ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
authorAndreas Böhler <dev@aboehler.at>
Mon, 10 Jul 2023 09:55:30 +0000 (11:55 +0200)
committerHauke Mehrtens <hauke@hauke-m.de>
Mon, 21 Aug 2023 19:41:12 +0000 (21:41 +0200)
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12
WiFi: 802.11a/b/g/n/ac SoC-integrated
USB: 1x 2.0

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m17
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd17 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 17
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Other Notes
===========

Contrary to the stock firmware, the USB port on the back can be used.

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit edfe91372adfdaf5ee4e294fb0f5860a16adc551)

target/linux/ipq40xx/base-files/etc/board.d/02_network
target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi [new file with mode: 0644]
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts
target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts [new file with mode: 0644]
target/linux/ipq40xx/image/generic.mk

index c297566dd85de092609ff6c3e65cd348650b0b94..77dc892d078874950d52f597a788eb6245fdd553 100644 (file)
@@ -108,7 +108,8 @@ ipq40xx_setup_interfaces()
        zte,mf286d)
                ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan"
                ;;
-       zte,mf287plus)
+       zte,mf287plus|\
+       zte,mf287pro)
                ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
                ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
                ;;
index f76fe9402df322c9b1c0805a394c32ecde5ad78f..2035d84993b7df1f9b3852ab38e8c33aea9a1c15 100644 (file)
@@ -36,6 +36,7 @@ wallys,dr40x9)
        ucidef_add_gpio_switch "sim_card_select" "SIM card select" "423" "0"
        ;;
 zte,mf286d|\
+zte,mf287pro|\
 zte,mf289f)
        ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0"
        ;;
index 8807f844e59aa3230f7c071dc7e347074975a985..83aac330ca2ddea3fde433eb6f8680cde326747c 100644 (file)
@@ -28,6 +28,7 @@ EOF
        zte,mf18a |\
        zte,mf286d |\
        zte,mf287plus |\
+       zte,mf287pro |\
        zte,mf289f)
                CI_UBIPART="rootfs"
                local mtdnum="$( find_mtd_index $CI_UBIPART )"
@@ -211,6 +212,7 @@ platform_do_upgrade() {
        zte,mf18a |\
        zte,mf286d |\
        zte,mf287plus |\
+       zte,mf287pro |\
        zte,mf289f)
                CI_UBIPART="rootfs"
                nand_do_upgrade "$1"
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi
new file mode 100644 (file)
index 0000000..3cbe2ea
--- /dev/null
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
+// Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
+// Copyright (c) 2023, Andreas Böhler <dev@aboehler.at>
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+       aliases {
+               led-boot = &led_status;
+               led-failsafe = &led_status;
+               led-running = &led_status;
+               led-upgrade = &led_status;
+       };
+
+       chosen {
+               /*
+                * bootargs forced by u-boot bootipq command:
+                * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
+                */
+               bootargs-append = " root=/dev/ubiblock0_1";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status: led-0 {
+                       label = "blue:power";
+                       function = LED_FUNCTION_POWER;
+                       color = <LED_COLOR_ID_BLUE>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               key_reset: key-reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+               };
+
+               key_wps: key-wps {
+                       label = "wps";
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+
+       soc {
+               rng@22000 {
+                       status = "okay";
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               tcsr@194b000 {
+                       /* select hostmode */
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+                       status = "okay";
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+       };
+};
+
+&mdio {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&blsp_dma {
+       status = "okay";
+};
+
+&usb2 {
+       status = "okay";
+};
+
+&usb3 {
+       status = "okay";
+};
+
+&blsp1_uart1 {
+       pinctrl-0 = <&serial_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+};
+
+&crypto {
+       status = "okay";
+};
+
+&cryptobam {
+       status = "okay";
+};
+
+&gmac {
+       status = "okay";
+       nvmem-cell-names = "mac-address";
+       nvmem-cells = <&macaddr_mac_0>;
+       mac-address-increment = <2>;
+};
+
+&switch {
+       status = "okay";
+};
+
+&swport2 {
+       status = "okay";
+
+       label = "lan1";
+};
+
+&swport3 {
+       status = "okay";
+
+       label = "lan2";
+};
+
+&swport4 {
+       status = "okay";
+
+       label = "lan3";
+};
+
+&swport5 {
+       status = "okay";
+
+       label = "lan4";
+};
+
+&qpic_bam {
+       status = "okay";
+};
+
+&usb2_hs_phy {
+       status = "okay";
+};
+
+&usb3_ss_phy {
+       status = "okay";
+};
+
+&usb3_hs_phy {
+       status = "okay";
+};
+
+&wifi0 {
+       status = "okay";
+       nvmem-cell-names = "pre-calibration", "mac-address";
+       nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
+       qcom,ath10k-calibration-variant = "zte,mf287plus";
+};
+
+&wifi1 {
+       status = "okay";
+       nvmem-cell-names = "pre-calibration", "mac-address";
+       nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
+       mac-address-increment = <1>;
+       qcom,ath10k-calibration-variant = "zte,mf287plus";
+};
index 6c285f4b8adaa4c524a5fa324ccd70539ea1d390..db8c8c9ad02a9f20668ccc610204f6fef3d29476 100644 (file)
@@ -3,31 +3,12 @@
 // Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
 // Copyright (c) 2023, Andreas Böhler <dev@aboehler.at>
 
