -0700)]
mt7621: fix Belkin RT1800 GPIO
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.
Add back and and extra LEDs that were missing.
Tested all LEDs by turning them on.
Fixes: 26a6a6a60ba7 ("ramips: add support for Belkin RT1800")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Piotr Dymacz [Mon, 20 Jun 2022 11:13:30 +0000 (13:13 +0200)]
CI: include automatic Pull Request Labeler
This adds GitHub CI action which makes use of 'Labeler', allowing
automatic labeling of new PRs, based on the modified files paths.
Below labels are supported and more can be added later:
- 'target/*'
- 'target/imagebuilder'
- 'kernel'
- 'core packages'
- 'build/scripts/tools'
- 'toolchain'
- 'GitHub/CI'
For more information:
https://github.com/marketplace/actions/labeler
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Alexandru Gagniuc [Sat, 20 Aug 2022 18:49:52 +0000 (13:49 -0500)]
realtek: add support for TP-Link SG2210P
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Alexandru Gagniuc [Sat, 10 Sep 2022 20:48:22 +0000 (15:48 -0500)]
realtek: rtl8380-tl-sg2xxx: use a single "firmware" partition
The "firmware" partition was assembled from two contiguous partitions.
This complexity is unnecessary. Instead of using mtd-concat over
"sys" and "usrimg1", simply declare the "firmware" partition to cover
the flash space instead.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Alexandru Gagniuc [Sat, 20 Aug 2022 23:22:40 +0000 (18:22 -0500)]
realtek: tl-sg2xxx: read MAC address from nvmem-cells
The TP-Link RTL83xx based switches have their MAC address programmed
in the "para" partition. While in theory, the format of this partition
is dynamic, in practice, the MAC address appears to be located at a
consistent address. Thus, use nvmem-cells to read this MAC address.
The main MAC is required for deriving the MAC address of the switch
ports. Instead of reading it via mtd_get_mac_binary(), alias the
ethernet0 node as the label-mac-device, and use get_mac_label().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Alexandru Gagniuc [Mon, 29 Aug 2022 14:25:55 +0000 (09:25 -0500)]
realtek: rtl838x: label switch port dts nodes
Although PHY nodes are labeled, the port nodes were not. Labeling of
ports is useful for 'status = "disabled"' ports, which is supported
since commit
9a7f17e11f5d ("realtek: ignore disabled switch ports")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Alexandru Gagniuc [Sat, 20 Aug 2022 21:10:42 +0000 (16:10 -0500)]
realtek: split TP-Link SG2000 series devicetree
The TP-Link TL-SG2008, TL-SG2008P, and TL-SG2210P use the same board.
The main difference is that some footprints are not populated in the
lower-end models. To model this with minimal duplication, move the
devicetree to a common dtsi, leaving out just the board name.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[remove port relabelling from commit message, already merged with commit
18a2b29aa1c9 ("realtek: tl-sg2008p: fix labeling of lan ports")]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Petr Štetiar [Tue, 13 Sep 2022 07:06:50 +0000 (09:06 +0200)]
uboot-mediatek: fix extraneous right parens
Fixes following warning:
Makefile:310: extraneous text after 'ifeq' directive
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 13 Sep 2022 05:40:37 +0000 (07:40 +0200)]
scripts/download.pl: fix downloads with wget
Several users of wget for downloads (curl is not available in the
system) have reported broken download functionality:
wget --tries=5 --timeout=20 --output-document=- https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.142.tar.xz
http://: Invalid host name.
Thats all happening due to '' was passed as an argument, which got later
expanded to http://.
In the context of a list constructor '' is not nothing, it is an empty
string element. So fix it by using () as it will yield "nothing" and
thus not introduce an empty string element.
Fixes: #10692
Fixes: 90c6e3aedf16 ("scripts: always check certificates")
Signed-off-by: Jo-Philipp Wich <jo@mein.io> [shellwords() -> ()]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 13 Sep 2022 05:38:10 +0000 (07:38 +0200)]
scripts/download.pl: silence can't exec curl warning
When running build in verbose mode `make V=s` we can see a lot of
following warnings when curl is not available in the system:
Can't exec "curl": No such file or directory at scripts/download.pl line 77.
