+From 3265f421887847db9ae2c01a00645e33608556d8 Mon Sep 17 00:00:00 2001
+From: Robert Hancock <robert.hancock@calian.com>
+Date: Tue, 25 Jan 2022 10:54:09 -0600
+Subject: [PATCH] net: phy: at803x: add fiber support
+
+Previously this driver always forced the copper page to be selected,
+however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
+needs to be selected. Set the appropriate mode based on the hardware
+mode_cfg strap selection.
+
+Enable the appropriate interrupt bits to detect fiber-side link up
+or down events.
+
+Update config_aneg and read_status methods to use the appropriate
+Clause 37 calls when fiber mode is in use.
+
+Signed-off-by: Robert Hancock <robert.hancock@calian.com>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/phy/at803x.c | 76 +++++++++++++++++++++++++++++++++++-----
+ 1 file changed, 67 insertions(+), 9 deletions(-)
+
+--- a/drivers/net/phy/at803x.c
++++ b/drivers/net/phy/at803x.c
+@@ -48,6 +48,8 @@
+ #define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
+ #define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
+ #define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
++#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
++#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
+ #define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
+ #define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
+ #define AT803X_INTR_ENABLE_WOL BIT(0)
+@@ -82,6 +84,17 @@
+
+ #define AT803X_MODE_CFG_MASK 0x0F
+ #define AT803X_MODE_CFG_SGMII 0x01
++#define AT803X_MODE_CFG_BASET_RGMII 0x00
++#define AT803X_MODE_CFG_BASET_SGMII 0x01
++#define AT803X_MODE_CFG_BX1000_RGMII_50OHM 0x02
++#define AT803X_MODE_CFG_BX1000_RGMII_75OHM 0x03
++#define AT803X_MODE_CFG_BX1000_CONV_50OHM 0x04
++#define AT803X_MODE_CFG_BX1000_CONV_75OHM 0x05
++#define AT803X_MODE_CFG_FX100_RGMII_50OHM 0x06
++#define AT803X_MODE_CFG_FX100_CONV_50OHM 0x07
++#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B
++#define AT803X_MODE_CFG_FX100_RGMII_75OHM 0x0E
++#define AT803X_MODE_CFG_FX100_CONV_75OHM 0x0F
+
+ #define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
+ #define AT803X_PSSR_MR_AN_COMPLETE 0x0200
+@@ -189,6 +202,8 @@ struct at803x_priv {
+ #define AT803X_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */
+ u16 clk_25m_reg;
+ u16 clk_25m_mask;
++ bool is_fiber;
++ bool is_1000basex;
+ struct regulator_dev *vddio_rdev;
+ struct regulator_dev *vddh_rdev;
+ struct regulator *vddio;
+@@ -651,7 +666,33 @@ static int at803x_probe(struct phy_devic
+ return ret;
+ }
+
++ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
++ int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
++ int mode_cfg;
++
++ if (ccr < 0)
++ goto err;
++ mode_cfg = ccr & AT803X_MODE_CFG_MASK;
++
++ switch (mode_cfg) {
++ case AT803X_MODE_CFG_BX1000_RGMII_50OHM:
++ case AT803X_MODE_CFG_BX1000_RGMII_75OHM:
++ priv->is_1000basex = true;
++ fallthrough;
++ case AT803X_MODE_CFG_FX100_RGMII_50OHM:
++ case AT803X_MODE_CFG_FX100_RGMII_75OHM:
++ priv->is_fiber = true;
++ break;
++ }
++ }
++
+ return 0;
++
++err:
++ if (priv->vddio)
++ regulator_disable(priv->vddio);
++
++ return ret;
+ }
+
+ static void at803x_remove(struct phy_device *phydev)
+@@ -664,6 +705,7 @@ static void at803x_remove(struct phy_dev
+
+ static int at803x_get_features(struct phy_device *phydev)
+ {
++ struct at803x_priv *priv = phydev->priv;
+ int err;
+
+ err = genphy_read_abilities(phydev);
+@@ -681,12 +723,13 @@ static int at803x_get_features(struct ph
+ * As a result of that, ESTATUS_1000_XFULL is set
+ * to 1 even when operating in copper TP mode.
+ *
+- * Remove this mode from the supported link modes,
+- * as this driver currently only supports copper
+- * operation.
++ * Remove this mode from the supported link modes
++ * when not operating in 1000BaseX mode.
+ */
+- linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+- phydev->supported);
++ if (!priv->is_1000basex)
++ linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
++ phydev->supported);
++
+ return 0;
+ }
+
+@@ -725,15 +768,18 @@ static int at8031_pll_config(struct phy_
+
+ static int at803x_config_init(struct phy_device *phydev)
+ {
++ struct at803x_priv *priv = phydev->priv;
+ int ret;
+
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ /* Some bootloaders leave the fiber page selected.
+- * Switch to the copper page, as otherwise we read
+- * the PHY capabilities from the fiber side.
++ * Switch to the appropriate page (fiber or copper), as otherwise we
++ * read the PHY capabilities from the wrong page.
+ */
+ phy_lock_mdio_bus(phydev);
+- ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
++ ret = at803x_write_page(phydev,
++ priv->is_fiber ? AT803X_PAGE_FIBER :
++ AT803X_PAGE_COPPER);
+ phy_unlock_mdio_bus(phydev);
+ if (ret)
+ return ret;
+@@ -782,6 +828,7 @@ static int at803x_ack_interrupt(struct p
+
+ static int at803x_config_intr(struct phy_device *phydev)
+ {
++ struct at803x_priv *priv = phydev->priv;
+ int err;
+ int value;
+
+@@ -793,6 +840,10 @@ static int at803x_config_intr(struct phy
+ value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
+ value |= AT803X_INTR_ENABLE_LINK_FAIL;
+ value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
++ if (priv->is_fiber) {
++ value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
++ value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
++ }
+
+ err = phy_write(phydev, AT803X_INTR_ENABLE, value);
+ }
+@@ -859,8 +910,12 @@ static int at803x_aneg_done(struct phy_d
+
+ static int at803x_read_status(struct phy_device *phydev)
+ {
++ struct at803x_priv *priv = phydev->priv;
+ int ss, err, old_link = phydev->link;
+
++ if (priv->is_1000basex)
++ return genphy_c37_read_status(phydev);
++
+ /* Update the link, but return if there was an error */
+ err = genphy_update_link(phydev);
+ if (err)
+@@ -959,6 +1014,7 @@ static int at803x_config_mdix(struct phy
+
+ static int at803x_config_aneg(struct phy_device *phydev)
+ {
++ struct at803x_priv *priv = phydev->priv;
+ int ret;
+
+ ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
+@@ -975,6 +1031,9 @@ static int at803x_config_aneg(struct phy
+ return ret;
+ }
+
++ if (priv->is_1000basex)
++ return genphy_c37_config_aneg(phydev);
++
+ return genphy_config_aneg(phydev);
+ }
+