-#include "qcom-ipq4019.dtsi"
-#include <dt-bindings/soc/qcom,tcsr.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
+#include "qcom-ipq4018-mf287.dtsi"
 
 / {
        model = "ZTE MF287Plus";
        compatible = "zte,mf287plus";
 
-       aliases {
-               led-boot = &led_status;
-               led-failsafe = &led_status;
-               led-running = &led_status;
-               led-upgrade = &led_status;
-       };
-
-       chosen {
-               /*
-                * bootargs forced by u-boot bootipq command:
-                * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
-                */
-               bootargs-append = " root=/dev/ubiblock0_1";
-       };
-
        /*
         * This node is used to restart modem module to avoid anomalous
         * behaviours on initial communication.
                compatible = "gpio-restart";
                gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
        };
-
-       leds {
-               compatible = "gpio-leds";
-
-               led_status: led-0 {
-                       label = "blue:power";
-                       function = LED_FUNCTION_POWER;
-                       color = <LED_COLOR_ID_BLUE>;
-                       gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
-               };
-       };
-
-       keys {
-               compatible = "gpio-keys";
-
-               key-reset {
-                       label = "reset";
-                       linux,code = <KEY_RESTART>;
-                       gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
-               };
-
-               key-wps {
-                       label = "wps";
-                       linux,code = <KEY_WPS_BUTTON>;
-                       gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
-               };
-       };
-
-       soc {
-               rng@22000 {
-                       status = "okay";
-               };
-
-               tcsr@1949000 {
-                       compatible = "qcom,tcsr";
-                       reg = <0x1949000 0x100>;
-                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
-               };
-
-               tcsr@194b000 {
-                       /* select hostmode */
-                       compatible = "qcom,tcsr";
-                       reg = <0x194b000 0x100>;
-                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
-                       status = "okay";
-               };
-
-               ess_tcsr@1953000 {
-                       compatible = "qcom,tcsr";
-                       reg = <0x1953000 0x1000>;
-                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
-               };
-
-               tcsr@1957000 {
-                       compatible = "qcom,tcsr";
-                       reg = <0x1957000 0x100>;
-                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
-               };
-       };
 };
 
-&mdio {
-       status = "okay";
+&key_reset {
+       gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
 };
 
-&watchdog {
-       status = "okay";
+&key_wps {
+       gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
 };
 
-&blsp_dma {
-       status = "okay";
-};
-
-&usb2 {
-       status = "okay";
-};
-
-&usb3 {
-       status = "okay";
+&led_status {
+       gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
 };
 
 &blsp1_spi1 {
        };
 };
 
