--- /dev/null
+
+ROM VER: 1.0.3
+CFG 01
+Readà
+ROM VER: 1.0.3
+CFG 01
+Read EEPROMX
+üHVCáU-Boot 1.0.5
+DRAM: 32 MB
+
+ relocate_code start
+ relocate code finish
+
+Entering flash_init()
+Flash: 8 MB
+env_relocate[226] malloced ENV at 81f80008
+env_relocate finished
+entering devices_init
+In: serial
+Out: serial
+Err: serial
+console_init_r finished!
+Net: danube Switch
+
+Type "run flash_nfs" to mount root filesystem over NFS
+
+Hit any key to stop autoboot: 3 \b\b\b 0
+DANUBE #
+Unknown command '<NULL>' - try 'help'
+DANUBE # printenv
+bootcmd=run flash_flash
+bootdelay=3
+baudrate=115200
+preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo
+ethaddr=00:01:22:33:44:55
+netdev=eth0
+baudrate=115200
+nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath)
+ramargs=setenv bootargs root=/dev/ram rw
+addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):on
+addmisc=setenv bootargs $(bootargs) console=ttyS1,$(baudrate) ethaddr=$(ethaddr) mem=31M panic=1
+flash_nfs=run nfsargs addip addmisc;bootm $(kernel_addr)
+flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)
+net_nfs=tftp 80500000 $(bootfile);run nfsargs addip addmisc;bootm
+net_ram=tftp 80500000 $(bootfile);run ramargs addip addmisc;bootm
+net_flash=tftp 80500000 $(bootfile);run flashargs addip addmisc;bootm
+flash_flash=run flashargs addip addmisc; bootm $(f_kernel_addr)
+rootpath=/mnt/danube_rootfs
+bootfile=uImage
+kernel_addr=80500000
+ramdisk_addr=B0100000
+u-boot=/tftpboot/danube/u-boot.bin
+load=tftp 80500000 $(u-boot)
+update=protect off 1:0-2;era 1:0-2;cp.b 80500000 B0000000 $(filesize)
+flashargs=setenv bootargs root=/dev/mtdblock2
+update_uboot=tftpboot 80500000 u-boot.bin;erase b0000000 b002ffff;cp.b 80500000 b0000000 $(filesize)
+update_rootfs=tftpboot 80500000 rootfs.img;upgrade rootfs 80500000 $(filesize) 0
+update_kernel=tftpboot 80500000 uImage;erase $(f_kernel_addr) b03bffff;cp.b 80500000 $(f_kernel_addr) $(filesize)
+update_firmware=tftpboot 80500000 firmware.img;upgrade firmware 80500000 $(filesize) 0
+reset_uboot_config=erase b0030000 b004ffff
+f_uboot_addr=0xb0000000
+f_uboot_size=0x30000
+f_firmware_addr=0xb03c0000
+f_firmware_size=0x40000
+f_rootfs_addr=0xb0050000
+f_rootfs_size=0x280000
+f_rootfs_end=0xb02cffff
+f_kernel_addr=0xb02d0000
+f_kernel_size=0xf0000
+f_kernel_end=0xb03bffff
+f_sysconfig_addr=0xb0400000
+f_sysconfig_size=0x10000
+f_voip_addr=0xb0410000
+f_voip_size=0x10000
+flash_end=0xb0420000
+part0_begin=0xB0000000
+part1_begin=0xB0030000
+part2_begin=0xB0050000
+part3_begin=0xB02F0000
+part4_begin=0xB03C0000
+part5_begin=0xB0400000
+part6_begin=0xB0410000
+total_part=7
+bootargs=root=/dev/mtdblock2 ip=172.20.80.23:172.20.80.237::::eth0:on console=ttyS1,115200 ethaddr=00:01:22:33:44:55 mem=31M panic=1
+filesize=1fd040
+ipaddr=10.10.10.10
+serverip=10.10.10.123
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 2356/131068 bytes
+DANUBE # flinfo
+
