env/Kconfig

   1 menu "Environment"
   2
   3 config ENV_IS_NOWHERE
   4         bool "Environment is not stored"
   5         default y if !ENV_IS_IN_EEPROM && !ENV_IS_IN_EXT4 && \
   6                      !ENV_IS_IN_FAT && !ENV_IS_IN_FLASH && \
   7                      !ENV_IS_IN_MMC && !ENV_IS_IN_NAND && \
   8                      !ENV_IS_IN_NVRAM && !ENV_IS_IN_ONENAND && \
   9                      !ENV_IS_IN_REMOTE && !ENV_IS_IN_SPI_FLASH && \
  10                      !ENV_IS_IN_UBI
  11         help
  12           Define this if you don't want to or can't have an environment stored
  13           on a storage medium. In this case the environment will still exist
  14           while U-Boot is running, but once U-Boot exits it will not be
  15           stored. U-Boot will therefore always start up with a default
  16           environment.
  17
  18 config ENV_IS_IN_EEPROM
  19         bool "Environment in EEPROM"
  20         depends on !CHAIN_OF_TRUST
  21         help
  22           Use this if you have an EEPROM or similar serial access
  23           device and a driver for it.
  24
  25           - CONFIG_ENV_OFFSET:
  26           - CONFIG_ENV_SIZE:
  27
  28           These two #defines specify the offset and size of the
  29           environment area within the total memory of your EEPROM.
  30
  31           Note that we consider the length of the address field to
  32           still be one byte because the extra address bits are hidden
  33           in the chip address.
  34
  35           - CONFIG_ENV_EEPROM_IS_ON_I2C
  36           define this, if you have I2C and SPI activated, and your
  37           EEPROM, which holds the environment, is on the I2C bus.
  38
  39           - CONFIG_I2C_ENV_EEPROM_BUS
  40           if you have an Environment on an EEPROM reached over
  41           I2C muxes, you can define here, how to reach this
  42           EEPROM. For example:
  43
  44           #define CONFIG_I2C_ENV_EEPROM_BUS       1
  45
  46           EEPROM which holds the environment, is reached over
  47           a pca9547 i2c mux with address 0x70, channel 3.
  48
  49 config ENV_IS_IN_FAT
  50         bool "Environment is in a FAT filesystem"
  51         depends on !CHAIN_OF_TRUST
  52         default y if ARCH_BCM283X
  53         default y if ARCH_SUNXI && MMC
  54         default y if MMC_OMAP_HS && TI_COMMON_CMD_OPTIONS
  55         select FS_FAT
  56         select FAT_WRITE
  57         help
  58           Define this if you want to use the FAT file system for the environment.
  59
  60 config ENV_IS_IN_EXT4
  61         bool "Environment is in a EXT4 filesystem"
  62         depends on !CHAIN_OF_TRUST
  63         select EXT4_WRITE
  64         help
  65           Define this if you want to use the EXT4 file system for the environment.
  66
  67 config ENV_IS_IN_FLASH
  68         bool "Environment in flash memory"
  69         depends on !CHAIN_OF_TRUST
  70         default y if ARCH_CINTEGRATOR
  71         default y if ARCH_INTEGRATOR_CP
  72         default y if M548x || M547x || M5282 || MCF547x_8x
  73         default y if MCF532x || MCF52x2
  74         default y if MPC86xx || MPC83xx
  75         default y if ARCH_MPC8572 || ARCH_MPC8548 || ARCH_MPC8641
  76         default y if SH && !CPU_SH4
  77         help
  78           Define this if you have a flash device which you want to use for the
  79           environment.
  80
  81           a) The environment occupies one whole flash sector, which is
  82            "embedded" in the text segment with the U-Boot code. This
  83            happens usually with "bottom boot sector" or "top boot
  84            sector" type flash chips, which have several smaller
  85            sectors at the start or the end. For instance, such a
  86            layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
  87            such a case you would place the environment in one of the
  88            4 kB sectors - with U-Boot code before and after it. With
  89            "top boot sector" type flash chips, you would put the
  90            environment in one of the last sectors, leaving a gap
  91            between U-Boot and the environment.
  92
  93           CONFIG_ENV_OFFSET:
  94
  95            Offset of environment data (variable area) to the
  96            beginning of flash memory; for instance, with bottom boot
  97            type flash chips the second sector can be used: the offset
  98            for this sector is given here.