-&blsp1_uart1 {
-       pinctrl-0 = <&serial_pins>;
-       pinctrl-names = "default";
-       status = "okay";
-};
-
-&crypto {
-       status = "okay";
-};
-
-&cryptobam {
-       status = "okay";
-};
-
-&gmac {
-       status = "okay";
-       nvmem-cell-names = "mac-address";
-       nvmem-cells = <&macaddr_mac_0>;
-       mac-address-increment = <2>;
-};
-
-&switch {
-       status = "okay";
-};
-
-&swport2 {
-       status = "okay";
-
-       label = "lan1";
-};
-
-&swport3 {
-       status = "okay";
-
-       label = "lan2";
-};
-
-&swport4 {
-       status = "okay";
-
-       label = "lan3";
-};
-
-&swport5 {
-       status = "okay";
-
-       label = "lan4";
-};
-
-&qpic_bam {
-       status = "okay";
-};
-
 &tlmm {
        serial_pins: serial_pinmux {
                mux {
                };
        };
 };
-
-&usb2_hs_phy {
-       status = "okay";
-};
-
-&usb3_ss_phy {
-       status = "okay";
-};
-
-&usb3_hs_phy {
-       status = "okay";
-};
-
-&wifi0 {
-       status = "okay";
-       nvmem-cell-names = "pre-calibration", "mac-address";
-       nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
-       qcom,ath10k-calibration-variant = "zte,mf287plus";
-};
-
-&wifi1 {
-       status = "okay";
-       nvmem-cell-names = "pre-calibration", "mac-address";
-       nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
-       mac-address-increment = <1>;
-       qcom,ath10k-calibration-variant = "zte,mf287plus";
-};
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts
new file mode 100644 (file)
index 0000000..dda0f74
--- /dev/null
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
+// Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
+// Copyright (c) 2023, Andreas Böhler <dev@aboehler.at>
+
+#include "qcom-ipq4018-mf287.dtsi"
+
+/ {
+       model = "ZTE MF287Pro";
+       compatible = "zte,mf287pro";
+
+       gpio_export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               modem {
+                       gpio-export,name = "modem-reset";
+                       gpio-export,output = <0>;
+                       gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       regulator-usb-vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "USB_VBUS";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               regulator-always-on;
+               regulator-boot-on;
+               gpio = <&tlmm 25 GPIO_ACTIVE_LOW>;
+       };
+};
+
+&key_reset {
+       gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+};
+
+&key_wps {
+       gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+};
+
+&led_status {
+       gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+};
+
+&mdio {
+       status = "okay";
+       pinctrl-0 = <&mdio_pins>;
+       pinctrl-names = "default";
+       reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+       reset-delay-us = <2000>;
+};
+
+&blsp1_spi1 {
+       pinctrl-0 = <&spi_0_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>,
+                               <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               reg = <0>;
+               spi-max-frequency = <24000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "0:SBL1";
+                               reg = <0x0 0x40000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "0:MIBIB";
+                               reg = <0x40000 0x20000>;
+                               read-only;
+                       };
+
+                       partition@60000 {
+                               label = "0:QSEE";
+                               reg = <0x60000 0x60000>;
+                               read-only;
+                       };
+
+                       partition@c0000 {
+                               label = "0:CDT";
+                               reg = <0xc0000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@d0000 {
+                               label = "0:DDRPARAMS";
+                               reg = <0xd0000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@e0000 {
+                               label = "0:APPSBLENV";
+                               reg = <0xe0000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@f0000 {
+                               label = "0:APPSBL";
+                               reg = <0xf0000 0xc0000>;
+                               read-only;
+                       };
+
+                       partition@1b0000 {
+                               label = "0:reserved1";
+                               reg = <0x1b0000 0x50000>;
+                               read-only;
+                       };
+               };
+       };
+
+       spi-nand@1 { /* flash@1 ? */
+               compatible = "spi-nand";
+               reg = <1>;
+               spi-max-frequency = <24000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "fota-flag";
+                               reg = <0x0 0xa0000>;
+                               read-only;
+                       };
+
+                       partition@a0000 {
+                               label = "ART";
+                               reg = <0xa0000 0x80000>;
+                               read-only;
+                               compatible = "nvmem-cells";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+
+                               precal_art_1000: precal@1000 {
+                                       reg = <0x1000 0x2f20>;
+                               };
+
+                               precal_art_5000: precal@5000 {
+                                       reg = <0x5000 0x2f20>;
+                               };
+                       };
+
+                       partition@120000 {
+                               label = "mac";
+                               reg = <0x120000 0x80000>;
+                               read-only;
+                               compatible = "nvmem-cells";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+
+                               macaddr_mac_0: macaddr@0 {
+                                       reg = <0x0 0x6>;
+                               };
+                       };
+
+                       partition@1a0000 {
+                               label = "reserved2";
+                               reg = <0x1a0000 0xc0000>;
+                       };
+
+                       partition@260000 {
+                               label = "cfg-param";
+                               reg = <0x260000 0x400000>;
+                               read-only;
+                       };
+
+                       partition@660000 {
+                               label = "log";
+                               reg = <0x660000 0x400000>;
+                       };
+
+                       partition@a60000 {
+                               label = "oops";
+                               reg = <0xa60000 0xa0000>;
+                       };
+
+                       partition@b00000 {
+                               label = "reserved3";
+                               reg = <0xb00000 0x500000>;
+                       };
+
+                       partition@1000000 {
+                               label = "web";
+                               reg = <0x1000000 0x800000>;
+                       };
+
+                       partition@1800000 {
+                               label = "rootfs";
+                               reg = <0x1800000 0x1d00000>;
+                       };
+
+                       partition@3500000 {
+                               label = "data";
+                               reg = <0x3500000 0x1900000>;
+                       };
+
+                       partition@4e00000 {
+                               label = "fota";
+                               reg = <0x4e00000 0x3200000>;
+                       };
+               };
+       };
+};
+
+&tlmm {
+       i2c_0_pins: i2c_0_pinmux {
+               mux {
+                       pins = "gpio20", "gpio21";
+                       function = "blsp_i2c0";
+                       bias-disable;
+               };
+       };
+
+       mdio_pins: mdio_pinmux {
+               mux_1 {
+                       pins = "gpio6";
+                       function = "mdio";
+                       bias-pull-up;
+               };
+
+               mux_2 {
+                       pins = "gpio7";
+                       function = "mdc";
+                       bias-pull-up;
+               };
+       };
+
+       serial_pins: serial_pinmux {
+               mux {
+                       pins = "gpio16", "gpio17";
+                       function = "blsp_uart0";
+                       bias-disable;
+               };
+       };
+
+       spi_0_pins: spi_0_pinmux {
+               pinmux {
+                       function = "blsp_spi0";
+                       pins = "gpio12", "gpio13", "gpio14", "gpio15";
+                       drive-strength = <12>;
+                       bias-disable;
+               };
+
+               pinmux_cs {
+                       function = "gpio";
+                       pins = "gpio12", "gpio54";
+                       drive-strength = <2>;
+                       bias-disable;
+                       output-high;
+               };
+       };
+};
index 907558302c70ddc06a9c51631ad718e1337b090d..7f4806b63d5040e447fc1e6546778dd823bf372a 100644 (file)
@@ -1162,12 +1162,8 @@ define Device/zte_mf286d
 endef
 TARGET_DEVICES += zte_mf286d
 