+Bank # 1: MXIC 29LV640BB (64 Mbit, boot sector SA0~SA126 size 64k bytes,other sectors SA127~SA135 size 8k bytes)
+ Size: 8 MB in 135 Sectors
+ Sector Start Addresses:
+ B0000000 B0002000 B0004000 B0006000 B0008000
+ B000A000 B000C000 B000E000 B0010000 B0020000
+ B0030000 B0040000 B0050000 B0060000 B0070000
+ B0080000 B0090000 B00A0000 B00B0000 B00C0000
+ B00D0000 B00E0000 B00F0000 B0100000 B0110000
+ B0120000 B0130000 B0140000 B0150000 B0160000
+ B0170000 B0180000 B0190000 B01A0000 B01B0000
+ B01C0000 B01D0000 B01E0000 B01F0000 B0200000
+ B0210000 B0220000 B0230000 B0240000 B0250000
+ B0260000 B0270000 B0280000 B0290000 B02A0000
+ B02B0000 B02C0000 B02D0000 B02E0000 B02F0000
+ B0300000 B0310000 B0320000 B0330000 B0340000
+ B0350000 B0360000 B0370000 B0380000 B0390000
+ B03A0000 B03B0000 B03C0000 B03D0000 B03E0000
+ B03F0000 B0400000 B0410000 B0420000 B0430000
+ B0440000 B0450000 B0460000 B0470000 B0480000
+ B0490000 B04A0000 B04B0000 B04C0000 B04D0000
+ B04E0000 B04F0000 B0500000 B0510000 B0520000
+ B0530000 B0540000 B0550000 B0560000 B0570000
+ B0580000 B0590000 B05A0000 B05B0000 B05C0000
+ B05D0000 B05E0000 B05F0000 B0600000 B0610000
+ B0620000 B0630000 B0640000 B0650000 B0660000
+ B0670000 B0680000 B0690000 B06A0000 B06B0000
+ B06C0000 B06D0000 B06E0000 B06F0000 B0700000
+ B0710000 B0720000 B0730000 B0740000 B0750000
+ B0760000 B0770000 B0780000 B0790000 B07A0000
+ B07B0000 B07C0000 B07D0000 B07E0000 B07F0000
+DANUBE #
+
+Bank # 1: MXIC 29LV640BB (64 Mbit, boot sector SA0~SA126 size 64k bytes,other sectors SA127~SA135 size 8k bytes)
+ Size: 8 MB in 135 Sectors
+ Sector Start Addresses:
+ B0000000 B0002000 B0004000 B0006000 B0008000
+ B000A000 B000C000 B000E000 B0010000 B0020000
+ B0030000 B0040000 B0050000 B0060000 B0070000
+ B0080000 B0090000 B00A0000 B00B0000 B00C0000
+ B00D0000 B00E0000 B00F0000 B0100000 B0110000
+ B0120000 B0130000 B0140000 B0150000 B0160000
+ B0170000 B0180000 B0190000 B01A0000 B01B0000
+ B01C0000 B01D0000 B01E0000 B01F0000 B0200000
+ B0210000 B0220000 B0230000 B0240000 B0250000
+ B0260000 B0270000 B0280000 B0290000 B02A0000
+ B02B0000 B02C0000 B02D0000 B02E0000 B02F0000
+ B0300000 B0310000 B0320000 B0330000 B0340000
+ B0350000 B0360000 B0370000 B0380000 B0390000
+ B03A0000 B03B0000 B03C0000 B03D0000 B03E0000
+ B03F0000 B0400000 B0410000 B0420000 B0430000
+ B0440000 B0450000 B0460000 B0470000 B0480000
+ B0490000 B04A0000 B04B0000 B04C0000 B04D0000
+ B04E0000 B04F0000 B0500000 B0510000 B0520000
+ B0530000 B0540000 B0550000 B0560000 B0570000
+ B0580000 B0590000 B05A0000 B05B0000 B05C0000
+ B05D0000 B05E0000 B05F0000 B0600000 B0610000
+ B0620000 B0630000 B0640000 B0650000 B0660000
+ B0670000 B0680000 B0690000 B06A0000 B06B0000
+ B06C0000 B06D0000 B06E0000 B06F0000 B0700000
+ B0710000 B0720000 B0730000 B0740000 B0750000
+ B0760000 B0770000 B0780000 B0790000 B07A0000
+ B07B0000 B07C0000 B07D0000 B07E0000 B07F0000
+DANUBE # run bootcmd
+## Booting image at b02d0000 ...
