target/linux/kirkwood/patches-5.15/113-readynas_duo_v2.patch

   1 --- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
   2 +++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
   3 @@ -19,6 +19,13 @@
   4                 reg = <0x00000000 0x10000000>;
   5         };
   6
   7 +       aliases {
   8 +               led-boot = &led_power;
   9 +               led-failsafe = &led_power;
  10 +               led-running = &led_power;
  11 +               led-upgrade = &led_power;
  12 +       };
  13 +
  14         chosen {
  15                 bootargs = "console=ttyS0,115200n8 earlyprintk";
  16                 stdout-path = &uart0;
  17 @@ -115,7 +122,7 @@
  18                               &pmx_led_blue_backup >;
  19                 pinctrl-names = "default";
  20
  21 -               power_led {
  22 +               led_power: power_led {
  23                         label = "status:blue:power_led";
  24                         gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
  25                         default-state = "keep";
  26 @@ -129,11 +136,13 @@
  27                 disk1_led {
  28                         label = "status:blue:disk1_led";
  29                         gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
  30 +                       linux,default-trigger = "ata1";
  31                 };
  32
  33                 disk2_led {
  34                         label = "status:blue:disk2_led";
  35                         gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
  36 +                       linux,default-trigger = "ata2";
  37                 };
  38
  39                 backup_led {
  40 @@ -150,7 +159,13 @@
  41
  42                 power-button {
  43                         label = "Power Button";
  44 -                       linux,code = <KEY_POWER>;
  45 +                       /* Power button and INT pin from PHY are both connected
  46 +                        * to this GPIO. Every network restart causes PHY restart
  47 +                        * and button is pressed. It's difficult to use it as
  48 +                        * KEY_POWER without changes in kernel (or netifd) so
  49 +                        * the button is configured as regular one.
  50 +                        */
  51 +                       linux,code = <BTN_1>;
  52                         gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
  53                 };
  54
  55 @@ -208,18 +223,13 @@
  56         };
  57
  58         partition@200000 {
  59 -               label = "uImage";
  60 +               label = "kernel";
  61                 reg = <0x0200000 0x600000>;
  62         };
  63
  64         partition@800000 {
  65 -               label = "minirootfs";
  66 -               reg = <0x0800000 0x1000000>;
  67 -       };
  68 -
  69 -       partition@1800000 {
  70 -               label = "jffs2";
  71 -               reg = <0x1800000 0x6800000>;
  72 +               label = "ubi";
  73 +               reg = <0x0800000 0x7800000>;
  74         };
  75  };
  76