Runtime tested on Orange Pi R1 Plus LTS and NanoPi R4S.
Removed upstreamed patches:
- 100-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus.patch
- 101-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus-LT.patch
- 103-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch
- 104-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch
Refreshed remaining patches.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/kernel.mk
-PKG_VERSION:=2023.07.02
+PKG_VERSION:=2024.01
PKG_RELEASE:=1
-PKG_HASH:=6b6a48581c14abb0f95bd87c1af4d740922406d7b801002a9f94727fdde021d5
+PKG_HASH:=b99611f1ed237bf3541bdc8434b68c96a6e05967061f992443cb30aabebef5b3
PKG_MAINTAINER:=Tobias Maedel <openwrt@tbspace.de>
+++ /dev/null
-From 89afb631d965292aaf433806d8224b53d9e74036 Mon Sep 17 00:00:00 2001
-From: Tianling Shen <cnsztl@gmail.com>
-Date: Sat, 20 May 2023 18:50:38 +0800
-Subject: [PATCH] rockchip: rk3328: Add support for Orange Pi R1 Plus
-
-Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
-
-This device is similar to the NanoPi R2S, and has a 16MB
-SPI NOR (mx25l12805d). The reset button is changed to
-directly reset the power supply, another detail is that
-both network ports have independent MAC addresses.
-
-The device tree and description are taken from kernel v6.3-rc1.
-
-Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-Signed-off-by: Tianling Shen <cnsztl@gmail.com>
----
- arch/arm/dts/Makefile | 1 +
- .../dts/rk3328-orangepi-r1-plus-u-boot.dtsi | 46 +++
- arch/arm/dts/rk3328-orangepi-r1-plus.dts | 373 ++++++++++++++++++
- board/rockchip/evb_rk3328/MAINTAINERS | 6 +
- configs/orangepi-r1-plus-rk3328_defconfig | 114 ++++++
- 5 files changed, 540 insertions(+)
- create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
- create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus.dts
- create mode 100644 configs/orangepi-r1-plus-rk3328_defconfig
-
---- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -125,6 +125,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3328) += \
- rk3328-evb.dtb \
- rk3328-nanopi-r2c.dtb \
- rk3328-nanopi-r2s.dtb \
-+ rk3328-orangepi-r1-plus.dtb \
- rk3328-roc-cc.dtb \
- rk3328-rock64.dtb \
- rk3328-rock-pi-e.dtb
---- /dev/null
-+++ b/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
-@@ -0,0 +1,46 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later
-+/*
-+ * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd
-+ * (C) Copyright 2020 David Bauer
-+ */
-+
-+#include "rk3328-u-boot.dtsi"
-+#include "rk3328-sdram-ddr4-666.dtsi"
-+/ {
-+ chosen {
-+ u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc;
-+ };
-+};
-+
-+&gpio0 {
-+ bootph-pre-ram;
-+};
-+
-+&pinctrl {
-+ bootph-pre-ram;
-+};
-+
-+&sdmmc0m1_pin {
-+ bootph-pre-ram;
-+};
-+
-+&pcfg_pull_up_4ma {
-+ bootph-pre-ram;
-+};
-+
-+/* Need this and all the pinctrl/gpio stuff above to set pinmux */
-+&vcc_sd {
-+ bootph-pre-ram;
-+};
-+
-+&gmac2io {
-+ snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
-+ snps,reset-active-low;
-+ snps,reset-delays-us = <0 10000 50000>;
-+};
-+
-+&spi0 {
-+ spi_flash: spiflash@0 {
-+ bootph-all;
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/dts/rk3328-orangepi-r1-plus.dts
-@@ -0,0 +1,373 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * Based on rk3328-nanopi-r2s.dts, which is:
-+ * Copyright (c) 2020 David Bauer <mail@david-bauer.net>
-+ */
-+
-+/dts-v1/;
-+
-+#include <dt-bindings/gpio/gpio.h>
-+#include <dt-bindings/leds/common.h>
-+#include "rk3328.dtsi"
-+
-+/ {
-+ model = "Xunlong Orange Pi R1 Plus";
-+ compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328";
-+
-+ aliases {
-+ ethernet1 = &rtl8153;
-+ mmc0 = &sdmmc;
-+ };
-+
-+ chosen {
-+ stdout-path = "serial2:1500000n8";
-+ };
-+
-+ gmac_clk: gmac-clock {
-+ compatible = "fixed-clock";
-+ clock-frequency = <125000000>;
-+ clock-output-names = "gmac_clkin";
-+ #clock-cells = <0>;
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
-+ pinctrl-names = "default";
-+
-+ led-0 {
-+ function = LED_FUNCTION_LAN;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-1 {
-+ function = LED_FUNCTION_STATUS;
-+ color = <LED_COLOR_ID_RED>;
-+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "heartbeat";
-+ };
-+
-+ led-2 {
-+ function = LED_FUNCTION_WAN;
-+ color = <LED_COLOR_ID_GREEN>;
-+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ vcc_sd: sdmmc-regulator {
-+ compatible = "regulator-fixed";
-+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
-+ pinctrl-0 = <&sdmmc0m1_pin>;
-+ pinctrl-names = "default";
-+ regulator-name = "vcc_sd";
-+ regulator-boot-on;
-+ vin-supply = <&vcc_io>;
-+ };
-+
-+ vcc_sys: vcc-sys-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vcc_sys";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ };
-+
-+ vdd_5v_lan: vdd-5v-lan-regulator {
-+ compatible = "regulator-fixed";
-+ enable-active-high;
-+ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
-+ pinctrl-0 = <&lan_vdd_pin>;
-+ pinctrl-names = "default";
-+ regulator-name = "vdd_5v_lan";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ vin-supply = <&vcc_sys>;
-+ };
-+};
-+
-+&cpu0 {
-+ cpu-supply = <&vdd_arm>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&vdd_arm>;
-+};
-+
-+&cpu2 {
-+ cpu-supply = <&vdd_arm>;
-+};
-+
-+&cpu3 {
-+ cpu-supply = <&vdd_arm>;
-+};
-+
-+&display_subsystem {
-+ status = "disabled";
-+};
-+
-+&gmac2io {
-+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
-+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
-+ clock_in_out = "input";
-+ phy-handle = <&rtl8211e>;
-+ phy-mode = "rgmii";
-+ phy-supply = <&vcc_io>;
-+ pinctrl-0 = <&rgmiim1_pins>;
-+ pinctrl-names = "default";
-+ snps,aal;
-+ rx_delay = <0x18>;