+ Image Name: MIPS Linux-2.4.31-Danube-3.0.3-G
+ Created: 2006-10-12 11:35:12 UTC
+ Image Type: MIPS Linux Kernel Image (gzip compressed)
+ Data Size: 854782 Bytes = 834.7 kB
+ Load Address: 80002000
+ Entry Point: 801ca040
+ Verifying Checksum ... OK
+ Uncompressing Kernel Image ... OK
+
+Starting kernel ...
+
+TODO: chip version
+memsize=32l
+flash_start=0xb0000000
+flash_size=8388608l
+Reserving memory for CP1 @0xa1f00000
+memsize=31
+CPU revision is: 00019641
+Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
+Primary data cache 16kB, 4-way, linesize 32 bytes.
+Linux version 2.4.31-Danube-3.0.3-G0432V30V (root@localhost) (gcc version 3.3.6) #2 å10æ\9c\88 12 19:35:05 CST 2006
+Can't analyze prologue code at 8001e360
+Determined physical RAM map:
+User-defined physical RAM map:
+ memory: 01f00000 @ 00000000 (usable)
+On node 0 totalpages: 7936
+zone(0): 7936 pages.
+zone(1): 0 pages.
+zone(2): 0 pages.
+Kernel command line: root=/dev/mtdblock2 ip=10.10.10.10:10.10.10.123::::eth0:on console=ttyS1,115200 ethaddr=00:01:22:33:44:55 mem=31M panic=1
+ethaddr_setup: mac address 0- 1-22-33-44-55
+mips_hpt_frequency:166666667
+r4k_offset: 00196e6a(1666666)
+Using 166.667 MHz high precision timer.
+Syam before calibrate_delay
+Calibrating delay loop...
+222.00 BogoMIPS
+Syam after calibrate_delay
+MIPS CPU counter frequency is fixed at 166666667 Hz
+Memory: 28728k/31744k available (1808k kernel code, 3016k reserved, 108k data, 100k init, 0k highmem)
+Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
+Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
+Mount cache hash table entries: 512 (order: 0, 4096 bytes)
+Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
+Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
+Checking for 'wait' instruction... unavailable.
+POSIX conformance testing by UNIFIX
+Linux NET4.0 for Linux 2.4
+Based upon Swansea University Computer Society NET3.039
+Initializing RT netlink socket
+LSP Revision 1
+Starting kswapd
+Squashfs 2.2 (released 2005/07/03) (C) 2002-2004, 2005 Phillip Lougher
+pty: 256 Unix98 ptys configured
+ttyS0 at MEM 0xbe100400 (irq = 2) is a IFX_ASC
+ttyS1 at MEM 0xbe100c00 (irq = 9) is a IFX_ASC
+<6>Danube PMU driver v0.3
+cgu: misc_register on minor = 63
+gptu: totally 6 16-bit timers/counters
+gptu: misc_register on minor 62
+gptu: succeeded to request irq 118
+gptu: succeeded to request irq 119
+gptu: succeeded to request irq 120
+gptu: succeeded to request irq 121
+gptu: succeeded to request irq 122
+gptu: succeeded to request irq 123
+led: misc_register on minor = 151
+memcopy_init: memcopy init
+loop: loaded (max 8 devices)
+PPP generic driver version 2.4.2
+danube MAC driver loaded!
+Loading 2nd ETH driver... init succeeded
+oamk: init_module() called.
+Opening oam kernel socket
+oamk: init_module() returned.