So lets fix it by redirecting of the stderr to null hole.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hauke Mehrtens [Sun, 11 Sep 2022 22:31:43 +0000 (00:31 +0200)]
toolchain: Include ./include/fortify for external musl toolchain
When building with an external toolcahin with musl also include
./include/fortify by default. This is also done when we build with the
internal toolchain using musl libc.
Without this extra include the fortify source feature is not working
when using an external musl toolchain. All binaries were compiled
without fortify source when an external musl toolchain was used. All
binaries release done by the OpenWrt project use the internal toolcahin
where fortify source is working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 11 Sep 2022 22:29:00 +0000 (00:29 +0200)]
toolchain: Select USE_SSTRIP with external musl toolchain
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Thu, 28 Jul 2022 11:40:12 +0000 (13:40 +0200)]
mac80211: rt2x00: experimental improvements for MT7620 wifi
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 12 Sep 2022 20:21:05 +0000 (21:21 +0100)]
mac80211: add patch descriptions to rt2x00 patches
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Mon, 12 Sep 2022 19:30:54 +0000 (21:30 +0200)]
unetd: only depend on bpf-headers if BPF toolchain support is available
If BPF is unavailable, unetd can be built without it (by disabling VXLAN support).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sergei Burakov [Fri, 20 May 2022 13:20:23 +0000 (16:20 +0300)]
ramips: add support for ZyXEL Keenetic 4G Rev.B Device
Specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
3x 10/100 Mbps Ethernet (2x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: Yes
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-4g-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@mail.ru>
Daniel Golle [Mon, 12 Sep 2022 13:10:26 +0000 (14:10 +0100)]
mediatek: unset CONFIG_CMDLINE_OVERRIDE for all targets but mt7629
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.
Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Yoonji Park [Mon, 6 Jun 2022 07:44:48 +0000 (07:44 +0000)]
mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
Yoonji Park [Sun, 5 Jun 2022 18:04:18 +0000 (18:04 +0000)]
kernel: add support for mtdsplit-fit offset
Support devices that has vendor custom header before FIT image.
Some devices has vendor custom header before FIT image. In this case mtd-
split can not find FIT image and it results in rootfs mount failure.
Please refer iptime,a6004mx device for further examples.
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
Daniel Golle [Mon, 12 Sep 2022 00:43:04 +0000 (01:43 +0100)]
firmware-utils: update to git HEAD
0c92b20 iptime-crc32: add support for A6004MX
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 12 Sep 2022 00:13:59 +0000 (01:13 +0100)]
xdp-tools: don't rely on host bpf headers
xdp-tools build currently breaks on build hosts which do not have
libbpf headers installed because the build system wrongly tries to
use the host's include path.
Properly pass path to libbpf headers to xdp-tools build system to
fix build e.g. on the buildbots.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shiji Yang [Wed, 7 Sep 2022 08:08:33 +0000 (16:08 +0800)]
mediatek: disable unsupported background radar detection
MT7915 requires an additional antenna for background radar scanning.
Disable this feature in the following devices that do not have a
separate DFS antenna:
linksys,e8450
ruijie,rg-ew3200gx-pro
xiaomi,redmi-router-ax6s
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Wed, 7 Sep 2022 08:08:33 +0000 (16:08 +0800)]
ramips: disable unsupported background radar detection
Background radar detection is not supported on devices that
using MT7905, so disable this feature in the following devices:
asus,rt-ax53u
jcg,q20
tplink,eap615-wall-v1
xiaomi,mi-router-cr6606
xiaomi,mi-router-cr6608
xiaomi,mi-router-cr6609
yuncore,ax820
Devices with MT7915 lacking a DFS antenna also do not support
background DFS:
totolink,x5000r
cudy,x6
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
projects / openwrt / staging / svanheule.git / log