target/linux/brcm2708/patches-4.19/950-0813-overlays-Add-sh1106-spi-and-ssd1351-spi-overlays-344.patch

   1 From 1b8ea7066ee06404e0148702bc3e85a191f6d867 Mon Sep 17 00:00:00 2001
   2 From: MikeDK <m.kaplan@evva.com>
   3 Date: Fri, 31 Jan 2020 12:45:43 +0100
   4 Subject: [PATCH] overlays: Add sh1106-spi and ssd1351-spi overlays
   5  (#3442)
   6
   7 Add overlays for SH1106 and SSD1351 based OLED displays.
   8 SH1106 is present in many 1.3 inch OLEDs and SSD1351 is present in
   9 1.5 inch RGB OLEDs from AliExpress.
  10
  11 This will load the staging fbtft drivers.
  12
  13 Signed-off-by: Michael Kaplan <m.kaplan@evva.com>
  14 ---
  15  arch/arm/boot/dts/overlays/Makefile           |  2 +
  16  arch/arm/boot/dts/overlays/README             | 23 ++++++
  17  .../boot/dts/overlays/sh1106-spi-overlay.dts  | 82 +++++++++++++++++++
  18  .../boot/dts/overlays/ssd1351-spi-overlay.dts | 81 ++++++++++++++++++
  19  4 files changed, 188 insertions(+)
  20  create mode 100644 arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts
  21  create mode 100644 arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts
  22
  23 --- a/arch/arm/boot/dts/overlays/Makefile
  24 +++ b/arch/arm/boot/dts/overlays/Makefile
  25 @@ -145,6 +145,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
  26         sdhost.dtbo \
  27         sdio.dtbo \
  28         sdtweak.dtbo \
  29 +       sh1106-spi.dtbo \
  30         smi.dtbo \
  31         smi-dev.dtbo \
  32         smi-nand.dtbo \
  33 @@ -169,6 +170,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
  34         spi6-2cs.dtbo \
  35         ssd1306.dtbo \
  36         ssd1306-spi.dtbo \
  37 +       ssd1351-spi.dtbo \
  38         superaudioboard.dtbo \
  39         sx150x.dtbo \
  40         tc358743.dtbo \
  41 --- a/arch/arm/boot/dts/overlays/README
  42 +++ b/arch/arm/boot/dts/overlays/README
  43 @@ -2145,6 +2145,18 @@ Params: overclock_50            Clock (i
  44                                  (default on)
  45
  46
  47 +Name:   sh1106-spi
  48 +Info:   Overlay for SH1106 OLED via SPI using fbtft staging driver.
  49 +Load:   dtoverlay=sh1106-spi,<param>=<val>
  50 +Params: speed                   SPI bus speed (default 4000000)
  51 +        rotate                  Display rotation (0, 90, 180 or 270; default 0)
  52 +        fps                     Delay between frame updates (default 25)
  53 +        debug                   Debug output level (0-7; default 0)
  54 +        dc_pin                  GPIO pin for D/C (default 24)
  55 +        reset_pin               GPIO pin for RESET (default 25)
  56 +        height                  Display height (32 or 64; default 64)
  57 +
  58 +
  59  Name:   smi
  60  Info:   Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25!
  61  Load:   dtoverlay=smi
  62 @@ -2440,6 +2452,17 @@ Params: speed                   SPI bus
  63          height                  Display height (32 or 64; default 64)
  64
  65
  66 +Name:   ssd1351-spi
  67 +Info:   Overlay for SSD1351 OLED via SPI using fbtft staging driver.
  68 +Load:   dtoverlay=ssd1351-spi,<param>=<val>
  69 +Params: speed                   SPI bus speed (default 4500000)
  70 +        rotate                  Display rotation (0, 90, 180 or 270; default 0)
  71 +        fps                     Delay between frame updates (default 25)
  72 +        debug                   Debug output level (0-7; default 0)
  73 +        dc_pin                  GPIO pin for D/C (default 24)
  74 +        reset_pin               GPIO pin for RESET (default 25)
  75 +
  76 +
  77  Name:   superaudioboard
  78  Info:   Configures the SuperAudioBoard sound card
  79  Load:   dtoverlay=superaudioboard,<param>=<val>
  80 --- /dev/null
  81 +++ b/arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts
  82 @@ -0,0 +1,82 @@
  83 +/*
  84 + * Device Tree overlay for SH1106 based SPI OLED display
  85 + *
  86 + */
  87 +
  88 +/dts-v1/;
  89 +/plugin/;
  90 +
  91 +/ {
  92 +       compatible = "brcm,bcm2835";
  93 +
  94 +       fragment@0 {
  95 +               target = <&spi0>;
  96 +               __overlay__ {
  97 +                       status = "okay";
  98 +               };
  99 +       };
 100 +
 101 +       fragment@1 {
 102 +               target = <&spidev0>;
 103 +               __overlay__ {
 104 +                       status = "disabled";
 105 +               };
 106 +       };
 107 +
 108 +       fragment@2 {
 109 +               target = <&spidev1>;
 110 +               __overlay__ {
 111 +                       status = "disabled";
 112 +               };
 113 +       };
 114 +
 115 +       fragment@3 {
 116 +               target = <&gpio>;
 117 +               __overlay__ {
 118 +                       sh1106_pins: sh1106_pins {
 119 +                                brcm,pins = <25 24>;
 120 +                                brcm,function = <1 1>; /* out out */
 121 +                       };