+init_danube_mtd: start_scan_addr: b0000000
+init_danube_mtd: chip probing count 0
+Danube: probing address:b0000000
+ Amd/Fujitsu Extended Query Table v1.1 at 0x0040
+number of CFI chips: 1
+cfi_cmdset_0002: Disabling fast programming due to code brokenness.
+init_danube_mtd: bank1, name:Danube Bank 0, size:8388608bytes
+DANUBE flash0: Using static image partition definition
+Creating 7 MTD partitions on "Danube Bank 0":
+0x00000000-0x00030000 : "U-Boot"
+0x00030000-0x00050000 : "Environment"
+0x00050000-0x002f0000 : "rootfs"
+0x002f0000-0x003c0000 : "Linux"
+0x003c0000-0x00400000 : "firmware"
+0x00400000-0x00410000 : "User-Data"
+0x00410000-0x00420000 : "voip-Data"
+Initializing Cryptographic API
+NET4: Linux TCP/IP 1.0 for NET4.0
+IP Protocols: ICMP, UDP, TCP, IGMP
+IP: routing cache hash table of 512 buckets, 4Kbytes
+TCP: Hash tables configured (established 2048 bind 4096)
+Linux IP multicast router 0.06 plus PIM-SM
+IP-Config: Guessing netmask 255.0.0.0
+IP-Config: Complete:
+ device=eth0, addr=10.10.10.10, mask=255.0.0.0, gw=255.255.255.255,
+ host=10.10.10.10, domain=, nis-domain=(none),
+ bootserver=10.10.10.123, rootserver=10.10.10.123, rootpath=
+ip_conntrack version 2.1 (248 buckets, 1984 max) - 624 bytes per conntrack
+ip_conntrack_pptp version 1.9 loaded
+ip_nat_pptp version 1.5 loaded
+ip_tables: (C) 2000-2002 Netfilter core team
+NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
+Ebtables v2.0 registered
+NET4: Ethernet Bridge 008 for NET4.0
+Bridge firewalling registered
+Danube Port Initialization
+DANUBE MIPS24KEc MPS mailbox driver, Version 1.1.0
+(c) Copyright 2006, Infineon Technologies AG
+IFX_MPS: using proc fs
+VFS: Mounted root (squashfs filesystem) readonly.
+Freeing unused kernel memory: 100k freed
+init started: BusyBox v1.00 (2006.10.12-11:36+0000) multi-call binary
+Algorithmics/MIPS FPU Emulator v1.5
+Created character device /dev/danube-port with major[247] and minor[0]
+1+0 records in
+1+0 records out
+Mount ADSL Firmware Now
+part_begin_addr=0xb0400000
+mtd_dev=/dev/mtd/5
+autoboot open /dev/danube/mei fail
+Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/net/ifx_nfext/ifx_nfext_core.o
+Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/net/ifx_nfext/ifx_nfext_ppp.o
+Using /lib/modules/2.4.31-Danube-3.0.3-G0432V30V/kernel/drivers/net/admmod.o
+Loading ADM6996 driver...
+
+6996I SMI Mode-Chip ID:71023
+ Bringing up syslog
+Bringing up klogd
+<6>device eth0 entered promiscuous mode
+br0: port 1(eth0) entering learning state
+br0: port 1(eth0) entering forwarding state
+br0: topology change detected, propagating
+--VDSL2 Pre Initialization --
+Init VDSL2 CPE Ref environment
+
+- loading VDSL2 CPE Ref Board - board driver -
+*** Creating dir: /dev/adm5120_rb
+*** Creating node: /dev/adm5120_rb/0
+Using ./drv_adm5120_rb
+cat: /proc/mei/version: No such file or directory
+ADM5120 Board Driver, Version 0.0.4.1
+<6>(c) Copyright 2003, Infineon Technologies AG
+
+- loading VDSL2 CPE board - DFE driver -
+*** Creating dir: /dev/vinax
+*** Creating node: /dev/vinax/cntrl0
+3.0.3-432-V30WV
+*** Creating node: /dev/vinax/0
+Using ./drv_vinax
+<6>VINAX Driver, Version 0.1.0.2
+<6>(c) Copyright 2005, Infineon Technologies AG
+<6>### VINAX - VINAX - VINAX - VINAX ###
+<7>VINAX_DRV: create proc config entry
+--> Add VINAX tick to timer queue
+
+board driver <drv_adm5120_rb> loaded
+--> AInitializes the MultiPort Memory Controller for the VDSL2 DFEBoard_InitIrq!
