From f8b0010dfb548469686049f85076fd6a3a6bca2e Mon Sep 17 00:00:00 2001 From: Rodrigo Balerdi Date: Thu, 7 Apr 2022 03:18:59 -0300 Subject: [PATCH] ipq806x: add support for Arris TR4400 v2 / RAC2V1A Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost . Signed-off-by: Rodrigo Balerdi [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo --- package/boot/uboot-envtools/files/ipq806x | 1 + .../ipq806x/base-files/etc/board.d/02_network | 5 + .../base-files/lib/upgrade/platform.sh | 1 + .../arm/boot/dts/qcom-ipq8065-tr4400-v2.dts | 425 ++++++++++++++++++ target/linux/ipq806x/image/generic.mk | 13 + .../0069-arm-boot-add-dts-files.patch | 3 +- .../0069-arm-boot-add-dts-files.patch | 5 +- 7 files changed, 450 insertions(+), 3 deletions(-) create mode 100644 target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts diff --git a/package/boot/uboot-envtools/files/ipq806x b/package/boot/uboot-envtools/files/ipq806x index 7e1d71a7e9..a8285d1452 100644 --- a/package/boot/uboot-envtools/files/ipq806x +++ b/package/boot/uboot-envtools/files/ipq806x @@ -30,6 +30,7 @@ ubootenv_mtdinfo () { } case "$board" in +arris,tr4400-v2|\ askey,rt4230w-rev6) ubootenv_add_uci_config "/dev/mtd9" "0x0" "0x40000" "0x20000" ;; diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 4cb691f32e..dc9c11e4ba 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -11,6 +11,11 @@ board_config_update board=$(board_name) case "$board" in +arris,tr4400-v2) + ucidef_set_interfaces_lan_wan "eth1" "eth2" + ucidef_add_switch "switch0" \ + "1:lan" "2:lan" "3:lan" "4:lan" "6u@eth1" "0u@eth0" + ;; askey,rt4230w-rev6 |\ asrock,g10 |\ nec,wg2600hp) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 84ffcd8a15..f9e592f4bd 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -10,6 +10,7 @@ platform_check_image() { platform_do_upgrade() { case "$(board_name)" in + arris,tr4400-v2 |\ askey,rt4230w-rev6 |\ compex,wpq864|\ netgear,d7800 |\ diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts new file mode 100644 index 0000000000..871cc09502 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-tr4400-v2.dts @@ -0,0 +1,425 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "qcom-ipq8065.dtsi" +#include + +/ { + model = "Arris TR4400 v2"; + compatible = "arris,tr4400-v2", "qcom,ipq8065", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + led-boot = &led_status_blue; + led-failsafe = &led_status_red; + led-running = &led_status_blue; + led-upgrade = &led_status_red; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_status_red: status_red { + label = "red:status"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + led_status_blue: status_blue { + label = "blue:status"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio6", "gpio54"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio7", "gpio8"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + rgmii2_pins: rgmii2_pins { + tx { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32"; + input-disable; + }; + }; + + spi_pins: spi_pins { + cs { + pins = "gpio20"; + drive-strength = <12>; + }; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "everspin,mr25h256"; + spi-max-frequency = <40000000>; + reg = <0>; + }; + }; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0000000 0x0040000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x0040000 0x0140000>; + read-only; + }; + partition@180000 { + label = "0:SBL2"; + reg = <0x0180000 0x0140000>; + read-only; + }; + partition@2c0000 { + label = "0:SBL3"; + reg = <0x02c0000 0x0280000>; + read-only; + }; + partition@540000 { + label = "0:DDRCONFIG"; + reg = <0x0540000 0x0120000>; + read-only; + }; + partition@660000 { + label = "0:SSD"; + reg = <0x0660000 0x0120000>; + read-only; + }; + partition@780000 { + label = "0:TZ"; + reg = <0x0780000 0x0280000>; + read-only; + }; + partition@a00000 { + label = "0:RPM"; + reg = <0x0a00000 0x0280000>; + read-only; + }; + partition@c80000 { + label = "0:APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + partition@1180000 { + label = "0:APPSBLENV"; + reg = <0x1180000 0x0080000>; + }; + partition@1200000 { + label = "0:ART"; + reg = <0x1200000 0x0140000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_ART_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + precal_ART_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + stock_partition@1340000 { + label = "stock_rootfs"; + reg = <0x1340000 0x4000000>; + }; + partition@5340000 { + label = "0:BOOTCONFIG"; + reg = <0x5340000 0x0060000>; + read-only; + }; + partition@53a0000 { + label = "0:SBL2_1"; + reg = <0x53a0000 0x0140000>; + read-only; + }; + partition@54e0000 { + label = "0:SBL3_1"; + reg = <0x54e0000 