  99
 100            CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
 101
 102           CONFIG_ENV_ADDR:
 103
 104            This is just another way to specify the start address of
 105            the flash sector containing the environment (instead of
 106            CONFIG_ENV_OFFSET).
 107
 108           CONFIG_ENV_SECT_SIZE:
 109
 110            Size of the sector containing the environment.
 111
 112
 113           b) Sometimes flash chips have few, equal sized, BIG sectors.
 114            In such a case you don't want to spend a whole sector for
 115            the environment.
 116
 117           CONFIG_ENV_SIZE:
 118
 119            If you use this in combination with CONFIG_ENV_IS_IN_FLASH
 120            and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
 121            of this flash sector for the environment. This saves
 122            memory for the RAM copy of the environment.
 123
 124            It may also save flash memory if you decide to use this
 125            when your environment is "embedded" within U-Boot code,
 126            since then the remainder of the flash sector could be used
 127            for U-Boot code. It should be pointed out that this is
 128            STRONGLY DISCOURAGED from a robustness point of view:
 129            updating the environment in flash makes it always
 130            necessary to erase the WHOLE sector. If something goes
 131            wrong before the contents has been restored from a copy in
 132            RAM, your target system will be dead.
 133
 134           CONFIG_ENV_ADDR_REDUND
 135           CONFIG_ENV_SIZE_REDUND
 136
 137            These settings describe a second storage area used to hold
 138            a redundant copy of the environment data, so that there is
 139            a valid backup copy in case there is a power failure during
 140            a "saveenv" operation.
 141
 142           BE CAREFUL! Any changes to the flash layout, and some changes to the
 143           source code will make it necessary to adapt <board>/u-boot.lds*
 144           accordingly!
 145
 146 config ENV_IS_IN_MMC
 147         bool "Environment in an MMC device"
 148         depends on !CHAIN_OF_TRUST
 149         depends on MMC
 150         default y if ARCH_EXYNOS4
 151         default y if MX6SX || MX7D
 152         default y if TEGRA30 || TEGRA124
 153         default y if TEGRA_ARMV8_COMMON
 154         help
 155           Define this if you have an MMC device which you want to use for the
 156           environment.
 157
 158           CONFIG_SYS_MMC_ENV_DEV:
 159
 160           Specifies which MMC device the environment is stored in.
 161
 162           CONFIG_SYS_MMC_ENV_PART (optional):
 163
 164           Specifies which MMC partition the environment is stored in. If not
 165           set, defaults to partition 0, the user area. Common values might be
 166           1 (first MMC boot partition), 2 (second MMC boot partition).
 167
 168           CONFIG_ENV_OFFSET:
 169           CONFIG_ENV_SIZE:
 170
 171           These two #defines specify the offset and size of the environment
 172           area within the specified MMC device.
 173
 174           If offset is positive (the usual case), it is treated as relative to
 175           the start of the MMC partition. If offset is negative, it is treated
 176           as relative to the end of the MMC partition. This can be useful if
 177           your board may be fitted with different MMC devices, which have
 178           different sizes for the MMC partitions, and you always want the
 179           environment placed at the very end of the partition, to leave the
 180           maximum possible space before it, to store other data.
 181
 182           These two values are in units of bytes, but must be aligned to an
 183           MMC sector boundary.
 184
 185           CONFIG_ENV_OFFSET_REDUND (optional):
 186
 187           Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
 188           hold a redundant copy of the environment data. This provides a
 189           valid backup copy in case the other copy is corrupted, e.g. due
 190           to a power failure during a "saveenv" operation.
 191
 192           This value may also be positive or negative; this is handled in the
 193           same way as CONFIG_ENV_OFFSET.
 194
 195           This value is also in units of bytes, but must also be aligned to
 196           an MMC sector boundary.
 197
 198           CONFIG_ENV_SIZE_REDUND (optional):
 199
 200           This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
 201           set. If this value is set, it must be set to the same value as
 202           CONFIG_ENV_SIZE.
 203
 204 config ENV_IS_IN_NAND
 205         bool "Environment in a NAND device"
 206         depends on !CHAIN_OF_TRUST
 207         help
 208           Define this if you have a NAND device which you want to use for the
 209           environment.
 210
 211           - CONFIG_ENV_OFFSET:
 212           - CONFIG_ENV_SIZE:
 213
 214           These two #defines specify the offset and size of the environment
 215           area within the first NAND device.  CONFIG_ENV_OFFSET must be
 216           aligned to an erase block boundary.