+mazon-Vinax test: open device: /dev/adm5120_rb/0.
+--> Amazon-Vinax test: close(3) device: //dev/adm5120_rb/0.
+current HW type is CPE_MODE
++++ setup CPE firmware vcpe_hw.bin +++
+ln: ./firmware.bin: File exists
+ln: ./firmware0.bin: File exists
+ln: ./firmware1.bin: File exists
+MEI driver <drv_vinax> loaded
+init Danube-Vinax MEI base addr=0x14000000 poVINAX_DRV[00]: ERROR - INIT DEVICE, HW failure
+lling mode
+!!! RESET the VDSL2 device (via MEI) !!!
+set VINAX DFE config
+VDSL2 pre init done
+---VDSL2 Post Initialization --
+VDSL2 initialisation - post
+Start VDSL2 CPE Ref environment
+Start VINAX firmeware download
+--> test: open device: /dev/vinax/0.
+<6>device nas1 entered promiscuous mode
+br0: port 2(nas1) entering learning state
+StartVINAX_DRV[00-01] Error ioctl - missing init, invalid cmd !!!
+ Download <firmware.bin>, size: 540148
+--> test: ERROR - ioct(FIO_VINAX_FW_DL), Operation not permitted, retCode = -1021
+Start VDSL2 DSL DAEMON Application
+DSL: start DSL daemon.
+DSL: DSL daemon running in background now!
+DSL: Device granularity is 1
+DSL: No firmware pointer
+DSL: No 2nd firmware pointer
+DSL: Given warmstart memory will be analyzed...
+DSL: ...No warmstart memory defined
+DSL: ...Using memory allocation via DSL_Malloc() for ALL data base sections
+DSL: ...Startup mode: COLDSTART
+DSL: No mapping information (line -> device channel) provided. Taking internal default settings.
+DSL[00]: VINAX init failed, no valid data
+DSL[00]: VINAX driver init failed
+DSL: Thread PID for thread tPM_Tick is 1006
+DSL:
+DSL: *****************************************************
+DSL: DSL library version: 1.5.1
+DSL: *****************************************************
+DSL: Number of devices : 1
+DSL: Number of lines : 1
+DSL: Number of lines/device : 1
+DSL: Number of channels/line : 2
+DSL:
+DSL: Memory usage of warm start resistent data base
+DSL: magic key data base : 4 bytes
+DSL: line config data base : 316 bytes
+DSL: channel config data base : 184 bytes
+DSL: line array config data base : 2424 bytes
+DSL: --------------
+DSL: Total : 2928 bytes
+DSL:
+DSL: Memory usage of status data base
+DSL: line status data base : 220 bytes
+DSL: channel status data base : 408 bytes
+DSL: --------------
+DSL: Total : 628 bytes
+DSL:
+DSL: Context memory usage
+DSL: context structure : 1128 bytes
+DSL: Timeout event lists : 32 bytes
+DSL: --------------
+DSL: Total : 1160 b<6>br0: port 2(nas1) entering forwarding state
+br0: topology change detected, propagating
+ytes
+DSL: *****************************************************
+DSL:
+DSL: Thread PID for thread tPipe_0 is 1007
+DSL: Thread PID for thread tPipe_1 is 1008
+iptables: No chain/target/match by that name
+iptables: No chain/target/match by that name
+DSL: Thread PID for thread tPipe_2 is 1015
+nReturn=0 nLine=0
+
+VDSL2 post init done
+device eth2 entered promiscuous mode
+br0: port 3(eth2) entering learning state
+installing mps devices...
