From: Matthew Hagan Date: Sat, 6 Nov 2021 13:50:27 +0000 (+0000) Subject: kernel: 5.10: compress 7xx patch numbering X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fstaging%2Fthess.git;a=commitdiff_plain;h=f2f42a54e8defb110a3e8b2aab833d67f27e2fe3 kernel: 5.10: compress 7xx patch numbering The qca8k patch series brings the numbering to 799. This patch renames 7xx patches to create space for more backports to be added. Signed-off-by: Matthew Hagan [rename 729->719] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch b/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch new file mode 100644 index 0000000000..00be403299 --- /dev/null +++ b/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch @@ -0,0 +1,108 @@ +From c329e5afb42ff0a88285eb4d8a391a18793e4777 Mon Sep 17 00:00:00 2001 +From: David Bauer +Date: Thu, 15 Apr 2021 03:26:50 +0200 +Subject: [PATCH] net: phy: at803x: select correct page on config init + +The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber +as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit +in the chip configure register. + +The driver assumes the copper side is selected on probe, but this might +not be the case depending which page was last selected by the +bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior. + +Select the copper page when probing to circumvent this. + +Signed-off-by: David Bauer +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 50 +++++++++++++++++++++++++++++++++++++++- + 1 file changed, 49 insertions(+), 1 deletion(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -139,6 +139,9 @@ + #define ATH8035_PHY_ID 0x004dd072 + #define AT8030_PHY_ID_MASK 0xffffffef + ++#define AT803X_PAGE_FIBER 0 ++#define AT803X_PAGE_COPPER 1 ++ + MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); + MODULE_AUTHOR("Matus Ujhelyi"); + MODULE_LICENSE("GPL"); +@@ -190,6 +193,35 @@ static int at803x_debug_reg_mask(struct + return phy_write(phydev, AT803X_DEBUG_DATA, val); + } + ++static int at803x_write_page(struct phy_device *phydev, int page) ++{ ++ int mask; ++ int set; ++ ++ if (page == AT803X_PAGE_COPPER) { ++ set = AT803X_BT_BX_REG_SEL; ++ mask = 0; ++ } else { ++ set = 0; ++ mask = AT803X_BT_BX_REG_SEL; ++ } ++ ++ return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); ++} ++ ++static int at803x_read_page(struct phy_device *phydev) ++{ ++ int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); ++ ++ if (ccr < 0) ++ return ccr; ++ ++ if (ccr & AT803X_BT_BX_REG_SEL) ++ return AT803X_PAGE_COPPER; ++ ++ return AT803X_PAGE_FIBER; ++} ++ + static int at803x_enable_rx_delay(struct phy_device *phydev) + { + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, +@@ -508,6 +540,7 @@ static int at803x_probe(struct phy_devic + { + struct device *dev = &phydev->mdio.dev; + struct at803x_priv *priv; ++ int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) +@@ -515,7 +548,20 @@ static int at803x_probe(struct phy_devic + + phydev->priv = priv; + +- return at803x_parse_dt(phydev); ++ ret = at803x_parse_dt(phydev); ++ if (ret) ++ return ret; ++ ++ /* Some bootloaders leave the fiber page selected. ++ * Switch to the copper page, as otherwise we read ++ * the PHY capabilities from the fiber side. ++ */ ++ if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { ++ ret = phy_select_page(phydev, AT803X_PAGE_COPPER); ++ ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); ++ } ++ ++ return ret; + } + + static void at803x_remove(struct phy_device *phydev) +@@ -1097,6 +1143,8 @@ static struct phy_driver at803x_driver[] + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, ++ .read_page = at803x_read_page, ++ .write_page = at803x_write_page, + /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, + .aneg_done = at803x_aneg_done, diff --git a/target/linux/generic/backport-5.10/706-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch b/target/linux/generic/backport-5.10/706-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch new file mode 100644 index 0000000000..d6ec7450e8 --- /dev/null +++ b/target/linux/generic/backport-5.10/706-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch @@ -0,0 +1,73 @@ +From 8f7e876273e294b732b42af2e5e6bba91d798954 Mon Sep 17 00:00:00 2001 +From: Michael Walle +Date: Tue, 20 Apr 2021 12:29:29 +0200 +Subject: [PATCH] net: phy: at803x: fix probe error if copper page is selected + +The commit c329e5afb42f ("net: phy: at803x: select correct page on +config init") selects the copper page during probe. This fails if the +copper page was already selected. In this case, the value of the copper +page (which is 1) is propagated through phy_restore_page() and is +finally returned for at803x_probe(). Fix it, by just using the +at803x_page_write() directly. + +Also in case of an error, the regulator is not disabled and leads to a +WARN_ON() when the probe fails. This couldn't happen before, because +at803x_parse_dt() was the last call in at803x_probe(). It is hard to +see, that the parse_dt() actually enables the regulator. Thus move the +regulator_enable() to the probe function and undo it in case of an +error. + +Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init") +Signed-off-by: Michael Walle +Reviewed-by: David Bauer +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 23 +++++++++++++++++------ + 1 file changed, 17 insertions(+), 6 deletions(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -527,10 +527,6 @@ static int at803x_parse_dt(struct phy_de + phydev_err(phydev, "failed to get VDDIO regulator\n"); + return PTR_ERR(priv->vddio); + } +- +- ret = regulator_enable(priv->vddio); +- if (ret < 0) +- return ret; + } + + return 0; +@@ -552,15 +548,30 @@ static int at803x_probe(struct phy_devic + if (ret) + return ret; + ++ if (priv->vddio) { ++ ret = regulator_enable(priv->vddio); ++ if (ret < 0) ++ return ret; ++ } ++ + /* Some bootloaders leave the fiber page selected. + * Switch to the copper page, as otherwise we read + * the PHY capabilities from the fiber side. + */ + if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { +- ret = phy_select_page(phydev, AT803X_PAGE_COPPER); +- ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); ++ phy_lock_mdio_bus(phydev); ++ ret = at803x_write_page(phydev, AT803X_PAGE_COPPER); ++ phy_unlock_mdio_bus(phydev); ++ if (ret) ++ goto err; + } + ++ return 0; ++ ++err: ++ if (priv->vddio) ++ regulator_disable(priv->vddio); ++ + return ret; + } + diff --git a/target/linux/generic/backport-5.10/710-v5.12-net-phy-Add-100-base-x-mode.patch b/target/linux/generic/backport-5.10/710-v5.12-net-phy-Add-100-base-x-mode.patch new file mode 100644 index 0000000000..5c7f97ea90 --- /dev/null +++ b/target/linux/generic/backport-5.10/710-v5.12-net-phy-Add-100-base-x-mode.patch @@ -0,0 +1,56 @@ +From b1ae3587d16a8c8fc9453e147c8708d6f006ffbb Mon Sep 17 00:00:00 2001 +From: Bjarni Jonasson +Date: Wed, 13 Jan 2021 12:56:25 +0100 +Subject: [PATCH] net: phy: Add 100 base-x mode + +Sparx-5 supports this mode and it is missing in the PHY core. + +Signed-off-by: Bjarni Jonasson +Reviewed-by: Russell King +Signed-off-by: Jakub Kicinski +--- + Documentation/networking/phy.rst | 5 +++++ + include/linux/phy.h | 4 ++++ + 2 files changed, 9 insertions(+) + +--- a/Documentation/networking/phy.rst ++++ b/Documentation/networking/phy.rst +@@ -286,6 +286,11 @@ Some of the interface modes are describe + Note: due to legacy usage, some 10GBASE-R usage incorrectly makes + use of this definition. + ++``PHY_INTERFACE_MODE_100BASEX`` ++ This defines IEEE 802.3 Clause 24. The link operates at a fixed data ++ rate of 125Mpbs using a 4B/5B encoding scheme, resulting in an underlying ++ data rate of 100Mpbs. ++ + Pause frames / flow control + =========================== + +--- a/include/linux/phy.h ++++ b/include/linux/phy.h +@@ -104,6 +104,7 @@ extern const int phy_10gbit_features_arr + * @PHY_INTERFACE_MODE_MOCA: Multimedia over Coax + * @PHY_INTERFACE_MODE_QSGMII: Quad SGMII + * @PHY_INTERFACE_MODE_TRGMII: Turbo RGMII ++ * @PHY_INTERFACE_MODE_100BASEX: 100 BaseX + * @PHY_INTERFACE_MODE_1000BASEX: 1000 BaseX + * @PHY_INTERFACE_MODE_2500BASEX: 2500 BaseX + * @PHY_INTERFACE_MODE_RXAUI: Reduced XAUI +@@ -135,6 +136,7 @@ typedef enum { + PHY_INTERFACE_MODE_MOCA, + PHY_INTERFACE_MODE_QSGMII, + PHY_INTERFACE_MODE_TRGMII, ++ PHY_INTERFACE_MODE_100BASEX, + PHY_INTERFACE_MODE_1000BASEX, + PHY_INTERFACE_MODE_2500BASEX, + PHY_INTERFACE_MODE_RXAUI, +@@ -217,6 +219,8 @@ static inline const char *phy_modes(phy_ + return "usxgmii"; + case PHY_INTERFACE_MODE_10GKR: + return "10gbase-kr"; ++ case PHY_INTERFACE_MODE_100BASEX: ++ return "100base-x"; + default: + return "unknown"; + } diff --git a/target/linux/generic/backport-5.10/711-v5.12-sfp-add-support-for-100-base-x-SFPs.patch b/target/linux/generic/backport-5.10/711-v5.12-sfp-add-support-for-100-base-x-SFPs.patch new file mode 100644 index 0000000000..7d06c235d9 --- /dev/null +++ b/target/linux/generic/backport-5.10/711-v5.12-sfp-add-support-for-100-base-x-SFPs.patch @@ -0,0 +1,40 @@ +From 6e12f35cef6b8a458d7ecf507ae330e0bffaad8c Mon Sep 17 00:00:00 2001 +From: Bjarni Jonasson +Date: Wed, 13 Jan 2021 12:56:26 +0100 +Subject: [PATCH] sfp: add support for 100 base-x SFPs + +Add support for 100Base-FX, 100Base-LX, 100Base-PX and 100Base-BX10 modules +This is needed for Sparx-5 switch. + +Signed-off-by: Bjarni Jonasson +Reviewed-by: Russell King +Signed-off-by: Jakub Kicinski +--- + drivers/net/phy/sfp-bus.c | 9 +++++++++ + 1 file changed, 9 insertions(+) + +--- a/drivers/net/phy/sfp-bus.c ++++ b/drivers/net/phy/sfp-bus.c +@@ -280,6 +280,12 @@ void sfp_parse_support(struct sfp_bus *b + br_min <= 1300 && br_max >= 1200) + phylink_set(modes, 1000baseX_Full); + ++ /* 100Base-FX, 100Base-LX, 100Base-PX, 100Base-BX10 */ ++ if (id->base.e100_base_fx || id->base.e100_base_lx) ++ phylink_set(modes, 100baseFX_Full); ++ if ((id->base.e_base_px || id->base.e_base_bx10) && br_nom == 100) ++ phylink_set(modes, 100baseFX_Full); ++ + /* For active or passive cables, select the link modes + * based on the bit rates and the cable compliance bytes. + */ +@@ -399,6 +405,9 @@ phy_interface_t sfp_select_interface(str + if (phylink_test(link_modes, 1000baseX_Full)) + return PHY_INTERFACE_MODE_1000BASEX; + ++ if (phylink_test(link_modes, 100baseFX_Full)) ++ return PHY_INTERFACE_MODE_100BASEX; ++ + dev_warn(bus->sfp_dev, "Unable to ascertain link mode\n"); + + return PHY_INTERFACE_MODE_NA; diff --git a/target/linux/generic/backport-5.10/712-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch b/target/linux/generic/backport-5.10/712-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch new file mode 100644 index 0000000000..7bf59267fa --- /dev/null +++ b/target/linux/generic/backport-5.10/712-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch @@ -0,0 +1,549 @@ +From 41d26bf4aba070dfd2ab48866cc27a48ee6228c7 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Marek=20Beh=C3=BAn?= +Date: Tue, 20 Apr 2021 09:53:59 +0200 +Subject: [PATCH] net: phy: marvell: refactor HWMON OOP style +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Use a structure of Marvell PHY specific HWMON methods to reduce code +duplication. Store a pointer to this structure into the PHY driver's +driver_data member. + +Signed-off-by: Marek Behún +Signed-off-by: David S. Miller +--- + drivers/net/phy/marvell.c | 369 +++++++++++++------------------------- + 1 file changed, 125 insertions(+), 244 deletions(-) + +--- a/drivers/net/phy/marvell.c ++++ b/drivers/net/phy/marvell.c +@@ -2134,6 +2134,19 @@ static int marvell_vct7_cable_test_get_s + } + + #ifdef CONFIG_HWMON ++struct marvell_hwmon_ops { ++ int (*get_temp)(struct phy_device *phydev, long *temp); ++ int (*get_temp_critical)(struct phy_device *phydev, long *temp); ++ int (*set_temp_critical)(struct phy_device *phydev, long temp); ++ int (*get_temp_alarm)(struct phy_device *phydev, long *alarm); ++}; ++ ++static const struct marvell_hwmon_ops * ++to_marvell_hwmon_ops(const struct phy_device *phydev) ++{ ++ return phydev->drv->driver_data; ++} ++ + static int m88e1121_get_temp(struct phy_device *phydev, long *temp) + { + int oldpage; +@@ -2177,75 +2190,6 @@ error: + return phy_restore_page(phydev, oldpage, ret); + } + +-static int m88e1121_hwmon_read(struct device *dev, +- enum hwmon_sensor_types type, +- u32 attr, int channel, long *temp) +-{ +- struct phy_device *phydev = dev_get_drvdata(dev); +- int err; +- +- switch (attr) { +- case hwmon_temp_input: +- err = m88e1121_get_temp(phydev, temp); +- break; +- default: +- return -EOPNOTSUPP; +- } +- +- return err; +-} +- +-static umode_t m88e1121_hwmon_is_visible(const void *data, +- enum hwmon_sensor_types type, +- u32 attr, int channel) +-{ +- if (type != hwmon_temp) +- return 0; +- +- switch (attr) { +- case hwmon_temp_input: +- return 0444; +- default: +- return 0; +- } +-} +- +-static u32 m88e1121_hwmon_chip_config[] = { +- HWMON_C_REGISTER_TZ, +- 0 +-}; +- +-static const struct hwmon_channel_info m88e1121_hwmon_chip = { +- .type = hwmon_chip, +- .config = m88e1121_hwmon_chip_config, +-}; +- +-static u32 m88e1121_hwmon_temp_config[] = { +- HWMON_T_INPUT, +- 0 +-}; +- +-static const struct hwmon_channel_info m88e1121_hwmon_temp = { +- .type = hwmon_temp, +- .config = m88e1121_hwmon_temp_config, +-}; +- +-static const struct hwmon_channel_info *m88e1121_hwmon_info[] = { +- &m88e1121_hwmon_chip, +- &m88e1121_hwmon_temp, +- NULL +-}; +- +-static const struct hwmon_ops m88e1121_hwmon_hwmon_ops = { +- .is_visible = m88e1121_hwmon_is_visible, +- .read = m88e1121_hwmon_read, +-}; +- +-static const struct hwmon_chip_info m88e1121_hwmon_chip_info = { +- .ops = &m88e1121_hwmon_hwmon_ops, +- .info = m88e1121_hwmon_info, +-}; +- + static int m88e1510_get_temp(struct phy_device *phydev, long *temp) + { + int ret; +@@ -2308,92 +2252,6 @@ static int m88e1510_get_temp_alarm(struc + return 0; + } + +-static int m88e1510_hwmon_read(struct device *dev, +- enum hwmon_sensor_types type, +- u32 attr, int channel, long *temp) +-{ +- struct phy_device *phydev = dev_get_drvdata(dev); +- int err; +- +- switch (attr) { +- case hwmon_temp_input: +- err = m88e1510_get_temp(phydev, temp); +- break; +- case hwmon_temp_crit: +- err = m88e1510_get_temp_critical(phydev, temp); +- break; +- case hwmon_temp_max_alarm: +- err = m88e1510_get_temp_alarm(phydev, temp); +- break; +- default: +- return -EOPNOTSUPP; +- } +- +- return err; +-} +- +-static int m88e1510_hwmon_write(struct device *dev, +- enum hwmon_sensor_types type, +- u32 attr, int channel, long temp) +-{ +- struct phy_device *phydev = dev_get_drvdata(dev); +- int err; +- +- switch (attr) { +- case hwmon_temp_crit: +- err = m88e1510_set_temp_critical(phydev, temp); +- break; +- default: +- return -EOPNOTSUPP; +- } +- return err; +-} +- +-static umode_t m88e1510_hwmon_is_visible(const void *data, +- enum hwmon_sensor_types type, +- u32 attr, int channel) +-{ +- if (type != hwmon_temp) +- return 0; +- +- switch (attr) { +- case hwmon_temp_input: +- case hwmon_temp_max_alarm: +- return 0444; +- case hwmon_temp_crit: +- return 0644; +- default: +- return 0; +- } +-} +- +-static u32 m88e1510_hwmon_temp_config[] = { +- HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_MAX_ALARM, +- 0 +-}; +- +-static const struct hwmon_channel_info m88e1510_hwmon_temp = { +- .type = hwmon_temp, +- .config = m88e1510_hwmon_temp_config, +-}; +- +-static const struct hwmon_channel_info *m88e1510_hwmon_info[] = { +- &m88e1121_hwmon_chip, +- &m88e1510_hwmon_temp, +- NULL +-}; +- +-static const struct hwmon_ops m88e1510_hwmon_hwmon_ops = { +- .is_visible = m88e1510_hwmon_is_visible, +- .read = m88e1510_hwmon_read, +- .write = m88e1510_hwmon_write, +-}; +- +-static const struct hwmon_chip_info m88e1510_hwmon_chip_info = { +- .ops = &m88e1510_hwmon_hwmon_ops, +- .info = m88e1510_hwmon_info, +-}; +- + static int m88e6390_get_temp(struct phy_device *phydev, long *temp) + { + int sum = 0; +@@ -2452,63 +2310,112 @@ error: + return ret; + } + +-static int m88e6390_hwmon_read(struct device *dev, +- enum hwmon_sensor_types type, +- u32 attr, int channel, long *temp) ++static int marvell_hwmon_read(struct device *dev, enum hwmon_sensor_types type, ++ u32 attr, int channel, long *temp) + { + struct phy_device *phydev = dev_get_drvdata(dev); +- int err; ++ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); ++ int err = -EOPNOTSUPP; + + switch (attr) { + case hwmon_temp_input: +- err = m88e6390_get_temp(phydev, temp); ++ if (ops->get_temp) ++ err = ops->get_temp(phydev, temp); ++ break; ++ case hwmon_temp_crit: ++ if (ops->get_temp_critical) ++ err = ops->get_temp_critical(phydev, temp); ++ break; ++ case hwmon_temp_max_alarm: ++ if (ops->get_temp_alarm) ++ err = ops->get_temp_alarm(phydev, temp); ++ break; ++ } ++ ++ return err; ++} ++ ++static int marvell_hwmon_write(struct device *dev, enum hwmon_sensor_types type, ++ u32 attr, int channel, long temp) ++{ ++ struct phy_device *phydev = dev_get_drvdata(dev); ++ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); ++ int err = -EOPNOTSUPP; ++ ++ switch (attr) { ++ case hwmon_temp_crit: ++ if (ops->set_temp_critical) ++ err = ops->set_temp_critical(phydev, temp); + break; + default: +- return -EOPNOTSUPP; ++ fallthrough; + } + + return err; + } + +-static umode_t m88e6390_hwmon_is_visible(const void *data, +- enum hwmon_sensor_types type, +- u32 attr, int channel) ++static umode_t marvell_hwmon_is_visible(const void *data, ++ enum hwmon_sensor_types type, ++ u32 attr, int channel) + { ++ const struct phy_device *phydev = data; ++ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); ++ + if (type != hwmon_temp) + return 0; + + switch (attr) { + case hwmon_temp_input: +- return 0444; ++ return ops->get_temp ? 0444 : 0; ++ case hwmon_temp_max_alarm: ++ return ops->get_temp_alarm ? 0444 : 0; ++ case hwmon_temp_crit: ++ return (ops->get_temp_critical ? 0444 : 0) | ++ (ops->set_temp_critical ? 0200 : 0); + default: + return 0; + } + } + +-static u32 m88e6390_hwmon_temp_config[] = { +- HWMON_T_INPUT, ++static u32 marvell_hwmon_chip_config[] = { ++ HWMON_C_REGISTER_TZ, + 0 + }; + +-static const struct hwmon_channel_info m88e6390_hwmon_temp = { ++static const struct hwmon_channel_info marvell_hwmon_chip = { ++ .type = hwmon_chip, ++ .config = marvell_hwmon_chip_config, ++}; ++ ++/* we can define HWMON_T_CRIT and HWMON_T_MAX_ALARM even though these are not ++ * defined for all PHYs, because the hwmon code checks whether the attributes ++ * exists via the .is_visible method ++ */ ++static u32 marvell_hwmon_temp_config[] = { ++ HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_MAX_ALARM, ++ 0 ++}; ++ ++static const struct hwmon_channel_info marvell_hwmon_temp = { + .type = hwmon_temp, +- .config = m88e6390_hwmon_temp_config, ++ .config = marvell_hwmon_temp_config, + }; + +-static const struct hwmon_channel_info *m88e6390_hwmon_info[] = { +- &m88e1121_hwmon_chip, +- &m88e6390_hwmon_temp, ++static const struct hwmon_channel_info *marvell_hwmon_info[] = { ++ &marvell_hwmon_chip, ++ &marvell_hwmon_temp, + NULL + }; + +-static const struct hwmon_ops m88e6390_hwmon_hwmon_ops = { +- .is_visible = m88e6390_hwmon_is_visible, +- .read = m88e6390_hwmon_read, ++static const struct hwmon_ops marvell_hwmon_hwmon_ops = { ++ .is_visible = marvell_hwmon_is_visible, ++ .read = marvell_hwmon_read, ++ .write = marvell_hwmon_write, + }; + +-static const struct hwmon_chip_info m88e6390_hwmon_chip_info = { +- .ops = &m88e6390_hwmon_hwmon_ops, +- .info = m88e6390_hwmon_info, ++static const struct hwmon_chip_info marvell_hwmon_chip_info = { ++ .ops = &marvell_hwmon_hwmon_ops, ++ .info = marvell_hwmon_info, + }; + + static int marvell_hwmon_name(struct phy_device *phydev) +@@ -2531,49 +2438,48 @@ static int marvell_hwmon_name(struct phy + return 0; + } + +-static int marvell_hwmon_probe(struct phy_device *phydev, +- const struct hwmon_chip_info *chip) ++static int marvell_hwmon_probe(struct phy_device *phydev) + { ++ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); + struct marvell_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + int err; + ++ if (!ops) ++ return 0; ++ + err = marvell_hwmon_name(phydev); + if (err) + return err; + + priv->hwmon_dev = devm_hwmon_device_register_with_info( +- dev, priv->hwmon_name, phydev, chip, NULL); ++ dev, priv->hwmon_name, phydev, &marvell_hwmon_chip_info, NULL); + + return PTR_ERR_OR_ZERO(priv->hwmon_dev); + } + +-static int m88e1121_hwmon_probe(struct phy_device *phydev) +-{ +- return marvell_hwmon_probe(phydev, &m88e1121_hwmon_chip_info); +-} ++static const struct marvell_hwmon_ops m88e1121_hwmon_ops = { ++ .get_temp = m88e1121_get_temp, ++}; + +-static int m88e1510_hwmon_probe(struct phy_device *phydev) +-{ +- return marvell_hwmon_probe(phydev, &m88e1510_hwmon_chip_info); +-} ++static const struct marvell_hwmon_ops m88e1510_hwmon_ops = { ++ .get_temp = m88e1510_get_temp, ++ .get_temp_critical = m88e1510_get_temp_critical, ++ .set_temp_critical = m88e1510_set_temp_critical, ++ .get_temp_alarm = m88e1510_get_temp_alarm, ++}; ++ ++static const struct marvell_hwmon_ops m88e6390_hwmon_ops = { ++ .get_temp = m88e6390_get_temp, ++}; ++ ++#define DEF_MARVELL_HWMON_OPS(s) (&(s)) + +-static int m88e6390_hwmon_probe(struct phy_device *phydev) +-{ +- return marvell_hwmon_probe(phydev, &m88e6390_hwmon_chip_info); +-} + #else +-static int m88e1121_hwmon_probe(struct phy_device *phydev) +-{ +- return 0; +-} + +-static int m88e1510_hwmon_probe(struct phy_device *phydev) +-{ +- return 0; +-} ++#define DEF_MARVELL_HWMON_OPS(s) NULL + +-static int m88e6390_hwmon_probe(struct phy_device *phydev) ++static int marvell_hwmon_probe(struct phy_device *phydev) + { + return 0; + } +@@ -2589,40 +2495,7 @@ static int marvell_probe(struct phy_devi + + phydev->priv = priv; + +- return 0; +-} +- +-static int m88e1121_probe(struct phy_device *phydev) +-{ +- int err; +- +- err = marvell_probe(phydev); +- if (err) +- return err; +- +- return m88e1121_hwmon_probe(phydev); +-} +- +-static int m88e1510_probe(struct phy_device *phydev) +-{ +- int err; +- +- err = marvell_probe(phydev); +- if (err) +- return err; +- +- return m88e1510_hwmon_probe(phydev); +-} +- +-static int m88e6390_probe(struct phy_device *phydev) +-{ +- int err; +- +- err = marvell_probe(phydev); +- if (err) +- return err; +- +- return m88e6390_hwmon_probe(phydev); ++ return marvell_hwmon_probe(phydev); + } + + static struct phy_driver marvell_drivers[] = { +@@ -2707,8 +2580,9 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1121R, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1121R", ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1121_hwmon_ops), + /* PHY_GBIT_FEATURES */ +- .probe = m88e1121_probe, ++ .probe = marvell_probe, + .config_init = marvell_config_init, + .config_aneg = m88e1121_config_aneg, + .read_status = marvell_read_status, +@@ -2827,9 +2701,10 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1510, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1510", ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), + .features = PHY_GBIT_FIBRE_FEATURES, + .flags = PHY_POLL_CABLE_TEST, +- .probe = m88e1510_probe, ++ .probe = marvell_probe, + .config_init = m88e1510_config_init, + .config_aneg = m88e1510_config_aneg, + .read_status = marvell_read_status, +@@ -2856,9 +2731,10 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1540, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1540", ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), + /* PHY_GBIT_FEATURES */ + .flags = PHY_POLL_CABLE_TEST, +- .probe = m88e1510_probe, ++ .probe = marvell_probe, + .config_init = marvell_config_init, + .config_aneg = m88e1510_config_aneg, + .read_status = marvell_read_status, +@@ -2882,7 +2758,8 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1545, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1545", +- .probe = m88e1510_probe, ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), ++ .probe = marvell_probe, + /* PHY_GBIT_FEATURES */ + .flags = PHY_POLL_CABLE_TEST, + .config_init = marvell_config_init, +@@ -2928,9 +2805,10 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E6341_FAMILY, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E6341 Family", ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), + /* PHY_GBIT_FEATURES */ + .flags = PHY_POLL_CABLE_TEST, +- .probe = m88e1510_probe, ++ .probe = marvell_probe, + .config_init = marvell_config_init, + .config_aneg = m88e6390_config_aneg, + .read_status = marvell_read_status, +@@ -2954,9 +2832,10 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E6390_FAMILY, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E6390 Family", ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e6390_hwmon_ops), + /* PHY_GBIT_FEATURES */ + .flags = PHY_POLL_CABLE_TEST, +- .probe = m88e6390_probe, ++ .probe = marvell_probe, + .config_init = marvell_config_init, + .config_aneg = m88e6390_config_aneg, + .read_status = marvell_read_status, +@@ -2980,7 +2859,8 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1340S, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1340S", +- .probe = m88e1510_probe, ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), ++ .probe = marvell_probe, + /* PHY_GBIT_FEATURES */ + .config_init = marvell_config_init, + .config_aneg = m88e1510_config_aneg, +@@ -3002,7 +2882,8 @@ static struct phy_driver marvell_drivers + .phy_id = MARVELL_PHY_ID_88E1548P, + .phy_id_mask = MARVELL_PHY_ID_MASK, + .name = "Marvell 88E1548P", +- .probe = m88e1510_probe, ++ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), ++ .probe = marvell_probe, + .features = PHY_GBIT_FIBRE_FEATURES, + .config_init = marvell_config_init, + .config_aneg = m88e1510_config_aneg, diff --git a/target/linux/generic/backport-5.10/713-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch b/target/linux/generic/backport-5.10/713-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch new file mode 100644 index 0000000000..7fb78089f2 --- /dev/null +++ b/target/linux/generic/backport-5.10/713-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch @@ -0,0 +1,161 @@ +From b697d9d38a5a5ab405d7cc4743d39fe2c5d7517c Mon Sep 17 00:00:00 2001 +From: Ivan Bornyakov +Date: Thu, 12 Aug 2021 16:42:56 +0300 +Subject: [PATCH] net: phy: marvell: add SFP support for 88E1510 + +Add support for SFP cages connected to the Marvell 88E1512 transceiver. +88E1512 supports for SGMII/1000Base-X/100Base-FX media type with RGMII +on system interface. Configure PHY to appropriate mode depending on the +type of SFP inserted. On SFP removal configure PHY to the RGMII-copper +mode so RJ-45 port can still work. + +Signed-off-by: Ivan Bornyakov +Link: https://lore.kernel.org/r/20210812134256.2436-1-i.bornyakov@metrotek.ru +Signed-off-by: Jakub Kicinski +--- + drivers/net/phy/marvell.c | 105 +++++++++++++++++++++++++++++++++++++- + 1 file changed, 104 insertions(+), 1 deletion(-) + +--- a/drivers/net/phy/marvell.c ++++ b/drivers/net/phy/marvell.c +@@ -32,6 +32,7 @@ + #include + #include + #include ++#include + + #include + #include +@@ -46,6 +47,7 @@ + #define MII_MARVELL_MISC_TEST_PAGE 0x06 + #define MII_MARVELL_VCT7_PAGE 0x07 + #define MII_MARVELL_WOL_PAGE 0x11 ++#define MII_MARVELL_MODE_PAGE 0x12 + + #define MII_M1011_IEVENT 0x13 + #define MII_M1011_IEVENT_CLEAR 0x0000 +@@ -162,7 +164,14 @@ + + #define MII_88E1510_GEN_CTRL_REG_1 0x14 + #define MII_88E1510_GEN_CTRL_REG_1_MODE_MASK 0x7 ++#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII 0x0 /* RGMII to copper */ + #define MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII 0x1 /* SGMII to copper */ ++/* RGMII to 1000BASE-X */ ++#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X 0x2 ++/* RGMII to 100BASE-FX */ ++#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX 0x3 ++/* RGMII to SGMII */ ++#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII 0x4 + #define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */ + + #define MII_VCT5_TX_RX_MDI0_COUPLING 0x10 +@@ -2498,6 +2507,100 @@ static int marvell_probe(struct phy_devi + return marvell_hwmon_probe(phydev); + } + ++static int m88e1510_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) ++{ ++ struct phy_device *phydev = upstream; ++ phy_interface_t interface; ++ struct device *dev; ++ int oldpage; ++ int ret = 0; ++ u16 mode; ++ ++ __ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, }; ++ ++ dev = &phydev->mdio.dev; ++ ++ sfp_parse_support(phydev->sfp_bus, id, supported); ++ interface = sfp_select_interface(phydev->sfp_bus, supported); ++ ++ dev_info(dev, "%s SFP module inserted\n", phy_modes(interface)); ++ ++ switch (interface) { ++ case PHY_INTERFACE_MODE_1000BASEX: ++ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X; ++ ++ break; ++ case PHY_INTERFACE_MODE_100BASEX: ++ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX; ++ ++ break; ++ case PHY_INTERFACE_MODE_SGMII: ++ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII; ++ ++ break; ++ default: ++ dev_err(dev, "Incompatible SFP module inserted\n"); ++ ++ return -EINVAL; ++ } ++ ++ oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE); ++ if (oldpage < 0) ++ goto error; ++ ++ ret = __phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1, ++ MII_88E1510_GEN_CTRL_REG_1_MODE_MASK, mode); ++ if (ret < 0) ++ goto error; ++ ++ ret = __phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1, ++ MII_88E1510_GEN_CTRL_REG_1_RESET); ++ ++error: ++ return phy_restore_page(phydev, oldpage, ret); ++} ++ ++static void m88e1510_sfp_remove(void *upstream) ++{ ++ struct phy_device *phydev = upstream; ++ int oldpage; ++ int ret = 0; ++ ++ oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE); ++ if (oldpage < 0) ++ goto error; ++ ++ ret = __phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1, ++ MII_88E1510_GEN_CTRL_REG_1_MODE_MASK, ++ MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII); ++ if (ret < 0) ++ goto error; ++ ++ ret = __phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1, ++ MII_88E1510_GEN_CTRL_REG_1_RESET); ++ ++error: ++ phy_restore_page(phydev, oldpage, ret); ++} ++ ++static const struct sfp_upstream_ops m88e1510_sfp_ops = { ++ .module_insert = m88e1510_sfp_insert, ++ .module_remove = m88e1510_sfp_remove, ++ .attach = phy_sfp_attach, ++ .detach = phy_sfp_detach, ++}; ++ ++static int m88e1510_probe(struct phy_device *phydev) ++{ ++ int err; ++ ++ err = marvell_probe(phydev); ++ if (err) ++ return err; ++ ++ return phy_sfp_probe(phydev, &m88e1510_sfp_ops); ++} ++ + static struct phy_driver marvell_drivers[] = { + { + .phy_id = MARVELL_PHY_ID_88E1101, +@@ -2704,7 +2807,7 @@ static struct phy_driver marvell_drivers + .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), + .features = PHY_GBIT_FIBRE_FEATURES, + .flags = PHY_POLL_CABLE_TEST, +- .probe = marvell_probe, ++ .probe = m88e1510_probe, + .config_init = m88e1510_config_init, + .config_aneg = m88e1510_config_aneg, + .read_status = marvell_read_status, diff --git a/target/linux/generic/backport-5.10/719-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch b/target/linux/generic/backport-5.10/719-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch new file mode 100644 index 0000000000..3b630377f9 --- /dev/null +++ b/target/linux/generic/backport-5.10/719-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch @@ -0,0 +1,85 @@ +From 9d5ef190e5615a7b63af89f88c4106a5bc127974 Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Fri, 5 Feb 2021 15:37:10 +0200 +Subject: [PATCH] net: dsa: automatically bring up DSA master when opening user + port + +DSA wants the master interface to be open before the user port is due to +historical reasons. The promiscuity of interfaces that are down used to +have issues, as referenced Lennert Buytenhek in commit df02c6ff2e39 +("dsa: fix master interface allmulti/promisc handling"). + +The bugfix mentioned there, commit b6c40d68ff64 ("net: only invoke +dev->change_rx_flags when device is UP"), was basically a "don't do +that" approach to working around the promiscuity while down issue. + +Further work done by Vlad Yasevich in commit d2615bf45069 ("net: core: +Always propagate flag changes to interfaces") has resolved the +underlying issue, and it is strictly up to the DSA and 8021q drivers +now, it is no longer mandated by the networking core that the master +interface must be up when changing its promiscuity. + +From DSA's point of view, deciding to error out in dsa_slave_open +because the master isn't up is +(a) a bad user experience and +(b) knocking at an open door. +Even if there still was an issue with promiscuity while down, DSA could +still just open the master and avoid it. + +Doing it this way has the additional benefit that user space can now +remove DSA-specific workarounds, like systemd-networkd with BindCarrier: +https://github.com/systemd/systemd/issues/7478 + +And we can finally remove one of the 2 bullets in the "Common pitfalls +using DSA setups" chapter. + +Tested with two cascaded DSA switches: + +$ ip link set sw0p2 up +fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode +fsl_enetc 0000:00:00.2 eno2: Link is Up - 1Gbps/Full - flow control rx/tx +mscc_felix 0000:00:00.5 swp0: configuring for fixed/sgmii link mode +mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off +8021q: adding VLAN 0 to HW filter on device swp0 +sja1105 spi2.0 sw0p2: configuring for phy/rgmii-id link mode +IPv6: ADDRCONF(NETDEV_CHANGE): eno2: link becomes ready +IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready + +Signed-off-by: Vladimir Oltean +Reviewed-by: Andrew Lunn +Reviewed-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + Documentation/networking/dsa/dsa.rst | 4 ---- + net/dsa/slave.c | 7 +++++-- + 2 files changed, 5 insertions(+), 6 deletions(-) + +--- a/Documentation/networking/dsa/dsa.rst ++++ b/Documentation/networking/dsa/dsa.rst +@@ -273,10 +273,6 @@ will not make us go through the switch t + the Ethernet switch on the other end, expecting a tag will typically drop this + frame. + +-Slave network devices check that the master network device is UP before allowing +-you to administratively bring UP these slave network devices. A common +-configuration mistake is forgetting to bring UP the master network device first. +- + Interactions with other subsystems + ================================== + +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -68,8 +68,11 @@ static int dsa_slave_open(struct net_dev + struct dsa_port *dp = dsa_slave_to_port(dev); + int err; + +- if (!(master->flags & IFF_UP)) +- return -ENETDOWN; ++ err = dev_open(master, NULL); ++ if (err < 0) { ++ netdev_err(dev, "failed to open master %s\n", master->name); ++ goto out; ++ } + + if (!ether_addr_equal(dev->dev_addr, master->dev_addr)) { + err = dev_uc_add(master, dev->dev_addr); diff --git a/target/linux/generic/backport-5.10/720-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch b/target/linux/generic/backport-5.10/720-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch new file mode 100644 index 0000000000..c43cb4d1f2 --- /dev/null +++ b/target/linux/generic/backport-5.10/720-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch @@ -0,0 +1,126 @@ +From 90dc8fd36078a536671adae884d0b929cce6480a Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:30 +0200 +Subject: [PATCH] net: bridge: notify switchdev of disappearance of old FDB + entry upon migration + +Currently the bridge emits atomic switchdev notifications for +dynamically learnt FDB entries. Monitoring these notifications works +wonders for switchdev drivers that want to keep their hardware FDB in +sync with the bridge's FDB. + +For example station A wants to talk to station B in the diagram below, +and we are concerned with the behavior of the bridge on the DUT device: + + DUT + +-------------------------------------+ + | br0 | + | +------+ +------+ +------+ +------+ | + | | | | | | | | | | + | | swp0 | | swp1 | | swp2 | | eth0 | | + +-------------------------------------+ + | | | + Station A | | + | | + +--+------+--+ +--+------+--+ + | | | | | | | | + | | swp0 | | | | swp0 | | + Another | +------+ | | +------+ | Another + switch | br0 | | br0 | switch + | +------+ | | +------+ | + | | | | | | | | + | | swp1 | | | | swp1 | | + +--+------+--+ +--+------+--+ + | + Station B + +Interfaces swp0, swp1, swp2 are handled by a switchdev driver that has +the following property: frames injected from its control interface bypass +the internal address analyzer logic, and therefore, this hardware does +not learn from the source address of packets transmitted by the network +stack through it. So, since bridging between eth0 (where Station B is +attached) and swp0 (where Station A is attached) is done in software, +the switchdev hardware will never learn the source address of Station B. +So the traffic towards that destination will be treated as unknown, i.e. +flooded. + +This is where the bridge notifications come in handy. When br0 on the +DUT sees frames with Station B's MAC address on eth0, the switchdev +driver gets these notifications and can install a rule to send frames +towards Station B's address that are incoming from swp0, swp1, swp2, +only towards the control interface. This is all switchdev driver private +business, which the notification makes possible. + +All is fine until someone unplugs Station B's cable and moves it to the +other switch: + + DUT + +-------------------------------------+ + | br0 | + | +------+ +------+ +------+ +------+ | + | | | | | | | | | | + | | swp0 | | swp1 | | swp2 | | eth0 | | + +-------------------------------------+ + | | | + Station A | | + | | + +--+------+--+ +--+------+--+ + | | | | | | | | + | | swp0 | | | | swp0 | | + Another | +------+ | | +------+ | Another + switch | br0 | | br0 | switch + | +------+ | | +------+ | + | | | | | | | | + | | swp1 | | | | swp1 | | + +--+------+--+ +--+------+--+ + | + Station B + +Luckily for the use cases we care about, Station B is noisy enough that +the DUT hears it (on swp1 this time). swp1 receives the frames and +delivers them to the bridge, who enters the unlikely path in br_fdb_update +of updating an existing entry. It moves the entry in the software bridge +to swp1 and emits an addition notification towards that. + +As far as the switchdev driver is concerned, all that it needs to ensure +is that traffic between Station A and Station B is not forever broken. +If it does nothing, then the stale rule to send frames for Station B +towards the control interface remains in place. But Station B is no +longer reachable via the control interface, but via a port that can +offload the bridge port learning attribute. It's just that the port is +prevented from learning this address, since the rule overrides FDB +updates. So the rule needs to go. The question is via what mechanism. + +It sure would be possible for this switchdev driver to keep track of all +addresses which are sent to the control interface, and then also listen +for bridge notifier events on its own ports, searching for the ones that +have a MAC address which was previously sent to the control interface. +But this is cumbersome and inefficient. Instead, with one small change, +the bridge could notify of the address deletion from the old port, in a +symmetrical manner with how it did for the insertion. Then the switchdev +driver would not be required to monitor learn/forget events for its own +ports. It could just delete the rule towards the control interface upon +bridge entry migration. This would make hardware address learning be +possible again. Then it would take a few more packets until the hardware +and software FDB would be in sync again. + +Signed-off-by: Vladimir Oltean +Acked-by: Nikolay Aleksandrov +Reviewed-by: Ido Schimmel +Reviewed-by: Andrew Lunn +Reviewed-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + net/bridge/br_fdb.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/net/bridge/br_fdb.c ++++ b/net/bridge/br_fdb.c +@@ -602,6 +602,7 @@ void br_fdb_update(struct net_bridge *br + /* fastpath: update of existing entry */ + if (unlikely(source != fdb->dst && + !test_bit(BR_FDB_STICKY, &fdb->flags))) { ++ br_switchdev_fdb_notify(fdb, RTM_DELNEIGH); + fdb->dst = source; + fdb_modified = true; + /* Take over HW learned entry */ diff --git a/target/linux/generic/backport-5.10/721-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch b/target/linux/generic/backport-5.10/721-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch new file mode 100644 index 0000000000..f9337590f7 --- /dev/null +++ b/target/linux/generic/backport-5.10/721-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch @@ -0,0 +1,52 @@ +From 2fd186501b1cff155cc4a755c210793cfc0dffb5 Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:31 +0200 +Subject: [PATCH] net: dsa: be louder when a non-legacy FDB operation fails + +The dev_close() call was added in commit c9eb3e0f8701 ("net: dsa: Add +support for learning FDB through notification") "to indicate inconsistent +situation" when we could not delete an FDB entry from the port. + +bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master + +It is a bit drastic and at the same time not helpful if the above fails +to only print with netdev_dbg log level, but on the other hand to bring +the interface down. + +So increase the verbosity of the error message, and drop dev_close(). + +Signed-off-by: Vladimir Oltean +Reviewed-by: Andrew Lunn +Reviewed-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + net/dsa/slave.c | 10 +++++++--- + 1 file changed, 7 insertions(+), 3 deletions(-) + +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -2112,7 +2112,9 @@ static void dsa_slave_switchdev_event_wo + + err = dsa_port_fdb_add(dp, fdb_info->addr, fdb_info->vid); + if (err) { +- netdev_dbg(dev, "fdb add failed err=%d\n", err); ++ netdev_err(dev, ++ "failed to add %pM vid %d to fdb: %d\n", ++ fdb_info->addr, fdb_info->vid, err); + break; + } + fdb_info->offloaded = true; +@@ -2127,9 +2129,11 @@ static void dsa_slave_switchdev_event_wo + + err = dsa_port_fdb_del(dp, fdb_info->addr, fdb_info->vid); + if (err) { +- netdev_dbg(dev, "fdb del failed err=%d\n", err); +- dev_close(dev); ++ netdev_err(dev, ++ "failed to delete %pM vid %d from fdb: %d\n", ++ fdb_info->addr, fdb_info->vid, err); + } ++ + break; + } + rtnl_unlock(); diff --git a/target/linux/generic/backport-5.10/722-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch b/target/linux/generic/backport-5.10/722-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch new file mode 100644 index 0000000000..c1aa8fda82 --- /dev/null +++ b/target/linux/generic/backport-5.10/722-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch @@ -0,0 +1,226 @@ +From c4bb76a9a0ef87c4cc1f636defed5f12deb9f5a7 Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:32 +0200 +Subject: [PATCH] net: dsa: don't use switchdev_notifier_fdb_info in + dsa_switchdev_event_work + +Currently DSA doesn't add FDB entries on the CPU port, because it only +does so through switchdev, which is associated with a net_device, and +there are none of those for the CPU port. + +But actually FDB addresses on the CPU port have some use cases of their +own, if the switchdev operations are initiated from within the DSA +layer. There is just one problem with the existing code: it passes a +structure in dsa_switchdev_event_work which was retrieved directly from +switchdev, so it contains a net_device. We need to generalize the +contents to something that covers the CPU port as well: the "ds, port" +tuple is fine for that. + +Note that the new procedure for notifying the successful FDB offload is +inspired from the rocker model. + +Also, nothing was being done if added_by_user was false. Let's check for +that a lot earlier, and don't actually bother to schedule the worker +for nothing. + +Signed-off-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + net/dsa/dsa_priv.h | 12 +++++ + net/dsa/slave.c | 106 ++++++++++++++++++++++----------------------- + 2 files changed, 65 insertions(+), 53 deletions(-) + +--- a/net/dsa/dsa_priv.h ++++ b/net/dsa/dsa_priv.h +@@ -73,6 +73,18 @@ struct dsa_notifier_mtu_info { + int mtu; + }; + ++struct dsa_switchdev_event_work { ++ struct dsa_switch *ds; ++ int port; ++ struct work_struct work; ++ unsigned long event; ++ /* Specific for SWITCHDEV_FDB_ADD_TO_DEVICE and ++ * SWITCHDEV_FDB_DEL_TO_DEVICE ++ */ ++ unsigned char addr[ETH_ALEN]; ++ u16 vid; ++}; ++ + struct dsa_slave_priv { + /* Copy of CPU port xmit for faster access in slave transmit hot path */ + struct sk_buff * (*xmit)(struct sk_buff *skb, +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -2087,76 +2087,66 @@ static int dsa_slave_netdevice_event(str + return NOTIFY_DONE; + } + +-struct dsa_switchdev_event_work { +- struct work_struct work; +- struct switchdev_notifier_fdb_info fdb_info; +- struct net_device *dev; +- unsigned long event; +-}; ++static void ++dsa_fdb_offload_notify(struct dsa_switchdev_event_work *switchdev_work) ++{ ++ struct dsa_switch *ds = switchdev_work->ds; ++ struct switchdev_notifier_fdb_info info; ++ struct dsa_port *dp; ++ ++ if (!dsa_is_user_port(ds, switchdev_work->port)) ++ return; ++ ++ info.addr = switchdev_work->addr; ++ info.vid = switchdev_work->vid; ++ info.offloaded = true; ++ dp = dsa_to_port(ds, switchdev_work->port); ++ call_switchdev_notifiers(SWITCHDEV_FDB_OFFLOADED, ++ dp->slave, &info.info, NULL); ++} + + static void dsa_slave_switchdev_event_work(struct work_struct *work) + { + struct dsa_switchdev_event_work *switchdev_work = + container_of(work, struct dsa_switchdev_event_work, work); +- struct net_device *dev = switchdev_work->dev; +- struct switchdev_notifier_fdb_info *fdb_info; +- struct dsa_port *dp = dsa_slave_to_port(dev); ++ struct dsa_switch *ds = switchdev_work->ds; ++ struct dsa_port *dp; + int err; + ++ dp = dsa_to_port(ds, switchdev_work->port); ++ + rtnl_lock(); + switch (switchdev_work->event) { + case SWITCHDEV_FDB_ADD_TO_DEVICE: +- fdb_info = &switchdev_work->fdb_info; +- if (!fdb_info->added_by_user) +- break; +- +- err = dsa_port_fdb_add(dp, fdb_info->addr, fdb_info->vid); ++ err = dsa_port_fdb_add(dp, switchdev_work->addr, ++ switchdev_work->vid); + if (err) { +- netdev_err(dev, +- "failed to add %pM vid %d to fdb: %d\n", +- fdb_info->addr, fdb_info->vid, err); ++ dev_err(ds->dev, ++ "port %d failed to add %pM vid %d to fdb: %d\n", ++ dp->index, switchdev_work->addr, ++ switchdev_work->vid, err); + break; + } +- fdb_info->offloaded = true; +- call_switchdev_notifiers(SWITCHDEV_FDB_OFFLOADED, dev, +- &fdb_info->info, NULL); ++ dsa_fdb_offload_notify(switchdev_work); + break; + + case SWITCHDEV_FDB_DEL_TO_DEVICE: +- fdb_info = &switchdev_work->fdb_info; +- if (!fdb_info->added_by_user) +- break; +- +- err = dsa_port_fdb_del(dp, fdb_info->addr, fdb_info->vid); ++ err = dsa_port_fdb_del(dp, switchdev_work->addr, ++ switchdev_work->vid); + if (err) { +- netdev_err(dev, +- "failed to delete %pM vid %d from fdb: %d\n", +- fdb_info->addr, fdb_info->vid, err); ++ dev_err(ds->dev, ++ "port %d failed to delete %pM vid %d from fdb: %d\n", ++ dp->index, switchdev_work->addr, ++ switchdev_work->vid, err); + } + + break; + } + rtnl_unlock(); + +- kfree(switchdev_work->fdb_info.addr); + kfree(switchdev_work); +- dev_put(dev); +-} +- +-static int +-dsa_slave_switchdev_fdb_work_init(struct dsa_switchdev_event_work * +- switchdev_work, +- const struct switchdev_notifier_fdb_info * +- fdb_info) +-{ +- memcpy(&switchdev_work->fdb_info, fdb_info, +- sizeof(switchdev_work->fdb_info)); +- switchdev_work->fdb_info.addr = kzalloc(ETH_ALEN, GFP_ATOMIC); +- if (!switchdev_work->fdb_info.addr) +- return -ENOMEM; +- ether_addr_copy((u8 *)switchdev_work->fdb_info.addr, +- fdb_info->addr); +- return 0; ++ if (dsa_is_user_port(ds, dp->index)) ++ dev_put(dp->slave); + } + + /* Called under rcu_read_lock() */ +@@ -2164,7 +2154,9 @@ static int dsa_slave_switchdev_event(str + unsigned long event, void *ptr) + { + struct net_device *dev = switchdev_notifier_info_to_dev(ptr); ++ const struct switchdev_notifier_fdb_info *fdb_info; + struct dsa_switchdev_event_work *switchdev_work; ++ struct dsa_port *dp; + int err; + + if (event == SWITCHDEV_PORT_ATTR_SET) { +@@ -2177,20 +2169,32 @@ static int dsa_slave_switchdev_event(str + if (!dsa_slave_dev_check(dev)) + return NOTIFY_DONE; + ++ dp = dsa_slave_to_port(dev); ++ + switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); + if (!switchdev_work) + return NOTIFY_BAD; + + INIT_WORK(&switchdev_work->work, + dsa_slave_switchdev_event_work); +- switchdev_work->dev = dev; ++ switchdev_work->ds = dp->ds; ++ switchdev_work->port = dp->index; + switchdev_work->event = event; + + switch (event) { + case SWITCHDEV_FDB_ADD_TO_DEVICE: + case SWITCHDEV_FDB_DEL_TO_DEVICE: +- if (dsa_slave_switchdev_fdb_work_init(switchdev_work, ptr)) +- goto err_fdb_work_init; ++ fdb_info = ptr; ++ ++ if (!fdb_info->added_by_user) { ++ kfree(switchdev_work); ++ return NOTIFY_OK; ++ } ++ ++ ether_addr_copy(switchdev_work->addr, ++ fdb_info->addr); ++ switchdev_work->vid = fdb_info->vid; ++ + dev_hold(dev); + break; + default: +@@ -2200,10 +2204,6 @@ static int dsa_slave_switchdev_event(str + + dsa_schedule_work(&switchdev_work->work); + return NOTIFY_OK; +- +-err_fdb_work_init: +- kfree(switchdev_work); +- return NOTIFY_BAD; + } + + static int dsa_slave_switchdev_blocking_event(struct notifier_block *unused, diff --git a/target/linux/generic/backport-5.10/723-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch b/target/linux/generic/backport-5.10/723-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch new file mode 100644 index 0000000000..9131df70d3 --- /dev/null +++ b/target/linux/generic/backport-5.10/723-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch @@ -0,0 +1,85 @@ +From 447d290a58bd335d68f665713842365d3d6447df Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:33 +0200 +Subject: [PATCH] net: dsa: move switchdev event implementation under the same + switch/case statement + +We'll need to start listening to SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE +events even for interfaces where dsa_slave_dev_check returns false, so +we need that check inside the switch-case statement for SWITCHDEV_FDB_*. + +This movement also avoids a useless allocation / free of switchdev_work +on the untreated "default event" case. + +Signed-off-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + net/dsa/slave.c | 35 ++++++++++++++++------------------- + 1 file changed, 16 insertions(+), 19 deletions(-) + +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -2159,31 +2159,29 @@ static int dsa_slave_switchdev_event(str + struct dsa_port *dp; + int err; + +- if (event == SWITCHDEV_PORT_ATTR_SET) { ++ switch (event) { ++ case SWITCHDEV_PORT_ATTR_SET: + err = switchdev_handle_port_attr_set(dev, ptr, + dsa_slave_dev_check, + dsa_slave_port_attr_set); + return notifier_from_errno(err); +- } +- +- if (!dsa_slave_dev_check(dev)) +- return NOTIFY_DONE; ++ case SWITCHDEV_FDB_ADD_TO_DEVICE: ++ case SWITCHDEV_FDB_DEL_TO_DEVICE: ++ if (!dsa_slave_dev_check(dev)) ++ return NOTIFY_DONE; + +- dp = dsa_slave_to_port(dev); ++ dp = dsa_slave_to_port(dev); + +- switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); +- if (!switchdev_work) +- return NOTIFY_BAD; +- +- INIT_WORK(&switchdev_work->work, +- dsa_slave_switchdev_event_work); +- switchdev_work->ds = dp->ds; +- switchdev_work->port = dp->index; +- switchdev_work->event = event; ++ switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); ++ if (!switchdev_work) ++ return NOTIFY_BAD; ++ ++ INIT_WORK(&switchdev_work->work, ++ dsa_slave_switchdev_event_work); ++ switchdev_work->ds = dp->ds; ++ switchdev_work->port = dp->index; ++ switchdev_work->event = event; + +- switch (event) { +- case SWITCHDEV_FDB_ADD_TO_DEVICE: +- case SWITCHDEV_FDB_DEL_TO_DEVICE: + fdb_info = ptr; + + if (!fdb_info->added_by_user) { +@@ -2196,13 +2194,12 @@ static int dsa_slave_switchdev_event(str + switchdev_work->vid = fdb_info->vid; + + dev_hold(dev); ++ dsa_schedule_work(&switchdev_work->work); + break; + default: +- kfree(switchdev_work); + return NOTIFY_DONE; + } + +- dsa_schedule_work(&switchdev_work->work); + return NOTIFY_OK; + } + diff --git a/target/linux/generic/backport-5.10/724-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch b/target/linux/generic/backport-5.10/724-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch new file mode 100644 index 0000000000..b7b6ebe461 --- /dev/null +++ b/target/linux/generic/backport-5.10/724-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch @@ -0,0 +1,42 @@ +From 5fb4a451a87d8ed3363d28b63a3295399373d6c4 Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:34 +0200 +Subject: [PATCH] net: dsa: exit early in dsa_slave_switchdev_event if we can't + program the FDB + +Right now, the following would happen for a switch driver that does not +implement .port_fdb_add or .port_fdb_del. + +dsa_slave_switchdev_event returns NOTIFY_OK and schedules: +-> dsa_slave_switchdev_event_work + -> dsa_port_fdb_add + -> dsa_port_notify(DSA_NOTIFIER_FDB_ADD) + -> dsa_switch_fdb_add + -> if (!ds->ops->port_fdb_add) return -EOPNOTSUPP; + -> an error is printed with dev_dbg, and + dsa_fdb_offload_notify(switchdev_work) is not called. + +We can avoid scheduling the worker for nothing and say NOTIFY_DONE. +Because we don't call dsa_fdb_offload_notify, the static FDB entry will +remain just in the software bridge. + +Signed-off-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Reviewed-by: Andrew Lunn +Signed-off-by: Jakub Kicinski +--- + net/dsa/slave.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -2172,6 +2172,9 @@ static int dsa_slave_switchdev_event(str + + dp = dsa_slave_to_port(dev); + ++ if (!dp->ds->ops->port_fdb_add || !dp->ds->ops->port_fdb_del) ++ return NOTIFY_DONE; ++ + switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); + if (!switchdev_work) + return NOTIFY_BAD; diff --git a/target/linux/generic/backport-5.10/725-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch b/target/linux/generic/backport-5.10/725-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch new file mode 100644 index 0000000000..e7b9af1951 --- /dev/null +++ b/target/linux/generic/backport-5.10/725-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch @@ -0,0 +1,264 @@ +From d5f19486cee79d04c054427577ac96ed123706db Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Wed, 6 Jan 2021 11:51:35 +0200 +Subject: [PATCH] net: dsa: listen for SWITCHDEV_{FDB,DEL}_ADD_TO_DEVICE on + foreign bridge neighbors + +Some DSA switches (and not only) cannot learn source MAC addresses from +packets injected from the CPU. They only perform hardware address +learning from inbound traffic. + +This can be problematic when we have a bridge spanning some DSA switch +ports and some non-DSA ports (which we'll call "foreign interfaces" from +DSA's perspective). + +There are 2 classes of problems created by the lack of learning on +CPU-injected traffic: +- excessive flooding, due to the fact that DSA treats those addresses as + unknown +- the risk of stale routes, which can lead to temporary packet loss + +To illustrate the second class, consider the following situation, which +is common in production equipment (wireless access points, where there +is a WLAN interface and an Ethernet switch, and these form a single +bridging domain). + + AP 1: + +------------------------------------------------------------------------+ + | br0 | + +------------------------------------------------------------------------+ + +------------+ +------------+ +------------+ +------------+ +------------+ + | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | + +------------+ +------------+ +------------+ +------------+ +------------+ + | ^ ^ + | | | + | | | + | Client A Client B + | + | + | + +------------+ +------------+ +------------+ +------------+ +------------+ + | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | + +------------+ +------------+ +------------+ +------------+ +------------+ + +------------------------------------------------------------------------+ + | br0 | + +------------------------------------------------------------------------+ + AP 2 + +- br0 of AP 1 will know that Clients A and B are reachable via wlan0 +- the hardware fdb of a DSA switch driver today is not kept in sync with + the software entries on other bridge ports, so it will not know that + clients A and B are reachable via the CPU port UNLESS the hardware + switch itself performs SA learning from traffic injected from the CPU. + Nonetheless, a substantial number of switches don't. +- the hardware fdb of the DSA switch on AP 2 may autonomously learn that + Client A and B are reachable through swp0. Therefore, the software br0 + of AP 2 also may or may not learn this. In the example we're + illustrating, some Ethernet traffic has been going on, and br0 from AP + 2 has indeed learnt that it can reach Client B through swp0. + +One of the wireless clients, say Client B, disconnects from AP 1 and +roams to AP 2. The topology now looks like this: + + AP 1: + +------------------------------------------------------------------------+ + | br0 | + +------------------------------------------------------------------------+ + +------------+ +------------+ +------------+ +------------+ +------------+ + | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | + +------------+ +------------+ +------------+ +------------+ +------------+ + | ^ + | | + | Client A + | + | + | Client B + | | + | v + +------------+ +------------+ +------------+ +------------+ +------------+ + | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | + +------------+ +------------+ +------------+ +------------+ +------------+ + +------------------------------------------------------------------------+ + | br0 | + +------------------------------------------------------------------------+ + AP 2 + +- br0 of AP 1 still knows that Client A is reachable via wlan0 (no change) +- br0 of AP 1 will (possibly) know that Client B has left wlan0. There + are cases where it might never find out though. Either way, DSA today + does not process that notification in any way. +- the hardware FDB of the DSA switch on AP 1 may learn autonomously that + Client B can be reached via swp0, if it receives any packet with + Client 1's source MAC address over Ethernet. +- the hardware FDB of the DSA switch on AP 2 still thinks that Client B + can be reached via swp0. It does not know that it has roamed to wlan0, + because it doesn't perform SA learning from the CPU port. + +Now Client A contacts Client B. +AP 1 routes the packet fine towards swp0 and delivers it on the Ethernet +segment. +AP 2 sees a frame on swp0 and its fdb says that the destination is swp0. +Hairpinning is disabled => drop. + +This problem comes from the fact that these switches have a 'blind spot' +for addresses coming from software bridging. The generic solution is not +to assume that hardware learning can be enabled somehow, but to listen +to more bridge learning events. It turns out that the bridge driver does +learn in software from all inbound frames, in __br_handle_local_finish. +A proper SWITCHDEV_FDB_ADD_TO_DEVICE notification is emitted for the +addresses serviced by the bridge on 'foreign' interfaces. The software +bridge also does the right thing on migration, by notifying that the old +entry is deleted, so that does not need to be special-cased in DSA. When +it is deleted, we just need to delete our static FDB entry towards the +CPU too, and wait. + +The problem is that DSA currently only cares about SWITCHDEV_FDB_ADD_TO_DEVICE +events received on its own interfaces, such as static FDB entries. + +Luckily we can change that, and DSA can listen to all switchdev FDB +add/del events in the system and figure out if those events were emitted +by a bridge that spans at least one of DSA's own ports. In case that is +true, DSA will also offload that address towards its own CPU port, in +the eventuality that there might be bridge clients attached to the DSA +switch who want to talk to the station connected to the foreign +interface. + +In terms of implementation, we need to keep the fdb_info->added_by_user +check for the case where the switchdev event was targeted directly at a +DSA switch port. But we don't need to look at that flag for snooped +events. So the check is currently too late, we need to move it earlier. +This also simplifies the code a bit, since we avoid uselessly allocating +and freeing switchdev_work. + +We could probably do some improvements in the future. For example, +multi-bridge support is rudimentary at the moment. If there are two +bridges spanning a DSA switch's ports, and both of them need to service +the same MAC address, then what will happen is that the migration of one +of those stations will trigger the deletion of the FDB entry from the +CPU port while it is still used by other bridge. That could be improved +with reference counting but is left for another time. + +This behavior needs to be enabled at driver level by setting +ds->assisted_learning_on_cpu_port = true. This is because we don't want +to inflict a potential performance penalty (accesses through +MDIO/I2C/SPI are expensive) to hardware that really doesn't need it +because address learning on the CPU port works there. + +Reported-by: DENG Qingfang +Signed-off-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Reviewed-by: Andrew Lunn +Signed-off-by: Jakub Kicinski +--- + include/net/dsa.h | 5 +++++ + net/dsa/slave.c | 66 +++++++++++++++++++++++++++++++++++++++++++++---------- + 2 files changed, 60 insertions(+), 11 deletions(-) + +--- a/include/net/dsa.h ++++ b/include/net/dsa.h +@@ -317,6 +317,11 @@ struct dsa_switch { + */ + bool untag_bridge_pvid; + ++ /* Let DSA manage the FDB entries towards the CPU, based on the ++ * software bridge database. ++ */ ++ bool assisted_learning_on_cpu_port; ++ + /* In case vlan_filtering_is_global is set, the VLAN awareness state + * should be retrieved from here and not from the per-port settings. + */ +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -2149,6 +2149,28 @@ static void dsa_slave_switchdev_event_wo + dev_put(dp->slave); + } + ++static int dsa_lower_dev_walk(struct net_device *lower_dev, ++ struct netdev_nested_priv *priv) ++{ ++ if (dsa_slave_dev_check(lower_dev)) { ++ priv->data = (void *)netdev_priv(lower_dev); ++ return 1; ++ } ++ ++ return 0; ++} ++ ++static struct dsa_slave_priv *dsa_slave_dev_lower_find(struct net_device *dev) ++{ ++ struct netdev_nested_priv priv = { ++ .data = NULL, ++ }; ++ ++ netdev_walk_all_lower_dev_rcu(dev, dsa_lower_dev_walk, &priv); ++ ++ return (struct dsa_slave_priv *)priv.data; ++} ++ + /* Called under rcu_read_lock() */ + static int dsa_slave_switchdev_event(struct notifier_block *unused, + unsigned long event, void *ptr) +@@ -2167,10 +2189,37 @@ static int dsa_slave_switchdev_event(str + return notifier_from_errno(err); + case SWITCHDEV_FDB_ADD_TO_DEVICE: + case SWITCHDEV_FDB_DEL_TO_DEVICE: +- if (!dsa_slave_dev_check(dev)) +- return NOTIFY_DONE; ++ fdb_info = ptr; ++ ++ if (dsa_slave_dev_check(dev)) { ++ if (!fdb_info->added_by_user) ++ return NOTIFY_OK; ++ ++ dp = dsa_slave_to_port(dev); ++ } else { ++ /* Snoop addresses learnt on foreign interfaces ++ * bridged with us, for switches that don't ++ * automatically learn SA from CPU-injected traffic ++ */ ++ struct net_device *br_dev; ++ struct dsa_slave_priv *p; ++ ++ br_dev = netdev_master_upper_dev_get_rcu(dev); ++ if (!br_dev) ++ return NOTIFY_DONE; ++ ++ if (!netif_is_bridge_master(br_dev)) ++ return NOTIFY_DONE; ++ ++ p = dsa_slave_dev_lower_find(br_dev); ++ if (!p) ++ return NOTIFY_DONE; + +- dp = dsa_slave_to_port(dev); ++ dp = p->dp->cpu_dp; ++ ++ if (!dp->ds->assisted_learning_on_cpu_port) ++ return NOTIFY_DONE; ++ } + + if (!dp->ds->ops->port_fdb_add || !dp->ds->ops->port_fdb_del) + return NOTIFY_DONE; +@@ -2185,18 +2234,13 @@ static int dsa_slave_switchdev_event(str + switchdev_work->port = dp->index; + switchdev_work->event = event; + +- fdb_info = ptr; +- +- if (!fdb_info->added_by_user) { +- kfree(switchdev_work); +- return NOTIFY_OK; +- } +- + ether_addr_copy(switchdev_work->addr, + fdb_info->addr); + switchdev_work->vid = fdb_info->vid; + +- dev_hold(dev); ++ /* Hold a reference on the slave for dsa_fdb_offload_notify */ ++ if (dsa_is_user_port(dp->ds, dp->index)) ++ dev_hold(dev); + dsa_schedule_work(&switchdev_work->work); + break; + default: diff --git a/target/linux/generic/backport-5.10/730-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch b/target/linux/generic/backport-5.10/730-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch new file mode 100644 index 0000000000..f3a6f948ad --- /dev/null +++ b/target/linux/generic/backport-5.10/730-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch @@ -0,0 +1,84 @@ +From c3b8e07909dbe67b0d580416c1a5257643a73be7 Mon Sep 17 00:00:00 2001 +From: Ilya Lipnitskiy +Date: Fri, 12 Mar 2021 00:07:03 -0800 +Subject: [PATCH] net: dsa: mt7530: setup core clock even in TRGMII mode + +A recent change to MIPS ralink reset logic made it so mt7530 actually +resets the switch on platforms such as mt7621 (where bit 2 is the reset +line for the switch). That exposed an issue where the switch would not +function properly in TRGMII mode after a reset. + +Reconfigure core clock in TRGMII mode to fix the issue. + +Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled. + +Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines") +Signed-off-by: Ilya Lipnitskiy +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 52 +++++++++++++++++++--------------------- + 1 file changed, 25 insertions(+), 27 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch * + TD_DM_DRVP(8) | TD_DM_DRVN(8)); + + /* Setup core clock for MT7530 */ +- if (!trgint) { +- /* Disable MT7530 core clock */ +- core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); +- +- /* Disable PLL, since phy_device has not yet been created +- * provided for phy_[read,write]_mmd_indirect is called, we +- * provide our own core_write_mmd_indirect to complete this +- * function. +- */ +- core_write_mmd_indirect(priv, +- CORE_GSWPLL_GRP1, +- MDIO_MMD_VEND2, +- 0); +- +- /* Set core clock into 500Mhz */ +- core_write(priv, CORE_GSWPLL_GRP2, +- RG_GSWPLL_POSDIV_500M(1) | +- RG_GSWPLL_FBKDIV_500M(25)); +- +- /* Enable PLL */ +- core_write(priv, CORE_GSWPLL_GRP1, +- RG_GSWPLL_EN_PRE | +- RG_GSWPLL_POSDIV_200M(2) | +- RG_GSWPLL_FBKDIV_200M(32)); +- +- /* Enable MT7530 core clock */ +- core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); +- } ++ /* Disable MT7530 core clock */ ++ core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); ++ ++ /* Disable PLL, since phy_device has not yet been created ++ * provided for phy_[read,write]_mmd_indirect is called, we ++ * provide our own core_write_mmd_indirect to complete this ++ * function. ++ */ ++ core_write_mmd_indirect(priv, ++ CORE_GSWPLL_GRP1, ++ MDIO_MMD_VEND2, ++ 0); ++ ++ /* Set core clock into 500Mhz */ ++ core_write(priv, CORE_GSWPLL_GRP2, ++ RG_GSWPLL_POSDIV_500M(1) | ++ RG_GSWPLL_FBKDIV_500M(25)); ++ ++ /* Enable PLL */ ++ core_write(priv, CORE_GSWPLL_GRP1, ++ RG_GSWPLL_EN_PRE | ++ RG_GSWPLL_POSDIV_200M(2) | ++ RG_GSWPLL_FBKDIV_200M(32)); ++ ++ /* Enable MT7530 core clock */ ++ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); + + /* Setup the MT7530 TRGMII Tx Clock */ + core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); diff --git a/target/linux/generic/backport-5.10/730-net-phy-at803x-select-correct-page-on-config-init.patch b/target/linux/generic/backport-5.10/730-net-phy-at803x-select-correct-page-on-config-init.patch deleted file mode 100644 index 00be403299..0000000000 --- a/target/linux/generic/backport-5.10/730-net-phy-at803x-select-correct-page-on-config-init.patch +++ /dev/null @@ -1,108 +0,0 @@ -From c329e5afb42ff0a88285eb4d8a391a18793e4777 Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Thu, 15 Apr 2021 03:26:50 +0200 -Subject: [PATCH] net: phy: at803x: select correct page on config init - -The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber -as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit -in the chip configure register. - -The driver assumes the copper side is selected on probe, but this might -not be the case depending which page was last selected by the -bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior. - -Select the copper page when probing to circumvent this. - -Signed-off-by: David Bauer -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 50 +++++++++++++++++++++++++++++++++++++++- - 1 file changed, 49 insertions(+), 1 deletion(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -139,6 +139,9 @@ - #define ATH8035_PHY_ID 0x004dd072 - #define AT8030_PHY_ID_MASK 0xffffffef - -+#define AT803X_PAGE_FIBER 0 -+#define AT803X_PAGE_COPPER 1 -+ - MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); - MODULE_AUTHOR("Matus Ujhelyi"); - MODULE_LICENSE("GPL"); -@@ -190,6 +193,35 @@ static int at803x_debug_reg_mask(struct - return phy_write(phydev, AT803X_DEBUG_DATA, val); - } - -+static int at803x_write_page(struct phy_device *phydev, int page) -+{ -+ int mask; -+ int set; -+ -+ if (page == AT803X_PAGE_COPPER) { -+ set = AT803X_BT_BX_REG_SEL; -+ mask = 0; -+ } else { -+ set = 0; -+ mask = AT803X_BT_BX_REG_SEL; -+ } -+ -+ return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); -+} -+ -+static int at803x_read_page(struct phy_device *phydev) -+{ -+ int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); -+ -+ if (ccr < 0) -+ return ccr; -+ -+ if (ccr & AT803X_BT_BX_REG_SEL) -+ return AT803X_PAGE_COPPER; -+ -+ return AT803X_PAGE_FIBER; -+} -+ - static int at803x_enable_rx_delay(struct phy_device *phydev) - { - return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, -@@ -508,6 +540,7 @@ static int at803x_probe(struct phy_devic - { - struct device *dev = &phydev->mdio.dev; - struct at803x_priv *priv; -+ int ret; - - priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); - if (!priv) -@@ -515,7 +548,20 @@ static int at803x_probe(struct phy_devic - - phydev->priv = priv; - -- return at803x_parse_dt(phydev); -+ ret = at803x_parse_dt(phydev); -+ if (ret) -+ return ret; -+ -+ /* Some bootloaders leave the fiber page selected. -+ * Switch to the copper page, as otherwise we read -+ * the PHY capabilities from the fiber side. -+ */ -+ if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { -+ ret = phy_select_page(phydev, AT803X_PAGE_COPPER); -+ ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); -+ } -+ -+ return ret; - } - - static void at803x_remove(struct phy_device *phydev) -@@ -1097,6 +1143,8 @@ static struct phy_driver at803x_driver[] - .get_wol = at803x_get_wol, - .suspend = at803x_suspend, - .resume = at803x_resume, -+ .read_page = at803x_read_page, -+ .write_page = at803x_write_page, - /* PHY_GBIT_FEATURES */ - .read_status = at803x_read_status, - .aneg_done = at803x_aneg_done, diff --git a/target/linux/generic/backport-5.10/731-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch b/target/linux/generic/backport-5.10/731-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch deleted file mode 100644 index d6ec7450e8..0000000000 --- a/target/linux/generic/backport-5.10/731-net-phy-at803x-fix-probe-error-if-copper-page-is-sel.patch +++ /dev/null @@ -1,73 +0,0 @@ -From 8f7e876273e294b732b42af2e5e6bba91d798954 Mon Sep 17 00:00:00 2001 -From: Michael Walle -Date: Tue, 20 Apr 2021 12:29:29 +0200 -Subject: [PATCH] net: phy: at803x: fix probe error if copper page is selected - -The commit c329e5afb42f ("net: phy: at803x: select correct page on -config init") selects the copper page during probe. This fails if the -copper page was already selected. In this case, the value of the copper -page (which is 1) is propagated through phy_restore_page() and is -finally returned for at803x_probe(). Fix it, by just using the -at803x_page_write() directly. - -Also in case of an error, the regulator is not disabled and leads to a -WARN_ON() when the probe fails. This couldn't happen before, because -at803x_parse_dt() was the last call in at803x_probe(). It is hard to -see, that the parse_dt() actually enables the regulator. Thus move the -regulator_enable() to the probe function and undo it in case of an -error. - -Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init") -Signed-off-by: Michael Walle -Reviewed-by: David Bauer -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 23 +++++++++++++++++------ - 1 file changed, 17 insertions(+), 6 deletions(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -527,10 +527,6 @@ static int at803x_parse_dt(struct phy_de - phydev_err(phydev, "failed to get VDDIO regulator\n"); - return PTR_ERR(priv->vddio); - } -- -- ret = regulator_enable(priv->vddio); -- if (ret < 0) -- return ret; - } - - return 0; -@@ -552,15 +548,30 @@ static int at803x_probe(struct phy_devic - if (ret) - return ret; - -+ if (priv->vddio) { -+ ret = regulator_enable(priv->vddio); -+ if (ret < 0) -+ return ret; -+ } -+ - /* Some bootloaders leave the fiber page selected. - * Switch to the copper page, as otherwise we read - * the PHY capabilities from the fiber side. - */ - if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) { -- ret = phy_select_page(phydev, AT803X_PAGE_COPPER); -- ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret); -+ phy_lock_mdio_bus(phydev); -+ ret = at803x_write_page(phydev, AT803X_PAGE_COPPER); -+ phy_unlock_mdio_bus(phydev); -+ if (ret) -+ goto err; - } - -+ return 0; -+ -+err: -+ if (priv->vddio) -+ regulator_disable(priv->vddio); -+ - return ret; - } - diff --git a/target/linux/generic/backport-5.10/731-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch b/target/linux/generic/backport-5.10/731-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch new file mode 100644 index 0000000000..9e5047a16b --- /dev/null +++ b/target/linux/generic/backport-5.10/731-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch @@ -0,0 +1,181 @@ +From 429a0edeefd88cbfca5c417dfb8561047bb50769 Mon Sep 17 00:00:00 2001 +From: DENG Qingfang +Date: Mon, 25 Jan 2021 12:43:22 +0800 +Subject: [PATCH] net: dsa: mt7530: MT7530 optional GPIO support + +MT7530's LED controller can drive up to 15 LED/GPIOs. + +Add support for GPIO control and allow users to use its GPIOs by +setting gpio-controller property in device tree. + +Signed-off-by: DENG Qingfang +Reviewed-by: Linus Walleij +Reviewed-by: Andrew Lunn +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/mt7530.c | 110 +++++++++++++++++++++++++++++++++++++++ + drivers/net/dsa/mt7530.h | 20 +++++++ + 2 files changed, 130 insertions(+) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -18,6 +18,7 @@ + #include + #include + #include ++#include + #include + + #include "mt7530.h" +@@ -1534,6 +1535,109 @@ mtk_get_tag_protocol(struct dsa_switch * + } + } + ++static inline u32 ++mt7530_gpio_to_bit(unsigned int offset) ++{ ++ /* Map GPIO offset to register bit ++ * [ 2: 0] port 0 LED 0..2 as GPIO 0..2 ++ * [ 6: 4] port 1 LED 0..2 as GPIO 3..5 ++ * [10: 8] port 2 LED 0..2 as GPIO 6..8 ++ * [14:12] port 3 LED 0..2 as GPIO 9..11 ++ * [18:16] port 4 LED 0..2 as GPIO 12..14 ++ */ ++ return BIT(offset + offset / 3); ++} ++ ++static int ++mt7530_gpio_get(struct gpio_chip *gc, unsigned int offset) ++{ ++ struct mt7530_priv *priv = gpiochip_get_data(gc); ++ u32 bit = mt7530_gpio_to_bit(offset); ++ ++ return !!