 122 +               };
 123 +       };
 124 +
 125 +       fragment@4 {
 126 +               target = <&spi0>;
 127 +               __overlay__ {
 128 +                       /* needed to avoid dtc warning */
 129 +                       #address-cells = <1>;
 130 +                       #size-cells = <0>;
 131 +
 132 +                       sh1106: sh1106@0{
 133 +                               compatible = "sinowealth,sh1106";
 134 +                               reg = <0>;
 135 +                               pinctrl-names = "default";
 136 +                               pinctrl-0 = <&sh1106_pins>;
 137 +
 138 +                               spi-max-frequency = <4000000>;
 139 +                               bgr = <0>;
 140 +                               bpp = <1>;
 141 +                               rotate = <0>;
 142 +                               fps = <25>;
 143 +                               buswidth = <8>;
 144 +                               reset-gpios = <&gpio 25 0>;
 145 +                               dc-gpios = <&gpio 24 0>;
 146 +                               debug = <0>;
 147 +
 148 +                               sinowealth,height = <64>;
 149 +                               sinowealth,width = <128>;
 150 +                               sinowealth,page-offset = <0>;
 151 +                       };
 152 +               };
 153 +       };
 154 +
 155 +       __overrides__ {
 156 +               speed           = <&sh1106>,"spi-max-frequency:0";
 157 +               rotate          = <&sh1106>,"rotate:0";
 158 +               fps             = <&sh1106>,"fps:0";
 159 +               debug           = <&sh1106>,"debug:0";
 160 +               dc_pin          = <&sh1106>,"dc-gpios:4>";
 161 +               reset_pin       = <&sh1106>,"reset-gpios:4>";
 162 +               height          = <&sh1106>,"sinowealth,height:0>";
 163 +       };
 164 +};
 165 --- /dev/null
 166 +++ b/arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts
 167 @@ -0,0 +1,81 @@
 168 +/*
 169 + * Device Tree overlay for SSD1351 based SPI OLED display
 170 + *
 171 + */
 172 +
 173 +/dts-v1/;
 174 +/plugin/;
 175 +
 176 +/ {
 177 +       compatible = "brcm,bcm2835";
 178 +
 179 +       fragment@0 {
 180 +               target = <&spi0>;
 181 +               __overlay__ {
 182 +                       status = "okay";
 183 +               };
 184 +       };
 185 +
 186 +       fragment@1 {
 187 +               target = <&spidev0>;
 188 +               __overlay__ {
 189 +                       status = "disabled";
 190 +               };
 191 +       };
 192 +
 193 +       fragment@2 {
 194 +               target = <&spidev1>;
 195 +               __overlay__ {
 196 +                       status = "disabled";
 197 +               };
 198 +       };
 199 +
 200 +       fragment@3 {
 201 +               target = <&gpio>;
 202 +               __overlay__ {
 203 +                       ssd1351_pins: ssd1351_pins {
 204 +                                brcm,pins = <25 24>;
 205 +                                brcm,function = <1 1>; /* out out */
 206 +                       };
 207 +               };
 208 +       };
 209 +
 210 +       fragment@4 {
 211 +               target = <&spi0>;
 212 +               __overlay__ {
 213 +                       /* needed to avoid dtc warning */
 214 +                       #address-cells = <1>;
 215 +                       #size-cells = <0>;
 216 +
 217 +                       ssd1351: ssd1351@0{
 218 +                               compatible = "solomon,ssd1351";
 219 +                               reg = <0>;
 220 +                               pinctrl-names = "default";
 221 +                               pinctrl-0 = <&ssd1351_pins>;
 222 +
 223 +                               spi-max-frequency = <4500000>;
 224 +                               bgr = <0>;
 225 +                               bpp = <16>;
 226 +                               rotate = <0>;
 227 +                               fps = <25>;
 228 +                               buswidth = <8>;
 229 +                               reset-gpios = <&gpio 25 0>;
 230 +                               dc-gpios = <&gpio 24 0>;
 231 +                               debug = <0>;
 232 +
 233 +                               solomon,height = <128>;
 234 +                               solomon,width = <128>;
 235 +                               solomon,page-offset = <0>;
 236 +                       };
 237 +               };
 238 +       };
 239 +
 240 +       __overrides__ {
 241 +               speed           = <&ssd1351>,"spi-max-frequency:0";
 242 +               rotate          = <&ssd1351>,"rotate:0";
 243 +               fps             = <&ssd1351>,"fps:0";
 244 +               debug           = <&ssd1351>,"debug:0";
 245 +               dc_pin          = <&ssd1351>,"dc-gpios:4>";
 246 +               reset_pin       = <&ssd1351>,"reset-gpios:4>";
 247 +       };
 248 +};