+
++--------------------------------------+
+| Linux/MIPS on DANUBE by Infineon COM AC BB_CPE |
++--------------------------------------+
+br0: port 3(eth2) entering forwarding state
+br0: topology change detected, propagating
+
+danube login: root
+Password:
+Login incorrect
+danube login:
+Login ti
+danube login: admin
+Password:
+Login incorrect
+danube login: root
+Password:
+
+
+BusyBox v1.00 (2006.10.12-11:36+0000) Built-in shell (msh)
+Enter 'help' for a list of built-in commands.
+
+# lspci
+lspci: not found
+# \a
+\[ grep pwd
+adm6996 gunzip read_img
+basename gzip reboot
+br2684ctl hostname ripd
+br2684ctld httpd rm
+brctl ifconfig rmmod
+bringup_dns_relay ifx_util route
+bringup_oam inetd sh
+bringup_pppoa init sleep
+bringup_pppoe insmod snmpd
+bringup_wan iptables status_oper
+bringup_wan_service kill swreset
+busybox killall syslogd
+cat klogd tail
+chmod ln tar
+chroot logger tc
+cli_be login telnetd
+cli_fe logread test
+cmvread ls tftpd
+cmvwrite mem top
+cp mkdir touch
+cut mknod tr
+date mknod_util true
+dd modprobe.sh tty
+dmesg more udhcpc
+dnrd mount udhcpd
+dumpleases mpstat udhcpr
+echo msh umount
+env mv uname
+expr naptcfg upgrade
+false next_macaddr uptime
+fgrep oamctl usleep
+free oamd version.sh
+get_adsl_rate passwd vlanctl
+get_atmqos_name ping zcat
+get_if_index pppd
+getty ps
+# dmesg
+memsize=32l
+flash_start=0xb0000000
+flash_size=8388608l
+Reserving memory for CP1 @0xa1f00000
+memsize=31
+CPU revision is: 00019641
+Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
+Primary data cache 16kB, 4-way, linesize 32 bytes.
+Linux version 2.4.31-Danube-3.0.3-G0432V30V (root@localhost) (gcc version 3.3.6) #2 å10æ\9c\88 12 19:35:05 CST 2006
+Can't analyze prologue code at 8001e360
+Determined physical RAM map:
+User-defined physical RAM map:
+ memory: 01f00000 @ 00000000 (usable)
+On node 0 totalpages: 7936
+zone(0): 7936 pages.
+zone(1): 0 pages.
+zone(2): 0 pages.
+Kernel command line: root=/dev/mtdblock2 ip=10.10.10.10:10.10.10.123::::eth0:on console=ttyS1,115200 ethaddr=00:01:22:33:44:55 mem=31M panic=1
+ethaddr_setup: mac address 0- 1-22-33-44-55
+mips_hpt_frequency:166666667
+r4k_offset: 00196e6a(1666666)
+Using 166.667 MHz high precision timer.
+Syam before calibrate_delay
+Calibrating delay loop...
+Syam after calibrate_delay
+MIPS CPU counter frequency is fixed at 166666667 Hz
+Memory: 28728k/31744k available (1808k kernel code, 3016k reserved, 108k data, 100k init, 0k highmem)
+Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
+Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
+Mount cache hash table entries: 512 (order: 0, 4096 bytes)
+Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
+Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
+Checking for 'wait' instruction... unavailable.
+POSIX conformance testing by UNIFIX
+Linux NET4.0 for Linux 2.4
+Based upon Swansea University Computer Society NET3.039
+Initializing RT netlink socket
+LSP Revision 1
+Starting kswapd
+Squashfs 2.2 (released 2005/07/03) (C) 2002-2004, 2005 Phillip Lougher
+pty: 256 Unix98 ptys configured
+ttyS0 at MEM 0xbe100400 (irq = 2) is a IFX_ASC
+ttyS1 at MEM 0xbe100c00 (irq = 9) is a IFX_ASC
+<6>Danube PMU driver v0.3
+cgu: misc_register on minor = 63
+gptu: totally 6 16-bit timers/counters
+gptu: misc_register on minor 62
+gptu: succeeded to request irq 118
+gptu: succeeded to request irq 119
+gptu: succeeded to request irq 120
+gptu: succeeded to request irq 121
+gptu: succeeded to request irq 122
+gptu: succeeded to request irq 123
+led: misc_register on minor = 151
+memcopy_init: memcopy init
+loop: loaded (max 8 devices)
+PPP generic driver version 2.4.2
+danube MAC driver loaded!