-+ tx_delay = <0x24>;
-+ status = "okay";
-+
-+ mdio {
-+ compatible = "snps,dwmac-mdio";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ rtl8211e: ethernet-phy@1 {
-+ reg = <1>;
-+ pinctrl-0 = <ð_phy_reset_pin>;
-+ pinctrl-names = "default";
-+ reset-assert-us = <10000>;
-+ reset-deassert-us = <50000>;
-+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+};
-+
-+&i2c1 {
-+ status = "okay";
-+
-+ rk805: pmic@18 {
-+ compatible = "rockchip,rk805";
-+ reg = <0x18>;
-+ interrupt-parent = <&gpio1>;
-+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
-+ #clock-cells = <1>;
-+ clock-output-names = "xin32k", "rk805-clkout2";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ pinctrl-0 = <&pmic_int_l>;
-+ pinctrl-names = "default";
-+ rockchip,system-power-controller;
-+ wakeup-source;
-+
-+ vcc1-supply = <&vcc_sys>;
-+ vcc2-supply = <&vcc_sys>;
-+ vcc3-supply = <&vcc_sys>;
-+ vcc4-supply = <&vcc_sys>;
-+ vcc5-supply = <&vcc_io>;
-+ vcc6-supply = <&vcc_sys>;
-+
-+ regulators {
-+ vdd_log: DCDC_REG1 {
-+ regulator-name = "vdd_log";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <712500>;
-+ regulator-max-microvolt = <1450000>;
-+ regulator-ramp-delay = <12500>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <1000000>;
-+ };
-+ };
-+
-+ vdd_arm: DCDC_REG2 {
-+ regulator-name = "vdd_arm";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <712500>;
-+ regulator-max-microvolt = <1450000>;
-+ regulator-ramp-delay = <12500>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <950000>;
-+ };
-+ };
-+
-+ vcc_ddr: DCDC_REG3 {
-+ regulator-name = "vcc_ddr";
-+ regulator-always-on;
-+ regulator-boot-on;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ };
-+ };
-+
-+ vcc_io: DCDC_REG4 {
-+ regulator-name = "vcc_io";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <3300000>;
-+ };
-+ };
-+
-+ vcc_18: LDO_REG1 {
-+ regulator-name = "vcc_18";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <1800000>;
-+ };
-+ };
-+
-+ vcc18_emmc: LDO_REG2 {
-+ regulator-name = "vcc18_emmc";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <1800000>;
-+ };
-+ };
-+
-+ vdd_10: LDO_REG3 {
-+ regulator-name = "vdd_10";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1000000>;
-+ regulator-max-microvolt = <1000000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <1000000>;
-+ };
-+ };
-+ };
-+ };
-+};
-+
-+&io_domains {
-+ pmuio-supply = <&vcc_io>;
-+ vccio1-supply = <&vcc_io>;
-+ vccio2-supply = <&vcc18_emmc>;
-+ vccio3-supply = <&vcc_io>;
-+ vccio4-supply = <&vcc_io>;
-+ vccio5-supply = <&vcc_io>;
-+ vccio6-supply = <&vcc_io>;
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ gmac2io {
-+ eth_phy_reset_pin: eth-phy-reset-pin {
-+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
-+ };
-+ };
-+
-+ leds {
-+ lan_led_pin: lan-led-pin {
-+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ sys_led_pin: sys-led-pin {
-+ rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ wan_led_pin: wan-led-pin {
-+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+ };
-+
-+ lan {
-+ lan_vdd_pin: lan-vdd-pin {
-+ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+ };
-+
-+ pmic {
-+ pmic_int_l: pmic-int-l {
-+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+};
-+
-+&pwm2 {
-+ status = "okay";
-+};
-+
-+&sdmmc {
-+ bus-width = <4>;
-+ cap-sd-highspeed;
-+ disable-wp;
-+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
-+ pinctrl-names = "default";
-+ vmmc-supply = <&vcc_sd>;
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ status = "okay";
-+
-+ flash@0 {
-+ compatible = "jedec,spi-nor";
-+ reg = <0>;
-+ spi-max-frequency = <50000000>;
-+ };
-+};
-+
-+&tsadc {
-+ rockchip,hw-tshut-mode = <0>;
-+ rockchip,hw-tshut-polarity = <0>;
-+ status = "okay";
-+};
-+
-+&u2phy {
-+ status = "okay";
-+};
-+
-+&u2phy_host {
-+ status = "okay";
-+};
-+
-+&u2phy_otg {
-+ status = "okay";
-+};
-+
-+&uart2 {
-+ status = "okay";
-+};
-+
-+&usb20_otg {
-+ dr_mode = "host";
-+ status = "okay";
-+};
-+
-+&usbdrd3 {
-+ dr_mode = "host";
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ /* Second port is for USB 3.0 */
-+ rtl8153: device@2 {
-+ compatible = "usbbda,8153";
-+ reg = <2>;
-+ };
-+};
-+
-+&usb_host0_ehci {
-+ status = "okay";
-+};
-+
-+&usb_host0_ohci {
-+ status = "okay";
-+};
---- a/board/rockchip/evb_rk3328/MAINTAINERS
-+++ b/board/rockchip/evb_rk3328/MAINTAINERS
-@@ -18,6 +18,12 @@ F: configs/nanopi-r2s-rk3328_defcon
- F: arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi
- F: arch/arm/dts/rk3328-nanopi-r2s.dts
-
-+ORANGEPI-R1-PLUS-RK3328
-+M: Tianling Shen <cnsztl@gmail.com>
-+S: Maintained
-+F: configs/orangepi-r1-plus-rk3328_defconfig
-+F: arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
-+
- ROC-RK3328-CC
- M: Loic Devulder <ldevulder@suse.com>
- M: Chen-Yu Tsai <wens@csie.org>
---- /dev/null
-+++ b/configs/orangepi-r1-plus-rk3328_defconfig
-@@ -0,0 +1,114 @@
-+CONFIG_ARM=y
-+CONFIG_SKIP_LOWLEVEL_INIT=y
-+CONFIG_COUNTER_FREQUENCY=24000000
-+CONFIG_ARCH_ROCKCHIP=y
-+CONFIG_TEXT_BASE=0x00200000
-+CONFIG_SPL_GPIO=y
-+CONFIG_NR_DRAM_BANKS=1
-+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
-+CONFIG_ENV_OFFSET=0x3F8000
-+CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus"
-+CONFIG_DM_RESET=y
-+CONFIG_ROCKCHIP_RK3328=y
-+CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-+CONFIG_TPL_LIBCOMMON_SUPPORT=y
-+CONFIG_TPL_LIBGENERIC_SUPPORT=y
-+CONFIG_SPL_DRIVERS_MISC=y
-+CONFIG_SPL_STACK_R_ADDR=0x600000
-+CONFIG_SPL_STACK=0x400000
-+CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
-+CONFIG_DEBUG_UART_BASE=0xFF130000
-+CONFIG_DEBUG_UART_CLOCK=24000000
-+CONFIG_SYS_LOAD_ADDR=0x800800
-+CONFIG_DEBUG_UART=y