(mt7530_read(priv, MT7530_LED_GPIO_DATA) & bit); ++} ++ ++static void ++mt7530_gpio_set(struct gpio_chip *gc, unsigned int offset, int value) ++{ ++ struct mt7530_priv *priv = gpiochip_get_data(gc); ++ u32 bit = mt7530_gpio_to_bit(offset); ++ ++ if (value) ++ mt7530_set(priv, MT7530_LED_GPIO_DATA, bit); ++ else ++ mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit); ++} ++ ++static int ++mt7530_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) ++{ ++ struct mt7530_priv *priv = gpiochip_get_data(gc); ++ u32 bit = mt7530_gpio_to_bit(offset); ++ ++ return (mt7530_read(priv, MT7530_LED_GPIO_DIR) & bit) ? ++ GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN; ++} ++ ++static int ++mt7530_gpio_direction_input(struct gpio_chip *gc, unsigned int offset) ++{ ++ struct mt7530_priv *priv = gpiochip_get_data(gc); ++ u32 bit = mt7530_gpio_to_bit(offset); ++ ++ mt7530_clear(priv, MT7530_LED_GPIO_OE, bit); ++ mt7530_clear(priv, MT7530_LED_GPIO_DIR, bit); ++ ++ return 0; ++} ++ ++static int ++mt7530_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value) ++{ ++ struct mt7530_priv *priv = gpiochip_get_data(gc); ++ u32 bit = mt7530_gpio_to_bit(offset); ++ ++ mt7530_set(priv, MT7530_LED_GPIO_DIR, bit); ++ ++ if (value) ++ mt7530_set(priv, MT7530_LED_GPIO_DATA, bit); ++ else ++ mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit); ++ ++ mt7530_set(priv, MT7530_LED_GPIO_OE, bit); ++ ++ return 0; ++} ++ ++static int ++mt7530_setup_gpio(struct mt7530_priv *priv) ++{ ++ struct device *dev = priv->dev; ++ struct gpio_chip *gc; ++ ++ gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL); ++ if (!gc) ++ return -ENOMEM; ++ ++ mt7530_write(priv, MT7530_LED_GPIO_OE, 0); ++ mt7530_write(priv, MT7530_LED_GPIO_DIR, 0); ++ mt7530_write(priv, MT7530_LED_IO_MODE, 0); ++ ++ gc->label = "mt7530"; ++ gc->parent = dev; ++ gc->owner = THIS_MODULE; ++ gc->get_direction = mt7530_gpio_get_direction; ++ gc->direction_input = mt7530_gpio_direction_input; ++ gc->direction_output = mt7530_gpio_direction_output; ++ gc->get = mt7530_gpio_get; ++ gc->set = mt7530_gpio_set; ++ gc->base = -1; ++ gc->ngpio = 15; ++ gc->can_sleep = true; ++ ++ return devm_gpiochip_add_data(dev, gc, priv); ++} ++ + static int + mt7530_setup(struct dsa_switch *ds) + { +@@ -1675,6 +1779,12 @@ mt7530_setup(struct dsa_switch *ds) + } + } + ++ if (of_property_read_bool(priv->dev->of_node, "gpio-controller")) { ++ ret = mt7530_setup_gpio(priv); ++ if (ret) ++ return ret; ++ } ++ + mt7530_setup_port5(ds, interface); + + /* Flush the FDB table */ +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -529,6 +529,26 @@ enum mt7531_clk_skew { + #define MT7531_GPIO12_RG_RXD3_MASK GENMASK(19, 16) + #define MT7531_EXT_P_MDIO_12 (2 << 16) + ++/* Registers for LED GPIO control (MT7530 only) ++ * All registers follow this pattern: ++ * [ 2: 0] port 0 ++ * [ 6: 4] port 1 ++ * [10: 8] port 2 ++ * [14:12] port 3 ++ * [18:16] port 4 ++ */ ++ ++/* LED enable, 0: Disable, 1: Enable (Default) */ ++#define MT7530_LED_EN 0x7d00 ++/* LED mode, 0: GPIO mode, 1: PHY mode (Default) */ ++#define MT7530_LED_IO_MODE 0x7d04 ++/* GPIO direction, 0: Input, 1: Output */ ++#define MT7530_LED_GPIO_DIR 0x7d10 ++/* GPIO output enable, 0: Disable, 1: Enable */ ++#define MT7530_LED_GPIO_OE 0x7d14 ++/* GPIO value, 0: Low, 1: High */ ++#define MT7530_LED_GPIO_DATA 0x7d18 ++ + #define MT7530_CREV 0x7ffc + #define CHIP_NAME_SHIFT 16 + #define MT7530_ID 0x7530 diff --git a/target/linux/generic/backport-5.10/731-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch b/target/linux/generic/backport-5.10/731-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch new file mode 100644 index 0000000000..38dd8a7296 --- /dev/null +++ b/target/linux/generic/backport-5.10/731-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch @@ -0,0 +1,120 @@ +From 40b5d2f15c091fa9c854acde91ad2acb504027d7 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Ren=C3=A9=20van=20Dorst?= +Date: Mon, 12 Apr 2021 08:50:31 +0200 +Subject: [PATCH] net: dsa: mt7530: Add support for EEE features +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This patch adds EEE support. + +Signed-off-by: René van Dorst +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 43 ++++++++++++++++++++++++++++++++++++++++ + drivers/net/dsa/mt7530.h | 14 ++++++++++++- + 2 files changed, 56 insertions(+), 1 deletion(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -2371,6 +2371,17 @@ static void mt753x_phylink_mac_link_up(s + mcr |= PMCR_RX_FC_EN; + } + ++ if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, 0) >= 0) { ++ switch (speed) { ++ case SPEED_1000: ++ mcr |= PMCR_FORCE_EEE1G; ++ break; ++ case SPEED_100: ++ mcr |= PMCR_FORCE_EEE100; ++ break; ++ } ++ } ++ + mt7530_set(priv, MT7530_PMCR_P(port), mcr); + } + +@@ -2601,6 +2612,36 @@ mt753x_phy_write(struct dsa_switch *ds, + return priv->info->phy_write(ds, port, regnum, val); + } + ++static int mt753x_get_mac_eee(struct dsa_switch *ds, int port, ++ struct ethtool_eee *e) ++{ ++ struct mt7530_priv *priv = ds->priv; ++ u32 eeecr = mt7530_read(priv, MT7530_PMEEECR_P(port)); ++ ++ e->tx_lpi_enabled = !(eeecr & LPI_MODE_EN); ++ e->tx_lpi_timer = GET_LPI_THRESH(eeecr); ++ ++ return 0; ++} ++ ++static int mt753x_set_mac_eee(struct dsa_switch *ds, int port, ++ struct ethtool_eee *e) ++{ ++ struct mt7530_priv *priv = ds->priv; ++ u32 set, mask = LPI_THRESH_MASK | LPI_MODE_EN; ++ ++ if (e->tx_lpi_timer > 0xFFF) ++ return -EINVAL; ++ ++ set = SET_LPI_THRESH(e->tx_lpi_timer); ++ if (!e->tx_lpi_enabled) ++ /* Force LPI Mode without a delay */ ++ set |= LPI_MODE_EN; ++ mt7530_rmw(priv, MT7530_PMEEECR_P(port), mask, set); ++ ++ return 0; ++} ++ + static const struct dsa_switch_ops mt7530_switch_ops = { + .get_tag_protocol = mtk_get_tag_protocol, + .setup = mt753x_setup, +@@ -2629,6 +2670,8 @@ static const struct dsa_switch_ops mt753 + .phylink_mac_an_restart = mt753x_phylink_mac_an_restart, + .phylink_mac_link_down = mt753x_phylink_mac_link_down, + .phylink_mac_link_up = mt753x_phylink_mac_link_up, ++ .get_mac_eee = mt753x_get_mac_eee, ++ .set_mac_eee = mt753x_set_mac_eee, + }; + + static const struct mt753x_info mt753x_table[] = { +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -240,6 +240,8 @@ enum mt7530_vlan_port_attr { + #define PMCR_RX_EN BIT(13) + #define PMCR_BACKOFF_EN BIT(9) + #define PMCR_BACKPR_EN BIT(8) ++#define PMCR_FORCE_EEE1G BIT(7) ++#define PMCR_FORCE_EEE100 BIT(6) + #define PMCR_TX_FC_EN BIT(5) + #define PMCR_RX_FC_EN BIT(4) + #define PMCR_FORCE_SPEED_1000 BIT(3) +@@ -264,7 +266,8 @@ enum mt7530_vlan_port_attr { + #define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \ + PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \ + PMCR_TX_FC_EN | PMCR_RX_FC_EN | \ +- PMCR_FORCE_FDX | PMCR_FORCE_LNK) ++ PMCR_FORCE_FDX | PMCR_FORCE_LNK | \ ++ PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100) + #define PMCR_CPU_PORT_SETTING(id) (PMCR_FORCE_MODE_ID((id)) | \ + PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \ + PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \ +@@ -273,6 +276,15 @@ enum mt7530_vlan_port_attr { + PMCR_FORCE_SPEED_1000 | \ + PMCR_FORCE_FDX | PMCR_FORCE_LNK) + ++#define MT7530_PMEEECR_P(x) (0x3004 + (x) * 0x100) ++#define WAKEUP_TIME_1000(x) (((x) & 0xFF) << 24) ++#define WAKEUP_TIME_100(x) (((x) & 0xFF) << 16) ++#define LPI_THRESH_MASK GENMASK(15, 4) ++#define LPI_THRESH_SHT 4 ++#define SET_LPI_THRESH(x) (((x) << LPI_THRESH_SHT) & LPI_THRESH_MASK) ++#define GET_LPI_THRESH(x) (((x) & LPI_THRESH_MASK) >> LPI_THRESH_SHT) ++#define LPI_MODE_EN BIT(0) ++ + #define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100) + #define PMSR_EEE1G BIT(7) + #define PMSR_EEE100M BIT(6) diff --git a/target/linux/generic/backport-5.10/732-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch b/target/linux/generic/backport-5.10/732-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch new file mode 100644 index 0000000000..8e242bfffc --- /dev/null +++ b/target/linux/generic/backport-5.10/732-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch @@ -0,0 +1,1935 @@ +From 83216e3988cd196183542937c9bd58b279f946af Mon Sep 17 00:00:00 2001 +From: Michael Walle +Date: Mon, 12 Apr 2021 19:47:17 +0200 +Subject: of: net: pass the dst buffer to of_get_mac_address() + +of_get_mac_address() returns a "const void*" pointer to a MAC address. +Lately, support to fetch the MAC address by an NVMEM provider was added. +But this will only work with platform devices. It will not work with +PCI devices (e.g. of an integrated root complex) and esp. not with DSA +ports. + +There is an of_* variant of the nvmem binding which works without +devices. The returned data of a nvmem_cell_read() has to be freed after +use. On the other hand the return of_get_mac_address() points to some +static data without a lifetime. The trick for now, was to allocate a +device resource managed buffer which is then returned. This will only +work if we have an actual device. + +Change it, so that the caller of of_get_mac_address() has to supply a +buffer where the MAC address is written to. Unfortunately, this will +touch all drivers which use the of_get_mac_address(). + +Usually the code looks like: + + const char *addr; + addr = of_get_mac_address(np); + if (!IS_ERR(addr)) + ether_addr_copy(ndev->dev_addr, addr); + +This can then be simply rewritten as: + + of_get_mac_address(np, ndev->dev_addr); + +Sometimes is_valid_ether_addr() is used to test the MAC address. +of_get_mac_address() already makes sure, it just returns a valid MAC +address. Thus we can just test its return code. But we have to be +careful if there are still other sources for the MAC address before the +of_get_mac_address(). In this case we have to keep the +is_valid_ether_addr() call. + +The following coccinelle patch was used to convert common cases to the +new style. Afterwards, I've manually gone over the drivers and fixed the +return code variable: either used a new one or if one was already +available use that. Mansour Moufid, thanks for that coccinelle patch! + + +@a@ +identifier x; +expression y, z; +@@ +- x = of_get_mac_address(y); ++ x = of_get_mac_address(y, z); + <... +- ether_addr_copy(z, x); + ...> + +@@ +identifier a.x; +@@ +- if (<+... x ...+>) {} + +@@ +identifier a.x; +@@ + if (<+... x ...+>) { + ... + } +- else {} + +@@ +identifier a.x; +expression e; +@@ +- if (<+... x ...+>@e) +- {} +- else ++ if (!(e)) + {...} + +@@ +expression x, y, z; +@@ +- x = of_get_mac_address(y, z); ++ of_get_mac_address(y, z); + ... when != x + + +All drivers, except drivers/net/ethernet/aeroflex/greth.c, were +compile-time tested. + +Suggested-by: Andrew Lunn +Signed-off-by: Michael Walle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + arch/arm/mach-mvebu/kirkwood.c | 3 +- + arch/powerpc/sysdev/tsi108_dev.c | 5 +- + drivers/net/ethernet/aeroflex/greth.c | 6 +-- + drivers/net/ethernet/allwinner/sun4i-emac.c | 10 ++-- + drivers/net/ethernet/altera/altera_tse_main.c | 7 +-- + drivers/net/ethernet/arc/emac_main.c | 8 +-- + drivers/net/ethernet/atheros/ag71xx.c | 7 +-- + drivers/net/ethernet/broadcom/bcm4908_enet.c | 7 +-- + drivers/net/ethernet/broadcom/bcmsysport.c | 7 +-- + drivers/net/ethernet/broadcom/bgmac-bcma.c | 10 ++-- + drivers/net/ethernet/broadcom/bgmac-platform.c | 11 ++-- + drivers/net/ethernet/cadence/macb_main.c | 11 ++-- + drivers/net/ethernet/cavium/octeon/octeon_mgmt.c | 8 +-- + drivers/net/ethernet/cavium/thunder/thunder_bgx.c | 5 +- + drivers/net/ethernet/davicom/dm9000.c | 10 ++-- + drivers/net/ethernet/ethoc.c | 6 +-- + drivers/net/ethernet/ezchip/nps_enet.c | 7 +-- + drivers/net/ethernet/freescale/fec_main.c | 7 +-- + drivers/net/ethernet/freescale/fec_mpc52xx.c | 7 +-- + drivers/net/ethernet/freescale/fman/mac.c | 9 ++-- + .../net/ethernet/freescale/fs_enet/fs_enet-main.c | 5 +- + drivers/net/ethernet/freescale/gianfar.c | 8 +-- + drivers/net/ethernet/freescale/ucc_geth.c | 5 +- + drivers/net/ethernet/hisilicon/hisi_femac.c | 7 +-- + drivers/net/ethernet/hisilicon/hix5hd2_gmac.c | 7 +-- + drivers/net/ethernet/lantiq_xrx200.c | 7 +-- + drivers/net/ethernet/marvell/mv643xx_eth.c | 5 +- + drivers/net/ethernet/marvell/mvneta.c | 6 +-- + .../net/ethernet/marvell/prestera/prestera_main.c | 11 ++-- + drivers/net/ethernet/marvell/pxa168_eth.c | 9 +--- + drivers/net/ethernet/marvell/sky2.c | 8 ++- + drivers/net/ethernet/mediatek/mtk_eth_soc.c | 11 ++-- + drivers/net/ethernet/micrel/ks8851_common.c | 7 ++- + drivers/net/ethernet/microchip/lan743x_main.c | 5 +- + drivers/net/ethernet/nxp/lpc_eth.c | 4 +- + drivers/net/ethernet/qualcomm/qca_spi.c | 10 ++-- + drivers/net/ethernet/qualcomm/qca_uart.c | 9 +--- + drivers/net/ethernet/renesas/ravb_main.c | 12 +++-- + drivers/net/ethernet/renesas/sh_eth.c | 5 +- + .../net/ethernet/samsung/sxgbe/sxgbe_platform.c | 13 ++--- + drivers/net/ethernet/socionext/sni_ave.c | 10 ++-- + .../net/ethernet/stmicro/stmmac/dwmac-anarion.c | 2 +- + .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-generic.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-intel-plat.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 2 +- + .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c | 2 +- + .../net/ethernet/stmicro/stmmac/dwmac-visconti.c | 2 +- + drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 +- + drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- + .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 14 ++--- + .../net/ethernet/stmicro/stmmac/stmmac_platform.h | 2 +- + drivers/net/ethernet/ti/am65-cpsw-nuss.c | 19 ++++--- + drivers/net/ethernet/ti/cpsw.c | 7 +-- + drivers/net/ethernet/ti/cpsw_new.c | 7 +-- + drivers/net/ethernet/ti/davinci_emac.c | 8 +-- + drivers/net/ethernet/ti/netcp_core.c | 7 +-- + drivers/net/ethernet/wiznet/w5100-spi.c | 8 ++- + drivers/net/ethernet/wiznet/w5100.c | 2 +- + drivers/net/ethernet/xilinx/ll_temac_main.c | 8 +-- + drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 15 +++--- + drivers/net/ethernet/xilinx/xilinx_emaclite.c | 8 +-- + drivers/net/wireless/ath/ath9k/init.c | 5 +- + drivers/net/wireless/mediatek/mt76/eeprom.c | 9 +--- + drivers/net/wireless/ralink/rt2x00/rt2x00dev.c | 6 +-- + drivers/of/of_net.c | 60 ++++++++++------------ + drivers/staging/octeon/ethernet.c | 10 ++-- + drivers/staging/wfx/main.c | 7 ++- + include/linux/of_net.h | 6 +-- + include/net/dsa.h | 2 +- + net/dsa/dsa2.c | 2 +- + net/dsa/slave.c | 2 +- + net/ethernet/eth.c | 11 ++-- + 85 files changed, 218 insertions(+), 364 deletions(-) + +--- a/arch/arm/mach-mvebu/kirkwood.c ++++ b/arch/arm/mach-mvebu/kirkwood.c +@@ -84,6 +84,7 @@ static void __init kirkwood_dt_eth_fixup + struct device_node *pnp = of_get_parent(np); + struct clk *clk; + struct property *pmac; ++ u8 tmpmac[ETH_ALEN]; + void __iomem *io; + u8 *macaddr; + u32 reg; +@@ -93,7 +94,7 @@ static void __init kirkwood_dt_eth_fixup + + /* skip disabled nodes or nodes with valid MAC address*/ + if (!of_device_is_available(pnp) || +- !IS_ERR(of_get_mac_address(np))) ++ !of_get_mac_address(np, tmpmac)) + goto eth_fixup_skip; + + clk = of_clk_get(pnp, 0); +--- a/arch/powerpc/sysdev/tsi108_dev.c ++++ b/arch/powerpc/sysdev/tsi108_dev.c +@@ -73,7 +73,6 @@ static int __init tsi108_eth_of_init(voi + struct device_node *phy, *mdio; + hw_info tsi_eth_data; + const unsigned int *phy_id; +- const void *mac_addr; + const phandle *ph; + + memset(r, 0, sizeof(r)); +@@ -101,9 +100,7 @@ static int __init tsi108_eth_of_init(voi + goto err; + } + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(tsi_eth_data.mac_addr, mac_addr); ++ of_get_mac_address(np, tsi_eth_data.mac_addr); + + ph = of_get_property(np, "mdio-handle", NULL); + mdio = of_find_node_by_phandle(*ph); +--- a/drivers/net/ethernet/aeroflex/greth.c ++++ b/drivers/net/ethernet/aeroflex/greth.c +@@ -1449,10 +1449,10 @@ static int greth_of_probe(struct platfor + break; + } + if (i == 6) { +- const u8 *addr; ++ u8 addr[ETH_ALEN]; + +- addr = of_get_mac_address(ofdev->dev.of_node); +- if (!IS_ERR(addr)) { ++ err = of_get_mac_address(ofdev->dev.of_node, addr); ++ if (!err) { + for (i = 0; i < 6; i++) + macaddr[i] = (unsigned int) addr[i]; + } else { +--- a/drivers/net/ethernet/allwinner/sun4i-emac.c ++++ b/drivers/net/ethernet/allwinner/sun4i-emac.c +@@ -790,7 +790,6 @@ static int emac_probe(struct platform_de + struct emac_board_info *db; + struct net_device *ndev; + int ret = 0; +- const char *mac_addr; + + ndev = alloc_etherdev(sizeof(struct emac_board_info)); + if (!ndev) { +@@ -853,12 +852,9 @@ static int emac_probe(struct platform_de + } + + /* Read MAC-address from DT */ +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- +- /* Check if the MAC address is valid, if not get a random one */ +- if (!is_valid_ether_addr(ndev->dev_addr)) { ++ ret = of_get_mac_address(np, ndev->dev_addr); ++ if (ret) { ++ /* if the MAC address is invalid get a random one */ + eth_hw_addr_random(ndev); + dev_warn(&pdev->dev, "using random MAC address %pM\n", + ndev->dev_addr); +--- a/drivers/net/ethernet/altera/altera_tse_main.c ++++ b/drivers/net/ethernet/altera/altera_tse_main.c +@@ -1351,7 +1351,6 @@ static int altera_tse_probe(struct platf + struct resource *control_port; + struct resource *dma_res; + struct altera_tse_private *priv; +- const unsigned char *macaddr; + void __iomem *descmap; + const struct of_device_id *of_id = NULL; + +@@ -1525,10 +1524,8 @@ static int altera_tse_probe(struct platf + priv->rx_dma_buf_sz = ALTERA_RXDMABUFFER_SIZE; + + /* get default MAC address from device tree */ +- macaddr = of_get_mac_address(pdev->dev.of_node); +- if (!IS_ERR(macaddr)) +- ether_addr_copy(ndev->dev_addr, macaddr); +- else ++ ret = of_get_mac_address(pdev->dev.of_node, ndev->dev_addr); ++ if (ret) + eth_hw_addr_random(ndev); + + /* get phy addr and create mdio */ +--- a/drivers/net/ethernet/arc/emac_main.c ++++ b/drivers/net/ethernet/arc/emac_main.c +@@ -857,7 +857,6 @@ int arc_emac_probe(struct net_device *nd + struct device_node *phy_node; + struct phy_device *phydev = NULL; + struct arc_emac_priv *priv; +- const char *mac_addr; + unsigned int id, clock_frequency, irq; + int err; + +@@ -942,11 +941,8 @@ int arc_emac_probe(struct net_device *nd + } + + /* Get MAC address from device tree */ +- mac_addr = of_get_mac_address(dev->of_node); +- +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- else ++ err = of_get_mac_address(dev->of_node, ndev->dev_addr); ++ if (err) + eth_hw_addr_random(ndev); + + arc_emac_set_address_internal(ndev); +--- a/drivers/net/ethernet/atheros/ag71xx.c ++++ b/drivers/net/ethernet/atheros/ag71xx.c +@@ -1856,7 +1856,6 @@ static int ag71xx_probe(struct platform_ + const struct ag71xx_dcfg *dcfg; + struct net_device *ndev; + struct resource *res; +- const void *mac_addr; + int tx_size, err, i; + struct ag71xx *ag; + +@@ -1957,10 +1956,8 @@ static int ag71xx_probe(struct platform_ + ag->stop_desc->ctrl = 0; + ag->stop_desc->next = (u32)ag->stop_desc_dma; + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- memcpy(ndev->dev_addr, mac_addr, ETH_ALEN); +- if (IS_ERR(mac_addr) || !is_valid_ether_addr(ndev->dev_addr)) { ++ err = of_get_mac_address(np, ndev->dev_addr); ++ if (err) { + netif_err(ag, probe, ndev, "invalid MAC address, using random address\n"); + eth_random_addr(ndev->dev_addr); + } +--- a/drivers/net/ethernet/broadcom/bcmsysport.c ++++ b/drivers/net/ethernet/broadcom/bcmsysport.c +@@ -2465,7 +2465,6 @@ static int bcm_sysport_probe(struct plat + struct bcm_sysport_priv *priv; + struct device_node *dn; + struct net_device *dev; +- const void *macaddr; + u32 txq, rxq; + int ret; + +@@ -2560,12 +2559,10 @@ static int bcm_sysport_probe(struct plat + } + + /* Initialize netdevice members */ +- macaddr = of_get_mac_address(dn); +- if (IS_ERR(macaddr)) { ++ ret = of_get_mac_address(dn, dev->dev_addr); ++ if (ret) { + dev_warn(&pdev->dev, "using random Ethernet MAC\n"); + eth_hw_addr_random(dev); +- } else { +- ether_addr_copy(dev->dev_addr, macaddr); + } + + SET_NETDEV_DEV(dev, &pdev->dev); +--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c ++++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c +@@ -115,7 +115,7 @@ static int bgmac_probe(struct bcma_devic + struct ssb_sprom *sprom = &core->bus->sprom; + struct mii_bus *mii_bus; + struct bgmac *bgmac; +- const u8 *mac = NULL; ++ const u8 *mac; + int err; + + bgmac = bgmac_alloc(&core->dev); +@@ -128,11 +128,10 @@ static int bgmac_probe(struct bcma_devic + + bcma_set_drvdata(core, bgmac); + +- if (bgmac->dev->of_node) +- mac = of_get_mac_address(bgmac->dev->of_node); ++ err = of_get_mac_address(bgmac->dev->of_node, bgmac->net_dev->dev_addr); + + /* If no MAC address assigned via device tree, check SPROM */ +- if (IS_ERR_OR_NULL(mac)) { ++ if (err) { + switch (core->core_unit) { + case 0: + mac = sprom->et0mac; +@@ -149,10 +148,9 @@ static int bgmac_probe(struct bcma_devic + err = -ENOTSUPP; + goto err; + } ++ ether_addr_copy(bgmac->net_dev->dev_addr, mac); + } + +- ether_addr_copy(bgmac->net_dev->dev_addr, mac); +- + /* On BCM4706 we need common core to access PHY */ + if (core->id.id == BCMA_CORE_4706_MAC_GBIT && + !core->bus->drv_gmac_cmn.core) { +--- a/drivers/net/ethernet/broadcom/bgmac-platform.c ++++ b/drivers/net/ethernet/broadcom/bgmac-platform.c +@@ -173,7 +173,7 @@ static int bgmac_probe(struct platform_d + struct device_node *np = pdev->dev.of_node; + struct bgmac *bgmac; + struct resource *regs; +- const u8 *mac_addr; ++ int ret; + + bgmac = bgmac_alloc(&pdev->dev); + if (!bgmac) +@@ -192,11 +192,10 @@ static int bgmac_probe(struct platform_d + bgmac->dev = &pdev->dev; + bgmac->dma_dev = &pdev->dev; + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(bgmac->net_dev->dev_addr, mac_addr); +- else +- dev_warn(&pdev->dev, "MAC address not present in device tree\n"); ++ ret = of_get_mac_address(np, bgmac->net_dev->dev_addr); ++ if (ret) ++ dev_warn(&pdev->dev, ++ "MAC address not present in device tree\n"); + + bgmac->irq = platform_get_irq(pdev, 0); + if (bgmac->irq < 0) +--- a/drivers/net/ethernet/cadence/macb_main.c ++++ b/drivers/net/ethernet/cadence/macb_main.c +@@ -4456,7 +4456,6 @@ static int macb_probe(struct platform_de + struct net_device *dev; + struct resource *regs; + void __iomem *mem; +- const char *mac; + struct macb *bp; + int err, val; + +@@ -4569,15 +4568,11 @@ static int macb_probe(struct platform_de + if (bp->caps & MACB_CAPS_NEEDS_RSTONUBR) + bp->rx_intr_mask |= MACB_BIT(RXUBR); + +- mac = of_get_mac_address(np); +- if (PTR_ERR(mac) == -EPROBE_DEFER) { +- err = -EPROBE_DEFER; ++ err = of_get_mac_address(np, bp->dev->dev_addr); ++ if (err == -EPROBE_DEFER) + goto err_out_free_netdev; +- } else if (!IS_ERR_OR_NULL(mac)) { +- ether_addr_copy(bp->dev->dev_addr, mac); +- } else { ++ else if (err) + macb_get_hwaddr(bp); +- } + + err = of_get_phy_mode(np, &interface); + if (err) +--- a/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c ++++ b/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c +@@ -1385,7 +1385,6 @@ static int octeon_mgmt_probe(struct plat + struct net_device *netdev; + struct octeon_mgmt *p; + const __be32 *data; +- const u8 *mac; + struct resource *res_mix; + struct resource *res_agl; + struct resource *res_agl_prt_ctl; +@@ -1502,11 +1501,8 @@ static int octeon_mgmt_probe(struct plat + netdev->min_mtu = 64 - OCTEON_MGMT_RX_HEADROOM; + netdev->max_mtu = 16383 - OCTEON_MGMT_RX_HEADROOM - VLAN_HLEN; + +- mac = of_get_mac_address(pdev->dev.of_node); +- +- if (!IS_ERR(mac)) +- ether_addr_copy(netdev->dev_addr, mac); +- else ++ result = of_get_mac_address(pdev->dev.of_node, netdev->dev_addr); ++ if (result) + eth_hw_addr_random(netdev); + + p->phy_np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0); +--- a/drivers/net/ethernet/cavium/thunder/thunder_bgx.c ++++ b/drivers/net/ethernet/cavium/thunder/thunder_bgx.c +@@ -1474,7 +1474,6 @@ static int bgx_init_of_phy(struct bgx *b + device_for_each_child_node(&bgx->pdev->dev, fwn) { + struct phy_device *pd; + struct device_node *phy_np; +- const char *mac; + + /* Should always be an OF node. But if it is not, we + * cannot handle it, so exit the loop. +@@ -1483,9 +1482,7 @@ static int bgx_init_of_phy(struct bgx *b + if (!node) + break; + +- mac = of_get_mac_address(node); +- if (!IS_ERR(mac)) +- ether_addr_copy(bgx->lmac[lmac].mac, mac); ++ of_get_mac_address(node, bgx->lmac[lmac].mac); + + SET_NETDEV_DEV(&bgx->lmac[lmac].netdev, &bgx->pdev->dev); + bgx->lmac[lmac].lmacid = lmac; +--- a/drivers/net/ethernet/davicom/dm9000.c ++++ b/drivers/net/ethernet/davicom/dm9000.c +@@ -1388,7 +1388,7 @@ static struct dm9000_plat_data *dm9000_p + { + struct dm9000_plat_data *pdata; + struct device_node *np = dev->of_node; +- const void *mac_addr; ++ int ret; + + if (!IS_ENABLED(CONFIG_OF) || !np) + return ERR_PTR(-ENXIO); +@@ -1402,11 +1402,9 @@ static struct dm9000_plat_data *dm9000_p + if (of_find_property(np, "davicom,no-eeprom", NULL)) + pdata->flags |= DM9000_PLATF_NO_EEPROM; + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(pdata->dev_addr, mac_addr); +- else if (PTR_ERR(mac_addr) == -EPROBE_DEFER) +- return ERR_CAST(mac_addr); ++ ret = of_get_mac_address(np, pdata->dev_addr); ++ if (ret == -EPROBE_DEFER) ++ return ERR_PTR(ret); + + return pdata; + } +--- a/drivers/net/ethernet/ethoc.c ++++ b/drivers/net/ethernet/ethoc.c +@@ -1151,11 +1151,7 @@ static int ethoc_probe(struct platform_d + ether_addr_copy(netdev->dev_addr, pdata->hwaddr); + priv->phy_id = pdata->phy_id; + } else { +- const void *mac; +- +- mac = of_get_mac_address(pdev->dev.of_node); +- if (!IS_ERR(mac)) +- ether_addr_copy(netdev->dev_addr, mac); ++ of_get_mac_address(pdev->dev.of_node, netdev->dev_addr); + priv->phy_id = -1; + } + +--- a/drivers/net/ethernet/ezchip/nps_enet.c ++++ b/drivers/net/ethernet/ezchip/nps_enet.c +@@ -575,7 +575,6 @@ static s32 nps_enet_probe(struct platfor + struct net_device *ndev; + struct nps_enet_priv *priv; + s32 err = 0; +- const char *mac_addr; + + if (!dev->of_node) + return -ENODEV; +@@ -602,10 +601,8 @@ static s32 nps_enet_probe(struct platfor + dev_dbg(dev, "Registers base address is 0x%p\n", priv->regs_base); + + /* set kernel MAC address to dev */ +- mac_addr = of_get_mac_address(dev->of_node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- else ++ err = of_get_mac_address(dev->of_node, ndev->dev_addr); ++ if (err) + eth_hw_addr_random(ndev); + + /* Get IRQ number */ +--- a/drivers/net/ethernet/freescale/fec_main.c ++++ b/drivers/net/ethernet/freescale/fec_main.c +@@ -1666,6 +1666,7 @@ static void fec_get_mac(struct net_devic + struct fec_enet_private *fep = netdev_priv(ndev); + struct fec_platform_data *pdata = dev_get_platdata(&fep->pdev->dev); + unsigned char *iap, tmpaddr[ETH_ALEN]; ++ int ret; + + /* + * try to get mac address in following order: +@@ -1681,9 +1682,9 @@ static void fec_get_mac(struct net_devic + if (!is_valid_ether_addr(iap)) { + struct device_node *np = fep->pdev->dev.of_node; + if (np) { +- const char *mac = of_get_mac_address(np); +- if (!IS_ERR(mac)) +- iap = (unsigned char *) mac; ++ ret = of_get_mac_address(np, tmpaddr); ++ if (!ret) ++ iap = tmpaddr; + } + } + +--- a/drivers/net/ethernet/freescale/fec_mpc52xx.c ++++ b/drivers/net/ethernet/freescale/fec_mpc52xx.c +@@ -813,7 +813,6 @@ static int mpc52xx_fec_probe(struct plat + const u32 *prop; + int prop_size; + struct device_node *np = op->dev.of_node; +- const char *mac_addr; + + phys_addr_t rx_fifo; + phys_addr_t tx_fifo; +@@ -891,10 +890,8 @@ static int mpc52xx_fec_probe(struct plat + * + * First try to read MAC address from DT + */ +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(ndev->dev_addr, mac_addr); +- } else { ++ rv = of_get_mac_address(np, ndev->dev_addr); ++ if (rv) { + struct mpc52xx_fec __iomem *fec = priv->fec; + + /* +--- a/drivers/net/ethernet/freescale/fman/mac.c ++++ b/drivers/net/ethernet/freescale/fman/mac.c +@@ -605,7 +605,6 @@ static int mac_probe(struct platform_dev + struct platform_device *of_dev; + struct resource res; + struct mac_priv_s *priv; +- const u8 *mac_addr; + u32 val; + u8 fman_id; + phy_interface_t phy_if; +@@ -723,11 +722,9 @@ static int mac_probe(struct platform_dev + priv->cell_index = (u8)val; + + /* Get the MAC address */ +- mac_addr = of_get_mac_address(mac_node); +- if (IS_ERR(mac_addr)) ++ err = of_get_mac_address(mac_node, mac_dev->addr); ++ if (err) + dev_warn(dev, "of_get_mac_address(%pOF) failed\n", mac_node); +- else +- ether_addr_copy(mac_dev->addr, mac_addr); + + /* Get the port handles */ + nph = of_count_phandle_with_args(mac_node, "fsl,fman-ports", NULL); +@@ -853,7 +850,7 @@ static int mac_probe(struct platform_dev + if (err < 0) + dev_err(dev, "fman_set_mac_active_pause() = %d\n", err); + +- if (!IS_ERR(mac_addr)) ++ if (!is_zero_ether_addr(mac_dev->addr)) + dev_info(dev, "FMan MAC address: %pM\n", mac_dev->addr); + + priv->eth_dev = dpaa_eth_add_device(fman_id, mac_dev); +--- a/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c ++++ b/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c +@@ -918,7 +918,6 @@ static int fs_enet_probe(struct platform + const u32 *data; + struct clk *clk; + int err; +- const u8 *mac_addr; + const char *phy_connection_type; + int privsize, len, ret = -ENODEV; + +@@ -1006,9 +1005,7 @@ static int fs_enet_probe(struct platform + spin_lock_init(&fep->lock); + spin_lock_init(&fep->tx_lock); + +- mac_addr = of_get_mac_address(ofdev->dev.of_node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); ++ of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr); + + ret = fep->ops->allocate_bd(ndev); + if (ret) +--- a/drivers/net/ethernet/freescale/gianfar.c ++++ b/drivers/net/ethernet/freescale/gianfar.c +@@ -641,7 +641,6 @@ static phy_interface_t gfar_get_interfac + static int gfar_of_init(struct platform_device *ofdev, struct net_device **pdev) + { + const char *model; +- const void *mac_addr; + int err = 0, i; + phy_interface_t interface; + struct net_device *dev = NULL; +@@ -783,11 +782,8 @@ static int gfar_of_init(struct platform_ + if (stash_len || stash_idx) + priv->device_flags |= FSL_GIANFAR_DEV_HAS_BUF_STASHING; + +- mac_addr = of_get_mac_address(np); +- +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(dev->dev_addr, mac_addr); +- } else { ++ err = of_get_mac_address(np, dev->dev_addr); ++ if (err) { + eth_hw_addr_random(dev); + dev_info(&ofdev->dev, "Using random MAC address: %pM\n", dev->dev_addr); + } +--- a/drivers/net/ethernet/freescale/ucc_geth.c ++++ b/drivers/net/ethernet/freescale/ucc_geth.c +@@ -3696,7 +3696,6 @@ static int ucc_geth_probe(struct platfor + int err, ucc_num, max_speed = 0; + const unsigned int *prop; + const char *sprop; +- const void *mac_addr; + phy_interface_t phy_interface; + static const int enet_to_speed[] = { + SPEED_10, SPEED_10, SPEED_10, +@@ -3906,9 +3905,7 @@ static int ucc_geth_probe(struct platfor + goto err_free_netdev; + } + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(dev->dev_addr, mac_addr); ++ of_get_mac_address(np, dev->dev_addr); + + ugeth->ug_info = ug_info; + ugeth->dev = device; +--- a/drivers/net/ethernet/hisilicon/hisi_femac.c ++++ b/drivers/net/ethernet/hisilicon/hisi_femac.c +@@ -772,7 +772,6 @@ static int hisi_femac_drv_probe(struct p + struct net_device *ndev; + struct hisi_femac_priv *priv; + struct phy_device *phy; +- const char *mac_addr; + int ret; + + ndev = alloc_etherdev(sizeof(*priv)); +@@ -842,10 +841,8 @@ static int hisi_femac_drv_probe(struct p + (unsigned long)phy->phy_id, + phy_modes(phy->interface)); + +- mac_addr = of_get_mac_address(node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- if (!is_valid_ether_addr(ndev->dev_addr)) { ++ ret = of_get_mac_address(node, ndev->dev_addr); ++ if (ret) { + eth_hw_addr_random(ndev); + dev_warn(dev, "using random MAC address %pM\n", + ndev->dev_addr); +--- a/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c ++++ b/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c +@@ -1098,7 +1098,6 @@ static int hix5hd2_dev_probe(struct plat + struct net_device *ndev; + struct hix5hd2_priv *priv; + struct mii_bus *bus; +- const char *mac_addr; + int ret; + + ndev = alloc_etherdev(sizeof(struct hix5hd2_priv)); +@@ -1220,10 +1219,8 @@ static int hix5hd2_dev_probe(struct plat + goto out_phy_node; + } + +- mac_addr = of_get_mac_address(node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- if (!is_valid_ether_addr(ndev->dev_addr)) { ++ ret = of_get_mac_address(node, ndev->dev_addr); ++ if (ret) { + eth_hw_addr_random(ndev); + netdev_warn(ndev, "using random MAC address %pM\n", + ndev->dev_addr); +--- a/drivers/net/ethernet/lantiq_xrx200.c ++++ b/drivers/net/ethernet/lantiq_xrx200.c +@@ -440,7 +440,6 @@ static int xrx200_probe(struct platform_ + struct resource *res; + struct xrx200_priv *priv; + struct net_device *net_dev; +- const u8 *mac; + int err; + + /* alloc the network device */ +@@ -484,10 +483,8 @@ static int xrx200_probe(struct platform_ + return PTR_ERR(priv->clk); + } + +- mac = of_get_mac_address(np); +- if (!IS_ERR(mac)) +- ether_addr_copy(net_dev->dev_addr, mac); +- else ++ err = of_get_mac_address(np, net_dev->dev_addr); ++ if (err) + eth_hw_addr_random(net_dev); + + /* bring up the dma engine and IP core */ +--- a/drivers/net/ethernet/marvell/mv643xx_eth.c ++++ b/drivers/net/ethernet/marvell/mv643xx_eth.c +@@ -2700,7 +2700,6 @@ static int mv643xx_eth_shared_of_add_por + struct platform_device *ppdev; + struct mv643xx_eth_platform_data ppd; + struct resource res; +- const char *mac_addr; + int ret; + int dev_num = 0; + +@@ -2731,9 +2730,7 @@ static int mv643xx_eth_shared_of_add_por + return -EINVAL; + } + +- mac_addr = of_get_mac_address(pnp); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ppd.mac_addr, mac_addr); ++ of_get_mac_address(pnp, ppd.mac_addr); + + mv643xx_eth_property(pnp, "tx-queue-size", ppd.tx_queue_size); + mv643xx_eth_property(pnp, "tx-sram-addr", ppd.tx_sram_addr); +--- a/drivers/net/ethernet/marvell/mvneta.c ++++ b/drivers/net/ethernet/marvell/mvneta.c +@@ -5062,7 +5062,6 @@ static int mvneta_probe(struct platform_ + struct net_device *dev; + struct phylink *phylink; + struct phy *comphy; +- const char *dt_mac_addr; + char hw_mac_addr[ETH_ALEN]; + phy_interface_t phy_mode; + const char *mac_from; +@@ -5158,10 +5157,9 @@ static int mvneta_probe(struct platform_ + goto err_free_ports; + } + +- dt_mac_addr = of_get_mac_address(dn); +- if (!IS_ERR(dt_mac_addr)) { ++ err = of_get_mac_address(dn, dev->dev_addr); ++ if (!err) { + mac_from = "device tree"; +- ether_addr_copy(dev->dev_addr, dt_mac_addr); + } else { + mvneta_get_mac_addr(pp, hw_mac_addr); + if (is_valid_ether_addr(hw_mac_addr)) { +--- a/drivers/net/ethernet/marvell/prestera/prestera_main.c ++++ b/drivers/net/ethernet/marvell/prestera/prestera_main.c +@@ -462,20 +462,17 @@ static int prestera_switch_set_base_mac_ + { + struct device_node *base_mac_np; + struct device_node *np; +- const char *base_mac; ++ int ret; + + np = of_find_compatible_node(NULL, NULL, "marvell,prestera"); + base_mac_np = of_parse_phandle(np, "base-mac-provider", 0); + +- base_mac = of_get_mac_address(base_mac_np); +- of_node_put(base_mac_np); +- if (!IS_ERR(base_mac)) +- ether_addr_copy(sw->base_mac, base_mac); +- +- if (!is_valid_ether_addr(sw->base_mac)) { ++ ret = of_get_mac_address(base_mac_np, sw->base_mac); ++ if (ret) { + eth_random_addr(sw->base_mac); + dev_info(prestera_dev(sw), "using random base mac address\n"); + } ++ of_node_put(base_mac_np); + + return prestera_hw_switch_mac_set(sw, sw->base_mac); + } +--- a/drivers/net/ethernet/marvell/pxa168_eth.c ++++ b/drivers/net/ethernet/marvell/pxa168_eth.c +@@ -1392,7 +1392,6 @@ static int pxa168_eth_probe(struct platf + struct resource *res; + struct clk *clk; + struct device_node *np; +- const unsigned char *mac_addr = NULL; + int err; + + printk(KERN_NOTICE "PXA168 10/100 Ethernet Driver\n"); +@@ -1435,12 +1434,8 @@ static int pxa168_eth_probe(struct platf + + INIT_WORK(&pep->tx_timeout_task, pxa168_eth_tx_timeout_task); + +- if (pdev->dev.of_node) +- mac_addr = of_get_mac_address(pdev->dev.of_node); +- +- if (!IS_ERR_OR_NULL(mac_addr)) { +- ether_addr_copy(dev->dev_addr, mac_addr); +- } else { ++ err = of_get_mac_address(pdev->dev.of_node, dev->dev_addr); ++ if (err) { + /* try reading the mac address, if set by the bootloader */ + pxa168_eth_get_mac_address(dev, dev->dev_addr); + if (!is_valid_ether_addr(dev->dev_addr)) { +--- a/drivers/net/ethernet/marvell/sky2.c ++++ b/drivers/net/ethernet/marvell/sky2.c +@@ -4725,7 +4725,7 @@ static struct net_device *sky2_init_netd + { + struct sky2_port *sky2; + struct net_device *dev = alloc_etherdev(sizeof(*sky2)); +- const void *iap; ++ int ret; + + if (!dev) + return NULL; +@@ -4795,10 +4795,8 @@ static struct net_device *sky2_init_netd + * 1) from device tree data + * 2) from internal registers set by bootloader + */ +- iap = of_get_mac_address(hw->pdev->dev.of_node); +- if (!IS_ERR(iap)) +- ether_addr_copy(dev->dev_addr, iap); +- else ++ ret = of_get_mac_address(hw->pdev->dev.of_node, dev->dev_addr); ++ if (ret) + memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, + ETH_ALEN); + +--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c ++++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c +@@ -2580,14 +2580,11 @@ static int __init mtk_init(struct net_de + { + struct mtk_mac *mac = netdev_priv(dev); + struct mtk_eth *eth = mac->hw; +- const char *mac_addr; ++ int ret; + +- mac_addr = of_get_mac_address(mac->of_node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(dev->dev_addr, mac_addr); +- +- /* If the mac address is invalid, use random mac address */ +- if (!is_valid_ether_addr(dev->dev_addr)) { ++ ret = of_get_mac_address(mac->of_node, dev->dev_addr); ++ if (ret) { ++ /* If the mac address is invalid, use random mac address */ + eth_hw_addr_random(dev); + dev_err(eth->dev, "generated random MAC address %pM\n", + dev->dev_addr); +--- a/drivers/net/ethernet/micrel/ks8851_common.c ++++ b/drivers/net/ethernet/micrel/ks8851_common.c +@@ -194,11 +194,10 @@ static void ks8851_read_mac_addr(struct + static void ks8851_init_mac(struct ks8851_net *ks, struct device_node *np) + { + struct net_device *dev = ks->netdev; +- const u8 *mac_addr; ++ int ret; + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(dev->dev_addr, mac_addr); ++ ret = of_get_mac_address(np, dev->dev_addr); ++ if (!ret) { + ks8851_write_mac_addr(dev); + return; + } +--- a/drivers/net/ethernet/microchip/lan743x_main.c ++++ b/drivers/net/ethernet/microchip/lan743x_main.c +@@ -2835,7 +2835,6 @@ static int lan743x_pcidev_probe(struct p + { + struct lan743x_adapter *adapter = NULL; + struct net_device *netdev = NULL; +- const void *mac_addr; + int ret = -ENODEV; + + netdev = devm_alloc_etherdev(&pdev->dev, +@@ -2852,9 +2851,7 @@ static int lan743x_pcidev_probe(struct p + NETIF_MSG_IFDOWN | NETIF_MSG_TX_QUEUED; + netdev->max_mtu = LAN743X_MAX_FRAME_SIZE; + +- mac_addr = of_get_mac_address(pdev->dev.of_node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(adapter->mac_address, mac_addr); ++ of_get_mac_address(pdev->dev.of_node, adapter->mac_address); + + ret = lan743x_pci_init(adapter, pdev); + if (ret) +--- a/drivers/net/ethernet/nxp/lpc_eth.c ++++ b/drivers/net/ethernet/nxp/lpc_eth.c +@@ -1347,9 +1347,7 @@ static int lpc_eth_drv_probe(struct plat + __lpc_get_mac(pldat, ndev->dev_addr); + + if (!is_valid_ether_addr(ndev->dev_addr)) { +- const char *macaddr = of_get_mac_address(np); +- if (!IS_ERR(macaddr)) +- ether_addr_copy(ndev->dev_addr, macaddr); ++ of_get_mac_address(np, ndev->dev_addr); + } + if (!is_valid_ether_addr(ndev->dev_addr)) + eth_hw_addr_random(ndev); +--- a/drivers/net/ethernet/qualcomm/qca_spi.c ++++ b/drivers/net/ethernet/qualcomm/qca_spi.c +@@ -885,7 +885,7 @@ qca_spi_probe(struct spi_device *spi) + struct net_device *qcaspi_devs = NULL; + u8 legacy_mode = 0; + u16 signature; +- const char *mac; ++ int ret; + + if (!spi->dev.of_node) { + dev_err(&spi->dev, "Missing device tree\n"); +@@ -962,12 +962,8 @@ qca_spi_probe(struct spi_device *spi) + + spi_set_drvdata(spi, qcaspi_devs); + +- mac = of_get_mac_address(spi->dev.of_node); +- +- if (!IS_ERR(mac)) +- ether_addr_copy(qca->net_dev->dev_addr, mac); +- +- if (!is_valid_ether_addr(qca->net_dev->dev_addr)) { ++ ret = of_get_mac_address(spi->dev.of_node, qca->net_dev->dev_addr); ++ if (ret) { + eth_hw_addr_random(qca->net_dev); + dev_info(&spi->dev, "Using random MAC address: %pM\n", + qca->net_dev->dev_addr); +--- a/drivers/net/ethernet/qualcomm/qca_uart.c ++++ b/drivers/net/ethernet/qualcomm/qca_uart.c +@@ -323,7 +323,6 @@ static int qca_uart_probe(struct serdev_ + { + struct net_device *qcauart_dev = alloc_etherdev(sizeof(struct qcauart)); + struct qcauart *qca; +- const char *mac; + u32 speed = 115200; + int ret; + +@@ -348,12 +347,8 @@ static int qca_uart_probe(struct serdev_ + + of_property_read_u32(serdev->dev.of_node, "current-speed", &speed); + +- mac = of_get_mac_address(serdev->dev.of_node); +- +- if (!IS_ERR(mac)) +- ether_addr_copy(qca->net_dev->dev_addr, mac); +- +- if (!is_valid_ether_addr(qca->net_dev->dev_addr)) { ++ ret = of_get_mac_address(serdev->dev.of_node, qca->net_dev->dev_addr); ++ if (ret) { + eth_hw_addr_random(qca->net_dev); + dev_info(&serdev->dev, "Using random MAC address: %pM\n", + qca->net_dev->dev_addr); +--- a/drivers/net/ethernet/renesas/ravb_main.c ++++ b/drivers/net/ethernet/renesas/ravb_main.c +@@ -109,11 +109,13 @@ static void ravb_set_buffer_align(struct + * Ethernet AVB device doesn't have ROM for MAC address. + * This function gets the MAC address that was used by a bootloader. + */ +-static void ravb_read_mac_address(struct net_device *ndev, const u8 *mac) ++static void ravb_read_mac_address(struct device_node *np, ++ struct net_device *ndev) + { +- if (!IS_ERR(mac)) { +- ether_addr_copy(ndev->dev_addr, mac); +- } else { ++ int ret; ++ ++ ret = of_get_mac_address(np, ndev->dev_addr); ++ if (ret) { + u32 mahr = ravb_read(ndev, MAHR); + u32 malr = ravb_read(ndev, MALR); + +@@ -2189,7 +2191,7 @@ static int ravb_probe(struct platform_de + priv->msg_enable = RAVB_DEF_MSG_ENABLE; + + /* Read and set MAC address */ +- ravb_read_mac_address(ndev, of_get_mac_address(np)); ++ ravb_read_mac_address(np, ndev); + if (!is_valid_ether_addr(ndev->dev_addr)) { + dev_warn(&pdev->dev, + "no valid MAC address supplied, using a random one\n"); +--- a/drivers/net/ethernet/renesas/sh_eth.c ++++ b/drivers/net/ethernet/renesas/sh_eth.c +@@ -3145,7 +3145,6 @@ static struct sh_eth_plat_data *sh_eth_p + struct device_node *np = dev->of_node; + struct sh_eth_plat_data *pdata; + phy_interface_t interface; +- const char *mac_addr; + int ret; + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); +@@ -3157,9 +3156,7 @@ static struct sh_eth_plat_data *sh_eth_p + return NULL; + pdata->phy_interface = interface; + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(pdata->mac_addr, mac_addr); ++ of_get_mac_address(np, pdata->mac_addr); + + pdata->no_ether_link = + of_property_read_bool(np, "renesas,no-ether-link"); +--- a/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c ++++ b/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c +@@ -25,8 +25,7 @@ + + #ifdef CONFIG_OF + static int sxgbe_probe_config_dt(struct platform_device *pdev, +- struct sxgbe_plat_data *plat, +- const char **mac) ++ struct sxgbe_plat_data *plat) + { + struct device_node *np = pdev->dev.of_node; + struct sxgbe_dma_cfg *dma_cfg; +@@ -35,7 +34,6 @@ static int sxgbe_probe_config_dt(struct + if (!np) + return -ENODEV; + +- *mac = of_get_mac_address(np); + err = of_get_phy_mode(np, &plat->interface); + if (err && err != -ENODEV) + return err; +@@ -63,8 +61,7 @@ static int sxgbe_probe_config_dt(struct + } + #else + static int sxgbe_probe_config_dt(struct platform_device *pdev, +- struct sxgbe_plat_data *plat, +- const char **mac) ++ struct sxgbe_plat_data *plat) + { + return -ENOSYS; + } +@@ -85,7 +82,6 @@ static int sxgbe_platform_probe(struct p + void __iomem *addr; + struct sxgbe_priv_data *priv = NULL; + struct sxgbe_plat_data *plat_dat = NULL; +- const char *mac = NULL; + struct net_device *ndev = platform_get_drvdata(pdev); + struct device_node *node = dev->of_node; + +@@ -101,7 +97,7 @@ static int sxgbe_platform_probe(struct p + if (!plat_dat) + return -ENOMEM; + +- ret = sxgbe_probe_config_dt(pdev, plat_dat, &mac); ++ ret = sxgbe_probe_config_dt(pdev, plat_dat); + if (ret) { + pr_err("%s: main dt probe failed\n", __func__); + return ret; +@@ -122,8 +118,7 @@ static int sxgbe_platform_probe(struct p + } + + /* Get MAC address if available (DT) */ +- if (!IS_ERR_OR_NULL(mac)) +- ether_addr_copy(priv->dev->dev_addr, mac); ++ of_get_mac_address(node, priv->dev->dev_addr); + + /* Get the TX/RX IRQ numbers */ + for (i = 0, chan = 1; i < SXGBE_TX_QUEUES; i++) { +--- a/drivers/net/ethernet/socionext/sni_ave.c ++++ b/drivers/net/ethernet/socionext/sni_ave.c +@@ -1559,7 +1559,6 @@ static int ave_probe(struct platform_dev + struct ave_private *priv; + struct net_device *ndev; + struct device_node *np; +- const void *mac_addr; + void __iomem *base; + const char *name; + int i, irq, ret; +@@ -1600,12 +1599,9 @@ static int ave_probe(struct platform_dev + + ndev->max_mtu = AVE_MAX_ETHFRAME - (ETH_HLEN + ETH_FCS_LEN); + +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- +- /* if the mac address is invalid, use random mac address */ +- if (!is_valid_ether_addr(ndev->dev_addr)) { ++ ret = of_get_mac_address(np, ndev->dev_addr); ++ if (ret) { ++ /* if the mac address is invalid, use random mac address */ + eth_hw_addr_random(ndev); + dev_warn(dev, "Using random MAC address: %pM\n", + ndev->dev_addr); +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-anarion.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-anarion.c +@@ -115,7 +115,7 @@ static int anarion_dwmac_probe(struct pl + if (IS_ERR(gmac)) + return PTR_ERR(gmac); + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c +@@ -444,7 +444,7 @@ static int dwc_eth_dwmac_probe(struct pl + if (IS_ERR(stmmac_res.addr)) + return PTR_ERR(stmmac_res.addr); + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-generic.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-generic.c +@@ -27,7 +27,7 @@ static int dwmac_generic_probe(struct pl + return ret; + + if (pdev->dev.of_node) { +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) { + dev_err(&pdev->dev, "dt configuration failed\n"); + return PTR_ERR(plat_dat); +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c +@@ -226,7 +226,7 @@ static int imx_dwmac_probe(struct platfo + if (!dwmac) + return -ENOMEM; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c +@@ -88,7 +88,7 @@ static int intel_eth_plat_probe(struct p + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) { + dev_err(&pdev->dev, "dt configuration failed\n"); + return PTR_ERR(plat_dat); +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c +@@ -255,7 +255,7 @@ static int ipq806x_gmac_probe(struct pla + if (val) + return val; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +@@ -37,7 +37,7 @@ static int lpc18xx_dwmac_probe(struct pl + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c +@@ -407,7 +407,7 @@ static int mediatek_dwmac_probe(struct p + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c +@@ -52,7 +52,7 @@ static int meson6_dwmac_probe(struct pla + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c +@@ -372,7 +372,7 @@ static int meson8b_dwmac_probe(struct pl + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c +@@ -118,7 +118,7 @@ static int oxnas_dwmac_probe(struct plat + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +@@ -461,7 +461,7 @@ static int qcom_ethqos_probe(struct plat + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) { + dev_err(&pdev->dev, "dt configuration failed\n"); + return PTR_ERR(plat_dat); +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c +@@ -1396,7 +1396,7 @@ static int rk_gmac_probe(struct platform + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c +@@ -398,7 +398,7 @@ static int socfpga_dwmac_probe(struct pl + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +@@ -325,7 +325,7 @@ static int sti_dwmac_probe(struct platfo + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c +@@ -371,7 +371,7 @@ static int stm32_dwmac_probe(struct plat + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +@@ -1202,7 +1202,7 @@ static int sun8i_dwmac_probe(struct plat + if (ret) + return -EINVAL; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c ++++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c +@@ -108,7 +108,7 @@ static int sun7i_gmac_probe(struct platf + if (ret) + return ret; + +- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); ++ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); + if (IS_ERR(plat_dat)) + return PTR_ERR(plat_dat); + +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h +@@ -25,7 +25,7 @@ + + struct stmmac_resources { + void __iomem *addr; +- const char *mac; ++ u8 mac[ETH_ALEN]; + int wol_irq; + int lpi_irq; + int irq; +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +@@ -4904,7 +4904,7 @@ int stmmac_dvr_probe(struct device *devi + priv->wol_irq = res->wol_irq; + priv->lpi_irq = res->lpi_irq; + +- if (!IS_ERR_OR_NULL(res->mac)) ++ if (!is_zero_ether_addr(res->mac)) + memcpy(priv->dev->dev_addr, res->mac, ETH_ALEN); + + dev_set_drvdata(device, priv->dev); +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +@@ -394,7 +394,7 @@ static int stmmac_of_get_mac_mode(struct + * set some private fields that will be used by the main at runtime. + */ + struct plat_stmmacenet_data * +-stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) ++stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) + { + struct device_node *np = pdev->dev.of_node; + struct plat_stmmacenet_data *plat; +@@ -406,12 +406,12 @@ stmmac_probe_config_dt(struct platform_d + if (!plat) + return ERR_PTR(-ENOMEM); + +- *mac = of_get_mac_address(np); +- if (IS_ERR(*mac)) { +- if (PTR_ERR(*mac) == -EPROBE_DEFER) +- return ERR_CAST(*mac); ++ rc = of_get_mac_address(np, mac); ++ if (rc) { ++ if (rc == -EPROBE_DEFER) ++ return ERR_PTR(rc); + +- *mac = NULL; ++ eth_zero_addr(mac); + } + + phy_mode = device_get_phy_mode(&pdev->dev); +@@ -643,7 +643,7 @@ void stmmac_remove_config_dt(struct plat + } + #else + struct plat_stmmacenet_data * +-stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) ++stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) + { + return ERR_PTR(-EINVAL); + } +--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h ++++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h +@@ -12,7 +12,7 @@ + #include "stmmac.h" + + struct plat_stmmacenet_data * +-stmmac_probe_config_dt(struct platform_device *pdev, const char **mac); ++stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac); + void stmmac_remove_config_dt(struct platform_device *pdev, + struct plat_stmmacenet_data *plat); + +--- a/drivers/net/ethernet/ti/am65-cpsw-nuss.c ++++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.c +@@ -1741,7 +1741,6 @@ static int am65_cpsw_nuss_init_slave_por + + for_each_child_of_node(node, port_np) { + struct am65_cpsw_port *port; +- const void *mac_addr; + u32 port_id; + + /* it is not a slave port node, continue */ +@@ -1820,15 +1819,15 @@ static int am65_cpsw_nuss_init_slave_por + return ret; + } + +- mac_addr = of_get_mac_address(port_np); +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(port->slave.mac_addr, mac_addr); +- } else if (am65_cpsw_am654_get_efuse_macid(port_np, +- port->port_id, +- port->slave.mac_addr) || +- !is_valid_ether_addr(port->slave.mac_addr)) { +- random_ether_addr(port->slave.mac_addr); +- dev_err(dev, "Use random MAC address\n"); ++ ret = of_get_mac_address(port_np, port->slave.mac_addr); ++ if (ret) { ++ am65_cpsw_am654_get_efuse_macid(port_np, ++ port->port_id, ++ port->slave.mac_addr); ++ if (!is_valid_ether_addr(port->slave.mac_addr)) { ++ random_ether_addr(port->slave.mac_addr); ++ dev_err(dev, "Use random MAC address\n"); ++ } + } + } + of_node_put(node); +--- a/drivers/net/ethernet/ti/cpsw.c ++++ b/drivers/net/ethernet/ti/cpsw.c +@@ -1306,7 +1306,6 @@ static int cpsw_probe_dt(struct cpsw_pla + + for_each_available_child_of_node(node, slave_node) { + struct cpsw_slave_data *slave_data = data->slave_data + i; +- const void *mac_addr = NULL; + int lenp; + const __be32 *parp; + +@@ -1378,10 +1377,8 @@ static int cpsw_probe_dt(struct cpsw_pla + } + + no_phy_slave: +- mac_addr = of_get_mac_address(slave_node); +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(slave_data->mac_addr, mac_addr); +- } else { ++ ret = of_get_mac_address(slave_node, slave_data->mac_addr); ++ if (ret) { + ret = ti_cm_get_macid(&pdev->dev, i, + slave_data->mac_addr); + if (ret) +--- a/drivers/net/ethernet/ti/cpsw_new.c ++++ b/drivers/net/ethernet/ti/cpsw_new.c +@@ -1267,7 +1267,6 @@ static int cpsw_probe_dt(struct cpsw_com + + for_each_child_of_node(tmp_node, port_np) { + struct cpsw_slave_data *slave_data; +- const void *mac_addr; + u32 port_id; + + ret = of_property_read_u32(port_np, "reg", &port_id); +@@ -1326,10 +1325,8 @@ static int cpsw_probe_dt(struct cpsw_com + goto err_node_put; + } + +- mac_addr = of_get_mac_address(port_np); +- if (!IS_ERR(mac_addr)) { +- ether_addr_copy(slave_data->mac_addr, mac_addr); +- } else { ++ ret = of_get_mac_address(port_np, slave_data->mac_addr); ++ if (ret) { + ret = ti_cm_get_macid(dev, port_id - 1, + slave_data->mac_addr); + if (ret) +--- a/drivers/net/ethernet/ti/davinci_emac.c ++++ b/drivers/net/ethernet/ti/davinci_emac.c +@@ -1687,7 +1687,6 @@ davinci_emac_of_get_pdata(struct platfor + const struct of_device_id *match; + const struct emac_platform_data *auxdata; + struct emac_platform_data *pdata = NULL; +- const u8 *mac_addr; + + if (!IS_ENABLED(CONFIG_OF) || !pdev->dev.of_node) + return dev_get_platdata(&pdev->dev); +@@ -1699,11 +1698,8 @@ davinci_emac_of_get_pdata(struct platfor + np = pdev->dev.of_node; + pdata->version = EMAC_VERSION_2; + +- if (!is_valid_ether_addr(pdata->mac_addr)) { +- mac_addr = of_get_mac_address(np); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(pdata->mac_addr, mac_addr); +- } ++ if (!is_valid_ether_addr(pdata->mac_addr)) ++ of_get_mac_address(np, pdata->mac_addr); + + of_property_read_u32(np, "ti,davinci-ctrl-reg-offset", + &pdata->ctrl_reg_offset); +--- a/drivers/net/ethernet/ti/netcp_core.c ++++ b/drivers/net/ethernet/ti/netcp_core.c +@@ -1966,7 +1966,6 @@ static int netcp_create_interface(struct + struct resource res; + void __iomem *efuse = NULL; + u32 efuse_mac = 0; +- const void *mac_addr; + u8 efuse_mac_addr[6]; + u32 temp[2]; + int ret = 0; +@@ -2036,10 +2035,8 @@ static int netcp_create_interface(struct + devm_iounmap(dev, efuse); + devm_release_mem_region(dev, res.start, size); + } else { +- mac_addr = of_get_mac_address(node_interface); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(ndev->dev_addr, mac_addr); +- else ++ ret = of_get_mac_address(node_interface, ndev->dev_addr); ++ if (ret) + eth_random_addr(ndev->dev_addr); + } + +--- a/drivers/net/ethernet/wiznet/w5100-spi.c ++++ b/drivers/net/ethernet/wiznet/w5100-spi.c +@@ -423,8 +423,14 @@ static int w5100_spi_probe(struct spi_de + const struct of_device_id *of_id; + const struct w5100_ops *ops; + kernel_ulong_t driver_data; ++ const void *mac = NULL; ++ u8 tmpmac[ETH_ALEN]; + int priv_size; +- const void *mac = of_get_mac_address(spi->dev.of_node); ++ int ret; ++ ++ ret = of_get_mac_address(spi->dev.of_node, tmpmac); ++ if (!ret) ++ mac = tmpmac; + + if (spi->dev.of_node) { + of_id = of_match_device(w5100_of_match, &spi->dev); +--- a/drivers/net/ethernet/wiznet/w5100.c ++++ b/drivers/net/ethernet/wiznet/w5100.c +@@ -1159,7 +1159,7 @@ int w5100_probe(struct device *dev, cons + INIT_WORK(&priv->setrx_work, w5100_setrx_work); + INIT_WORK(&priv->restart_work, w5100_restart_work); + +- if (!IS_ERR_OR_NULL(mac_addr)) ++ if (mac_addr) + memcpy(ndev->dev_addr, mac_addr, ETH_ALEN); + else + eth_hw_addr_random(ndev); +--- a/drivers/net/ethernet/xilinx/ll_temac_main.c ++++ b/drivers/net/ethernet/xilinx/ll_temac_main.c +@@ -438,7 +438,7 @@ static void temac_do_set_mac_address(str + + static int temac_init_mac_address(struct net_device *ndev, const void *address) + { +- ether_addr_copy(ndev->dev_addr, address); ++ memcpy(ndev->dev_addr, address, ETH_ALEN); + if (!is_valid_ether_addr(ndev->dev_addr)) + eth_hw_addr_random(ndev); + temac_do_set_mac_address(ndev); +@@ -1370,7 +1370,7 @@ static int temac_probe(struct platform_d + struct device_node *temac_np = dev_of_node(&pdev->dev), *dma_np; + struct temac_local *lp; + struct net_device *ndev; +- const void *addr; ++ u8 addr[ETH_ALEN]; + __be32 *p; + bool little_endian; + int rc = 0; +@@ -1561,8 +1561,8 @@ static int temac_probe(struct platform_d + + if (temac_np) { + /* Retrieve the MAC address */ +- addr = of_get_mac_address(temac_np); +- if (IS_ERR(addr)) { ++ rc = of_get_mac_address(temac_np, addr); ++ if (rc) { + dev_err(&pdev->dev, "could not find MAC address\n"); + return -ENODEV; + } +--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c ++++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c +@@ -1803,8 +1803,8 @@ static int axienet_probe(struct platform + struct device_node *np; + struct axienet_local *lp; + struct net_device *ndev; +- const void *mac_addr; + struct resource *ethres; ++ u8 mac_addr[ETH_ALEN]; + int addr_width = 32; + u32 value; + +@@ -2004,13 +2004,14 @@ static int axienet_probe(struct platform + dev_info(&pdev->dev, "Ethernet core IRQ not defined\n"); + + /* Retrieve the MAC address */ +- mac_addr = of_get_mac_address(pdev->dev.of_node); +- if (IS_ERR(mac_addr)) { +- dev_warn(&pdev->dev, "could not find MAC address property: %ld\n", +- PTR_ERR(mac_addr)); +- mac_addr = NULL; ++ ret = of_get_mac_address(pdev->dev.of_node, mac_addr); ++ if (!ret) { ++ axienet_set_mac_address(ndev, mac_addr); ++ } else { ++ dev_warn(&pdev->dev, "could not find MAC address property: %d\n", ++ ret); ++ axienet_set_mac_address(ndev, NULL); + } +- axienet_set_mac_address(ndev, mac_addr); + + lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD; + lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD; +--- a/drivers/net/ethernet/xilinx/xilinx_emaclite.c ++++ b/drivers/net/ethernet/xilinx/xilinx_emaclite.c +@@ -1113,7 +1113,6 @@ static int xemaclite_of_probe(struct pla + struct net_device *ndev = NULL; + struct net_local *lp = NULL; + struct device *dev = &ofdev->dev; +- const void *mac_address; + + int rc = 0; + +@@ -1155,12 +1154,9 @@ static int xemaclite_of_probe(struct pla + lp->next_rx_buf_to_use = 0x0; + lp->tx_ping_pong = get_bool(ofdev, "xlnx,tx-ping-pong"); + lp->rx_ping_pong = get_bool(ofdev, "xlnx,rx-ping-pong"); +- mac_address = of_get_mac_address(ofdev->dev.of_node); + +- if (!IS_ERR(mac_address)) { +- /* Set the MAC address. */ +- ether_addr_copy(ndev->dev_addr, mac_address); +- } else { ++ rc = of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr); ++ if (rc) { + dev_warn(dev, "No MAC address found, using random\n"); + eth_hw_addr_random(ndev); + } +--- a/drivers/net/wireless/ath/ath9k/init.c ++++ b/drivers/net/wireless/ath/ath9k/init.c +@@ -618,7 +618,6 @@ static int ath9k_of_init(struct ath_soft + struct ath_hw *ah = sc->sc_ah; + struct ath_common *common = ath9k_hw_common(ah); + enum ath_bus_type bus_type = common->bus_ops->ath_bus_type; +- const char *mac; + char eeprom_name[100]; + int ret; + +@@ -641,9 +640,7 @@ static int ath9k_of_init(struct ath_soft + ah->ah_flags |= AH_NO_EEP_SWAP; + } + +- mac = of_get_mac_address(np); +- if (!IS_ERR(mac)) +- ether_addr_copy(common->macaddr, mac); ++ of_get_mac_address(np, common->macaddr); + + return 0; + } +--- a/drivers/net/wireless/mediatek/mt76/eeprom.c ++++ b/drivers/net/wireless/mediatek/mt76/eeprom.c +@@ -90,15 +90,9 @@ out_put_node: + void + mt76_eeprom_override(struct mt76_dev *dev) + { +-#ifdef CONFIG_OF + struct device_node *np = dev->dev->of_node; +- const u8 *mac = NULL; + +- if (np) +- mac = of_get_mac_address(np); +- if (!IS_ERR_OR_NULL(mac)) +- ether_addr_copy(dev->macaddr, mac); +-#endif ++ of_get_mac_address(np, dev->macaddr); + + if (!is_valid_ether_addr(dev->macaddr)) { + eth_random_addr(dev->macaddr); +--- a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c ++++ b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c +@@ -990,11 +990,7 @@ static void rt2x00lib_rate(struct ieee80 + + void rt2x00lib_set_mac_address(struct rt2x00_dev *rt2x00dev, u8 *eeprom_mac_addr) + { +- const char *mac_addr; +- +- mac_addr = of_get_mac_address(rt2x00dev->dev->of_node); +- if (!IS_ERR(mac_addr)) +- ether_addr_copy(eeprom_mac_addr, mac_addr); ++ of_get_mac_address(rt2x00dev->dev->of_node, eeprom_mac_addr); + + if (!is_valid_ether_addr(eeprom_mac_addr)) { + eth_random_addr(eeprom_mac_addr); +--- a/drivers/of/of_net.c ++++ b/drivers/of/of_net.c +@@ -45,37 +45,29 @@ int of_get_phy_mode(struct device_node * + } + EXPORT_SYMBOL_GPL(of_get_phy_mode); + +-static const void *of_get_mac_addr(struct device_node *np, const char *name) ++static int of_get_mac_addr(struct device_node *np, const char *name, u8 *addr) + { + struct property *pp = of_find_property(np, name, NULL); + +- if (pp && pp->length == ETH_ALEN && is_valid_ether_addr(pp->value)) +- return pp->value; +- return NULL; ++ if (pp && pp->length == ETH_ALEN && is_valid_ether_addr(pp->value)) { ++ memcpy(addr, pp->value, ETH_ALEN); ++ return 0; ++ } ++ return -ENODEV; + } + +-static const void *of_get_mac_addr_nvmem(struct device_node *np) ++static int of_get_mac_addr_nvmem(struct device_node *np, u8 *addr) + { +- int ret; +- const void *mac; +- u8 nvmem_mac[ETH_ALEN]; + struct platform_device *pdev = of_find_device_by_node(np); ++ int ret; + + if (!pdev) +- return ERR_PTR(-ENODEV); ++ return -ENODEV; + +- ret = nvmem_get_mac_address(&pdev->dev, &nvmem_mac); +- if (ret) { +- put_device(&pdev->dev); +- return ERR_PTR(ret); +- } +- +- mac = devm_kmemdup(&pdev->dev, nvmem_mac, ETH_ALEN, GFP_KERNEL); ++ ret = nvmem_get_mac_address(&pdev->dev, addr); + put_device(&pdev->dev); +- if (!mac) +- return ERR_PTR(-ENOMEM); + +- return mac; ++ return ret; + } + + /** +@@ -98,24 +90,27 @@ static const void *of_get_mac_addr_nvmem + * this case, the real MAC is in 'local-mac-address', and 'mac-address' exists + * but is all zeros. + * +- * Return: Will be a valid pointer on success and ERR_PTR in case of error. ++ * Return: 0 on success and errno in case of error. + */ +-const void *of_get_mac_address(struct device_node *np) ++int of_get_mac_address(struct device_node *np, u8 *addr) + { +- const void *addr; +- +- addr = of_get_mac_addr(np, "mac-address"); +- if (addr) +- return addr; ++ int ret; + +- addr = of_get_mac_addr(np, "local-mac-address"); +- if (addr) +- return addr; ++ if (!np) ++ return -ENODEV; + +- addr = of_get_mac_addr(np, "address"); +- if (addr) +- return addr; ++ ret = of_get_mac_addr(np, "mac-address", addr); ++ if (!ret) ++ return 0; ++ ++ ret = of_get_mac_addr(np, "local-mac-address", addr); ++ if (!ret) ++ return 0; ++ ++ ret = of_get_mac_addr(np, "address", addr); ++ if (!ret) ++ return 0; + +- return of_get_mac_addr_nvmem(np); ++ return of_get_mac_addr_nvmem(np, addr); + } + EXPORT_SYMBOL(of_get_mac_address); +--- a/drivers/staging/octeon/ethernet.c ++++ b/drivers/staging/octeon/ethernet.c +@@ -407,14 +407,10 @@ static int cvm_oct_common_set_mac_addres + int cvm_oct_common_init(struct net_device *dev) + { + struct octeon_ethernet *priv = netdev_priv(dev); +- const u8 *mac = NULL; ++ int ret; + +- if (priv->of_node) +- mac = of_get_mac_address(priv->of_node); +- +- if (!IS_ERR_OR_NULL(mac)) +- ether_addr_copy(dev->dev_addr, mac); +- else ++ ret = of_get_mac_address(priv->of_node, dev->dev_addr); ++ if (ret) + eth_hw_addr_random(dev); + + /* +--- a/drivers/staging/wfx/main.c ++++ b/drivers/staging/wfx/main.c +@@ -334,7 +334,6 @@ int wfx_probe(struct wfx_dev *wdev) + { + int i; + int err; +- const void *macaddr; + struct gpio_desc *gpio_saved; + + // During first part of boot, gpio_wakeup cannot yet been used. So +@@ -423,9 +422,9 @@ int wfx_probe(struct wfx_dev *wdev) + + for (i = 0; i < ARRAY_SIZE(wdev->addresses); i++) { + eth_zero_addr(wdev->addresses[i].addr); +- macaddr = of_get_mac_address(wdev->dev->of_node); +- if (!IS_ERR_OR_NULL(macaddr)) { +- ether_addr_copy(wdev->addresses[i].addr, macaddr); ++ err = of_get_mac_address(wdev->dev->of_node, ++ wdev->addresses[i].addr); ++ if (!err) { + wdev->addresses[i].addr[ETH_ALEN - 1] += i; + } else { + ether_addr_copy(wdev->addresses[i].addr, +--- a/include/linux/of_net.h ++++ b/include/linux/of_net.h +@@ -13,7 +13,7 @@ + + struct net_device; + extern int of_get_phy_mode(struct device_node *np, phy_interface_t *interface); +-extern const void *of_get_mac_address(struct device_node *np); ++extern int of_get_mac_address(struct device_node *np, u8 *mac); + extern struct net_device *of_find_net_device_by_node(struct device_node *np); + #else + static inline int of_get_phy_mode(struct device_node *np, +@@ -22,9 +22,9 @@ static inline int of_get_phy_mode(struct + return -ENODEV; + } + +-static inline const void *of_get_mac_address(struct device_node *np) ++static inline int of_get_mac_address(struct device_node *np, u8 *mac) + { +- return ERR_PTR(-ENODEV); ++ return -ENODEV; + } + + static inline struct net_device *of_find_net_device_by_node(struct device_node *np) +--- a/include/net/dsa.h ++++ b/include/net/dsa.h +@@ -208,7 +208,7 @@ struct dsa_port { + unsigned int index; + const char *name; + struct dsa_port *cpu_dp; +- const char *mac; ++ u8 mac[ETH_ALEN]; + struct device_node *dn; + unsigned int ageing_time; + bool vlan_filtering; +--- a/net/dsa/dsa2.c ++++ b/net/dsa/dsa2.c +@@ -288,7 +288,7 @@ static int dsa_port_setup(struct dsa_por + + break; + case DSA_PORT_TYPE_USER: +- dp->mac = of_get_mac_address(dp->dn); ++ of_get_mac_address(dp->dn, dp->mac); + err = dsa_slave_create(dp); + if (err) + break; +--- a/net/dsa/slave.c ++++ b/net/dsa/slave.c +@@ -1855,7 +1855,7 @@ int dsa_slave_create(struct dsa_port *po + slave_dev->hw_features |= NETIF_F_HW_TC; + slave_dev->features |= NETIF_F_LLTX; + slave_dev->ethtool_ops = &dsa_slave_ethtool_ops; +- if (!IS_ERR_OR_NULL(port->mac)) ++ if (!is_zero_ether_addr(port->mac)) + ether_addr_copy(slave_dev->dev_addr, port->mac); + else + eth_hw_addr_inherit(slave_dev, master); +--- a/net/ethernet/eth.c ++++ b/net/ethernet/eth.c +@@ -506,13 +506,14 @@ unsigned char * __weak arch_get_platform + + int eth_platform_get_mac_address(struct device *dev, u8 *mac_addr) + { +- const unsigned char *addr = NULL; ++ unsigned char *addr; ++ int ret; + +- if (dev->of_node) +- addr = of_get_mac_address(dev->of_node); +- if (IS_ERR_OR_NULL(addr)) +- addr = arch_get_platform_mac_address(); ++ ret = of_get_mac_address(dev->of_node, mac_addr); ++ if (!ret) ++ return 0; + ++ addr = arch_get_platform_mac_address(); + if (!addr) + return -ENODEV; + diff --git a/target/linux/generic/backport-5.10/732-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch b/target/linux/generic/backport-5.10/732-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch new file mode 100644 index 0000000000..245c5f3bd6 --- /dev/null +++ b/target/linux/generic/backport-5.10/732-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch @@ -0,0 +1,77 @@ +From f10843e04a075202dbb39dfcee047e3a2fdf5a8d Mon Sep 17 00:00:00 2001 +From: Michael Walle +Date: Mon, 12 Apr 2021 19:47:18 +0200 +Subject: of: net: fix of_get_mac_addr_nvmem() for non-platform devices + +of_get_mac_address() already supports fetching the MAC address by an +nvmem provider. But until now, it was just working for platform devices. +Esp. it was not working for DSA ports and PCI devices. It gets more +common that PCI devices have a device tree binding since SoCs contain +integrated root complexes. + +Use the nvmem of_* binding to fetch the nvmem cells by a struct +device_node. We still have to try to read the cell by device first +because there might be a nvmem_cell_lookup associated with that device. + +Signed-off-by: Michael Walle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/of/of_net.c | 35 ++++++++++++++++++++++++++++++----- + 1 file changed, 30 insertions(+), 5 deletions(-) + +--- a/drivers/of/of_net.c ++++ b/drivers/of/of_net.c +@@ -11,6 +11,7 @@ + #include + #include + #include ++#include + + /** + * of_get_phy_mode - Get phy mode for given device_node +@@ -59,15 +60,39 @@ static int of_get_mac_addr(struct device + static int of_get_mac_addr_nvmem(struct device_node *np, u8 *addr) + { + struct platform_device *pdev = of_find_device_by_node(np); ++ struct nvmem_cell *cell; ++ const void *mac; ++ size_t len; + int ret; + +- if (!pdev) +- return -ENODEV; ++ /* Try lookup by device first, there might be a nvmem_cell_lookup ++ * associated with a given device. ++ */ ++ if (pdev) { ++ ret = nvmem_get_mac_address(&pdev->dev, addr); ++ put_device(&pdev->dev); ++ return ret; ++ } ++ ++ cell = of_nvmem_cell_get(np, "mac-address"); ++ if (IS_ERR(cell)) ++ return PTR_ERR(cell); ++ ++ mac = nvmem_cell_read(cell, &len); ++ nvmem_cell_put(cell); ++ ++ if (IS_ERR(mac)) ++ return PTR_ERR(mac); ++ ++ if (len != ETH_ALEN || !is_valid_ether_addr(mac)) { ++ kfree(mac); ++ return -EINVAL; ++ } + +- ret = nvmem_get_mac_address(&pdev->dev, addr); +- put_device(&pdev->dev); ++ memcpy(addr, mac, ETH_ALEN); ++ kfree(mac); + +- return ret; ++ return 0; + } + + /** diff --git a/target/linux/generic/backport-5.10/733-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch b/target/linux/generic/backport-5.10/733-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch new file mode 100644 index 0000000000..6e7f20634f --- /dev/null +++ b/target/linux/generic/backport-5.10/733-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch @@ -0,0 +1,42 @@ +From 029497e66bdc762e001880e4c85a91f35a54b1e2 Mon Sep 17 00:00:00 2001 +From: Christian Lamparter +Date: Sun, 19 Sep 2021 13:57:25 +0200 +Subject: [PATCH] net: bgmac-bcma: handle deferred probe error due to + mac-address +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Due to the inclusion of nvmem handling into the mac-address getter +function of_get_mac_address() by +commit d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") +it is now possible to get a -EPROBE_DEFER return code. Which did cause +bgmac to assign a random ethernet address. + +This exact issue happened on my Meraki MR32. The nvmem provider is +an EEPROM (at24c64) which gets instantiated once the module +driver is loaded... This happens once the filesystem becomes available. + +With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error. +Then the driver subsystem will reschedule the probe at a later time. + +Cc: Petr Å tetiar +Cc: Michael Walle +Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") +Signed-off-by: Christian Lamparter +Signed-off-by: David S. Miller +--- + drivers/net/ethernet/broadcom/bgmac-bcma.