target/linux/ramips/dts/mt7621_planex_vr500.dts

   1 #include "mt7621.dtsi"
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 / {
   7         compatible = "planex,vr500", "mediatek,mt7621-soc";
   8         model = "Planex VR500";
   9
  10         aliases {
  11                 led-boot = &led_power;
  12                 led-failsafe = &led_power;
  13                 led-running = &led_power;
  14                 led-upgrade = &led_power;
  15         };
  16
  17         leds {
  18                 compatible = "gpio-leds";
  19
  20                 led_power: power {
  21                         label = "green:power";
  22                         gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
  23                 };
  24         };
  25
  26         keys {
  27                 compatible = "gpio-keys";
  28
  29                 reset {
  30                         label = "reset";
  31                         gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
  32                         linux,code = <KEY_RESTART>;
  33                 };
  34         };
  35 };
  36
  37 &spi0 {
  38         status = "okay";
  39
  40         flash@0 {
  41                 compatible = "jedec,spi-nor";
  42                 reg = <0>;
  43                 spi-max-frequency = <10000000>;
  44
  45                 partitions {
  46                         compatible = "fixed-partitions";
  47                         #address-cells = <1>;
  48                         #size-cells = <1>;
  49
  50                         partition@0 {
  51                                 label = "u-boot";
  52                                 reg = <0x0 0x30000>;
  53                                 read-only;
  54                         };
  55
  56                         partition@30000 {
  57                                 label = "u-boot-env";
  58                                 reg = <0x30000 0x10000>;
  59                                 read-only;
  60                         };
  61
  62                         factory: partition@40000 {
  63                                 label = "factory";
  64                                 reg = <0x40000 0x10000>;
  65                                 read-only;
  66
  67                                 nvmem-layout {
  68                                         compatible = "fixed-layout";
  69                                         #address-cells = <1>;
  70                                         #size-cells = <1>;
  71
  72                                         macaddr_factory_e000: macaddr@e000 {
  73                                                 reg = <0xe000 0x6>;
  74                                         };
  75
  76                                         macaddr_factory_e006: macaddr@e006 {
  77                                                 reg = <0xe006 0x6>;
  78                                         };
  79                                 };
  80                         };
  81
  82                         partition@50000 {
  83                                 compatible = "denx,uimage";
  84                                 label = "firmware";
  85                                 reg = <0x50000 0x3fb0000>;
  86                         };
  87                 };
  88         };
  89 };
  90
  91 &gmac0 {
  92         nvmem-cells = <&macaddr_factory_e000>;
  93         nvmem-cell-names = "mac-address";
  94 };
  95
  96 &gmac1 {
  97         status = "okay";
  98         label = "wan";
  99         phy-handle = <&ethphy4>;
 100
 101         nvmem-cells = <&macaddr_factory_e006>;
 102         nvmem-cell-names = "mac-address";
 103 };
 104
 105 &mdio {
 106         ethphy4: ethernet-phy@4 {
 107                 reg = <4>;
 108         };
 109 };
 110
 111 &switch0 {
 112         ports {
 113                 port@0 {
 114                         status = "okay";
 115                         label = "lan1";
 116                 };
 117
 118                 port@1 {
 119                         status = "okay";
 120                         label = "lan2";
 121                 };
 122
 123                 port@2 {
 124                         status = "okay";
 125                         label = "lan3";
 126                 };
 127
 128                 port@3 {
 129                         status = "okay";
 130                         label = "lan4";
 131                 };
 132         };
 133 };
 134
 135 &state_default {
 136         gpio {
 137                 groups = "sdhci";
 138                 function = "gpio";
 139         };
 140 };