 217
 218           - CONFIG_ENV_OFFSET_REDUND (optional):
 219
 220           This setting describes a second storage area of CONFIG_ENV_SIZE
 221           size used to hold a redundant copy of the environment data, so
 222           that there is a valid backup copy in case there is a power failure
 223           during a "saveenv" operation.  CONFIG_ENV_OFFSET_REDUND must be
 224           aligned to an erase block boundary.
 225
 226           - CONFIG_ENV_RANGE (optional):
 227
 228           Specifies the length of the region in which the environment
 229           can be written.  This should be a multiple of the NAND device's
 230           block size.  Specifying a range with more erase blocks than
 231           are needed to hold CONFIG_ENV_SIZE allows bad blocks within
 232           the range to be avoided.
 233
 234           - CONFIG_ENV_OFFSET_OOB (optional):
 235
 236           Enables support for dynamically retrieving the offset of the
 237           environment from block zero's out-of-band data.  The
 238           "nand env.oob" command can be used to record this offset.
 239           Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
 240           using CONFIG_ENV_OFFSET_OOB.
 241
 242 config ENV_IS_IN_NVRAM
 243         bool "Environment in a non-volatile RAM"
 244         depends on !CHAIN_OF_TRUST
 245         help
 246           Define this if you have some non-volatile memory device
 247           (NVRAM, battery buffered SRAM) which you want to use for the
 248           environment.
 249
 250           - CONFIG_ENV_ADDR:
 251           - CONFIG_ENV_SIZE:
 252
 253           These two #defines are used to determine the memory area you
 254           want to use for environment. It is assumed that this memory
 255           can just be read and written to, without any special
 256           provision.
 257
 258 config ENV_IS_IN_ONENAND
 259         bool "Environment is in OneNAND"
 260         depends on !CHAIN_OF_TRUST
 261         help
 262           Define this if you want to put your local device's environment in
 263           OneNAND.
 264
 265           - CONFIG_ENV_ADDR:
 266           - CONFIG_ENV_SIZE:
 267
 268           These two #defines are used to determine the device range you
 269           want to use for environment. It is assumed that this memory
 270           can just be read and written to, without any special
 271           provision.
 272
 273 config ENV_IS_IN_REMOTE
 274         bool "Environment is in remote memory space"
 275         depends on !CHAIN_OF_TRUST
 276         help
 277           Define this if you have a remote memory space which you
 278           want to use for the local device's environment.
 279
 280           - CONFIG_ENV_ADDR:
 281           - CONFIG_ENV_SIZE:
 282
 283           These two #defines specify the address and size of the
 284           environment area within the remote memory space. The
 285           local device can get the environment from remote memory
 286           space by SRIO or PCIE links.
 287
 288 config ENV_IS_IN_SPI_FLASH
 289         bool "Environment is in SPI flash"
 290         depends on !CHAIN_OF_TRUST && SPI
 291         default y if ARMADA_XP
 292         default y if INTEL_BAYTRAIL
 293         default y if INTEL_BRASWELL
 294         default y if INTEL_BROADWELL
 295         default y if NORTHBRIDGE_INTEL_IVYBRIDGE
 296         default y if INTEL_QUARK
 297         default y if INTEL_QUEENSBAY
 298         help
 299           Define this if you have a SPI Flash memory device which you
 300           want to use for the environment.
 301
 302           - CONFIG_ENV_OFFSET:
 303           - CONFIG_ENV_SIZE:
 304
 305           These two #defines specify the offset and size of the
 306           environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
 307           aligned to an erase sector boundary.
 308
 309           - CONFIG_ENV_SECT_SIZE:
 310
 311           Define the SPI flash's sector size.
 312
 313           - CONFIG_ENV_OFFSET_REDUND (optional):
 314
 315           This setting describes a second storage area of CONFIG_ENV_SIZE
 316           size used to hold a redundant copy of the environment data, so
 317           that there is a valid backup copy in case there is a power failure
 318           during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
 319           aligned to an erase sector boundary.