-+# CONFIG_ANDROID_BOOT_IMAGE is not set
-+CONFIG_FIT=y
-+CONFIG_FIT_VERBOSE=y
-+CONFIG_SPL_LOAD_FIT=y
-+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus.dtb"
-+# CONFIG_DISPLAY_CPUINFO is not set
-+CONFIG_DISPLAY_BOARDINFO_LATE=y
-+CONFIG_MISC_INIT_R=y
-+CONFIG_SPL_MAX_SIZE=0x40000
-+CONFIG_SPL_PAD_TO=0x7f8000
-+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-+CONFIG_SPL_BSS_START_ADDR=0x2000000
-+CONFIG_SPL_BSS_MAX_SIZE=0x2000
-+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-+CONFIG_SPL_STACK_R=y
-+CONFIG_SPL_I2C=y
-+CONFIG_SPL_POWER=y
-+CONFIG_SPL_ATF=y
-+CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-+CONFIG_TPL_SYS_MALLOC_SIMPLE=y
-+CONFIG_CMD_BOOTZ=y
-+CONFIG_CMD_GPT=y
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_USB=y
-+# CONFIG_CMD_SETEXPR is not set
-+CONFIG_CMD_TIME=y
-+CONFIG_SPL_OF_CONTROL=y
-+CONFIG_TPL_OF_CONTROL=y
-+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
-+CONFIG_TPL_OF_PLATDATA=y
-+CONFIG_ENV_IS_IN_MMC=y
-+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-+CONFIG_SYS_MMC_ENV_DEV=1
-+CONFIG_NET_RANDOM_ETHADDR=y
-+CONFIG_TPL_DM=y
-+CONFIG_REGMAP=y
-+CONFIG_SPL_REGMAP=y
-+CONFIG_TPL_REGMAP=y
-+CONFIG_SYSCON=y
-+CONFIG_SPL_SYSCON=y
-+CONFIG_TPL_SYSCON=y
-+CONFIG_CLK=y
-+CONFIG_SPL_CLK=y
-+CONFIG_FASTBOOT_BUF_ADDR=0x800800
-+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
-+CONFIG_ROCKCHIP_GPIO=y
-+CONFIG_SYS_I2C_ROCKCHIP=y
-+CONFIG_MMC_DW=y
-+CONFIG_MMC_DW_ROCKCHIP=y
-+CONFIG_SF_DEFAULT_SPEED=20000000
-+CONFIG_SPI_FLASH_GIGADEVICE=y
-+CONFIG_ETH_DESIGNWARE=y
-+CONFIG_GMAC_ROCKCHIP=y
-+CONFIG_PINCTRL=y
-+CONFIG_SPL_PINCTRL=y
-+CONFIG_DM_PMIC=y
-+CONFIG_PMIC_RK8XX=y
-+CONFIG_SPL_PMIC_RK8XX=y
-+CONFIG_SPL_DM_REGULATOR=y
-+CONFIG_REGULATOR_PWM=y
-+CONFIG_DM_REGULATOR_FIXED=y
-+CONFIG_SPL_DM_REGULATOR_FIXED=y
-+CONFIG_REGULATOR_RK8XX=y
-+CONFIG_PWM_ROCKCHIP=y
-+CONFIG_RAM=y
-+CONFIG_SPL_RAM=y
-+CONFIG_TPL_RAM=y
-+CONFIG_BAUDRATE=1500000
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SYS_NS16550_MEM32=y
-+CONFIG_ROCKCHIP_SPI=y
-+CONFIG_SYSINFO=y
-+CONFIG_SYSRESET=y
-+# CONFIG_TPL_SYSRESET is not set
-+CONFIG_USB=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_DWC3=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_EHCI_GENERIC=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_USB_OHCI_GENERIC=y
-+CONFIG_USB_DWC2=y
-+CONFIG_USB_DWC3=y
-+# CONFIG_USB_DWC3_GADGET is not set
-+CONFIG_USB_GADGET=y
-+CONFIG_USB_GADGET_DWC2_OTG=y
-+CONFIG_SPL_TINY_MEMSET=y
-+CONFIG_TPL_TINY_MEMSET=y
-+CONFIG_ERRNO_STR=y
+++ /dev/null
-From 408fd4570c0f1e6b1fe3722998394651144f2a29 Mon Sep 17 00:00:00 2001
-From: Tianling Shen <cnsztl@gmail.com>
-Date: Sat, 20 May 2023 18:52:14 +0800
-Subject: [PATCH] rockchip: rk3328: Add support for Orange Pi R1 Plus LTS
-
-The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
-the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
-changed from DDR4 to LPDDR3.
-
-The device tree is taken from kernel v6.4-rc1.
-
-Signed-off-by: Tianling Shen <cnsztl@gmail.com>
----
- arch/arm/dts/Makefile | 1 +
- .../rk3328-orangepi-r1-plus-lts-u-boot.dtsi | 46 +++++++
- arch/arm/dts/rk3328-orangepi-r1-plus-lts.dts | 40 ++++++
- board/rockchip/evb_rk3328/MAINTAINERS | 6 +
- configs/orangepi-r1-plus-lts-rk3328_defconfig | 114 ++++++++++++++++++
- 5 files changed, 207 insertions(+)
- create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus-lts-u-boot.dtsi
- create mode 100644 arch/arm/dts/rk3328-orangepi-r1-plus-lts.dts
- create mode 100644 configs/orangepi-r1-plus-lts-rk3328_defconfig
-
---- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -126,6 +126,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3328) += \
- rk3328-nanopi-r2c.dtb \
- rk3328-nanopi-r2s.dtb \
- rk3328-orangepi-r1-plus.dtb \
-+ rk3328-orangepi-r1-plus-lts.dtb \
- rk3328-roc-cc.dtb \
- rk3328-rock64.dtb \
- rk3328-rock-pi-e.dtb
---- /dev/null
-+++ b/arch/arm/dts/rk3328-orangepi-r1-plus-lts-u-boot.dtsi
-@@ -0,0 +1,46 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later
-+/*
-+ * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd
-+ * (C) Copyright 2020 David Bauer
-+ */
-+
-+#include "rk3328-u-boot.dtsi"
-+#include "rk3328-sdram-lpddr3-666.dtsi"
-+/ {
-+ chosen {
-+ u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc;
-+ };
-+};
-+
-+&gpio0 {
-+ bootph-pre-ram;
-+};
-+
-+&pinctrl {
-+ bootph-pre-ram;
-+};
-+
-+&sdmmc0m1_pin {
-+ bootph-pre-ram;
-+};
-+
-+&pcfg_pull_up_4ma {
-+ bootph-pre-ram;
-+};
-+
-+/* Need this and all the pinctrl/gpio stuff above to set pinmux */
-+&vcc_sd {
-+ bootph-pre-ram;
-+};
-+
-+&gmac2io {
-+ snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
-+ snps,reset-active-low;
-+ snps,reset-delays-us = <0 10000 50000>;
-+};
-+
-+&spi0 {
-+ spi_flash: spiflash@0 {
-+ bootph-all;
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/dts/rk3328-orangepi-r1-plus-lts.dts
-@@ -0,0 +1,40 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2016 Xunlong Software. Co., Ltd.
-+ * (http://www.orangepi.org)
-+ *
-+ * Copyright (c) 2021-2023 Tianling Shen <cnsztl@gmail.com>
-+ */
-+
-+/dts-v1/;
-+#include "rk3328-orangepi-r1-plus.dts"
-+
-+/ {
-+ model = "Xunlong Orange Pi R1 Plus LTS";
-+ compatible = "xunlong,orangepi-r1-plus-lts", "rockchip,rk3328";
-+};
-+
-+&gmac2io {
-+ phy-handle = <&yt8531c>;
-+ tx_delay = <0x19>;
-+ rx_delay = <0x05>;
-+
-+ mdio {
-+ /delete-node/ ethernet-phy@1;
-+
-+ yt8531c: ethernet-phy@0 {
-+ compatible = "ethernet-phy-ieee802.3-c22";
-+ reg = <0>;
-+
-+ motorcomm,clk-out-frequency-hz = <125000000>;
-+ motorcomm,keep-pll-enabled;
-+ motorcomm,auto-sleep-disabled;
-+
-+ pinctrl-0 = <ð_phy_reset_pin>;
-+ pinctrl-names = "default";
-+ reset-assert-us = <15000>;