+Loading 2nd ETH driver... init succeeded
+oamk: init_module() called.
+Opening oam kernel socket
+oamk: init_module() returned.
+init_danube_mtd: start_scan_addr: b0000000
+init_danube_mtd: chip probing count 0
+Danube: probing address:b0000000
+ Amd/Fujitsu Extended Query Table v1.1 at 0x0040
+number of CFI chips: 1
+cfi_cmdset_0002: Disabling fast programming due to code brokenness.
+init_danube_mtd: bank1, name:Danube Bank 0, size:8388608bytes
+DANUBE flash0: Using static image partition definition
+Creating 7 MTD partitions on "Danube Bank 0":
+0x00000000-0x00030000 : "U-Boot"
+0x00030000-0x00050000 : "Environment"
+0x00050000-0x002f0000 : "rootfs"
+0x002f0000-0x003c0000 : "Linux"
+0x003c0000-0x00400000 : "firmware"
+0x00400000-0x00410000 : "User-Data"
+0x00410000-0x00420000 : "voip-Data"
+Initializing Cryptographic API
+NET4: Linux TCP/IP 1.0 for NET4.0
+IP Protocols: ICMP, UDP, TCP, IGMP
+IP: routing cache hash table of 512 buckets, 4Kbytes
+TCP: Hash tables configured (established 2048 bind 4096)
+Linux IP multicast router 0.06 plus PIM-SM
+IP-Config: Guessing netmask 255.0.0.0
+IP-Config: Complete:
+ device=eth0, addr=10.10.10.10, mask=255.0.0.0, gw=255.255.255.255,
+ host=10.10.10.10, domain=, nis-domain=(none),
+ bootserver=10.10.10.123, rootserver=10.10.10.123, rootpath=
+ip_conntrack version 2.1 (248 buckets, 1984 max) - 624 bytes per conntrack
+ip_conntrack_pptp version 1.9 loaded
+ip_nat_pptp version 1.5 loaded
+ip_tables: (C) 2000-2002 Netfilter core team
+NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
+Ebtables v2.0 registered
+NET4: Ethernet Bridge 008 for NET4.0
+Bridge firewalling registered
+Danube Port Initialization
+DANUBE MIPS24KEc MPS mailbox driver, Version 1.1.0
+(c) Copyright 2006, Infineon Technologies AG
+IFX_MPS: using proc fs
+VFS: Mounted root (squashfs filesystem) readonly.
+Freeing unused kernel memory: 100k freed
+Algorithmics/MIPS FPU Emulator v1.5
+Loading ADM6996 driver...
+
+6996I SMI Mode-Chip ID:71023
+ <6>device eth0 entered promiscuous mode
+br0: port 1(eth0) entering learning state
+br0: port 1(eth0) entering forwarding state
+br0: topology change detected, propagating
+ADM5120 Board Driver, Version 0.0.4.1
+<6>(c) Copyright 2003, Infineon Technologies AG
+<6>VINAX Driver, Version 0.1.0.2
+<6>(c) Copyright 2005, Infineon Technologies AG
+<6>### VINAX - VINAX - VINAX - VINAX ###
+<7>VINAX_DRV: create proc config entry
+--> Add VINAX tick to timer queue
+Initializes the MultiPort Memory Controller for the VDSL2 DFEBoard_InitIrq!
+VINAX_DRV[00]: ERROR - INIT DEVICE, HW failure
+<6>device nas1 entered promiscuous mode
+br0: port 2(nas1) entering learning state
+VINAX_DRV[00-01] Error ioctl - missing init, invalid cmd !!!