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c ++++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c +@@ -129,6 +129,8 @@ static int bgmac_probe(struct bcma_devic + bcma_set_drvdata(core, bgmac); + + err = of_get_mac_address(bgmac->dev->of_node, bgmac->net_dev->dev_addr); ++ if (err == -EPROBE_DEFER) ++ return err; + + /* If no MAC address assigned via device tree, check SPROM */ + if (err) { diff --git a/target/linux/generic/backport-5.10/733-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch b/target/linux/generic/backport-5.10/733-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch new file mode 100644 index 0000000000..bde62f3b1b --- /dev/null +++ b/target/linux/generic/backport-5.10/733-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch @@ -0,0 +1,36 @@ +From 763716a55cb1f480ffe1a9702e6b5d9ea1a80a24 Mon Sep 17 00:00:00 2001 +From: Matthew Hagan +Date: Sat, 25 Sep 2021 11:36:27 +0000 +Subject: [PATCH] net: bgmac-platform: handle mac-address deferral + +This patch is a replication of Christian Lamparter's "net: bgmac-bcma: +handle deferred probe error due to mac-address" patch for the +bgmac-platform driver [1]. + +As is the case with the bgmac-bcma driver, this change is to cover the +scenario where the MAC address cannot yet be discovered due to reliance +on an nvmem provider which is yet to be instantiated, resulting in a +random address being assigned that has to be manually overridden. + +[1] https://lore.kernel.org/netdev/20210919115725.29064-1-chunkeey@gmail.com + +Signed-off-by: Matthew Hagan +Reviewed-by: Andrew Lunn +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/ethernet/broadcom/bgmac-platform.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/net/ethernet/broadcom/bgmac-platform.c ++++ b/drivers/net/ethernet/broadcom/bgmac-platform.c +@@ -193,6 +193,9 @@ static int bgmac_probe(struct platform_d + bgmac->dma_dev = &pdev->dev; + + ret = of_get_mac_address(np, bgmac->net_dev->dev_addr); ++ if (ret == -EPROBE_DEFER) ++ return ret; ++ + if (ret) + dev_warn(&pdev->dev, + "MAC address not present in device tree\n"); diff --git a/target/linux/generic/backport-5.10/734-v5.16-0001-net-bgmac-improve-handling-PHY.patch b/target/linux/generic/backport-5.10/734-v5.16-0001-net-bgmac-improve-handling-PHY.patch new file mode 100644 index 0000000000..6788a2ec35 --- /dev/null +++ b/target/linux/generic/backport-5.10/734-v5.16-0001-net-bgmac-improve-handling-PHY.patch @@ -0,0 +1,84 @@ +From b5375509184dc23d2b7fa0c5ed8763899ccc9674 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sat, 2 Oct 2021 19:58:11 +0200 +Subject: [PATCH] net: bgmac: improve handling PHY +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +1. Use info from DT if available + +It allows describing for example a fixed link. It's more accurate than +just guessing there may be one (depending on a chipset). + +2. Verify PHY ID before trying to connect PHY + +PHY addr 0x1e (30) is special in Broadcom routers and means a switch +connected as MDIO devices instead of a real PHY. Don't try connecting to +it. + +Signed-off-by: Rafał Miłecki +Signed-off-by: David S. Miller +--- + drivers/net/ethernet/broadcom/bgmac-bcma.c | 33 ++++++++++++++-------- + 1 file changed, 21 insertions(+), 12 deletions(-) + +--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c ++++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c +@@ -11,6 +11,7 @@ + #include + #include + #include ++#include + #include + #include "bgmac.h" + +@@ -86,17 +87,28 @@ static int bcma_phy_connect(struct bgmac + struct phy_device *phy_dev; + char bus_id[MII_BUS_ID_SIZE + 3]; + ++ /* DT info should be the most accurate */ ++ phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node, ++ bgmac_adjust_link); ++ if (phy_dev) ++ return 0; ++ + /* Connect to the PHY */ +- snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id, +- bgmac->phyaddr); +- phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link, +- PHY_INTERFACE_MODE_MII); +- if (IS_ERR(phy_dev)) { +- dev_err(bgmac->dev, "PHY connection failed\n"); +- return PTR_ERR(phy_dev); ++ if (bgmac->mii_bus && bgmac->phyaddr != BGMAC_PHY_NOREGS) { ++ snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id, ++ bgmac->phyaddr); ++ phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link, ++ PHY_INTERFACE_MODE_MII); ++ if (IS_ERR(phy_dev)) { ++ dev_err(bgmac->dev, "PHY connection failed\n"); ++ return PTR_ERR(phy_dev); ++ } ++ ++ return 0; + } + +- return 0; ++ /* Assume a fixed link to the switch port */ ++ return bgmac_phy_connect_direct(bgmac); + } + + static const struct bcma_device_id bgmac_bcma_tbl[] = { +@@ -297,10 +309,7 @@ static int bgmac_probe(struct bcma_devic + bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset; + bgmac->get_bus_clock = bcma_bgmac_get_bus_clock; + bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32; +- if (bgmac->mii_bus) +- bgmac->phy_connect = bcma_phy_connect; +- else +- bgmac->phy_connect = bgmac_phy_connect_direct; ++ bgmac->phy_connect = bcma_phy_connect; + + err = bgmac_enet_probe(bgmac); + if (err) diff --git a/target/linux/generic/backport-5.10/734-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch b/target/linux/generic/backport-5.10/734-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch new file mode 100644 index 0000000000..f134828273 --- /dev/null +++ b/target/linux/generic/backport-5.10/734-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch @@ -0,0 +1,54 @@ +From 45c9d966688e7fad7f24bfc450547d91e4304d0b Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Sat, 2 Oct 2021 19:58:12 +0200 +Subject: [PATCH] net: bgmac: support MDIO described in DT +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Check ethernet controller DT node for "mdio" subnode and use it with +of_mdiobus_register() when present. That allows specifying MDIO and its +PHY devices in a standard DT based way. + +This is required for BCM53573 SoC support. That family is sometimes +called Northstar (by marketing?) but is quite different from it. It uses +different CPU(s) and many different hw blocks. + +One of shared blocks in BCM53573 is Ethernet controller. Switch however +is not SRAB accessible (as it Northstar) but is MDIO attached. + +Signed-off-by: Rafał Miłecki +Signed-off-by: David S. Miller +--- + drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c ++++ b/drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c +@@ -10,6 +10,7 @@ + + #include + #include ++#include + #include "bgmac.h" + + static bool bcma_mdio_wait_value(struct bcma_device *core, u16 reg, u32 mask, +@@ -211,6 +212,7 @@ struct mii_bus *bcma_mdio_mii_register(s + { + struct bcma_device *core = bgmac->bcma.core; + struct mii_bus *mii_bus; ++ struct device_node *np; + int err; + + mii_bus = mdiobus_alloc(); +@@ -229,7 +231,9 @@ struct mii_bus *bcma_mdio_mii_register(s + mii_bus->parent = &core->dev; + mii_bus->phy_mask = ~(1 << bgmac->phyaddr); + +- err = mdiobus_register(mii_bus); ++ np = of_get_child_by_name(core->dev.of_node, "mdio"); ++ ++ err = of_mdiobus_register(mii_bus, np); + if (err) { + dev_err(&core->dev, "Registration of mii bus failed\n"); + goto err_free_bus; diff --git a/target/linux/generic/backport-5.10/735-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch b/target/linux/generic/backport-5.10/735-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch new file mode 100644 index 0000000000..b8e6d9b613 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch @@ -0,0 +1,35 @@ +From 5d9e068402dcf7354cc8ee66c2152845306d2ccb Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:51 +0200 +Subject: [PATCH] net: dsa: qca8k: change simple print to dev variant + +Change pr_err and pr_warn to dev variant. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -701,7 +701,7 @@ qca8k_setup(struct dsa_switch *ds) + + /* Make sure that port 0 is the cpu port */ + if (!dsa_is_cpu_port(ds, 0)) { +- pr_err("port 0 is not the CPU port\n"); ++ dev_err(priv->dev, "port 0 is not the CPU port"); + return -EINVAL; + } + +@@ -711,7 +711,7 @@ qca8k_setup(struct dsa_switch *ds) + priv->regmap = devm_regmap_init(ds->dev, NULL, priv, + &qca8k_regmap_config); + if (IS_ERR(priv->regmap)) +- pr_warn("regmap initialization failed"); ++ dev_warn(priv->dev, "regmap initialization failed"); + + ret = qca8k_setup_mdio_bus(priv); + if (ret) diff --git a/target/linux/generic/backport-5.10/735-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch b/target/linux/generic/backport-5.10/735-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch new file mode 100644 index 0000000000..ff8288d484 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch @@ -0,0 +1,61 @@ +From 2ad255f2faaffb3af786031fba2e7955454b558a Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:52 +0200 +Subject: [PATCH] net: dsa: qca8k: use iopoll macro for qca8k_busy_wait + +Use iopoll macro instead of while loop. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 23 +++++++++++------------ + drivers/net/dsa/qca8k.h | 2 ++ + 2 files changed, 13 insertions(+), 12 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -262,21 +262,20 @@ static struct regmap_config qca8k_regmap + static int + qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) + { +- unsigned long timeout; ++ u32 val; ++ int ret; + +- timeout = jiffies + msecs_to_jiffies(20); ++ ret = read_poll_timeout(qca8k_read, val, !(val & mask), ++ 0, QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, ++ priv, reg); + +- /* loop until the busy flag has cleared */ +- do { +- u32 val = qca8k_read(priv, reg); +- int busy = val & mask; ++ /* Check if qca8k_read has failed for a different reason ++ * before returning -ETIMEDOUT ++ */ ++ if (ret < 0 && val < 0) ++ return val; + +- if (!busy) +- break; +- cond_resched(); +- } while (!time_after_eq(jiffies, timeout)); +- +- return time_after_eq(jiffies, timeout); ++ return ret; + } + + static void +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -18,6 +18,8 @@ + #define PHY_ID_QCA8337 0x004dd036 + #define QCA8K_ID_QCA8337 0x13 + ++#define QCA8K_BUSY_WAIT_TIMEOUT 20 ++ + #define QCA8K_NUM_FDB_RECORDS 2048 + + #define QCA8K_CPU_PORT 0 diff --git a/target/linux/generic/backport-5.10/735-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch b/target/linux/generic/backport-5.10/735-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch new file mode 100644 index 0000000000..c403589874 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch @@ -0,0 +1,86 @@ +From 504bf65931824eda83494e5b5d75686e27ace03e Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:53 +0200 +Subject: [PATCH] net: dsa: qca8k: improve qca8k read/write/rmw bus access + +Put bus in local variable to improve faster access to the mdio bus. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 29 ++++++++++++++++------------- + 1 file changed, 16 insertions(+), 13 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -142,17 +142,18 @@ qca8k_set_page(struct mii_bus *bus, u16 + static u32 + qca8k_read(struct qca8k_priv *priv, u32 reg) + { ++ struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 val; + + qca8k_split_addr(reg, &r1, &r2, &page); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(priv->bus, page); +- val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); ++ qca8k_set_page(bus, page); ++ val = qca8k_mii_read32(bus, 0x10 | r2, r1); + +- mutex_unlock(&priv->bus->mdio_lock); ++ mutex_unlock(&bus->mdio_lock); + + return val; + } +@@ -160,35 +161,37 @@ qca8k_read(struct qca8k_priv *priv, u32 + static void + qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) + { ++ struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + + qca8k_split_addr(reg, &r1, &r2, &page); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(priv->bus, page); +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); ++ qca8k_set_page(bus, page); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, val); + +- mutex_unlock(&priv->bus->mdio_lock); ++ mutex_unlock(&bus->mdio_lock); + } + + static u32 + qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 val) + { ++ struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 ret; + + qca8k_split_addr(reg, &r1, &r2, &page); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(priv->bus, page); +- ret = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); ++ qca8k_set_page(bus, page); ++ ret = qca8k_mii_read32(bus, 0x10 | r2, r1); + ret &= ~mask; + ret |= val; +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, ret); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, ret); + +- mutex_unlock(&priv->bus->mdio_lock); ++ mutex_unlock(&bus->mdio_lock); + + return ret; + } diff --git a/target/linux/generic/backport-5.10/735-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch b/target/linux/generic/backport-5.10/735-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch new file mode 100644 index 0000000000..6be494a8c7 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch @@ -0,0 +1,101 @@ +From ba5707ec58cfb6853dff41c2aae72deb6a03d389 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:54 +0200 +Subject: [PATCH] net: dsa: qca8k: handle qca8k_set_page errors + +With a remote possibility, the set_page function can fail. Since this is +a critical part of the write/read qca8k regs, propagate the error and +terminate any read/write operation. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 33 ++++++++++++++++++++++++++------- + 1 file changed, 26 insertions(+), 7 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -127,16 +127,23 @@ qca8k_mii_write32(struct mii_bus *bus, i + "failed to write qca8k 32bit register\n"); + } + +-static void ++static int + qca8k_set_page(struct mii_bus *bus, u16 page) + { ++ int ret; ++ + if (page == qca8k_current_page) +- return; ++ return 0; + +- if (bus->write(bus, 0x18, 0, page) < 0) ++ ret = bus->write(bus, 0x18, 0, page); ++ if (ret < 0) { + dev_err_ratelimited(&bus->dev, + "failed to set qca8k page\n"); ++ return ret; ++ } ++ + qca8k_current_page = page; ++ return 0; + } + + static u32 +@@ -150,11 +157,14 @@ qca8k_read(struct qca8k_priv *priv, u32 + + mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(bus, page); ++ val = qca8k_set_page(bus, page); ++ if (val < 0) ++ goto exit; ++ + val = qca8k_mii_read32(bus, 0x10 | r2, r1); + ++exit: + mutex_unlock(&bus->mdio_lock); +- + return val; + } + +@@ -163,14 +173,19 @@ qca8k_write(struct qca8k_priv *priv, u32 + { + struct mii_bus *bus = priv->bus; + u16 r1, r2, page; ++ int ret; + + qca8k_split_addr(reg, &r1, &r2, &page); + + mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(bus, page); ++ ret = qca8k_set_page(bus, page); ++ if (ret < 0) ++ goto exit; ++ + qca8k_mii_write32(bus, 0x10 | r2, r1, val); + ++exit: + mutex_unlock(&bus->mdio_lock); + } + +@@ -185,12 +200,16 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r + + mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- qca8k_set_page(bus, page); ++ ret = qca8k_set_page(bus, page); ++ if (ret < 0) ++ goto exit; ++ + ret = qca8k_mii_read32(bus, 0x10 | r2, r1); + ret &= ~mask; + ret |= val; + qca8k_mii_write32(bus, 0x10 | r2, r1, ret); + ++exit: + mutex_unlock(&bus->mdio_lock); + + return ret; diff --git a/target/linux/generic/backport-5.10/735-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch b/target/linux/generic/backport-5.10/735-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch new file mode 100644 index 0000000000..3349b7897a --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch @@ -0,0 +1,207 @@ +From 028f5f8ef44fcf87a456772cbb9f0d90a0a22884 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:55 +0200 +Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_read operation + +qca8k_read can fail. Rework any user to handle error values and +correctly return. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 73 ++++++++++++++++++++++++++++++++--------- + 1 file changed, 58 insertions(+), 15 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -231,8 +231,13 @@ static int + qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ctx; ++ int ret; ++ ++ ret = qca8k_read(priv, reg); ++ if (ret < 0) ++ return ret; + +- *val = qca8k_read(priv, reg); ++ *val = ret; + + return 0; + } +@@ -300,15 +305,20 @@ qca8k_busy_wait(struct qca8k_priv *priv, + return ret; + } + +-static void ++static int + qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) + { +- u32 reg[4]; ++ u32 reg[4], val; + int i; + + /* load the ARL table into an array */ +- for (i = 0; i < 4; i++) +- reg[i] = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); ++ for (i = 0; i < 4; i++) { ++ val = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); ++ if (val < 0) ++ return val; ++ ++ reg[i] = val; ++ } + + /* vid - 83:72 */ + fdb->vid = (reg[2] >> QCA8K_ATU_VID_S) & QCA8K_ATU_VID_M; +@@ -323,6 +333,8 @@ qca8k_fdb_read(struct qca8k_priv *priv, + fdb->mac[3] = (reg[0] >> QCA8K_ATU_ADDR3_S) & 0xff; + fdb->mac[4] = (reg[0] >> QCA8K_ATU_ADDR4_S) & 0xff; + fdb->mac[5] = reg[0] & 0xff; ++ ++ return 0; + } + + static void +@@ -374,6 +386,8 @@ qca8k_fdb_access(struct qca8k_priv *priv + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_FDB_LOAD) { + reg = qca8k_read(priv, QCA8K_REG_ATU_FUNC); ++ if (reg < 0) ++ return reg; + if (reg & QCA8K_ATU_FUNC_FULL) + return -1; + } +@@ -388,10 +402,10 @@ qca8k_fdb_next(struct qca8k_priv *priv, + + qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging); + ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port); +- if (ret >= 0) +- qca8k_fdb_read(priv, fdb); ++ if (ret < 0) ++ return ret; + +- return ret; ++ return qca8k_fdb_read(priv, fdb); + } + + static int +@@ -449,6 +463,8 @@ qca8k_vlan_access(struct qca8k_priv *pri + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_VLAN_LOAD) { + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1); ++ if (reg < 0) ++ return reg; + if (reg & QCA8K_VTU_FUNC1_FULL) + return -ENOMEM; + } +@@ -475,6 +491,8 @@ qca8k_vlan_add(struct qca8k_priv *priv, + goto out; + + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); ++ if (reg < 0) ++ return reg; + reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; + reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + if (untagged) +@@ -506,6 +524,8 @@ qca8k_vlan_del(struct qca8k_priv *priv, + goto out; + + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); ++ if (reg < 0) ++ return reg; + reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << + QCA8K_VTU_FUNC0_EG_MODE_S(port); +@@ -621,8 +641,11 @@ qca8k_mdio_read(struct qca8k_priv *priv, + QCA8K_MDIO_MASTER_BUSY)) + return -ETIMEDOUT; + +- val = (qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL) & +- QCA8K_MDIO_MASTER_DATA_MASK); ++ val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); ++ if (val < 0) ++ return val; ++ ++ val &= QCA8K_MDIO_MASTER_DATA_MASK; + + return val; + } +@@ -978,6 +1001,8 @@ qca8k_phylink_mac_link_state(struct dsa_ + u32 reg; + + reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port)); ++ if (reg < 0) ++ return reg; + + state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); + state->an_complete = state->link; +@@ -1078,18 +1103,26 @@ qca8k_get_ethtool_stats(struct dsa_switc + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + const struct qca8k_mib_desc *mib; +- u32 reg, i; ++ u32 reg, i, val; + u64 hi; + + for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { + mib = &ar8327_mib[i]; + reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; + +- data[i] = qca8k_read(priv, reg); ++ val = qca8k_read(priv, reg); ++ if (val < 0) ++ continue; ++ + if (mib->size == 2) { + hi = qca8k_read(priv, reg + 4); +- data[i] |= hi << 32; ++ if (hi < 0) ++ continue; + } ++ ++ data[i] = val; ++ if (mib->size == 2) ++ data[i] |= hi << 32; + } + } + +@@ -1107,18 +1140,25 @@ qca8k_set_mac_eee(struct dsa_switch *ds, + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); ++ int ret = 0; + u32 reg; + + mutex_lock(&priv->reg_mutex); + reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); ++ if (reg < 0) { ++ ret = reg; ++ goto exit; ++ } ++ + if (eee->eee_enabled) + reg |= lpi_en; + else + reg &= ~lpi_en; + qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); +- mutex_unlock(&priv->reg_mutex); + +- return 0; ++exit: ++ mutex_unlock(&priv->reg_mutex); ++ return ret; + } + + static int +@@ -1456,6 +1496,9 @@ qca8k_sw_probe(struct mdio_device *mdiod + + /* read the switches ID register */ + id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); ++ if (id < 0) ++ return id; ++ + id >>= QCA8K_MASK_CTRL_ID_S; + id &= QCA8K_MASK_CTRL_ID_M; + if (id != QCA8K_ID_QCA8337) diff --git a/target/linux/generic/backport-5.10/735-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch b/target/linux/generic/backport-5.10/735-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch new file mode 100644 index 0000000000..1e0e224c39 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch @@ -0,0 +1,263 @@ +From d7805757c75c76e9518fc1023a29f0c4eed5b581 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:56 +0200 +Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_write operation + +qca8k_write can fail. Rework any user to handle error values and +correctly return. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 102 ++++++++++++++++++++++++++-------------- + 1 file changed, 67 insertions(+), 35 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -168,7 +168,7 @@ exit: + return val; + } + +-static void ++static int + qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) + { + struct mii_bus *bus = priv->bus; +@@ -187,6 +187,7 @@ qca8k_write(struct qca8k_priv *priv, u32 + + exit: + mutex_unlock(&bus->mdio_lock); ++ return ret; + } + + static u32 +@@ -247,9 +248,7 @@ qca8k_regmap_write(void *ctx, uint32_t r + { + struct qca8k_priv *priv = (struct qca8k_priv *)ctx; + +- qca8k_write(priv, reg, val); +- +- return 0; ++ return qca8k_write(priv, reg, val); + } + + static const struct regmap_range qca8k_readable_ranges[] = { +@@ -367,6 +366,7 @@ static int + qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port) + { + u32 reg; ++ int ret; + + /* Set the command and FDB index */ + reg = QCA8K_ATU_FUNC_BUSY; +@@ -377,7 +377,9 @@ qca8k_fdb_access(struct qca8k_priv *priv + } + + /* Write the function register triggering the table access */ +- qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); ++ ret = qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); ++ if (ret) ++ return ret; + + /* wait for completion */ + if (qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY)) +@@ -447,6 +449,7 @@ static int + qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid) + { + u32 reg; ++ int ret; + + /* Set the command and VLAN index */ + reg = QCA8K_VTU_FUNC1_BUSY; +@@ -454,7 +457,9 @@ qca8k_vlan_access(struct qca8k_priv *pri + reg |= vid << QCA8K_VTU_FUNC1_VID_S; + + /* Write the function register triggering the table access */ +- qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); ++ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); ++ if (ret) ++ return ret; + + /* wait for completion */ + if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY)) +@@ -502,7 +507,9 @@ qca8k_vlan_add(struct qca8k_priv *priv, + reg |= QCA8K_VTU_FUNC0_EG_MODE_TAG << + QCA8K_VTU_FUNC0_EG_MODE_S(port); + +- qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); ++ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); ++ if (ret) ++ return ret; + ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); + + out: +@@ -545,7 +552,9 @@ qca8k_vlan_del(struct qca8k_priv *priv, + if (del) { + ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid); + } else { +- qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); ++ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); ++ if (ret) ++ return ret; + ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); + } + +@@ -555,15 +564,20 @@ out: + return ret; + } + +-static void ++static int + qca8k_mib_init(struct qca8k_priv *priv) + { ++ int ret; ++ + mutex_lock(&priv->reg_mutex); + qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); + qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); + qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); +- qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); ++ ++ ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); ++ + mutex_unlock(&priv->reg_mutex); ++ return ret; + } + + static void +@@ -600,6 +614,7 @@ static int + qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) + { + u32 phy, val; ++ int ret; + + if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) + return -EINVAL; +@@ -613,7 +628,9 @@ qca8k_mdio_write(struct qca8k_priv *priv + QCA8K_MDIO_MASTER_REG_ADDR(regnum) | + QCA8K_MDIO_MASTER_DATA(data); + +- qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); ++ ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); ++ if (ret) ++ return ret; + + return qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY); +@@ -623,6 +640,7 @@ static int + qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) + { + u32 phy, val; ++ int ret; + + if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) + return -EINVAL; +@@ -635,7 +653,9 @@ qca8k_mdio_read(struct qca8k_priv *priv, + QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | + QCA8K_MDIO_MASTER_REG_ADDR(regnum); + +- qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); ++ ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); ++ if (ret) ++ return ret; + + if (qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY)) +@@ -766,12 +786,18 @@ qca8k_setup(struct dsa_switch *ds) + QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); + + /* Enable MIB counters */ +- qca8k_mib_init(priv); ++ ret = qca8k_mib_init(priv); ++ if (ret) ++ dev_warn(priv->dev, "mib init failed"); + + /* Enable QCA header mode on the cpu port */ +- qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), +- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | +- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); ++ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), ++ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | ++ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); ++ if (ret) { ++ dev_err(priv->dev, "failed enabling QCA header mode"); ++ return ret; ++ } + + /* Disable forwarding by default on all ports */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) +@@ -783,11 +809,13 @@ qca8k_setup(struct dsa_switch *ds) + qca8k_port_set_status(priv, i, 0); + + /* Forward all unknown frames to CPU port for Linux processing */ +- qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); ++ ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, ++ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | ++ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | ++ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | ++ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); ++ if (ret) ++ return ret; + + /* Setup connection between CPU port & user ports */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) { +@@ -815,16 +843,20 @@ qca8k_setup(struct dsa_switch *ds) + qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), + 0xfff << shift, + QCA8K_PORT_VID_DEF << shift); +- qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), +- QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | +- QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); ++ ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), ++ QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | ++ QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); ++ if (ret) ++ return ret; + } + } + + /* Setup our port MTUs to match power on defaults */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) + priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; +- qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); ++ ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); ++ if (ret) ++ dev_warn(priv->dev, "failed setting MTU settings"); + + /* Flush the FDB table */ + qca8k_fdb_flush(priv); +@@ -1140,8 +1172,8 @@ qca8k_set_mac_eee(struct dsa_switch *ds, + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); +- int ret = 0; + u32 reg; ++ int ret; + + mutex_lock(&priv->reg_mutex); + reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); +@@ -1154,7 +1186,7 @@ qca8k_set_mac_eee(struct dsa_switch *ds, + reg |= lpi_en; + else + reg &= ~lpi_en; +- qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); ++ ret = qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); + + exit: + mutex_unlock(&priv->reg_mutex); +@@ -1284,9 +1316,7 @@ qca8k_port_change_mtu(struct dsa_switch + mtu = priv->port_mtu[i]; + + /* Include L2 header / FCS length */ +- qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); +- +- return 0; ++ return qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); + } + + static int diff --git a/target/linux/generic/backport-5.10/735-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch b/target/linux/generic/backport-5.10/735-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch new file mode 100644 index 0000000000..506966f1af --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch @@ -0,0 +1,226 @@ +From aaf421425cbdec4eb6fd75a29e65c2867b0b7bbd Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:57 +0200 +Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_rmw operation + +qca8k_rmw can fail. Rework any user to handle error values and +correctly return. Change qca8k_rmw to return the error code or 0 instead +of the reg value. The reg returned by qca8k_rmw wasn't used anywhere, +so this doesn't cause any functional change. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 133 +++++++++++++++++++++++++--------------- + 1 file changed, 83 insertions(+), 50 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -190,12 +190,13 @@ exit: + return ret; + } + +-static u32 +-qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 val) ++static int ++qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val) + { + struct mii_bus *bus = priv->bus; + u16 r1, r2, page; +- u32 ret; ++ u32 val; ++ int ret; + + qca8k_split_addr(reg, &r1, &r2, &page); + +@@ -205,10 +206,15 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r + if (ret < 0) + goto exit; + +- ret = qca8k_mii_read32(bus, 0x10 | r2, r1); +- ret &= ~mask; +- ret |= val; +- qca8k_mii_write32(bus, 0x10 | r2, r1, ret); ++ val = qca8k_mii_read32(bus, 0x10 | r2, r1); ++ if (val < 0) { ++ ret = val; ++ goto exit; ++ } ++ ++ val &= ~mask; ++ val |= write_val; ++ qca8k_mii_write32(bus, 0x10 | r2, r1, val); + + exit: + mutex_unlock(&bus->mdio_lock); +@@ -216,16 +222,16 @@ exit: + return ret; + } + +-static void ++static int + qca8k_reg_set(struct qca8k_priv *priv, u32 reg, u32 val) + { +- qca8k_rmw(priv, reg, 0, val); ++ return qca8k_rmw(priv, reg, 0, val); + } + +-static void ++static int + qca8k_reg_clear(struct qca8k_priv *priv, u32 reg, u32 val) + { +- qca8k_rmw(priv, reg, val, 0); ++ return qca8k_rmw(priv, reg, val, 0); + } + + static int +@@ -570,12 +576,19 @@ qca8k_mib_init(struct qca8k_priv *priv) + int ret; + + mutex_lock(&priv->reg_mutex); +- qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); ++ ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); ++ if (ret) ++ goto exit; ++ + qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); +- qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); ++ ++ ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); ++ if (ret) ++ goto exit; + + ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); + ++exit: + mutex_unlock(&priv->reg_mutex); + return ret; + } +@@ -747,9 +760,8 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + * a dt-overlay and driver reload changed the configuration + */ + +- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_EN); +- return 0; ++ return qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_EN); + } + + priv->ops.phy_read = qca8k_phy_read; +@@ -782,8 +794,12 @@ qca8k_setup(struct dsa_switch *ds) + return ret; + + /* Enable CPU Port */ +- qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, +- QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); ++ ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, ++ QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); ++ if (ret) { ++ dev_err(priv->dev, "failed enabling CPU port"); ++ return ret; ++ } + + /* Enable MIB counters */ + ret = qca8k_mib_init(priv); +@@ -800,9 +816,12 @@ qca8k_setup(struct dsa_switch *ds) + } + + /* Disable forwarding by default on all ports */ +- for (i = 0; i < QCA8K_NUM_PORTS; i++) +- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), +- QCA8K_PORT_LOOKUP_MEMBER, 0); ++ for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), ++ QCA8K_PORT_LOOKUP_MEMBER, 0); ++ if (ret) ++ return ret; ++ } + + /* Disable MAC by default on all ports */ + for (i = 1; i < QCA8K_NUM_PORTS; i++) +@@ -821,28 +840,37 @@ qca8k_setup(struct dsa_switch *ds) + for (i = 0; i < QCA8K_NUM_PORTS; i++) { + /* CPU port gets connected to all user ports of the switch */ + if (dsa_is_cpu_port(ds, i)) { +- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), +- QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), ++ QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); ++ if (ret) ++ return ret; + } + + /* Individual user ports get connected to CPU port only */ + if (dsa_is_user_port(ds, i)) { + int shift = 16 * (i % 2); + +- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), +- QCA8K_PORT_LOOKUP_MEMBER, +- BIT(QCA8K_CPU_PORT)); ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), ++ QCA8K_PORT_LOOKUP_MEMBER, ++ BIT(QCA8K_CPU_PORT)); ++ if (ret) ++ return ret; + + /* Enable ARP Auto-learning by default */ +- qca8k_reg_set(priv, QCA8K_PORT_LOOKUP_CTRL(i), +- QCA8K_PORT_LOOKUP_LEARN); ++ ret = qca8k_reg_set(priv, QCA8K_PORT_LOOKUP_CTRL(i), ++ QCA8K_PORT_LOOKUP_LEARN); ++ if (ret) ++ return ret; + + /* For port based vlans to work we need to set the + * default egress vid + */ +- qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), +- 0xfff << shift, +- QCA8K_PORT_VID_DEF << shift); ++ ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), ++ 0xfff << shift, ++ QCA8K_PORT_VID_DEF << shift); ++ if (ret) ++ return ret; ++ + ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), + QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | + QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); +@@ -1234,7 +1262,7 @@ qca8k_port_bridge_join(struct dsa_switch + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + int port_mask = BIT(QCA8K_CPU_PORT); +- int i; ++ int i, ret; + + for (i = 1; i < QCA8K_NUM_PORTS; i++) { + if (dsa_to_port(ds, i)->bridge_dev != br) +@@ -1242,17 +1270,20 @@ qca8k_port_bridge_join(struct dsa_switch + /* Add this port to the portvlan mask of the other ports + * in the bridge + */ +- qca8k_reg_set(priv, +- QCA8K_PORT_LOOKUP_CTRL(i), +- BIT(port)); ++ ret = qca8k_reg_set(priv, ++ QCA8K_PORT_LOOKUP_CTRL(i), ++ BIT(port)); ++ if (ret) ++ return ret; + if (i != port) + port_mask |= BIT(i); + } ++ + /* Add all other ports to this ports portvlan mask */ +- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), +- QCA8K_PORT_LOOKUP_MEMBER, port_mask); ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), ++ QCA8K_PORT_LOOKUP_MEMBER, port_mask); + +- return 0; ++ return ret; + } + + static void diff --git a/target/linux/generic/backport-5.10/735-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch b/target/linux/generic/backport-5.10/735-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch new file mode 100644 index 0000000000..360ce1d947 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch @@ -0,0 +1,66 @@ +From b7c818d194927bdc60ed15db55bb8654496a36b7 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:58 +0200 +Subject: [PATCH] net: dsa: qca8k: handle error from qca8k_busy_wait + +Propagate errors from qca8k_busy_wait instead of hardcoding return +value. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 21 +++++++++++++-------- + 1 file changed, 13 insertions(+), 8 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -388,8 +388,9 @@ qca8k_fdb_access(struct qca8k_priv *priv + return ret; + + /* wait for completion */ +- if (qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY)) +- return -1; ++ ret = qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY); ++ if (ret) ++ return ret; + + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_FDB_LOAD) { +@@ -468,8 +469,9 @@ qca8k_vlan_access(struct qca8k_priv *pri + return ret; + + /* wait for completion */ +- if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY)) +- return -ETIMEDOUT; ++ ret = qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY); ++ if (ret) ++ return ret; + + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_VLAN_LOAD) { +@@ -580,7 +582,9 @@ qca8k_mib_init(struct qca8k_priv *priv) + if (ret) + goto exit; + +- qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); ++ ret = qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); ++ if (ret) ++ goto exit; + + ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); + if (ret) +@@ -670,9 +674,10 @@ qca8k_mdio_read(struct qca8k_priv *priv, + if (ret) + return ret; + +- if (qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_BUSY)) +- return -ETIMEDOUT; ++ ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_BUSY); ++ if (ret) ++ return ret; + + val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); + if (val < 0) diff --git a/target/linux/generic/backport-5.10/735-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch b/target/linux/generic/backport-5.10/735-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch new file mode 100644 index 0000000000..72305850ca --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch @@ -0,0 +1,96 @@ +From 6e82a457e06252b59102486767539cc9c2aba60b Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 22:59:59 +0200 +Subject: [PATCH] net: dsa: qca8k: add support for qca8327 switch + +qca8327 switch is a low tier version of the more recent qca8337. +It does share the same regs used by the qca8k driver and can be +supported with minimal change. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Reviewed-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 23 ++++++++++++++++++++--- + drivers/net/dsa/qca8k.h | 6 ++++++ + 2 files changed, 26 insertions(+), 3 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1533,6 +1533,7 @@ static const struct dsa_switch_ops qca8k + static int + qca8k_sw_probe(struct mdio_device *mdiodev) + { ++ const struct qca8k_match_data *data; + struct qca8k_priv *priv; + u32 id; + +@@ -1560,6 +1561,11 @@ qca8k_sw_probe(struct mdio_device *mdiod + gpiod_set_value_cansleep(priv->reset_gpio, 0); + } + ++ /* get the switches ID from the compatible */ ++ data = of_device_get_match_data(&mdiodev->dev); ++ if (!data) ++ return -ENODEV; ++ + /* read the switches ID register */ + id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); + if (id < 0) +@@ -1567,8 +1573,10 @@ qca8k_sw_probe(struct mdio_device *mdiod + + id >>= QCA8K_MASK_CTRL_ID_S; + id &= QCA8K_MASK_CTRL_ID_M; +- if (id != QCA8K_ID_QCA8337) ++ if (id != data->id) { ++ dev_err(&mdiodev->dev, "Switch id detected %x but expected %x", id, data->id); + return -ENODEV; ++ } + + priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); + if (!priv->ds) +@@ -1634,9 +1642,18 @@ static int qca8k_resume(struct device *d + static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, + qca8k_suspend, qca8k_resume); + ++static const struct qca8k_match_data qca832x = { ++ .id = QCA8K_ID_QCA8327, ++}; ++ ++static const struct qca8k_match_data qca833x = { ++ .id = QCA8K_ID_QCA8337, ++}; ++ + static const struct of_device_id qca8k_of_match[] = { +- { .compatible = "qca,qca8334" }, +- { .compatible = "qca,qca8337" }, ++ { .compatible = "qca,qca8327", .data = &qca832x }, ++ { .compatible = "qca,qca8334", .data = &qca833x }, ++ { .compatible = "qca,qca8337", .data = &qca833x }, + { /* sentinel */ }, + }; + +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -15,6 +15,8 @@ + #define QCA8K_NUM_PORTS 7 + #define QCA8K_MAX_MTU 9000 + ++#define PHY_ID_QCA8327 0x004dd034 ++#define QCA8K_ID_QCA8327 0x12 + #define PHY_ID_QCA8337 0x004dd036 + #define QCA8K_ID_QCA8337 0x13 + +@@ -213,6 +215,10 @@ struct ar8xxx_port_status { + int enabled; + }; + ++struct qca8k_match_data { ++ u8 id; ++}; ++ + struct qca8k_priv { + struct regmap *regmap; + struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/735-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch b/target/linux/generic/backport-5.10/735-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch new file mode 100644 index 0000000000..3c4a14bd0b --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch @@ -0,0 +1,26 @@ +From 227a9ffc1bc77037339530607fe129af3824620e Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:00 +0200 +Subject: [PATCH] devicetree: net: dsa: qca8k: Document new compatible qca8327 + +Add support for qca8327 in the compatible list. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Acked-by: Rob Herring +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 1 + + 1 file changed, 1 insertion(+) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -3,6 +3,7 @@ + Required properties: + + - compatible: should be one of: ++ "qca,qca8327" + "qca,qca8334" + "qca,qca8337" + diff --git a/target/linux/generic/backport-5.10/735-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch b/target/linux/generic/backport-5.10/735-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch new file mode 100644 index 0000000000..cd3050ef71 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch @@ -0,0 +1,130 @@ +From 83a3ceb39b2495171aabe9446271b94c678354f3 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:01 +0200 +Subject: [PATCH] net: dsa: qca8k: add priority tweak to qca8337 switch + +The port 5 of the qca8337 have some problem in flood condition. The +original legacy driver had some specific buffer and priority settings +for the different port suggested by the QCA switch team. Add this +missing settings to improve switch stability under load condition. +The packet priority tweak is only needed for the qca8337 switch and +other qca8k switch are not affected. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 47 +++++++++++++++++++++++++++++++++++++++++ + drivers/net/dsa/qca8k.h | 25 ++++++++++++++++++++++ + 2 files changed, 72 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -779,6 +779,7 @@ qca8k_setup(struct dsa_switch *ds) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + int ret, i; ++ u32 mask; + + /* Make sure that port 0 is the cpu port */ + if (!dsa_is_cpu_port(ds, 0)) { +@@ -884,6 +885,51 @@ qca8k_setup(struct dsa_switch *ds) + } + } + ++ /* The port 5 of the qca8337 have some problem in flood condition. The ++ * original legacy driver had some specific buffer and priority settings ++ * for the different port suggested by the QCA switch team. Add this ++ * missing settings to improve switch stability under load condition. ++ * This problem is limited to qca8337 and other qca8k switch are not affected. ++ */ ++ if (priv->switch_id == QCA8K_ID_QCA8337) { ++ for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ switch (i) { ++ /* The 2 CPU port and port 5 requires some different ++ * priority than any other ports. ++ */ ++ case 0: ++ case 5: ++ case 6: ++ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) | ++ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e); ++ break; ++ default: ++ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) | ++ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) | ++ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19); ++ } ++ qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask); ++ ++ mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) | ++ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | ++ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | ++ QCA8K_PORT_HOL_CTRL1_WRED_EN; ++ qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i), ++ QCA8K_PORT_HOL_CTRL1_ING_BUF | ++ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | ++ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | ++ QCA8K_PORT_HOL_CTRL1_WRED_EN, ++ mask); ++ } ++ } ++ + /* Setup our port MTUs to match power on defaults */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) + priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; +@@ -1578,6 +1624,7 @@ qca8k_sw_probe(struct mdio_device *mdiod + return -ENODEV; + } + ++ priv->switch_id = id; + priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); + if (!priv->ds) + return -ENOMEM; +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -168,6 +168,30 @@ + #define QCA8K_PORT_LOOKUP_STATE GENMASK(18, 16) + #define QCA8K_PORT_LOOKUP_LEARN BIT(20) + ++#define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF GENMASK(3, 0) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) ((x) << 0) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF GENMASK(7, 4) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI1(x) ((x) << 4) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF GENMASK(11, 8) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI2(x) ((x) << 8) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF GENMASK(15, 12) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI3(x) ((x) << 12) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF GENMASK(19, 16) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI4(x) ((x) << 16) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF GENMASK(23, 20) ++#define QCA8K_PORT_HOL_CTRL0_EG_PRI5(x) ((x) << 20) ++#define QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF GENMASK(29, 24) ++#define QCA8K_PORT_HOL_CTRL0_EG_PORT(x) ((x) << 24) ++ ++#define QCA8K_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8) ++#define QCA8K_PORT_HOL_CTRL1_ING_BUF GENMASK(3, 0) ++#define QCA8K_PORT_HOL_CTRL1_ING(x) ((x) << 0) ++#define QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6) ++#define QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7) ++#define QCA8K_PORT_HOL_CTRL1_WRED_EN BIT(8) ++#define QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16) ++ + /* Pkt edit registers */ + #define QCA8K_EGRESS_VLAN(x) (0x0c70 + (4 * (x / 2))) + +@@ -220,6 +244,7 @@ struct qca8k_match_data { + }; + + struct qca8k_priv { ++ u8 switch_id; + struct regmap *regmap; + struct mii_bus *bus; + struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/735-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch b/target/linux/generic/backport-5.10/735-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch new file mode 100644 index 0000000000..d25edbb1aa --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch @@ -0,0 +1,31 @@ +From 5bf9ff3b9fb5ecb67a1a3517b26db3a00f2a2f11 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:02 +0200 +Subject: [PATCH] net: dsa: qca8k: limit port5 delay to qca8337 + +Limit port5 rx delay to qca8337. This is taken from the legacy QSDK code +that limits the rx delay on port5 to only this particular switch version, +on other switch only the tx and rx delay for port0 are needed. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1003,8 +1003,10 @@ qca8k_phylink_mac_config(struct dsa_swit + QCA8K_PORT_PAD_RGMII_EN | + QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) | + QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY)); +- qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, +- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); ++ /* QCA8337 requires to set rgmii rx delay */ ++ if (priv->switch_id == QCA8K_ID_QCA8337) ++ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); + break; + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_1000BASEX: diff --git a/target/linux/generic/backport-5.10/735-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch b/target/linux/generic/backport-5.10/735-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch new file mode 100644 index 0000000000..2b393d242a --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch @@ -0,0 +1,48 @@ +From 0fc57e4b5e39461fc0a54aae0afe4241363a7267 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:03 +0200 +Subject: [PATCH] net: dsa: qca8k: add GLOBAL_FC settings needed for qca8327 + +Switch qca8327 needs special settings for the GLOBAL_FC_THRES regs. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 10 ++++++++++ + drivers/net/dsa/qca8k.h | 6 ++++++ + 2 files changed, 16 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -930,6 +930,16 @@ qca8k_setup(struct dsa_switch *ds) + } + } + ++ /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ ++ if (priv->switch_id == QCA8K_ID_QCA8327) { ++ mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) | ++ QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496); ++ qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH, ++ QCA8K_GLOBAL_FC_GOL_XON_THRES_S | ++ QCA8K_GLOBAL_FC_GOL_XOFF_THRES_S, ++ mask); ++ } ++ + /* Setup our port MTUs to match power on defaults */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) + priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -168,6 +168,12 @@ + #define QCA8K_PORT_LOOKUP_STATE GENMASK(18, 16) + #define QCA8K_PORT_LOOKUP_LEARN BIT(20) + ++#define QCA8K_REG_GLOBAL_FC_THRESH 0x800 ++#define QCA8K_GLOBAL_FC_GOL_XON_THRES(x) ((x) << 16) ++#define QCA8K_GLOBAL_FC_GOL_XON_THRES_S GENMASK(24, 16) ++#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES(x) ((x) << 0) ++#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES_S GENMASK(8, 0) ++ + #define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8) + #define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF GENMASK(3, 0) + #define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) ((x) << 0) diff --git a/target/linux/generic/backport-5.10/735-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch b/target/linux/generic/backport-5.10/735-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch new file mode 100644 index 0000000000..ed9b8188de --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch @@ -0,0 +1,114 @@ +From 95ffeaf18b3bb90eeef52cbf7d79ccc9d0345ff5 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:04 +0200 +Subject: [PATCH] net: dsa: qca8k: add support for switch rev + +qca8k internal phy driver require some special debug value to be set +based on the switch revision. Rework the switch id read function to +also read the chip revision. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 53 ++++++++++++++++++++++++++--------------- + drivers/net/dsa/qca8k.h | 7 ++++-- + 2 files changed, 39 insertions(+), 21 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1588,12 +1588,40 @@ static const struct dsa_switch_ops qca8k + .phylink_mac_link_up = qca8k_phylink_mac_link_up, + }; + ++static int qca8k_read_switch_id(struct qca8k_priv *priv) ++{ ++ const struct qca8k_match_data *data; ++ u32 val; ++ u8 id; ++ ++ /* get the switches ID from the compatible */ ++ data = of_device_get_match_data(priv->dev); ++ if (!data) ++ return -ENODEV; ++ ++ val = qca8k_read(priv, QCA8K_REG_MASK_CTRL); ++ if (val < 0) ++ return -ENODEV; ++ ++ id = QCA8K_MASK_CTRL_DEVICE_ID(val & QCA8K_MASK_CTRL_DEVICE_ID_MASK); ++ if (id != data->id) { ++ dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id); ++ return -ENODEV; ++ } ++ ++ priv->switch_id = id; ++ ++ /* Save revision to communicate to the internal PHY driver */ ++ priv->switch_revision = (val & QCA8K_MASK_CTRL_REV_ID_MASK); ++ ++ return 0; ++} ++ + static int + qca8k_sw_probe(struct mdio_device *mdiodev) + { +- const struct qca8k_match_data *data; + struct qca8k_priv *priv; +- u32 id; ++ int ret; + + /* allocate the private data struct so that we can probe the switches + * ID register +@@ -1619,24 +1647,11 @@ qca8k_sw_probe(struct mdio_device *mdiod + gpiod_set_value_cansleep(priv->reset_gpio, 0); + } + +- /* get the switches ID from the compatible */ +- data = of_device_get_match_data(&mdiodev->dev); +- if (!data) +- return -ENODEV; ++ /* Check the detected switch id */ ++ ret = qca8k_read_switch_id(priv); ++ if (ret) ++ return ret; + +- /* read the switches ID register */ +- id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); +- if (id < 0) +- return id; +- +- id >>= QCA8K_MASK_CTRL_ID_S; +- id &= QCA8K_MASK_CTRL_ID_M; +- if (id != data->id) { +- dev_err(&mdiodev->dev, "Switch id detected %x but expected %x", id, data->id); +- return -ENODEV; +- } +- +- priv->switch_id = id; + priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); + if (!priv->ds) + return -ENOMEM; +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -30,8 +30,10 @@ + + /* Global control registers */ + #define QCA8K_REG_MASK_CTRL 0x000 +-#define QCA8K_MASK_CTRL_ID_M 0xff +-#define QCA8K_MASK_CTRL_ID_S 8 ++#define QCA8K_MASK_CTRL_REV_ID_MASK GENMASK(7, 0) ++#define QCA8K_MASK_CTRL_REV_ID(x) ((x) >> 0) ++#define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8) ++#define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8) + #define QCA8K_REG_PORT0_PAD_CTRL 0x004 + #define QCA8K_REG_PORT5_PAD_CTRL 0x008 + #define QCA8K_REG_PORT6_PAD_CTRL 0x00c +@@ -251,6 +253,7 @@ struct qca8k_match_data { + + struct qca8k_priv { + u8 switch_id; ++ u8 switch_revision; + struct regmap *regmap; + struct mii_bus *bus; + struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/735-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch b/target/linux/generic/backport-5.10/735-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch new file mode 100644 index 0000000000..629cb324e0 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch @@ -0,0 +1,28 @@ +From 1ee0591a1093c2448642c33433483e9260275f7b Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:05 +0200 +Subject: [PATCH] net: dsa: qca8k: add ethernet-ports fallback to + setup_mdio_bus + +Dsa now also supports ethernet-ports. Add this new binding as a fallback +if the ports node can't be found. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -719,6 +719,9 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + + ports = of_get_child_by_name(priv->dev->of_node, "ports"); + if (!ports) ++ ports = of_get_child_by_name(priv->dev->of_node, "ethernet-ports"); ++ ++ if (!ports) + return -EINVAL; + + for_each_available_child_of_node(ports, port) { diff --git a/target/linux/generic/backport-5.10/735-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch b/target/linux/generic/backport-5.10/735-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch new file mode 100644 index 0000000000..6dc2dc6e3e --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch @@ -0,0 +1,188 @@ +From e4b9977cee1583da38a6e9118078bb728aaccf7b Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:06 +0200 +Subject: [PATCH] net: dsa: qca8k: make rgmii delay configurable + +The legacy qsdk code used a different delay instead of the max value. +Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable +using the standard rx/tx-internal-delay-ps ethernet binding and apply +qsdk values by default. The connected gmac doesn't add any delay so no +additional delay is added to tx/rx. +On this switch the delay is actually in ns so value should be in the +1000 order. Any value converted from ps to ns by dividing it by 1000 +as the switch max value for delay is 3ns. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 82 ++++++++++++++++++++++++++++++++++++++++- + drivers/net/dsa/qca8k.h | 11 +++--- + 2 files changed, 86 insertions(+), 7 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -778,6 +778,68 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + } + + static int ++qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv) ++{ ++ struct device_node *port_dn; ++ phy_interface_t mode; ++ struct dsa_port *dp; ++ u32 val; ++ ++ /* CPU port is already checked */ ++ dp = dsa_to_port(priv->ds, 0); ++ ++ port_dn = dp->dn; ++ ++ /* Check if port 0 is set to the correct type */ ++ of_get_phy_mode(port_dn, &mode); ++ if (mode != PHY_INTERFACE_MODE_RGMII_ID && ++ mode != PHY_INTERFACE_MODE_RGMII_RXID && ++ mode != PHY_INTERFACE_MODE_RGMII_TXID) { ++ return 0; ++ } ++ ++ switch (mode) { ++ case PHY_INTERFACE_MODE_RGMII_ID: ++ case PHY_INTERFACE_MODE_RGMII_RXID: ++ if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val)) ++ val = 2; ++ else ++ /* Switch regs accept value in ns, convert ps to ns */ ++ val = val / 1000; ++ ++ if (val > QCA8K_MAX_DELAY) { ++ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); ++ val = 3; ++ } ++ ++ priv->rgmii_rx_delay = val; ++ /* Stop here if we need to check only for rx delay */ ++ if (mode != PHY_INTERFACE_MODE_RGMII_ID) ++ break; ++ ++ fallthrough; ++ case PHY_INTERFACE_MODE_RGMII_TXID: ++ if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val)) ++ val = 1; ++ else ++ /* Switch regs accept value in ns, convert ps to ns */ ++ val = val / 1000; ++ ++ if (val > QCA8K_MAX_DELAY) { ++ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); ++ val = 3; ++ } ++ ++ priv->rgmii_tx_delay = val; ++ break; ++ default: ++ return 0; ++ } ++ ++ return 0; ++} ++ ++static int + qca8k_setup(struct dsa_switch *ds) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +@@ -802,6 +864,10 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + ++ ret = qca8k_setup_of_rgmii_delay(priv); ++ if (ret) ++ return ret; ++ + /* Enable CPU Port */ + ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, + QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); +@@ -970,6 +1036,8 @@ qca8k_phylink_mac_config(struct dsa_swit + case 0: /* 1st CPU port */ + if (state->interface != PHY_INTERFACE_MODE_RGMII && + state->interface != PHY_INTERFACE_MODE_RGMII_ID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && + state->interface != PHY_INTERFACE_MODE_SGMII) + return; + +@@ -985,6 +1053,8 @@ qca8k_phylink_mac_config(struct dsa_swit + case 6: /* 2nd CPU port / external PHY */ + if (state->interface != PHY_INTERFACE_MODE_RGMII && + state->interface != PHY_INTERFACE_MODE_RGMII_ID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && + state->interface != PHY_INTERFACE_MODE_SGMII && + state->interface != PHY_INTERFACE_MODE_1000BASEX) + return; +@@ -1008,14 +1078,18 @@ qca8k_phylink_mac_config(struct dsa_swit + qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); + break; + case PHY_INTERFACE_MODE_RGMII_ID: ++ case PHY_INTERFACE_MODE_RGMII_TXID: ++ case PHY_INTERFACE_MODE_RGMII_RXID: + /* RGMII_ID needs internal delay. This is enabled through + * PORT5_PAD_CTRL for all ports, rather than individual port + * registers + */ + qca8k_write(priv, reg, + QCA8K_PORT_PAD_RGMII_EN | +- QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) | +- QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY)); ++ QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) | ++ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); + /* QCA8337 requires to set rgmii rx delay */ + if (priv->switch_id == QCA8K_ID_QCA8337) + qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, +@@ -1073,6 +1147,8 @@ qca8k_phylink_validate(struct dsa_switch + if (state->interface != PHY_INTERFACE_MODE_NA && + state->interface != PHY_INTERFACE_MODE_RGMII && + state->interface != PHY_INTERFACE_MODE_RGMII_ID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && + state->interface != PHY_INTERFACE_MODE_SGMII) + goto unsupported; + break; +@@ -1090,6 +1166,8 @@ qca8k_phylink_validate(struct dsa_switch + if (state->interface != PHY_INTERFACE_MODE_NA && + state->interface != PHY_INTERFACE_MODE_RGMII && + state->interface != PHY_INTERFACE_MODE_RGMII_ID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && ++ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && + state->interface != PHY_INTERFACE_MODE_SGMII && + state->interface != PHY_INTERFACE_MODE_1000BASEX) + goto unsupported; +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -38,12 +38,11 @@ + #define QCA8K_REG_PORT5_PAD_CTRL 0x008 + #define QCA8K_REG_PORT6_PAD_CTRL 0x00c + #define QCA8K_PORT_PAD_RGMII_EN BIT(26) +-#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) \ +- ((0x8 + (x & 0x3)) << 22) +-#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) \ +- ((0x10 + (x & 0x3)) << 20) +-#define QCA8K_MAX_DELAY 3 ++#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) ((x) << 22) ++#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) ((x) << 20) ++#define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25) + #define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24) ++#define QCA8K_MAX_DELAY 3 + #define QCA8K_PORT_PAD_SGMII_EN BIT(7) + #define QCA8K_REG_PWS 0x010 + #define QCA8K_PWS_SERDES_AEN_DIS BIT(7) +@@ -254,6 +253,8 @@ struct qca8k_match_data { + struct qca8k_priv { + u8 switch_id; + u8 switch_revision; ++ u8 rgmii_tx_delay; ++ u8 rgmii_rx_delay; + struct regmap *regmap; + struct mii_bus *bus; + struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/735-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch b/target/linux/generic/backport-5.10/735-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch new file mode 100644 index 0000000000..4593da032b --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch @@ -0,0 +1,50 @@ +From 63c33bbfeb6842a956a0eb12901e28eb335bdb18 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:07 +0200 +Subject: [PATCH] net: dsa: qca8k: clear MASTER_EN after phy read/write + +Clear MDIO_MASTER_EN bit from MDIO_MASTER_CTRL after read/write +operation. The MDIO_MASTER_EN bit is not reset after read/write +operation and the next operation can be wrongly interpreted by the +switch as a mdio operation. This cause a production of wrong/garbage +data from the switch and underfined bheavior. (random port drop, +unplugged port flagged with link up, wrong port speed) +Also on driver remove the MASTER_CTRL can be left set and cause the +malfunction of any next driver using the mdio device. