target/linux/generic/backport-6.6/790-09-v6.9-net-dsa-mt7530-improve-code-path-for-setting-up-port.patch

   1 From c1b2294a9b4b9b6c0cbe58666cb86e0a9cb0abfd Mon Sep 17 00:00:00 2001
   2 From: =?UTF-8?q?Ar=C4=B1n=C3=A7=20=C3=9CNAL?= <arinc.unal@arinc9.com>
   3 Date: Mon, 22 Jan 2024 08:35:56 +0300
   4 Subject: [PATCH 09/30] net: dsa: mt7530: improve code path for setting up port
   5  5
   6 MIME-Version: 1.0
   7 Content-Type: text/plain; charset=UTF-8
   8 Content-Transfer-Encoding: 8bit
   9
  10 There're two code paths for setting up port 5:
  11
  12 mt7530_setup()
  13 -> mt7530_setup_port5()
  14
  15 mt753x_phylink_mac_config()
  16 -> mt753x_mac_config()
  17    -> mt7530_mac_config()
  18       -> mt7530_setup_port5()
  19
  20 Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
  21 is used as a CPU, DSA, or user port, mt7530_setup_port5() from
  22 mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
  23 set on mt7530_setup_port5() will match state->interface on
  24 mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
  25 again.
  26
  27 Therefore, mt7530_setup_port5() will never run from
  28 mt753x_phylink_mac_config().
  29
  30 Address this by not running mt7530_setup_port5() from mt7530_setup() if
  31 port 5 is used as a CPU, DSA, or user port. This driver isn't in the
  32 dsa_switches_apply_workarounds[] array so phylink will always be present.
  33
  34 To keep the cases where port 5 isn't controlled by phylink working as
  35 before, preserve the mt7530_setup_port5() call from mt7530_setup().
  36
  37 Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
  38 "priv" is allocated.
  39
  40 Move setting the interface to a more specific location. It's supposed to be
  41 overwritten if PHY muxing is detected.
  42
  43 Improve the comment which explains the process.
  44
  45 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
  46 Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
  47 Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
  48 Signed-off-by: Jakub Kicinski <kuba@kernel.org>
  49 ---
  50  drivers/net/dsa/mt7530.c | 17 ++++++++---------
  51  1 file changed, 8 insertions(+), 9 deletions(-)
  52
  53 --- a/drivers/net/dsa/mt7530.c
  54 +++ b/drivers/net/dsa/mt7530.c
  55 @@ -2362,16 +2362,15 @@ mt7530_setup(struct dsa_switch *ds)
  56                 return ret;
  57
  58         /* Setup port 5 */
  59 -       priv->p5_intf_sel = P5_DISABLED;
  60 -       interface = PHY_INTERFACE_MODE_NA;
  61 -
  62         if (!dsa_is_unused_port(ds, 5)) {
  63                 priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
  64 -               ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
  65 -               if (ret && ret != -ENODEV)
  66 -                       return ret;
  67         } else {
  68 -               /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
  69 +               /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
  70 +                * Set priv->p5_intf_sel to the appropriate value if PHY muxing
  71 +                * is detected.
  72 +                */
  73 +               interface = PHY_INTERFACE_MODE_NA;
  74 +
  75                 for_each_child_of_node(dn, mac_np) {
  76                         if (!of_device_is_compatible(mac_np,
  77                                                      "mediatek,eth-mac"))
  78 @@ -2402,6 +2401,8 @@ mt7530_setup(struct dsa_switch *ds)
  79                         of_node_put(phy_node);
  80                         break;
  81                 }
  82 +
  83 +               mt7530_setup_port5(ds, interface);
  84         }
  85
  86  #ifdef CONFIG_GPIOLIB
  87 @@ -2412,8 +2413,6 @@ mt7530_setup(struct dsa_switch *ds)
  88         }
  89  #endif /* CONFIG_GPIOLIB */
  90
  91 -       mt7530_setup_port5(ds, interface);
  92 -
  93         /* Flush the FDB table */
  94         ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
  95         if (ret < 0)