From: Luis Mita Date: Wed, 22 Nov 2023 19:13:04 +0000 (-0400) Subject: mediatek: add support for Confiabits MT7981 X-Git-Url: http://git.openwrt.org/source?a=commitdiff_plain;h=2af07eb85393689a74d32d6211663a0e5ec02a01;p=openwrt%2Fstaging%2Fhauke.git mediatek: add support for Confiabits MT7981 Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981. Specification: - SoC: MediaTek MT7981B - CPU: 2x 1.3 GHz Cortex-A53 - Flash: 128 MiB SPI NAND - RAM: 256 MiB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax) - Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN) - USB 2.0 port - Buttons: 1 Reset button, 1 Mesh button. - LEDs: 7x light-blue, 2x warm-white - Serial console: internal 4-pin header, 115200 8n1 - Power: 12 VDC, 1.5 A MAC addresses in stock firmware and in this commit: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 00:0c:43:xx:xx:e1 | label+1 | | LAN | 00:0c:43:xx:xx:e0 | label | | WLAN 2g | 00:0c:43:xx:xx:e0 | label | | WLAN 5g | 02:0c:43:xx:xx:e0 | | +---------+-------------------+-----------+ The label MAC was found in 'Factory', 0x4 Installation: The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image with the 'Keep settings' option turned off. Signed-off-by: Luis Mita --- diff --git a/target/linux/mediatek/dts/mt7981b-confiabits-mt7981.dts b/target/linux/mediatek/dts/mt7981b-confiabits-mt7981.dts new file mode 100644 index 0000000000..2824bbfc84 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-confiabits-mt7981.dts @@ -0,0 +1,296 @@ +/dts-v1/; + +#include "mt7981.dtsi" +#include +#include +#include + +/ { + model = "Confiabits MT7981"; + compatible = "confiabits,mt7981", "mediatek,mt7981"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-mesh { + label = "mesh"; + linux,input-type = ; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + debounce-interval = <60>; + }; + + button-reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-wlan5g { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <5>; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led-wan-red { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + }; + + led_power: led-power { + label = "blue:power"; // can be removed once #13837 is merged + color = ; + function = LED_FUNCTION_POWER; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + led-lan1 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led-lan2 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led-lan3 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led-wan-blue { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + led-wlan2g { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <2>; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-mesh { + color = ; + function = "mesh"; // no LED_FUNCTION_MESH yet + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 0>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + + +&mdio_bus { + #address-cells = <1>; + #size-cells = <0>; + + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 1>; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x4000000>; + compatible = "linux,ubi"; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + +}; + +&usb_phy { + status = "okay"; +}; + +&xhci { + status = "okay"; + mediatek,u3p-dis-msk = <0x1>; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 84a8cfbc0b..b1411d56d3 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -6,6 +6,12 @@ board=$(board_name) board_config_update case $board in +confiabits,mt7981) + ucidef_set_led_netdev "lan1" "lan1" "blue:lan-1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan2" "lan2" "blue:lan-2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan3" "lan3" "blue:lan-3" "lan3" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" + ;; cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 0675e87853..275a322a65 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -23,6 +23,7 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ;; cetron,ct3003|\ + confiabits,mt7981|\ cudy,wr3000-v1|\ jcg,q30-pro|\ qihoo,360t7) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 7c452ecb1e..195fcb5d2c 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -255,6 +255,22 @@ define Device/cmcc_rax3000m endef TARGET_DEVICES += cmcc_rax3000m +define Device/confiabits_mt7981 + DEVICE_VENDOR := Confiabits + DEVICE_MODEL := MT7981 + DEVICE_DTS := mt7981b-confiabits-mt7981 + DEVICE_DTS_DIR := ../dts + SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-2500wan-gmac2-rfb + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-usb3 kmod-mt7981-firmware +endef +TARGET_DEVICES += confiabits_mt7981 + define Device/cudy_wr3000-v1 DEVICE_VENDOR := Cudy DEVICE_MODEL := WR3000