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 14 ++++++++++++-- + 1 file changed, 12 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -649,8 +649,14 @@ qca8k_mdio_write(struct qca8k_priv *priv + if (ret) + return ret; + +- return qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_BUSY); ++ ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_BUSY); ++ ++ /* even if the busy_wait timeouts try to clear the MASTER_EN */ ++ qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_EN); ++ ++ return ret; + } + + static int +@@ -685,6 +691,10 @@ qca8k_mdio_read(struct qca8k_priv *priv, + + val &= QCA8K_MDIO_MASTER_DATA_MASK; + ++ /* even if the busy_wait timeouts try to clear the MASTER_EN */ ++ qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_EN); ++ + return val; + } + diff --git a/target/linux/generic/backport-5.10/735-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch b/target/linux/generic/backport-5.10/735-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch new file mode 100644 index 0000000000..b6684d7210 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch @@ -0,0 +1,128 @@ +From 60df02b6ea4581d72eb7a3ab7204504a54059b72 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:08 +0200 +Subject: [PATCH] net: dsa: qca8k: dsa: qca8k: protect MASTER busy_wait with + mdio mutex + +MDIO_MASTER operation have a dedicated busy wait that is not protected +by the mdio mutex. This can cause situation where the MASTER operation +is done and a normal operation is executed between the MASTER read/write +and the MASTER busy_wait. Rework the qca8k_mdio_read/write function to +address this issue by binding the lock for the whole MASTER operation +and not only the mdio read/write common operation. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 68 +++++++++++++++++++++++++++++++++-------- + 1 file changed, 55 insertions(+), 13 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -628,8 +628,31 @@ qca8k_port_to_phy(int port) + } + + static int ++qca8k_mdio_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) ++{ ++ u16 r1, r2, page; ++ u32 val; ++ int ret; ++ ++ qca8k_split_addr(reg, &r1, &r2, &page); ++ ++ ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, ++ QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, ++ priv->bus, 0x10 | r2, r1); ++ ++ /* Check if qca8k_read has failed for a different reason ++ * before returnting -ETIMEDOUT ++ */ ++ if (ret < 0 && val < 0) ++ return val; ++ ++ return ret; ++} ++ ++static int + qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) + { ++ u16 r1, r2, page; + u32 phy, val; + int ret; + +@@ -645,12 +668,21 @@ qca8k_mdio_write(struct qca8k_priv *priv + QCA8K_MDIO_MASTER_REG_ADDR(regnum) | + QCA8K_MDIO_MASTER_DATA(data); + +- ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); ++ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); ++ ++ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ ++ ret = qca8k_set_page(priv->bus, page); + if (ret) +- return ret; ++ goto exit; ++ ++ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); + +- ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_BUSY); ++ ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_BUSY); ++ ++exit: ++ mutex_unlock(&priv->bus->mdio_lock); + + /* even if the busy_wait timeouts try to clear the MASTER_EN */ + qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, +@@ -662,6 +694,7 @@ qca8k_mdio_write(struct qca8k_priv *priv + static int + qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) + { ++ u16 r1, r2, page; + u32 phy, val; + int ret; + +@@ -676,21 +709,30 @@ qca8k_mdio_read(struct qca8k_priv *priv, + QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | + QCA8K_MDIO_MASTER_REG_ADDR(regnum); + +- ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); +- if (ret) +- return ret; ++ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); ++ ++ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); + +- ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_BUSY); ++ ret = qca8k_set_page(priv->bus, page); + if (ret) +- return ret; ++ goto exit; + +- val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); +- if (val < 0) +- return val; ++ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); ++ ++ ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ QCA8K_MDIO_MASTER_BUSY); ++ if (ret) ++ goto exit; + ++ val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); + val &= QCA8K_MDIO_MASTER_DATA_MASK; + ++exit: ++ mutex_unlock(&priv->bus->mdio_lock); ++ ++ if (val >= 0) ++ val &= QCA8K_MDIO_MASTER_DATA_MASK; ++ + /* even if the busy_wait timeouts try to clear the MASTER_EN */ + qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_EN); diff --git a/target/linux/generic/backport-5.10/735-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch b/target/linux/generic/backport-5.10/735-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch new file mode 100644 index 0000000000..30eeed361e --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch @@ -0,0 +1,39 @@ +From 617960d72e93de0f3fa52407e2d39e8c43e73b0a Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:09 +0200 +Subject: [PATCH] net: dsa: qca8k: enlarge mdio delay and timeout + +The witch require some extra delay after setting page or the next +read/write can use still use the old page. Add a delay after the +set_page function to address this as it's done in QSDK legacy driver. +Some timeouts were notice with VLAN and phy function, enlarge the +mdio busy wait timeout to fix these problems. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 1 + + drivers/net/dsa/qca8k.h | 2 +- + 2 files changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -143,6 +143,7 @@ qca8k_set_page(struct mii_bus *bus, u16 + } + + qca8k_current_page = page; ++ usleep_range(1000, 2000); + return 0; + } + +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -20,7 +20,7 @@ + #define PHY_ID_QCA8337 0x004dd036 + #define QCA8K_ID_QCA8337 0x13 + +-#define QCA8K_BUSY_WAIT_TIMEOUT 20 ++#define QCA8K_BUSY_WAIT_TIMEOUT 2000 + + #define QCA8K_NUM_FDB_RECORDS 2048 + diff --git a/target/linux/generic/backport-5.10/735-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch b/target/linux/generic/backport-5.10/735-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch new file mode 100644 index 0000000000..88d3c1ef43 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch @@ -0,0 +1,267 @@ +From 759bafb8a3226326ca357613bc90acf738f80c32 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:10 +0200 +Subject: [PATCH] net: dsa: qca8k: add support for internal phy and internal + mdio + +Add support to setup_mdio_bus for internal phy declaration. Introduce a +flag to use the legacy port phy mapping by default and use the direct +mapping if a mdio node is detected in the switch node. Register a +dedicated mdio internal mdio bus to address the different mapping +between port and phy if the mdio node is detected. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 112 +++++++++++++++++++++++++++++----------- + drivers/net/dsa/qca8k.h | 1 + + 2 files changed, 83 insertions(+), 30 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -11,6 +11,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -629,7 +630,7 @@ qca8k_port_to_phy(int port) + } + + static int +-qca8k_mdio_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) ++qca8k_mdio_busy_wait(struct mii_bus *bus, u32 reg, u32 mask) + { + u16 r1, r2, page; + u32 val; +@@ -639,7 +640,7 @@ qca8k_mdio_busy_wait(struct qca8k_priv * + + ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, + QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, +- priv->bus, 0x10 | r2, r1); ++ bus, 0x10 | r2, r1); + + /* Check if qca8k_read has failed for a different reason + * before returnting -ETIMEDOUT +@@ -651,19 +652,16 @@ qca8k_mdio_busy_wait(struct qca8k_priv * + } + + static int +-qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) ++qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) + { ++ struct qca8k_priv *priv = salve_bus->priv; + u16 r1, r2, page; +- u32 phy, val; ++ u32 val; + int ret; + + if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) + return -EINVAL; + +- /* callee is responsible for not passing bad ports, +- * but we still would like to make spills impossible. +- */ +- phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; + val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | + QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | + QCA8K_MDIO_MASTER_REG_ADDR(regnum) | +@@ -679,33 +677,29 @@ qca8k_mdio_write(struct qca8k_priv *priv + + qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); + +- ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY); + + exit: +- mutex_unlock(&priv->bus->mdio_lock); +- + /* even if the busy_wait timeouts try to clear the MASTER_EN */ +- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_EN); ++ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); ++ ++ mutex_unlock(&priv->bus->mdio_lock); + + return ret; + } + + static int +-qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) ++qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) + { ++ struct qca8k_priv *priv = salve_bus->priv; + u16 r1, r2, page; +- u32 phy, val; ++ u32 val; + int ret; + + if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) + return -EINVAL; + +- /* callee is responsible for not passing bad ports, +- * but we still would like to make spills impossible. +- */ +- phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; + val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | + QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | + QCA8K_MDIO_MASTER_REG_ADDR(regnum); +@@ -720,24 +714,22 @@ qca8k_mdio_read(struct qca8k_priv *priv, + + qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); + +- ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, ++ ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY); + if (ret) + goto exit; + + val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); +- val &= QCA8K_MDIO_MASTER_DATA_MASK; + + exit: ++ /* even if the busy_wait timeouts try to clear the MASTER_EN */ ++ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); ++ + mutex_unlock(&priv->bus->mdio_lock); + + if (val >= 0) + val &= QCA8K_MDIO_MASTER_DATA_MASK; + +- /* even if the busy_wait timeouts try to clear the MASTER_EN */ +- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, +- QCA8K_MDIO_MASTER_EN); +- + return val; + } + +@@ -746,7 +738,14 @@ qca8k_phy_write(struct dsa_switch *ds, i + { + struct qca8k_priv *priv = ds->priv; + +- return qca8k_mdio_write(priv, port, regnum, data); ++ /* Check if the legacy mapping should be used and the ++ * port is not correctly mapped to the right PHY in the ++ * devicetree ++ */ ++ if (priv->legacy_phy_port_mapping) ++ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; ++ ++ return qca8k_mdio_write(priv->bus, port, regnum, data); + } + + static int +@@ -755,7 +754,14 @@ qca8k_phy_read(struct dsa_switch *ds, in + struct qca8k_priv *priv = ds->priv; + int ret; + +- ret = qca8k_mdio_read(priv, port, regnum); ++ /* Check if the legacy mapping should be used and the ++ * port is not correctly mapped to the right PHY in the ++ * devicetree ++ */ ++ if (priv->legacy_phy_port_mapping) ++ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; ++ ++ ret = qca8k_mdio_read(priv->bus, port, regnum); + + if (ret < 0) + return 0xffff; +@@ -764,10 +770,37 @@ qca8k_phy_read(struct dsa_switch *ds, in + } + + static int ++qca8k_mdio_register(struct qca8k_priv *priv, struct device_node *mdio) ++{ ++ struct dsa_switch *ds = priv->ds; ++ struct mii_bus *bus; ++ ++ bus = devm_mdiobus_alloc(ds->dev); ++ ++ if (!bus) ++ return -ENOMEM; ++ ++ bus->priv = (void *)priv; ++ bus->name = "qca8k slave mii"; ++ bus->read = qca8k_mdio_read; ++ bus->write = qca8k_mdio_write; ++ snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d", ++ ds->index); ++ ++ bus->parent = ds->dev; ++ bus->phy_mask = ~ds->phys_mii_mask; ++ ++ ds->slave_mii_bus = bus; ++ ++ return devm_of_mdiobus_register(priv->dev, bus, mdio); ++} ++ ++static int + qca8k_setup_mdio_bus(struct qca8k_priv *priv) + { + u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg; +- struct device_node *ports, *port; ++ struct device_node *ports, *port, *mdio; ++ phy_interface_t mode; + int err; + + ports = of_get_child_by_name(priv->dev->of_node, "ports"); +@@ -788,7 +821,10 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + if (!dsa_is_user_port(priv->ds, reg)) + continue; + +- if (of_property_read_bool(port, "phy-handle")) ++ of_get_phy_mode(port, &mode); ++ ++ if (of_property_read_bool(port, "phy-handle") && ++ mode != PHY_INTERFACE_MODE_INTERNAL) + external_mdio_mask |= BIT(reg); + else + internal_mdio_mask |= BIT(reg); +@@ -825,8 +861,23 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + QCA8K_MDIO_MASTER_EN); + } + ++ /* Check if the devicetree declare the port:phy mapping */ ++ mdio = of_get_child_by_name(priv->dev->of_node, "mdio"); ++ if (of_device_is_available(mdio)) { ++ err = qca8k_mdio_register(priv, mdio); ++ if (err) ++ of_node_put(mdio); ++ ++ return err; ++ } ++ ++ /* If a mapping can't be found the legacy mapping is used, ++ * using the qca8k_port_to_phy function ++ */ ++ priv->legacy_phy_port_mapping = true; + priv->ops.phy_read = qca8k_phy_read; + priv->ops.phy_write = qca8k_phy_write; ++ + return 0; + } + +@@ -1212,7 +1263,8 @@ qca8k_phylink_validate(struct dsa_switch + case 5: + /* Internal PHY */ + if (state->interface != PHY_INTERFACE_MODE_NA && +- state->interface != PHY_INTERFACE_MODE_GMII) ++ state->interface != PHY_INTERFACE_MODE_GMII && ++ state->interface != PHY_INTERFACE_MODE_INTERNAL) + goto unsupported; + break; + case 6: /* 2nd CPU port / external PHY */ +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -255,6 +255,7 @@ struct qca8k_priv { + u8 switch_revision; + u8 rgmii_tx_delay; + u8 rgmii_rx_delay; ++ bool legacy_phy_port_mapping; + struct regmap *regmap; + struct mii_bus *bus; + struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/735-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch b/target/linux/generic/backport-5.10/735-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch new file mode 100644 index 0000000000..6db01b4b41 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch @@ -0,0 +1,93 @@ +From 0c994a28e7518f098c84a3049cb2915780db873a Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:11 +0200 +Subject: [PATCH] devicetree: bindings: dsa: qca8k: Document internal mdio + definition + +Document new way of declare mapping of internal PHY to port. +The new implementation directly declare the PHY connected to the port +by adding a node in the switch node. The driver detect this and register +an internal mdiobus using the mapping defined in the mdio node. + +Signed-off-by: Ansuel Smith +Reviewed-by: Rob Herring +Signed-off-by: David S. Miller +--- + .../devicetree/bindings/net/dsa/qca8k.txt | 39 +++++++++++++++++++ + 1 file changed, 39 insertions(+) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -21,6 +21,10 @@ described in dsa/dsa.txt. If the QCA8K s + mdio-bus each subnode describing a port needs to have a valid phandle + referencing the internal PHY it is connected to. This is because there's no + N:N mapping of port and PHY id. ++To declare the internal mdio-bus configuration, declare a mdio node in the ++switch node and declare the phandle for the port referencing the internal ++PHY is connected to. In this config a internal mdio-bus is registered and ++the mdio MASTER is used as communication. + + Don't use mixed external and internal mdio-bus configurations, as this is + not supported by the hardware. +@@ -150,26 +154,61 @@ for the internal master mdio-bus configu + port@1 { + reg = <1>; + label = "lan1"; ++ phy-mode = "internal"; ++ phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; ++ phy-mode = "internal"; ++ phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; ++ phy-mode = "internal"; ++ phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; ++ phy-mode = "internal"; ++ phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; ++ phy-mode = "internal"; ++ phy-handle = <&phy_port5>; ++ }; ++ }; ++ ++ mdio { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ phy_port1: phy@0 { ++ reg = <0>; ++ }; ++ ++ phy_port2: phy@1 { ++ reg = <1>; ++ }; ++ ++ phy_port3: phy@2 { ++ reg = <2>; ++ }; ++ ++ phy_port4: phy@3 { ++ reg = <3>; ++ }; ++ ++ phy_port5: phy@4 { ++ reg = <4>; + }; + }; + }; diff --git a/target/linux/generic/backport-5.10/735-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch b/target/linux/generic/backport-5.10/735-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch new file mode 100644 index 0000000000..da8d5b3462 --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch @@ -0,0 +1,95 @@ +From b7ebac354d54f1657bb89b7a7ca149db50203e6a Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:12 +0200 +Subject: [PATCH] net: dsa: qca8k: improve internal mdio read/write bus access + +Improve the internal mdio read/write bus access by caching the value +without accessing it for every read/write. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 28 +++++++++++++++------------- + 1 file changed, 15 insertions(+), 13 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -655,6 +655,7 @@ static int + qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) + { + struct qca8k_priv *priv = salve_bus->priv; ++ struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 val; + int ret; +@@ -669,22 +670,22 @@ qca8k_mdio_write(struct mii_bus *salve_b + + qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- ret = qca8k_set_page(priv->bus, page); ++ ret = qca8k_set_page(bus, page); + if (ret) + goto exit; + +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, val); + +- ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, ++ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY); + + exit: + /* even if the busy_wait timeouts try to clear the MASTER_EN */ +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, 0); + +- mutex_unlock(&priv->bus->mdio_lock); ++ mutex_unlock(&bus->mdio_lock); + + return ret; + } +@@ -693,6 +694,7 @@ static int + qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) + { + struct qca8k_priv *priv = salve_bus->priv; ++ struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 val; + int ret; +@@ -706,26 +708,26 @@ qca8k_mdio_read(struct mii_bus *salve_bu + + qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- ret = qca8k_set_page(priv->bus, page); ++ ret = qca8k_set_page(bus, page); + if (ret) + goto exit; + +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, val); + +- ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, ++ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, + QCA8K_MDIO_MASTER_BUSY); + if (ret) + goto exit; + +- val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); ++ val = qca8k_mii_read32(bus, 0x10 | r2, r1); + + exit: + /* even if the busy_wait timeouts try to clear the MASTER_EN */ +- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); ++ qca8k_mii_write32(bus, 0x10 | r2, r1, 0); + +- mutex_unlock(&priv->bus->mdio_lock); ++ mutex_unlock(&bus->mdio_lock); + + if (val >= 0) + val &= QCA8K_MDIO_MASTER_DATA_MASK; diff --git a/target/linux/generic/backport-5.10/735-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch b/target/linux/generic/backport-5.10/735-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch new file mode 100644 index 0000000000..1179cf152d --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch @@ -0,0 +1,48 @@ +From a46aec02bc06ac2c33f326339e4ef88c735dc30d Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:13 +0200 +Subject: [PATCH] net: dsa: qca8k: pass switch_revision info to phy dev_flags + +Define get_phy_flags to pass switch_Revision needed to tweak the +internal PHY with debug values based on the revision. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 17 +++++++++++++++++ + 1 file changed, 17 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1740,6 +1740,22 @@ qca8k_port_vlan_del(struct dsa_switch *d + return ret; + } + ++static u32 qca8k_get_phy_flags(struct dsa_switch *ds, int port) ++{ ++ struct qca8k_priv *priv = ds->priv; ++ ++ /* Communicate to the phy internal driver the switch revision. ++ * Based on the switch revision different values needs to be ++ * set to the dbg and mmd reg on the phy. ++ * The first 2 bit are used to communicate the switch revision ++ * to the phy driver. ++ */ ++ if (port > 0 && port < 6) ++ return priv->switch_revision; ++ ++ return 0; ++} ++ + static enum dsa_tag_protocol + qca8k_get_tag_protocol(struct dsa_switch *ds, int port, + enum dsa_tag_protocol mp) +@@ -1774,6 +1790,7 @@ static const struct dsa_switch_ops qca8k + .phylink_mac_config = qca8k_phylink_mac_config, + .phylink_mac_link_down = qca8k_phylink_mac_link_down, + .phylink_mac_link_up = qca8k_phylink_mac_link_up, ++ .get_phy_flags = qca8k_get_phy_flags, + }; + + static int qca8k_read_switch_id(struct qca8k_priv *priv) diff --git a/target/linux/generic/backport-5.10/735-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch b/target/linux/generic/backport-5.10/735-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch new file mode 100644 index 0000000000..20325f564d --- /dev/null +++ b/target/linux/generic/backport-5.10/735-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch @@ -0,0 +1,229 @@ +From 272833b9b3b3969be7a91839121d86662c8c4253 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Fri, 14 May 2021 23:00:15 +0200 +Subject: [PATCH] net: phy: add support for qca8k switch internal PHY in at803x + +Since the at803x share the same regs, it's assumed they are based on the +same implementation. Make it part of the at803x PHY driver to skip +having redudant code. +Add initial support for qca8k internal PHYs. The internal PHYs requires +special mmd and debug values to be set based on the switch revision +passwd using the dev_flags. Supports output of idle, receive and eee_wake +errors stats. +Some debug values sets can't be translated as the documentation lacks any +reference about them. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/phy/Kconfig | 5 +- + drivers/net/phy/at803x.c | 132 ++++++++++++++++++++++++++++++++++++++- + 2 files changed, 134 insertions(+), 3 deletions(-) + +--- a/drivers/net/phy/Kconfig ++++ b/drivers/net/phy/Kconfig +@@ -235,10 +235,11 @@ config NXP_TJA11XX_PHY + Currently supports the NXP TJA1100 and TJA1101 PHY. + + config AT803X_PHY +- tristate "Qualcomm Atheros AR803X PHYs" ++ tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" + depends on REGULATOR + help +- Currently supports the AR8030, AR8031, AR8033 and AR8035 model ++ Currently supports the AR8030, AR8031, AR8033, AR8035 and internal ++ QCA8337(Internal qca8k PHY) model + + config QSEMI_PHY + tristate "Quality Semiconductor PHYs" +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -92,10 +92,16 @@ + #define AT803X_DEBUG_REG_5 0x05 + #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) + ++#define AT803X_DEBUG_REG_3C 0x3C ++ ++#define AT803X_DEBUG_REG_3D 0x3D ++ + #define AT803X_DEBUG_REG_1F 0x1F + #define AT803X_DEBUG_PLL_ON BIT(2) + #define AT803X_DEBUG_RGMII_1V8 BIT(3) + ++#define MDIO_AZ_DEBUG 0x800D ++ + /* AT803x supports either the XTAL input pad, an internal PLL or the + * DSP as clock reference for the clock output pad. The XTAL reference + * is only used for 25 MHz output, all other frequencies need the PLL. +@@ -142,10 +148,34 @@ + #define AT803X_PAGE_FIBER 0 + #define AT803X_PAGE_COPPER 1 + ++#define QCA8327_PHY_ID 0x004dd034 ++#define QCA8337_PHY_ID 0x004dd036 ++#define QCA8K_PHY_ID_MASK 0xffffffff ++ ++#define QCA8K_DEVFLAGS_REVISION_MASK GENMASK(2, 0) ++ + MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); + MODULE_AUTHOR("Matus Ujhelyi"); + MODULE_LICENSE("GPL"); + ++enum stat_access_type { ++ PHY, ++ MMD ++}; ++ ++struct at803x_hw_stat { ++ const char *string; ++ u8 reg; ++ u32 mask; ++ enum stat_access_type access_type; ++}; ++ ++static struct at803x_hw_stat at803x_hw_stats[] = { ++ { "phy_idle_errors", 0xa, GENMASK(7, 0), PHY}, ++ { "phy_receive_errors", 0x15, GENMASK(15, 0), PHY}, ++ { "eee_wake_errors", 0x16, GENMASK(15, 0), MMD}, ++}; ++ + struct at803x_priv { + int flags; + #define AT803X_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */ +@@ -154,6 +184,7 @@ struct at803x_priv { + struct regulator_dev *vddio_rdev; + struct regulator_dev *vddh_rdev; + struct regulator *vddio; ++ u64 stats[ARRAY_SIZE(at803x_hw_stats)]; + }; + + struct at803x_context { +@@ -165,6 +196,17 @@ struct at803x_context { + u16 led_control; + }; + ++static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data) ++{ ++ int ret; ++ ++ ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg); ++ if (ret < 0) ++ return ret; ++ ++ return phy_write(phydev, AT803X_DEBUG_DATA, data); ++} ++ + static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg) + { + int ret; +@@ -327,6 +369,53 @@ static void at803x_get_wol(struct phy_de + wol->wolopts |= WAKE_MAGIC; + } + ++static int at803x_get_sset_count(struct phy_device *phydev) ++{ ++ return ARRAY_SIZE(at803x_hw_stats); ++} ++ ++static void at803x_get_strings(struct phy_device *phydev, u8 *data) ++{ ++ int i; ++ ++ for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) { ++ strscpy(data + i * ETH_GSTRING_LEN, ++ at803x_hw_stats[i].string, ETH_GSTRING_LEN); ++ } ++} ++ ++static u64 at803x_get_stat(struct phy_device *phydev, int i) ++{ ++ struct at803x_hw_stat stat = at803x_hw_stats[i]; ++ struct at803x_priv *priv = phydev->priv; ++ int val; ++ u64 ret; ++ ++ if (stat.access_type == MMD) ++ val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg); ++ else ++ val = phy_read(phydev, stat.reg); ++ ++ if (val < 0) { ++ ret = U64_MAX; ++ } else { ++ val = val & stat.mask; ++ priv->stats[i] += val; ++ ret = priv->stats[i]; ++ } ++ ++ return ret; ++} ++ ++static void at803x_get_stats(struct phy_device *phydev, ++ struct ethtool_stats *stats, u64 *data) ++{ ++ int i; ++ ++ for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) ++ data[i] = at803x_get_stat(phydev, i); ++} ++ + static int at803x_suspend(struct phy_device *phydev) + { + int value; +@@ -1102,6 +1191,34 @@ static int at803x_cable_test_start(struc + return 0; + } + ++static int qca83xx_config_init(struct phy_device *phydev) ++{ ++ u8 switch_revision; ++ ++ switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK; ++ ++ switch (switch_revision) { ++ case 1: ++ /* For 100M waveform */ ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_0, 0x02ea); ++ /* Turn on Gigabit clock */ ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x68a0); ++ break; ++ ++ case 2: ++ phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0); ++ fallthrough; ++ case 4: ++ phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x6860); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_5, 0x2c46); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000); ++ break; ++ } ++ ++ return 0; ++} ++ + static struct phy_driver at803x_driver[] = { + { + /* Qualcomm Atheros AR8035 */ +@@ -1198,7 +1315,20 @@ static struct phy_driver at803x_driver[] + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, +-} }; ++}, { ++ /* QCA8337 */ ++ .phy_id = QCA8337_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "QCA PHY 8337", ++ /* PHY_GBIT_FEATURES */ ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, ++}, }; + + module_phy_driver(at803x_driver); + diff --git a/target/linux/generic/backport-5.10/736-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch b/target/linux/generic/backport-5.10/736-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch new file mode 100644 index 0000000000..a68e3b1821 --- /dev/null +++ b/target/linux/generic/backport-5.10/736-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch @@ -0,0 +1,64 @@ +From 0d56e5c191b197e1d30a0a4c92628836dafced0f Mon Sep 17 00:00:00 2001 +From: Wei Yongjun +Date: Tue, 18 May 2021 11:24:13 +0000 +Subject: [PATCH] net: dsa: qca8k: fix missing unlock on error in + qca8k_vlan_(add|del) + +Add the missing unlock before return from function qca8k_vlan_add() +and qca8k_vlan_del() in the error handling case. + +Fixes: 028f5f8ef44f ("net: dsa: qca8k: handle error with qca8k_read operation") +Reported-by: Hulk Robot +Signed-off-by: Wei Yongjun +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 16 ++++++++++------ + 1 file changed, 10 insertions(+), 6 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -506,8 +506,10 @@ qca8k_vlan_add(struct qca8k_priv *priv, + goto out; + + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); +- if (reg < 0) +- return reg; ++ if (reg < 0) { ++ ret = reg; ++ goto out; ++ } + reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; + reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + if (untagged) +@@ -519,7 +521,7 @@ qca8k_vlan_add(struct qca8k_priv *priv, + + ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); + if (ret) +- return ret; ++ goto out; + ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); + + out: +@@ -541,8 +543,10 @@ qca8k_vlan_del(struct qca8k_priv *priv, + goto out; + + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); +- if (reg < 0) +- return reg; ++ if (reg < 0) { ++ ret = reg; ++ goto out; ++ } + reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << + QCA8K_VTU_FUNC0_EG_MODE_S(port); +@@ -564,7 +568,7 @@ qca8k_vlan_del(struct qca8k_priv *priv, + } else { + ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); + if (ret) +- return ret; ++ goto out; + ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); + } + diff --git a/target/linux/generic/backport-5.10/737-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch b/target/linux/generic/backport-5.10/737-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch new file mode 100644 index 0000000000..451b0e9446 --- /dev/null +++ b/target/linux/generic/backport-5.10/737-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch @@ -0,0 +1,348 @@ +From 7c9896e37807862e276064dd9331860f5d27affc Mon Sep 17 00:00:00 2001 +From: Yang Yingliang +Date: Sat, 29 May 2021 11:04:38 +0800 +Subject: [PATCH] net: dsa: qca8k: check return value of read functions + correctly + +Current return type of qca8k_mii_read32() and qca8k_read() are +unsigned, it can't be negative, so the return value check is +unuseful. For check the return value correctly, change return +type of the read functions and add a output parameter to store +the read value. + +Signed-off-by: Yang Yingliang +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/qca8k.c | 130 +++++++++++++++++++--------------------- + 1 file changed, 60 insertions(+), 70 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -89,26 +89,26 @@ qca8k_split_addr(u32 regaddr, u16 *r1, u + *page = regaddr & 0x3ff; + } + +-static u32 +-qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum) ++static int ++qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum, u32 *val) + { +- u32 val; + int ret; + + ret = bus->read(bus, phy_id, regnum); + if (ret >= 0) { +- val = ret; ++ *val = ret; + ret = bus->read(bus, phy_id, regnum + 1); +- val |= ret << 16; ++ *val |= ret << 16; + } + + if (ret < 0) { + dev_err_ratelimited(&bus->dev, + "failed to read qca8k 32bit register\n"); ++ *val = 0; + return ret; + } + +- return val; ++ return 0; + } + + static void +@@ -148,26 +148,26 @@ qca8k_set_page(struct mii_bus *bus, u16 + return 0; + } + +-static u32 +-qca8k_read(struct qca8k_priv *priv, u32 reg) ++static int ++qca8k_read(struct qca8k_priv *priv, u32 reg, u32 *val) + { + struct mii_bus *bus = priv->bus; + u16 r1, r2, page; +- u32 val; ++ int ret; + + qca8k_split_addr(reg, &r1, &r2, &page); + + mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- val = qca8k_set_page(bus, page); +- if (val < 0) ++ ret = qca8k_set_page(bus, page); ++ if (ret < 0) + goto exit; + +- val = qca8k_mii_read32(bus, 0x10 | r2, r1); ++ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, val); + + exit: + mutex_unlock(&bus->mdio_lock); +- return val; ++ return ret; + } + + static int +@@ -208,11 +208,9 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r + if (ret < 0) + goto exit; + +- val = qca8k_mii_read32(bus, 0x10 | r2, r1); +- if (val < 0) { +- ret = val; ++ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); ++ if (ret < 0) + goto exit; +- } + + val &= ~mask; + val |= write_val; +@@ -240,15 +238,8 @@ static int + qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ctx; +- int ret; +- +- ret = qca8k_read(priv, reg); +- if (ret < 0) +- return ret; +- +- *val = ret; + +- return 0; ++ return qca8k_read(priv, reg, val); + } + + static int +@@ -296,18 +287,18 @@ static struct regmap_config qca8k_regmap + static int + qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) + { ++ int ret, ret1; + u32 val; +- int ret; + +- ret = read_poll_timeout(qca8k_read, val, !(val & mask), ++ ret = read_poll_timeout(qca8k_read, ret1, !(val & mask), + 0, QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, +- priv, reg); ++ priv, reg, &val); + + /* Check if qca8k_read has failed for a different reason + * before returning -ETIMEDOUT + */ +- if (ret < 0 && val < 0) +- return val; ++ if (ret < 0 && ret1 < 0) ++ return ret1; + + return ret; + } +@@ -316,13 +307,13 @@ static int + qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) + { + u32 reg[4], val; +- int i; ++ int i, ret; + + /* load the ARL table into an array */ + for (i = 0; i < 4; i++) { +- val = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); +- if (val < 0) +- return val; ++ ret = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4), &val); ++ if (ret < 0) ++ return ret; + + reg[i] = val; + } +@@ -396,9 +387,9 @@ qca8k_fdb_access(struct qca8k_priv *priv + + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_FDB_LOAD) { +- reg = qca8k_read(priv, QCA8K_REG_ATU_FUNC); +- if (reg < 0) +- return reg; ++ ret = qca8k_read(priv, QCA8K_REG_ATU_FUNC, ®); ++ if (ret < 0) ++ return ret; + if (reg & QCA8K_ATU_FUNC_FULL) + return -1; + } +@@ -477,9 +468,9 @@ qca8k_vlan_access(struct qca8k_priv *pri + + /* Check for table full violation when adding an entry */ + if (cmd == QCA8K_VLAN_LOAD) { +- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1); +- if (reg < 0) +- return reg; ++ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC1, ®); ++ if (ret < 0) ++ return ret; + if (reg & QCA8K_VTU_FUNC1_FULL) + return -ENOMEM; + } +@@ -505,11 +496,9 @@ qca8k_vlan_add(struct qca8k_priv *priv, + if (ret < 0) + goto out; + +- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); +- if (reg < 0) { +- ret = reg; ++ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); ++ if (ret < 0) + goto out; +- } + reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; + reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + if (untagged) +@@ -542,11 +531,9 @@ qca8k_vlan_del(struct qca8k_priv *priv, + if (ret < 0) + goto out; + +- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); +- if (reg < 0) { +- ret = reg; ++ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); ++ if (ret < 0) + goto out; +- } + reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); + reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << + QCA8K_VTU_FUNC0_EG_MODE_S(port); +@@ -638,19 +625,19 @@ qca8k_mdio_busy_wait(struct mii_bus *bus + { + u16 r1, r2, page; + u32 val; +- int ret; ++ int ret, ret1; + + qca8k_split_addr(reg, &r1, &r2, &page); + +- ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, ++ ret = read_poll_timeout(qca8k_mii_read32, ret1, !(val & mask), 0, + QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, +- bus, 0x10 | r2, r1); ++ bus, 0x10 | r2, r1, &val); + + /* Check if qca8k_read has failed for a different reason + * before returnting -ETIMEDOUT + */ +- if (ret < 0 && val < 0) +- return val; ++ if (ret < 0 && ret1 < 0) ++ return ret1; + + return ret; + } +@@ -725,7 +712,7 @@ qca8k_mdio_read(struct mii_bus *salve_bu + if (ret) + goto exit; + +- val = qca8k_mii_read32(bus, 0x10 | r2, r1); ++ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); + + exit: + /* even if the busy_wait timeouts try to clear the MASTER_EN */ +@@ -733,10 +720,10 @@ exit: + + mutex_unlock(&bus->mdio_lock); + +- if (val >= 0) +- val &= QCA8K_MDIO_MASTER_DATA_MASK; ++ if (ret >= 0) ++ ret = val & QCA8K_MDIO_MASTER_DATA_MASK; + +- return val; ++ return ret; + } + + static int +@@ -1211,7 +1198,7 @@ qca8k_phylink_mac_config(struct dsa_swit + qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); + + /* Enable/disable SerDes auto-negotiation as necessary */ +- val = qca8k_read(priv, QCA8K_REG_PWS); ++ qca8k_read(priv, QCA8K_REG_PWS, &val); + if (phylink_autoneg_inband(mode)) + val &= ~QCA8K_PWS_SERDES_AEN_DIS; + else +@@ -1219,7 +1206,7 @@ qca8k_phylink_mac_config(struct dsa_swit + qca8k_write(priv, QCA8K_REG_PWS, val); + + /* Configure the SGMII parameters */ +- val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL); ++ qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); + + val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | + QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; +@@ -1314,10 +1301,11 @@ qca8k_phylink_mac_link_state(struct dsa_ + { + struct qca8k_priv *priv = ds->priv; + u32 reg; ++ int ret; + +- reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port)); +- if (reg < 0) +- return reg; ++ ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), ®); ++ if (ret < 0) ++ return ret; + + state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); + state->an_complete = state->link; +@@ -1419,19 +1407,20 @@ qca8k_get_ethtool_stats(struct dsa_switc + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + const struct qca8k_mib_desc *mib; + u32 reg, i, val; +- u64 hi; ++ u64 hi = 0; ++ int ret; + + for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { + mib = &ar8327_mib[i]; + reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; + +- val = qca8k_read(priv, reg); +- if (val < 0) ++ ret = qca8k_read(priv, reg, &val); ++ if (ret < 0) + continue; + + if (mib->size == 2) { +- hi = qca8k_read(priv, reg + 4); +- if (hi < 0) ++ ret = qca8k_read(priv, reg + 4, (u32 *)&hi); ++ if (ret < 0) + continue; + } + +@@ -1459,7 +1448,7 @@ qca8k_set_mac_eee(struct dsa_switch *ds, + int ret; + + mutex_lock(&priv->reg_mutex); +- reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); ++ ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®); + if (reg < 0) { + ret = reg; + goto exit; +@@ -1802,14 +1791,15 @@ static int qca8k_read_switch_id(struct q + const struct qca8k_match_data *data; + u32 val; + u8 id; ++ int ret; + + /* get the switches ID from the compatible */ + data = of_device_get_match_data(priv->dev); + if (!data) + return -ENODEV; + +- val = qca8k_read(priv, QCA8K_REG_MASK_CTRL); +- if (val < 0) ++ ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val); ++ if (ret < 0) + return -ENODEV; + + id = QCA8K_MASK_CTRL_DEVICE_ID(val & QCA8K_MASK_CTRL_DEVICE_ID_MASK); diff --git a/target/linux/generic/backport-5.10/737-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch b/target/linux/generic/backport-5.10/737-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch new file mode 100644 index 0000000000..d20da5b85e --- /dev/null +++ b/target/linux/generic/backport-5.10/737-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch @@ -0,0 +1,47 @@ +From 9fe99de01440d9ede74d447ac76e9c445d8daae9 Mon Sep 17 00:00:00 2001 +From: Yang Yingliang +Date: Sat, 29 May 2021 11:04:39 +0800 +Subject: [PATCH] net: dsa: qca8k: add missing check return value in + qca8k_phylink_mac_config() + +Now we can check qca8k_read() return value correctly, so if +it fails, we need return directly. + +Signed-off-by: Yang Yingliang +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/qca8k.c | 9 +++++++-- + 1 file changed, 7 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1128,6 +1128,7 @@ qca8k_phylink_mac_config(struct dsa_swit + { + struct qca8k_priv *priv = ds->priv; + u32 reg, val; ++ int ret; + + switch (port) { + case 0: /* 1st CPU port */ +@@ -1198,7 +1199,9 @@ qca8k_phylink_mac_config(struct dsa_swit + qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); + + /* Enable/disable SerDes auto-negotiation as necessary */ +- qca8k_read(priv, QCA8K_REG_PWS, &val); ++ ret = qca8k_read(priv, QCA8K_REG_PWS, &val); ++ if (ret) ++ return; + if (phylink_autoneg_inband(mode)) + val &= ~QCA8K_PWS_SERDES_AEN_DIS; + else +@@ -1206,7 +1209,9 @@ qca8k_phylink_mac_config(struct dsa_swit + qca8k_write(priv, QCA8K_REG_PWS, val); + + /* Configure the SGMII parameters */ +- qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); ++ ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); ++ if (ret) ++ return; + + val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | + QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; diff --git a/target/linux/generic/backport-5.10/738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch b/target/linux/generic/backport-5.10/738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch new file mode 100644 index 0000000000..429d5d50f0 --- /dev/null +++ b/target/linux/generic/backport-5.10/738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch @@ -0,0 +1,47 @@ +aFrom aa3d020b22cb844ab7bdbb9e5d861a64666e2b74 Mon Sep 17 00:00:00 2001 +From: Dan Carpenter +Date: Wed, 9 Jun 2021 12:52:12 +0300 +Subject: [PATCH] net: dsa: qca8k: fix an endian bug in + qca8k_get_ethtool_stats() + +The "hi" variable is a u64 but the qca8k_read() writes to the top 32 +bits of it. That will work on little endian systems but it's a bit +subtle. It's cleaner to make declare "hi" as a u32. We will still need +to cast it when we shift it later on in the function but that's fine. + +Fixes: 7c9896e37807 ("net: dsa: qca8k: check return value of read functions correctly") +Signed-off-by: Dan Carpenter +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 6 +++--- + 1 file changed, 3 insertions(+), 3 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1412,7 +1412,7 @@ qca8k_get_ethtool_stats(struct dsa_switc + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; + const struct qca8k_mib_desc *mib; + u32 reg, i, val; +- u64 hi = 0; ++ u32 hi = 0; + int ret; + + for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { +@@ -1424,14 +1424,14 @@ qca8k_get_ethtool_stats(struct dsa_switc + continue; + + if (mib->size == 2) { +- ret = qca8k_read(priv, reg + 4, (u32 *)&hi); ++ ret = qca8k_read(priv, reg + 4, &hi); + if (ret < 0) + continue; + } + + data[i] = val; + if (mib->size == 2) +- data[i] |= hi << 32; ++ data[i] |= (u64)hi << 32; + } + } + diff --git a/target/linux/generic/backport-5.10/738-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch b/target/linux/generic/backport-5.10/738-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch new file mode 100644 index 0000000000..c58f79cd8b --- /dev/null +++ b/target/linux/generic/backport-5.10/738-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch @@ -0,0 +1,31 @@ +From 3d0167f2a627528032821cdeb78b4eab0510460f Mon Sep 17 00:00:00 2001 +From: Dan Carpenter +Date: Wed, 9 Jun 2021 12:53:03 +0300 +Subject: [PATCH] net: dsa: qca8k: check the correct variable in + qca8k_set_mac_eee() + +This code check "reg" but "ret" was intended so the error handling will +never trigger. + +Fixes: 7c9896e37807 ("net: dsa: qca8k: check return value of read functions correctly") +Signed-off-by: Dan Carpenter +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 4 +--- + 1 file changed, 1 insertion(+), 3 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1454,10 +1454,8 @@ qca8k_set_mac_eee(struct dsa_switch *ds, + + mutex_lock(&priv->reg_mutex); + ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®); +- if (reg < 0) { +- ret = reg; ++ if (ret < 0) + goto exit; +- } + + if (eee->eee_enabled) + reg |= lpi_en; diff --git a/target/linux/generic/backport-5.10/739-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch b/target/linux/generic/backport-5.10/739-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch new file mode 100644 index 0000000000..1e293d3a0b --- /dev/null +++ b/target/linux/generic/backport-5.10/739-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch @@ -0,0 +1,80 @@ +From ce062a0adbfe933b1932235fdfd874c4c91d1bb0 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sat, 11 Sep 2021 17:50:09 +0200 +Subject: net: dsa: qca8k: fix kernel panic with legacy mdio mapping + +When the mdio legacy mapping is used the mii_bus priv registered by DSA +refer to the dsa switch struct instead of the qca8k_priv struct and +causes a kernel panic. Create dedicated function when the internal +dedicated mdio driver is used to properly handle the 2 different +implementation. + +Fixes: 759bafb8a322 ("net: dsa: qca8k: add support for internal phy and internal mdio") +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 30 ++++++++++++++++++++++-------- + 1 file changed, 22 insertions(+), 8 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -643,10 +643,8 @@ qca8k_mdio_busy_wait(struct mii_bus *bus + } + + static int +-qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) ++qca8k_mdio_write(struct mii_bus *bus, int phy, int regnum, u16 data) + { +- struct qca8k_priv *priv = salve_bus->priv; +- struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 val; + int ret; +@@ -682,10 +680,8 @@ exit: + } + + static int +-qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) ++qca8k_mdio_read(struct mii_bus *bus, int phy, int regnum) + { +- struct qca8k_priv *priv = salve_bus->priv; +- struct mii_bus *bus = priv->bus; + u16 r1, r2, page; + u32 val; + int ret; +@@ -727,6 +723,24 @@ exit: + } + + static int ++qca8k_internal_mdio_write(struct mii_bus *slave_bus, int phy, int regnum, u16 data) ++{ ++ struct qca8k_priv *priv = slave_bus->priv; ++ struct mii_bus *bus = priv->bus; ++ ++ return qca8k_mdio_write(bus, phy, regnum, data); ++} ++ ++static int ++qca8k_internal_mdio_read(struct mii_bus *slave_bus, int phy, int regnum) ++{ ++ struct qca8k_priv *priv = slave_bus->priv; ++ struct mii_bus *bus = priv->bus; ++ ++ return qca8k_mdio_read(bus, phy, regnum); ++} ++ ++static int + qca8k_phy_write(struct dsa_switch *ds, int port, int regnum, u16 data) + { + struct qca8k_priv *priv = ds->priv; +@@ -775,8 +789,8 @@ qca8k_mdio_register(struct qca8k_priv *p + + bus->priv = (void *)priv; + bus->name = "qca8k slave mii"; +- bus->read = qca8k_mdio_read; +- bus->write = qca8k_mdio_write; ++ bus->read = qca8k_internal_mdio_read; ++ bus->write = qca8k_internal_mdio_write; + snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d", + ds->index); + diff --git a/target/linux/generic/backport-5.10/740-v5.12-net-phy-Add-100-base-x-mode.patch b/target/linux/generic/backport-5.10/740-v5.12-net-phy-Add-100-base-x-mode.patch deleted file mode 100644 index 5c7f97ea90..0000000000 --- a/target/linux/generic/backport-5.10/740-v5.12-net-phy-Add-100-base-x-mode.patch +++ /dev/null @@ -1,56 +0,0 @@ -From b1ae3587d16a8c8fc9453e147c8708d6f006ffbb Mon Sep 17 00:00:00 2001 -From: Bjarni Jonasson -Date: Wed, 13 Jan 2021 12:56:25 +0100 -Subject: [PATCH] net: phy: Add 100 base-x mode - -Sparx-5 supports this mode and it is missing in the PHY core. - -Signed-off-by: Bjarni Jonasson -Reviewed-by: Russell King -Signed-off-by: Jakub Kicinski ---- - Documentation/networking/phy.rst | 5 +++++ - include/linux/phy.h | 4 ++++ - 2 files changed, 9 insertions(+) - ---- a/Documentation/networking/phy.rst -+++ b/Documentation/networking/phy.rst -@@ -286,6 +286,11 @@ Some of the interface modes are describe - Note: due to legacy usage, some 10GBASE-R usage incorrectly makes - use of this definition. - -+``PHY_INTERFACE_MODE_100BASEX`` -+ This defines IEEE 802.3 Clause 24. The link operates at a fixed data -+ rate of 125Mpbs using a 4B/5B encoding scheme, resulting in an underlying -+ data rate of 100Mpbs. -+ - Pause frames / flow control - =========================== - ---- a/include/linux/phy.h -+++ b/include/linux/phy.h -@@ -104,6 +104,7 @@ extern const int phy_10gbit_features_arr - * @PHY_INTERFACE_MODE_MOCA: Multimedia over Coax - * @PHY_INTERFACE_MODE_QSGMII: Quad SGMII - * @PHY_INTERFACE_MODE_TRGMII: Turbo RGMII -+ * @PHY_INTERFACE_MODE_100BASEX: 100 BaseX - * @PHY_INTERFACE_MODE_1000BASEX: 1000 BaseX - * @PHY_INTERFACE_MODE_2500BASEX: 2500 BaseX - * @PHY_INTERFACE_MODE_RXAUI: Reduced XAUI -@@ -135,6 +136,7 @@ typedef enum { - PHY_INTERFACE_MODE_MOCA, - PHY_INTERFACE_MODE_QSGMII, - PHY_INTERFACE_MODE_TRGMII, -+ PHY_INTERFACE_MODE_100BASEX, - PHY_INTERFACE_MODE_1000BASEX, - PHY_INTERFACE_MODE_2500BASEX, - PHY_INTERFACE_MODE_RXAUI, -@@ -217,6 +219,8 @@ static inline const char *phy_modes(phy_ - return "usxgmii"; - case PHY_INTERFACE_MODE_10GKR: - return "10gbase-kr"; -+ case PHY_INTERFACE_MODE_100BASEX: -+ return "100base-x"; - default: - return "unknown"; - } diff --git a/target/linux/generic/backport-5.10/740-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch b/target/linux/generic/backport-5.10/740-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch new file mode 100644 index 0000000000..91cf55b18a --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch @@ -0,0 +1,65 @@ +From ee47ed08d75e8f16b3cf882061ee19c2ea19dd6c Mon Sep 17 00:00:00 2001 +From: Florian Fainelli +Date: Wed, 10 Mar 2021 10:52:26 -0800 +Subject: [PATCH] net: dsa: b53: Add debug prints in b53_vlan_enable() + +Having dynamic debug prints in b53_vlan_enable() has been helpful to +uncover a recent but update the function to indicate the port being +configured (or -1 for initial setup) and include the global VLAN enabled +and VLAN filtering enable status. + +Signed-off-by: Florian Fainelli +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_common.c | 11 +++++++---- + 1 file changed, 7 insertions(+), 4 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -349,7 +349,7 @@ static void b53_set_forwarding(struct b5 + b53_write8(dev, B53_CTRL_PAGE, B53_IP_MULTICAST_CTRL, mgmt); + } + +-static void b53_enable_vlan(struct b53_device *dev, bool enable, ++static void b53_enable_vlan(struct b53_device *dev, int port, bool enable, + bool enable_filtering) + { + u8 mgmt, vc0, vc1, vc4 = 0, vc5; +@@ -431,6 +431,9 @@ static void b53_enable_vlan(struct b53_d + b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt); + + dev->vlan_enabled = enable; ++ ++ dev_dbg(dev->dev, "Port %d VLAN enabled: %d, filtering: %d\n", ++ port, enable, enable_filtering); + } + + static int b53_set_jumbo(struct b53_device *dev, bool enable, bool allow_10_100) +@@ -708,7 +711,7 @@ int b53_configure_vlan(struct dsa_switch + b53_do_vlan_op(dev, VTA_CMD_CLEAR); + } + +- b53_enable_vlan(dev, dev->vlan_enabled, ds->vlan_filtering); ++ b53_enable_vlan(dev, -1, dev->vlan_enabled, ds->vlan_filtering); + + b53_for_each_port(dev, i) + b53_write16(dev, B53_VLAN_PAGE, +@@ -1390,7 +1393,7 @@ int b53_vlan_filtering(struct dsa_switch + if (switchdev_trans_ph_prepare(trans)) + return 0; + +- b53_enable_vlan(dev, dev->vlan_enabled, vlan_filtering); ++ b53_enable_vlan(dev, port, dev->vlan_enabled, vlan_filtering); + + return 0; + } +@@ -1415,7 +1418,7 @@ int b53_vlan_prepare(struct dsa_switch * + if (vlan->vid_end >= dev->num_vlans) + return -ERANGE; + +- b53_enable_vlan(dev, true, ds->vlan_filtering); ++ b53_enable_vlan(dev, port, true, ds->vlan_filtering); + + return 0; + } diff --git a/target/linux/generic/backport-5.10/740-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch b/target/linux/generic/backport-5.10/740-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch new file mode 100644 index 0000000000..56579b2d36 --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch @@ -0,0 +1,41 @@ +From 6d16eadab6db0c1d61e59fee7ed1ecc2d10269be Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= +Date: Mon, 15 Mar 2021 15:14:23 +0100 +Subject: [PATCH] net: dsa: b53: spi: allow device tree probing +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add missing of_match_table to allow device tree probing. + +Signed-off-by: Álvaro Fernández Rojas +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_spi.c | 13 +++++++++++++ + 1 file changed, 13 insertions(+) + +--- a/drivers/net/dsa/b53/b53_spi.c ++++ b/drivers/net/dsa/b53/b53_spi.c +@@ -324,9 +324,22 @@ static int b53_spi_remove(struct spi_dev + return 0; + } + ++static const struct of_device_id b53_spi_of_match[] = { ++ { .compatible = "brcm,bcm5325" }, ++ { .compatible = "brcm,bcm5365" }, ++ { .compatible = "brcm,bcm5395" }, ++ { .compatible = "brcm,bcm5397" }, ++ { .compatible = "brcm,bcm5398" }, ++ { .compatible = "brcm,bcm53115" }, ++ { .compatible = "brcm,bcm53125" }, ++ { .compatible = "brcm,bcm53128" }, ++ { /* sentinel */ } ++}; ++ + static struct spi_driver b53_spi_driver = { + .driver = { + .name = "b53-switch", ++ .of_match_table = b53_spi_of_match, + }, + .probe = b53_spi_probe, + .remove = b53_spi_remove, diff --git a/target/linux/generic/backport-5.10/740-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch b/target/linux/generic/backport-5.10/740-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch new file mode 100644 index 0000000000..99eced1b6a --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch @@ -0,0 +1,31 @@ +From ad426d7d966b525b73ed5a1842dd830312bbba71 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= +Date: Wed, 17 Mar 2021 09:42:01 +0100 +Subject: [PATCH] net: dsa: b53: relax is63xx() condition +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +BCM63xx switches are present on bcm63xx and bmips devices. + +Signed-off-by: Álvaro Fernández Rojas +Acked-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_priv.h | 4 ---- + 1 file changed, 4 deletions(-) + +--- a/drivers/net/dsa/b53/b53_priv.h ++++ b/drivers/net/dsa/b53/b53_priv.h +@@ -186,11 +186,7 @@ static inline int is531x5(struct b53_dev + + static inline int is63xx(struct b53_device *dev) + { +-#ifdef CONFIG_BCM63XX + return dev->chip_id == BCM63XX_DEVICE_ID; +-#else +- return 0; +-#endif + } + + static inline int is5301x(struct b53_device *dev) diff --git a/target/linux/generic/backport-5.10/740-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch b/target/linux/generic/backport-5.10/740-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch new file mode 100644 index 0000000000..3b7d8f37cd --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch @@ -0,0 +1,180 @@ +From 964dbf186eaa84d409c359ddf09c827a3fbe8228 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= +Date: Wed, 17 Mar 2021 11:29:26 +0100 +Subject: [PATCH] net: dsa: tag_brcm: add support for legacy tags +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM. +These tags are used on BCM5325, BCM5365 and BCM63xx switches. + +Signed-off-by: Álvaro Fernández Rojas +Signed-off-by: David S. Miller +--- + include/net/dsa.h | 2 + + net/dsa/Kconfig | 7 +++ + net/dsa/tag_brcm.c | 107 +++++++++++++++++++++++++++++++++++++++++++-- + 3 files changed, 113 insertions(+), 3 deletions(-) + +--- a/include/net/dsa.h ++++ b/include/net/dsa.h +@@ -45,10 +45,12 @@ struct phylink_link_state; + #define DSA_TAG_PROTO_OCELOT_VALUE 15 + #define DSA_TAG_PROTO_AR9331_VALUE 16 + #define DSA_TAG_PROTO_RTL4_A_VALUE 17 ++#define DSA_TAG_PROTO_BRCM_LEGACY_VALUE 22 + + enum dsa_tag_protocol { + DSA_TAG_PROTO_NONE = DSA_TAG_PROTO_NONE_VALUE, + DSA_TAG_PROTO_BRCM = DSA_TAG_PROTO_BRCM_VALUE, ++ DSA_TAG_PROTO_BRCM_LEGACY = DSA_TAG_PROTO_BRCM_LEGACY_VALUE, + DSA_TAG_PROTO_BRCM_PREPEND = DSA_TAG_PROTO_BRCM_PREPEND_VALUE, + DSA_TAG_PROTO_DSA = DSA_TAG_PROTO_DSA_VALUE, + DSA_TAG_PROTO_EDSA = DSA_TAG_PROTO_EDSA_VALUE, +--- a/net/dsa/Kconfig ++++ b/net/dsa/Kconfig +@@ -47,6 +47,13 @@ config NET_DSA_TAG_BRCM + Say Y if you want to enable support for tagging frames for the + Broadcom switches which place the tag after the MAC source address. + ++config NET_DSA_TAG_BRCM_LEGACY ++ tristate "Tag driver for Broadcom legacy switches using in-frame headers" ++ select NET_DSA_TAG_BRCM_COMMON ++ help ++ Say Y if you want to enable support for tagging frames for the ++ Broadcom legacy switches which place the tag after the MAC source ++ address. + + config NET_DSA_TAG_BRCM_PREPEND + tristate "Tag driver for Broadcom switches using prepended headers" +--- a/net/dsa/tag_brcm.c ++++ b/net/dsa/tag_brcm.c +@@ -11,9 +11,26 @@ + + #include "dsa_priv.h" + +-/* This tag length is 4 bytes, older ones were 6 bytes, we do not +- * handle them +- */ ++/* Legacy Broadcom tag (6 bytes) */ ++#define BRCM_LEG_TAG_LEN 6 ++ ++/* Type fields */ ++/* 1st byte in the tag */ ++#define BRCM_LEG_TYPE_HI 0x88 ++/* 2nd byte in the tag */ ++#define BRCM_LEG_TYPE_LO 0x74 ++ ++/* Tag fields */ ++/* 3rd byte in the tag */ ++#define BRCM_LEG_UNICAST (0 << 5) ++#define BRCM_LEG_MULTICAST (1 << 5) ++#define BRCM_LEG_EGRESS (2 << 5) ++#define BRCM_LEG_INGRESS (3 << 5) ++ ++/* 6th byte in the tag */ ++#define BRCM_LEG_PORT_ID (0xf) ++ ++/* Newer Broadcom tag (4 bytes) */ + #define BRCM_TAG_LEN 4 + + /* Tag is constructed and desconstructed using byte by byte access +@@ -194,6 +211,87 @@ DSA_TAG_DRIVER(brcm_netdev_ops); + MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_BRCM); + #endif + ++#if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_LEGACY) ++static struct sk_buff *brcm_leg_tag_xmit(struct sk_buff *skb, ++ struct net_device *dev) ++{ ++ struct dsa_port *dp = dsa_slave_to_port(dev); ++ u8 *brcm_tag; ++ ++ /* The Ethernet switch we are interfaced with needs packets to be at ++ * least 64 bytes (including FCS) otherwise they will be discarded when ++ * they enter the switch port logic. When Broadcom tags are enabled, we ++ * need to make sure that packets are at least 70 bytes ++ * (including FCS and tag) because the length verification is done after ++ * the Broadcom tag is stripped off the ingress packet. ++ * ++ * Let dsa_slave_xmit() free the SKB ++ */ ++ if (__skb_put_padto(skb, ETH_ZLEN + BRCM_LEG_TAG_LEN, false)) ++ return NULL; ++ ++ skb_push(skb, BRCM_LEG_TAG_LEN); ++ ++ memmove(skb->data, skb->data + BRCM_LEG_TAG_LEN, 2 * ETH_ALEN); ++ ++ brcm_tag = skb->data + 2 * ETH_ALEN; ++ ++ /* Broadcom tag type */ ++ brcm_tag[0] = BRCM_LEG_TYPE_HI; ++ brcm_tag[1] = BRCM_LEG_TYPE_LO; ++ ++ /* Broadcom tag value */ ++ brcm_tag[2] = BRCM_LEG_EGRESS; ++ brcm_tag[3] = 0; ++ brcm_tag[4] = 0; ++ brcm_tag[5] = dp->index & BRCM_LEG_PORT_ID; ++ ++ return skb; ++} ++ ++static struct sk_buff *brcm_leg_tag_rcv(struct sk_buff *skb, ++ struct net_device *dev, ++ struct packet_type *pt) ++{ ++ int source_port; ++ u8 *brcm_tag; ++ ++ if (unlikely(!pskb_may_pull(skb, BRCM_LEG_PORT_ID))) ++ return NULL; ++ ++ brcm_tag = skb->data - 2; ++ ++ source_port = brcm_tag[5] & BRCM_LEG_PORT_ID; ++ ++ skb->dev = dsa_master_find_slave(dev, 0, source_port); ++ if (!skb->dev) ++ return NULL; ++ ++ /* Remove Broadcom tag and update checksum */ ++ skb_pull_rcsum(skb, BRCM_LEG_TAG_LEN); ++ ++ skb->offload_fwd_mark = 1; ++ ++ /* Move the Ethernet DA and SA */ ++ memmove(skb->data - ETH_HLEN, ++ skb->data - ETH_HLEN - BRCM_LEG_TAG_LEN, ++ 2 * ETH_ALEN); ++ ++ return skb; ++} ++ ++static const struct dsa_device_ops brcm_legacy_netdev_ops = { ++ .name = "brcm-legacy", ++ .proto = DSA_TAG_PROTO_BRCM_LEGACY, ++ .xmit = brcm_leg_tag_xmit, ++ .rcv = brcm_leg_tag_rcv, ++ .overhead = BRCM_LEG_TAG_LEN, ++}; ++ ++DSA_TAG_DRIVER(brcm_legacy_netdev_ops); ++MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_BRCM_LEGACY); ++#endif /* CONFIG_NET_DSA_TAG_BRCM_LEGACY */ ++ + #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_PREPEND) + static struct sk_buff *brcm_tag_xmit_prepend(struct sk_buff *skb, + struct net_device *dev) +@@ -226,6 +324,9 @@ static struct dsa_tag_driver *dsa_tag_dr + #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM) + &DSA_TAG_DRIVER_NAME(brcm_netdev_ops), + #endif ++#if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_LEGACY) ++ &DSA_TAG_DRIVER_NAME(brcm_legacy_netdev_ops), ++#endif + #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_PREPEND) + &DSA_TAG_DRIVER_NAME(brcm_prepend_netdev_ops), + #endif diff --git a/target/linux/generic/backport-5.10/740-v5.13-0005-net-dsa-b53-support-legacy-tags.patch b/target/linux/generic/backport-5.10/740-v5.13-0005-net-dsa-b53-support-legacy-tags.patch new file mode 100644 index 0000000000..838e78a057 --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0005-net-dsa-b53-support-legacy-tags.patch @@ -0,0 +1,53 @@ +From 46c5176c586c81306bf9e7024c13b95da775490f Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= +Date: Wed, 17 Mar 2021 11:29:27 +0100 +Subject: [PATCH] net: dsa: b53: support legacy tags +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +These tags are used on BCM5325, BCM5365 and BCM63xx switches. + +Signed-off-by: Álvaro Fernández Rojas +Acked-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/Kconfig | 1 + + drivers/net/dsa/b53/b53_common.c | 12 +++++++----- + 2 files changed, 8 insertions(+), 5 deletions(-) + +--- a/drivers/net/dsa/b53/Kconfig ++++ b/drivers/net/dsa/b53/Kconfig +@@ -3,6 +3,7 @@ menuconfig B53 + tristate "Broadcom BCM53xx managed switch support" + depends on NET_DSA + select NET_DSA_TAG_BRCM ++ select NET_DSA_TAG_BRCM_LEGACY + select NET_DSA_TAG_BRCM_PREPEND + help + This driver adds support for Broadcom managed switch chips. It supports +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -2024,15 +2024,17 @@ enum dsa_tag_protocol b53_get_tag_protoc + { + struct b53_device *dev = ds->priv; + +- /* Older models (5325, 5365) support a different tag format that we do +- * not support in net/dsa/tag_brcm.c yet. +- */ +- if (is5325(dev) || is5365(dev) || +- !b53_can_enable_brcm_tags(ds, port, mprot)) { ++ if (!b53_can_enable_brcm_tags(ds, port, mprot)) { + dev->tag_protocol = DSA_TAG_PROTO_NONE; + goto out; + } + ++ /* Older models require a different 6 byte tag */ ++ if (is5325(dev) || is5365(dev) || is63xx(dev)) { ++ dev->tag_protocol = DSA_TAG_PROTO_BRCM_LEGACY; ++ goto out; ++ } ++ + /* Broadcom BCM58xx chips have a flow accelerator on Port 8 + * which requires us to use the prepended Broadcom tag type + */ diff --git a/target/linux/generic/backport-5.10/740-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch b/target/linux/generic/backport-5.10/740-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch new file mode 100644 index 0000000000..c1014b20bc --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch @@ -0,0 +1,92 @@ +From a5538a777b73b35750ed1ffff8c1ef539e861624 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= +Date: Wed, 17 Mar 2021 10:23:17 +0100 +Subject: [PATCH] net: dsa: b53: mmap: Add device tree support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add device tree support to b53_mmap.c while keeping platform devices support. + +Signed-off-by: Álvaro Fernández Rojas +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_mmap.c | 55 ++++++++++++++++++++++++++++++++++ + 1 file changed, 55 insertions(+) + +--- a/drivers/net/dsa/b53/b53_mmap.c ++++ b/drivers/net/dsa/b53/b53_mmap.c +@@ -16,6 +16,7 @@ + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + ++#include + #include + #include + #include +@@ -228,11 +229,65 @@ static const struct b53_io_ops b53_mmap_ + .write64 = b53_mmap_write64, + }; + ++static int b53_mmap_probe_of(struct platform_device *pdev, ++ struct b53_platform_data **ppdata) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *of_ports, *of_port; ++ struct device *dev = &pdev->dev; ++ struct b53_platform_data *pdata; ++ void __iomem *mem; ++ ++ mem = devm_platform_ioremap_resource(pdev, 0); ++ if (IS_ERR(mem)) ++ return PTR_ERR(mem); ++ ++ pdata = devm_kzalloc(dev, sizeof(struct b53_platform_data), ++ GFP_KERNEL); ++ if (!pdata) ++ return -ENOMEM; ++ ++ pdata->regs = mem; ++ pdata->chip_id = BCM63XX_DEVICE_ID; ++ pdata->big_endian = of_property_read_bool(np, "big-endian"); ++ ++ of_ports = of_get_child_by_name(np, "ports"); ++ if (!of_ports) { ++ dev_err(dev, "no ports child node found\n"); ++ return -EINVAL; ++ } ++ ++ for_each_available_child_of_node(of_ports, of_port) { ++ u32 reg; ++ ++ if (of_property_read_u32(of_port, "reg", ®)) ++ continue; ++ ++ if (reg < B53_CPU_PORT) ++ pdata->enabled_ports |= BIT(reg); ++ } ++ ++ of_node_put(of_ports); ++ *ppdata = pdata; ++ ++ return 0; ++} ++ + static int b53_mmap_probe(struct platform_device *pdev) + { ++ struct device_node *np = pdev->dev.of_node; + struct b53_platform_data *pdata = pdev->dev.platform_data; + struct b53_mmap_priv *priv; + struct b53_device *dev; ++ int ret; ++ ++ if (!pdata && np) { ++ ret = b53_mmap_probe_of(pdev, &pdata); ++ if (ret) { ++ dev_err(&pdev->dev, "OF probe error\n"); ++ return ret; ++ } ++ } + + if (!pdata) + return -EINVAL; diff --git a/target/linux/generic/backport-5.10/740-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch b/target/linux/generic/backport-5.10/740-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch new file mode 100644 index 0000000000..ea36755732 --- /dev/null +++ b/target/linux/generic/backport-5.10/740-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch @@ -0,0 +1,27 @@ +From 866f1577ba69bde2b9f36c300f603596c7d84a62 Mon Sep 17 00:00:00 2001 +From: Qinglang Miao +Date: Thu, 25 Mar 2021 17:19:54 +0800 +Subject: [PATCH] net: dsa: b53: spi: add missing MODULE_DEVICE_TABLE + +This patch adds missing MODULE_DEVICE_TABLE definition which generates +correct modalias for automatic loading of this driver when it is built +as an external module. + +Reported-by: Hulk Robot +Signed-off-by: Qinglang Miao +Acked-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_spi.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/net/dsa/b53/b53_spi.c ++++ b/drivers/net/dsa/b53/b53_spi.c +@@ -335,6 +335,7 @@ static const struct of_device_id b53_spi + { .compatible = "brcm,bcm53128" }, + { /* sentinel */ } + }; ++MODULE_DEVICE_TABLE(of, b53_spi_of_match); + + static struct spi_driver b53_spi_driver = { + .driver = { diff --git a/target/linux/generic/backport-5.10/741-v5.12-sfp-add-support-for-100-base-x-SFPs.patch b/target/linux/generic/backport-5.10/741-v5.12-sfp-add-support-for-100-base-x-SFPs.patch deleted file mode 100644 index 7d06c235d9..0000000000 --- a/target/linux/generic/backport-5.10/741-v5.12-sfp-add-support-for-100-base-x-SFPs.