 320
 321 config USE_ENV_SPI_BUS
 322         bool "SPI flash bus for environment"
 323         depends on ENV_IS_IN_SPI_FLASH
 324         help
 325           Force the SPI bus for environment.
 326           If not defined, use CONFIG_SF_DEFAULT_BUS.
 327
 328 config ENV_SPI_BUS
 329         int "Value of SPI flash bus for environment"
 330         depends on USE_ENV_SPI_BUS
 331         help
 332           Value the SPI bus and chip select for environment.
 333
 334 config USE_ENV_SPI_CS
 335         bool "SPI flash chip select for environment"
 336         depends on ENV_IS_IN_SPI_FLASH
 337         help
 338           Force the SPI chip select for environment.
 339           If not defined, use CONFIG_SF_DEFAULT_CS.
 340
 341 config ENV_SPI_CS
 342         int "Value of SPI flash chip select for environment"
 343         depends on USE_ENV_SPI_CS
 344         help
 345           Value of the SPI chip select for environment.
 346
 347 config USE_ENV_SPI_MAX_HZ
 348         bool "SPI flash max frequency for environment"
 349         depends on ENV_IS_IN_SPI_FLASH
 350         help
 351           Force the SPI max work clock for environment.
 352           If not defined, use CONFIG_SF_DEFAULT_SPEED.
 353
 354 config ENV_SPI_MAX_HZ
 355         int "Value of SPI flash max frequency for environment"
 356         depends on USE_ENV_SPI_MAX_HZ
 357         help
 358           Value of the SPI max work clock for environment.
 359
 360 config USE_ENV_SPI_MODE
 361         bool "SPI flash mode for environment"
 362         depends on ENV_IS_IN_SPI_FLASH
 363         help
 364           Force the SPI work mode for environment.
 365
 366 config ENV_SPI_MODE
 367         hex "Value of SPI flash work mode for environment"
 368         depends on USE_ENV_SPI_MODE
 369         help
 370           Value of the SPI work mode for environment.
 371           See include/spi.h for value.
 372
 373 config ENV_IS_IN_UBI
 374         bool "Environment in a UBI volume"
 375         depends on !CHAIN_OF_TRUST
 376         help
 377           Define this if you have an UBI volume that you want to use for the
 378           environment.  This has the benefit of wear-leveling the environment
 379           accesses, which is important on NAND.
 380
 381           - CONFIG_ENV_UBI_PART:
 382
 383           Define this to a string that is the mtd partition containing the UBI.
 384
 385           - CONFIG_ENV_UBI_VOLUME:
 386
 387           Define this to the name of the volume that you want to store the
 388           environment in.
 389
 390           - CONFIG_ENV_UBI_VOLUME_REDUND:
 391
 392           Define this to the name of another volume to store a second copy of
 393           the environment in.  This will enable redundant environments in UBI.
 394           It is assumed that both volumes are in the same MTD partition.
 395
 396 config ENV_FAT_INTERFACE
 397         string "Name of the block device for the environment"
 398         depends on ENV_IS_IN_FAT
 399         default "mmc" if ARCH_SUNXI
 400         default "mmc" if TI_COMMON_CMD_OPTIONS || ARCH_ZYNQMP || ARCH_AT91
 401         help
 402           Define this to a string that is the name of the block device.
 403
 404 config ENV_FAT_DEVICE_AND_PART
 405         string "Device and partition for where to store the environemt in FAT"
 406         depends on ENV_IS_IN_FAT
 407         default "0:1" if TI_COMMON_CMD_OPTIONS
 408         default "0:auto" if ARCH_ZYNQMP
 409         default "0:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA = -1
 410         default "1:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA != -1
 411         default "0" if ARCH_AT91
 412         help
 413           Define this to a string to specify the partition of the device. It can
 414           be as following:
 415
 416             "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
 417                - "D:P": device D partition P. Error occurs if device D has no
 418                         partition table.
 419                - "D:0": device D.
 420                - "D" or "D:": device D partition 1 if device D has partition
 421                               table, or the whole device D if has no partition
 422                               table.
 423                - "D:auto": first partition in device D with bootable flag set.
 424                            If none, first valid partition in device D. If no
 425                            partition table then means device D.
 426
 427 config ENV_FAT_FILE
 428         string "Name of the FAT file to use for the environment"
 429         depends on ENV_IS_IN_FAT
 430         default "uboot.env"
 431         help
 432           It's a string of the FAT file name. This file use to store the
 433           environment.