-+ reset-deassert-us = <50000>;
-+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+};
---- a/board/rockchip/evb_rk3328/MAINTAINERS
-+++ b/board/rockchip/evb_rk3328/MAINTAINERS
-@@ -24,6 +24,12 @@ S: Maintained
- F: configs/orangepi-r1-plus-rk3328_defconfig
- F: arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
-
-+ORANGEPI-R1-PLUS-LTS-RK3328
-+M: Tianling Shen <cnsztl@gmail.com>
-+S: Maintained
-+F: configs/orangepi-r1-plus-lts-rk3328_defconfig
-+F: arch/arm/dts/rk3328-orangepi-r1-plus-lts-u-boot.dtsi
-+
- ROC-RK3328-CC
- M: Loic Devulder <ldevulder@suse.com>
- M: Chen-Yu Tsai <wens@csie.org>
---- /dev/null
-+++ b/configs/orangepi-r1-plus-lts-rk3328_defconfig
-@@ -0,0 +1,114 @@
-+CONFIG_ARM=y
-+CONFIG_SKIP_LOWLEVEL_INIT=y
-+CONFIG_COUNTER_FREQUENCY=24000000
-+CONFIG_ARCH_ROCKCHIP=y
-+CONFIG_TEXT_BASE=0x00200000
-+CONFIG_SPL_GPIO=y
-+CONFIG_NR_DRAM_BANKS=1
-+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
-+CONFIG_ENV_OFFSET=0x3F8000
-+CONFIG_DEFAULT_DEVICE_TREE="rk3328-orangepi-r1-plus-lts"
-+CONFIG_DM_RESET=y
-+CONFIG_ROCKCHIP_RK3328=y
-+CONFIG_TPL_ROCKCHIP_COMMON_BOARD=y
-+CONFIG_TPL_LIBCOMMON_SUPPORT=y
-+CONFIG_TPL_LIBGENERIC_SUPPORT=y
-+CONFIG_SPL_DRIVERS_MISC=y
-+CONFIG_SPL_STACK_R_ADDR=0x600000
-+CONFIG_SPL_STACK=0x400000
-+CONFIG_TPL_SYS_MALLOC_F_LEN=0x800
-+CONFIG_DEBUG_UART_BASE=0xFF130000
-+CONFIG_DEBUG_UART_CLOCK=24000000
-+CONFIG_SYS_LOAD_ADDR=0x800800
-+CONFIG_DEBUG_UART=y
-+# CONFIG_ANDROID_BOOT_IMAGE is not set
-+CONFIG_FIT=y
-+CONFIG_FIT_VERBOSE=y
-+CONFIG_SPL_LOAD_FIT=y
-+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb"
-+# CONFIG_DISPLAY_CPUINFO is not set
-+CONFIG_DISPLAY_BOARDINFO_LATE=y
-+CONFIG_MISC_INIT_R=y
-+CONFIG_SPL_MAX_SIZE=0x40000
-+CONFIG_SPL_PAD_TO=0x7f8000
-+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-+CONFIG_SPL_BSS_START_ADDR=0x2000000
-+CONFIG_SPL_BSS_MAX_SIZE=0x2000
-+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-+CONFIG_SPL_STACK_R=y
-+CONFIG_SPL_I2C=y
-+CONFIG_SPL_POWER=y
-+CONFIG_SPL_ATF=y
-+CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
-+CONFIG_TPL_SYS_MALLOC_SIMPLE=y
-+CONFIG_CMD_BOOTZ=y
-+CONFIG_CMD_GPT=y
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_USB=y
-+# CONFIG_CMD_SETEXPR is not set
-+CONFIG_CMD_TIME=y
-+CONFIG_SPL_OF_CONTROL=y
-+CONFIG_TPL_OF_CONTROL=y
-+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
-+CONFIG_TPL_OF_PLATDATA=y
-+CONFIG_ENV_IS_IN_MMC=y
-+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-+CONFIG_SYS_MMC_ENV_DEV=1
-+CONFIG_NET_RANDOM_ETHADDR=y
-+CONFIG_TPL_DM=y
-+CONFIG_REGMAP=y
-+CONFIG_SPL_REGMAP=y
-+CONFIG_TPL_REGMAP=y
-+CONFIG_SYSCON=y
-+CONFIG_SPL_SYSCON=y
-+CONFIG_TPL_SYSCON=y
-+CONFIG_CLK=y
-+CONFIG_SPL_CLK=y
-+CONFIG_FASTBOOT_BUF_ADDR=0x800800
-+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
-+CONFIG_ROCKCHIP_GPIO=y
-+CONFIG_SYS_I2C_ROCKCHIP=y
-+CONFIG_MMC_DW=y
-+CONFIG_MMC_DW_ROCKCHIP=y
-+CONFIG_SF_DEFAULT_SPEED=20000000
-+CONFIG_SPI_FLASH_GIGADEVICE=y
-+CONFIG_ETH_DESIGNWARE=y
-+CONFIG_GMAC_ROCKCHIP=y
-+CONFIG_PINCTRL=y
-+CONFIG_SPL_PINCTRL=y
-+CONFIG_DM_PMIC=y
-+CONFIG_PMIC_RK8XX=y
-+CONFIG_SPL_PMIC_RK8XX=y
-+CONFIG_SPL_DM_REGULATOR=y
-+CONFIG_REGULATOR_PWM=y
-+CONFIG_DM_REGULATOR_FIXED=y
-+CONFIG_SPL_DM_REGULATOR_FIXED=y
-+CONFIG_REGULATOR_RK8XX=y
-+CONFIG_PWM_ROCKCHIP=y
-+CONFIG_RAM=y
-+CONFIG_SPL_RAM=y
-+CONFIG_TPL_RAM=y
-+CONFIG_BAUDRATE=1500000
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SYS_NS16550_MEM32=y
-+CONFIG_ROCKCHIP_SPI=y
-+CONFIG_SYSINFO=y
-+CONFIG_SYSRESET=y
-+# CONFIG_TPL_SYSRESET is not set
-+CONFIG_USB=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_DWC3=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_EHCI_GENERIC=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_USB_OHCI_GENERIC=y
-+CONFIG_USB_DWC2=y
-+CONFIG_USB_DWC3=y
-+# CONFIG_USB_DWC3_GADGET is not set
-+CONFIG_USB_GADGET=y
-+CONFIG_USB_GADGET_DWC2_OTG=y
-+CONFIG_SPL_TINY_MEMSET=y
-+CONFIG_TPL_TINY_MEMSET=y
-+CONFIG_ERRNO_STR=y
+++ /dev/null
-From c84214aab0e4c5b2f619dd89655f27b3ae40e82b Mon Sep 17 00:00:00 2001
-From: Tianling Shen <cnsztl@gmail.com>
-Date: Tue, 30 May 2023 15:00:33 +0800
-Subject: [PATCH] rockchip: rk3568: Add support for FriendlyARM NanoPi R5S
-
-FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
-
-Board Specifications
-- Rockchip RK3568
-- 2 or 4GB LPDDR4X
-- 8GB or 16GB eMMC, SD card slot
-- GbE LAN (Native)
-- 2x 2.5G LAN (PCIe)
-- M.2 Connector
-- HDMI 2.0, MIPI DSI/CSI
-- 2xUSB 3.0 Host
-- USB Type C PD, 5V/9V/12V
-- GPIO: 12-pin 0.5mm FPC connector
-
-The device tree is taken from kernel v6.4-rc1.
-
-Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-Signed-off-by: Tianling Shen <cnsztl@gmail.com>
----
- arch/arm/dts/Makefile | 1 +
- arch/arm/dts/rk3568-nanopi-r5s-u-boot.dtsi | 31 ++
- arch/arm/dts/rk3568-nanopi-r5s.dts | 136 +++++
- arch/arm/dts/rk3568-nanopi-r5s.dtsi | 590 +++++++++++++++++++++
- board/rockchip/evb_rk3568/MAINTAINERS | 8 +
- configs/nanopi-r5s-rk3568_defconfig | 85 +++
- 6 files changed, 851 insertions(+)
- create mode 100644 arch/arm/dts/rk3568-nanopi-r5s-u-boot.dtsi
- create mode 100644 arch/arm/dts/rk3568-nanopi-r5s.dts
- create mode 100644 arch/arm/dts/rk3568-nanopi-r5s.dtsi
- create mode 100644 configs/nanopi-r5s-rk3568_defconfig
-
---- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -171,6 +171,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
- rk3566-anbernic-rgxx3.dtb \
- rk3566-radxa-cm3-io.dtb \
- rk3568-evb.dtb \
-+ rk3568-nanopi-r5s.dtb \
- rk3568-rock-3a.dtb
-
- dtb-$(CONFIG_ROCKCHIP_RK3588) += \
---- /dev/null
-+++ b/arch/arm/dts/rk3568-nanopi-r5s-u-boot.dtsi
-@@ -0,0 +1,31 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd.