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 6e12f35cef6b8a458d7ecf507ae330e0bffaad8c Mon Sep 17 00:00:00 2001 -From: Bjarni Jonasson -Date: Wed, 13 Jan 2021 12:56:26 +0100 -Subject: [PATCH] sfp: add support for 100 base-x SFPs - -Add support for 100Base-FX, 100Base-LX, 100Base-PX and 100Base-BX10 modules -This is needed for Sparx-5 switch. - -Signed-off-by: Bjarni Jonasson -Reviewed-by: Russell King -Signed-off-by: Jakub Kicinski ---- - drivers/net/phy/sfp-bus.c | 9 +++++++++ - 1 file changed, 9 insertions(+) - ---- a/drivers/net/phy/sfp-bus.c -+++ b/drivers/net/phy/sfp-bus.c -@@ -280,6 +280,12 @@ void sfp_parse_support(struct sfp_bus *b - br_min <= 1300 && br_max >= 1200) - phylink_set(modes, 1000baseX_Full); - -+ /* 100Base-FX, 100Base-LX, 100Base-PX, 100Base-BX10 */ -+ if (id->base.e100_base_fx || id->base.e100_base_lx) -+ phylink_set(modes, 100baseFX_Full); -+ if ((id->base.e_base_px || id->base.e_base_bx10) && br_nom == 100) -+ phylink_set(modes, 100baseFX_Full); -+ - /* For active or passive cables, select the link modes - * based on the bit rates and the cable compliance bytes. - */ -@@ -399,6 +405,9 @@ phy_interface_t sfp_select_interface(str - if (phylink_test(link_modes, 1000baseX_Full)) - return PHY_INTERFACE_MODE_1000BASEX; - -+ if (phylink_test(link_modes, 100baseFX_Full)) -+ return PHY_INTERFACE_MODE_100BASEX; -+ - dev_warn(bus->sfp_dev, "Unable to ascertain link mode\n"); - - return PHY_INTERFACE_MODE_NA; diff --git a/target/linux/generic/backport-5.10/741-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch b/target/linux/generic/backport-5.10/741-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch new file mode 100644 index 0000000000..2a8def39b8 --- /dev/null +++ b/target/linux/generic/backport-5.10/741-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch @@ -0,0 +1,86 @@ +From 2c32a3d3c233b855943677609fe388f82b1f0975 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli +Date: Tue, 8 Jun 2021 14:22:04 -0700 +Subject: [PATCH] net: dsa: b53: Do not force CPU to be always tagged + +Commit ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all +VLANs") forced the CPU port to be always tagged in any VLAN membership. +This was necessary back then because we did not support Broadcom tags +for all configurations so the only way to differentiate tagged and +untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU +port into being always tagged. + +With most configurations enabling Broadcom tags, especially after +8fab459e69ab ("net: dsa: b53: Enable Broadcom tags for 531x5/539x +families") we do not need to apply this unconditional force tagging of +the CPU port in all VLANs. + +A helper function is introduced to faciliate the encapsulation of the +specific condition requiring the CPU port to be tagged in all VLANs and +the dsa_switch_ops::untag_bridge_pvid boolean is moved to when +dsa_switch_ops::setup is called when we have already determined the +tagging protocol we will be using. + +Reported-by: Matthew Hagan +Signed-off-by: Florian Fainelli +Reviewed-by: Vladimir Oltean +Tested-by: Matthew Hagan +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_common.c | 17 ++++++++++++++--- + 1 file changed, 14 insertions(+), 3 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -1049,6 +1049,11 @@ static int b53_setup(struct dsa_switch * + unsigned int port; + int ret; + ++ /* Request bridge PVID untagged when DSA_TAG_PROTO_NONE is set ++ * which forces the CPU port to be tagged in all VLANs. ++ */ ++ ds->untag_bridge_pvid = dev->tag_protocol == DSA_TAG_PROTO_NONE; ++ + ret = b53_reset_switch(dev); + if (ret) { + dev_err(ds->dev, "failed to reset switch\n"); +@@ -1423,6 +1428,13 @@ int b53_vlan_prepare(struct dsa_switch * + return 0; + } + EXPORT_SYMBOL(b53_vlan_prepare); ++ ++static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) ++{ ++ struct b53_device *dev = ds->priv; ++ ++ return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); ++} + + void b53_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +@@ -1442,7 +1454,7 @@ void b53_vlan_add(struct dsa_switch *ds, + untagged = true; + + vl->members |= BIT(port); +- if (untagged && !dsa_is_cpu_port(ds, port)) ++ if (untagged && !b53_vlan_port_needs_forced_tagged(ds, port)) + vl->untag |= BIT(port); + else + vl->untag &= ~BIT(port); +@@ -1480,7 +1492,7 @@ int b53_vlan_del(struct dsa_switch *ds, + if (pvid == vid) + pvid = b53_default_pvid(dev); + +- if (untagged && !dsa_is_cpu_port(ds, port)) ++ if (untagged && !b53_vlan_port_needs_forced_tagged(ds, port)) + vl->untag &= ~(BIT(port)); + + b53_set_vlan_entry(dev, vid, vl); +@@ -2644,7 +2656,6 @@ struct b53_device *b53_switch_alloc(stru + dev->ops = ops; + ds->ops = &b53_switch_ops; + ds->configure_vlan_while_not_filtering = true; +- ds->untag_bridge_pvid = true; + dev->vlan_enabled = ds->configure_vlan_while_not_filtering; + /* Let DSA handle the case were multiple bridges span the same switch + * device and different VLAN awareness settings are requested, which diff --git a/target/linux/generic/backport-5.10/741-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch b/target/linux/generic/backport-5.10/741-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch new file mode 100644 index 0000000000..ee3a71ffa5 --- /dev/null +++ b/target/linux/generic/backport-5.10/741-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch @@ -0,0 +1,30 @@ +From 11b57faf951cd3a570e3d9e463fc7c41023bc8c6 Mon Sep 17 00:00:00 2001 +From: Colin Ian King +Date: Tue, 15 Jun 2021 10:05:16 +0100 +Subject: [PATCH] net: dsa: b53: remove redundant null check on dev + +The pointer dev can never be null, the null check is redundant +and can be removed. Cleans up a static analysis warning that +pointer priv is dereferencing dev before dev is being null +checked. + +Addresses-Coverity: ("Dereference before null check") +Signed-off-by: Colin Ian King +Acked-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_srab.c | 3 +-- + 1 file changed, 1 insertion(+), 2 deletions(-) + +--- a/drivers/net/dsa/b53/b53_srab.c ++++ b/drivers/net/dsa/b53/b53_srab.c +@@ -632,8 +632,7 @@ static int b53_srab_remove(struct platfo + struct b53_srab_priv *priv = dev->priv; + + b53_srab_intr_set(priv, false); +- if (dev) +- b53_switch_remove(dev); ++ b53_switch_remove(dev); + + return 0; + } diff --git a/target/linux/generic/backport-5.10/741-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch b/target/linux/generic/backport-5.10/741-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch new file mode 100644 index 0000000000..df891d68ab --- /dev/null +++ b/target/linux/generic/backport-5.10/741-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch @@ -0,0 +1,71 @@ +From 64a81b24487f0d2fba0f033029eec2abc7d82cee Mon Sep 17 00:00:00 2001 +From: Florian Fainelli +Date: Mon, 21 Jun 2021 15:10:55 -0700 +Subject: [PATCH] net: dsa: b53: Create default VLAN entry explicitly + +In case CONFIG_VLAN_8021Q is not set, there will be no call down to the +b53 driver to ensure that the default PVID VLAN entry will be configured +with the appropriate untagged attribute towards the CPU port. We were +implicitly relying on dsa_slave_vlan_rx_add_vid() to do that for us, +instead make it explicit. + +Reported-by: Vladimir Oltean +Signed-off-by: Florian Fainelli +Reviewed-by: Vladimir Oltean +Signed-off-by: David S. Miller +--- + drivers/net/dsa/b53/b53_common.c | 27 +++++++++++++++++++-------- + 1 file changed, 19 insertions(+), 8 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -693,6 +693,13 @@ static u16 b53_default_pvid(struct b53_d + return 0; + } + ++static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) ++{ ++ struct b53_device *dev = ds->priv; ++ ++ return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); ++} ++ + int b53_configure_vlan(struct dsa_switch *ds) + { + struct b53_device *dev = ds->priv; +@@ -713,9 +720,20 @@ int b53_configure_vlan(struct dsa_switch + + b53_enable_vlan(dev, -1, dev->vlan_enabled, ds->vlan_filtering); + +- b53_for_each_port(dev, i) ++ /* Create an untagged VLAN entry for the default PVID in case ++ * CONFIG_VLAN_8021Q is disabled and there are no calls to ++ * dsa_slave_vlan_rx_add_vid() to create the default VLAN ++ * entry. Do this only when the tagging protocol is not ++ * DSA_TAG_PROTO_NONE ++ */ ++ b53_for_each_port(dev, i) { ++ v = &dev->vlans[def_vid]; ++ v->members |= BIT(i); ++ if (!b53_vlan_port_needs_forced_tagged(ds, i)) ++ v->untag = v->members; + b53_write16(dev, B53_VLAN_PAGE, + B53_VLAN_PORT_DEF_TAG(i), def_vid); ++ } + + /* Upon initial call we have not set-up any VLANs, but upon + * system resume, we need to restore all VLAN entries. +@@ -1429,13 +1447,6 @@ int b53_vlan_prepare(struct dsa_switch * + } + EXPORT_SYMBOL(b53_vlan_prepare); + +-static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) +-{ +- struct b53_device *dev = ds->priv; +- +- return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); +-} +- + void b53_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) + { diff --git a/target/linux/generic/backport-5.10/742-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch b/target/linux/generic/backport-5.10/742-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch deleted file mode 100644 index 7bf59267fa..0000000000 --- a/target/linux/generic/backport-5.10/742-v5.13-net-phy-marvell-refactor-HWMON-OOP-style.patch +++ /dev/null @@ -1,549 +0,0 @@ -From 41d26bf4aba070dfd2ab48866cc27a48ee6228c7 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Marek=20Beh=C3=BAn?= -Date: Tue, 20 Apr 2021 09:53:59 +0200 -Subject: [PATCH] net: phy: marvell: refactor HWMON OOP style -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Use a structure of Marvell PHY specific HWMON methods to reduce code -duplication. Store a pointer to this structure into the PHY driver's -driver_data member. - -Signed-off-by: Marek Behún -Signed-off-by: David S. Miller ---- - drivers/net/phy/marvell.c | 369 +++++++++++++------------------------- - 1 file changed, 125 insertions(+), 244 deletions(-) - ---- a/drivers/net/phy/marvell.c -+++ b/drivers/net/phy/marvell.c -@@ -2134,6 +2134,19 @@ static int marvell_vct7_cable_test_get_s - } - - #ifdef CONFIG_HWMON -+struct marvell_hwmon_ops { -+ int (*get_temp)(struct phy_device *phydev, long *temp); -+ int (*get_temp_critical)(struct phy_device *phydev, long *temp); -+ int (*set_temp_critical)(struct phy_device *phydev, long temp); -+ int (*get_temp_alarm)(struct phy_device *phydev, long *alarm); -+}; -+ -+static const struct marvell_hwmon_ops * -+to_marvell_hwmon_ops(const struct phy_device *phydev) -+{ -+ return phydev->drv->driver_data; -+} -+ - static int m88e1121_get_temp(struct phy_device *phydev, long *temp) - { - int oldpage; -@@ -2177,75 +2190,6 @@ error: - return phy_restore_page(phydev, oldpage, ret); - } - --static int m88e1121_hwmon_read(struct device *dev, -- enum hwmon_sensor_types type, -- u32 attr, int channel, long *temp) --{ -- struct phy_device *phydev = dev_get_drvdata(dev); -- int err; -- -- switch (attr) { -- case hwmon_temp_input: -- err = m88e1121_get_temp(phydev, temp); -- break; -- default: -- return -EOPNOTSUPP; -- } -- -- return err; --} -- --static umode_t m88e1121_hwmon_is_visible(const void *data, -- enum hwmon_sensor_types type, -- u32 attr, int channel) --{ -- if (type != hwmon_temp) -- return 0; -- -- switch (attr) { -- case hwmon_temp_input: -- return 0444; -- default: -- return 0; -- } --} -- --static u32 m88e1121_hwmon_chip_config[] = { -- HWMON_C_REGISTER_TZ, -- 0 --}; -- --static const struct hwmon_channel_info m88e1121_hwmon_chip = { -- .type = hwmon_chip, -- .config = m88e1121_hwmon_chip_config, --}; -- --static u32 m88e1121_hwmon_temp_config[] = { -- HWMON_T_INPUT, -- 0 --}; -- --static const struct hwmon_channel_info m88e1121_hwmon_temp = { -- .type = hwmon_temp, -- .config = m88e1121_hwmon_temp_config, --}; -- --static const struct hwmon_channel_info *m88e1121_hwmon_info[] = { -- &m88e1121_hwmon_chip, -- &m88e1121_hwmon_temp, -- NULL --}; -- --static const struct hwmon_ops m88e1121_hwmon_hwmon_ops = { -- .is_visible = m88e1121_hwmon_is_visible, -- .read = m88e1121_hwmon_read, --}; -- --static const struct hwmon_chip_info m88e1121_hwmon_chip_info = { -- .ops = &m88e1121_hwmon_hwmon_ops, -- .info = m88e1121_hwmon_info, --}; -- - static int m88e1510_get_temp(struct phy_device *phydev, long *temp) - { - int ret; -@@ -2308,92 +2252,6 @@ static int m88e1510_get_temp_alarm(struc - return 0; - } - --static int m88e1510_hwmon_read(struct device *dev, -- enum hwmon_sensor_types type, -- u32 attr, int channel, long *temp) --{ -- struct phy_device *phydev = dev_get_drvdata(dev); -- int err; -- -- switch (attr) { -- case hwmon_temp_input: -- err = m88e1510_get_temp(phydev, temp); -- break; -- case hwmon_temp_crit: -- err = m88e1510_get_temp_critical(phydev, temp); -- break; -- case hwmon_temp_max_alarm: -- err = m88e1510_get_temp_alarm(phydev, temp); -- break; -- default: -- return -EOPNOTSUPP; -- } -- -- return err; --} -- --static int m88e1510_hwmon_write(struct device *dev, -- enum hwmon_sensor_types type, -- u32 attr, int channel, long temp) --{ -- struct phy_device *phydev = dev_get_drvdata(dev); -- int err; -- -- switch (attr) { -- case hwmon_temp_crit: -- err = m88e1510_set_temp_critical(phydev, temp); -- break; -- default: -- return -EOPNOTSUPP; -- } -- return err; --} -- --static umode_t m88e1510_hwmon_is_visible(const void *data, -- enum hwmon_sensor_types type, -- u32 attr, int channel) --{ -- if (type != hwmon_temp) -- return 0; -- -- switch (attr) { -- case hwmon_temp_input: -- case hwmon_temp_max_alarm: -- return 0444; -- case hwmon_temp_crit: -- return 0644; -- default: -- return 0; -- } --} -- --static u32 m88e1510_hwmon_temp_config[] = { -- HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_MAX_ALARM, -- 0 --}; -- --static const struct hwmon_channel_info m88e1510_hwmon_temp = { -- .type = hwmon_temp, -- .config = m88e1510_hwmon_temp_config, --}; -- --static const struct hwmon_channel_info *m88e1510_hwmon_info[] = { -- &m88e1121_hwmon_chip, -- &m88e1510_hwmon_temp, -- NULL --}; -- --static const struct hwmon_ops m88e1510_hwmon_hwmon_ops = { -- .is_visible = m88e1510_hwmon_is_visible, -- .read = m88e1510_hwmon_read, -- .write = m88e1510_hwmon_write, --}; -- --static const struct hwmon_chip_info m88e1510_hwmon_chip_info = { -- .ops = &m88e1510_hwmon_hwmon_ops, -- .info = m88e1510_hwmon_info, --}; -- - static int m88e6390_get_temp(struct phy_device *phydev, long *temp) - { - int sum = 0; -@@ -2452,63 +2310,112 @@ error: - return ret; - } - --static int m88e6390_hwmon_read(struct device *dev, -- enum hwmon_sensor_types type, -- u32 attr, int channel, long *temp) -+static int marvell_hwmon_read(struct device *dev, enum hwmon_sensor_types type, -+ u32 attr, int channel, long *temp) - { - struct phy_device *phydev = dev_get_drvdata(dev); -- int err; -+ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); -+ int err = -EOPNOTSUPP; - - switch (attr) { - case hwmon_temp_input: -- err = m88e6390_get_temp(phydev, temp); -+ if (ops->get_temp) -+ err = ops->get_temp(phydev, temp); -+ break; -+ case hwmon_temp_crit: -+ if (ops->get_temp_critical) -+ err = ops->get_temp_critical(phydev, temp); -+ break; -+ case hwmon_temp_max_alarm: -+ if (ops->get_temp_alarm) -+ err = ops->get_temp_alarm(phydev, temp); -+ break; -+ } -+ -+ return err; -+} -+ -+static int marvell_hwmon_write(struct device *dev, enum hwmon_sensor_types type, -+ u32 attr, int channel, long temp) -+{ -+ struct phy_device *phydev = dev_get_drvdata(dev); -+ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); -+ int err = -EOPNOTSUPP; -+ -+ switch (attr) { -+ case hwmon_temp_crit: -+ if (ops->set_temp_critical) -+ err = ops->set_temp_critical(phydev, temp); - break; - default: -- return -EOPNOTSUPP; -+ fallthrough; - } - - return err; - } - --static umode_t m88e6390_hwmon_is_visible(const void *data, -- enum hwmon_sensor_types type, -- u32 attr, int channel) -+static umode_t marvell_hwmon_is_visible(const void *data, -+ enum hwmon_sensor_types type, -+ u32 attr, int channel) - { -+ const struct phy_device *phydev = data; -+ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); -+ - if (type != hwmon_temp) - return 0; - - switch (attr) { - case hwmon_temp_input: -- return 0444; -+ return ops->get_temp ? 0444 : 0; -+ case hwmon_temp_max_alarm: -+ return ops->get_temp_alarm ? 0444 : 0; -+ case hwmon_temp_crit: -+ return (ops->get_temp_critical ? 0444 : 0) | -+ (ops->set_temp_critical ? 0200 : 0); - default: - return 0; - } - } - --static u32 m88e6390_hwmon_temp_config[] = { -- HWMON_T_INPUT, -+static u32 marvell_hwmon_chip_config[] = { -+ HWMON_C_REGISTER_TZ, - 0 - }; - --static const struct hwmon_channel_info m88e6390_hwmon_temp = { -+static const struct hwmon_channel_info marvell_hwmon_chip = { -+ .type = hwmon_chip, -+ .config = marvell_hwmon_chip_config, -+}; -+ -+/* we can define HWMON_T_CRIT and HWMON_T_MAX_ALARM even though these are not -+ * defined for all PHYs, because the hwmon code checks whether the attributes -+ * exists via the .is_visible method -+ */ -+static u32 marvell_hwmon_temp_config[] = { -+ HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_MAX_ALARM, -+ 0 -+}; -+ -+static const struct hwmon_channel_info marvell_hwmon_temp = { - .type = hwmon_temp, -- .config = m88e6390_hwmon_temp_config, -+ .config = marvell_hwmon_temp_config, - }; - --static const struct hwmon_channel_info *m88e6390_hwmon_info[] = { -- &m88e1121_hwmon_chip, -- &m88e6390_hwmon_temp, -+static const struct hwmon_channel_info *marvell_hwmon_info[] = { -+ &marvell_hwmon_chip, -+ &marvell_hwmon_temp, - NULL - }; - --static const struct hwmon_ops m88e6390_hwmon_hwmon_ops = { -- .is_visible = m88e6390_hwmon_is_visible, -- .read = m88e6390_hwmon_read, -+static const struct hwmon_ops marvell_hwmon_hwmon_ops = { -+ .is_visible = marvell_hwmon_is_visible, -+ .read = marvell_hwmon_read, -+ .write = marvell_hwmon_write, - }; - --static const struct hwmon_chip_info m88e6390_hwmon_chip_info = { -- .ops = &m88e6390_hwmon_hwmon_ops, -- .info = m88e6390_hwmon_info, -+static const struct hwmon_chip_info marvell_hwmon_chip_info = { -+ .ops = &marvell_hwmon_hwmon_ops, -+ .info = marvell_hwmon_info, - }; - - static int marvell_hwmon_name(struct phy_device *phydev) -@@ -2531,49 +2438,48 @@ static int marvell_hwmon_name(struct phy - return 0; - } - --static int marvell_hwmon_probe(struct phy_device *phydev, -- const struct hwmon_chip_info *chip) -+static int marvell_hwmon_probe(struct phy_device *phydev) - { -+ const struct marvell_hwmon_ops *ops = to_marvell_hwmon_ops(phydev); - struct marvell_priv *priv = phydev->priv; - struct device *dev = &phydev->mdio.dev; - int err; - -+ if (!ops) -+ return 0; -+ - err = marvell_hwmon_name(phydev); - if (err) - return err; - - priv->hwmon_dev = devm_hwmon_device_register_with_info( -- dev, priv->hwmon_name, phydev, chip, NULL); -+ dev, priv->hwmon_name, phydev, &marvell_hwmon_chip_info, NULL); - - return PTR_ERR_OR_ZERO(priv->hwmon_dev); - } - --static int m88e1121_hwmon_probe(struct phy_device *phydev) --{ -- return marvell_hwmon_probe(phydev, &m88e1121_hwmon_chip_info); --} -+static const struct marvell_hwmon_ops m88e1121_hwmon_ops = { -+ .get_temp = m88e1121_get_temp, -+}; - --static int m88e1510_hwmon_probe(struct phy_device *phydev) --{ -- return marvell_hwmon_probe(phydev, &m88e1510_hwmon_chip_info); --} -+static const struct marvell_hwmon_ops m88e1510_hwmon_ops = { -+ .get_temp = m88e1510_get_temp, -+ .get_temp_critical = m88e1510_get_temp_critical, -+ .set_temp_critical = m88e1510_set_temp_critical, -+ .get_temp_alarm = m88e1510_get_temp_alarm, -+}; -+ -+static const struct marvell_hwmon_ops m88e6390_hwmon_ops = { -+ .get_temp = m88e6390_get_temp, -+}; -+ -+#define DEF_MARVELL_HWMON_OPS(s) (&(s)) - --static int m88e6390_hwmon_probe(struct phy_device *phydev) --{ -- return marvell_hwmon_probe(phydev, &m88e6390_hwmon_chip_info); --} - #else --static int m88e1121_hwmon_probe(struct phy_device *phydev) --{ -- return 0; --} - --static int m88e1510_hwmon_probe(struct phy_device *phydev) --{ -- return 0; --} -+#define DEF_MARVELL_HWMON_OPS(s) NULL - --static int m88e6390_hwmon_probe(struct phy_device *phydev) -+static int marvell_hwmon_probe(struct phy_device *phydev) - { - return 0; - } -@@ -2589,40 +2495,7 @@ static int marvell_probe(struct phy_devi - - phydev->priv = priv; - -- return 0; --} -- --static int m88e1121_probe(struct phy_device *phydev) --{ -- int err; -- -- err = marvell_probe(phydev); -- if (err) -- return err; -- -- return m88e1121_hwmon_probe(phydev); --} -- --static int m88e1510_probe(struct phy_device *phydev) --{ -- int err; -- -- err = marvell_probe(phydev); -- if (err) -- return err; -- -- return m88e1510_hwmon_probe(phydev); --} -- --static int m88e6390_probe(struct phy_device *phydev) --{ -- int err; -- -- err = marvell_probe(phydev); -- if (err) -- return err; -- -- return m88e6390_hwmon_probe(phydev); -+ return marvell_hwmon_probe(phydev); - } - - static struct phy_driver marvell_drivers[] = { -@@ -2707,8 +2580,9 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1121R, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1121R", -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1121_hwmon_ops), - /* PHY_GBIT_FEATURES */ -- .probe = m88e1121_probe, -+ .probe = marvell_probe, - .config_init = marvell_config_init, - .config_aneg = m88e1121_config_aneg, - .read_status = marvell_read_status, -@@ -2827,9 +2701,10 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1510, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1510", -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), - .features = PHY_GBIT_FIBRE_FEATURES, - .flags = PHY_POLL_CABLE_TEST, -- .probe = m88e1510_probe, -+ .probe = marvell_probe, - .config_init = m88e1510_config_init, - .config_aneg = m88e1510_config_aneg, - .read_status = marvell_read_status, -@@ -2856,9 +2731,10 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1540, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1540", -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), - /* PHY_GBIT_FEATURES */ - .flags = PHY_POLL_CABLE_TEST, -- .probe = m88e1510_probe, -+ .probe = marvell_probe, - .config_init = marvell_config_init, - .config_aneg = m88e1510_config_aneg, - .read_status = marvell_read_status, -@@ -2882,7 +2758,8 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1545, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1545", -- .probe = m88e1510_probe, -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), -+ .probe = marvell_probe, - /* PHY_GBIT_FEATURES */ - .flags = PHY_POLL_CABLE_TEST, - .config_init = marvell_config_init, -@@ -2928,9 +2805,10 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E6341_FAMILY, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E6341 Family", -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), - /* PHY_GBIT_FEATURES */ - .flags = PHY_POLL_CABLE_TEST, -- .probe = m88e1510_probe, -+ .probe = marvell_probe, - .config_init = marvell_config_init, - .config_aneg = m88e6390_config_aneg, - .read_status = marvell_read_status, -@@ -2954,9 +2832,10 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E6390_FAMILY, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E6390 Family", -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e6390_hwmon_ops), - /* PHY_GBIT_FEATURES */ - .flags = PHY_POLL_CABLE_TEST, -- .probe = m88e6390_probe, -+ .probe = marvell_probe, - .config_init = marvell_config_init, - .config_aneg = m88e6390_config_aneg, - .read_status = marvell_read_status, -@@ -2980,7 +2859,8 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1340S, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1340S", -- .probe = m88e1510_probe, -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), -+ .probe = marvell_probe, - /* PHY_GBIT_FEATURES */ - .config_init = marvell_config_init, - .config_aneg = m88e1510_config_aneg, -@@ -3002,7 +2882,8 @@ static struct phy_driver marvell_drivers - .phy_id = MARVELL_PHY_ID_88E1548P, - .phy_id_mask = MARVELL_PHY_ID_MASK, - .name = "Marvell 88E1548P", -- .probe = m88e1510_probe, -+ .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), -+ .probe = marvell_probe, - .features = PHY_GBIT_FIBRE_FEATURES, - .config_init = marvell_config_init, - .config_aneg = m88e1510_config_aneg, diff --git a/target/linux/generic/backport-5.10/742-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch b/target/linux/generic/backport-5.10/742-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch new file mode 100644 index 0000000000..16aa0711ad --- /dev/null +++ b/target/linux/generic/backport-5.10/742-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch @@ -0,0 +1,48 @@ +From 0ccf8511182436183c031e8a2f740ae91a02c625 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 14 Sep 2021 14:33:45 +0200 +Subject: net: phy: at803x: add support for qca 8327 internal phy + +Add support for qca8327 internal phy needed for correct init of the +switch port. It does use the same qca8337 function and reg just with a +different id. + +Signed-off-by: Ansuel Smith +Tested-by: Rosen Penev +Tested-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 15 +++++++++++++++ + 1 file changed, 15 insertions(+) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -1328,6 +1328,19 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, ++}, { ++ /* QCA8327 */ ++ .phy_id = QCA8327_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "QCA PHY 8327", ++ /* PHY_GBIT_FEATURES */ ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, + }, }; + + module_phy_driver(at803x_driver); +@@ -1338,6 +1351,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, ++ { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) }, ++ { PHY_ID_MATCH_EXACT(QCA8327_PHY_ID) }, + { } + }; + diff --git a/target/linux/generic/backport-5.10/743-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch b/target/linux/generic/backport-5.10/743-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch deleted file mode 100644 index 7fb78089f2..0000000000 --- a/target/linux/generic/backport-5.10/743-v5.15-net-phy-marvell-add-SFP-support-for-88E1510.patch +++ /dev/null @@ -1,161 +0,0 @@ -From b697d9d38a5a5ab405d7cc4743d39fe2c5d7517c Mon Sep 17 00:00:00 2001 -From: Ivan Bornyakov -Date: Thu, 12 Aug 2021 16:42:56 +0300 -Subject: [PATCH] net: phy: marvell: add SFP support for 88E1510 - -Add support for SFP cages connected to the Marvell 88E1512 transceiver. -88E1512 supports for SGMII/1000Base-X/100Base-FX media type with RGMII -on system interface. Configure PHY to appropriate mode depending on the -type of SFP inserted. On SFP removal configure PHY to the RGMII-copper -mode so RJ-45 port can still work. - -Signed-off-by: Ivan Bornyakov -Link: https://lore.kernel.org/r/20210812134256.2436-1-i.bornyakov@metrotek.ru -Signed-off-by: Jakub Kicinski ---- - drivers/net/phy/marvell.c | 105 +++++++++++++++++++++++++++++++++++++- - 1 file changed, 104 insertions(+), 1 deletion(-) - ---- a/drivers/net/phy/marvell.c -+++ b/drivers/net/phy/marvell.c -@@ -32,6 +32,7 @@ - #include - #include - #include -+#include - - #include - #include -@@ -46,6 +47,7 @@ - #define MII_MARVELL_MISC_TEST_PAGE 0x06 - #define MII_MARVELL_VCT7_PAGE 0x07 - #define MII_MARVELL_WOL_PAGE 0x11 -+#define MII_MARVELL_MODE_PAGE 0x12 - - #define MII_M1011_IEVENT 0x13 - #define MII_M1011_IEVENT_CLEAR 0x0000 -@@ -162,7 +164,14 @@ - - #define MII_88E1510_GEN_CTRL_REG_1 0x14 - #define MII_88E1510_GEN_CTRL_REG_1_MODE_MASK 0x7 -+#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII 0x0 /* RGMII to copper */ - #define MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII 0x1 /* SGMII to copper */ -+/* RGMII to 1000BASE-X */ -+#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X 0x2 -+/* RGMII to 100BASE-FX */ -+#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX 0x3 -+/* RGMII to SGMII */ -+#define MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII 0x4 - #define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */ - - #define MII_VCT5_TX_RX_MDI0_COUPLING 0x10 -@@ -2498,6 +2507,100 @@ static int marvell_probe(struct phy_devi - return marvell_hwmon_probe(phydev); - } - -+static int m88e1510_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) -+{ -+ struct phy_device *phydev = upstream; -+ phy_interface_t interface; -+ struct device *dev; -+ int oldpage; -+ int ret = 0; -+ u16 mode; -+ -+ __ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, }; -+ -+ dev = &phydev->mdio.dev; -+ -+ sfp_parse_support(phydev->sfp_bus, id, supported); -+ interface = sfp_select_interface(phydev->sfp_bus, supported); -+ -+ dev_info(dev, "%s SFP module inserted\n", phy_modes(interface)); -+ -+ switch (interface) { -+ case PHY_INTERFACE_MODE_1000BASEX: -+ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X; -+ -+ break; -+ case PHY_INTERFACE_MODE_100BASEX: -+ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX; -+ -+ break; -+ case PHY_INTERFACE_MODE_SGMII: -+ mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII; -+ -+ break; -+ default: -+ dev_err(dev, "Incompatible SFP module inserted\n"); -+ -+ return -EINVAL; -+ } -+ -+ oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE); -+ if (oldpage < 0) -+ goto error; -+ -+ ret = __phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1, -+ MII_88E1510_GEN_CTRL_REG_1_MODE_MASK, mode); -+ if (ret < 0) -+ goto error; -+ -+ ret = __phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1, -+ MII_88E1510_GEN_CTRL_REG_1_RESET); -+ -+error: -+ return phy_restore_page(phydev, oldpage, ret); -+} -+ -+static void m88e1510_sfp_remove(void *upstream) -+{ -+ struct phy_device *phydev = upstream; -+ int oldpage; -+ int ret = 0; -+ -+ oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE); -+ if (oldpage < 0) -+ goto error; -+ -+ ret = __phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1, -+ MII_88E1510_GEN_CTRL_REG_1_MODE_MASK, -+ MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII); -+ if (ret < 0) -+ goto error; -+ -+ ret = __phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1, -+ MII_88E1510_GEN_CTRL_REG_1_RESET); -+ -+error: -+ phy_restore_page(phydev, oldpage, ret); -+} -+ -+static const struct sfp_upstream_ops m88e1510_sfp_ops = { -+ .module_insert = m88e1510_sfp_insert, -+ .module_remove = m88e1510_sfp_remove, -+ .attach = phy_sfp_attach, -+ .detach = phy_sfp_detach, -+}; -+ -+static int m88e1510_probe(struct phy_device *phydev) -+{ -+ int err; -+ -+ err = marvell_probe(phydev); -+ if (err) -+ return err; -+ -+ return phy_sfp_probe(phydev, &m88e1510_sfp_ops); -+} -+ - static struct phy_driver marvell_drivers[] = { - { - .phy_id = MARVELL_PHY_ID_88E1101, -@@ -2704,7 +2807,7 @@ static struct phy_driver marvell_drivers - .driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops), - .features = PHY_GBIT_FIBRE_FEATURES, - .flags = PHY_POLL_CABLE_TEST, -- .probe = marvell_probe, -+ .probe = m88e1510_probe, - .config_init = m88e1510_config_init, - .config_aneg = m88e1510_config_aneg, - .read_status = marvell_read_status, diff --git a/target/linux/generic/backport-5.10/743-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch b/target/linux/generic/backport-5.10/743-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch new file mode 100644 index 0000000000..d80b5db714 --- /dev/null +++ b/target/linux/generic/backport-5.10/743-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch @@ -0,0 +1,131 @@ +From 983d96a9116a328668601555d96736261d33170c Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Sep 2021 14:03:51 +0200 +Subject: [PATCH] net: dsa: b53: Include all ports in "enabled_ports" +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Make "enabled_ports" bitfield contain all available switch ports +including a CPU port. This way there is no need for fixup during +initialization. + +For BCM53010, BCM53018 and BCM53019 include also other available ports. + +Signed-off-by: Rafał Miłecki +Reviewed-by: Florian Fainelli +Tested-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/b53/b53_common.c | 23 +++++++++++------------ + 1 file changed, 11 insertions(+), 12 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -2288,7 +2288,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5325_DEVICE_ID, + .dev_name = "BCM5325", + .vlans = 16, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x3f, + .arl_bins = 2, + .arl_buckets = 1024, + .imp_port = 5, +@@ -2299,7 +2299,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5365_DEVICE_ID, + .dev_name = "BCM5365", + .vlans = 256, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x3f, + .arl_bins = 2, + .arl_buckets = 1024, + .imp_port = 5, +@@ -2310,7 +2310,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5389_DEVICE_ID, + .dev_name = "BCM5389", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x11f, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2324,7 +2324,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5395_DEVICE_ID, + .dev_name = "BCM5395", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x11f, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2338,7 +2338,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5397_DEVICE_ID, + .dev_name = "BCM5397", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x11f, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2352,7 +2352,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM5398_DEVICE_ID, + .dev_name = "BCM5398", + .vlans = 4096, +- .enabled_ports = 0x7f, ++ .enabled_ports = 0x17f, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2366,7 +2366,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM53115_DEVICE_ID, + .dev_name = "BCM53115", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x11f, + .arl_bins = 4, + .arl_buckets = 1024, + .vta_regs = B53_VTA_REGS, +@@ -2380,7 +2380,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM53125_DEVICE_ID, + .dev_name = "BCM53125", + .vlans = 4096, +- .enabled_ports = 0xff, ++ .enabled_ports = 0x1ff, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2422,7 +2422,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM53010_DEVICE_ID, + .dev_name = "BCM53010", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x1bf, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2464,7 +2464,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM53018_DEVICE_ID, + .dev_name = "BCM53018", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x1bf, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2478,7 +2478,7 @@ static const struct b53_chip_data b53_sw + .chip_id = BCM53019_DEVICE_ID, + .dev_name = "BCM53019", + .vlans = 4096, +- .enabled_ports = 0x1f, ++ .enabled_ports = 0x1bf, + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +@@ -2605,7 +2605,6 @@ static int b53_switch_init(struct b53_de + dev->cpu_port = 5; + } + +- dev->enabled_ports |= BIT(dev->cpu_port); + dev->num_ports = fls(dev->enabled_ports); + + dev->ds->num_ports = min_t(unsigned int, dev->num_ports, DSA_MAX_PORTS); diff --git a/target/linux/generic/backport-5.10/743-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch b/target/linux/generic/backport-5.10/743-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch new file mode 100644 index 0000000000..4a4f8e940d --- /dev/null +++ b/target/linux/generic/backport-5.10/743-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch @@ -0,0 +1,42 @@ +From b290c6384afabbca5ae6e2af72fb1b2bc37922be Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Sep 2021 14:03:52 +0200 +Subject: [PATCH] net: dsa: b53: Drop BCM5301x workaround for a wrong CPU/IMP + port +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +On BCM5301x port 8 requires a fixed link when used. + +Years ago when b53 was an OpenWrt downstream driver (with configuration +based on sometimes bugged NVRAM) there was a need for a fixup. In case +of forcing fixed link for (incorrectly specified) port 5 the code had to +actually setup port 8 link. + +For upstream b53 driver with setup based on DT there is no need for that +workaround. In DT we have and require correct ports setup. + +Signed-off-by: Rafał Miłecki +Reviewed-by: Florian Fainelli +Tested-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/b53/b53_common.c | 6 ------ + 1 file changed, 6 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -1256,12 +1256,6 @@ static void b53_adjust_link(struct dsa_s + return; + } + } +- } else if (is5301x(dev)) { +- if (port != dev->cpu_port) { +- b53_force_port_config(dev, dev->cpu_port, 2000, +- DUPLEX_FULL, true, true); +- b53_force_link(dev, dev->cpu_port, 1); +- } + } + + /* Re-negotiate EEE if it was enabled already */ diff --git a/target/linux/generic/backport-5.10/743-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch b/target/linux/generic/backport-5.10/743-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch new file mode 100644 index 0000000000..3954ee4aac --- /dev/null +++ b/target/linux/generic/backport-5.10/743-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch @@ -0,0 +1,32 @@ +From 3ff26b29230c54fea2353b63124c589b61953e14 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Sep 2021 14:03:53 +0200 +Subject: [PATCH] net: dsa: b53: Improve flow control setup on BCM5301x +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +According to the Broadcom's reference driver flow control needs to be +enabled for any CPU switch port (5, 7 or 8 - depending on which one is +used). Current code makes it work only for the port 5. Use +dsa_is_cpu_port() which solved that problem. + +Signed-off-by: Rafał Miłecki +Reviewed-by: Florian Fainelli +Tested-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/b53/b53_common.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -1187,7 +1187,7 @@ static void b53_adjust_link(struct dsa_s + return; + + /* Enable flow control on BCM5301x's CPU port */ +- if (is5301x(dev) && port == dev->cpu_port) ++ if (is5301x(dev) && dsa_is_cpu_port(ds, port)) + tx_pause = rx_pause = true; + + if (phydev->pause) { diff --git a/target/linux/generic/backport-5.10/743-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch b/target/linux/generic/backport-5.10/743-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch new file mode 100644 index 0000000000..9e687b1488 --- /dev/null +++ b/target/linux/generic/backport-5.10/743-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch @@ -0,0 +1,205 @@ +From 7d5af56418d7d01e43247a33b6fe6492ea871923 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Date: Thu, 16 Sep 2021 14:03:54 +0200 +Subject: [PATCH] net: dsa: b53: Drop unused "cpu_port" field +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +It's set but never used anymore. + +Signed-off-by: Rafał Miłecki +Reviewed-by: Florian Fainelli +Tested-by: Florian Fainelli +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/b53/b53_common.c | 28 ---------------------------- + drivers/net/dsa/b53/b53_priv.h | 1 - + 2 files changed, 29 deletions(-) + +--- a/drivers/net/dsa/b53/b53_common.c ++++ b/drivers/net/dsa/b53/b53_common.c +@@ -2286,7 +2286,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 2, + .arl_buckets = 1024, + .imp_port = 5, +- .cpu_port = B53_CPU_PORT_25, + .duplex_reg = B53_DUPLEX_STAT_FE, + }, + { +@@ -2297,7 +2296,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 2, + .arl_buckets = 1024, + .imp_port = 5, +- .cpu_port = B53_CPU_PORT_25, + .duplex_reg = B53_DUPLEX_STAT_FE, + }, + { +@@ -2308,7 +2306,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2322,7 +2319,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2336,7 +2332,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS_9798, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2350,7 +2345,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS_9798, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2365,7 +2359,6 @@ static const struct b53_chip_data b53_sw + .arl_buckets = 1024, + .vta_regs = B53_VTA_REGS, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, + .jumbo_size_reg = B53_JUMBO_MAX_SIZE, +@@ -2378,7 +2371,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2392,7 +2384,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2406,7 +2397,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS_63XX, + .duplex_reg = B53_DUPLEX_STAT_63XX, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK_63XX, +@@ -2420,7 +2410,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2434,7 +2423,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2448,7 +2436,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2462,7 +2449,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2476,7 +2462,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2490,7 +2475,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2504,7 +2488,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2518,7 +2501,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 1024, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2532,7 +2514,6 @@ static const struct b53_chip_data b53_sw + .arl_bins = 4, + .arl_buckets = 256, + .imp_port = 8, +- .cpu_port = B53_CPU_PORT, + .vta_regs = B53_VTA_REGS, + .duplex_reg = B53_DUPLEX_STAT_GE, + .jumbo_pm_reg = B53_JUMBO_PORT_MASK, +@@ -2558,7 +2539,6 @@ static int b53_switch_init(struct b53_de + dev->vta_regs[2] = chip->vta_regs[2]; + dev->jumbo_pm_reg = chip->jumbo_pm_reg; + dev->imp_port = chip->imp_port; +- dev->cpu_port = chip->cpu_port; + dev->num_vlans = chip->vlans; + dev->num_arl_bins = chip->arl_bins; + dev->num_arl_buckets = chip->arl_buckets; +@@ -2590,13 +2570,6 @@ static int b53_switch_init(struct b53_de + break; + #endif + } +- } else if (dev->chip_id == BCM53115_DEVICE_ID) { +- u64 strap_value; +- +- b53_read48(dev, B53_STAT_PAGE, B53_STRAP_VALUE, &strap_value); +- /* use second IMP port if GMII is enabled */ +- if (strap_value & SV_GMII_CTRL_115) +- dev->cpu_port = 5; + } + + dev->num_ports = fls(dev->enabled_ports); +--- a/drivers/net/dsa/b53/b53_priv.h ++++ b/drivers/net/dsa/b53/b53_priv.h +@@ -123,7 +123,6 @@ struct b53_device { + /* used ports mask */ + u16 enabled_ports; + unsigned int imp_port; +- unsigned int cpu_port; + + /* connect specific data */ + u8 current_page; diff --git a/target/linux/generic/backport-5.10/744-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch b/target/linux/generic/backport-5.10/744-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch new file mode 100644 index 0000000000..ab4fdf8509 --- /dev/null +++ b/target/linux/generic/backport-5.10/744-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch @@ -0,0 +1,138 @@ +From bea7907837c57a0aaac009931eb14efb056dafab Mon Sep 17 00:00:00 2001 +From: Vladimir Oltean +Date: Thu, 29 Jul 2021 17:56:00 +0300 +Subject: [PATCH] net: dsa: don't set skb->offload_fwd_mark when not offloading + the bridge + +DSA has gained the recent ability to deal gracefully with upper +interfaces it cannot offload, such as the bridge, bonding or team +drivers. When such uppers exist, the ports are still in standalone mode +as far as the hardware is concerned. + +But when we deliver packets to the software bridge in order for that to +do the forwarding, there is an unpleasant surprise in that the bridge +will refuse to forward them. This is because we unconditionally set +skb->offload_fwd_mark = true, meaning that the bridge thinks the frames +were already forwarded in hardware by us. + +Since dp->bridge_dev is populated only when there is hardware offload +for it, but not in the software fallback case, let's introduce a new +helper that can be called from the tagger data path which sets the +skb->offload_fwd_mark accordingly to zero when there is no hardware +offload for bridging. This lets the bridge forward packets back to other +interfaces of our switch, if needed. + +Signed-off-by: Vladimir Oltean +Reviewed-by: Tobias Waldekranz +Signed-off-by: David S. Miller +--- + net/dsa/dsa_priv.h | 14 ++++++++++++++ + net/dsa/tag_brcm.c | 4 ++-- + net/dsa/tag_dsa.c | 15 +++++++++++---- + net/dsa/tag_ksz.c | 2 +- + net/dsa/tag_lan9303.c | 3 ++- + net/dsa/tag_mtk.c | 2 +- + net/dsa/tag_ocelot.c | 2 +- + net/dsa/tag_rtl4_a.c | 2 +- + net/dsa/tag_sja1105.c | 20 ++++++++++++++------ + 9 files changed, 47 insertions(+), 17 deletions(-) + +--- a/net/dsa/dsa_priv.h ++++ b/net/dsa/dsa_priv.h +@@ -266,6 +266,20 @@ static inline struct sk_buff *dsa_untag_ + return skb; + } + ++/* If the ingress port offloads the bridge, we mark the frame as autonomously ++ * forwarded by hardware, so the software bridge doesn't forward in twice, back ++ * to us, because we already did. However, if we're in fallback mode and we do ++ * software bridging, we are not offloading it, therefore the dp->bridge_dev ++ * pointer is not populated, and flooding needs to be done by software (we are ++ * effectively operating in standalone ports mode). ++ */ ++static inline void dsa_default_offload_fwd_mark(struct sk_buff *skb) ++{ ++ struct dsa_port *dp = dsa_slave_to_port(skb->dev); ++ ++ skb->offload_fwd_mark = !!(dp->bridge_dev); ++} ++ + /* switch.c */ + int dsa_switch_register_notifier(struct dsa_switch *ds); + void dsa_switch_unregister_notifier(struct dsa_switch *ds); +--- a/net/dsa/tag_brcm.c ++++ b/net/dsa/tag_brcm.c +@@ -166,7 +166,7 @@ static struct sk_buff *brcm_tag_rcv_ll(s + /* Remove Broadcom tag and update checksum */ + skb_pull_rcsum(skb, BRCM_TAG_LEN); + +- skb->offload_fwd_mark = 1; ++ dsa_default_offload_fwd_mark(skb); + + return skb; + } +@@ -270,7 +270,7 @@ static struct sk_buff *brcm_leg_tag_rcv( + /* Remove Broadcom tag and update checksum */ + skb_pull_rcsum(skb, BRCM_LEG_TAG_LEN); + +- skb->offload_fwd_mark = 1; ++ dsa_default_offload_fwd_mark(skb); + + /* Move the Ethernet DA and SA */ + memmove(skb->data - ETH_HLEN, +--- a/net/dsa/tag_ksz.c ++++ b/net/dsa/tag_ksz.c +@@ -24,7 +24,7 @@ static struct sk_buff *ksz_common_rcv(st + + pskb_trim_rcsum(skb, skb->len - len); + +- skb->offload_fwd_mark = true; ++ dsa_default_offload_fwd_mark(skb); + + return skb; + } +--- a/net/dsa/tag_lan9303.c ++++ b/net/dsa/tag_lan9303.c +@@ -115,7 +115,8 @@ static struct sk_buff *lan9303_rcv(struc + skb_pull_rcsum(skb, 2 + 2); + memmove(skb->data - ETH_HLEN, skb->data - (ETH_HLEN + LAN9303_TAG_LEN), + 2 * ETH_ALEN); +- skb->offload_fwd_mark = !(lan9303_tag1 & LAN9303_TAG_RX_TRAPPED_TO_CPU); ++ if (!(lan9303_tag1 & LAN9303_TAG_RX_TRAPPED_TO_CPU)) ++ dsa_default_offload_fwd_mark(skb); + + return skb; + } +--- a/net/dsa/tag_mtk.c ++++ b/net/dsa/tag_mtk.c +@@ -104,7 +104,7 @@ static struct sk_buff *mtk_tag_rcv(struc + + /* Only unicast or broadcast frames are offloaded */ + if (likely(!is_multicast_skb)) +- skb->offload_fwd_mark = 1; ++ dsa_default_offload_fwd_mark(skb); + + return skb; + } +--- a/net/dsa/tag_ocelot.c ++++ b/net/dsa/tag_ocelot.c +@@ -225,7 +225,7 @@ static struct sk_buff *ocelot_rcv(struct + */ + return NULL; + +- skb->offload_fwd_mark = 1; ++ dsa_default_offload_fwd_mark(skb); + skb->priority = qos_class; + + /* Ocelot switches copy frames unmodified to the CPU. However, it is +--- a/net/dsa/tag_rtl4_a.c ++++ b/net/dsa/tag_rtl4_a.c +@@ -115,7 +115,7 @@ static struct sk_buff *rtl4a_tag_rcv(str + skb->data - ETH_HLEN - RTL4_A_HDR_LEN, + 2 * ETH_ALEN); + +- skb->offload_fwd_mark = 1; ++ dsa_default_offload_fwd_mark(skb); + + return skb; + } diff --git a/target/linux/generic/backport-5.10/745-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch b/target/linux/generic/backport-5.10/745-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch new file mode 100644 index 0000000000..c82bf913a0 --- /dev/null +++ b/target/linux/generic/backport-5.10/745-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch @@ -0,0 +1,65 @@ +From b4df02b562f4aa14ff6811f30e1b4d2159585c59 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 19 Sep 2021 18:28:15 +0200 +Subject: net: phy: at803x: add support for qca 8327 A variant internal phy + +For qca8327 internal phy there are 2 different switch variant with 2 +different phy id. Add this missing variant so the internal phy can be +correctly identified and fixed. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 25 ++++++++++++++++++++----- + 1 file changed, 20 insertions(+), 5 deletions(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -148,7 +148,8 @@ + #define AT803X_PAGE_FIBER 0 + #define AT803X_PAGE_COPPER 1 + +-#define QCA8327_PHY_ID 0x004dd034 ++#define QCA8327_A_PHY_ID 0x004dd033 ++#define QCA8327_B_PHY_ID 0x004dd034 + #define QCA8337_PHY_ID 0x004dd036 + #define QCA8K_PHY_ID_MASK 0xffffffff + +@@ -1329,10 +1330,23 @@ static struct phy_driver at803x_driver[] + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, + }, { +- /* QCA8327 */ +- .phy_id = QCA8327_PHY_ID, ++ /* QCA8327-A from switch QCA8327-AL1A */ ++ .phy_id = QCA8327_A_PHY_ID, + .phy_id_mask = QCA8K_PHY_ID_MASK, +- .name = "QCA PHY 8327", ++ .name = "QCA PHY 8327-A", ++ /* PHY_GBIT_FEATURES */ ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, ++}, { ++ /* QCA8327-B from switch QCA8327-BL1A */ ++ .phy_id = QCA8327_B_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "QCA PHY 8327-B", + /* PHY_GBIT_FEATURES */ + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, +@@ -1352,7 +1366,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) }, +- { PHY_ID_MATCH_EXACT(QCA8327_PHY_ID) }, ++ { PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) }, ++ { PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) }, + { } + }; + diff --git a/target/linux/generic/backport-5.10/745-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch b/target/linux/generic/backport-5.10/745-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch new file mode 100644 index 0000000000..be24fd5cf7 --- /dev/null +++ b/target/linux/generic/backport-5.10/745-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch @@ -0,0 +1,45 @@ +From 15b9df4ece17d084f14eb0ca1cf05f2ad497e425 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 19 Sep 2021 18:28:16 +0200 +Subject: net: phy: at803x: add resume/suspend function to qca83xx phy + +Add resume/suspend function to qca83xx internal phy. +We can't use the at803x generic function as the documentation lacks of +any support for WoL regs. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -1329,6 +1329,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, + }, { + /* QCA8327-A from switch QCA8327-AL1A */ + .phy_id = QCA8327_A_PHY_ID, +@@ -1342,6 +1344,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, + }, { + /* QCA8327-B from switch QCA8327-BL1A */ + .phy_id = QCA8327_B_PHY_ID, +@@ -1355,6 +1359,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, + }, }; + + module_phy_driver(at803x_driver); diff --git a/target/linux/generic/backport-5.10/745-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch b/target/linux/generic/backport-5.10/745-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch new file mode 100644 index 0000000000..23f574c76f --- /dev/null +++ b/target/linux/generic/backport-5.10/745-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch @@ -0,0 +1,95 @@ +From d44fd8604a4ab92119adb35f05fd87612af722b5 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 19 Sep 2021 18:28:17 +0200 +Subject: net: phy: at803x: fix spacing and improve name for 83xx phy + +Fix spacing and improve name for 83xx phy following other phy in the +same driver. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 60 ++++++++++++++++++++++++------------------------ + 1 file changed, 30 insertions(+), 30 deletions(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -1318,47 +1318,47 @@ static struct phy_driver at803x_driver[] + .config_aneg = at803x_config_aneg, + }, { + /* QCA8337 */ +- .phy_id = QCA8337_PHY_ID, +- .phy_id_mask = QCA8K_PHY_ID_MASK, +- .name = "QCA PHY 8337", ++ .phy_id = QCA8337_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "Qualcomm Atheros 8337 internal PHY", + /* PHY_GBIT_FEATURES */ +- .probe = at803x_probe, +- .flags = PHY_IS_INTERNAL, +- .config_init = qca83xx_config_init, +- .soft_reset = genphy_soft_reset, +- .get_sset_count = at803x_get_sset_count, +- .get_strings = at803x_get_strings, +- .get_stats = at803x_get_stats, ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, + .suspend = genphy_suspend, + .resume = genphy_resume, + }, { + /* QCA8327-A from switch QCA8327-AL1A */ +- .phy_id = QCA8327_A_PHY_ID, +- .phy_id_mask = QCA8K_PHY_ID_MASK, +- .name = "QCA PHY 8327-A", ++ .phy_id = QCA8327_A_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "Qualcomm Atheros 8327-A internal PHY", + /* PHY_GBIT_FEATURES */ +- .probe = at803x_probe, +- .flags = PHY_IS_INTERNAL, +- .config_init = qca83xx_config_init, +- .soft_reset = genphy_soft_reset, +- .get_sset_count = at803x_get_sset_count, +- .get_strings = at803x_get_strings, +- .get_stats = at803x_get_stats, ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, + .suspend = genphy_suspend, + .resume = genphy_resume, + }, { + /* QCA8327-B from switch QCA8327-BL1A */ +- .phy_id = QCA8327_B_PHY_ID, +- .phy_id_mask = QCA8K_PHY_ID_MASK, +- .name = "QCA PHY 8327-B", ++ .phy_id = QCA8327_B_PHY_ID, ++ .phy_id_mask = QCA8K_PHY_ID_MASK, ++ .name = "Qualcomm Atheros 8327-B internal PHY", + /* PHY_GBIT_FEATURES */ +- .probe = at803x_probe, +- .flags = PHY_IS_INTERNAL, +- .config_init = qca83xx_config_init, +- .soft_reset = genphy_soft_reset, +- .get_sset_count = at803x_get_sset_count, +- .get_strings = at803x_get_strings, +- .get_stats = at803x_get_stats, ++ .probe = at803x_probe, ++ .flags = PHY_IS_INTERNAL, ++ .config_init = qca83xx_config_init, ++ .soft_reset = genphy_soft_reset, ++ .get_sset_count = at803x_get_sset_count, ++ .get_strings = at803x_get_strings, ++ .get_stats = at803x_get_stats, + .suspend = genphy_suspend, + .resume = genphy_resume, + }, }; diff --git a/target/linux/generic/backport-5.10/746-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch b/target/linux/generic/backport-5.10/746-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch new file mode 100644 index 0000000000..5dfe27dd24 --- /dev/null +++ b/target/linux/generic/backport-5.10/746-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch @@ -0,0 +1,131 @@ +From ba3c01ee02ed0d821c9f241f179bbc9457542b8f Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 10 Oct 2021 00:46:15 +0200 +Subject: net: phy: at803x: fix resume for QCA8327 phy + +From Documentation phy resume triggers phy reset and restart +auto-negotiation. Add a dedicated function to wait reset to finish as +it was notice a regression where port sometime are not reliable after a +suspend/resume session. The reset wait logic is copied from phy_poll_reset. +Add dedicated suspend function to use genphy_suspend only with QCA8337 +phy and set only additional debug settings for QCA8327. With more test +it was reported that QCA8327 doesn't proprely support this mode and +using this cause the unreliability of the switch ports, especially the +malfunction of the port0. + +Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy") +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 69 +++++++++++++++++++++++++++++++++++++++++++----- + 1 file changed, 63 insertions(+), 6 deletions(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -92,9 +92,14 @@ + #define AT803X_DEBUG_REG_5 0x05 + #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) + ++#define AT803X_DEBUG_REG_HIB_CTRL 0x0b ++#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10) ++#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13) ++ + #define AT803X_DEBUG_REG_3C 0x3C + + #define AT803X_DEBUG_REG_3D 0x3D ++#define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6) + + #define AT803X_DEBUG_REG_1F 0x1F + #define AT803X_DEBUG_PLL_ON BIT(2) +@@ -1220,6 +1225,58 @@ static int qca83xx_config_init(struct ph + return 0; + } + ++static int qca83xx_resume(struct phy_device *phydev) ++{ ++ int ret, val; ++ ++ /* Skip reset if not suspended */ ++ if (!phydev->suspended) ++ return 0; ++ ++ /* Reinit the port, reset values set by suspend */ ++ qca83xx_config_init(phydev); ++ ++ /* Reset the port on port resume */ ++ phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE); ++ ++ /* On resume from suspend the switch execute a reset and ++ * restart auto-negotiation. Wait for reset to complete. ++ */ ++ ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET), ++ 50000, 600000, true); ++ if (ret) ++ return ret; ++ ++ msleep(1); ++ ++ return 0; ++} ++ ++static int qca83xx_suspend(struct phy_device *phydev) ++{ ++ u16 mask = 0; ++ ++ /* Only QCA8337 support actual suspend. ++ * QCA8327 cause port unreliability when phy suspend ++ * is set. ++ */ ++ if (phydev->drv->phy_id == QCA8337_PHY_ID) { ++ genphy_suspend(phydev); ++ } else { ++ mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX); ++ phy_modify(phydev, MII_BMCR, mask, 0); ++ } ++ ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_3D, ++ AT803X_DEBUG_GATE_CLK_IN1000, 0); ++ ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, ++ AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE | ++ AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0); ++ ++ return 0; ++} ++ + static struct phy_driver at803x_driver[] = { + { + /* Qualcomm Atheros AR8035 */ +@@ -1329,8 +1386,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, +- .suspend = genphy_suspend, +- .resume = genphy_resume, ++ .suspend = qca83xx_suspend, ++ .resume = qca83xx_resume, + }, { + /* QCA8327-A from switch QCA8327-AL1A */ + .phy_id = QCA8327_A_PHY_ID, +@@ -1344,8 +1401,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, +- .suspend = genphy_suspend, +- .resume = genphy_resume, ++ .suspend = qca83xx_suspend, ++ .resume = qca83xx_resume, + }, { + /* QCA8327-B from switch QCA8327-BL1A */ + .phy_id = QCA8327_B_PHY_ID, +@@ -1359,8 +1416,8 @@ static struct phy_driver at803x_driver[] + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, +- .suspend = genphy_suspend, +- .resume = genphy_resume, ++ .suspend = qca83xx_suspend, ++ .resume = qca83xx_resume, + }, }; + + module_phy_driver(at803x_driver); diff --git a/target/linux/generic/backport-5.10/746-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch b/target/linux/generic/backport-5.10/746-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch new file mode 100644 index 0000000000..aeb43e2f67 --- /dev/null +++ b/target/linux/generic/backport-5.10/746-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch @@ -0,0 +1,91 @@ +From 1ca8311949aec5c9447645731ef1c6bc5bd71350 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 10 Oct 2021 00:46:16 +0200 +Subject: net: phy: at803x: add DAC amplitude fix for 8327 phy + +QCA8327 internal phy require DAC amplitude adjustement set to +6% with +100m speed. Also add additional define to report a change of the same +reg in QCA8337. (different scope it does set 1000m voltage) +Add link_change_notify function to set the proper amplitude adjustement +on PHY_RUNNING state and disable on any other state. + +Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy") +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 33 +++++++++++++++++++++++++++++++++ + 1 file changed, 33 insertions(+) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -87,6 +87,8 @@ + #define AT803X_PSSR_MR_AN_COMPLETE 0x0200 + + #define AT803X_DEBUG_REG_0 0x00 ++#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) ++#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) + #define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) + + #define AT803X_DEBUG_REG_5 0x05 +@@ -1222,9 +1224,37 @@ static int qca83xx_config_init(struct ph + break; + } + ++ /* QCA8327 require DAC amplitude adjustment for 100m set to +6%. ++ * Disable on init and enable only with 100m speed following ++ * qca original source code. ++ */ ++ if (phydev->drv->phy_id == QCA8327_A_PHY_ID || ++ phydev->drv->phy_id == QCA8327_B_PHY_ID) ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ QCA8327_DEBUG_MANU_CTRL_EN, 0); ++ + return 0; + } + ++static void qca83xx_link_change_notify(struct phy_device *phydev) ++{ ++ /* QCA8337 doesn't require DAC Amplitude adjustement */ ++ if (phydev->drv->phy_id == QCA8337_PHY_ID) ++ return; ++ ++ /* Set DAC Amplitude adjustment to +6% for 100m on link running */ ++ if (phydev->state == PHY_RUNNING) { ++ if (phydev->speed == SPEED_100) ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ QCA8327_DEBUG_MANU_CTRL_EN, ++ QCA8327_DEBUG_MANU_CTRL_EN); ++ } else { ++ /* Reset DAC Amplitude adjustment */ ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ QCA8327_DEBUG_MANU_CTRL_EN, 0); ++ } ++} ++ + static int qca83xx_resume(struct phy_device *phydev) + { + int ret, val; +@@ -1379,6 +1409,7 @@ static struct phy_driver at803x_driver[] + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8337 internal PHY", + /* PHY_GBIT_FEATURES */ ++ .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, +@@ -1394,6 +1425,7 @@ static struct phy_driver at803x_driver[] + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8327-A internal PHY", + /* PHY_GBIT_FEATURES */ ++ .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, +@@ -1409,6 +1441,7 @@ static struct phy_driver at803x_driver[] + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8327-B internal PHY", + /* PHY_GBIT_FEATURES */ ++ .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, diff --git a/target/linux/generic/backport-5.10/746-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch b/target/linux/generic/backport-5.10/746-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch new file mode 100644 index 0000000000..2352fa0e44 --- /dev/null +++ b/target/linux/generic/backport-5.10/746-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch @@ -0,0 +1,27 @@ +From 9d1c29b4028557a496be9c5eb2b4b86063700636 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 10 Oct 2021 00:46:17 +0200 +Subject: net: phy: at803x: enable prefer master for 83xx internal phy + +From original QCA source code the port was set to prefer master as port +type in 1000BASE-T mode. Apply the same settings also here. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -1233,6 +1233,9 @@ static int qca83xx_config_init(struct ph + at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, + QCA8327_DEBUG_MANU_CTRL_EN, 0); + ++ /* Following original QCA sourcecode set port to prefer master */ ++ phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER); ++ + return 0; + } + diff --git a/target/linux/generic/backport-5.10/746-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch b/target/linux/generic/backport-5.10/746-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch new file mode 100644 index 0000000000..9c28a893f1 --- /dev/null +++ b/target/linux/generic/backport-5.10/746-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch @@ -0,0 +1,127 @@ +From 67999555ff42e91de7654488d9a7735bd9e84555 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 10 Oct 2021 00:46:18 +0200 +Subject: net: phy: at803x: better describe debug regs + +Give a name to known debug regs from Documentation instead of using +unknown hex values. + +Signed-off-by: Ansuel Smith +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/phy/at803x.c | 30 +++++++++++++++--------------- + 1 file changed, 15 insertions(+), 15 deletions(-) + +--- a/drivers/net/phy/at803x.c ++++ b/drivers/net/phy/at803x.c +@@ -86,12 +86,12 @@ + #define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/ + #define AT803X_PSSR_MR_AN_COMPLETE 0x0200 + +-#define AT803X_DEBUG_REG_0 0x00 ++#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00 + #define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) + #define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) + #define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) + +-#define AT803X_DEBUG_REG_5 0x05 ++#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05 + #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) + + #define AT803X_DEBUG_REG_HIB_CTRL 0x0b +@@ -100,7 +100,7 @@ + + #define AT803X_DEBUG_REG_3C 0x3C + +-#define AT803X_DEBUG_REG_3D 0x3D ++#define AT803X_DEBUG_REG_GREEN 0x3D + #define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6) + + #define AT803X_DEBUG_REG_1F 0x1F +@@ -274,25 +274,25 @@ static int at803x_read_page(struct phy_d + + static int at803x_enable_rx_delay(struct phy_device *phydev) + { +- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, ++ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0, + AT803X_DEBUG_RX_CLK_DLY_EN); + } + + static int at803x_enable_tx_delay(struct phy_device *phydev) + { +- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0, ++ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0, + AT803X_DEBUG_TX_CLK_DLY_EN); + } + + static int at803x_disable_rx_delay(struct phy_device *phydev) + { +- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + AT803X_DEBUG_RX_CLK_DLY_EN, 0); + } + + static int at803x_disable_tx_delay(struct phy_device *phydev) + { +- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, ++ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, + AT803X_DEBUG_TX_CLK_DLY_EN, 0); + } + +@@ -1208,9 +1208,9 @@ static int qca83xx_config_init(struct ph + switch (switch_revision) { + case 1: + /* For 100M waveform */ +- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_0, 0x02ea); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea); + /* Turn on Gigabit clock */ +- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x68a0); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0); + break; + + case 2: +@@ -1218,8 +1218,8 @@ static int qca83xx_config_init(struct ph + fallthrough; + case 4: + phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f); +- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x6860); +- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_5, 0x2c46); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860); ++ at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46); + at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000); + break; + } +@@ -1230,7 +1230,7 @@ static int qca83xx_config_init(struct ph + */ + if (phydev->drv->phy_id == QCA8327_A_PHY_ID || + phydev->drv->phy_id == QCA8327_B_PHY_ID) +- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, 0); + + /* Following original QCA sourcecode set port to prefer master */ +@@ -1248,12 +1248,12 @@ static void qca83xx_link_change_notify(s + /* Set DAC Amplitude adjustment to +6% for 100m on link running */ + if (phydev->state == PHY_RUNNING) { + if (phydev->speed == SPEED_100) +- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, + QCA8327_DEBUG_MANU_CTRL_EN); + } else { + /* Reset DAC Amplitude adjustment */ +- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, 0); + } + } +@@ -1300,7 +1300,7 @@ static int qca83xx_suspend(struct phy_de + phy_modify(phydev, MII_BMCR, mask, 0); + } + +- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_3D, ++ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN, + AT803X_DEBUG_GATE_CLK_IN1000, 0); + + at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, diff --git a/target/linux/generic/backport-5.10/747-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch b/target/linux/generic/backport-5.10/747-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch new file mode 100644 index 0000000000..c8d424de38 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch @@ -0,0 +1,80 @@ +From d8b6f5bae6d3b648a67b6958cb98e4e97256d652 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:06 +0200 +Subject: dsa: qca8k: add mac_power_sel support + +Add missing mac power sel support needed for ipq8064/5 SoC that require +1.8v for the internal regulator port instead of the default 1.5v. +If other device needs this, consider adding a dedicated binding to +support this. + +Signed-off-by: Ansuel Smith +Reviewed-by: Vladimir Oltean +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 31 +++++++++++++++++++++++++++++++ + drivers/net/dsa/qca8k.h | 5 +++++ + 2 files changed, 36 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -951,6 +951,33 @@ qca8k_setup_of_rgmii_delay(struct qca8k_ + } + + static int ++qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv) ++{ ++ u32 mask = 0; ++ int ret = 0; ++ ++ /* SoC specific settings for ipq8064. ++ * If more device require this consider adding ++ * a dedicated binding. ++ */ ++ if (of_machine_is_compatible("qcom,ipq8064")) ++ mask |= QCA8K_MAC_PWR_RGMII0_1_8V; ++ ++ /* SoC specific settings for ipq8065 */ ++ if (of_machine_is_compatible("qcom,ipq8065")) ++ mask |= QCA8K_MAC_PWR_RGMII1_1_8V; ++ ++ if (mask) { ++ ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL, ++ QCA8K_MAC_PWR_RGMII0_1_8V | ++ QCA8K_MAC_PWR_RGMII1_1_8V, ++ mask); ++ } ++ ++ return ret; ++} ++ ++static int + qca8k_setup(struct dsa_switch *ds) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +@@ -979,6 +1006,10 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + ++ ret = qca8k_setup_mac_pwr_sel(priv); ++ if (ret) ++ return ret; ++ + /* Enable CPU Port */ + ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, + QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -100,6 +100,11 @@ + #define QCA8K_SGMII_MODE_CTRL_PHY (1 << 22) + #define QCA8K_SGMII_MODE_CTRL_MAC (2 << 22) + ++/* MAC_PWR_SEL registers */ ++#define QCA8K_REG_MAC_PWR_SEL 0x0e4 ++#define QCA8K_MAC_PWR_RGMII1_1_8V BIT(18) ++#define QCA8K_MAC_PWR_RGMII0_1_8V BIT(19) ++ + /* EEE control registers */ + #define QCA8K_REG_EEE_CTRL 0x100 + #define QCA8K_REG_EEE_CTRL_LPI_EN(_i) ((_i + 1) * 2) diff --git a/target/linux/generic/backport-5.10/747-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch b/target/linux/generic/backport-5.10/747-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch new file mode 100644 index 0000000000..bd768ec27d --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch @@ -0,0 +1,30 @@ +From fdbf35df9c091db9c46e57e9938e3f7a4f603a7c Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:07 +0200 +Subject: dt-bindings: net: dsa: qca8k: Add SGMII clock phase properties + +Add names and descriptions of additional PORT0_PAD_CTRL properties. +qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock +phase to failling edge. + +Co-developed-by: Matthew Hagan +Signed-off-by: Matthew Hagan +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -37,6 +37,10 @@ A CPU port node has the following option + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. ++- qca,sgmii-rxclk-falling-edge: Set the receive clock phase to falling edge. ++ Mostly used in qca8327 with CPU port 0 set to ++ sgmii. ++- qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. + + For QCA8K the 'fixed-link' sub-node supports only the following properties: + diff --git a/target/linux/generic/backport-5.10/747-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch b/target/linux/generic/backport-5.10/747-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch new file mode 100644 index 0000000000..e464452d82 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch @@ -0,0 +1,127 @@ +From 6c43809bf1bee76c434e365a26546a92a5fbec14 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:08 +0200 +Subject: net: dsa: qca8k: add support for sgmii falling edge + +Add support for this in the qca8k driver. Also add support for SGMII +rx/tx clock falling edge. This is only present for pad0, pad5 and +pad6 have these bit reserved from Documentation. Add a comment that this +is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and +setting falling in port0 applies to both configuration with sgmii used +for port0 or port6. + +Co-developed-by: Matthew Hagan +Signed-off-by: Matthew Hagan +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 63 +++++++++++++++++++++++++++++++++++++++++++++++++ + drivers/net/dsa/qca8k.h | 4 ++++ + 2 files changed, 67 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -978,6 +978,42 @@ qca8k_setup_mac_pwr_sel(struct qca8k_pri + } + + static int ++qca8k_parse_port_config(struct qca8k_priv *priv) ++{ ++ struct device_node *port_dn; ++ phy_interface_t mode; ++ struct dsa_port *dp; ++ int port, ret; ++ ++ /* We have 2 CPU port. Check them */ ++ for (port = 0; port < QCA8K_NUM_PORTS; port++) { ++ /* Skip every other port */ ++ if (port != 0 && port != 6) ++ continue; ++ ++ dp = dsa_to_port(priv->ds, port); ++ port_dn = dp->dn; ++ ++ if (!of_device_is_available(port_dn)) ++ continue; ++ ++ ret = of_get_phy_mode(port_dn, &mode); ++ if (ret) ++ continue; ++ ++ if (mode == PHY_INTERFACE_MODE_SGMII) { ++ if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) ++ priv->sgmii_tx_clk_falling_edge = true; ++ ++ if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) ++ priv->sgmii_rx_clk_falling_edge = true; ++ } ++ } ++ ++ return 0; ++} ++ ++static int + qca8k_setup(struct dsa_switch *ds) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +@@ -990,6 +1026,11 @@ qca8k_setup(struct dsa_switch *ds) + return -EINVAL; + } + ++ /* Parse CPU port config to be later used in phy_link mac_config */ ++ ret = qca8k_parse_port_config(priv); ++ if (ret) ++ return ret; ++ + mutex_init(&priv->reg_mutex); + + /* Start by setting up the register mapping */ +@@ -1274,6 +1315,28 @@ qca8k_phylink_mac_config(struct dsa_swit + } + + qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val); ++ ++ /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and ++ * falling edge is set writing in the PORT0 PAD reg ++ */ ++ if (priv->switch_id == QCA8K_ID_QCA8327 || ++ priv->switch_id == QCA8K_ID_QCA8337) ++ reg = QCA8K_REG_PORT0_PAD_CTRL; ++ ++ val = 0; ++ ++ /* SGMII Clock phase configuration */ ++ if (priv->sgmii_rx_clk_falling_edge) ++ val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE; ++ ++ if (priv->sgmii_tx_clk_falling_edge) ++ val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE; ++ ++ if (val) ++ ret = qca8k_rmw(priv, reg, ++ QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE | ++ QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, ++ val); + break; + default: + dev_err(ds->dev, "xMII mode %s not supported for port %d\n", +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -35,6 +35,8 @@ + #define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8) + #define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8) + #define QCA8K_REG_PORT0_PAD_CTRL 0x004 ++#define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19) ++#define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18) + #define QCA8K_REG_PORT5_PAD_CTRL 0x008 + #define QCA8K_REG_PORT6_PAD_CTRL 0x00c + #define QCA8K_PORT_PAD_RGMII_EN BIT(26) +@@ -260,6 +262,8 @@ struct qca8k_priv { + u8 switch_revision; + u8 rgmii_tx_delay; + u8 rgmii_rx_delay; ++ bool sgmii_rx_clk_falling_edge; ++ bool sgmii_tx_clk_falling_edge; + bool legacy_phy_port_mapping; + struct regmap *regmap; + struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/747-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch b/target/linux/generic/backport-5.10/747-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch new file mode 100644 index 0000000000..606ac0af3d --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch @@ -0,0 +1,29 @@ +From 731d613338ec6de482053ffa3f71be2325b0f8eb Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:09 +0200 +Subject: dt-bindings: net: dsa: qca8k: Document support for CPU port 6 + +The switch now support CPU port to be set 6 instead of be hardcoded to +0. Document support for it and describe logic selection. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -29,7 +29,11 @@ the mdio MASTER is used as communication + Don't use mixed external and internal mdio-bus configurations, as this is + not supported by the hardware. + +-The CPU port of this switch is always port 0. ++This switch support 2 CPU port. Normally and advised configuration is with ++CPU port set to port 0. It is also possible to set the CPU port to port 6 ++if the device requires it. The driver will configure the switch to the defined ++port. With both CPU port declared the first CPU port is selected as primary ++and the secondary CPU ignored. + + A CPU port node has the following optional node: + diff --git a/target/linux/generic/backport-5.10/747-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch b/target/linux/generic/backport-5.10/747-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch new file mode 100644 index 0000000000..320db8fa9f --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch @@ -0,0 +1,153 @@ +From 3fcf734aa482487df83cf8f18608438fcf59127f Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:10 +0200 +Subject: net: dsa: qca8k: add support for cpu port 6 + +Currently CPU port is always hardcoded to port 0. This switch have 2 CPU +ports. The original intention of this driver seems to be use the +mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration +where device have connected only the CPU port 6. To skip the +introduction of a new binding, rework the driver to address the +secondary CPU port as primary and drop any reference of hardcoded port. +With configuration of mac06 exchange, just skip the definition of port0 +and define the CPU port as a secondary. The driver will autoconfigure +the switch to use that as the primary CPU port. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 51 ++++++++++++++++++++++++++++++++++--------------- + drivers/net/dsa/qca8k.h | 2 -- + 2 files changed, 36 insertions(+), 17 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -977,6 +977,22 @@ qca8k_setup_mac_pwr_sel(struct qca8k_pri + return ret; + } + ++static int qca8k_find_cpu_port(struct dsa_switch *ds) ++{ ++ struct qca8k_priv *priv = ds->priv; ++ ++ /* Find the connected cpu port. Valid port are 0 or 6 */ ++ if (dsa_is_cpu_port(ds, 0)) ++ return 0; ++ ++ dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6"); ++ ++ if (dsa_is_cpu_port(ds, 6)) ++ return 6; ++ ++ return -EINVAL; ++} ++ + static int + qca8k_parse_port_config(struct qca8k_priv *priv) + { +@@ -1017,13 +1033,13 @@ static int + qca8k_setup(struct dsa_switch *ds) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +- int ret, i; ++ int cpu_port, ret, i; + u32 mask; + +- /* Make sure that port 0 is the cpu port */ +- if (!dsa_is_cpu_port(ds, 0)) { +- dev_err(priv->dev, "port 0 is not the CPU port"); +- return -EINVAL; ++ cpu_port = qca8k_find_cpu_port(ds); ++ if (cpu_port < 0) { ++ dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6"); ++ return cpu_port; + } + + /* Parse CPU port config to be later used in phy_link mac_config */ +@@ -1065,7 +1081,7 @@ qca8k_setup(struct dsa_switch *ds) + dev_warn(priv->dev, "mib init failed"); + + /* Enable QCA header mode on the cpu port */ +- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), ++ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(cpu_port), + QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | + QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); + if (ret) { +@@ -1087,10 +1103,10 @@ qca8k_setup(struct dsa_switch *ds) + + /* Forward all unknown frames to CPU port for Linux processing */ + ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | +- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); ++ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | ++ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | ++ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | ++ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); + if (ret) + return ret; + +@@ -1098,7 +1114,7 @@ qca8k_setup(struct dsa_switch *ds) + for (i = 0; i < QCA8K_NUM_PORTS; i++) { + /* CPU port gets connected to all user ports of the switch */ + if (dsa_is_cpu_port(ds, i)) { +- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port), + QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); + if (ret) + return ret; +@@ -1110,7 +1126,7 @@ qca8k_setup(struct dsa_switch *ds) + + ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), + QCA8K_PORT_LOOKUP_MEMBER, +- BIT(QCA8K_CPU_PORT)); ++ BIT(cpu_port)); + if (ret) + return ret; + +@@ -1616,9 +1632,12 @@ static int + qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +- int port_mask = BIT(QCA8K_CPU_PORT); ++ int port_mask, cpu_port; + int i, ret; + ++ cpu_port = dsa_to_port(ds, port)->cpu_dp->index; ++ port_mask = BIT(cpu_port); ++ + for (i = 1; i < QCA8K_NUM_PORTS; i++) { + if (dsa_to_port(ds, i)->bridge_dev != br) + continue; +@@ -1645,7 +1664,9 @@ static void + qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) + { + struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; +- int i; ++ int cpu_port, i; ++ ++ cpu_port = dsa_to_port(ds, port)->cpu_dp->index; + + for (i = 1; i < QCA8K_NUM_PORTS; i++) { + if (dsa_to_port(ds, i)->bridge_dev != br) +@@ -1662,7 +1683,7 @@ qca8k_port_bridge_leave(struct dsa_switc + * this port + */ + qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), +- QCA8K_PORT_LOOKUP_MEMBER, BIT(QCA8K_CPU_PORT)); ++ QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port)); + } + + static int +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -24,8 +24,6 @@ + + #define QCA8K_NUM_FDB_RECORDS 2048 + +-#define QCA8K_CPU_PORT 0 +- + #define QCA8K_PORT_VID_DEF 1 + + /* Global control registers */ diff --git a/target/linux/generic/backport-5.10/747-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch b/target/linux/generic/backport-5.10/747-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch new file mode 100644 index 0000000000..de201764f9 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch @@ -0,0 +1,295 @@ +From 5654ec78dd7e64b1e04777b24007344329e6a63b Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:11 +0200 +Subject: net: dsa: qca8k: rework rgmii delay logic and scan for cpu port 6 + +Future proof commit. This switch have 2 CPU ports and one valid +configuration is first CPU port set to sgmii and second CPU port set to +rgmii-id. The current implementation detects delay only for CPU port +zero set to rgmii and doesn't count any delay set in a secondary CPU +port. Drop the current delay scan function and move it to the sgmii +parser function to generalize and implicitly add support for secondary +CPU port set to rgmii-id. Introduce new logic where delay is enabled +also with internal delay binding declared and rgmii set as PHY mode. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 165 ++++++++++++++++++++++++------------------------ + drivers/net/dsa/qca8k.h | 10 ++- + 2 files changed, 89 insertions(+), 86 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -889,68 +889,6 @@ qca8k_setup_mdio_bus(struct qca8k_priv * + } + + static int +-qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv) +-{ +- struct device_node *port_dn; +- phy_interface_t mode; +- struct dsa_port *dp; +- u32 val; +- +- /* CPU port is already checked */ +- dp = dsa_to_port(priv->ds, 0); +- +- port_dn = dp->dn; +- +- /* Check if port 0 is set to the correct type */ +- of_get_phy_mode(port_dn, &mode); +- if (mode != PHY_INTERFACE_MODE_RGMII_ID && +- mode != PHY_INTERFACE_MODE_RGMII_RXID && +- mode != PHY_INTERFACE_MODE_RGMII_TXID) { +- return 0; +- } +- +- switch (mode) { +- case PHY_INTERFACE_MODE_RGMII_ID: +- case PHY_INTERFACE_MODE_RGMII_RXID: +- if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val)) +- val = 2; +- else +- /* Switch regs accept value in ns, convert ps to ns */ +- val = val / 1000; +- +- if (val > QCA8K_MAX_DELAY) { +- dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); +- val = 3; +- } +- +- priv->rgmii_rx_delay = val; +- /* Stop here if we need to check only for rx delay */ +- if (mode != PHY_INTERFACE_MODE_RGMII_ID) +- break; +- +- fallthrough; +- case PHY_INTERFACE_MODE_RGMII_TXID: +- if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val)) +- val = 1; +- else +- /* Switch regs accept value in ns, convert ps to ns */ +- val = val / 1000; +- +- if (val > QCA8K_MAX_DELAY) { +- dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); +- val = 3; +- } +- +- priv->rgmii_tx_delay = val; +- break; +- default: +- return 0; +- } +- +- return 0; +-} +- +-static int + qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv) + { + u32 mask = 0; +@@ -996,19 +934,21 @@ static int qca8k_find_cpu_port(struct ds + static int + qca8k_parse_port_config(struct qca8k_priv *priv) + { ++ int port, cpu_port_index = 0, ret; + struct device_node *port_dn; + phy_interface_t mode; + struct dsa_port *dp; +- int port, ret; ++ u32 delay; + + /* We have 2 CPU port. Check them */ +- for (port = 0; port < QCA8K_NUM_PORTS; port++) { ++ for (port = 0; port < QCA8K_NUM_PORTS && cpu_port_index < QCA8K_NUM_CPU_PORTS; port++) { + /* Skip every other port */ + if (port != 0 && port != 6) + continue; + + dp = dsa_to_port(priv->ds, port); + port_dn = dp->dn; ++ cpu_port_index++; + + if (!of_device_is_available(port_dn)) + continue; +@@ -1017,12 +957,54 @@ qca8k_parse_port_config(struct qca8k_pri + if (ret) + continue; + +- if (mode == PHY_INTERFACE_MODE_SGMII) { ++ switch (mode) { ++ case PHY_INTERFACE_MODE_RGMII: ++ case PHY_INTERFACE_MODE_RGMII_ID: ++ case PHY_INTERFACE_MODE_RGMII_TXID: ++ case PHY_INTERFACE_MODE_RGMII_RXID: ++ delay = 0; ++ ++ if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay)) ++ /* Switch regs accept value in ns, convert ps to ns */ ++ delay = delay / 1000; ++ else if (mode == PHY_INTERFACE_MODE_RGMII_ID || ++ mode == PHY_INTERFACE_MODE_RGMII_TXID) ++ delay = 1; ++ ++ if (delay > QCA8K_MAX_DELAY) { ++ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); ++ delay = 3; ++ } ++ ++ priv->rgmii_tx_delay[cpu_port_index] = delay; ++ ++ delay = 0; ++ ++ if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay)) ++ /* Switch regs accept value in ns, convert ps to ns */ ++ delay = delay / 1000; ++ else if (mode == PHY_INTERFACE_MODE_RGMII_ID || ++ mode == PHY_INTERFACE_MODE_RGMII_RXID) ++ delay = 2; ++ ++ if (delay > QCA8K_MAX_DELAY) { ++ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); ++ delay = 3; ++ } ++ ++ priv->rgmii_rx_delay[cpu_port_index] = delay; ++ ++ break; ++ case PHY_INTERFACE_MODE_SGMII: + if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) + priv->sgmii_tx_clk_falling_edge = true; + + if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) + priv->sgmii_rx_clk_falling_edge = true; ++ ++ break; ++ default: ++ continue; + } + } + +@@ -1059,10 +1041,6 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + +- ret = qca8k_setup_of_rgmii_delay(priv); +- if (ret) +- return ret; +- + ret = qca8k_setup_mac_pwr_sel(priv); + if (ret) + return ret; +@@ -1229,8 +1207,8 @@ qca8k_phylink_mac_config(struct dsa_swit + const struct phylink_link_state *state) + { + struct qca8k_priv *priv = ds->priv; +- u32 reg, val; +- int ret; ++ int cpu_port_index, ret; ++ u32 reg, val, delay; + + switch (port) { + case 0: /* 1st CPU port */ +@@ -1242,6 +1220,7 @@ qca8k_phylink_mac_config(struct dsa_swit + return; + + reg = QCA8K_REG_PORT0_PAD_CTRL; ++ cpu_port_index = QCA8K_CPU_PORT0; + break; + case 1: + case 2: +@@ -1260,6 +1239,7 @@ qca8k_phylink_mac_config(struct dsa_swit + return; + + reg = QCA8K_REG_PORT6_PAD_CTRL; ++ cpu_port_index = QCA8K_CPU_PORT6; + break; + default: + dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); +@@ -1274,23 +1254,40 @@ qca8k_phylink_mac_config(struct dsa_swit + + switch (state->interface) { + case PHY_INTERFACE_MODE_RGMII: +- /* RGMII mode means no delay so don't enable the delay */ +- qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); +- break; + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: +- /* RGMII_ID needs internal delay. This is enabled through +- * PORT5_PAD_CTRL for all ports, rather than individual port +- * registers ++ val = QCA8K_PORT_PAD_RGMII_EN; ++ ++ /* Delay can be declared in 3 different way. ++ * Mode to rgmii and internal-delay standard binding defined ++ * rgmii-id or rgmii-tx/rx phy mode set. ++ * The parse logic set a delay different than 0 only when one ++ * of the 3 different way is used. In all other case delay is ++ * not enabled. With ID or TX/RXID delay is enabled and set ++ * to the default and recommended value. ++ */ ++ if (priv->rgmii_tx_delay[cpu_port_index]) { ++ delay = priv->rgmii_tx_delay[cpu_port_index]; ++ ++ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | ++ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; ++ } ++ ++ if (priv->rgmii_rx_delay[cpu_port_index]) { ++ delay = priv->rgmii_rx_delay[cpu_port_index]; ++ ++ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; ++ } ++ ++ /* Set RGMII delay based on the selected values */ ++ qca8k_write(priv, reg, val); ++ ++ /* QCA8337 requires to set rgmii rx delay for all ports. ++ * This is enabled through PORT5_PAD_CTRL for all ports, ++ * rather than individual port registers. + */ +- qca8k_write(priv, reg, +- QCA8K_PORT_PAD_RGMII_EN | +- QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) | +- QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) | +- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | +- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); +- /* QCA8337 requires to set rgmii rx delay */ + if (priv->switch_id == QCA8K_ID_QCA8337) + qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, + QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -13,6 +13,7 @@ + #include + + #define QCA8K_NUM_PORTS 7 ++#define QCA8K_NUM_CPU_PORTS 2 + #define QCA8K_MAX_MTU 9000 + + #define PHY_ID_QCA8327 0x004dd034 +@@ -255,13 +256,18 @@ struct qca8k_match_data { + u8 id; + }; + ++enum { ++ QCA8K_CPU_PORT0, ++ QCA8K_CPU_PORT6, ++}; ++ + struct qca8k_priv { + u8 switch_id; + u8 switch_revision; +- u8 rgmii_tx_delay; +- u8 rgmii_rx_delay; + bool sgmii_rx_clk_falling_edge; + bool sgmii_tx_clk_falling_edge; ++ u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ ++ u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ + bool legacy_phy_port_mapping; + struct regmap *regmap; + struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/747-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch b/target/linux/generic/backport-5.10/747-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch new file mode 100644 index 0000000000..8abd264e79 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch @@ -0,0 +1,33 @@ +From 13ad5ccc093ff448b99ac7e138e91e78796adb48 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:12 +0200 +Subject: dt-bindings: net: dsa: qca8k: Document qca,sgmii-enable-pll + +Document qca,sgmii-enable-pll binding used in the CPU nodes to +enable SGMII PLL on MAC config. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 10 ++++++++++ + 1 file changed, 10 insertions(+) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -45,6 +45,16 @@ A CPU port node has the following option + Mostly used in qca8327 with CPU port 0 set to + sgmii. + - qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. ++- qca,sgmii-enable-pll : For SGMII CPU port, explicitly enable PLL, TX and RX ++ chain along with Signal Detection. ++ This should NOT be enabled for qca8327. If enabled with ++ qca8327 the sgmii port won't correctly init and an err ++ is printed. ++ This can be required for qca8337 switch with revision 2. ++ A warning is displayed when used with revision greater ++ 2. ++ With CPU port set to sgmii and qca8337 it is advised ++ to set this unless a communication problem is observed. + + For QCA8K the 'fixed-link' sub-node supports only the following properties: + diff --git a/target/linux/generic/backport-5.10/747-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch b/target/linux/generic/backport-5.10/747-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch new file mode 100644 index 0000000000..2b5a84a1b0 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch @@ -0,0 +1,65 @@ +From bbc4799e8bb6c397e3b3fec13de68e179f5db9ff Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:13 +0200 +Subject: net: dsa: qca8k: add explicit SGMII PLL enable + +Support enabling PLL on the SGMII CPU port. Some device require this +special configuration or no traffic is transmitted and the switch +doesn't work at all. A dedicated binding is added to the CPU node +port to apply the correct reg on mac config. +Fail to correctly configure sgmii with qca8327 switch and warn if pll is +used on qca8337 with a revision greater than 1. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 19 +++++++++++++++++-- + drivers/net/dsa/qca8k.h | 1 + + 2 files changed, 18 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1002,6 +1002,18 @@ qca8k_parse_port_config(struct qca8k_pri + if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) + priv->sgmii_rx_clk_falling_edge = true; + ++ if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) { ++ priv->sgmii_enable_pll = true; ++ ++ if (priv->switch_id == QCA8K_ID_QCA8327) { ++ dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling"); ++ priv->sgmii_enable_pll = false; ++ } ++ ++ if (priv->switch_revision < 2) ++ dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more."); ++ } ++ + break; + default: + continue; +@@ -1312,8 +1324,11 @@ qca8k_phylink_mac_config(struct dsa_swit + if (ret) + return; + +- val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | +- QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; ++ val |= QCA8K_SGMII_EN_SD; ++ ++ if (priv->sgmii_enable_pll) ++ val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | ++ QCA8K_SGMII_EN_TX; + + if (dsa_is_cpu_port(ds, port)) { + /* CPU port, we're talking to the CPU MAC, be a PHY */ +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -266,6 +266,7 @@ struct qca8k_priv { + u8 switch_revision; + bool sgmii_rx_clk_falling_edge; + bool sgmii_tx_clk_falling_edge; ++ bool sgmii_enable_pll; + u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ + u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ + bool legacy_phy_port_mapping; diff --git a/target/linux/generic/backport-5.10/747-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch b/target/linux/generic/backport-5.10/747-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch new file mode 100644 index 0000000000..38dc954e8c --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch @@ -0,0 +1,37 @@ +From 924087c5c3d41553700b0eb83ca2a53b91643dca Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:14 +0200 +Subject: dt-bindings: net: dsa: qca8k: Document qca,led-open-drain binding + +Document new binding qca,ignore-power-on-sel used to ignore +power on strapping and use sw regs instead. +Document qca,led-open.drain to set led to open drain mode, the +qca,ignore-power-on-sel is mandatory with this enabled or an error will +be reported. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 11 +++++++++++ + 1 file changed, 11 insertions(+) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -13,6 +13,17 @@ Required properties: + Optional properties: + + - reset-gpios: GPIO to be used to reset the whole device ++- qca,ignore-power-on-sel: Ignore power on pin strapping to configure led open ++ drain or eeprom presence. This is needed for broken ++ devices that have wrong configuration or when the oem ++ decided to not use pin strapping and fallback to sw ++ regs. ++- qca,led-open-drain: Set leds to open-drain mode. This requires the ++ qca,ignore-power-on-sel to be set or the driver will fail ++ to probe. This is needed if the oem doesn't use pin ++ strapping to set this mode and prefers to set it using sw ++ regs. The pin strapping related to led open drain mode is ++ the pin B68 for QCA832x and B49 for QCA833x + + Subnodes: + diff --git a/target/linux/generic/backport-5.10/747-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch b/target/linux/generic/backport-5.10/747-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch new file mode 100644 index 0000000000..aa5d92a4fd --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch @@ -0,0 +1,92 @@ +From 362bb238d8bf1470424214a8a5968d9c6cce68fa Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:15 +0200 +Subject: net: dsa: qca8k: add support for pws config reg + +Some qca8327 switch require to force the ignore of power on sel +strapping. Some switch require to set the led open drain mode in regs +instead of using strapping. While most of the device implements this +using the correct way using pin strapping, there are still some broken +device that require to be set using sw regs. +Introduce a new binding and support these special configuration. +As led open drain require to ignore pin strapping to work, the probe +fails with EINVAL error with incorrect configuration. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 39 +++++++++++++++++++++++++++++++++++++++ + drivers/net/dsa/qca8k.h | 6 ++++++ + 2 files changed, 45 insertions(+) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -932,6 +932,41 @@ static int qca8k_find_cpu_port(struct ds + } + + static int ++qca8k_setup_of_pws_reg(struct qca8k_priv *priv) ++{ ++ struct device_node *node = priv->dev->of_node; ++ u32 val = 0; ++ int ret; ++ ++ /* QCA8327 require to set to the correct mode. ++ * His bigger brother QCA8328 have the 172 pin layout. ++ * Should be applied by default but we set this just to make sure. ++ */ ++ if (priv->switch_id == QCA8K_ID_QCA8327) { ++ ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN, ++ QCA8327_PWS_PACKAGE148_EN); ++ if (ret) ++ return ret; ++ } ++ ++ if (of_property_read_bool(node, "qca,ignore-power-on-sel")) ++ val |= QCA8K_PWS_POWER_ON_SEL; ++ ++ if (of_property_read_bool(node, "qca,led-open-drain")) { ++ if (!(val & QCA8K_PWS_POWER_ON_SEL)) { ++ dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set."); ++ return -EINVAL; ++ } ++ ++ val |= QCA8K_PWS_LED_OPEN_EN_CSR; ++ } ++ ++ return qca8k_rmw(priv, QCA8K_REG_PWS, ++ QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL, ++ val); ++} ++ ++static int + qca8k_parse_port_config(struct qca8k_priv *priv) + { + int port, cpu_port_index = 0, ret; +@@ -1053,6 +1088,10 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + ++ ret = qca8k_setup_of_pws_reg(priv); ++ if (ret) ++ return ret; ++ + ret = qca8k_setup_mac_pwr_sel(priv); + if (ret) + return ret; +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -46,6 +46,12 @@ + #define QCA8K_MAX_DELAY 3 + #define QCA8K_PORT_PAD_SGMII_EN BIT(7) + #define QCA8K_REG_PWS 0x010 ++#define QCA8K_PWS_POWER_ON_SEL BIT(31) ++/* This reg is only valid for QCA832x and toggle the package ++ * type from 176 pin (by default) to 148 pin used on QCA8327 ++ */ ++#define QCA8327_PWS_PACKAGE148_EN BIT(30) ++#define QCA8K_PWS_LED_OPEN_EN_CSR BIT(24) + #define QCA8K_PWS_SERDES_AEN_DIS BIT(7) + #define QCA8K_REG_MODULE_EN 0x030 + #define QCA8K_MODULE_EN_MIB BIT(0) diff --git a/target/linux/generic/backport-5.10/747-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch b/target/linux/generic/backport-5.10/747-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch new file mode 100644 index 0000000000..1bfb00c5b2 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch @@ -0,0 +1,32 @@ +From ed7988d77fbfb79366b68f9e7fa60a6080da23d4 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:16 +0200 +Subject: dt-bindings: net: dsa: qca8k: document support for qca8328 + +QCA8328 is the bigger brother of qca8327. Document the new compatible +binding and add some information to understand the various switch +compatible. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/dsa/qca8k.txt | 7 ++++--- + 1 file changed, 4 insertions(+), 3 deletions(-) + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt +@@ -3,9 +3,10 @@ + Required properties: + + - compatible: should be one of: +- "qca,qca8327" +- "qca,qca8334" +- "qca,qca8337" ++ "qca,qca8328": referenced as AR8328(N)-AK1(A/B) QFN 176 pin package ++ "qca,qca8327": referenced as AR8327(N)-AL1A DR-QFN 148 pin package ++ "qca,qca8334": referenced as QCA8334-AL3C QFN 88 pin package ++ "qca,qca8337": referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package + + - #size-cells: must be 0 + - #address-cells: must be 1 diff --git a/target/linux/generic/backport-5.10/747-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch b/target/linux/generic/backport-5.10/747-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch new file mode 100644 index 0000000000..6e118f5a14 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch @@ -0,0 +1,78 @@ +From f477d1c8bdbef4f400718238e350f16f521d2a3e Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:17 +0200 +Subject: net: dsa: qca8k: add support for QCA8328 + +QCA8328 switch is the bigger brother of the qca8327. Same regs different +chip. Change the function to set the correct pin layout and introduce a +new match_data to differentiate the 2 switch as they have the same ID +and their internal PHY have the same ID. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 19 ++++++++++++++++--- + drivers/net/dsa/qca8k.h | 1 + + 2 files changed, 17 insertions(+), 3 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -935,6 +935,7 @@ static int + qca8k_setup_of_pws_reg(struct qca8k_priv *priv) + { + struct device_node *node = priv->dev->of_node; ++ const struct qca8k_match_data *data; + u32 val = 0; + int ret; + +@@ -943,8 +944,14 @@ qca8k_setup_of_pws_reg(struct qca8k_priv + * Should be applied by default but we set this just to make sure. + */ + if (priv->switch_id == QCA8K_ID_QCA8327) { ++ data = of_device_get_match_data(priv->dev); ++ ++ /* Set the correct package of 148 pin for QCA8327 */ ++ if (data->reduced_package) ++ val |= QCA8327_PWS_PACKAGE148_EN; ++ + ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN, +- QCA8327_PWS_PACKAGE148_EN); ++ val); + if (ret) + return ret; + } +@@ -2098,7 +2105,12 @@ static int qca8k_resume(struct device *d + static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, + qca8k_suspend, qca8k_resume); + +-static const struct qca8k_match_data qca832x = { ++static const struct qca8k_match_data qca8327 = { ++ .id = QCA8K_ID_QCA8327, ++ .reduced_package = true, ++}; ++ ++static const struct qca8k_match_data qca8328 = { + .id = QCA8K_ID_QCA8327, + }; + +@@ -2107,7 +2119,8 @@ static const struct qca8k_match_data qca + }; + + static const struct of_device_id qca8k_of_match[] = { +- { .compatible = "qca,qca8327", .data = &qca832x }, ++ { .compatible = "qca,qca8327", .data = &qca8327 }, ++ { .compatible = "qca,qca8328", .data = &qca8328 }, + { .compatible = "qca,qca8334", .data = &qca833x }, + { .compatible = "qca,qca8337", .data = &qca833x }, + { /* sentinel */ }, +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -260,6 +260,7 @@ struct ar8xxx_port_status { + + struct qca8k_match_data { + u8 id; ++ bool reduced_package; + }; + + enum { diff --git a/target/linux/generic/backport-5.10/747-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch b/target/linux/generic/backport-5.10/747-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch new file mode 100644 index 0000000000..27f94dca02 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch @@ -0,0 +1,159 @@ +From cef08115846e581f80ff99abf7bf218da1840616 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:18 +0200 +Subject: net: dsa: qca8k: set internal delay also for sgmii + +QCA original code report port instability and sa that SGMII also require +to set internal delay. Generalize the rgmii delay function and apply the +advised value if they are not defined in DT. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 88 +++++++++++++++++++++++++++++++++---------------- + drivers/net/dsa/qca8k.h | 2 ++ + 2 files changed, 62 insertions(+), 28 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1004,6 +1004,7 @@ qca8k_parse_port_config(struct qca8k_pri + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: ++ case PHY_INTERFACE_MODE_SGMII: + delay = 0; + + if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay)) +@@ -1036,8 +1037,13 @@ qca8k_parse_port_config(struct qca8k_pri + + priv->rgmii_rx_delay[cpu_port_index] = delay; + +- break; +- case PHY_INTERFACE_MODE_SGMII: ++ /* Skip sgmii parsing for rgmii* mode */ ++ if (mode == PHY_INTERFACE_MODE_RGMII || ++ mode == PHY_INTERFACE_MODE_RGMII_ID || ++ mode == PHY_INTERFACE_MODE_RGMII_TXID || ++ mode == PHY_INTERFACE_MODE_RGMII_RXID) ++ break; ++ + if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) + priv->sgmii_tx_clk_falling_edge = true; + +@@ -1261,12 +1267,53 @@ qca8k_setup(struct dsa_switch *ds) + } + + static void ++qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index, ++ u32 reg) ++{ ++ u32 delay, val = 0; ++ int ret; ++ ++ /* Delay can be declared in 3 different way. ++ * Mode to rgmii and internal-delay standard binding defined ++ * rgmii-id or rgmii-tx/rx phy mode set. ++ * The parse logic set a delay different than 0 only when one ++ * of the 3 different way is used. In all other case delay is ++ * not enabled. With ID or TX/RXID delay is enabled and set ++ * to the default and recommended value. ++ */ ++ if (priv->rgmii_tx_delay[cpu_port_index]) { ++ delay = priv->rgmii_tx_delay[cpu_port_index]; ++ ++ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | ++ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; ++ } ++ ++ if (priv->rgmii_rx_delay[cpu_port_index]) { ++ delay = priv->rgmii_rx_delay[cpu_port_index]; ++ ++ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; ++ } ++ ++ /* Set RGMII delay based on the selected values */ ++ ret = qca8k_rmw(priv, reg, ++ QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK | ++ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | ++ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN, ++ val); ++ if (ret) ++ dev_err(priv->dev, "Failed to set internal delay for CPU port%d", ++ cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6); ++} ++ ++static void + qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode, + const struct phylink_link_state *state) + { + struct qca8k_priv *priv = ds->priv; + int cpu_port_index, ret; +- u32 reg, val, delay; ++ u32 reg, val; + + switch (port) { + case 0: /* 1st CPU port */ +@@ -1315,32 +1362,10 @@ qca8k_phylink_mac_config(struct dsa_swit + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: +- val = QCA8K_PORT_PAD_RGMII_EN; +- +- /* Delay can be declared in 3 different way. +- * Mode to rgmii and internal-delay standard binding defined +- * rgmii-id or rgmii-tx/rx phy mode set. +- * The parse logic set a delay different than 0 only when one +- * of the 3 different way is used. In all other case delay is +- * not enabled. With ID or TX/RXID delay is enabled and set +- * to the default and recommended value. +- */ +- if (priv->rgmii_tx_delay[cpu_port_index]) { +- delay = priv->rgmii_tx_delay[cpu_port_index]; +- +- val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | +- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; +- } +- +- if (priv->rgmii_rx_delay[cpu_port_index]) { +- delay = priv->rgmii_rx_delay[cpu_port_index]; +- +- val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | +- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; +- } ++ qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); + +- /* Set RGMII delay based on the selected values */ +- qca8k_write(priv, reg, val); ++ /* Configure rgmii delay */ ++ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); + + /* QCA8337 requires to set rgmii rx delay for all ports. + * This is enabled through PORT5_PAD_CTRL for all ports, +@@ -1411,6 +1436,13 @@ qca8k_phylink_mac_config(struct dsa_swit + QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE | + QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, + val); ++ ++ /* From original code is reported port instability as SGMII also ++ * require delay set. Apply advised values here or take them from DT. ++ */ ++ if (state->interface == PHY_INTERFACE_MODE_SGMII) ++ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); ++ + break; + default: + dev_err(ds->dev, "xMII mode %s not supported for port %d\n", +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -39,7 +39,9 @@ + #define QCA8K_REG_PORT5_PAD_CTRL 0x008 + #define QCA8K_REG_PORT6_PAD_CTRL 0x00c + #define QCA8K_PORT_PAD_RGMII_EN BIT(26) ++#define QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK GENMASK(23, 22) + #define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) ((x) << 22) ++#define QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK GENMASK(21, 20) + #define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) ((x) << 20) + #define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25) + #define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24) diff --git a/target/linux/generic/backport-5.10/747-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch b/target/linux/generic/backport-5.10/747-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch new file mode 100644 index 0000000000..b991798c87 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch @@ -0,0 +1,124 @@ +From fd0bb28c547f7c8affb1691128cece38f5b626a1 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:19 +0200 +Subject: net: dsa: qca8k: move port config to dedicated struct + +Move ports related config to dedicated struct to keep things organized. + +Signed-off-by: Ansuel Smith +Reviewed-by: Florian Fainelli +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 26 +++++++++++++------------- + drivers/net/dsa/qca8k.h | 10 +++++++--- + 2 files changed, 20 insertions(+), 16 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1019,7 +1019,7 @@ qca8k_parse_port_config(struct qca8k_pri + delay = 3; + } + +- priv->rgmii_tx_delay[cpu_port_index] = delay; ++ priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay; + + delay = 0; + +@@ -1035,7 +1035,7 @@ qca8k_parse_port_config(struct qca8k_pri + delay = 3; + } + +- priv->rgmii_rx_delay[cpu_port_index] = delay; ++ priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay; + + /* Skip sgmii parsing for rgmii* mode */ + if (mode == PHY_INTERFACE_MODE_RGMII || +@@ -1045,17 +1045,17 @@ qca8k_parse_port_config(struct qca8k_pri + break; + + if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) +- priv->sgmii_tx_clk_falling_edge = true; ++ priv->ports_config.sgmii_tx_clk_falling_edge = true; + + if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) +- priv->sgmii_rx_clk_falling_edge = true; ++ priv->ports_config.sgmii_rx_clk_falling_edge = true; + + if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) { +- priv->sgmii_enable_pll = true; ++ priv->ports_config.sgmii_enable_pll = true; + + if (priv->switch_id == QCA8K_ID_QCA8327) { + dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling"); +- priv->sgmii_enable_pll = false; ++ priv->ports_config.sgmii_enable_pll = false; + } + + if (priv->switch_revision < 2) +@@ -1281,15 +1281,15 @@ qca8k_mac_config_setup_internal_delay(st + * not enabled. With ID or TX/RXID delay is enabled and set + * to the default and recommended value. + */ +- if (priv->rgmii_tx_delay[cpu_port_index]) { +- delay = priv->rgmii_tx_delay[cpu_port_index]; ++ if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) { ++ delay = priv->ports_config.rgmii_tx_delay[cpu_port_index]; + + val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | + QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; + } + +- if (priv->rgmii_rx_delay[cpu_port_index]) { +- delay = priv->rgmii_rx_delay[cpu_port_index]; ++ if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) { ++ delay = priv->ports_config.rgmii_rx_delay[cpu_port_index]; + + val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | + QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; +@@ -1397,7 +1397,7 @@ qca8k_phylink_mac_config(struct dsa_swit + + val |= QCA8K_SGMII_EN_SD; + +- if (priv->sgmii_enable_pll) ++ if (priv->ports_config.sgmii_enable_pll) + val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | + QCA8K_SGMII_EN_TX; + +@@ -1425,10 +1425,10 @@ qca8k_phylink_mac_config(struct dsa_swit + val = 0; + + /* SGMII Clock phase configuration */ +- if (priv->sgmii_rx_clk_falling_edge) ++ if (priv->ports_config.sgmii_rx_clk_falling_edge) + val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE; + +- if (priv->sgmii_tx_clk_falling_edge) ++ if (priv->ports_config.sgmii_tx_clk_falling_edge) + val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE; + + if (val) +--- a/drivers/net/dsa/qca8k.h ++++ b/drivers/net/dsa/qca8k.h +@@ -270,15 +270,19 @@ enum { + QCA8K_CPU_PORT6, + }; + +-struct qca8k_priv { +- u8 switch_id; +- u8 switch_revision; ++struct qca8k_ports_config { + bool sgmii_rx_clk_falling_edge; + bool sgmii_tx_clk_falling_edge; + bool sgmii_enable_pll; + u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ + u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ ++}; ++ ++struct qca8k_priv { ++ u8 switch_id; ++ u8 switch_revision; + bool legacy_phy_port_mapping; ++ struct qca8k_ports_config ports_config; + struct regmap *regmap; + struct mii_bus *bus; + struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/747-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch b/target/linux/generic/backport-5.10/747-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch new file mode 100644 index 0000000000..f7cb514176 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch @@ -0,0 +1,26 @@ +From e52073a8e3086046a098b8a7cbeb282ff0cdb424 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Thu, 14 Oct 2021 00:39:20 +0200 +Subject: dt-bindings: net: ipq8064-mdio: fix warning with new qca8k switch + +Fix warning now that we have qca8k switch Documentation using yaml. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml | 5 ++++- + 1 file changed, 4 insertions(+), 1 deletion(-) + +--- a/Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml ++++ b/Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml +@@ -51,6 +51,9 @@ examples: + switch@10 { + compatible = "qca,qca8337"; + reg = <0x10>; +- /* ... */ ++ ++ ports { ++ /* ... */ ++ }; + }; + }; diff --git a/target/linux/generic/backport-5.10/747-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch b/target/linux/generic/backport-5.10/747-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch new file mode 100644 index 0000000000..b9bce97dd3 --- /dev/null +++ b/target/linux/generic/backport-5.10/747-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch @@ -0,0 +1,631 @@ +From d291fbb8245d5ba04979fed85575860a5cea7196 Mon Sep 17 00:00:00 2001 +From: Matthew Hagan +Date: Thu, 14 Oct 2021 00:39:21 +0200 +Subject: dt-bindings: net: dsa: qca8k: convert to YAML schema + +Convert the qca8k bindings to YAML format. + +Signed-off-by: Matthew Hagan +Co-developed-by: Ansuel Smith +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + .../devicetree/bindings/net/dsa/qca8k.txt | 245 -------------- + .../devicetree/bindings/net/dsa/qca8k.yaml | 362 +++++++++++++++++++++ + 2 files changed, 362 insertions(+), 245 deletions(-) + delete mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.txt + create mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.yaml + +--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt ++++ /dev/null +@@ -1,245 +0,0 @@ +-* Qualcomm Atheros QCA8xxx switch family +- +-Required properties: +- +-- compatible: should be one of: +- "qca,qca8328": referenced as AR8328(N)-AK1(A/B) QFN 176 pin package +- "qca,qca8327": referenced as AR8327(N)-AL1A DR-QFN 148 pin package +- "qca,qca8334": referenced as QCA8334-AL3C QFN 88 pin package +- "qca,qca8337": referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package +- +-- #size-cells: must be 0 +-- #address-cells: must be 1 +- +-Optional properties: +- +-- reset-gpios: GPIO to be used to reset the whole device +-- qca,ignore-power-on-sel: Ignore power on pin strapping to configure led open +- drain or eeprom presence. This is needed for broken +- devices that have wrong configuration or when the oem +- decided to not use pin strapping and fallback to sw +- regs. +-- qca,led-open-drain: Set leds to open-drain mode. This requires the +- qca,ignore-power-on-sel to be set or the driver will fail +- to probe. This is needed if the oem doesn't use pin +- strapping to set this mode and prefers to set it using sw +- regs. The pin strapping related to led open drain mode is +- the pin B68 for QCA832x and B49 for QCA833x +- +-Subnodes: +- +-The integrated switch subnode should be specified according to the binding +-described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +-mdio-bus each subnode describing a port needs to have a valid phandle +-referencing the internal PHY it is connected to. This is because there's no +-N:N mapping of port and PHY id. +-To declare the internal mdio-bus configuration, declare a mdio node in the +-switch node and declare the phandle for the port referencing the internal +-PHY is connected to. In this config a internal mdio-bus is registered and +-the mdio MASTER is used as communication. +- +-Don't use mixed external and internal mdio-bus configurations, as this is +-not supported by the hardware. +- +-This switch support 2 CPU port. Normally and advised configuration is with +-CPU port set to port 0. It is also possible to set the CPU port to port 6 +-if the device requires it. The driver will configure the switch to the defined +-port. With both CPU port declared the first CPU port is selected as primary +-and the secondary CPU ignored. +- +-A CPU port node has the following optional node: +- +-- fixed-link : Fixed-link subnode describing a link to a non-MDIO +- managed entity. See +- Documentation/devicetree/bindings/net/fixed-link.txt +- for details. +-- qca,sgmii-rxclk-falling-edge: Set the receive clock phase to falling edge. +- Mostly used in qca8327 with CPU port 0 set to +- sgmii. +-- qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. +-- qca,sgmii-enable-pll : For SGMII CPU port, explicitly enable PLL, TX and RX +- chain along with Signal Detection. +- This should NOT be enabled for qca8327. If enabled with +- qca8327 the sgmii port won't correctly init and an err +- is printed. +- This can be required for qca8337 switch with revision 2. +- A warning is displayed when used with revision greater +- 2. +- With CPU port set to sgmii and qca8337 it is advised +- to set this unless a communication problem is observed. +- +-For QCA8K the 'fixed-link' sub-node supports only the following properties: +- +-- 'speed' (integer, mandatory), to indicate the link speed. Accepted +- values are 10, 100 and 1000 +-- 'full-duplex' (boolean, optional), to indicate that full duplex is +- used. When absent, half duplex is assumed. +- +-Examples: +- +-for the external mdio-bus configuration: +- +- &mdio0 { +- phy_port1: phy@0 { +- reg = <0>; +- }; +- +- phy_port2: phy@1 { +- reg = <1>; +- }; +- +- phy_port3: phy@2 { +- reg = <2>; +- }; +- +- phy_port4: phy@3 { +- reg = <3>; +- }; +- +- phy_port5: phy@4 { +- reg = <4>; +- }; +- +- switch@10 { +- compatible = "qca,qca8337"; +- #address-cells = <1>; +- #size-cells = <0>; +- +- reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; +- reg = <0x10>; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- port@0 { +- reg = <0>; +- label = "cpu"; +- ethernet = <&gmac1>; +- phy-mode = "rgmii"; +- fixed-link { +- speed = 1000; +- full-duplex; +- }; +- }; +- +- port@1 { +- reg = <1>; +- label = "lan1"; +- phy-handle = <&phy_port1>; +- }; +- +- port@2 { +- reg = <2>; +- label = "lan2"; +- phy-handle = <&phy_port2>; +- }; +- +- port@3 { +- reg = <3>; +- label = "lan3"; +- phy-handle = <&phy_port3>; +- }; +- +- port@4 { +- reg = <4>; +- label = "lan4"; +- phy-handle = <&phy_port4>; +- }; +- +- port@5 { +- reg = <5>; +- label = "wan"; +- phy-handle = <&phy_port5>; +- }; +- }; +- }; +- }; +- +-for the internal master mdio-bus configuration: +- +- &mdio0 { +- switch@10 { +- compatible = "qca,qca8337"; +- #address-cells = <1>; +- #size-cells = <0>; +- +- reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; +- reg = <0x10>; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- +- port@0 { +- reg = <0>; +- label = "cpu"; +- ethernet = <&gmac1>; +- phy-mode = "rgmii"; +- fixed-link { +- speed = 1000; +- full-duplex; +- }; +- }; +- +- port@1 { +- reg = <1>; +- label = "lan1"; +- phy-mode = "internal"; +- phy-handle = <&phy_port1>; +- }; +- +- port@2 { +- reg = <2>; +- label = "lan2"; +- phy-mode = "internal"; +- phy-handle = <&phy_port2>; +- }; +- +- port@3 { +- reg = <3>; +- label = "lan3"; +- phy-mode = "internal"; +- phy-handle = <&phy_port3>; +- }; +- +- port@4 { +- reg = <4>; +- label = "lan4"; +- phy-mode = "internal"; +- phy-handle = <&phy_port4>; +- }; +- +- port@5 { +- reg = <5>; +- label = "wan"; +- phy-mode = "internal"; +- phy-handle = <&phy_port5>; +- }; +- }; +- +- mdio { +- #address-cells = <1>; +- #size-cells = <0>; +- +- phy_port1: phy@0 { +- reg = <0>; +- }; +- +- phy_port2: phy@1 { +- reg = <1>; +- }; +- +- phy_port3: phy@2 { +- reg = <2>; +- }; +- +- phy_port4: phy@3 { +- reg = <3>; +- }; +- +- phy_port5: phy@4 { +- reg = <4>; +- }; +- }; +- }; +- }; +--- /dev/null ++++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml +@@ -0,0 +1,362 @@ ++# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) ++%YAML 1.2 ++--- ++$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# ++$schema: http://devicetree.org/meta-schemas/core.yaml# ++ ++title: Qualcomm Atheros QCA83xx switch family ++ ++maintainers: ++ - John Crispin ++ ++description: ++ If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode ++ describing a port needs to have a valid phandle referencing the internal PHY ++ it is connected to. This is because there is no N:N mapping of port and PHY ++ ID. To declare the internal mdio-bus configuration, declare an MDIO node in ++ the switch node and declare the phandle for the port, referencing the internal ++ PHY it is connected to. In this config, an internal mdio-bus is registered and ++ the MDIO master is used for communication. Mixed external and internal ++ mdio-bus configurations are not supported by the hardware. ++ ++properties: ++ compatible: ++ oneOf: ++ - enum: ++ - qca,qca8327 ++ - qca,qca8328 ++ - qca,qca8334 ++ - qca,qca8337 ++ description: | ++ qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package ++ qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package ++ qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package ++ qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package ++ ++ reg: ++ maxItems: 1 ++ ++ reset-gpios: ++ description: ++ GPIO to be used to reset the whole device ++ maxItems: 1 ++ ++ qca,ignore-power-on-sel: ++ $ref: /schemas/types.yaml#/definitions/flag ++ description: ++ Ignore power-on pin strapping to configure LED open-drain or EEPROM ++ presence. This is needed for devices with incorrect configuration or when ++ the OEM has decided not to use pin strapping and falls back to SW regs. ++ ++ qca,led-open-drain: ++ $ref: /schemas/types.yaml#/definitions/flag ++ description: ++ Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to ++ be set, otherwise the driver will fail at probe. This is required if the ++ OEM does not use pin strapping to set this mode and prefers to set it ++ using SW regs. The pin strappings related to LED open-drain mode are ++ B68 on the QCA832x and B49 on the QCA833x. ++ ++ mdio: ++ type: object ++ description: Qca8k switch have an internal mdio to access switch port. ++ If this is not present, the legacy mapping is used and the ++ internal mdio access is used. ++ With the legacy mapping the reg corresponding to the internal ++ mdio is the switch reg with an offset of -1. ++ ++ properties: ++ '#address-cells': ++ const: 1 ++ '#size-cells': ++ const: 0 ++ ++ patternProperties: ++ "^(ethernet-)?phy@[0-4]$": ++ type: object ++ ++ allOf: ++ - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" ++ ++ properties: ++ reg: ++ maxItems: 1 ++ ++ required: ++ - reg ++ ++patternProperties: ++ "^(ethernet-)?ports$": ++ type: object ++ properties: ++ '#address-cells': ++ const: 1 ++ '#size-cells': ++ const: 0 ++ ++ patternProperties: ++ "^(ethernet-)?port@[0-6]$": ++ type: object ++ description: Ethernet switch ports ++ ++ properties: ++ reg: ++ description: Port number ++ ++ label: ++ description: ++ Describes the label associated with this port, which will become ++ the netdev name ++ $ref: /schemas/types.yaml#/definitions/string ++ ++ link: ++ description: ++ Should be a list of phandles to other switch's DSA port. This ++ port is used as the outgoing port towards the phandle ports. The ++ full routing information must be given, not just the one hop ++ routes to neighbouring switches ++ $ref: /schemas/types.yaml#/definitions/phandle-array ++ ++ ethernet: ++ description: ++ Should be a phandle to a valid Ethernet device node. This host ++ device is what the switch port is connected to ++ $ref: /schemas/types.yaml#/definitions/phandle ++ ++ phy-handle: true ++ ++ phy-mode: true ++ ++ fixed-link: true ++ ++ mac-address: true ++ ++ sfp: true ++ ++ qca,sgmii-rxclk-falling-edge: ++ $ref: /schemas/types.yaml#/definitions/flag ++ description: ++ Set the receive clock phase to falling edge. Mostly commonly used on ++ the QCA8327 with CPU port 0 set to SGMII. ++ ++ qca,sgmii-txclk-falling-edge: ++ $ref: /schemas/types.yaml#/definitions/flag ++ description: ++ Set the transmit clock phase to falling edge. ++ ++ qca,sgmii-enable-pll: ++ $ref: /schemas/types.yaml#/definitions/flag ++ description: ++ For SGMII CPU port, explicitly enable PLL, TX and RX chain along with ++ Signal Detection. On the QCA8327 this should not be enabled, otherwise ++ the SGMII port will not initialize. When used on the QCA8337, revision 3 ++ or greater, a warning will be displayed. When the CPU port is set to ++ SGMII on the QCA8337, it is advised to set this unless a communication ++ issue is observed. ++ ++ required: ++ - reg ++ ++ additionalProperties: false ++ ++oneOf: ++ - required: ++ - ports ++ - required: ++ - ethernet-ports ++ ++required: ++ - compatible ++ - reg ++ ++additionalProperties: true ++ ++examples: ++ - | ++ #include ++ ++ mdio { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ external_phy_port1: ethernet-phy@0 { ++ reg = <0>; ++ }; ++ ++ external_phy_port2: ethernet-phy@1 { ++ reg = <1>; ++ }; ++ ++ external_phy_port3: ethernet-phy@2 { ++ reg = <2>; ++ }; ++ ++ external_phy_port4: ethernet-phy@3 { ++ reg = <3>; ++ }; ++ ++ external_phy_port5: ethernet-phy@4 { ++ reg = <4>; ++ }; ++ ++ switch@10 { ++ compatible = "qca,qca8337"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; ++ reg = <0x10>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ port@0 { ++ reg = <0>; ++ label = "cpu"; ++ ethernet = <&gmac1>; ++ phy-mode = "rgmii"; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "lan1"; ++ phy-handle = <&external_phy_port1>; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "lan2"; ++ phy-handle = <&external_phy_port2>; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "lan3"; ++ phy-handle = <&external_phy_port3>; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "lan4"; ++ phy-handle = <&external_phy_port4>; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ label = "wan"; ++ phy-handle = <&external_phy_port5>; ++ }; ++ }; ++ }; ++ }; ++ - | ++ #include ++ ++ mdio { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ switch@10 { ++ compatible = "qca,qca8337"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; ++ reg = <0x10>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ port@0 { ++ reg = <0>; ++ label = "cpu"; ++ ethernet = <&gmac1>; ++ phy-mode = "rgmii"; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "lan1"; ++ phy-mode = "internal"; ++ phy-handle = <&internal_phy_port1>; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "lan2"; ++ phy-mode = "internal"; ++ phy-handle = <&internal_phy_port2>; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "lan3"; ++ phy-mode = "internal"; ++ phy-handle = <&internal_phy_port3>; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "lan4"; ++ phy-mode = "internal"; ++ phy-handle = <&internal_phy_port4>; ++ }; ++ ++ port@5 { ++ reg = <5>; ++ label = "wan"; ++ phy-mode = "internal"; ++ phy-handle = <&internal_phy_port5>; ++ }; ++ ++ port@6 { ++ reg = <0>; ++ label = "cpu"; ++ ethernet = <&gmac1>; ++ phy-mode = "sgmii"; ++ ++ qca,sgmii-rxclk-falling-edge; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ }; ++ ++ mdio { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ internal_phy_port1: ethernet-phy@0 { ++ reg = <0>; ++ }; ++ ++ internal_phy_port2: ethernet-phy@1 { ++ reg = <1>; ++ }; ++ ++ internal_phy_port3: ethernet-phy@2 { ++ reg = <2>; ++ }; ++ ++ internal_phy_port4: ethernet-phy@3 { ++ reg = <3>; ++ }; ++ ++ internal_phy_port5: ethernet-phy@4 { ++ reg = <4>; ++ }; ++ }; ++ }; ++ }; diff --git a/target/linux/generic/backport-5.10/748-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch b/target/linux/generic/backport-5.10/748-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch new file mode 100644 index 0000000000..a510cfdc18 --- /dev/null +++ b/target/linux/generic/backport-5.10/748-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch @@ -0,0 +1,28 @@ +From 06dd34a628ae5b6a839b757e746de165d6789ca8 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Sun, 17 Oct 2021 16:56:46 +0200 +Subject: net: dsa: qca8k: fix delay applied to wrong cpu in parse_port_config + +Fix delay settings applied to wrong cpu in parse_port_config. The delay +values is set to the wrong index as the cpu_port_index is incremented +too early. Start the cpu_port_index to -1 so the correct value is +applied to address also the case with invalid phy mode and not available +port. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -976,7 +976,7 @@ qca8k_setup_of_pws_reg(struct qca8k_priv + static int + qca8k_parse_port_config(struct qca8k_priv *priv) + { +- int port, cpu_port_index = 0, ret; ++ int port, cpu_port_index = -1, ret; + struct device_node *port_dn; + phy_interface_t mode; + struct dsa_port *dp; diff --git a/target/linux/generic/backport-5.10/749-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch b/target/linux/generic/backport-5.10/749-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch new file mode 100644 index 0000000000..71fa3022d5 --- /dev/null +++ b/target/linux/generic/backport-5.10/749-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch @@ -0,0 +1,151 @@ +From 040e926f5813a5f4cc18dbff7c942d1e52f368f2 Mon Sep 17 00:00:00 2001 +From: Ansuel Smith +Date: Tue, 19 Oct 2021 02:08:50 +0200 +Subject: net: dsa: qca8k: tidy for loop in setup and add cpu port check + +Tidy and organize qca8k setup function from multiple for loop. +Change for loop in bridge leave/join to scan all port and skip cpu port. +No functional change intended. + +Signed-off-by: Ansuel Smith +Signed-off-by: David S. Miller +--- + drivers/net/dsa/qca8k.c | 74 +++++++++++++++++++++++++++++-------------------- + 1 file changed, 44 insertions(+), 30 deletions(-) + +--- a/drivers/net/dsa/qca8k.c ++++ b/drivers/net/dsa/qca8k.c +@@ -1122,28 +1122,34 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + dev_warn(priv->dev, "mib init failed"); + +- /* Enable QCA header mode on the cpu port */ +- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(cpu_port), +- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | +- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); +- if (ret) { +- dev_err(priv->dev, "failed enabling QCA header mode"); +- return ret; +- } +- +- /* Disable forwarding by default on all ports */ ++ /* Initial setup of all ports */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ /* Disable forwarding by default on all ports */ + ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), + QCA8K_PORT_LOOKUP_MEMBER, 0); + if (ret) + return ret; +- } + +- /* Disable MAC by default on all ports */ +- for (i = 1; i < QCA8K_NUM_PORTS; i++) +- qca8k_port_set_status(priv, i, 0); ++ /* Enable QCA header mode on all cpu ports */ ++ if (dsa_is_cpu_port(ds, i)) { ++ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i), ++ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | ++ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); ++ if (ret) { ++ dev_err(priv->dev, "failed enabling QCA header mode"); ++ return ret; ++ } ++ } ++ ++ /* Disable MAC by default on all user ports */ ++ if (dsa_is_user_port(ds, i)) ++ qca8k_port_set_status(priv, i, 0); ++ } + +- /* Forward all unknown frames to CPU port for Linux processing */ ++ /* Forward all unknown frames to CPU port for Linux processing ++ * Notice that in multi-cpu config only one port should be set ++ * for igmp, unknown, multicast and broadcast packet ++ */ + ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, + BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | + BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | +@@ -1152,11 +1158,13 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + +- /* Setup connection between CPU port & user ports */ ++ /* Setup connection between CPU port & user ports ++ * Configure specific switch configuration for ports ++ */ + for (i = 0; i < QCA8K_NUM_PORTS; i++) { + /* CPU port gets connected to all user ports of the switch */ + if (dsa_is_cpu_port(ds, i)) { +- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port), ++ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), + QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); + if (ret) + return ret; +@@ -1193,16 +1201,14 @@ qca8k_setup(struct dsa_switch *ds) + if (ret) + return ret; + } +- } + +- /* The port 5 of the qca8337 have some problem in flood condition. The +- * original legacy driver had some specific buffer and priority settings +- * for the different port suggested by the QCA switch team. Add this +- * missing settings to improve switch stability under load condition. +- * This problem is limited to qca8337 and other qca8k switch are not affected. +- */ +- if (priv->switch_id == QCA8K_ID_QCA8337) { +- for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ /* The port 5 of the qca8337 have some problem in flood condition. The ++ * original legacy driver had some specific buffer and priority settings ++ * for the different port suggested by the QCA switch team. Add this ++ * missing settings to improve switch stability under load condition. ++ * This problem is limited to qca8337 and other qca8k switch are not affected. ++ */ ++ if (priv->switch_id == QCA8K_ID_QCA8337) { + switch (i) { + /* The 2 CPU port and port 5 requires some different + * priority than any other ports. +@@ -1238,6 +1244,12 @@ qca8k_setup(struct dsa_switch *ds) + QCA8K_PORT_HOL_CTRL1_WRED_EN, + mask); + } ++ ++ /* Set initial MTU for every port. ++ * We have only have a general MTU setting. So track ++ * every port and set the max across all port. ++ */ ++ priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; + } + + /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ +@@ -1251,8 +1263,6 @@ qca8k_setup(struct dsa_switch *ds) + } + + /* Setup our port MTUs to match power on defaults */ +- for (i = 0; i < QCA8K_NUM_PORTS; i++) +- priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; + ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); + if (ret) + dev_warn(priv->dev, "failed setting MTU settings"); +@@ -1728,7 +1738,9 @@ qca8k_port_bridge_join(struct dsa_switch + cpu_port = dsa_to_port(ds, port)->cpu_dp->index; + port_mask = BIT(cpu_port); + +- for (i = 1; i < QCA8K_NUM_PORTS; i++) { ++ for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ if (dsa_is_cpu_port(ds, i)) ++ continue; + if (dsa_to_port(ds, i)->bridge_dev != br) + continue; + /* Add this port to the portvlan mask of the other ports +@@ -1758,7 +1770,9 @@ qca8k_port_bridge_leave(struct dsa_switc + + cpu_port = dsa_to_port(ds, port)->cpu_dp->index; + +- for (i = 1; i < QCA8K_NUM_PORTS; i++) { ++ for (i = 0; i < QCA8K_NUM_PORTS; i++) { ++ if (dsa_is_cpu_port(ds, i)) ++ continue; + if (dsa_to_port(ds, i)->bridge_dev != br) + continue; + /* Remove this port to the portvlan mask of the other ports diff --git a/target/linux/generic/backport-5.10/765-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch b/target/linux/generic/backport-5.10/765-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch deleted file mode 100644 index 3b630377f9..0000000000 --- a/target/linux/generic/backport-5.10/765-v5.12-net-dsa-automatically-bring-up-DSA-master-when-openi.patch +++ /dev/null @@ -1,85 +0,0 @@ -From 9d5ef190e5615a7b63af89f88c4106a5bc127974 Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Fri, 5 Feb 2021 15:37:10 +0200 -Subject: [PATCH] net: dsa: automatically bring up DSA master when opening user - port - -DSA wants the master interface to be open before the user port is due to -historical reasons. The promiscuity of interfaces that are down used to -have issues, as referenced Lennert Buytenhek in commit df02c6ff2e39 -("dsa: fix master interface allmulti/promisc handling"). - -The bugfix mentioned there, commit b6c40d68ff64 ("net: only invoke -dev->change_rx_flags when device is UP"), was basically a "don't do -that" approach to working around the promiscuity while down issue. - -Further work done by Vlad Yasevich in commit d2615bf45069 ("net: core: -Always propagate flag changes to interfaces") has resolved the -underlying issue, and it is strictly up to the DSA and 8021q drivers -now, it is no longer mandated by the networking core that the master -interface must be up when changing its promiscuity. - -From DSA's point of view, deciding to error out in dsa_slave_open -because the master isn't up is -(a) a bad user experience and -(b) knocking at an open door. -Even if there still was an issue with promiscuity while down, DSA could -still just open the master and avoid it. - -Doing it this way has the additional benefit that user space can now -remove DSA-specific workarounds, like systemd-networkd with BindCarrier: -https://github.com/systemd/systemd/issues/7478 - -And we can finally remove one of the 2 bullets in the "Common pitfalls -using DSA setups" chapter. - -Tested with two cascaded DSA switches: - -$ ip link set sw0p2 up -fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode -fsl_enetc 0000:00:00.2 eno2: Link is Up - 1Gbps/Full - flow control rx/tx -mscc_felix 0000:00:00.5 swp0: configuring for fixed/sgmii link mode -mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off -8021q: adding VLAN 0 to HW filter on device swp0 -sja1105 spi2.0 sw0p2: configuring for phy/rgmii-id link mode -IPv6: ADDRCONF(NETDEV_CHANGE): eno2: link becomes ready -IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready - -Signed-off-by: Vladimir Oltean -Reviewed-by: Andrew Lunn -Reviewed-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - Documentation/networking/dsa/dsa.rst | 4 ---- - net/dsa/slave.c | 7 +++++-- - 2 files changed, 5 insertions(+), 6 deletions(-) - ---- a/Documentation/networking/dsa/dsa.rst -+++ b/Documentation/networking/dsa/dsa.rst -@@ -273,10 +273,6 @@ will not make us go through the switch t - the Ethernet switch on the other end, expecting a tag will typically drop this - frame. - --Slave network devices check that the master network device is UP before allowing --you to administratively bring UP these slave network devices. A common --configuration mistake is forgetting to bring UP the master network device first. -- - Interactions with other subsystems - ================================== - ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -68,8 +68,11 @@ static int dsa_slave_open(struct net_dev - struct dsa_port *dp = dsa_slave_to_port(dev); - int err; - -- if (!