+<6>br0: port 2(nas1) entering forwarding state
+br0: topology change detected, propagating
+device eth2 entered promiscuous mode
+br0: port 3(eth2) entering learning state
+br0: port 3(eth2) entering forwarding state
+br0: topology change detected, propagating
+# ls /p\b\b# ls /proc/
+1 4 cpuinfo eth2 loadavg slabinfo
+1005 5 crypto execdomains locks stat
+1006 6 danube_bcu filesystems lspinfo swaps
+1007 67 danube_dma fs meminfo sys
+1008 7 danube_etop interrupts misc sysvipc
+1015 74 danube_pmu iomem modules tty
+1039 80 danube_rcu ioports mounts uptime
+1042 808 danube_wdt irq mtd version
+17 994 devices kcore net
+2 bus dma kmsg partitions
+3 cmdline driver ksyms self
+# mount
+/dev/root on / type squashfs (ro)
+proc on /proc type proc (rw)
+/dev/ram on /ramdisk type ramfs (rw)
+/dev/ram on /dev type ramfs (rw)
+/dev/mtdblock/4 on /firmware type squashfs (ro)
+# cat /p\b\b# cat /proc/bu# cat /proc/bus/p\ac\a\b \b\a\b \b\a\b \b\b \b\b \b\b \b\a# cat /proc/
+/proc/1/ /proc/80/ /proc/eth2/ /proc/modules
+/proc/1005/ /proc/808/ /proc/execdomains /proc/mounts
+/proc/1006/ /proc/994/ /proc/filesystems /proc/mtd
+/proc/1007/ /proc/bus/ /proc/fs/ /proc/net/
+/proc/1008/ /proc/cmdline /proc/interrupts /proc/partitions
+/proc/1015/ /proc/cpuinfo /proc/iomem /proc/self/
+/proc/1039/ /proc/crypto /proc/ioports /proc/slabinfo
+/proc/17/ /proc/danube_bcu /proc/irq/ /proc/stat
+/proc/2/ /proc/danube_dma/ /proc/kcore /proc/swaps
+/proc/3/ /proc/danube_etop/ /proc/kmsg /proc/sys/
+/proc/4/ /proc/danube_pmu /proc/ksyms /proc/sysvipc/
+/proc/5/ /proc/danube_rcu /proc/loadavg /proc/tty/
+/proc/6/ /proc/danube_wdt /proc/locks /proc/uptime
+/proc/67/ /proc/devices /proc/lspinfo/ /proc/version
+/proc/7/ /proc/dma /proc/meminfo
+/proc/74/ /proc/driver/ /proc/misc
+# cat /proc/bu# cat /proc/bus/\a
+cat: Read error: Is a directory
+# # cat /proc/bus/at /proc/bus/ t /proc/bus/ /proc/bus/ l /proc/bus/s /proc/bus/ /proc/bus/
+# cat /p\b\b# cat /proc/mem# cat /proc/meminfo
+ total: used: free: shared: buffers: cached:
+Mem: 29519872 10489856 19030016 0 1298432 4550656
+Swap: 0 0 0
+MemTotal: 28828 kB
+MemFree: 18584 kB
+MemShared: 0 kB
+Buffers: 1268 kB
+Cached: 4444 kB
+SwapCached: 0 kB
+Active: 2780 kB
+Inactive: 2956 kB
+HighTotal: 0 kB
+HighFree: 0 kB
+LowTotal: 28828 kB
+LowFree: 18584 kB
+SwapTotal: 0 kB
+SwapFree: 0 kB
+# cat /p\b\b# cat /proc/cp# cat /proc/cpuinfo
+system type : DANUBE
+processor : 0
+cpu model : unknown V4.1
+BogoMIPS : 222.00
+wait instruction : no
+microsecond timers : yes
+tlb_entries : 16
+extra interrupt vector : yes
+hardware watchpoint : yes
+VCED exceptions : not available
+VCEI exceptions : not available
+#
\ No newline at end of file
projects / openwrt / svn-archive / docs.git / commitdiff