-+ * (http://www.friendlyelec.com)
-+ *
-+ * Copyright (c) 2023 Tianling Shen <cnsztl@gmail.com>
-+ */
-+
-+#include "rk356x-u-boot.dtsi"
-+
-+/ {
-+ chosen {
-+ stdout-path = &uart2;
-+ u-boot,spl-boot-order = "same-as-spl", &sdmmc0, &sdhci;
-+ };
-+};
-+
-+&sdhci {
-+ cap-mmc-highspeed;
-+ mmc-ddr-1_8v;
-+ mmc-hs200-1_8v;
-+ mmc-hs400-1_8v;
-+ mmc-hs400-enhanced-strobe;
-+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
-+};
-+
-+&uart2 {
-+ clock-frequency = <24000000>;
-+ bootph-all;
-+ status = "okay";
-+};
---- /dev/null
-+++ b/arch/arm/dts/rk3568-nanopi-r5s.dts
-@@ -0,0 +1,136 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd.
-+ * (http://www.friendlyelec.com)
-+ *
-+ * Copyright (c) 2023 Tianling Shen <cnsztl@gmail.com>
-+ */
-+
-+/dts-v1/;
-+#include "rk3568-nanopi-r5s.dtsi"
-+
-+/ {
-+ model = "FriendlyElec NanoPi R5S";
-+ compatible = "friendlyarm,nanopi-r5s", "rockchip,rk3568";
-+
-+ aliases {
-+ ethernet0 = &gmac0;
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&power_led_pin>, <&wan_led_pin>;
-+
-+ led-lan1 {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_LAN;
-+ function-enumerator = <1>;
-+ gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-lan2 {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_LAN;
-+ function-enumerator = <2>;
-+ gpios = <&gpio3 RK_PD7 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ power_led: led-power {
-+ color = <LED_COLOR_ID_RED>;
-+ function = LED_FUNCTION_POWER;
-+ linux,default-trigger = "heartbeat";
-+ gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-wan {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_WAN;
-+ gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&gmac0 {
-+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
-+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
-+ assigned-clock-rates = <0>, <125000000>;
-+ clock_in_out = "output";
-+ phy-handle = <&rgmii_phy0>;
-+ phy-mode = "rgmii";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&gmac0_miim
-+ &gmac0_tx_bus2
-+ &gmac0_rx_bus2
-+ &gmac0_rgmii_clk
-+ &gmac0_rgmii_bus>;
-+ snps,reset-gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_LOW>;
-+ snps,reset-active-low;
-+ /* Reset time is 15ms, 50ms for rtl8211f */
-+ snps,reset-delays-us = <0 15000 50000>;
-+ tx_delay = <0x3c>;
-+ rx_delay = <0x2f>;
-+ status = "okay";
-+};
-+
-+&mdio0 {
-+ rgmii_phy0: ethernet-phy@1 {
-+ compatible = "ethernet-phy-ieee802.3-c22";
-+ reg = <1>;
-+ pinctrl-0 = <ð_phy0_reset_pin>;
-+ pinctrl-names = "default";
-+ };
-+};
-+
-+&pcie2x1 {
-+ num-lanes = <1>;
-+ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
-+ status = "okay";
-+};
-+
-+&pcie30phy {
-+ data-lanes = <1 2>;
-+ status = "okay";
-+};
-+
-+&pcie3x1 {
-+ num-lanes = <1>;
-+ reset-gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
-+ vpcie3v3-supply = <&vcc3v3_pcie>;
-+ status = "okay";
-+};
-+
-+&pcie3x2 {
-+ num-lanes = <1>;
-+ num-ib-windows = <8>;
-+ num-ob-windows = <8>;
-+ reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
-+ vpcie3v3-supply = <&vcc3v3_pcie>;
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ gmac0 {
-+ eth_phy0_reset_pin: eth-phy0-reset-pin {
-+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ lan1_led_pin: lan1-led-pin {
-+ rockchip,pins = <3 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ lan2_led_pin: lan2-led-pin {
-+ rockchip,pins = <3 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ power_led_pin: power-led-pin {
-+ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ wan_led_pin: wan-led-pin {
-+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/dts/rk3568-nanopi-r5s.dtsi
-@@ -0,0 +1,590 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd.
-+ * (http://www.friendlyelec.com)
-+ *
-+ * Copyright (c) 2023 Tianling Shen <cnsztl@gmail.com>
-+ */
-+
-+/dts-v1/;
-+#include <dt-bindings/gpio/gpio.h>
-+#include <dt-bindings/input/input.h>
-+#include <dt-bindings/leds/common.h>
-+#include <dt-bindings/pinctrl/rockchip.h>
-+#include <dt-bindings/soc/rockchip,vop2.h>
-+#include "rk3568.dtsi"
-+
-+/ {
-+ aliases {
-+ mmc0 = &sdmmc0;
-+ mmc1 = &sdhci;
-+ };
-+
-+ chosen: chosen {
-+ stdout-path = "serial2:1500000n8";
-+ };
-+
-+ hdmi-con {
-+ compatible = "hdmi-connector";
-+ type = "a";
-+
-+ port {
-+ hdmi_con_in: endpoint {
-+ remote-endpoint = <&hdmi_out_con>;
-+ };
-+ };
-+ };
-+
-+ vdd_usbc: vdd-usbc-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vdd_usbc";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ };
-+
-+ vcc3v3_sys: vcc3v3-sys-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vcc3v3_sys";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ vin-supply = <&vdd_usbc>;
-+ };
-+
-+ vcc5v0_sys: vcc5v0-sys-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vcc5v0_sys";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ vin-supply = <&vdd_usbc>;
-+ };
-+
-+ vcc3v3_pcie: vcc3v3-pcie-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vcc3v3_pcie";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ enable-active-high;
-+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
-+ startup-delay-us = <200000>;
-+ vin-supply = <&vcc5v0_sys>;
-+ };
-+
-+ vcc5v0_usb: vcc5v0-usb-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "vcc5v0_usb";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ vin-supply = <&vdd_usbc>;
-+ };
-+
-+ vcc5v0_usb_host: vcc5v0-usb-host-regulator {
-+ compatible = "regulator-fixed";
-+ enable-active-high;
-+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&vcc5v0_usb_host_en>;
-+ regulator-name = "vcc5v0_usb_host";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ vin-supply = <&vcc5v0_usb>;
-+ };
-+
-+ vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
-+ compatible = "regulator-fixed";
-+ enable-active-high;
-+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&vcc5v0_usb_otg_en>;
-+ regulator-name = "vcc5v0_usb_otg";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ vin-supply = <&vcc5v0_usb>;
-+ };
-+
-+ pcie30_avdd0v9: pcie30-avdd0v9-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "pcie30_avdd0v9";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <900000>;
-+ regulator-max-microvolt = <900000>;
-+ vin-supply = <&vcc3v3_sys>;
-+ };
-+
-+ pcie30_avdd1v8: pcie30-avdd1v8-regulator {
-+ compatible = "regulator-fixed";
-+ regulator-name = "pcie30_avdd1v8";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+ vin-supply = <&vcc3v3_sys>;