 434
 435 config ENV_EXT4_INTERFACE
 436         string "Name of the block device for the environment"
 437         depends on ENV_IS_IN_EXT4
 438         help
 439           Define this to a string that is the name of the block device.
 440
 441 config ENV_EXT4_DEVICE_AND_PART
 442         string "Device and partition for where to store the environemt in EXT4"
 443         depends on ENV_IS_IN_EXT4
 444         help
 445           Define this to a string to specify the partition of the device. It can
 446           be as following:
 447
 448             "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
 449                - "D:P": device D partition P. Error occurs if device D has no
 450                         partition table.
 451                - "D:0": device D.
 452                - "D" or "D:": device D partition 1 if device D has partition
 453                               table, or the whole device D if has no partition
 454                               table.
 455                - "D:auto": first partition in device D with bootable flag set.
 456                            If none, first valid partition in device D. If no
 457                            partition table then means device D.
 458
 459 config ENV_EXT4_FILE
 460         string "Name of the EXT4 file to use for the environment"
 461         depends on ENV_IS_IN_EXT4
 462         default "uboot.env"
 463         help
 464           It's a string of the EXT4 file name. This file use to store the
 465           environment (explicit path to the file)
 466
 467 if ARCH_ROCKCHIP || ARCH_SUNXI || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL || ARC || ARCH_STM32MP
 468
 469 config ENV_OFFSET
 470         hex "Environment Offset"
 471         depends on !ENV_IS_IN_UBI
 472         depends on !ENV_IS_NOWHERE
 473         default 0x3f8000 if ARCH_ROCKCHIP
 474         default 0x88000 if ARCH_SUNXI
 475         default 0xE0000 if ARCH_ZYNQ
 476         default 0x1E00000 if ARCH_ZYNQMP
 477         default 0 if ARC
 478         help
 479           Offset from the start of the device (or partition)
 480
 481 config ENV_SIZE
 482         hex "Environment Size"
 483         default 0x40000 if ENV_IS_IN_SPI_FLASH && ARCH_ZYNQMP
 484         default 0x20000 if ARCH_SUNXI || ARCH_ZYNQ
 485         default 0x8000 if ARCH_ROCKCHIP || ARCH_ZYNQMP || ARCH_VERSAL
 486         default 0x4000 if ARC
 487         help
 488           Size of the environment storage area
 489
 490 config ENV_SECT_SIZE
 491         hex "Environment Sector-Size"
 492         depends on !ENV_IS_NOWHERE && (ARCH_ZYNQ || ARCH_ZYNQMP)
 493         default 0x40000 if ARCH_ZYNQMP
 494         default 0x20000 if ARCH_ZYNQ
 495         help
 496           Size of the sector containing the environment.
 497
 498 config ENV_UBI_PART
 499         string "UBI partition name"
 500         depends on ENV_IS_IN_UBI
 501         help
 502           MTD partition containing the UBI device
 503
 504 config ENV_UBI_VOLUME
 505         string "UBI volume name"
 506         depends on ENV_IS_IN_UBI
 507         help
 508           Name of the volume that you want to store the environment in.
 509
 510 endif
 511
 512 config USE_DEFAULT_ENV_FILE
 513         bool "Create default environment from file"
 514         help
 515           Normally, the default environment is automatically generated
 516           based on the settings of various CONFIG_* options, as well
 517           as the CONFIG_EXTRA_ENV_SETTINGS. By selecting this option,
 518           you can instead define the entire default environment in an
 519           external file.
 520
 521 config DEFAULT_ENV_FILE
 522         string "Path to default environment file"
 523         depends on USE_DEFAULT_ENV_FILE
 524         help
 525           The path containing the default environment. The format is
 526           the same as accepted by the mkenvimage tool: lines
 527           containing key=value pairs, blank lines and lines beginning
 528           with # are ignored.
 529
 530 config ENV_VARS_UBOOT_RUNTIME_CONFIG
 531         bool "Add run-time information to the environment"
 532         help
 533           Enable this in order to add variables describing certain
 534           run-time determined information about the hardware to the
 535           environment.  These will be named board_name, board_rev.