0x0280000>; + read-only; + }; + partition@5760000 { + label = "0:DDRCONFIG_1"; + reg = <0x5760000 0x0120000>; + read-only; + }; + partition@5880000 { + label = "0:SSD_1"; + reg = <0x5880000 0x0120000>; + read-only; + }; + partition@59a0000 { + label = "0:TZ_1"; + reg = <0x59a0000 0x0280000>; + read-only; + }; + partition@5c20000 { + label = "0:RPM_1"; + reg = <0x5c20000 0x0280000>; + read-only; + }; + partition@5ea0000 { + label = "0:BOOTCONFIG1"; + reg = <0x5ea0000 0x0060000>; + read-only; + }; + partition@5f00000 { + label = "0:APPSBL_1"; + reg = <0x5f00000 0x0500000>; + read-only; + }; + stock_partition@6400000 { + label = "stock_rootfs_1"; + reg = <0x6400000 0x4000000>; + }; + stock_partition@a400000 { + label = "stock_fw_env"; + reg = <0xa400000 0x0100000>; + }; + stock_partition@a500000 { + label = "stock_config"; + reg = <0xa500000 0x0800000>; + }; + stock_partition@ad00000 { + label = "stock_PKI"; + reg = <0xad00000 0x0200000>; + }; + stock_partition@af00000 { + label = "stock_scfgmgr"; + reg = <0xaf00000 0x0100000>; + }; + + partition@6400000 { + label = "fw_env"; + reg = <0x6400000 0x0100000>; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_fw_env_0: macaddr@0 { + reg = <0x00 0x6>; + }; + macaddr_fw_env_6: macaddr@6 { + reg = <0x06 0x6>; + }; + macaddr_fw_env_c: macaddr@c { + reg = <0x0c 0x6>; + }; + macaddr_fw_env_12: macaddr@12 { + reg = <0x12 0x6>; + }; + macaddr_fw_env_18: macaddr@18 { + reg = <0x18 0x6>; + }; + }; + partition@6500000 { + label = "ubi"; + reg = <0x6500000 0x9b00000>; + }; + partition@1340000 { + label = "extra"; + reg = <0x1340000 0x4000000>; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + ethernet-phy@0 { + reg = <0x0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy7: ethernet-phy@7 { + reg = <7>; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <0>; + + nvmem-cells = <&macaddr_fw_env_18>; + nvmem-cell-names = "mac-address"; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <1>; + + nvmem-cells = <&macaddr_fw_env_0>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac3 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <3>; + phy-handle = <&phy7>; + + nvmem-cells = <&macaddr_fw_env_6>; + nvmem-cell-names = "mac-address"; +}; + +&adm_dma { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi0: wifi@1,0 { + compatible = "pci168c,0046"; + reg = <0x00010000 0 0 0 0>; + + nvmem-cells = <&precal_ART_1000>, <&macaddr_fw_env_12>; + nvmem-cell-names = "pre-calibration", "mac-address"; + }; + }; +}; + +&pcie1 { + status = "okay"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + max-link-speed = <1>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi1: wifi@1,0 { + compatible = "pci168c,0040"; + reg = <0x00010000 0 0 0 0>; + + nvmem-cells = <&precal_ART_5000>, <&macaddr_fw_env_c>; + nvmem-cell-names = "pre-calibration", "mac-address"; + }; + }; +}; diff --git a/target/linux/ipq806x/image/generic.mk b/target/linux/ipq806x/image/generic.mk index 819c73d338..469f2c654e 100644 --- a/target/linux/ipq806x/image/generic.mk +++ b/target/linux/ipq806x/image/generic.mk @@ -65,6 +65,19 @@ define Device/ZyXELImage append-metadata endef +define Device/arris_tr4400-v2 + $(call Device/LegacyImage) + DEVICE_VENDOR := Arris + DEVICE_MODEL := TR4400 + DEVICE_VARIANT := v2 + SOC := qcom-ipq8065 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ath10k-firmware-qca99x0-ct + KERNEL_IN_UBI := 1 +endef +TARGET_DEVICES += arris_tr4400-v2 + define Device/askey_rt4230w-rev6 $(call Device/LegacyImage) DEVICE_VENDOR := Askey diff --git a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch index 275b960c18..a7eacf311b 100644 --- a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -908,8 +908,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -908,8 +908,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -33,6 +33,7 @@ Signed-off-by: John Crispin + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ + qcom-ipq8065-rt4230w-rev6.dtb \ ++ qcom-ipq8065-tr4400-v2.dtb \ + qcom-ipq8065-xr500.dtb \ + qcom-ipq8068-ecw5410.dtb \ + qcom-ipq8068-mr42.dtb \ diff --git a/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch index db12b32d94..05f39f6465 100644 --- a/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -956,8 +956,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -956,8 +956,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -32,8 +32,9 @@ Signed-off-by: John Crispin + qcom-ipq8064-wxr-2533dhp.dtb \ + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ -+ qcom-ipq8065-xr500.dtb \ + qcom-ipq8065-rt4230w-rev6.dtb \ ++ qcom-ipq8065-tr4400-v2.dtb \ ++ qcom-ipq8065-xr500.dtb \ + qcom-ipq8068-ecw5410.dtb \ + qcom-ipq8068-mr42.dtb \ + qcom-ipq8068-mr52.dtb \ -- 2.30.2