-+ };
-+};
-+
-+&combphy0 {
-+ status = "okay";
-+};
-+
-+&combphy1 {
-+ status = "okay";
-+};
-+
-+&combphy2 {
-+ status = "okay";
-+};
-+
-+&cpu0 {
-+ cpu-supply = <&vdd_cpu>;
-+};
-+
-+&cpu1 {
-+ cpu-supply = <&vdd_cpu>;
-+};
-+
-+&cpu2 {
-+ cpu-supply = <&vdd_cpu>;
-+};
-+
-+&cpu3 {
-+ cpu-supply = <&vdd_cpu>;
-+};
-+
-+&gpu {
-+ mali-supply = <&vdd_gpu>;
-+ status = "okay";
-+};
-+
-+&hdmi {
-+ avdd-0v9-supply = <&vdda0v9_image>;
-+ avdd-1v8-supply = <&vcca1v8_image>;
-+ status = "okay";
-+};
-+
-+&hdmi_in {
-+ hdmi_in_vp0: endpoint {
-+ remote-endpoint = <&vp0_out_hdmi>;
-+ };
-+};
-+
-+&hdmi_out {
-+ hdmi_out_con: endpoint {
-+ remote-endpoint = <&hdmi_con_in>;
-+ };
-+};
-+
-+&hdmi_sound {
-+ status = "okay";
-+};
-+
-+&i2c0 {
-+ status = "okay";
-+
-+ vdd_cpu: regulator@1c {
-+ compatible = "tcs,tcs4525";
-+ reg = <0x1c>;
-+ fcs,suspend-voltage-selector = <1>;
-+ regulator-name = "vdd_cpu";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <800000>;
-+ regulator-max-microvolt = <1150000>;
-+ regulator-ramp-delay = <2300>;
-+ vin-supply = <&vcc5v0_sys>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ rk809: pmic@20 {
-+ compatible = "rockchip,rk809";
-+ reg = <0x20>;
-+ interrupt-parent = <&gpio0>;
-+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
-+ #clock-cells = <1>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pmic_int>;
-+ rockchip,system-power-controller;
-+ vcc1-supply = <&vcc3v3_sys>;
-+ vcc2-supply = <&vcc3v3_sys>;
-+ vcc3-supply = <&vcc3v3_sys>;
-+ vcc4-supply = <&vcc3v3_sys>;
-+ vcc5-supply = <&vcc3v3_sys>;
-+ vcc6-supply = <&vcc3v3_sys>;
-+ vcc7-supply = <&vcc3v3_sys>;
-+ vcc8-supply = <&vcc3v3_sys>;
-+ vcc9-supply = <&vcc3v3_sys>;
-+ wakeup-source;
-+
-+ regulators {
-+ vdd_logic: DCDC_REG1 {
-+ regulator-name = "vdd_logic";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-init-microvolt = <900000>;
-+ regulator-initial-mode = <0x2>;
-+ regulator-min-microvolt = <500000>;
-+ regulator-max-microvolt = <1350000>;
-+ regulator-ramp-delay = <6001>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vdd_gpu: DCDC_REG2 {
-+ regulator-name = "vdd_gpu";
-+ regulator-always-on;
-+ regulator-init-microvolt = <900000>;
-+ regulator-initial-mode = <0x2>;
-+ regulator-min-microvolt = <500000>;
-+ regulator-max-microvolt = <1350000>;
-+ regulator-ramp-delay = <6001>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcc_ddr: DCDC_REG3 {
-+ regulator-name = "vcc_ddr";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-initial-mode = <0x2>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ };
-+ };
-+
-+ vdd_npu: DCDC_REG4 {
-+ regulator-name = "vdd_npu";
-+ regulator-init-microvolt = <900000>;
-+ regulator-initial-mode = <0x2>;
-+ regulator-min-microvolt = <500000>;
-+ regulator-max-microvolt = <1350000>;
-+ regulator-ramp-delay = <6001>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcc_1v8: DCDC_REG5 {
-+ regulator-name = "vcc_1v8";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vdda0v9_image: LDO_REG1 {
-+ regulator-name = "vdda0v9_image";
-+ regulator-min-microvolt = <950000>;
-+ regulator-max-microvolt = <950000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vdda_0v9: LDO_REG2 {
-+ regulator-name = "vdda_0v9";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <900000>;
-+ regulator-max-microvolt = <900000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vdda0v9_pmu: LDO_REG3 {
-+ regulator-name = "vdda0v9_pmu";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <900000>;
-+ regulator-max-microvolt = <900000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <900000>;
-+ };
-+ };
-+
-+ vccio_acodec: LDO_REG4 {
-+ regulator-name = "vccio_acodec";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vccio_sd: LDO_REG5 {
-+ regulator-name = "vccio_sd";
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <3300000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcc3v3_pmu: LDO_REG6 {
-+ regulator-name = "vcc3v3_pmu";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <3300000>;
-+ };
-+ };
-+
-+ vcca_1v8: LDO_REG7 {
-+ regulator-name = "vcca_1v8";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcca1v8_pmu: LDO_REG8 {
-+ regulator-name = "vcca1v8_pmu";
-+ regulator-always-on;
-+ regulator-boot-on;
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-on-in-suspend;
-+ regulator-suspend-microvolt = <1800000>;
-+ };
-+ };
-+
-+ vcca1v8_image: LDO_REG9 {
-+ regulator-name = "vcca1v8_image";
-+ regulator-min-microvolt = <1800000>;
-+ regulator-max-microvolt = <1800000>;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcc_3v3: SWITCH_REG1 {
-+ regulator-name = "vcc_3v3";
-+ regulator-always-on;
-+ regulator-boot-on;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+
-+ vcc3v3_sd: SWITCH_REG2 {
-+ regulator-name = "vcc3v3_sd";
-+ regulator-always-on;
-+ regulator-boot-on;
-+
-+ regulator-state-mem {
-+ regulator-off-in-suspend;
-+ };
-+ };
-+ };
-+
-+ };
-+};
-+
-+&i2c5 {
-+ status = "okay";
-+
-+ hym8563: rtc@51 {
-+ compatible = "haoyu,hym8563";
-+ reg = <0x51>;
-+ interrupt-parent = <&gpio0>;
-+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
-+ #clock-cells = <0>;
-+ clock-output-names = "rtcic_32kout";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&hym8563_int>;
-+ wakeup-source;
-+ };
-+};
-+
-+&i2s0_8ch {
-+ status = "okay";
-+};
-+
-+&pcie30phy {
-+ data-lanes = <1 2>;
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ hym8563 {
-+ hym8563_int: hym8563-int {
-+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+
-+ pmic {
-+ pmic_int: pmic-int {
-+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+
-+ usb {
-+ vcc5v0_usb_host_en: vcc5v0-usb-host-en {
-+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ vcc5v0_usb_otg_en: vcc5v0-usb-otg-en {
-+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+ };
-+};
-+
-+&pmu_io_domains {
-+ pmuio1-supply = <&vcc3v3_pmu>;
-+ pmuio2-supply = <&vcc3v3_pmu>;
-+ vccio1-supply = <&vccio_acodec>;
-+ vccio3-supply = <&vccio_sd>;
-+ vccio4-supply = <&vcc_1v8>;
-+ vccio5-supply = <&vcc_3v3>;
-+ vccio6-supply = <&vcc_1v8>;
-+ vccio7-supply = <&vcc_3v3>;
-+ status = "okay";
-+};
-+
-+&saradc {
-+ vref-supply = <&vcca_1v8>;
-+ status = "okay";
-+};
-+
-+&sdhci {
-+ bus-width = <8>;
-+ max-frequency = <200000000>;
-+ non-removable;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