 536
 537 if SPL_ENV_SUPPORT
 538 config SPL_ENV_IS_NOWHERE
 539         bool "SPL Environment is not stored"
 540         default y if ENV_IS_NOWHERE
 541         help
 542           Similar to ENV_IS_NOWHERE, used for SPL environment.
 543
 544 config SPL_ENV_IS_IN_MMC
 545         bool "SPL Environment in an MMC device"
 546         depends on !SPL_ENV_IS_NOWHERE
 547         depends on ENV_IS_IN_MMC
 548         default y
 549         help
 550           Similar to ENV_IS_IN_MMC, used for SPL environment.
 551
 552 config SPL_ENV_IS_IN_FAT
 553         bool "SPL Environment is in a FAT filesystem"
 554         depends on !SPL_ENV_IS_NOWHERE
 555         depends on ENV_IS_IN_FAT
 556         default y
 557         help
 558           Similar to ENV_IS_IN_FAT, used for SPL environment.
 559
 560 config SPL_ENV_IS_IN_EXT4
 561         bool "SPL Environment is in a EXT4 filesystem"
 562         depends on !SPL_ENV_IS_NOWHERE
 563         depends on ENV_IS_IN_EXT4
 564         default y
 565         help
 566           Similar to ENV_IS_IN_EXT4, used for SPL environment.
 567
 568 config SPL_ENV_IS_IN_NAND
 569         bool "SPL Environment in a NAND device"
 570         depends on !SPL_ENV_IS_NOWHERE
 571         depends on ENV_IS_IN_NAND
 572         default y
 573         help
 574           Similar to ENV_IS_IN_NAND, used for SPL environment.
 575
 576 config SPL_ENV_IS_IN_SPI_FLASH
 577         bool "SPL Environment is in SPI flash"
 578         depends on !SPL_ENV_IS_NOWHERE
 579         depends on ENV_IS_IN_SPI_FLASH
 580         default y
 581         help
 582           Similar to ENV_IS_IN_SPI_FLASH, used for SPL environment.
 583
 584 config SPL_ENV_IS_IN_FLASH
 585         bool "SPL Environment in flash memory"
 586         depends on !SPL_ENV_IS_NOWHERE
 587         depends on ENV_IS_IN_FLASH
 588         default y
 589         help
 590           Similar to ENV_IS_IN_FLASH, used for SPL environment.
 591
 592 endif
 593
 594 if TPL_ENV_SUPPORT
 595
 596 config TPL_ENV_IS_NOWHERE
 597         bool "TPL Environment is not stored"
 598         default y if ENV_IS_NOWHERE
 599         help
 600           Similar to ENV_IS_NOWHERE, used for TPL environment.
 601
 602 config TPL_ENV_IS_IN_MMC
 603         bool "TPL Environment in an MMC device"
 604         depends on !TPL_ENV_IS_NOWHERE
 605         depends on ENV_IS_IN_MMC
 606         default y
 607         help
 608           Similar to ENV_IS_IN_MMC, used for TPL environment.
 609
 610 config TPL_ENV_IS_IN_FAT
 611         bool "TPL Environment is in a FAT filesystem"
 612         depends on !TPL_ENV_IS_NOWHERE
 613         depends on ENV_IS_IN_FAT
 614         default y
 615         help
 616           Similar to ENV_IS_IN_FAT, used for TPL environment.
 617
 618 config TPL_ENV_IS_IN_EXT4
 619         bool "TPL Environment is in a EXT4 filesystem"
 620         depends on !TPL_ENV_IS_NOWHERE
 621         depends on ENV_IS_IN_EXT4
 622         default y
 623         help
 624           Similar to ENV_IS_IN_EXT4, used for TPL environment.
 625
 626 config TPL_ENV_IS_IN_NAND
 627         bool "TPL Environment in a NAND device"
 628         depends on !TPL_ENV_IS_NOWHERE
 629         depends on ENV_IS_IN_NAND
 630         default y
 631         help
 632           Similar to ENV_IS_IN_NAND, used for TPL environment.
 633
 634 config TPL_ENV_IS_IN_SPI_FLASH
 635         bool "TPL Environment is in SPI flash"
 636         depends on !TPL_ENV_IS_NOWHERE
 637         depends on ENV_IS_IN_SPI_FLASH
 638         default y
 639         help
 640           Similar to ENV_IS_IN_SPI_FLASH, used for TPL environment.
 641
 642 config TPL_ENV_IS_IN_FLASH
 643         bool "TPL Environment in flash memory"
 644         depends on !TPL_ENV_IS_NOWHERE
 645         depends on ENV_IS_IN_FLASH
 646         default y
 647         help
 648           Similar to ENV_IS_IN_FLASH, used for TPL environment.
 649
 650 endif
 651
 652 endmenu