-define Device/zte_mf287plus
+define Device/zte_mf287_common
        $(call Device/zte_mf28x_common)
-       DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
-       DEVICE_MODEL := MF287Plus
-       DEVICE_ALT0_VENDOR := ZTE
-       DEVICE_ALT0_MODEL := MF287
        DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
        SOC := qcom-ipq4018
 #      The recovery image is used to return back to stock (an initramfs-based image
@@ -1178,8 +1174,23 @@ define Device/zte_mf287plus
        IMAGE/factory.bin  := append-ubi
        IMAGE/recovery.bin := append-squashfs4-fakeroot | sysupgrade-tar kernel=$$$$(BIN_DIR)/openwrt-$$(BOARD)$$(if $$(SUBTARGET),-$$(SUBTARGET))-$$(DEVICE_NAME)-initramfs-zImage.itb rootfs=$$$$@ | append-metadata
 endef
+
+define Device/zte_mf287plus
+       $(call Device/zte_mf287_common)
+       DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
+       DEVICE_MODEL := MF287Plus
+       DEVICE_ALT0_VENDOR := ZTE
+       DEVICE_ALT0_MODEL := MF287
+endef
 TARGET_DEVICES += zte_mf287plus
 
+define Device/zte_mf287pro
+       $(call Device/zte_mf287_common)
+       DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
+       DEVICE_MODEL := MF287Pro
+endef
+TARGET_DEVICES += zte_mf287pro
+
 define Device/zte_mf289f
        $(call Device/zte_mf28x_common)
        DEVICE_MODEL := MF289F