-+ status = "okay";
-+};
-+
-+&sdmmc0 {
-+ max-frequency = <150000000>;
-+ no-sdio;
-+ no-mmc;
-+ bus-width = <4>;
-+ cap-mmc-highspeed;
-+ cap-sd-highspeed;
-+ disable-wp;
-+ vmmc-supply = <&vcc3v3_sd>;
-+ vqmmc-supply = <&vccio_sd>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
-+ status = "okay";
-+};
-+
-+&tsadc {
-+ rockchip,hw-tshut-mode = <1>;
-+ rockchip,hw-tshut-polarity = <0>;
-+ status = "okay";
-+};
-+
-+&uart2 {
-+ status = "okay";
-+};
-+
-+&usb_host0_ehci {
-+ status = "okay";
-+};
-+
-+&usb_host0_ohci {
-+ status = "okay";
-+};
-+
-+&usb_host0_xhci {
-+ extcon = <&usb2phy0>;
-+ dr_mode = "host";
-+ status = "okay";
-+};
-+
-+&usb_host1_ehci {
-+ status = "okay";
-+};
-+
-+&usb_host1_ohci {
-+ status = "okay";
-+};
-+
-+&usb_host1_xhci {
-+ status = "okay";
-+};
-+
-+&usb2phy0 {
-+ status = "okay";
-+};
-+
-+&usb2phy0_host {
-+ phy-supply = <&vcc5v0_usb_host>;
-+ status = "okay";
-+};
-+
-+&usb2phy0_otg {
-+ status = "okay";
-+};
-+
-+&usb2phy1 {
-+ status = "okay";
-+};
-+
-+&usb2phy1_host {
-+ phy-supply = <&vcc5v0_usb_otg>;
-+ status = "okay";
-+};
-+
-+&usb2phy1_otg {
-+ status = "okay";
-+};
-+
-+&vop {
-+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
-+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
-+ status = "okay";
-+};
-+
-+&vop_mmu {
-+ status = "okay";
-+};
-+
-+&vp0 {
-+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
-+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
-+ remote-endpoint = <&hdmi_in_vp0>;
-+ };
-+};
---- a/board/rockchip/evb_rk3568/MAINTAINERS
-+++ b/board/rockchip/evb_rk3568/MAINTAINERS
-@@ -7,6 +7,14 @@ F: configs/evb-rk3568_defconfig
- F: arch/arm/dts/rk3568-evb-boot.dtsi
- F: arch/arm/dts/rk3568-evb.dts
-
-+NANOPI-R5S
-+M: Tianling Shen <cnsztl@gmail.com>
-+S: Maintained
-+F: configs/nanopi-r5s-rk3568_defconfig
-+F: arch/arm/dts/rk3568-nanopi-r5s.dts
-+F: arch/arm/dts/rk3568-nanopi-r5s.dtsi
-+F: arch/arm/dts/rk3568-nanopi-r5s-u-boot.dtsi
-+
- RADXA-CM3
- M: Jagan Teki <jagan@amarulasolutions.com>
- S: Maintained
---- /dev/null
-+++ b/configs/nanopi-r5s-rk3568_defconfig
-@@ -0,0 +1,85 @@
-+CONFIG_ARM=y
-+CONFIG_SKIP_LOWLEVEL_INIT=y
-+CONFIG_COUNTER_FREQUENCY=24000000
-+CONFIG_ARCH_ROCKCHIP=y
-+CONFIG_TEXT_BASE=0x00a00000
-+CONFIG_SPL_LIBCOMMON_SUPPORT=y
-+CONFIG_SPL_LIBGENERIC_SUPPORT=y
-+CONFIG_NR_DRAM_BANKS=2
-+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
-+CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5s"
-+CONFIG_ROCKCHIP_RK3568=y
-+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
-+CONFIG_SPL_SERIAL=y
-+CONFIG_SPL_STACK_R_ADDR=0x600000
-+CONFIG_TARGET_EVB_RK3568=y
-+CONFIG_SPL_STACK=0x400000
-+CONFIG_DEBUG_UART_BASE=0xFE660000
-+CONFIG_DEBUG_UART_CLOCK=24000000
-+CONFIG_SYS_LOAD_ADDR=0xc00800
-+CONFIG_DEBUG_UART=y
-+CONFIG_FIT=y
-+CONFIG_FIT_VERBOSE=y
-+CONFIG_SPL_LOAD_FIT=y
-+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5s.dtb"
-+# CONFIG_DISPLAY_CPUINFO is not set
-+CONFIG_DISPLAY_BOARDINFO_LATE=y
-+CONFIG_SPL_MAX_SIZE=0x40000
-+CONFIG_SPL_PAD_TO=0x7f8000
-+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-+CONFIG_SPL_BSS_START_ADDR=0x4000000
-+CONFIG_SPL_BSS_MAX_SIZE=0x4000
-+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-+CONFIG_SPL_STACK_R=y
-+CONFIG_SPL_ATF=y
-+CONFIG_CMD_GPIO=y
-+CONFIG_CMD_GPT=y
-+CONFIG_CMD_I2C=y
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_USB=y
-+CONFIG_CMD_PMIC=y
-+CONFIG_CMD_REGULATOR=y
-+# CONFIG_SPL_DOS_PARTITION is not set
-+CONFIG_SPL_OF_CONTROL=y
-+CONFIG_OF_LIVE=y
-+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
-+CONFIG_SPL_DM_WARN=y
-+CONFIG_SPL_REGMAP=y
-+CONFIG_SPL_SYSCON=y
-+CONFIG_SPL_CLK=y
-+CONFIG_ROCKCHIP_GPIO=y
-+CONFIG_SYS_I2C_ROCKCHIP=y
-+CONFIG_MISC=y
-+CONFIG_SUPPORT_EMMC_RPMB=y
-+CONFIG_MMC_DW=y
-+CONFIG_MMC_DW_ROCKCHIP=y
-+CONFIG_MMC_SDHCI=y
-+CONFIG_MMC_SDHCI_SDMA=y
-+CONFIG_MMC_SDHCI_ROCKCHIP=y
-+CONFIG_ETH_DESIGNWARE=y
-+CONFIG_GMAC_ROCKCHIP=y
-+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
-+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
-+CONFIG_POWER_DOMAIN=y
-+CONFIG_DM_PMIC=y
-+CONFIG_PMIC_RK8XX=y
-+CONFIG_SPL_DM_REGULATOR_FIXED=y
-+CONFIG_REGULATOR_RK8XX=y
-+CONFIG_PWM_ROCKCHIP=y
-+CONFIG_SPL_RAM=y
-+CONFIG_BAUDRATE=1500000
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SYS_NS16550_MEM32=y
-+CONFIG_SYSRESET=y
-+CONFIG_SYSRESET_PSCI=y
-+CONFIG_USB=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_DWC3=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_EHCI_GENERIC=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_USB_OHCI_GENERIC=y
-+CONFIG_USB_DWC3=y
-+CONFIG_ERRNO_STR=y
+++ /dev/null
-From 41538742491c46100f570680c02fbdd0d2b6b880 Mon Sep 17 00:00:00 2001
-From: Tianling Shen <cnsztl@gmail.com>
-Date: Tue, 30 May 2023 15:00:33 +0800
-Subject: [PATCH] rockchip: rk3568: Add support for FriendlyARM NanoPi R5C
-
-FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
-
-Specification:
-- Rockchip RK3568
-- 1/4GB LPDDR4X RAM
-- 8/32GB eMMC
-- SD card slot
-- M.2 Connector
-- 2x USB 3.0 Port
-- 2x 2500 Base-T (PCIe, r8125)
-- HDMI 2.0
-- MIPI DSI/CSI
-- USB Type C 5V
-
-The device tree is taken from kernel v6.4-rc1.
-
-Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-Signed-off-by: Tianling Shen <cnsztl@gmail.com>
----
- arch/arm/dts/Makefile | 1 +
- arch/arm/dts/rk3568-nanopi-r5c-u-boot.dtsi | 3 +
- arch/arm/dts/rk3568-nanopi-r5c.dts | 112 +++++++++++++++++++++
- board/rockchip/evb_rk3568/MAINTAINERS | 7 ++
- configs/nanopi-r5c-rk3568_defconfig | 85 ++++++++++++++++
- 5 files changed, 208 insertions(+)
- create mode 100644 arch/arm/dts/rk3568-nanopi-r5c-u-boot.dtsi
- create mode 100644 arch/arm/dts/rk3568-nanopi-r5c.dts
- create mode 100644 configs/nanopi-r5c-rk3568_defconfig
-
---- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -171,6 +171,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
- rk3566-anbernic-rgxx3.dtb \
- rk3566-radxa-cm3-io.dtb \
- rk3568-evb.dtb \
-+ rk3568-nanopi-r5c.dtb \
- rk3568-nanopi-r5s.dtb \
- rk3568-rock-3a.dtb
-
---- /dev/null
-+++ b/arch/arm/dts/rk3568-nanopi-r5c-u-boot.dtsi
-@@ -0,0 +1,3 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+
-+#include "rk3568-nanopi-r5s-u-boot.dtsi"
---- /dev/null
-+++ b/arch/arm/dts/rk3568-nanopi-r5c.dts
-@@ -0,0 +1,112 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-+/*
-+ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd.
-+ * (http://www.friendlyelec.com)
-+ *
-+ * Copyright (c) 2023 Tianling Shen <cnsztl@gmail.com>
-+ */
-+
-+/dts-v1/;
-+#include "rk3568-nanopi-r5s.dtsi"
-+
-+/ {
-+ model = "FriendlyElec NanoPi R5C";
-+ compatible = "friendlyarm,nanopi-r5c", "rockchip,rk3568";
-+
-+ gpio-keys {
-+ compatible = "gpio-keys";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&reset_button_pin>;
-+
-+ button-reset {
-+ debounce-interval = <50>;
-+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
-+ label = "reset";
-+ linux,code = <KEY_RESTART>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&lan_led_pin>, <&power_led_pin>, <&wan_led_pin>, <&wlan_led_pin>;
-+
-+ led-lan {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_LAN;
-+ gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ power_led: led-power {
-+ color = <LED_COLOR_ID_RED>;
-+ function = LED_FUNCTION_POWER;
-+ linux,default-trigger = "heartbeat";
-+ gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-wan {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_WAN;
-+ gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ led-wlan {
-+ color = <LED_COLOR_ID_GREEN>;
-+ function = LED_FUNCTION_WLAN;
-+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&pcie2x1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pcie20_reset_pin>;
-+ reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
-+ status = "okay";
-+};
-+
-+&pcie3x1 {
-+ num-lanes = <1>;
-+ reset-gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
-+ vpcie3v3-supply = <&vcc3v3_pcie>;
-+ status = "okay";
-+};
-+
-+&pcie3x2 {
-+ num-lanes = <1>;
-+ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
-+ vpcie3v3-supply = <&vcc3v3_pcie>;
-+ status = "okay";
-+};
-+
-+&pinctrl {
-+ gpio-leds {
-+ lan_led_pin: lan-led-pin {
-+ rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ power_led_pin: power-led-pin {
-+ rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ wan_led_pin: wan-led-pin {
-+ rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+
-+ wlan_led_pin: wlan-led-pin {
-+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
-+ };
-+ };
-+
-+ pcie {
-+ pcie20_reset_pin: pcie20-reset-pin {
-+ rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+
-+ rockchip-key {
-+ reset_button_pin: reset-button-pin {
-+ rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
-+ };
-+ };
-+};
---- a/board/rockchip/evb_rk3568/MAINTAINERS
-+++ b/board/rockchip/evb_rk3568/MAINTAINERS
-@@ -7,6 +7,13 @@ F: configs/evb-rk3568_defconfig
- F: arch/arm/dts/rk3568-evb-boot.dtsi
- F: arch/arm/dts/rk3568-evb.dts
-
-+NANOPI-R5C
-+M: Tianling Shen <cnsztl@gmail.com>
-+S: Maintained
-+F: configs/nanopi-r5c-rk3568_defconfig
-+F: arch/arm/dts/rk3568-nanopi-r5c.dts
-+F: arch/arm/dts/rk3568-nanopi-r5c-u-boot.dtsi
-+
- NANOPI-R5S
- M: Tianling Shen <cnsztl@gmail.com>
- S: Maintained
---- /dev/null
-+++ b/configs/nanopi-r5c-rk3568_defconfig
-@@ -0,0 +1,85 @@
-+CONFIG_ARM=y
-+CONFIG_SKIP_LOWLEVEL_INIT=y
-+CONFIG_COUNTER_FREQUENCY=24000000
-+CONFIG_ARCH_ROCKCHIP=y
-+CONFIG_TEXT_BASE=0x00a00000
-+CONFIG_SPL_LIBCOMMON_SUPPORT=y
-+CONFIG_SPL_LIBGENERIC_SUPPORT=y
-+CONFIG_NR_DRAM_BANKS=2
-+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
-+CONFIG_DEFAULT_DEVICE_TREE="rk3568-nanopi-r5c"
-+CONFIG_ROCKCHIP_RK3568=y
-+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
-+CONFIG_SPL_SERIAL=y
-+CONFIG_SPL_STACK_R_ADDR=0x600000
-+CONFIG_TARGET_EVB_RK3568=y
-+CONFIG_SPL_STACK=0x400000
-+CONFIG_DEBUG_UART_BASE=0xFE660000
-+CONFIG_DEBUG_UART_CLOCK=24000000
-+CONFIG_SYS_LOAD_ADDR=0xc00800
-+CONFIG_DEBUG_UART=y
-+CONFIG_FIT=y
-+CONFIG_FIT_VERBOSE=y
-+CONFIG_SPL_LOAD_FIT=y
-+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-nanopi-r5c.dtb"
-+# CONFIG_DISPLAY_CPUINFO is not set
-+CONFIG_DISPLAY_BOARDINFO_LATE=y
-+CONFIG_SPL_MAX_SIZE=0x40000
-+CONFIG_SPL_PAD_TO=0x7f8000
-+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-+CONFIG_SPL_BSS_START_ADDR=0x4000000
-+CONFIG_SPL_BSS_MAX_SIZE=0x4000
-+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
-+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-+CONFIG_SPL_STACK_R=y
-+CONFIG_SPL_ATF=y
-+CONFIG_CMD_GPIO=y
-+CONFIG_CMD_GPT=y
-+CONFIG_CMD_I2C=y
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_USB=y
-+CONFIG_CMD_PMIC=y
-+CONFIG_CMD_REGULATOR=y
-+# CONFIG_SPL_DOS_PARTITION is not set
-+CONFIG_SPL_OF_CONTROL=y
-+CONFIG_OF_LIVE=y
-+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
-+CONFIG_SPL_DM_WARN=y
-+CONFIG_SPL_REGMAP=y
-+CONFIG_SPL_SYSCON=y
-+CONFIG_SPL_CLK=y
-+CONFIG_ROCKCHIP_GPIO=y
-+CONFIG_SYS_I2C_ROCKCHIP=y
-+CONFIG_MISC=y
-+CONFIG_SUPPORT_EMMC_RPMB=y
-+CONFIG_MMC_DW=y
-+CONFIG_MMC_DW_ROCKCHIP=y
-+CONFIG_MMC_SDHCI=y
-+CONFIG_MMC_SDHCI_SDMA=y
-+CONFIG_MMC_SDHCI_ROCKCHIP=y
-+CONFIG_ETH_DESIGNWARE=y
-+CONFIG_GMAC_ROCKCHIP=y
-+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
-+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
-+CONFIG_POWER_DOMAIN=y
-+CONFIG_DM_PMIC=y
-+CONFIG_PMIC_RK8XX=y
-+CONFIG_SPL_DM_REGULATOR_FIXED=y
-+CONFIG_REGULATOR_RK8XX=y
-+CONFIG_PWM_ROCKCHIP=y
-+CONFIG_SPL_RAM=y
-+CONFIG_BAUDRATE=1500000
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SYS_NS16550_MEM32=y
-+CONFIG_SYSRESET=y
-+CONFIG_SYSRESET_PSCI=y
-+CONFIG_USB=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_DWC3=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_EHCI_GENERIC=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_USB_OHCI_GENERIC=y
-+CONFIG_USB_DWC3=y
-+CONFIG_ERRNO_STR=y
arch/arm/dts/rk3399-nanopc-t4-u-boot.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
-diff --git a/arch/arm/dts/rk3399-nanopc-t4-u-boot.dtsi b/arch/arm/dts/rk3399-nanopc-t4-u-boot.dtsi
-index 17201bcf41..8b6c9059ab 100644
--- a/arch/arm/dts/rk3399-nanopc-t4-u-boot.dtsi
+++ b/arch/arm/dts/rk3399-nanopc-t4-u-boot.dtsi
@@ -4,4 +4,4 @@
projects / openwrt / staging / mans0n.git / commitdiff