(master->flags & IFF_UP)) -- return -ENETDOWN; -+ err = dev_open(master, NULL); -+ if (err < 0) { -+ netdev_err(dev, "failed to open master %s\n", master->name); -+ goto out; -+ } - - if (!ether_addr_equal(dev->dev_addr, master->dev_addr)) { - err = dev_uc_add(master, dev->dev_addr); diff --git a/target/linux/generic/backport-5.10/770-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch b/target/linux/generic/backport-5.10/770-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch deleted file mode 100644 index c43cb4d1f2..0000000000 --- a/target/linux/generic/backport-5.10/770-v5.12-net-bridge-notify-switchdev-of-disappearance-of-old-.patch +++ /dev/null @@ -1,126 +0,0 @@ -From 90dc8fd36078a536671adae884d0b929cce6480a Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:30 +0200 -Subject: [PATCH] net: bridge: notify switchdev of disappearance of old FDB - entry upon migration - -Currently the bridge emits atomic switchdev notifications for -dynamically learnt FDB entries. Monitoring these notifications works -wonders for switchdev drivers that want to keep their hardware FDB in -sync with the bridge's FDB. - -For example station A wants to talk to station B in the diagram below, -and we are concerned with the behavior of the bridge on the DUT device: - - DUT - +-------------------------------------+ - | br0 | - | +------+ +------+ +------+ +------+ | - | | | | | | | | | | - | | swp0 | | swp1 | | swp2 | | eth0 | | - +-------------------------------------+ - | | | - Station A | | - | | - +--+------+--+ +--+------+--+ - | | | | | | | | - | | swp0 | | | | swp0 | | - Another | +------+ | | +------+ | Another - switch | br0 | | br0 | switch - | +------+ | | +------+ | - | | | | | | | | - | | swp1 | | | | swp1 | | - +--+------+--+ +--+------+--+ - | - Station B - -Interfaces swp0, swp1, swp2 are handled by a switchdev driver that has -the following property: frames injected from its control interface bypass -the internal address analyzer logic, and therefore, this hardware does -not learn from the source address of packets transmitted by the network -stack through it. So, since bridging between eth0 (where Station B is -attached) and swp0 (where Station A is attached) is done in software, -the switchdev hardware will never learn the source address of Station B. -So the traffic towards that destination will be treated as unknown, i.e. -flooded. - -This is where the bridge notifications come in handy. When br0 on the -DUT sees frames with Station B's MAC address on eth0, the switchdev -driver gets these notifications and can install a rule to send frames -towards Station B's address that are incoming from swp0, swp1, swp2, -only towards the control interface. This is all switchdev driver private -business, which the notification makes possible. - -All is fine until someone unplugs Station B's cable and moves it to the -other switch: - - DUT - +-------------------------------------+ - | br0 | - | +------+ +------+ +------+ +------+ | - | | | | | | | | | | - | | swp0 | | swp1 | | swp2 | | eth0 | | - +-------------------------------------+ - | | | - Station A | | - | | - +--+------+--+ +--+------+--+ - | | | | | | | | - | | swp0 | | | | swp0 | | - Another | +------+ | | +------+ | Another - switch | br0 | | br0 | switch - | +------+ | | +------+ | - | | | | | | | | - | | swp1 | | | | swp1 | | - +--+------+--+ +--+------+--+ - | - Station B - -Luckily for the use cases we care about, Station B is noisy enough that -the DUT hears it (on swp1 this time). swp1 receives the frames and -delivers them to the bridge, who enters the unlikely path in br_fdb_update -of updating an existing entry. It moves the entry in the software bridge -to swp1 and emits an addition notification towards that. - -As far as the switchdev driver is concerned, all that it needs to ensure -is that traffic between Station A and Station B is not forever broken. -If it does nothing, then the stale rule to send frames for Station B -towards the control interface remains in place. But Station B is no -longer reachable via the control interface, but via a port that can -offload the bridge port learning attribute. It's just that the port is -prevented from learning this address, since the rule overrides FDB -updates. So the rule needs to go. The question is via what mechanism. - -It sure would be possible for this switchdev driver to keep track of all -addresses which are sent to the control interface, and then also listen -for bridge notifier events on its own ports, searching for the ones that -have a MAC address which was previously sent to the control interface. -But this is cumbersome and inefficient. Instead, with one small change, -the bridge could notify of the address deletion from the old port, in a -symmetrical manner with how it did for the insertion. Then the switchdev -driver would not be required to monitor learn/forget events for its own -ports. It could just delete the rule towards the control interface upon -bridge entry migration. This would make hardware address learning be -possible again. Then it would take a few more packets until the hardware -and software FDB would be in sync again. - -Signed-off-by: Vladimir Oltean -Acked-by: Nikolay Aleksandrov -Reviewed-by: Ido Schimmel -Reviewed-by: Andrew Lunn -Reviewed-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - net/bridge/br_fdb.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/net/bridge/br_fdb.c -+++ b/net/bridge/br_fdb.c -@@ -602,6 +602,7 @@ void br_fdb_update(struct net_bridge *br - /* fastpath: update of existing entry */ - if (unlikely(source != fdb->dst && - !test_bit(BR_FDB_STICKY, &fdb->flags))) { -+ br_switchdev_fdb_notify(fdb, RTM_DELNEIGH); - fdb->dst = source; - fdb_modified = true; - /* Take over HW learned entry */ diff --git a/target/linux/generic/backport-5.10/771-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch b/target/linux/generic/backport-5.10/771-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch deleted file mode 100644 index f9337590f7..0000000000 --- a/target/linux/generic/backport-5.10/771-v5.12-net-dsa-be-louder-when-a-non-legacy-FDB-operation-fa.patch +++ /dev/null @@ -1,52 +0,0 @@ -From 2fd186501b1cff155cc4a755c210793cfc0dffb5 Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:31 +0200 -Subject: [PATCH] net: dsa: be louder when a non-legacy FDB operation fails - -The dev_close() call was added in commit c9eb3e0f8701 ("net: dsa: Add -support for learning FDB through notification") "to indicate inconsistent -situation" when we could not delete an FDB entry from the port. - -bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master - -It is a bit drastic and at the same time not helpful if the above fails -to only print with netdev_dbg log level, but on the other hand to bring -the interface down. - -So increase the verbosity of the error message, and drop dev_close(). - -Signed-off-by: Vladimir Oltean -Reviewed-by: Andrew Lunn -Reviewed-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - net/dsa/slave.c | 10 +++++++--- - 1 file changed, 7 insertions(+), 3 deletions(-) - ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -2112,7 +2112,9 @@ static void dsa_slave_switchdev_event_wo - - err = dsa_port_fdb_add(dp, fdb_info->addr, fdb_info->vid); - if (err) { -- netdev_dbg(dev, "fdb add failed err=%d\n", err); -+ netdev_err(dev, -+ "failed to add %pM vid %d to fdb: %d\n", -+ fdb_info->addr, fdb_info->vid, err); - break; - } - fdb_info->offloaded = true; -@@ -2127,9 +2129,11 @@ static void dsa_slave_switchdev_event_wo - - err = dsa_port_fdb_del(dp, fdb_info->addr, fdb_info->vid); - if (err) { -- netdev_dbg(dev, "fdb del failed err=%d\n", err); -- dev_close(dev); -+ netdev_err(dev, -+ "failed to delete %pM vid %d from fdb: %d\n", -+ fdb_info->addr, fdb_info->vid, err); - } -+ - break; - } - rtnl_unlock(); diff --git a/target/linux/generic/backport-5.10/772-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch b/target/linux/generic/backport-5.10/772-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch deleted file mode 100644 index c1aa8fda82..0000000000 --- a/target/linux/generic/backport-5.10/772-v5.12-net-dsa-don-t-use-switchdev_notifier_fdb_info-in-dsa.patch +++ /dev/null @@ -1,226 +0,0 @@ -From c4bb76a9a0ef87c4cc1f636defed5f12deb9f5a7 Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:32 +0200 -Subject: [PATCH] net: dsa: don't use switchdev_notifier_fdb_info in - dsa_switchdev_event_work - -Currently DSA doesn't add FDB entries on the CPU port, because it only -does so through switchdev, which is associated with a net_device, and -there are none of those for the CPU port. - -But actually FDB addresses on the CPU port have some use cases of their -own, if the switchdev operations are initiated from within the DSA -layer. There is just one problem with the existing code: it passes a -structure in dsa_switchdev_event_work which was retrieved directly from -switchdev, so it contains a net_device. We need to generalize the -contents to something that covers the CPU port as well: the "ds, port" -tuple is fine for that. - -Note that the new procedure for notifying the successful FDB offload is -inspired from the rocker model. - -Also, nothing was being done if added_by_user was false. Let's check for -that a lot earlier, and don't actually bother to schedule the worker -for nothing. - -Signed-off-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - net/dsa/dsa_priv.h | 12 +++++ - net/dsa/slave.c | 106 ++++++++++++++++++++++----------------------- - 2 files changed, 65 insertions(+), 53 deletions(-) - ---- a/net/dsa/dsa_priv.h -+++ b/net/dsa/dsa_priv.h -@@ -73,6 +73,18 @@ struct dsa_notifier_mtu_info { - int mtu; - }; - -+struct dsa_switchdev_event_work { -+ struct dsa_switch *ds; -+ int port; -+ struct work_struct work; -+ unsigned long event; -+ /* Specific for SWITCHDEV_FDB_ADD_TO_DEVICE and -+ * SWITCHDEV_FDB_DEL_TO_DEVICE -+ */ -+ unsigned char addr[ETH_ALEN]; -+ u16 vid; -+}; -+ - struct dsa_slave_priv { - /* Copy of CPU port xmit for faster access in slave transmit hot path */ - struct sk_buff * (*xmit)(struct sk_buff *skb, ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -2087,76 +2087,66 @@ static int dsa_slave_netdevice_event(str - return NOTIFY_DONE; - } - --struct dsa_switchdev_event_work { -- struct work_struct work; -- struct switchdev_notifier_fdb_info fdb_info; -- struct net_device *dev; -- unsigned long event; --}; -+static void -+dsa_fdb_offload_notify(struct dsa_switchdev_event_work *switchdev_work) -+{ -+ struct dsa_switch *ds = switchdev_work->ds; -+ struct switchdev_notifier_fdb_info info; -+ struct dsa_port *dp; -+ -+ if (!dsa_is_user_port(ds, switchdev_work->port)) -+ return; -+ -+ info.addr = switchdev_work->addr; -+ info.vid = switchdev_work->vid; -+ info.offloaded = true; -+ dp = dsa_to_port(ds, switchdev_work->port); -+ call_switchdev_notifiers(SWITCHDEV_FDB_OFFLOADED, -+ dp->slave, &info.info, NULL); -+} - - static void dsa_slave_switchdev_event_work(struct work_struct *work) - { - struct dsa_switchdev_event_work *switchdev_work = - container_of(work, struct dsa_switchdev_event_work, work); -- struct net_device *dev = switchdev_work->dev; -- struct switchdev_notifier_fdb_info *fdb_info; -- struct dsa_port *dp = dsa_slave_to_port(dev); -+ struct dsa_switch *ds = switchdev_work->ds; -+ struct dsa_port *dp; - int err; - -+ dp = dsa_to_port(ds, switchdev_work->port); -+ - rtnl_lock(); - switch (switchdev_work->event) { - case SWITCHDEV_FDB_ADD_TO_DEVICE: -- fdb_info = &switchdev_work->fdb_info; -- if (!fdb_info->added_by_user) -- break; -- -- err = dsa_port_fdb_add(dp, fdb_info->addr, fdb_info->vid); -+ err = dsa_port_fdb_add(dp, switchdev_work->addr, -+ switchdev_work->vid); - if (err) { -- netdev_err(dev, -- "failed to add %pM vid %d to fdb: %d\n", -- fdb_info->addr, fdb_info->vid, err); -+ dev_err(ds->dev, -+ "port %d failed to add %pM vid %d to fdb: %d\n", -+ dp->index, switchdev_work->addr, -+ switchdev_work->vid, err); - break; - } -- fdb_info->offloaded = true; -- call_switchdev_notifiers(SWITCHDEV_FDB_OFFLOADED, dev, -- &fdb_info->info, NULL); -+ dsa_fdb_offload_notify(switchdev_work); - break; - - case SWITCHDEV_FDB_DEL_TO_DEVICE: -- fdb_info = &switchdev_work->fdb_info; -- if (!fdb_info->added_by_user) -- break; -- -- err = dsa_port_fdb_del(dp, fdb_info->addr, fdb_info->vid); -+ err = dsa_port_fdb_del(dp, switchdev_work->addr, -+ switchdev_work->vid); - if (err) { -- netdev_err(dev, -- "failed to delete %pM vid %d from fdb: %d\n", -- fdb_info->addr, fdb_info->vid, err); -+ dev_err(ds->dev, -+ "port %d failed to delete %pM vid %d from fdb: %d\n", -+ dp->index, switchdev_work->addr, -+ switchdev_work->vid, err); - } - - break; - } - rtnl_unlock(); - -- kfree(switchdev_work->fdb_info.addr); - kfree(switchdev_work); -- dev_put(dev); --} -- --static int --dsa_slave_switchdev_fdb_work_init(struct dsa_switchdev_event_work * -- switchdev_work, -- const struct switchdev_notifier_fdb_info * -- fdb_info) --{ -- memcpy(&switchdev_work->fdb_info, fdb_info, -- sizeof(switchdev_work->fdb_info)); -- switchdev_work->fdb_info.addr = kzalloc(ETH_ALEN, GFP_ATOMIC); -- if (!switchdev_work->fdb_info.addr) -- return -ENOMEM; -- ether_addr_copy((u8 *)switchdev_work->fdb_info.addr, -- fdb_info->addr); -- return 0; -+ if (dsa_is_user_port(ds, dp->index)) -+ dev_put(dp->slave); - } - - /* Called under rcu_read_lock() */ -@@ -2164,7 +2154,9 @@ static int dsa_slave_switchdev_event(str - unsigned long event, void *ptr) - { - struct net_device *dev = switchdev_notifier_info_to_dev(ptr); -+ const struct switchdev_notifier_fdb_info *fdb_info; - struct dsa_switchdev_event_work *switchdev_work; -+ struct dsa_port *dp; - int err; - - if (event == SWITCHDEV_PORT_ATTR_SET) { -@@ -2177,20 +2169,32 @@ static int dsa_slave_switchdev_event(str - if (!dsa_slave_dev_check(dev)) - return NOTIFY_DONE; - -+ dp = dsa_slave_to_port(dev); -+ - switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); - if (!switchdev_work) - return NOTIFY_BAD; - - INIT_WORK(&switchdev_work->work, - dsa_slave_switchdev_event_work); -- switchdev_work->dev = dev; -+ switchdev_work->ds = dp->ds; -+ switchdev_work->port = dp->index; - switchdev_work->event = event; - - switch (event) { - case SWITCHDEV_FDB_ADD_TO_DEVICE: - case SWITCHDEV_FDB_DEL_TO_DEVICE: -- if (dsa_slave_switchdev_fdb_work_init(switchdev_work, ptr)) -- goto err_fdb_work_init; -+ fdb_info = ptr; -+ -+ if (!fdb_info->added_by_user) { -+ kfree(switchdev_work); -+ return NOTIFY_OK; -+ } -+ -+ ether_addr_copy(switchdev_work->addr, -+ fdb_info->addr); -+ switchdev_work->vid = fdb_info->vid; -+ - dev_hold(dev); - break; - default: -@@ -2200,10 +2204,6 @@ static int dsa_slave_switchdev_event(str - - dsa_schedule_work(&switchdev_work->work); - return NOTIFY_OK; -- --err_fdb_work_init: -- kfree(switchdev_work); -- return NOTIFY_BAD; - } - - static int dsa_slave_switchdev_blocking_event(struct notifier_block *unused, diff --git a/target/linux/generic/backport-5.10/773-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch b/target/linux/generic/backport-5.10/773-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch deleted file mode 100644 index 9131df70d3..0000000000 --- a/target/linux/generic/backport-5.10/773-v5.12-net-dsa-move-switchdev-event-implementation-under-th.patch +++ /dev/null @@ -1,85 +0,0 @@ -From 447d290a58bd335d68f665713842365d3d6447df Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:33 +0200 -Subject: [PATCH] net: dsa: move switchdev event implementation under the same - switch/case statement - -We'll need to start listening to SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE -events even for interfaces where dsa_slave_dev_check returns false, so -we need that check inside the switch-case statement for SWITCHDEV_FDB_*. - -This movement also avoids a useless allocation / free of switchdev_work -on the untreated "default event" case. - -Signed-off-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - net/dsa/slave.c | 35 ++++++++++++++++------------------- - 1 file changed, 16 insertions(+), 19 deletions(-) - ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -2159,31 +2159,29 @@ static int dsa_slave_switchdev_event(str - struct dsa_port *dp; - int err; - -- if (event == SWITCHDEV_PORT_ATTR_SET) { -+ switch (event) { -+ case SWITCHDEV_PORT_ATTR_SET: - err = switchdev_handle_port_attr_set(dev, ptr, - dsa_slave_dev_check, - dsa_slave_port_attr_set); - return notifier_from_errno(err); -- } -- -- if (!dsa_slave_dev_check(dev)) -- return NOTIFY_DONE; -+ case SWITCHDEV_FDB_ADD_TO_DEVICE: -+ case SWITCHDEV_FDB_DEL_TO_DEVICE: -+ if (!dsa_slave_dev_check(dev)) -+ return NOTIFY_DONE; - -- dp = dsa_slave_to_port(dev); -+ dp = dsa_slave_to_port(dev); - -- switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); -- if (!switchdev_work) -- return NOTIFY_BAD; -- -- INIT_WORK(&switchdev_work->work, -- dsa_slave_switchdev_event_work); -- switchdev_work->ds = dp->ds; -- switchdev_work->port = dp->index; -- switchdev_work->event = event; -+ switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); -+ if (!switchdev_work) -+ return NOTIFY_BAD; -+ -+ INIT_WORK(&switchdev_work->work, -+ dsa_slave_switchdev_event_work); -+ switchdev_work->ds = dp->ds; -+ switchdev_work->port = dp->index; -+ switchdev_work->event = event; - -- switch (event) { -- case SWITCHDEV_FDB_ADD_TO_DEVICE: -- case SWITCHDEV_FDB_DEL_TO_DEVICE: - fdb_info = ptr; - - if (!fdb_info->added_by_user) { -@@ -2196,13 +2194,12 @@ static int dsa_slave_switchdev_event(str - switchdev_work->vid = fdb_info->vid; - - dev_hold(dev); -+ dsa_schedule_work(&switchdev_work->work); - break; - default: -- kfree(switchdev_work); - return NOTIFY_DONE; - } - -- dsa_schedule_work(&switchdev_work->work); - return NOTIFY_OK; - } - diff --git a/target/linux/generic/backport-5.10/774-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch b/target/linux/generic/backport-5.10/774-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch deleted file mode 100644 index b7b6ebe461..0000000000 --- a/target/linux/generic/backport-5.10/774-v5.12-net-dsa-exit-early-in-dsa_slave_switchdev_event-if-w.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 5fb4a451a87d8ed3363d28b63a3295399373d6c4 Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:34 +0200 -Subject: [PATCH] net: dsa: exit early in dsa_slave_switchdev_event if we can't - program the FDB - -Right now, the following would happen for a switch driver that does not -implement .port_fdb_add or .port_fdb_del. - -dsa_slave_switchdev_event returns NOTIFY_OK and schedules: --> dsa_slave_switchdev_event_work - -> dsa_port_fdb_add - -> dsa_port_notify(DSA_NOTIFIER_FDB_ADD) - -> dsa_switch_fdb_add - -> if (!ds->ops->port_fdb_add) return -EOPNOTSUPP; - -> an error is printed with dev_dbg, and - dsa_fdb_offload_notify(switchdev_work) is not called. - -We can avoid scheduling the worker for nothing and say NOTIFY_DONE. -Because we don't call dsa_fdb_offload_notify, the static FDB entry will -remain just in the software bridge. - -Signed-off-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Reviewed-by: Andrew Lunn -Signed-off-by: Jakub Kicinski ---- - net/dsa/slave.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -2172,6 +2172,9 @@ static int dsa_slave_switchdev_event(str - - dp = dsa_slave_to_port(dev); - -+ if (!dp->ds->ops->port_fdb_add || !dp->ds->ops->port_fdb_del) -+ return NOTIFY_DONE; -+ - switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC); - if (!switchdev_work) - return NOTIFY_BAD; diff --git a/target/linux/generic/backport-5.10/775-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch b/target/linux/generic/backport-5.10/775-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch deleted file mode 100644 index e7b9af1951..0000000000 --- a/target/linux/generic/backport-5.10/775-v5.12-net-dsa-listen-for-SWITCHDEV_-FDB-DEL-_ADD_TO_DEVICE.patch +++ /dev/null @@ -1,264 +0,0 @@ -From d5f19486cee79d04c054427577ac96ed123706db Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Wed, 6 Jan 2021 11:51:35 +0200 -Subject: [PATCH] net: dsa: listen for SWITCHDEV_{FDB,DEL}_ADD_TO_DEVICE on - foreign bridge neighbors - -Some DSA switches (and not only) cannot learn source MAC addresses from -packets injected from the CPU. They only perform hardware address -learning from inbound traffic. - -This can be problematic when we have a bridge spanning some DSA switch -ports and some non-DSA ports (which we'll call "foreign interfaces" from -DSA's perspective). - -There are 2 classes of problems created by the lack of learning on -CPU-injected traffic: -- excessive flooding, due to the fact that DSA treats those addresses as - unknown -- the risk of stale routes, which can lead to temporary packet loss - -To illustrate the second class, consider the following situation, which -is common in production equipment (wireless access points, where there -is a WLAN interface and an Ethernet switch, and these form a single -bridging domain). - - AP 1: - +------------------------------------------------------------------------+ - | br0 | - +------------------------------------------------------------------------+ - +------------+ +------------+ +------------+ +------------+ +------------+ - | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | - +------------+ +------------+ +------------+ +------------+ +------------+ - | ^ ^ - | | | - | | | - | Client A Client B - | - | - | - +------------+ +------------+ +------------+ +------------+ +------------+ - | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | - +------------+ +------------+ +------------+ +------------+ +------------+ - +------------------------------------------------------------------------+ - | br0 | - +------------------------------------------------------------------------+ - AP 2 - -- br0 of AP 1 will know that Clients A and B are reachable via wlan0 -- the hardware fdb of a DSA switch driver today is not kept in sync with - the software entries on other bridge ports, so it will not know that - clients A and B are reachable via the CPU port UNLESS the hardware - switch itself performs SA learning from traffic injected from the CPU. - Nonetheless, a substantial number of switches don't. -- the hardware fdb of the DSA switch on AP 2 may autonomously learn that - Client A and B are reachable through swp0. Therefore, the software br0 - of AP 2 also may or may not learn this. In the example we're - illustrating, some Ethernet traffic has been going on, and br0 from AP - 2 has indeed learnt that it can reach Client B through swp0. - -One of the wireless clients, say Client B, disconnects from AP 1 and -roams to AP 2. The topology now looks like this: - - AP 1: - +------------------------------------------------------------------------+ - | br0 | - +------------------------------------------------------------------------+ - +------------+ +------------+ +------------+ +------------+ +------------+ - | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | - +------------+ +------------+ +------------+ +------------+ +------------+ - | ^ - | | - | Client A - | - | - | Client B - | | - | v - +------------+ +------------+ +------------+ +------------+ +------------+ - | swp0 | | swp1 | | swp2 | | swp3 | | wlan0 | - +------------+ +------------+ +------------+ +------------+ +------------+ - +------------------------------------------------------------------------+ - | br0 | - +------------------------------------------------------------------------+ - AP 2 - -- br0 of AP 1 still knows that Client A is reachable via wlan0 (no change) -- br0 of AP 1 will (possibly) know that Client B has left wlan0. There - are cases where it might never find out though. Either way, DSA today - does not process that notification in any way. -- the hardware FDB of the DSA switch on AP 1 may learn autonomously that - Client B can be reached via swp0, if it receives any packet with - Client 1's source MAC address over Ethernet. -- the hardware FDB of the DSA switch on AP 2 still thinks that Client B - can be reached via swp0. It does not know that it has roamed to wlan0, - because it doesn't perform SA learning from the CPU port. - -Now Client A contacts Client B. -AP 1 routes the packet fine towards swp0 and delivers it on the Ethernet -segment. -AP 2 sees a frame on swp0 and its fdb says that the destination is swp0. -Hairpinning is disabled => drop. - -This problem comes from the fact that these switches have a 'blind spot' -for addresses coming from software bridging. The generic solution is not -to assume that hardware learning can be enabled somehow, but to listen -to more bridge learning events. It turns out that the bridge driver does -learn in software from all inbound frames, in __br_handle_local_finish. -A proper SWITCHDEV_FDB_ADD_TO_DEVICE notification is emitted for the -addresses serviced by the bridge on 'foreign' interfaces. The software -bridge also does the right thing on migration, by notifying that the old -entry is deleted, so that does not need to be special-cased in DSA. When -it is deleted, we just need to delete our static FDB entry towards the -CPU too, and wait. - -The problem is that DSA currently only cares about SWITCHDEV_FDB_ADD_TO_DEVICE -events received on its own interfaces, such as static FDB entries. - -Luckily we can change that, and DSA can listen to all switchdev FDB -add/del events in the system and figure out if those events were emitted -by a bridge that spans at least one of DSA's own ports. In case that is -true, DSA will also offload that address towards its own CPU port, in -the eventuality that there might be bridge clients attached to the DSA -switch who want to talk to the station connected to the foreign -interface. - -In terms of implementation, we need to keep the fdb_info->added_by_user -check for the case where the switchdev event was targeted directly at a -DSA switch port. But we don't need to look at that flag for snooped -events. So the check is currently too late, we need to move it earlier. -This also simplifies the code a bit, since we avoid uselessly allocating -and freeing switchdev_work. - -We could probably do some improvements in the future. For example, -multi-bridge support is rudimentary at the moment. If there are two -bridges spanning a DSA switch's ports, and both of them need to service -the same MAC address, then what will happen is that the migration of one -of those stations will trigger the deletion of the FDB entry from the -CPU port while it is still used by other bridge. That could be improved -with reference counting but is left for another time. - -This behavior needs to be enabled at driver level by setting -ds->assisted_learning_on_cpu_port = true. This is because we don't want -to inflict a potential performance penalty (accesses through -MDIO/I2C/SPI are expensive) to hardware that really doesn't need it -because address learning on the CPU port works there. - -Reported-by: DENG Qingfang -Signed-off-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Reviewed-by: Andrew Lunn -Signed-off-by: Jakub Kicinski ---- - include/net/dsa.h | 5 +++++ - net/dsa/slave.c | 66 +++++++++++++++++++++++++++++++++++++++++++++---------- - 2 files changed, 60 insertions(+), 11 deletions(-) - ---- a/include/net/dsa.h -+++ b/include/net/dsa.h -@@ -317,6 +317,11 @@ struct dsa_switch { - */ - bool untag_bridge_pvid; - -+ /* Let DSA manage the FDB entries towards the CPU, based on the -+ * software bridge database. -+ */ -+ bool assisted_learning_on_cpu_port; -+ - /* In case vlan_filtering_is_global is set, the VLAN awareness state - * should be retrieved from here and not from the per-port settings. - */ ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -2149,6 +2149,28 @@ static void dsa_slave_switchdev_event_wo - dev_put(dp->slave); - } - -+static int dsa_lower_dev_walk(struct net_device *lower_dev, -+ struct netdev_nested_priv *priv) -+{ -+ if (dsa_slave_dev_check(lower_dev)) { -+ priv->data = (void *)netdev_priv(lower_dev); -+ return 1; -+ } -+ -+ return 0; -+} -+ -+static struct dsa_slave_priv *dsa_slave_dev_lower_find(struct net_device *dev) -+{ -+ struct netdev_nested_priv priv = { -+ .data = NULL, -+ }; -+ -+ netdev_walk_all_lower_dev_rcu(dev, dsa_lower_dev_walk, &priv); -+ -+ return (struct dsa_slave_priv *)priv.data; -+} -+ - /* Called under rcu_read_lock() */ - static int dsa_slave_switchdev_event(struct notifier_block *unused, - unsigned long event, void *ptr) -@@ -2167,10 +2189,37 @@ static int dsa_slave_switchdev_event(str - return notifier_from_errno(err); - case SWITCHDEV_FDB_ADD_TO_DEVICE: - case SWITCHDEV_FDB_DEL_TO_DEVICE: -- if (!dsa_slave_dev_check(dev)) -- return NOTIFY_DONE; -+ fdb_info = ptr; -+ -+ if (dsa_slave_dev_check(dev)) { -+ if (!fdb_info->added_by_user) -+ return NOTIFY_OK; -+ -+ dp = dsa_slave_to_port(dev); -+ } else { -+ /* Snoop addresses learnt on foreign interfaces -+ * bridged with us, for switches that don't -+ * automatically learn SA from CPU-injected traffic -+ */ -+ struct net_device *br_dev; -+ struct dsa_slave_priv *p; -+ -+ br_dev = netdev_master_upper_dev_get_rcu(dev); -+ if (!br_dev) -+ return NOTIFY_DONE; -+ -+ if (!netif_is_bridge_master(br_dev)) -+ return NOTIFY_DONE; -+ -+ p = dsa_slave_dev_lower_find(br_dev); -+ if (!p) -+ return NOTIFY_DONE; - -- dp = dsa_slave_to_port(dev); -+ dp = p->dp->cpu_dp; -+ -+ if (!dp->ds->assisted_learning_on_cpu_port) -+ return NOTIFY_DONE; -+ } - - if (!dp->ds->ops->port_fdb_add || !dp->ds->ops->port_fdb_del) - return NOTIFY_DONE; -@@ -2185,18 +2234,13 @@ static int dsa_slave_switchdev_event(str - switchdev_work->port = dp->index; - switchdev_work->event = event; - -- fdb_info = ptr; -- -- if (!fdb_info->added_by_user) { -- kfree(switchdev_work); -- return NOTIFY_OK; -- } -- - ether_addr_copy(switchdev_work->addr, - fdb_info->addr); - switchdev_work->vid = fdb_info->vid; - -- dev_hold(dev); -+ /* Hold a reference on the slave for dsa_fdb_offload_notify */ -+ if (dsa_is_user_port(dp->ds, dp->index)) -+ dev_hold(dev); - dsa_schedule_work(&switchdev_work->work); - break; - default: diff --git a/target/linux/generic/backport-5.10/780-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch b/target/linux/generic/backport-5.10/780-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch deleted file mode 100644 index f3a6f948ad..0000000000 --- a/target/linux/generic/backport-5.10/780-net-dsa-mt7530-setup-core-clock-even-in-TRGMII-mode.patch +++ /dev/null @@ -1,84 +0,0 @@ -From c3b8e07909dbe67b0d580416c1a5257643a73be7 Mon Sep 17 00:00:00 2001 -From: Ilya Lipnitskiy -Date: Fri, 12 Mar 2021 00:07:03 -0800 -Subject: [PATCH] net: dsa: mt7530: setup core clock even in TRGMII mode - -A recent change to MIPS ralink reset logic made it so mt7530 actually -resets the switch on platforms such as mt7621 (where bit 2 is the reset -line for the switch). That exposed an issue where the switch would not -function properly in TRGMII mode after a reset. - -Reconfigure core clock in TRGMII mode to fix the issue. - -Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled. - -Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines") -Signed-off-by: Ilya Lipnitskiy -Signed-off-by: David S. Miller ---- - drivers/net/dsa/mt7530.c | 52 +++++++++++++++++++--------------------- - 1 file changed, 25 insertions(+), 27 deletions(-) - ---- a/drivers/net/dsa/mt7530.c -+++ b/drivers/net/dsa/mt7530.c -@@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch * - TD_DM_DRVP(8) | TD_DM_DRVN(8)); - - /* Setup core clock for MT7530 */ -- if (!trgint) { -- /* Disable MT7530 core clock */ -- core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); -- -- /* Disable PLL, since phy_device has not yet been created -- * provided for phy_[read,write]_mmd_indirect is called, we -- * provide our own core_write_mmd_indirect to complete this -- * function. -- */ -- core_write_mmd_indirect(priv, -- CORE_GSWPLL_GRP1, -- MDIO_MMD_VEND2, -- 0); -- -- /* Set core clock into 500Mhz */ -- core_write(priv, CORE_GSWPLL_GRP2, -- RG_GSWPLL_POSDIV_500M(1) | -- RG_GSWPLL_FBKDIV_500M(25)); -- -- /* Enable PLL */ -- core_write(priv, CORE_GSWPLL_GRP1, -- RG_GSWPLL_EN_PRE | -- RG_GSWPLL_POSDIV_200M(2) | -- RG_GSWPLL_FBKDIV_200M(32)); -- -- /* Enable MT7530 core clock */ -- core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); -- } -+ /* Disable MT7530 core clock */ -+ core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); -+ -+ /* Disable PLL, since phy_device has not yet been created -+ * provided for phy_[read,write]_mmd_indirect is called, we -+ * provide our own core_write_mmd_indirect to complete this -+ * function. -+ */ -+ core_write_mmd_indirect(priv, -+ CORE_GSWPLL_GRP1, -+ MDIO_MMD_VEND2, -+ 0); -+ -+ /* Set core clock into 500Mhz */ -+ core_write(priv, CORE_GSWPLL_GRP2, -+ RG_GSWPLL_POSDIV_500M(1) | -+ RG_GSWPLL_FBKDIV_500M(25)); -+ -+ /* Enable PLL */ -+ core_write(priv, CORE_GSWPLL_GRP1, -+ RG_GSWPLL_EN_PRE | -+ RG_GSWPLL_POSDIV_200M(2) | -+ RG_GSWPLL_FBKDIV_200M(32)); -+ -+ /* Enable MT7530 core clock */ -+ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); - - /* Setup the MT7530 TRGMII Tx Clock */ - core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); diff --git a/target/linux/generic/backport-5.10/781-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch b/target/linux/generic/backport-5.10/781-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch deleted file mode 100644 index 9e5047a16b..0000000000 --- a/target/linux/generic/backport-5.10/781-v5.12-net-dsa-mt7530-MT7530-optional-GPIO-support.patch +++ /dev/null @@ -1,181 +0,0 @@ -From 429a0edeefd88cbfca5c417dfb8561047bb50769 Mon Sep 17 00:00:00 2001 -From: DENG Qingfang -Date: Mon, 25 Jan 2021 12:43:22 +0800 -Subject: [PATCH] net: dsa: mt7530: MT7530 optional GPIO support - -MT7530's LED controller can drive up to 15 LED/GPIOs. - -Add support for GPIO control and allow users to use its GPIOs by -setting gpio-controller property in device tree. - -Signed-off-by: DENG Qingfang -Reviewed-by: Linus Walleij -Reviewed-by: Andrew Lunn -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/mt7530.c | 110 +++++++++++++++++++++++++++++++++++++++ - drivers/net/dsa/mt7530.h | 20 +++++++ - 2 files changed, 130 insertions(+) - ---- a/drivers/net/dsa/mt7530.c -+++ b/drivers/net/dsa/mt7530.c -@@ -18,6 +18,7 @@ - #include - #include - #include -+#include - #include - - #include "mt7530.h" -@@ -1534,6 +1535,109 @@ mtk_get_tag_protocol(struct dsa_switch * - } - } - -+static inline u32 -+mt7530_gpio_to_bit(unsigned int offset) -+{ -+ /* Map GPIO offset to register bit -+ * [ 2: 0] port 0 LED 0..2 as GPIO 0..2 -+ * [ 6: 4] port 1 LED 0..2 as GPIO 3..5 -+ * [10: 8] port 2 LED 0..2 as GPIO 6..8 -+ * [14:12] port 3 LED 0..2 as GPIO 9..11 -+ * [18:16] port 4 LED 0..2 as GPIO 12..14 -+ */ -+ return BIT(offset + offset / 3); -+} -+ -+static int -+mt7530_gpio_get(struct gpio_chip *gc, unsigned int offset) -+{ -+ struct mt7530_priv *priv = gpiochip_get_data(gc); -+ u32 bit = mt7530_gpio_to_bit(offset); -+ -+ return !!(mt7530_read(priv, MT7530_LED_GPIO_DATA) & bit); -+} -+ -+static void -+mt7530_gpio_set(struct gpio_chip *gc, unsigned int offset, int value) -+{ -+ struct mt7530_priv *priv = gpiochip_get_data(gc); -+ u32 bit = mt7530_gpio_to_bit(offset); -+ -+ if (value) -+ mt7530_set(priv, MT7530_LED_GPIO_DATA, bit); -+ else -+ mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit); -+} -+ -+static int -+mt7530_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) -+{ -+ struct mt7530_priv *priv = gpiochip_get_data(gc); -+ u32 bit = mt7530_gpio_to_bit(offset); -+ -+ return (mt7530_read(priv, MT7530_LED_GPIO_DIR) & bit) ? -+ GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN; -+} -+ -+static int -+mt7530_gpio_direction_input(struct gpio_chip *gc, unsigned int offset) -+{ -+ struct mt7530_priv *priv = gpiochip_get_data(gc); -+ u32 bit = mt7530_gpio_to_bit(offset); -+ -+ mt7530_clear(priv, MT7530_LED_GPIO_OE, bit); -+ mt7530_clear(priv, MT7530_LED_GPIO_DIR, bit); -+ -+ return 0; -+} -+ -+static int -+mt7530_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value) -+{ -+ struct mt7530_priv *priv = gpiochip_get_data(gc); -+ u32 bit = mt7530_gpio_to_bit(offset); -+ -+ mt7530_set(priv, MT7530_LED_GPIO_DIR, bit); -+ -+ if (value) -+ mt7530_set(priv, MT7530_LED_GPIO_DATA, bit); -+ else -+ mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit); -+ -+ mt7530_set(priv, MT7530_LED_GPIO_OE, bit); -+ -+ return 0; -+} -+ -+static int -+mt7530_setup_gpio(struct mt7530_priv *priv) -+{ -+ struct device *dev = priv->dev; -+ struct gpio_chip *gc; -+ -+ gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL); -+ if (!gc) -+ return -ENOMEM; -+ -+ mt7530_write(priv, MT7530_LED_GPIO_OE, 0); -+ mt7530_write(priv, MT7530_LED_GPIO_DIR, 0); -+ mt7530_write(priv, MT7530_LED_IO_MODE, 0); -+ -+ gc->label = "mt7530"; -+ gc->parent = dev; -+ gc->owner = THIS_MODULE; -+ gc->get_direction = mt7530_gpio_get_direction; -+ gc->direction_input = mt7530_gpio_direction_input; -+ gc->direction_output = mt7530_gpio_direction_output; -+ gc->get = mt7530_gpio_get; -+ gc->set = mt7530_gpio_set; -+ gc->base = -1; -+ gc->ngpio = 15; -+ gc->can_sleep = true; -+ -+ return devm_gpiochip_add_data(dev, gc, priv); -+} -+ - static int - mt7530_setup(struct dsa_switch *ds) - { -@@ -1675,6 +1779,12 @@ mt7530_setup(struct dsa_switch *ds) - } - } - -+ if (of_property_read_bool(priv->dev->of_node, "gpio-controller")) { -+ ret = mt7530_setup_gpio(priv); -+ if (ret) -+ return ret; -+ } -+ - mt7530_setup_port5(ds, interface); - - /* Flush the FDB table */ ---- a/drivers/net/dsa/mt7530.h -+++ b/drivers/net/dsa/mt7530.h -@@ -529,6 +529,26 @@ enum mt7531_clk_skew { - #define MT7531_GPIO12_RG_RXD3_MASK GENMASK(19, 16) - #define MT7531_EXT_P_MDIO_12 (2 << 16) - -+/* Registers for LED GPIO control (MT7530 only) -+ * All registers follow this pattern: -+ * [ 2: 0] port 0 -+ * [ 6: 4] port 1 -+ * [10: 8] port 2 -+ * [14:12] port 3 -+ * [18:16] port 4 -+ */ -+ -+/* LED enable, 0: Disable, 1: Enable (Default) */ -+#define MT7530_LED_EN 0x7d00 -+/* LED mode, 0: GPIO mode, 1: PHY mode (Default) */ -+#define MT7530_LED_IO_MODE 0x7d04 -+/* GPIO direction, 0: Input, 1: Output */ -+#define MT7530_LED_GPIO_DIR 0x7d10 -+/* GPIO output enable, 0: Disable, 1: Enable */ -+#define MT7530_LED_GPIO_OE 0x7d14 -+/* GPIO value, 0: Low, 1: High */ -+#define MT7530_LED_GPIO_DATA 0x7d18 -+ - #define MT7530_CREV 0x7ffc - #define CHIP_NAME_SHIFT 16 - #define MT7530_ID 0x7530 diff --git a/target/linux/generic/backport-5.10/781-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch b/target/linux/generic/backport-5.10/781-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch deleted file mode 100644 index 38dd8a7296..0000000000 --- a/target/linux/generic/backport-5.10/781-v5.13-net-dsa-mt7530-Add-support-for-EEE-features.patch +++ /dev/null @@ -1,120 +0,0 @@ -From 40b5d2f15c091fa9c854acde91ad2acb504027d7 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Ren=C3=A9=20van=20Dorst?= -Date: Mon, 12 Apr 2021 08:50:31 +0200 -Subject: [PATCH] net: dsa: mt7530: Add support for EEE features -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -This patch adds EEE support. - -Signed-off-by: René van Dorst -Signed-off-by: David S. Miller ---- - drivers/net/dsa/mt7530.c | 43 ++++++++++++++++++++++++++++++++++++++++ - drivers/net/dsa/mt7530.h | 14 ++++++++++++- - 2 files changed, 56 insertions(+), 1 deletion(-) - ---- a/drivers/net/dsa/mt7530.c -+++ b/drivers/net/dsa/mt7530.c -@@ -2371,6 +2371,17 @@ static void mt753x_phylink_mac_link_up(s - mcr |= PMCR_RX_FC_EN; - } - -+ if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, 0) >= 0) { -+ switch (speed) { -+ case SPEED_1000: -+ mcr |= PMCR_FORCE_EEE1G; -+ break; -+ case SPEED_100: -+ mcr |= PMCR_FORCE_EEE100; -+ break; -+ } -+ } -+ - mt7530_set(priv, MT7530_PMCR_P(port), mcr); - } - -@@ -2601,6 +2612,36 @@ mt753x_phy_write(struct dsa_switch *ds, - return priv->info->phy_write(ds, port, regnum, val); - } - -+static int mt753x_get_mac_eee(struct dsa_switch *ds, int port, -+ struct ethtool_eee *e) -+{ -+ struct mt7530_priv *priv = ds->priv; -+ u32 eeecr = mt7530_read(priv, MT7530_PMEEECR_P(port)); -+ -+ e->tx_lpi_enabled = !(eeecr & LPI_MODE_EN); -+ e->tx_lpi_timer = GET_LPI_THRESH(eeecr); -+ -+ return 0; -+} -+ -+static int mt753x_set_mac_eee(struct dsa_switch *ds, int port, -+ struct ethtool_eee *e) -+{ -+ struct mt7530_priv *priv = ds->priv; -+ u32 set, mask = LPI_THRESH_MASK | LPI_MODE_EN; -+ -+ if (e->tx_lpi_timer > 0xFFF) -+ return -EINVAL; -+ -+ set = SET_LPI_THRESH(e->tx_lpi_timer); -+ if (!e->tx_lpi_enabled) -+ /* Force LPI Mode without a delay */ -+ set |= LPI_MODE_EN; -+ mt7530_rmw(priv, MT7530_PMEEECR_P(port), mask, set); -+ -+ return 0; -+} -+ - static const struct dsa_switch_ops mt7530_switch_ops = { - .get_tag_protocol = mtk_get_tag_protocol, - .setup = mt753x_setup, -@@ -2629,6 +2670,8 @@ static const struct dsa_switch_ops mt753 - .phylink_mac_an_restart = mt753x_phylink_mac_an_restart, - .phylink_mac_link_down = mt753x_phylink_mac_link_down, - .phylink_mac_link_up = mt753x_phylink_mac_link_up, -+ .get_mac_eee = mt753x_get_mac_eee, -+ .set_mac_eee = mt753x_set_mac_eee, - }; - - static const struct mt753x_info mt753x_table[] = { ---- a/drivers/net/dsa/mt7530.h -+++ b/drivers/net/dsa/mt7530.h -@@ -240,6 +240,8 @@ enum mt7530_vlan_port_attr { - #define PMCR_RX_EN BIT(13) - #define PMCR_BACKOFF_EN BIT(9) - #define PMCR_BACKPR_EN BIT(8) -+#define PMCR_FORCE_EEE1G BIT(7) -+#define PMCR_FORCE_EEE100 BIT(6) - #define PMCR_TX_FC_EN BIT(5) - #define PMCR_RX_FC_EN BIT(4) - #define PMCR_FORCE_SPEED_1000 BIT(3) -@@ -264,7 +266,8 @@ enum mt7530_vlan_port_attr { - #define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \ - PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \ - PMCR_TX_FC_EN | PMCR_RX_FC_EN | \ -- PMCR_FORCE_FDX | PMCR_FORCE_LNK) -+ PMCR_FORCE_FDX | PMCR_FORCE_LNK | \ -+ PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100) - #define PMCR_CPU_PORT_SETTING(id) (PMCR_FORCE_MODE_ID((id)) | \ - PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \ - PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \ -@@ -273,6 +276,15 @@ enum mt7530_vlan_port_attr { - PMCR_FORCE_SPEED_1000 | \ - PMCR_FORCE_FDX | PMCR_FORCE_LNK) - -+#define MT7530_PMEEECR_P(x) (0x3004 + (x) * 0x100) -+#define WAKEUP_TIME_1000(x) (((x) & 0xFF) << 24) -+#define WAKEUP_TIME_100(x) (((x) & 0xFF) << 16) -+#define LPI_THRESH_MASK GENMASK(15, 4) -+#define LPI_THRESH_SHT 4 -+#define SET_LPI_THRESH(x) (((x) << LPI_THRESH_SHT) & LPI_THRESH_MASK) -+#define GET_LPI_THRESH(x) (((x) & LPI_THRESH_MASK) >> LPI_THRESH_SHT) -+#define LPI_MODE_EN BIT(0) -+ - #define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100) - #define PMSR_EEE1G BIT(7) - #define PMSR_EEE100M BIT(6) diff --git a/target/linux/generic/backport-5.10/782-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch b/target/linux/generic/backport-5.10/782-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch deleted file mode 100644 index 8e242bfffc..0000000000 --- a/target/linux/generic/backport-5.10/782-net-next-1-of-net-pass-the-dst-buffer-to-of_get_mac_address.patch +++ /dev/null @@ -1,1935 +0,0 @@ -From 83216e3988cd196183542937c9bd58b279f946af Mon Sep 17 00:00:00 2001 -From: Michael Walle -Date: Mon, 12 Apr 2021 19:47:17 +0200 -Subject: of: net: pass the dst buffer to of_get_mac_address() - -of_get_mac_address() returns a "const void*" pointer to a MAC address. -Lately, support to fetch the MAC address by an NVMEM provider was added. -But this will only work with platform devices. It will not work with -PCI devices (e.g. of an integrated root complex) and esp. not with DSA -ports. - -There is an of_* variant of the nvmem binding which works without -devices. The returned data of a nvmem_cell_read() has to be freed after -use. On the other hand the return of_get_mac_address() points to some -static data without a lifetime. The trick for now, was to allocate a -device resource managed buffer which is then returned. This will only -work if we have an actual device. - -Change it, so that the caller of of_get_mac_address() has to supply a -buffer where the MAC address is written to. Unfortunately, this will -touch all drivers which use the of_get_mac_address(). - -Usually the code looks like: - - const char *addr; - addr = of_get_mac_address(np); - if (!IS_ERR(addr)) - ether_addr_copy(ndev->dev_addr, addr); - -This can then be simply rewritten as: - - of_get_mac_address(np, ndev->dev_addr); - -Sometimes is_valid_ether_addr() is used to test the MAC address. -of_get_mac_address() already makes sure, it just returns a valid MAC -address. Thus we can just test its return code. But we have to be -careful if there are still other sources for the MAC address before the -of_get_mac_address(). In this case we have to keep the -is_valid_ether_addr() call. - -The following coccinelle patch was used to convert common cases to the -new style. Afterwards, I've manually gone over the drivers and fixed the -return code variable: either used a new one or if one was already -available use that. Mansour Moufid, thanks for that coccinelle patch! - - -@a@ -identifier x; -expression y, z; -@@ -- x = of_get_mac_address(y); -+ x = of_get_mac_address(y, z); - <... -- ether_addr_copy(z, x); - ...> - -@@ -identifier a.x; -@@ -- if (<+... x ...+>) {} - -@@ -identifier a.x; -@@ - if (<+... x ...+>) { - ... - } -- else {} - -@@ -identifier a.x; -expression e; -@@ -- if (<+... x ...+>@e) -- {} -- else -+ if (!(e)) - {...} - -@@ -expression x, y, z; -@@ -- x = of_get_mac_address(y, z); -+ of_get_mac_address(y, z); - ... when != x - - -All drivers, except drivers/net/ethernet/aeroflex/greth.c, were -compile-time tested. - -Suggested-by: Andrew Lunn -Signed-off-by: Michael Walle -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - arch/arm/mach-mvebu/kirkwood.c | 3 +- - arch/powerpc/sysdev/tsi108_dev.c | 5 +- - drivers/net/ethernet/aeroflex/greth.c | 6 +-- - drivers/net/ethernet/allwinner/sun4i-emac.c | 10 ++-- - drivers/net/ethernet/altera/altera_tse_main.c | 7 +-- - drivers/net/ethernet/arc/emac_main.c | 8 +-- - drivers/net/ethernet/atheros/ag71xx.c | 7 +-- - drivers/net/ethernet/broadcom/bcm4908_enet.c | 7 +-- - drivers/net/ethernet/broadcom/bcmsysport.c | 7 +-- - drivers/net/ethernet/broadcom/bgmac-bcma.c | 10 ++-- - drivers/net/ethernet/broadcom/bgmac-platform.c | 11 ++-- - drivers/net/ethernet/cadence/macb_main.c | 11 ++-- - drivers/net/ethernet/cavium/octeon/octeon_mgmt.c | 8 +-- - drivers/net/ethernet/cavium/thunder/thunder_bgx.c | 5 +- - drivers/net/ethernet/davicom/dm9000.c | 10 ++-- - drivers/net/ethernet/ethoc.c | 6 +-- - drivers/net/ethernet/ezchip/nps_enet.c | 7 +-- - drivers/net/ethernet/freescale/fec_main.c | 7 +-- - drivers/net/ethernet/freescale/fec_mpc52xx.c | 7 +-- - drivers/net/ethernet/freescale/fman/mac.c | 9 ++-- - .../net/ethernet/freescale/fs_enet/fs_enet-main.c | 5 +- - drivers/net/ethernet/freescale/gianfar.c | 8 +-- - drivers/net/ethernet/freescale/ucc_geth.c | 5 +- - drivers/net/ethernet/hisilicon/hisi_femac.c | 7 +-- - drivers/net/ethernet/hisilicon/hix5hd2_gmac.c | 7 +-- - drivers/net/ethernet/lantiq_xrx200.c | 7 +-- - drivers/net/ethernet/marvell/mv643xx_eth.c | 5 +- - drivers/net/ethernet/marvell/mvneta.c | 6 +-- - .../net/ethernet/marvell/prestera/prestera_main.c | 11 ++-- - drivers/net/ethernet/marvell/pxa168_eth.c | 9 +--- - drivers/net/ethernet/marvell/sky2.c | 8 ++- - drivers/net/ethernet/mediatek/mtk_eth_soc.c | 11 ++-- - drivers/net/ethernet/micrel/ks8851_common.c | 7 ++- - drivers/net/ethernet/microchip/lan743x_main.c | 5 +- - drivers/net/ethernet/nxp/lpc_eth.c | 4 +- - drivers/net/ethernet/qualcomm/qca_spi.c | 10 ++-- - drivers/net/ethernet/qualcomm/qca_uart.c | 9 +--- - drivers/net/ethernet/renesas/ravb_main.c | 12 +++-- - drivers/net/ethernet/renesas/sh_eth.c | 5 +- - .../net/ethernet/samsung/sxgbe/sxgbe_platform.c | 13 ++--- - drivers/net/ethernet/socionext/sni_ave.c | 10 ++-- - .../net/ethernet/stmicro/stmmac/dwmac-anarion.c | 2 +- - .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-generic.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-intel-plat.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 2 +- - .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c | 2 +- - .../net/ethernet/stmicro/stmmac/dwmac-visconti.c | 2 +- - drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 +- - drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- - .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 14 ++--- - .../net/ethernet/stmicro/stmmac/stmmac_platform.h | 2 +- - drivers/net/ethernet/ti/am65-cpsw-nuss.c | 19 ++++--- - drivers/net/ethernet/ti/cpsw.c | 7 +-- - drivers/net/ethernet/ti/cpsw_new.c | 7 +-- - drivers/net/ethernet/ti/davinci_emac.c | 8 +-- - drivers/net/ethernet/ti/netcp_core.c | 7 +-- - drivers/net/ethernet/wiznet/w5100-spi.c | 8 ++- - drivers/net/ethernet/wiznet/w5100.c | 2 +- - drivers/net/ethernet/xilinx/ll_temac_main.c | 8 +-- - drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 15 +++--- - drivers/net/ethernet/xilinx/xilinx_emaclite.c | 8 +-- - drivers/net/wireless/ath/ath9k/init.c | 5 +- - drivers/net/wireless/mediatek/mt76/eeprom.c | 9 +--- - drivers/net/wireless/ralink/rt2x00/rt2x00dev.c | 6 +-- - drivers/of/of_net.c | 60 ++++++++++------------ - drivers/staging/octeon/ethernet.c | 10 ++-- - drivers/staging/wfx/main.c | 7 ++- - include/linux/of_net.h | 6 +-- - include/net/dsa.h | 2 +- - net/dsa/dsa2.c | 2 +- - net/dsa/slave.c | 2 +- - net/ethernet/eth.c | 11 ++-- - 85 files changed, 218 insertions(+), 364 deletions(-) - ---- a/arch/arm/mach-mvebu/kirkwood.c -+++ b/arch/arm/mach-mvebu/kirkwood.c -@@ -84,6 +84,7 @@ static void __init kirkwood_dt_eth_fixup - struct device_node *pnp = of_get_parent(np); - struct clk *clk; - struct property *pmac; -+ u8 tmpmac[ETH_ALEN]; - void __iomem *io; - u8 *macaddr; - u32 reg; -@@ -93,7 +94,7 @@ static void __init kirkwood_dt_eth_fixup - - /* skip disabled nodes or nodes with valid MAC address*/ - if (!of_device_is_available(pnp) || -- !IS_ERR(of_get_mac_address(np))) -+ !of_get_mac_address(np, tmpmac)) - goto eth_fixup_skip; - - clk = of_clk_get(pnp, 0); ---- a/arch/powerpc/sysdev/tsi108_dev.c -+++ b/arch/powerpc/sysdev/tsi108_dev.c -@@ -73,7 +73,6 @@ static int __init tsi108_eth_of_init(voi - struct device_node *phy, *mdio; - hw_info tsi_eth_data; - const unsigned int *phy_id; -- const void *mac_addr; - const phandle *ph; - - memset(r, 0, sizeof(r)); -@@ -101,9 +100,7 @@ static int __init tsi108_eth_of_init(voi - goto err; - } - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(tsi_eth_data.mac_addr, mac_addr); -+ of_get_mac_address(np, tsi_eth_data.mac_addr); - - ph = of_get_property(np, "mdio-handle", NULL); - mdio = of_find_node_by_phandle(*ph); ---- a/drivers/net/ethernet/aeroflex/greth.c -+++ b/drivers/net/ethernet/aeroflex/greth.c -@@ -1449,10 +1449,10 @@ static int greth_of_probe(struct platfor - break; - } - if (i == 6) { -- const u8 *addr; -+ u8 addr[ETH_ALEN]; - -- addr = of_get_mac_address(ofdev->dev.of_node); -- if (!IS_ERR(addr)) { -+ err = of_get_mac_address(ofdev->dev.of_node, addr); -+ if (!err) { - for (i = 0; i < 6; i++) - macaddr[i] = (unsigned int) addr[i]; - } else { ---- a/drivers/net/ethernet/allwinner/sun4i-emac.c -+++ b/drivers/net/ethernet/allwinner/sun4i-emac.c -@@ -790,7 +790,6 @@ static int emac_probe(struct platform_de - struct emac_board_info *db; - struct net_device *ndev; - int ret = 0; -- const char *mac_addr; - - ndev = alloc_etherdev(sizeof(struct emac_board_info)); - if (!ndev) { -@@ -853,12 +852,9 @@ static int emac_probe(struct platform_de - } - - /* Read MAC-address from DT */ -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- -- /* Check if the MAC address is valid, if not get a random one */ -- if (!is_valid_ether_addr(ndev->dev_addr)) { -+ ret = of_get_mac_address(np, ndev->dev_addr); -+ if (ret) { -+ /* if the MAC address is invalid get a random one */ - eth_hw_addr_random(ndev); - dev_warn(&pdev->dev, "using random MAC address %pM\n", - ndev->dev_addr); ---- a/drivers/net/ethernet/altera/altera_tse_main.c -+++ b/drivers/net/ethernet/altera/altera_tse_main.c -@@ -1351,7 +1351,6 @@ static int altera_tse_probe(struct platf - struct resource *control_port; - struct resource *dma_res; - struct altera_tse_private *priv; -- const unsigned char *macaddr; - void __iomem *descmap; - const struct of_device_id *of_id = NULL; - -@@ -1525,10 +1524,8 @@ static int altera_tse_probe(struct platf - priv->rx_dma_buf_sz = ALTERA_RXDMABUFFER_SIZE; - - /* get default MAC address from device tree */ -- macaddr = of_get_mac_address(pdev->dev.of_node); -- if (!IS_ERR(macaddr)) -- ether_addr_copy(ndev->dev_addr, macaddr); -- else -+ ret = of_get_mac_address(pdev->dev.of_node, ndev->dev_addr); -+ if (ret) - eth_hw_addr_random(ndev); - - /* get phy addr and create mdio */ ---- a/drivers/net/ethernet/arc/emac_main.c -+++ b/drivers/net/ethernet/arc/emac_main.c -@@ -857,7 +857,6 @@ int arc_emac_probe(struct net_device *nd - struct device_node *phy_node; - struct phy_device *phydev = NULL; - struct arc_emac_priv *priv; -- const char *mac_addr; - unsigned int id, clock_frequency, irq; - int err; - -@@ -942,11 +941,8 @@ int arc_emac_probe(struct net_device *nd - } - - /* Get MAC address from device tree */ -- mac_addr = of_get_mac_address(dev->of_node); -- -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- else -+ err = of_get_mac_address(dev->of_node, ndev->dev_addr); -+ if (err) - eth_hw_addr_random(ndev); - - arc_emac_set_address_internal(ndev); ---- a/drivers/net/ethernet/atheros/ag71xx.c -+++ b/drivers/net/ethernet/atheros/ag71xx.c -@@ -1856,7 +1856,6 @@ static int ag71xx_probe(struct platform_ - const struct ag71xx_dcfg *dcfg; - struct net_device *ndev; - struct resource *res; -- const void *mac_addr; - int tx_size, err, i; - struct ag71xx *ag; - -@@ -1957,10 +1956,8 @@ static int ag71xx_probe(struct platform_ - ag->stop_desc->ctrl = 0; - ag->stop_desc->next = (u32)ag->stop_desc_dma; - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- memcpy(ndev->dev_addr, mac_addr, ETH_ALEN); -- if (IS_ERR(mac_addr) || !is_valid_ether_addr(ndev->dev_addr)) { -+ err = of_get_mac_address(np, ndev->dev_addr); -+ if (err) { - netif_err(ag, probe, ndev, "invalid MAC address, using random address\n"); - eth_random_addr(ndev->dev_addr); - } ---- a/drivers/net/ethernet/broadcom/bcmsysport.c -+++ b/drivers/net/ethernet/broadcom/bcmsysport.c -@@ -2465,7 +2465,6 @@ static int bcm_sysport_probe(struct plat - struct bcm_sysport_priv *priv; - struct device_node *dn; - struct net_device *dev; -- const void *macaddr; - u32 txq, rxq; - int ret; - -@@ -2560,12 +2559,10 @@ static int bcm_sysport_probe(struct plat - } - - /* Initialize netdevice members */ -- macaddr = of_get_mac_address(dn); -- if (IS_ERR(macaddr)) { -+ ret = of_get_mac_address(dn, dev->dev_addr); -+ if (ret) { - dev_warn(&pdev->dev, "using random Ethernet MAC\n"); - eth_hw_addr_random(dev); -- } else { -- ether_addr_copy(dev->dev_addr, macaddr); - } - - SET_NETDEV_DEV(dev, &pdev->dev); ---- a/drivers/net/ethernet/broadcom/bgmac-bcma.c -+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c -@@ -115,7 +115,7 @@ static int bgmac_probe(struct bcma_devic - struct ssb_sprom *sprom = &core->bus->sprom; - struct mii_bus *mii_bus; - struct bgmac *bgmac; -- const u8 *mac = NULL; -+ const u8 *mac; - int err; - - bgmac = bgmac_alloc(&core->dev); -@@ -128,11 +128,10 @@ static int bgmac_probe(struct bcma_devic - - bcma_set_drvdata(core, bgmac); - -- if (bgmac->dev->of_node) -- mac = of_get_mac_address(bgmac->dev->of_node); -+ err = of_get_mac_address(bgmac->dev->of_node, bgmac->net_dev->dev_addr); - - /* If no MAC address assigned via device tree, check SPROM */ -- if (IS_ERR_OR_NULL(mac)) { -+ if (err) { - switch (core->core_unit) { - case 0: - mac = sprom->et0mac; -@@ -149,10 +148,9 @@ static int bgmac_probe(struct bcma_devic - err = -ENOTSUPP; - goto err; - } -+ ether_addr_copy(bgmac->net_dev->dev_addr, mac); - } - -- ether_addr_copy(bgmac->net_dev->dev_addr, mac); -- - /* On BCM4706 we need common core to access PHY */ - if (core->id.id == BCMA_CORE_4706_MAC_GBIT && - !core->bus->drv_gmac_cmn.core) { ---- a/drivers/net/ethernet/broadcom/bgmac-platform.c -+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c -@@ -173,7 +173,7 @@ static int bgmac_probe(struct platform_d - struct device_node *np = pdev->dev.of_node; - struct bgmac *bgmac; - struct resource *regs; -- const u8 *mac_addr; -+ int ret; - - bgmac = bgmac_alloc(&pdev->dev); - if (!bgmac) -@@ -192,11 +192,10 @@ static int bgmac_probe(struct platform_d - bgmac->dev = &pdev->dev; - bgmac->dma_dev = &pdev->dev; - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(bgmac->net_dev->dev_addr, mac_addr); -- else -- dev_warn(&pdev->dev, "MAC address not present in device tree\n"); -+ ret = of_get_mac_address(np, bgmac->net_dev->dev_addr); -+ if (ret) -+ dev_warn(&pdev->dev, -+ "MAC address not present in device tree\n"); - - bgmac->irq = platform_get_irq(pdev, 0); - if (bgmac->irq < 0) ---- a/drivers/net/ethernet/cadence/macb_main.c -+++ b/drivers/net/ethernet/cadence/macb_main.c -@@ -4456,7 +4456,6 @@ static int macb_probe(struct platform_de - struct net_device *dev; - struct resource *regs; - void __iomem *mem; -- const char *mac; - struct macb *bp; - int err, val; - -@@ -4569,15 +4568,11 @@ static int macb_probe(struct platform_de - if (bp->caps & MACB_CAPS_NEEDS_RSTONUBR) - bp->rx_intr_mask |= MACB_BIT(RXUBR); - -- mac = of_get_mac_address(np); -- if (PTR_ERR(mac) == -EPROBE_DEFER) { -- err = -EPROBE_DEFER; -+ err = of_get_mac_address(np, bp->dev->dev_addr); -+ if (err == -EPROBE_DEFER) - goto err_out_free_netdev; -- } else if (!IS_ERR_OR_NULL(mac)) { -- ether_addr_copy(bp->dev->dev_addr, mac); -- } else { -+ else if (err) - macb_get_hwaddr(bp); -- } - - err = of_get_phy_mode(np, &interface); - if (err) ---- a/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c -+++ b/drivers/net/ethernet/cavium/octeon/octeon_mgmt.c -@@ -1385,7 +1385,6 @@ static int octeon_mgmt_probe(struct plat - struct net_device *netdev; - struct octeon_mgmt *p; - const __be32 *data; -- const u8 *mac; - struct resource *res_mix; - struct resource *res_agl; - struct resource *res_agl_prt_ctl; -@@ -1502,11 +1501,8 @@ static int octeon_mgmt_probe(struct plat - netdev->min_mtu = 64 - OCTEON_MGMT_RX_HEADROOM; - netdev->max_mtu = 16383 - OCTEON_MGMT_RX_HEADROOM - VLAN_HLEN; - -- mac = of_get_mac_address(pdev->dev.of_node); -- -- if (!IS_ERR(mac)) -- ether_addr_copy(netdev->dev_addr, mac); -- else -+ result = of_get_mac_address(pdev->dev.of_node, netdev->dev_addr); -+ if (result) - eth_hw_addr_random(netdev); - - p->phy_np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0); ---- a/drivers/net/ethernet/cavium/thunder/thunder_bgx.c -+++ b/drivers/net/ethernet/cavium/thunder/thunder_bgx.c -@@ -1474,7 +1474,6 @@ static int bgx_init_of_phy(struct bgx *b - device_for_each_child_node(&bgx->pdev->dev, fwn) { - struct phy_device *pd; - struct device_node *phy_np; -- const char *mac; - - /* Should always be an OF node. But if it is not, we - * cannot handle it, so exit the loop. -@@ -1483,9 +1482,7 @@ static int bgx_init_of_phy(struct bgx *b - if (!node) - break; - -- mac = of_get_mac_address(node); -- if (!IS_ERR(mac)) -- ether_addr_copy(bgx->lmac[lmac].mac, mac); -+ of_get_mac_address(node, bgx->lmac[lmac].mac); - - SET_NETDEV_DEV(&bgx->lmac[lmac].netdev, &bgx->pdev->dev); - bgx->lmac[lmac].lmacid = lmac; ---- a/drivers/net/ethernet/davicom/dm9000.c -+++ b/drivers/net/ethernet/davicom/dm9000.c -@@ -1388,7 +1388,7 @@ static struct dm9000_plat_data *dm9000_p - { - struct dm9000_plat_data *pdata; - struct device_node *np = dev->of_node; -- const void *mac_addr; -+ int ret; - - if (!IS_ENABLED(CONFIG_OF) || !np) - return ERR_PTR(-ENXIO); -@@ -1402,11 +1402,9 @@ static struct dm9000_plat_data *dm9000_p - if (of_find_property(np, "davicom,no-eeprom", NULL)) - pdata->flags |= DM9000_PLATF_NO_EEPROM; - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(pdata->dev_addr, mac_addr); -- else if (PTR_ERR(mac_addr) == -EPROBE_DEFER) -- return ERR_CAST(mac_addr); -+ ret = of_get_mac_address(np, pdata->dev_addr); -+ if (ret == -EPROBE_DEFER) -+ return ERR_PTR(ret); - - return pdata; - } ---- a/drivers/net/ethernet/ethoc.c -+++ b/drivers/net/ethernet/ethoc.c -@@ -1151,11 +1151,7 @@ static int ethoc_probe(struct platform_d - ether_addr_copy(netdev->dev_addr, pdata->hwaddr); - priv->phy_id = pdata->phy_id; - } else { -- const void *mac; -- -- mac = of_get_mac_address(pdev->dev.of_node); -- if (!IS_ERR(mac)) -- ether_addr_copy(netdev->dev_addr, mac); -+ of_get_mac_address(pdev->dev.of_node, netdev->dev_addr); - priv->phy_id = -1; - } - ---- a/drivers/net/ethernet/ezchip/nps_enet.c -+++ b/drivers/net/ethernet/ezchip/nps_enet.c -@@ -575,7 +575,6 @@ static s32 nps_enet_probe(struct platfor - struct net_device *ndev; - struct nps_enet_priv *priv; - s32 err = 0; -- const char *mac_addr; - - if (!dev->of_node) - return -ENODEV; -@@ -602,10 +601,8 @@ static s32 nps_enet_probe(struct platfor - dev_dbg(dev, "Registers base address is 0x%p\n", priv->regs_base); - - /* set kernel MAC address to dev */ -- mac_addr = of_get_mac_address(dev->of_node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- else -+ err = of_get_mac_address(dev->of_node, ndev->dev_addr); -+ if (err) - eth_hw_addr_random(ndev); - - /* Get IRQ number */ ---- a/drivers/net/ethernet/freescale/fec_main.c -+++ b/drivers/net/ethernet/freescale/fec_main.c -@@ -1666,6 +1666,7 @@ static void fec_get_mac(struct net_devic - struct fec_enet_private *fep = netdev_priv(ndev); - struct fec_platform_data *pdata = dev_get_platdata(&fep->pdev->dev); - unsigned char *iap, tmpaddr[ETH_ALEN]; -+ int ret; - - /* - * try to get mac address in following order: -@@ -1681,9 +1682,9 @@ static void fec_get_mac(struct net_devic - if (!is_valid_ether_addr(iap)) { - struct device_node *np = fep->pdev->dev.of_node; - if (np) { -- const char *mac = of_get_mac_address(np); -- if (!IS_ERR(mac)) -- iap = (unsigned char *) mac; -+ ret = of_get_mac_address(np, tmpaddr); -+ if (!ret) -+ iap = tmpaddr; - } - } - ---- a/drivers/net/ethernet/freescale/fec_mpc52xx.c -+++ b/drivers/net/ethernet/freescale/fec_mpc52xx.c -@@ -813,7 +813,6 @@ static int mpc52xx_fec_probe(struct plat - const u32 *prop; - int prop_size; - struct device_node *np = op->dev.of_node; -- const char *mac_addr; - - phys_addr_t rx_fifo; - phys_addr_t tx_fifo; -@@ -891,10 +890,8 @@ static int mpc52xx_fec_probe(struct plat - * - * First try to read MAC address from DT - */ -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(ndev->dev_addr, mac_addr); -- } else { -+ rv = of_get_mac_address(np, ndev->dev_addr); -+ if (rv) { - struct mpc52xx_fec __iomem *fec = priv->fec; - - /* ---- a/drivers/net/ethernet/freescale/fman/mac.c -+++ b/drivers/net/ethernet/freescale/fman/mac.c -@@ -605,7 +605,6 @@ static int mac_probe(struct platform_dev - struct platform_device *of_dev; - struct resource res; - struct mac_priv_s *priv; -- const u8 *mac_addr; - u32 val; - u8 fman_id; - phy_interface_t phy_if; -@@ -723,11 +722,9 @@ static int mac_probe(struct platform_dev - priv->cell_index = (u8)val; - - /* Get the MAC address */ -- mac_addr = of_get_mac_address(mac_node); -- if (IS_ERR(mac_addr)) -+ err = of_get_mac_address(mac_node, mac_dev->addr); -+ if (err) - dev_warn(dev, "of_get_mac_address(%pOF) failed\n", mac_node); -- else -- ether_addr_copy(mac_dev->addr, mac_addr); - - /* Get the port handles */ - nph = of_count_phandle_with_args(mac_node, "fsl,fman-ports", NULL); -@@ -853,7 +850,7 @@ static int mac_probe(struct platform_dev - if (err < 0) - dev_err(dev, "fman_set_mac_active_pause() = %d\n", err); - -- if (!IS_ERR(mac_addr)) -+ if (!is_zero_ether_addr(mac_dev->addr)) - dev_info(dev, "FMan MAC address: %pM\n", mac_dev->addr); - - priv->eth_dev = dpaa_eth_add_device(fman_id, mac_dev); ---- a/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c -+++ b/drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c -@@ -918,7 +918,6 @@ static int fs_enet_probe(struct platform - const u32 *data; - struct clk *clk; - int err; -- const u8 *mac_addr; - const char *phy_connection_type; - int privsize, len, ret = -ENODEV; - -@@ -1006,9 +1005,7 @@ static int fs_enet_probe(struct platform - spin_lock_init(&fep->lock); - spin_lock_init(&fep->tx_lock); - -- mac_addr = of_get_mac_address(ofdev->dev.of_node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -+ of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr); - - ret = fep->ops->allocate_bd(ndev); - if (ret) ---- a/drivers/net/ethernet/freescale/gianfar.c -+++ b/drivers/net/ethernet/freescale/gianfar.c -@@ -641,7 +641,6 @@ static phy_interface_t gfar_get_interfac - static int gfar_of_init(struct platform_device *ofdev, struct net_device **pdev) - { - const char *model; -- const void *mac_addr; - int err = 0, i; - phy_interface_t interface; - struct net_device *dev = NULL; -@@ -783,11 +782,8 @@ static int gfar_of_init(struct platform_ - if (stash_len || stash_idx) - priv->device_flags |= FSL_GIANFAR_DEV_HAS_BUF_STASHING; - -- mac_addr = of_get_mac_address(np); -- -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(dev->dev_addr, mac_addr); -- } else { -+ err = of_get_mac_address(np, dev->dev_addr); -+ if (err) { - eth_hw_addr_random(dev); - dev_info(&ofdev->dev, "Using random MAC address: %pM\n", dev->dev_addr); - } ---- a/drivers/net/ethernet/freescale/ucc_geth.c -+++ b/drivers/net/ethernet/freescale/ucc_geth.c -@@ -3696,7 +3696,6 @@ static int ucc_geth_probe(struct platfor - int err, ucc_num, max_speed = 0; - const unsigned int *prop; - const char *sprop; -- const void *mac_addr; - phy_interface_t phy_interface; - static const int enet_to_speed[] = { - SPEED_10, SPEED_10, SPEED_10, -@@ -3906,9 +3905,7 @@ static int ucc_geth_probe(struct platfor - goto err_free_netdev; - } - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(dev->dev_addr, mac_addr); -+ of_get_mac_address(np, dev->dev_addr); - - ugeth->ug_info = ug_info; - ugeth->dev = device; ---- a/drivers/net/ethernet/hisilicon/hisi_femac.c -+++ b/drivers/net/ethernet/hisilicon/hisi_femac.c -@@ -772,7 +772,6 @@ static int hisi_femac_drv_probe(struct p - struct net_device *ndev; - struct hisi_femac_priv *priv; - struct phy_device *phy; -- const char *mac_addr; - int ret; - - ndev = alloc_etherdev(sizeof(*priv)); -@@ -842,10 +841,8 @@ static int hisi_femac_drv_probe(struct p - (unsigned long)phy->phy_id, - phy_modes(phy->interface)); - -- mac_addr = of_get_mac_address(node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- if (!is_valid_ether_addr(ndev->dev_addr)) { -+ ret = of_get_mac_address(node, ndev->dev_addr); -+ if (ret) { - eth_hw_addr_random(ndev); - dev_warn(dev, "using random MAC address %pM\n", - ndev->dev_addr); ---- a/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c -+++ b/drivers/net/ethernet/hisilicon/hix5hd2_gmac.c -@@ -1098,7 +1098,6 @@ static int hix5hd2_dev_probe(struct plat - struct net_device *ndev; - struct hix5hd2_priv *priv; - struct mii_bus *bus; -- const char *mac_addr; - int ret; - - ndev = alloc_etherdev(sizeof(struct hix5hd2_priv)); -@@ -1220,10 +1219,8 @@ static int hix5hd2_dev_probe(struct plat - goto out_phy_node; - } - -- mac_addr = of_get_mac_address(node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- if (!is_valid_ether_addr(ndev->dev_addr)) { -+ ret = of_get_mac_address(node, ndev->dev_addr); -+ if (ret) { - eth_hw_addr_random(ndev); - netdev_warn(ndev, "using random MAC address %pM\n", - ndev->dev_addr); ---- a/drivers/net/ethernet/lantiq_xrx200.c -+++ b/drivers/net/ethernet/lantiq_xrx200.c -@@ -440,7 +440,6 @@ static int xrx200_probe(struct platform_ - struct resource *res; - struct xrx200_priv *priv; - struct net_device *net_dev; -- const u8 *mac; - int err; - - /* alloc the network device */ -@@ -484,10 +483,8 @@ static int xrx200_probe(struct platform_ - return PTR_ERR(priv->clk); - } - -- mac = of_get_mac_address(np); -- if (!IS_ERR(mac)) -- ether_addr_copy(net_dev->dev_addr, mac); -- else -+ err = of_get_mac_address(np, net_dev->dev_addr); -+ if (err) - eth_hw_addr_random(net_dev); - - /* bring up the dma engine and IP core */ ---- a/drivers/net/ethernet/marvell/mv643xx_eth.c -+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c -@@ -2700,7 +2700,6 @@ static int mv643xx_eth_shared_of_add_por - struct platform_device *ppdev; - struct mv643xx_eth_platform_data ppd; - struct resource res; -- const char *mac_addr; - int ret; - int dev_num = 0; - -@@ -2731,9 +2730,7 @@ static int mv643xx_eth_shared_of_add_por - return -EINVAL; - } - -- mac_addr = of_get_mac_address(pnp); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ppd.mac_addr, mac_addr); -+ of_get_mac_address(pnp, ppd.mac_addr); - - mv643xx_eth_property(pnp, "tx-queue-size", ppd.tx_queue_size); - mv643xx_eth_property(pnp, "tx-sram-addr", ppd.tx_sram_addr); ---- a/drivers/net/ethernet/marvell/mvneta.c -+++ b/drivers/net/ethernet/marvell/mvneta.c -@@ -5062,7 +5062,6 @@ static int mvneta_probe(struct platform_ - struct net_device *dev; - struct phylink *phylink; - struct phy *comphy; -- const char *dt_mac_addr; - char hw_mac_addr[ETH_ALEN]; - phy_interface_t phy_mode; - const char *mac_from; -@@ -5158,10 +5157,9 @@ static int mvneta_probe(struct platform_ - goto err_free_ports; - } - -- dt_mac_addr = of_get_mac_address(dn); -- if (!IS_ERR(dt_mac_addr)) { -+ err = of_get_mac_address(dn, dev->dev_addr); -+ if (!err) { - mac_from = "device tree"; -- ether_addr_copy(dev->dev_addr, dt_mac_addr); - } else { - mvneta_get_mac_addr(pp, hw_mac_addr); - if (is_valid_ether_addr(hw_mac_addr)) { ---- a/drivers/net/ethernet/marvell/prestera/prestera_main.c -+++ b/drivers/net/ethernet/marvell/prestera/prestera_main.c -@@ -462,20 +462,17 @@ static int prestera_switch_set_base_mac_ - { - struct device_node *base_mac_np; - struct device_node *np; -- const char *base_mac; -+ int ret; - - np = of_find_compatible_node(NULL, NULL, "marvell,prestera"); - base_mac_np = of_parse_phandle(np, "base-mac-provider", 0); - -- base_mac = of_get_mac_address(base_mac_np); -- of_node_put(base_mac_np); -- if (!IS_ERR(base_mac)) -- ether_addr_copy(sw->base_mac, base_mac); -- -- if (!is_valid_ether_addr(sw->base_mac)) { -+ ret = of_get_mac_address(base_mac_np, sw->base_mac); -+ if (ret) { - eth_random_addr(sw->base_mac); - dev_info(prestera_dev(sw), "using random base mac address\n"); - } -+ of_node_put(base_mac_np); - - return prestera_hw_switch_mac_set(sw, sw->base_mac); - } ---- a/drivers/net/ethernet/marvell/pxa168_eth.c -+++ b/drivers/net/ethernet/marvell/pxa168_eth.c -@@ -1392,7 +1392,6 @@ static int pxa168_eth_probe(struct platf - struct resource *res; - struct clk *clk; - struct device_node *np; -- const unsigned char *mac_addr = NULL; - int err; - - printk(KERN_NOTICE "PXA168 10/100 Ethernet Driver\n"); -@@ -1435,12 +1434,8 @@ static int pxa168_eth_probe(struct platf - - INIT_WORK(&pep->tx_timeout_task, pxa168_eth_tx_timeout_task); - -- if (pdev->dev.of_node) -- mac_addr = of_get_mac_address(pdev->dev.of_node); -- -- if (!IS_ERR_OR_NULL(mac_addr)) { -- ether_addr_copy(dev->dev_addr, mac_addr); -- } else { -+ err = of_get_mac_address(pdev->dev.of_node, dev->dev_addr); -+ if (err) { - /* try reading the mac address, if set by the bootloader */ - pxa168_eth_get_mac_address(dev, dev->dev_addr); - if (!is_valid_ether_addr(dev->dev_addr)) { ---- a/drivers/net/ethernet/marvell/sky2.c -+++ b/drivers/net/ethernet/marvell/sky2.c -@@ -4725,7 +4725,7 @@ static struct net_device *sky2_init_netd - { - struct sky2_port *sky2; - struct net_device *dev = alloc_etherdev(sizeof(*sky2)); -- const void *iap; -+ int ret; - - if (!dev) - return NULL; -@@ -4795,10 +4795,8 @@ static struct net_device *sky2_init_netd - * 1) from device tree data - * 2) from internal registers set by bootloader - */ -- iap = of_get_mac_address(hw->pdev->dev.of_node); -- if (!IS_ERR(iap)) -- ether_addr_copy(dev->dev_addr, iap); -- else -+ ret = of_get_mac_address(hw->pdev->dev.of_node, dev->dev_addr); -+ if (ret) - memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, - ETH_ALEN); - ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c -@@ -2580,14 +2580,11 @@ static int __init mtk_init(struct net_de - { - struct mtk_mac *mac = netdev_priv(dev); - struct mtk_eth *eth = mac->hw; -- const char *mac_addr; -+ int ret; - -- mac_addr = of_get_mac_address(mac->of_node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(dev->dev_addr, mac_addr); -- -- /* If the mac address is invalid, use random mac address */ -- if (!is_valid_ether_addr(dev->dev_addr)) { -+ ret = of_get_mac_address(mac->of_node, dev->dev_addr); -+ if (ret) { -+ /* If the mac address is invalid, use random mac address */ - eth_hw_addr_random(dev); - dev_err(eth->dev, "generated random MAC address %pM\n", - dev->dev_addr); ---- a/drivers/net/ethernet/micrel/ks8851_common.c -+++ b/drivers/net/ethernet/micrel/ks8851_common.c -@@ -194,11 +194,10 @@ static void ks8851_read_mac_addr(struct - static void ks8851_init_mac(struct ks8851_net *ks, struct device_node *np) - { - struct net_device *dev = ks->netdev; -- const u8 *mac_addr; -+ int ret; - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(dev->dev_addr, mac_addr); -+ ret = of_get_mac_address(np, dev->dev_addr); -+ if (!ret) { - ks8851_write_mac_addr(dev); - return; - } ---- a/drivers/net/ethernet/microchip/lan743x_main.c -+++ b/drivers/net/ethernet/microchip/lan743x_main.c -@@ -2835,7 +2835,6 @@ static int lan743x_pcidev_probe(struct p - { - struct lan743x_adapter *adapter = NULL; - struct net_device *netdev = NULL; -- const void *mac_addr; - int ret = -ENODEV; - - netdev = devm_alloc_etherdev(&pdev->dev, -@@ -2852,9 +2851,7 @@ static int lan743x_pcidev_probe(struct p - NETIF_MSG_IFDOWN | NETIF_MSG_TX_QUEUED; - netdev->max_mtu = LAN743X_MAX_FRAME_SIZE; - -- mac_addr = of_get_mac_address(pdev->dev.of_node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(adapter->mac_address, mac_addr); -+ of_get_mac_address(pdev->dev.of_node, adapter->mac_address); - - ret = lan743x_pci_init(adapter, pdev); - if (ret) ---- a/drivers/net/ethernet/nxp/lpc_eth.c -+++ b/drivers/net/ethernet/nxp/lpc_eth.c -@@ -1347,9 +1347,7 @@ static int lpc_eth_drv_probe(struct plat - __lpc_get_mac(pldat, ndev->dev_addr); - - if (!is_valid_ether_addr(ndev->dev_addr)) { -- const char *macaddr = of_get_mac_address(np); -- if (!IS_ERR(macaddr)) -- ether_addr_copy(ndev->dev_addr, macaddr); -+ of_get_mac_address(np, ndev->dev_addr); - } - if (!is_valid_ether_addr(ndev->dev_addr)) - eth_hw_addr_random(ndev); ---- a/drivers/net/ethernet/qualcomm/qca_spi.c -+++ b/drivers/net/ethernet/qualcomm/qca_spi.c -@@ -885,7 +885,7 @@ qca_spi_probe(struct spi_device *spi) - struct net_device *qcaspi_devs = NULL; - u8 legacy_mode = 0; - u16 signature; -- const char *mac; -+ int ret; - - if (!spi->dev.of_node) { - dev_err(&spi->dev, "Missing device tree\n"); -@@ -962,12 +962,8 @@ qca_spi_probe(struct spi_device *spi) - - spi_set_drvdata(spi, qcaspi_devs); - -- mac = of_get_mac_address(spi->dev.of_node); -- -- if (!IS_ERR(mac)) -- ether_addr_copy(qca->net_dev->dev_addr, mac); -- -- if (!is_valid_ether_addr(qca->net_dev->dev_addr)) { -+ ret = of_get_mac_address(spi->dev.of_node, qca->net_dev->dev_addr); -+ if (ret) { - eth_hw_addr_random(qca->net_dev); - dev_info(&spi->dev, "Using random MAC address: %pM\n", - qca->net_dev->dev_addr); ---- a/drivers/net/ethernet/qualcomm/qca_uart.c -+++ b/drivers/net/ethernet/qualcomm/qca_uart.c -@@ -323,7 +323,6 @@ static int qca_uart_probe(struct serdev_ - { - struct net_device *qcauart_dev = alloc_etherdev(sizeof(struct qcauart)); - struct qcauart *qca; -- const char *mac; - u32 speed = 115200; - int ret; - -@@ -348,12 +347,8 @@ static int qca_uart_probe(struct serdev_ - - of_property_read_u32(serdev->dev.of_node, "current-speed", &speed); - -- mac = of_get_mac_address(serdev->dev.of_node); -- -- if (!IS_ERR(mac)) -- ether_addr_copy(qca->net_dev->dev_addr, mac); -- -- if (!is_valid_ether_addr(qca->net_dev->dev_addr)) { -+ ret = of_get_mac_address(serdev->dev.of_node, qca->net_dev->dev_addr); -+ if (ret) { - eth_hw_addr_random(qca->net_dev); - dev_info(&serdev->dev, "Using random MAC address: %pM\n", - qca->net_dev->dev_addr); ---- a/drivers/net/ethernet/renesas/ravb_main.c -+++ b/drivers/net/ethernet/renesas/ravb_main.c -@@ -109,11 +109,13 @@ static void ravb_set_buffer_align(struct - * Ethernet AVB device doesn't have ROM for MAC address. - * This function gets the MAC address that was used by a bootloader. - */ --static void ravb_read_mac_address(struct net_device *ndev, const u8 *mac) -+static void ravb_read_mac_address(struct device_node *np, -+ struct net_device *ndev) - { -- if (!IS_ERR(mac)) { -- ether_addr_copy(ndev->dev_addr, mac); -- } else { -+ int ret; -+ -+ ret = of_get_mac_address(np, ndev->dev_addr); -+ if (ret) { - u32 mahr = ravb_read(ndev, MAHR); - u32 malr = ravb_read(ndev, MALR); - -@@ -2189,7 +2191,7 @@ static int ravb_probe(struct platform_de - priv->msg_enable = RAVB_DEF_MSG_ENABLE; - - /* Read and set MAC address */ -- ravb_read_mac_address(ndev, of_get_mac_address(np)); -+ ravb_read_mac_address(np, ndev); - if (!is_valid_ether_addr(ndev->dev_addr)) { - dev_warn(&pdev->dev, - "no valid MAC address supplied, using a random one\n"); ---- a/drivers/net/ethernet/renesas/sh_eth.c -+++ b/drivers/net/ethernet/renesas/sh_eth.c -@@ -3145,7 +3145,6 @@ static struct sh_eth_plat_data *sh_eth_p - struct device_node *np = dev->of_node; - struct sh_eth_plat_data *pdata; - phy_interface_t interface; -- const char *mac_addr; - int ret; - - pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); -@@ -3157,9 +3156,7 @@ static struct sh_eth_plat_data *sh_eth_p - return NULL; - pdata->phy_interface = interface; - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(pdata->mac_addr, mac_addr); -+ of_get_mac_address(np, pdata->mac_addr); - - pdata->no_ether_link = - of_property_read_bool(np, "renesas,no-ether-link"); ---- a/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c -+++ b/drivers/net/ethernet/samsung/sxgbe/sxgbe_platform.c -@@ -25,8 +25,7 @@ - - #ifdef CONFIG_OF - static int sxgbe_probe_config_dt(struct platform_device *pdev, -- struct sxgbe_plat_data *plat, -- const char **mac) -+ struct sxgbe_plat_data *plat) - { - struct device_node *np = pdev->dev.of_node; - struct sxgbe_dma_cfg *dma_cfg; -@@ -35,7 +34,6 @@ static int sxgbe_probe_config_dt(struct - if (!np) - return -ENODEV; - -- *mac = of_get_mac_address(np); - err = of_get_phy_mode(np, &plat->interface); - if (err && err != -ENODEV) - return err; -@@ -63,8 +61,7 @@ static int sxgbe_probe_config_dt(struct - } - #else - static int sxgbe_probe_config_dt(struct platform_device *pdev, -- struct sxgbe_plat_data *plat, -- const char **mac) -+ struct sxgbe_plat_data *plat) - { - return -ENOSYS; - } -@@ -85,7 +82,6 @@ static int sxgbe_platform_probe(struct p - void __iomem *addr; - struct sxgbe_priv_data *priv = NULL; - struct sxgbe_plat_data *plat_dat = NULL; -- const char *mac = NULL; - struct net_device *ndev = platform_get_drvdata(pdev); - struct device_node *node = dev->of_node; - -@@ -101,7 +97,7 @@ static int sxgbe_platform_probe(struct p - if (!plat_dat) - return -ENOMEM; - -- ret = sxgbe_probe_config_dt(pdev, plat_dat, &mac); -+ ret = sxgbe_probe_config_dt(pdev, plat_dat); - if (ret) { - pr_err("%s: main dt probe failed\n", __func__); - return ret; -@@ -122,8 +118,7 @@ static int sxgbe_platform_probe(struct p - } - - /* Get MAC address if available (DT) */ -- if (!IS_ERR_OR_NULL(mac)) -- ether_addr_copy(priv->dev->dev_addr, mac); -+ of_get_mac_address(node, priv->dev->dev_addr); - - /* Get the TX/RX IRQ numbers */ - for (i = 0, chan = 1; i < SXGBE_TX_QUEUES; i++) { ---- a/drivers/net/ethernet/socionext/sni_ave.c -+++ b/drivers/net/ethernet/socionext/sni_ave.c -@@ -1559,7 +1559,6 @@ static int ave_probe(struct platform_dev - struct ave_private *priv; - struct net_device *ndev; - struct device_node *np; -- const void *mac_addr; - void __iomem *base; - const char *name; - int i, irq, ret; -@@ -1600,12 +1599,9 @@ static int ave_probe(struct platform_dev - - ndev->max_mtu = AVE_MAX_ETHFRAME - (ETH_HLEN + ETH_FCS_LEN); - -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- -- /* if the mac address is invalid, use random mac address */ -- if (!is_valid_ether_addr(ndev->dev_addr)) { -+ ret = of_get_mac_address(np, ndev->dev_addr); -+ if (ret) { -+ /* if the mac address is invalid, use random mac address */ - eth_hw_addr_random(ndev); - dev_warn(dev, "Using random MAC address: %pM\n", - ndev->dev_addr); ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-anarion.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-anarion.c -@@ -115,7 +115,7 @@ static int anarion_dwmac_probe(struct pl - if (IS_ERR(gmac)) - return PTR_ERR(gmac); - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c -@@ -444,7 +444,7 @@ static int dwc_eth_dwmac_probe(struct pl - if (IS_ERR(stmmac_res.addr)) - return PTR_ERR(stmmac_res.addr); - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-generic.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-generic.c -@@ -27,7 +27,7 @@ static int dwmac_generic_probe(struct pl - return ret; - - if (pdev->dev.of_node) { -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) { - dev_err(&pdev->dev, "dt configuration failed\n"); - return PTR_ERR(plat_dat); ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c -@@ -226,7 +226,7 @@ static int imx_dwmac_probe(struct platfo - if (!dwmac) - return -ENOMEM; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c -@@ -88,7 +88,7 @@ static int intel_eth_plat_probe(struct p - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) { - dev_err(&pdev->dev, "dt configuration failed\n"); - return PTR_ERR(plat_dat); ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c -@@ -255,7 +255,7 @@ static int ipq806x_gmac_probe(struct pla - if (val) - return val; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c -@@ -37,7 +37,7 @@ static int lpc18xx_dwmac_probe(struct pl - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c -@@ -407,7 +407,7 @@ static int mediatek_dwmac_probe(struct p - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c -@@ -52,7 +52,7 @@ static int meson6_dwmac_probe(struct pla - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c -@@ -372,7 +372,7 @@ static int meson8b_dwmac_probe(struct pl - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c -@@ -118,7 +118,7 @@ static int oxnas_dwmac_probe(struct plat - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c -@@ -461,7 +461,7 @@ static int qcom_ethqos_probe(struct plat - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) { - dev_err(&pdev->dev, "dt configuration failed\n"); - return PTR_ERR(plat_dat); ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c -@@ -1396,7 +1396,7 @@ static int rk_gmac_probe(struct platform - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c -@@ -398,7 +398,7 @@ static int socfpga_dwmac_probe(struct pl - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c -@@ -325,7 +325,7 @@ static int sti_dwmac_probe(struct platfo - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c -@@ -371,7 +371,7 @@ static int stm32_dwmac_probe(struct plat - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c -@@ -1202,7 +1202,7 @@ static int sun8i_dwmac_probe(struct plat - if (ret) - return -EINVAL; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c -+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c -@@ -108,7 +108,7 @@ static int sun7i_gmac_probe(struct platf - if (ret) - return ret; - -- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); -+ plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); - if (IS_ERR(plat_dat)) - return PTR_ERR(plat_dat); - ---- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h -+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h -@@ -25,7 +25,7 @@ - - struct stmmac_resources { - void __iomem *addr; -- const char *mac; -+ u8 mac[ETH_ALEN]; - int wol_irq; - int lpi_irq; - int irq; ---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c -+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c -@@ -4904,7 +4904,7 @@ int stmmac_dvr_probe(struct device *devi - priv->wol_irq = res->wol_irq; - priv->lpi_irq = res->lpi_irq; - -- if (!IS_ERR_OR_NULL(res->mac)) -+ if (!is_zero_ether_addr(res->mac)) - memcpy(priv->dev->dev_addr, res->mac, ETH_ALEN); - - dev_set_drvdata(device, priv->dev); ---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c -+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c -@@ -394,7 +394,7 @@ static int stmmac_of_get_mac_mode(struct - * set some private fields that will be used by the main at runtime. - */ - struct plat_stmmacenet_data * --stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) -+stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) - { - struct device_node *np = pdev->dev.of_node; - struct plat_stmmacenet_data *plat; -@@ -406,12 +406,12 @@ stmmac_probe_config_dt(struct platform_d - if (!plat) - return ERR_PTR(-ENOMEM); - -- *mac = of_get_mac_address(np); -- if (IS_ERR(*mac)) { -- if (PTR_ERR(*mac) == -EPROBE_DEFER) -- return ERR_CAST(*mac); -+ rc = of_get_mac_address(np, mac); -+ if (rc) { -+ if (rc == -EPROBE_DEFER) -+ return ERR_PTR(rc); - -- *mac = NULL; -+ eth_zero_addr(mac); - } - - phy_mode = device_get_phy_mode(&pdev->dev); -@@ -643,7 +643,7 @@ void stmmac_remove_config_dt(struct plat - } - #else - struct plat_stmmacenet_data * --stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) -+stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) - { - return ERR_PTR(-EINVAL); - } ---- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h -+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h -@@ -12,7 +12,7 @@ - #include "stmmac.h" - - struct plat_stmmacenet_data * --stmmac_probe_config_dt(struct platform_device *pdev, const char **mac); -+stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac); - void stmmac_remove_config_dt(struct platform_device *pdev, - struct plat_stmmacenet_data *plat); - ---- a/drivers/net/ethernet/ti/am65-cpsw-nuss.c -+++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.c -@@ -1741,7 +1741,6 @@ static int am65_cpsw_nuss_init_slave_por - - for_each_child_of_node(node, port_np) { - struct am65_cpsw_port *port; -- const void *mac_addr; - u32 port_id; - - /* it is not a slave port node, continue */ -@@ -1820,15 +1819,15 @@ static int am65_cpsw_nuss_init_slave_por - return ret; - } - -- mac_addr = of_get_mac_address(port_np); -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(port->slave.mac_addr, mac_addr); -- } else if (am65_cpsw_am654_get_efuse_macid(port_np, -- port->port_id, -- port->slave.mac_addr) || -- !is_valid_ether_addr(port->slave.mac_addr)) { -- random_ether_addr(port->slave.mac_addr); -- dev_err(dev, "Use random MAC address\n"); -+ ret = of_get_mac_address(port_np, port->slave.mac_addr); -+ if (ret) { -+ am65_cpsw_am654_get_efuse_macid(port_np, -+ port->port_id, -+ port->slave.mac_addr); -+ if (!is_valid_ether_addr(port->slave.mac_addr)) { -+ random_ether_addr(port->slave.mac_addr); -+ dev_err(dev, "Use random MAC address\n"); -+ } - } - } - of_node_put(node); ---- a/drivers/net/ethernet/ti/cpsw.c -+++ b/drivers/net/ethernet/ti/cpsw.c -@@ -1306,7 +1306,6 @@ static int cpsw_probe_dt(struct cpsw_pla - - for_each_available_child_of_node(node, slave_node) { - struct cpsw_slave_data *slave_data = data->slave_data + i; -- const void *mac_addr = NULL; - int lenp; - const __be32 *parp; - -@@ -1378,10 +1377,8 @@ static int cpsw_probe_dt(struct cpsw_pla - } - - no_phy_slave: -- mac_addr = of_get_mac_address(slave_node); -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(slave_data->mac_addr, mac_addr); -- } else { -+ ret = of_get_mac_address(slave_node, slave_data->mac_addr); -+ if (ret) { - ret = ti_cm_get_macid(&pdev->dev, i, - slave_data->mac_addr); - if (ret) ---- a/drivers/net/ethernet/ti/cpsw_new.c -+++ b/drivers/net/ethernet/ti/cpsw_new.c -@@ -1267,7 +1267,6 @@ static int cpsw_probe_dt(struct cpsw_com - - for_each_child_of_node(tmp_node, port_np) { - struct cpsw_slave_data *slave_data; -- const void *mac_addr; - u32 port_id; - - ret = of_property_read_u32(port_np, "reg", &port_id); -@@ -1326,10 +1325,8 @@ static int cpsw_probe_dt(struct cpsw_com - goto err_node_put; - } - -- mac_addr = of_get_mac_address(port_np); -- if (!IS_ERR(mac_addr)) { -- ether_addr_copy(slave_data->mac_addr, mac_addr); -- } else { -+ ret = of_get_mac_address(port_np, slave_data->mac_addr); -+ if (ret) { - ret = ti_cm_get_macid(dev, port_id - 1, - slave_data->mac_addr); - if (ret) ---- a/drivers/net/ethernet/ti/davinci_emac.c -+++ b/drivers/net/ethernet/ti/davinci_emac.c -@@ -1687,7 +1687,6 @@ davinci_emac_of_get_pdata(struct platfor - const struct of_device_id *match; - const struct emac_platform_data *auxdata; - struct emac_platform_data *pdata = NULL; -- const u8 *mac_addr; - - if (!IS_ENABLED(CONFIG_OF) || !pdev->dev.of_node) - return dev_get_platdata(&pdev->dev); -@@ -1699,11 +1698,8 @@ davinci_emac_of_get_pdata(struct platfor - np = pdev->dev.of_node; - pdata->version = EMAC_VERSION_2; - -- if (!is_valid_ether_addr(pdata->mac_addr)) { -- mac_addr = of_get_mac_address(np); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(pdata->mac_addr, mac_addr); -- } -+ if (!is_valid_ether_addr(pdata->mac_addr)) -+ of_get_mac_address(np, pdata->mac_addr); - - of_property_read_u32(np, "ti,davinci-ctrl-reg-offset", - &pdata->ctrl_reg_offset); ---- a/drivers/net/ethernet/ti/netcp_core.c -+++ b/drivers/net/ethernet/ti/netcp_core.c -@@ -1966,7 +1966,6 @@ static int netcp_create_interface(struct - struct resource res; - void __iomem *efuse = NULL; - u32 efuse_mac = 0; -- const void *mac_addr; - u8 efuse_mac_addr[6]; - u32 temp[2]; - int ret = 0; -@@ -2036,10 +2035,8 @@ static int netcp_create_interface(struct - devm_iounmap(dev, efuse); - devm_release_mem_region(dev, res.start, size); - } else { -- mac_addr = of_get_mac_address(node_interface); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(ndev->dev_addr, mac_addr); -- else -+ ret = of_get_mac_address(node_interface, ndev->dev_addr); -+ if (ret) - eth_random_addr(ndev->dev_addr); - } - ---- a/drivers/net/ethernet/wiznet/w5100-spi.c -+++ b/drivers/net/ethernet/wiznet/w5100-spi.c -@@ -423,8 +423,14 @@ static int w5100_spi_probe(struct spi_de - const struct of_device_id *of_id; - const struct w5100_ops *ops; - kernel_ulong_t driver_data; -+ const void *mac = NULL; -+ u8 tmpmac[ETH_ALEN]; - int priv_size; -- const void *mac = of_get_mac_address(spi->dev.of_node); -+ int ret; -+ -+ ret = of_get_mac_address(spi->dev.of_node, tmpmac); -+ if (!ret) -+ mac = tmpmac; - - if (spi->dev.of_node) { - of_id = of_match_device(w5100_of_match, &spi->dev); ---- a/drivers/net/ethernet/wiznet/w5100.c -+++ b/drivers/net/ethernet/wiznet/w5100.c -@@ -1159,7 +1159,7 @@ int w5100_probe(struct device *dev, cons - INIT_WORK(&priv->setrx_work, w5100_setrx_work); - INIT_WORK(&priv->restart_work, w5100_restart_work); - -- if (!IS_ERR_OR_NULL(mac_addr)) -+ if (mac_addr) - memcpy(ndev->dev_addr, mac_addr, ETH_ALEN); - else - eth_hw_addr_random(ndev); ---- a/drivers/net/ethernet/xilinx/ll_temac_main.c -+++ b/drivers/net/ethernet/xilinx/ll_temac_main.c -@@ -438,7 +438,7 @@ static void temac_do_set_mac_address(str - - static int temac_init_mac_address(struct net_device *ndev, const void *address) - { -- ether_addr_copy(ndev->dev_addr, address); -+ memcpy(ndev->dev_addr, address, ETH_ALEN); - if (!is_valid_ether_addr(ndev->dev_addr)) - eth_hw_addr_random(ndev); - temac_do_set_mac_address(ndev); -@@ -1370,7 +1370,7 @@ static int temac_probe(struct platform_d - struct device_node *temac_np = dev_of_node(&pdev->dev), *dma_np; - struct temac_local *lp; - struct net_device *ndev; -- const void *addr; -+ u8 addr[ETH_ALEN]; - __be32 *p; - bool little_endian; - int rc = 0; -@@ -1561,8 +1561,8 @@ static int temac_probe(struct platform_d - - if (temac_np) { - /* Retrieve the MAC address */ -- addr = of_get_mac_address(temac_np); -- if (IS_ERR(addr)) { -+ rc = of_get_mac_address(temac_np, addr); -+ if (rc) { - dev_err(&pdev->dev, "could not find MAC address\n"); - return -ENODEV; - } ---- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c -+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c -@@ -1803,8 +1803,8 @@ static int axienet_probe(struct platform - struct device_node *np; - struct axienet_local *lp; - struct net_device *ndev; -- const void *mac_addr; - struct resource *ethres; -+ u8 mac_addr[ETH_ALEN]; - int addr_width = 32; - u32 value; - -@@ -2004,13 +2004,14 @@ static int axienet_probe(struct platform - dev_info(&pdev->dev, "Ethernet core IRQ not defined\n"); - - /* Retrieve the MAC address */ -- mac_addr = of_get_mac_address(pdev->dev.of_node); -- if (IS_ERR(mac_addr)) { -- dev_warn(&pdev->dev, "could not find MAC address property: %ld\n", -- PTR_ERR(mac_addr)); -- mac_addr = NULL; -+ ret = of_get_mac_address(pdev->dev.of_node, mac_addr); -+ if (!ret) { -+ axienet_set_mac_address(ndev, mac_addr); -+ } else { -+ dev_warn(&pdev->dev, "could not find MAC address property: %d\n", -+ ret); -+ axienet_set_mac_address(ndev, NULL); - } -- axienet_set_mac_address(ndev, mac_addr); - - lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD; - lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD; ---- a/drivers/net/ethernet/xilinx/xilinx_emaclite.c -+++ b/drivers/net/ethernet/xilinx/xilinx_emaclite.c -@@ -1113,7 +1113,6 @@ static int xemaclite_of_probe(struct pla - struct net_device *ndev = NULL; - struct net_local *lp = NULL; - struct device *dev = &ofdev->dev; -- const void *mac_address; - - int rc = 0; - -@@ -1155,12 +1154,9 @@ static int xemaclite_of_probe(struct pla - lp->next_rx_buf_to_use = 0x0; - lp->tx_ping_pong = get_bool(ofdev, "xlnx,tx-ping-pong"); - lp->rx_ping_pong = get_bool(ofdev, "xlnx,rx-ping-pong"); -- mac_address = of_get_mac_address(ofdev->dev.of_node); - -- if (!IS_ERR(mac_address)) { -- /* Set the MAC address. */ -- ether_addr_copy(ndev->dev_addr, mac_address); -- } else { -+ rc = of_get_mac_address(ofdev->dev.of_node, ndev->dev_addr); -+ if (rc) { - dev_warn(dev, "No MAC address found, using random\n"); - eth_hw_addr_random(ndev); - } ---- a/drivers/net/wireless/ath/ath9k/init.c -+++ b/drivers/net/wireless/ath/ath9k/init.c -@@ -618,7 +618,6 @@ static int ath9k_of_init(struct ath_soft - struct ath_hw *ah = sc->sc_ah; - struct ath_common *common = ath9k_hw_common(ah); - enum ath_bus_type bus_type = common->bus_ops->ath_bus_type; -- const char *mac; - char eeprom_name[100]; - int ret; - -@@ -641,9 +640,7 @@ static int ath9k_of_init(struct ath_soft - ah->ah_flags |= AH_NO_EEP_SWAP; - } - -- mac = of_get_mac_address(np); -- if (!IS_ERR(mac)) -- ether_addr_copy(common->macaddr, mac); -+ of_get_mac_address(np, common->macaddr); - - return 0; - } ---- a/drivers/net/wireless/mediatek/mt76/eeprom.c -+++ b/drivers/net/wireless/mediatek/mt76/eeprom.c -@@ -90,15 +90,9 @@ out_put_node: - void - mt76_eeprom_override(struct mt76_dev *dev) - { --#ifdef CONFIG_OF - struct device_node *np = dev->dev->of_node; -- const u8 *mac = NULL; - -- if (np) -- mac = of_get_mac_address(np); -- if (!IS_ERR_OR_NULL(mac)) -- ether_addr_copy(dev->macaddr, mac); --#endif -+ of_get_mac_address(np, dev->macaddr); - - if (!is_valid_ether_addr(dev->macaddr)) { - eth_random_addr(dev->macaddr); ---- a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c -+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c -@@ -990,11 +990,7 @@ static void rt2x00lib_rate(struct ieee80 - - void rt2x00lib_set_mac_address(struct rt2x00_dev *rt2x00dev, u8 *eeprom_mac_addr) - { -- const char *mac_addr; -- -- mac_addr = of_get_mac_address(rt2x00dev->dev->of_node); -- if (!IS_ERR(mac_addr)) -- ether_addr_copy(eeprom_mac_addr, mac_addr); -+ of_get_mac_address(rt2x00dev->dev->of_node, eeprom_mac_addr); - - if (!is_valid_ether_addr(eeprom_mac_addr)) { - eth_random_addr(eeprom_mac_addr); ---- a/drivers/of/of_net.c -+++ b/drivers/of/of_net.c -@@ -45,37 +45,29 @@ int of_get_phy_mode(struct device_node * - } - EXPORT_SYMBOL_GPL(of_get_phy_mode); - --static const void *of_get_mac_addr(struct device_node *np, const char *name) -+static int of_get_mac_addr(struct device_node *np, const char *name, u8 *addr) - { - struct property *pp = of_find_property(np, name, NULL); - -- if (pp && pp->length == ETH_ALEN && is_valid_ether_addr(pp->value)) -- return pp->value; -- return NULL; -+ if (pp && pp->length == ETH_ALEN && is_valid_ether_addr(pp->value)) { -+ memcpy(addr, pp->value, ETH_ALEN); -+ return 0; -+ } -+ return -ENODEV; - } - --static const void *of_get_mac_addr_nvmem(struct device_node *np) -+static int of_get_mac_addr_nvmem(struct device_node *np, u8 *addr) - { -- int ret; -- const void *mac; -- u8 nvmem_mac[ETH_ALEN]; - struct platform_device *pdev = of_find_device_by_node(np); -+ int ret; - - if (!pdev) -- return ERR_PTR(-ENODEV); -+ return -ENODEV; - -- ret = nvmem_get_mac_address(&pdev->dev, &nvmem_mac); -- if (ret) { -- put_device(&pdev->dev); -- return ERR_PTR(ret); -- } -- -- mac = devm_kmemdup(&pdev->dev, nvmem_mac, ETH_ALEN, GFP_KERNEL); -+ ret = nvmem_get_mac_address(&pdev->dev, addr); - put_device(&pdev->dev); -- if (!mac) -- return ERR_PTR(-ENOMEM); - -- return mac; -+ return ret; - } - - /** -@@ -98,24 +90,27 @@ static const void *of_get_mac_addr_nvmem - * this case, the real MAC is in 'local-mac-address', and 'mac-address' exists - * but is all zeros. - * -- * Return: Will be a valid pointer on success and ERR_PTR in case of error. -+ * Return: 0 on success and errno in case of error. - */ --const void *of_get_mac_address(struct device_node *np) -+int of_get_mac_address(struct device_node *np, u8 *addr) - { -- const void *addr; -- -- addr = of_get_mac_addr(np, "mac-address"); -- if (addr) -- return addr; -+ int ret; - -- addr = of_get_mac_addr(np, "local-mac-address"); -- if (addr) -- return addr; -+ if (!np) -+ return -ENODEV; - -- addr = of_get_mac_addr(np, "address"); -- if (addr) -- return addr; -+ ret = of_get_mac_addr(np, "mac-address", addr); -+ if (!ret) -+ return 0; -+ -+ ret = of_get_mac_addr(np, "local-mac-address", addr); -+ if (!ret) -+ return 0; -+ -+ ret = of_get_mac_addr(np, "address", addr); -+ if (!ret) -+ return 0; - -- return of_get_mac_addr_nvmem(np); -+ return of_get_mac_addr_nvmem(np, addr); - } - EXPORT_SYMBOL(of_get_mac_address); ---- a/drivers/staging/octeon/ethernet.c -+++ b/drivers/staging/octeon/ethernet.c -@@ -407,14 +407,10 @@ static int cvm_oct_common_set_mac_addres - int cvm_oct_common_init(struct net_device *dev) - { - struct octeon_ethernet *priv = netdev_priv(dev); -- const u8 *mac = NULL; -+ int ret; - -- if (priv->of_node) -- mac = of_get_mac_address(priv->of_node); -- -- if (!IS_ERR_OR_NULL(mac)) -- ether_addr_copy(dev->dev_addr, mac); -- else -+ ret = of_get_mac_address(priv->of_node, dev->dev_addr); -+ if (ret) - eth_hw_addr_random(dev); - - /* ---- a/drivers/staging/wfx/main.c -+++ b/drivers/staging/wfx/main.c -@@ -334,7 +334,6 @@ int wfx_probe(struct wfx_dev *wdev) - { - int i; - int err; -- const void *macaddr; - struct gpio_desc *gpio_saved; - - // During first part of boot, gpio_wakeup cannot yet been used. So -@@ -423,9 +422,9 @@ int wfx_probe(struct wfx_dev *wdev) - - for (i = 0; i < ARRAY_SIZE(wdev->addresses); i++) { - eth_zero_addr(wdev->addresses[i].addr); -- macaddr = of_get_mac_address(wdev->dev->of_node); -- if (!IS_ERR_OR_NULL(macaddr)) { -- ether_addr_copy(wdev->addresses[i].addr, macaddr); -+ err = of_get_mac_address(wdev->dev->of_node, -+ wdev->addresses[i].addr); -+ if (!err) { - wdev->addresses[i].addr[ETH_ALEN - 1] += i; - } else { - ether_addr_copy(wdev->addresses[i].addr, ---- a/include/linux/of_net.h -+++ b/include/linux/of_net.h -@@ -13,7 +13,7 @@ - - struct net_device; - extern int of_get_phy_mode(struct device_node *np, phy_interface_t *interface); --extern const void *of_get_mac_address(struct device_node *np); -+extern int of_get_mac_address(struct device_node *np, u8 *mac); - extern struct net_device *of_find_net_device_by_node(struct device_node *np); - #else - static inline int of_get_phy_mode(struct device_node *np, -@@ -22,9 +22,9 @@ static inline int of_get_phy_mode(struct - return -ENODEV; - } - --static inline const void *of_get_mac_address(struct device_node *np) -+static inline int of_get_mac_address(struct device_node *np, u8 *mac) - { -- return ERR_PTR(-ENODEV); -+ return -ENODEV; - } - - static inline struct net_device *of_find_net_device_by_node(struct device_node *np) ---- a/include/net/dsa.h -+++ b/include/net/dsa.h -@@ -208,7 +208,7 @@ struct dsa_port { - unsigned int index; - const char *name; - struct dsa_port *cpu_dp; -- const char *mac; -+ u8 mac[ETH_ALEN]; - struct device_node *dn; - unsigned int ageing_time; - bool vlan_filtering; ---- a/net/dsa/dsa2.c -+++ b/net/dsa/dsa2.c -@@ -288,7 +288,7 @@ static int dsa_port_setup(struct dsa_por - - break; - case DSA_PORT_TYPE_USER: -- dp->mac = of_get_mac_address(dp->dn); -+ of_get_mac_address(dp->dn, dp->mac); - err = dsa_slave_create(dp); - if (err) - break; ---- a/net/dsa/slave.c -+++ b/net/dsa/slave.c -@@ -1855,7 +1855,7 @@ int dsa_slave_create(struct dsa_port *po - slave_dev->hw_features |= NETIF_F_HW_TC; - slave_dev->features |= NETIF_F_LLTX; - slave_dev->ethtool_ops = &dsa_slave_ethtool_ops; -- if (!IS_ERR_OR_NULL(port->mac)) -+ if (!is_zero_ether_addr(port->mac)) - ether_addr_copy(slave_dev->dev_addr, port->mac); - else - eth_hw_addr_inherit(slave_dev, master); ---- a/net/ethernet/eth.c -+++ b/net/ethernet/eth.c -@@ -506,13 +506,14 @@ unsigned char * __weak arch_get_platform - - int eth_platform_get_mac_address(struct device *dev, u8 *mac_addr) - { -- const unsigned char *addr = NULL; -+ unsigned char *addr; -+ int ret; - -- if (dev->of_node) -- addr = of_get_mac_address(dev->of_node); -- if (IS_ERR_OR_NULL(addr)) -- addr = arch_get_platform_mac_address(); -+ ret = of_get_mac_address(dev->of_node, mac_addr); -+ if (!ret) -+ return 0; - -+ addr = arch_get_platform_mac_address(); - if (!addr) - return -ENODEV; - diff --git a/target/linux/generic/backport-5.10/782-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch b/target/linux/generic/backport-5.10/782-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch deleted file mode 100644 index 245c5f3bd6..0000000000 --- a/target/linux/generic/backport-5.10/782-net-next-2-of-net-fix-of_get_mac_addr_nvmem-for-non-platform-devices.patch +++ /dev/null @@ -1,77 +0,0 @@ -From f10843e04a075202dbb39dfcee047e3a2fdf5a8d Mon Sep 17 00:00:00 2001 -From: Michael Walle -Date: Mon, 12 Apr 2021 19:47:18 +0200 -Subject: of: net: fix of_get_mac_addr_nvmem() for non-platform devices - -of_get_mac_address() already supports fetching the MAC address by an -nvmem provider. But until now, it was just working for platform devices. -Esp. it was not working for DSA ports and PCI devices. It gets more -common that PCI devices have a device tree binding since SoCs contain -integrated root complexes. - -Use the nvmem of_* binding to fetch the nvmem cells by a struct -device_node. We still have to try to read the cell by device first -because there might be a nvmem_cell_lookup associated with that device. - -Signed-off-by: Michael Walle -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/of/of_net.c | 35 ++++++++++++++++++++++++++++++----- - 1 file changed, 30 insertions(+), 5 deletions(-) - ---- a/drivers/of/of_net.c -+++ b/drivers/of/of_net.c -@@ -11,6 +11,7 @@ - #include - #include - #include -+#include - - /** - * of_get_phy_mode - Get phy mode for given device_node -@@ -59,15 +60,39 @@ static int of_get_mac_addr(struct device - static int of_get_mac_addr_nvmem(struct device_node *np, u8 *addr) - { - struct platform_device *pdev = of_find_device_by_node(np); -+ struct nvmem_cell *cell; -+ const void *mac; -+ size_t len; - int ret; - -- if (!pdev) -- return -ENODEV; -+ /* Try lookup by device first, there might be a nvmem_cell_lookup -+ * associated with a given device. -+ */ -+ if (pdev) { -+ ret = nvmem_get_mac_address(&pdev->dev, addr); -+ put_device(&pdev->dev); -+ return ret; -+ } -+ -+ cell = of_nvmem_cell_get(np, "mac-address"); -+ if (IS_ERR(cell)) -+ return PTR_ERR(cell); -+ -+ mac = nvmem_cell_read(cell, &len); -+ nvmem_cell_put(cell); -+ -+ if (IS_ERR(mac)) -+ return PTR_ERR(mac); -+ -+ if (len != ETH_ALEN || !is_valid_ether_addr(mac)) { -+ kfree(mac); -+ return -EINVAL; -+ } - -- ret = nvmem_get_mac_address(&pdev->dev, addr); -- put_device(&pdev->dev); -+ memcpy(addr, mac, ETH_ALEN); -+ kfree(mac); - -- return ret; -+ return 0; - } - - /** diff --git a/target/linux/generic/backport-5.10/783-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch b/target/linux/generic/backport-5.10/783-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch deleted file mode 100644 index 6e7f20634f..0000000000 --- a/target/linux/generic/backport-5.10/783-v5.15-0001-net-bgmac-bcma-handle-deferred-probe-error-due-to-ma.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 029497e66bdc762e001880e4c85a91f35a54b1e2 Mon Sep 17 00:00:00 2001 -From: Christian Lamparter -Date: Sun, 19 Sep 2021 13:57:25 +0200 -Subject: [PATCH] net: bgmac-bcma: handle deferred probe error due to - mac-address -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Due to the inclusion of nvmem handling into the mac-address getter -function of_get_mac_address() by -commit d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") -it is now possible to get a -EPROBE_DEFER return code. Which did cause -bgmac to assign a random ethernet address. - -This exact issue happened on my Meraki MR32. The nvmem provider is -an EEPROM (at24c64) which gets instantiated once the module -driver is loaded... This happens once the filesystem becomes available. - -With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error. -Then the driver subsystem will reschedule the probe at a later time. - -Cc: Petr Å tetiar -Cc: Michael Walle -Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") -Signed-off-by: Christian Lamparter -Signed-off-by: David S. Miller ---- - drivers/net/ethernet/broadcom/bgmac-bcma.c | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/drivers/net/ethernet/broadcom/bgmac-bcma.c -+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c -@@ -129,6 +129,8 @@ static int bgmac_probe(struct bcma_devic - bcma_set_drvdata(core, bgmac); - - err = of_get_mac_address(bgmac->dev->of_node, bgmac->net_dev->dev_addr); -+ if (err == -EPROBE_DEFER) -+ return err; - - /* If no MAC address assigned via device tree, check SPROM */ - if (err) { diff --git a/target/linux/generic/backport-5.10/783-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch b/target/linux/generic/backport-5.10/783-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch deleted file mode 100644 index bde62f3b1b..0000000000 --- a/target/linux/generic/backport-5.10/783-v5.15-0002-net-bgmac-platform-handle-mac-address-deferral.patch +++ /dev/null @@ -1,36 +0,0 @@ -From 763716a55cb1f480ffe1a9702e6b5d9ea1a80a24 Mon Sep 17 00:00:00 2001 -From: Matthew Hagan -Date: Sat, 25 Sep 2021 11:36:27 +0000 -Subject: [PATCH] net: bgmac-platform: handle mac-address deferral - -This patch is a replication of Christian Lamparter's "net: bgmac-bcma: -handle deferred probe error due to mac-address" patch for the -bgmac-platform driver [1]. - -As is the case with the bgmac-bcma driver, this change is to cover the -scenario where the MAC address cannot yet be discovered due to reliance -on an nvmem provider which is yet to be instantiated, resulting in a -random address being assigned that has to be manually overridden. - -[1] https://lore.kernel.org/netdev/20210919115725.29064-1-chunkeey@gmail.com - -Signed-off-by: Matthew Hagan -Reviewed-by: Andrew Lunn -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/ethernet/broadcom/bgmac-platform.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/net/ethernet/broadcom/bgmac-platform.c -+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c -@@ -193,6 +193,9 @@ static int bgmac_probe(struct platform_d - bgmac->dma_dev = &pdev->dev; - - ret = of_get_mac_address(np, bgmac->net_dev->dev_addr); -+ if (ret == -EPROBE_DEFER) -+ return ret; -+ - if (ret) - dev_warn(&pdev->dev, - "MAC address not present in device tree\n"); diff --git a/target/linux/generic/backport-5.10/784-v5.16-0001-net-bgmac-improve-handling-PHY.patch b/target/linux/generic/backport-5.10/784-v5.16-0001-net-bgmac-improve-handling-PHY.patch deleted file mode 100644 index 6788a2ec35..0000000000 --- a/target/linux/generic/backport-5.10/784-v5.16-0001-net-bgmac-improve-handling-PHY.patch +++ /dev/null @@ -1,84 +0,0 @@ -From b5375509184dc23d2b7fa0c5ed8763899ccc9674 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Sat, 2 Oct 2021 19:58:11 +0200 -Subject: [PATCH] net: bgmac: improve handling PHY -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -1. Use info from DT if available - -It allows describing for example a fixed link. It's more accurate than -just guessing there may be one (depending on a chipset). - -2. Verify PHY ID before trying to connect PHY - -PHY addr 0x1e (30) is special in Broadcom routers and means a switch -connected as MDIO devices instead of a real PHY. Don't try connecting to -it. - -Signed-off-by: Rafał Miłecki -Signed-off-by: David S. Miller ---- - drivers/net/ethernet/broadcom/bgmac-bcma.c | 33 ++++++++++++++-------- - 1 file changed, 21 insertions(+), 12 deletions(-) - ---- a/drivers/net/ethernet/broadcom/bgmac-bcma.c -+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c -@@ -11,6 +11,7 @@ - #include - #include - #include -+#include - #include - #include "bgmac.h" - -@@ -86,17 +87,28 @@ static int bcma_phy_connect(struct bgmac - struct phy_device *phy_dev; - char bus_id[MII_BUS_ID_SIZE + 3]; - -+ /* DT info should be the most accurate */ -+ phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node, -+ bgmac_adjust_link); -+ if (phy_dev) -+ return 0; -+ - /* Connect to the PHY */ -- snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id, -- bgmac->phyaddr); -- phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link, -- PHY_INTERFACE_MODE_MII); -- if (IS_ERR(phy_dev)) { -- dev_err(bgmac->dev, "PHY connection failed\n"); -- return PTR_ERR(phy_dev); -+ if (bgmac->mii_bus && bgmac->phyaddr != BGMAC_PHY_NOREGS) { -+ snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id, -+ bgmac->phyaddr); -+ phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link, -+ PHY_INTERFACE_MODE_MII); -+ if (IS_ERR(phy_dev)) { -+ dev_err(bgmac->dev, "PHY connection failed\n"); -+ return PTR_ERR(phy_dev); -+ } -+ -+ return 0; - } - -- return 0; -+ /* Assume a fixed link to the switch port */ -+ return bgmac_phy_connect_direct(bgmac); - } - - static const struct bcma_device_id bgmac_bcma_tbl[] = { -@@ -297,10 +309,7 @@ static int bgmac_probe(struct bcma_devic - bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset; - bgmac->get_bus_clock = bcma_bgmac_get_bus_clock; - bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32; -- if (bgmac->mii_bus) -- bgmac->phy_connect = bcma_phy_connect; -- else -- bgmac->phy_connect = bgmac_phy_connect_direct; -+ bgmac->phy_connect = bcma_phy_connect; - - err = bgmac_enet_probe(bgmac); - if (err) diff --git a/target/linux/generic/backport-5.10/784-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch b/target/linux/generic/backport-5.10/784-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch deleted file mode 100644 index f134828273..0000000000 --- a/target/linux/generic/backport-5.10/784-v5.16-0002-net-bgmac-support-MDIO-described-in-DT.patch +++ /dev/null @@ -1,54 +0,0 @@ -From 45c9d966688e7fad7f24bfc450547d91e4304d0b Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Sat, 2 Oct 2021 19:58:12 +0200 -Subject: [PATCH] net: bgmac: support MDIO described in DT -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Check ethernet controller DT node for "mdio" subnode and use it with -of_mdiobus_register() when present. That allows specifying MDIO and its -PHY devices in a standard DT based way. - -This is required for BCM53573 SoC support. That family is sometimes -called Northstar (by marketing?) but is quite different from it. It uses -different CPU(s) and many different hw blocks. - -One of shared blocks in BCM53573 is Ethernet controller. Switch however -is not SRAB accessible (as it Northstar) but is MDIO attached. - -Signed-off-by: Rafał Miłecki -Signed-off-by: David S. Miller ---- - drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c | 6 +++++- - 1 file changed, 5 insertions(+), 1 deletion(-) - ---- a/drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c -+++ b/drivers/net/ethernet/broadcom/bgmac-bcma-mdio.c -@@ -10,6 +10,7 @@ - - #include - #include -+#include - #include "bgmac.h" - - static bool bcma_mdio_wait_value(struct bcma_device *core, u16 reg, u32 mask, -@@ -211,6 +212,7 @@ struct mii_bus *bcma_mdio_mii_register(s - { - struct bcma_device *core = bgmac->bcma.core; - struct mii_bus *mii_bus; -+ struct device_node *np; - int err; - - mii_bus = mdiobus_alloc(); -@@ -229,7 +231,9 @@ struct mii_bus *bcma_mdio_mii_register(s - mii_bus->parent = &core->dev; - mii_bus->phy_mask = ~(1 << bgmac->phyaddr); - -- err = mdiobus_register(mii_bus); -+ np = of_get_child_by_name(core->dev.of_node, "mdio"); -+ -+ err = of_mdiobus_register(mii_bus, np); - if (err) { - dev_err(&core->dev, "Registration of mii bus failed\n"); - goto err_free_bus; diff --git a/target/linux/generic/backport-5.10/785-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch b/target/linux/generic/backport-5.10/785-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch deleted file mode 100644 index b8e6d9b613..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-01-net-dsa-qca8k-change-simple-print-to-dev-variant.patch +++ /dev/null @@ -1,35 +0,0 @@ -From 5d9e068402dcf7354cc8ee66c2152845306d2ccb Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:51 +0200 -Subject: [PATCH] net: dsa: qca8k: change simple print to dev variant - -Change pr_err and pr_warn to dev variant. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -701,7 +701,7 @@ qca8k_setup(struct dsa_switch *ds) - - /* Make sure that port 0 is the cpu port */ - if (!dsa_is_cpu_port(ds, 0)) { -- pr_err("port 0 is not the CPU port\n"); -+ dev_err(priv->dev, "port 0 is not the CPU port"); - return -EINVAL; - } - -@@ -711,7 +711,7 @@ qca8k_setup(struct dsa_switch *ds) - priv->regmap = devm_regmap_init(ds->dev, NULL, priv, - &qca8k_regmap_config); - if (IS_ERR(priv->regmap)) -- pr_warn("regmap initialization failed"); -+ dev_warn(priv->dev, "regmap initialization failed"); - - ret = qca8k_setup_mdio_bus(priv); - if (ret) diff --git a/target/linux/generic/backport-5.10/785-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch b/target/linux/generic/backport-5.10/785-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch deleted file mode 100644 index ff8288d484..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-02-net-dsa-qca8k-use-iopoll-macro-for-qca8k_busy_wait.patch +++ /dev/null @@ -1,61 +0,0 @@ -From 2ad255f2faaffb3af786031fba2e7955454b558a Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:52 +0200 -Subject: [PATCH] net: dsa: qca8k: use iopoll macro for qca8k_busy_wait - -Use iopoll macro instead of while loop. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 23 +++++++++++------------ - drivers/net/dsa/qca8k.h | 2 ++ - 2 files changed, 13 insertions(+), 12 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -262,21 +262,20 @@ static struct regmap_config qca8k_regmap - static int - qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) - { -- unsigned long timeout; -+ u32 val; -+ int ret; - -- timeout = jiffies + msecs_to_jiffies(20); -+ ret = read_poll_timeout(qca8k_read, val, !(val & mask), -+ 0, QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, -+ priv, reg); - -- /* loop until the busy flag has cleared */ -- do { -- u32 val = qca8k_read(priv, reg); -- int busy = val & mask; -+ /* Check if qca8k_read has failed for a different reason -+ * before returning -ETIMEDOUT -+ */ -+ if (ret < 0 && val < 0) -+ return val; - -- if (!busy) -- break; -- cond_resched(); -- } while (!time_after_eq(jiffies, timeout)); -- -- return time_after_eq(jiffies, timeout); -+ return ret; - } - - static void ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -18,6 +18,8 @@ - #define PHY_ID_QCA8337 0x004dd036 - #define QCA8K_ID_QCA8337 0x13 - -+#define QCA8K_BUSY_WAIT_TIMEOUT 20 -+ - #define QCA8K_NUM_FDB_RECORDS 2048 - - #define QCA8K_CPU_PORT 0 diff --git a/target/linux/generic/backport-5.10/785-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch b/target/linux/generic/backport-5.10/785-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch deleted file mode 100644 index c403589874..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-03-net-dsa-qca8k-improve-qca8k-read-write-rmw-bus-acces.patch +++ /dev/null @@ -1,86 +0,0 @@ -From 504bf65931824eda83494e5b5d75686e27ace03e Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:53 +0200 -Subject: [PATCH] net: dsa: qca8k: improve qca8k read/write/rmw bus access - -Put bus in local variable to improve faster access to the mdio bus. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 29 ++++++++++++++++------------- - 1 file changed, 16 insertions(+), 13 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -142,17 +142,18 @@ qca8k_set_page(struct mii_bus *bus, u16 - static u32 - qca8k_read(struct qca8k_priv *priv, u32 reg) - { -+ struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 val; - - qca8k_split_addr(reg, &r1, &r2, &page); - -- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(priv->bus, page); -- val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); -+ qca8k_set_page(bus, page); -+ val = qca8k_mii_read32(bus, 0x10 | r2, r1); - -- mutex_unlock(&priv->bus->mdio_lock); -+ mutex_unlock(&bus->mdio_lock); - - return val; - } -@@ -160,35 +161,37 @@ qca8k_read(struct qca8k_priv *priv, u32 - static void - qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) - { -+ struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - - qca8k_split_addr(reg, &r1, &r2, &page); - -- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(priv->bus, page); -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); -+ qca8k_set_page(bus, page); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, val); - -- mutex_unlock(&priv->bus->mdio_lock); -+ mutex_unlock(&bus->mdio_lock); - } - - static u32 - qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 val) - { -+ struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 ret; - - qca8k_split_addr(reg, &r1, &r2, &page); - -- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(priv->bus, page); -- ret = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); -+ qca8k_set_page(bus, page); -+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1); - ret &= ~mask; - ret |= val; -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, ret); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, ret); - -- mutex_unlock(&priv->bus->mdio_lock); -+ mutex_unlock(&bus->mdio_lock); - - return ret; - } diff --git a/target/linux/generic/backport-5.10/785-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch b/target/linux/generic/backport-5.10/785-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch deleted file mode 100644 index 6be494a8c7..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-04-net-dsa-qca8k-handle-qca8k_set_page-errors.patch +++ /dev/null @@ -1,101 +0,0 @@ -From ba5707ec58cfb6853dff41c2aae72deb6a03d389 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:54 +0200 -Subject: [PATCH] net: dsa: qca8k: handle qca8k_set_page errors - -With a remote possibility, the set_page function can fail. Since this is -a critical part of the write/read qca8k regs, propagate the error and -terminate any read/write operation. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 33 ++++++++++++++++++++++++++------- - 1 file changed, 26 insertions(+), 7 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -127,16 +127,23 @@ qca8k_mii_write32(struct mii_bus *bus, i - "failed to write qca8k 32bit register\n"); - } - --static void -+static int - qca8k_set_page(struct mii_bus *bus, u16 page) - { -+ int ret; -+ - if (page == qca8k_current_page) -- return; -+ return 0; - -- if (bus->write(bus, 0x18, 0, page) < 0) -+ ret = bus->write(bus, 0x18, 0, page); -+ if (ret < 0) { - dev_err_ratelimited(&bus->dev, - "failed to set qca8k page\n"); -+ return ret; -+ } -+ - qca8k_current_page = page; -+ return 0; - } - - static u32 -@@ -150,11 +157,14 @@ qca8k_read(struct qca8k_priv *priv, u32 - - mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(bus, page); -+ val = qca8k_set_page(bus, page); -+ if (val < 0) -+ goto exit; -+ - val = qca8k_mii_read32(bus, 0x10 | r2, r1); - -+exit: - mutex_unlock(&bus->mdio_lock); -- - return val; - } - -@@ -163,14 +173,19 @@ qca8k_write(struct qca8k_priv *priv, u32 - { - struct mii_bus *bus = priv->bus; - u16 r1, r2, page; -+ int ret; - - qca8k_split_addr(reg, &r1, &r2, &page); - - mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(bus, page); -+ ret = qca8k_set_page(bus, page); -+ if (ret < 0) -+ goto exit; -+ - qca8k_mii_write32(bus, 0x10 | r2, r1, val); - -+exit: - mutex_unlock(&bus->mdio_lock); - } - -@@ -185,12 +200,16 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r - - mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- qca8k_set_page(bus, page); -+ ret = qca8k_set_page(bus, page); -+ if (ret < 0) -+ goto exit; -+ - ret = qca8k_mii_read32(bus, 0x10 | r2, r1); - ret &= ~mask; - ret |= val; - qca8k_mii_write32(bus, 0x10 | r2, r1, ret); - -+exit: - mutex_unlock(&bus->mdio_lock); - - return ret; diff --git a/target/linux/generic/backport-5.10/785-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch b/target/linux/generic/backport-5.10/785-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch deleted file mode 100644 index 3349b7897a..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-05-net-dsa-qca8k-handle-error-with-qca8k_read-operation.patch +++ /dev/null @@ -1,207 +0,0 @@ -From 028f5f8ef44fcf87a456772cbb9f0d90a0a22884 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:55 +0200 -Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_read operation - -qca8k_read can fail. Rework any user to handle error values and -correctly return. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 73 ++++++++++++++++++++++++++++++++--------- - 1 file changed, 58 insertions(+), 15 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -231,8 +231,13 @@ static int - qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ctx; -+ int ret; -+ -+ ret = qca8k_read(priv, reg); -+ if (ret < 0) -+ return ret; - -- *val = qca8k_read(priv, reg); -+ *val = ret; - - return 0; - } -@@ -300,15 +305,20 @@ qca8k_busy_wait(struct qca8k_priv *priv, - return ret; - } - --static void -+static int - qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) - { -- u32 reg[4]; -+ u32 reg[4], val; - int i; - - /* load the ARL table into an array */ -- for (i = 0; i < 4; i++) -- reg[i] = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); -+ for (i = 0; i < 4; i++) { -+ val = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); -+ if (val < 0) -+ return val; -+ -+ reg[i] = val; -+ } - - /* vid - 83:72 */ - fdb->vid = (reg[2] >> QCA8K_ATU_VID_S) & QCA8K_ATU_VID_M; -@@ -323,6 +333,8 @@ qca8k_fdb_read(struct qca8k_priv *priv, - fdb->mac[3] = (reg[0] >> QCA8K_ATU_ADDR3_S) & 0xff; - fdb->mac[4] = (reg[0] >> QCA8K_ATU_ADDR4_S) & 0xff; - fdb->mac[5] = reg[0] & 0xff; -+ -+ return 0; - } - - static void -@@ -374,6 +386,8 @@ qca8k_fdb_access(struct qca8k_priv *priv - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_FDB_LOAD) { - reg = qca8k_read(priv, QCA8K_REG_ATU_FUNC); -+ if (reg < 0) -+ return reg; - if (reg & QCA8K_ATU_FUNC_FULL) - return -1; - } -@@ -388,10 +402,10 @@ qca8k_fdb_next(struct qca8k_priv *priv, - - qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging); - ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port); -- if (ret >= 0) -- qca8k_fdb_read(priv, fdb); -+ if (ret < 0) -+ return ret; - -- return ret; -+ return qca8k_fdb_read(priv, fdb); - } - - static int -@@ -449,6 +463,8 @@ qca8k_vlan_access(struct qca8k_priv *pri - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_VLAN_LOAD) { - reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1); -+ if (reg < 0) -+ return reg; - if (reg & QCA8K_VTU_FUNC1_FULL) - return -ENOMEM; - } -@@ -475,6 +491,8 @@ qca8k_vlan_add(struct qca8k_priv *priv, - goto out; - - reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -+ if (reg < 0) -+ return reg; - reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; - reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - if (untagged) -@@ -506,6 +524,8 @@ qca8k_vlan_del(struct qca8k_priv *priv, - goto out; - - reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -+ if (reg < 0) -+ return reg; - reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << - QCA8K_VTU_FUNC0_EG_MODE_S(port); -@@ -621,8 +641,11 @@ qca8k_mdio_read(struct qca8k_priv *priv, - QCA8K_MDIO_MASTER_BUSY)) - return -ETIMEDOUT; - -- val = (qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL) & -- QCA8K_MDIO_MASTER_DATA_MASK); -+ val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); -+ if (val < 0) -+ return val; -+ -+ val &= QCA8K_MDIO_MASTER_DATA_MASK; - - return val; - } -@@ -978,6 +1001,8 @@ qca8k_phylink_mac_link_state(struct dsa_ - u32 reg; - - reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port)); -+ if (reg < 0) -+ return reg; - - state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); - state->an_complete = state->link; -@@ -1078,18 +1103,26 @@ qca8k_get_ethtool_stats(struct dsa_switc - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - const struct qca8k_mib_desc *mib; -- u32 reg, i; -+ u32 reg, i, val; - u64 hi; - - for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { - mib = &ar8327_mib[i]; - reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; - -- data[i] = qca8k_read(priv, reg); -+ val = qca8k_read(priv, reg); -+ if (val < 0) -+ continue; -+ - if (mib->size == 2) { - hi = qca8k_read(priv, reg + 4); -- data[i] |= hi << 32; -+ if (hi < 0) -+ continue; - } -+ -+ data[i] = val; -+ if (mib->size == 2) -+ data[i] |= hi << 32; - } - } - -@@ -1107,18 +1140,25 @@ qca8k_set_mac_eee(struct dsa_switch *ds, - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); -+ int ret = 0; - u32 reg; - - mutex_lock(&priv->reg_mutex); - reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); -+ if (reg < 0) { -+ ret = reg; -+ goto exit; -+ } -+ - if (eee->eee_enabled) - reg |= lpi_en; - else - reg &= ~lpi_en; - qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); -- mutex_unlock(&priv->reg_mutex); - -- return 0; -+exit: -+ mutex_unlock(&priv->reg_mutex); -+ return ret; - } - - static int -@@ -1456,6 +1496,9 @@ qca8k_sw_probe(struct mdio_device *mdiod - - /* read the switches ID register */ - id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); -+ if (id < 0) -+ return id; -+ - id >>= QCA8K_MASK_CTRL_ID_S; - id &= QCA8K_MASK_CTRL_ID_M; - if (id != QCA8K_ID_QCA8337) diff --git a/target/linux/generic/backport-5.10/785-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch b/target/linux/generic/backport-5.10/785-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch deleted file mode 100644 index 1e0e224c39..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-06-net-dsa-qca8k-handle-error-with-qca8k_write-operatio.patch +++ /dev/null @@ -1,263 +0,0 @@ -From d7805757c75c76e9518fc1023a29f0c4eed5b581 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:56 +0200 -Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_write operation - -qca8k_write can fail. Rework any user to handle error values and -correctly return. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 102 ++++++++++++++++++++++++++-------------- - 1 file changed, 67 insertions(+), 35 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -168,7 +168,7 @@ exit: - return val; - } - --static void -+static int - qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) - { - struct mii_bus *bus = priv->bus; -@@ -187,6 +187,7 @@ qca8k_write(struct qca8k_priv *priv, u32 - - exit: - mutex_unlock(&bus->mdio_lock); -+ return ret; - } - - static u32 -@@ -247,9 +248,7 @@ qca8k_regmap_write(void *ctx, uint32_t r - { - struct qca8k_priv *priv = (struct qca8k_priv *)ctx; - -- qca8k_write(priv, reg, val); -- -- return 0; -+ return qca8k_write(priv, reg, val); - } - - static const struct regmap_range qca8k_readable_ranges[] = { -@@ -367,6 +366,7 @@ static int - qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port) - { - u32 reg; -+ int ret; - - /* Set the command and FDB index */ - reg = QCA8K_ATU_FUNC_BUSY; -@@ -377,7 +377,9 @@ qca8k_fdb_access(struct qca8k_priv *priv - } - - /* Write the function register triggering the table access */ -- qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); -+ ret = qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); -+ if (ret) -+ return ret; - - /* wait for completion */ - if (qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY)) -@@ -447,6 +449,7 @@ static int - qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid) - { - u32 reg; -+ int ret; - - /* Set the command and VLAN index */ - reg = QCA8K_VTU_FUNC1_BUSY; -@@ -454,7 +457,9 @@ qca8k_vlan_access(struct qca8k_priv *pri - reg |= vid << QCA8K_VTU_FUNC1_VID_S; - - /* Write the function register triggering the table access */ -- qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); -+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); -+ if (ret) -+ return ret; - - /* wait for completion */ - if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY)) -@@ -502,7 +507,9 @@ qca8k_vlan_add(struct qca8k_priv *priv, - reg |= QCA8K_VTU_FUNC0_EG_MODE_TAG << - QCA8K_VTU_FUNC0_EG_MODE_S(port); - -- qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); -+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); -+ if (ret) -+ return ret; - ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); - - out: -@@ -545,7 +552,9 @@ qca8k_vlan_del(struct qca8k_priv *priv, - if (del) { - ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid); - } else { -- qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); -+ ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); -+ if (ret) -+ return ret; - ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); - } - -@@ -555,15 +564,20 @@ out: - return ret; - } - --static void -+static int - qca8k_mib_init(struct qca8k_priv *priv) - { -+ int ret; -+ - mutex_lock(&priv->reg_mutex); - qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); - qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); - qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); -- qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); -+ -+ ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); -+ - mutex_unlock(&priv->reg_mutex); -+ return ret; - } - - static void -@@ -600,6 +614,7 @@ static int - qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) - { - u32 phy, val; -+ int ret; - - if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) - return -EINVAL; -@@ -613,7 +628,9 @@ qca8k_mdio_write(struct qca8k_priv *priv - QCA8K_MDIO_MASTER_REG_ADDR(regnum) | - QCA8K_MDIO_MASTER_DATA(data); - -- qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -+ ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -+ if (ret) -+ return ret; - - return qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY); -@@ -623,6 +640,7 @@ static int - qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) - { - u32 phy, val; -+ int ret; - - if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) - return -EINVAL; -@@ -635,7 +653,9 @@ qca8k_mdio_read(struct qca8k_priv *priv, - QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | - QCA8K_MDIO_MASTER_REG_ADDR(regnum); - -- qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -+ ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -+ if (ret) -+ return ret; - - if (qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY)) -@@ -766,12 +786,18 @@ qca8k_setup(struct dsa_switch *ds) - QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); - - /* Enable MIB counters */ -- qca8k_mib_init(priv); -+ ret = qca8k_mib_init(priv); -+ if (ret) -+ dev_warn(priv->dev, "mib init failed"); - - /* Enable QCA header mode on the cpu port */ -- qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), -- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | -- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); -+ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), -+ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | -+ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); -+ if (ret) { -+ dev_err(priv->dev, "failed enabling QCA header mode"); -+ return ret; -+ } - - /* Disable forwarding by default on all ports */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) -@@ -783,11 +809,13 @@ qca8k_setup(struct dsa_switch *ds) - qca8k_port_set_status(priv, i, 0); - - /* Forward all unknown frames to CPU port for Linux processing */ -- qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); -+ ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, -+ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | -+ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | -+ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | -+ BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); -+ if (ret) -+ return ret; - - /* Setup connection between CPU port & user ports */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) { -@@ -815,16 +843,20 @@ qca8k_setup(struct dsa_switch *ds) - qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), - 0xfff << shift, - QCA8K_PORT_VID_DEF << shift); -- qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), -- QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | -- QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); -+ ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), -+ QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | -+ QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); -+ if (ret) -+ return ret; - } - } - - /* Setup our port MTUs to match power on defaults */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) - priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; -- qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); -+ ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); -+ if (ret) -+ dev_warn(priv->dev, "failed setting MTU settings"); - - /* Flush the FDB table */ - qca8k_fdb_flush(priv); -@@ -1140,8 +1172,8 @@ qca8k_set_mac_eee(struct dsa_switch *ds, - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); -- int ret = 0; - u32 reg; -+ int ret; - - mutex_lock(&priv->reg_mutex); - reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); -@@ -1154,7 +1186,7 @@ qca8k_set_mac_eee(struct dsa_switch *ds, - reg |= lpi_en; - else - reg &= ~lpi_en; -- qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); -+ ret = qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); - - exit: - mutex_unlock(&priv->reg_mutex); -@@ -1284,9 +1316,7 @@ qca8k_port_change_mtu(struct dsa_switch - mtu = priv->port_mtu[i]; - - /* Include L2 header / FCS length */ -- qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); -- -- return 0; -+ return qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); - } - - static int diff --git a/target/linux/generic/backport-5.10/785-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch b/target/linux/generic/backport-5.10/785-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch deleted file mode 100644 index 506966f1af..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-07-net-dsa-qca8k-handle-error-with-qca8k_rmw-operation.patch +++ /dev/null @@ -1,226 +0,0 @@ -From aaf421425cbdec4eb6fd75a29e65c2867b0b7bbd Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:57 +0200 -Subject: [PATCH] net: dsa: qca8k: handle error with qca8k_rmw operation - -qca8k_rmw can fail. Rework any user to handle error values and -correctly return. Change qca8k_rmw to return the error code or 0 instead -of the reg value. The reg returned by qca8k_rmw wasn't used anywhere, -so this doesn't cause any functional change. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 133 +++++++++++++++++++++++++--------------- - 1 file changed, 83 insertions(+), 50 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -190,12 +190,13 @@ exit: - return ret; - } - --static u32 --qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 val) -+static int -+qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val) - { - struct mii_bus *bus = priv->bus; - u16 r1, r2, page; -- u32 ret; -+ u32 val; -+ int ret; - - qca8k_split_addr(reg, &r1, &r2, &page); - -@@ -205,10 +206,15 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r - if (ret < 0) - goto exit; - -- ret = qca8k_mii_read32(bus, 0x10 | r2, r1); -- ret &= ~mask; -- ret |= val; -- qca8k_mii_write32(bus, 0x10 | r2, r1, ret); -+ val = qca8k_mii_read32(bus, 0x10 | r2, r1); -+ if (val < 0) { -+ ret = val; -+ goto exit; -+ } -+ -+ val &= ~mask; -+ val |= write_val; -+ qca8k_mii_write32(bus, 0x10 | r2, r1, val); - - exit: - mutex_unlock(&bus->mdio_lock); -@@ -216,16 +222,16 @@ exit: - return ret; - } - --static void -+static int - qca8k_reg_set(struct qca8k_priv *priv, u32 reg, u32 val) - { -- qca8k_rmw(priv, reg, 0, val); -+ return qca8k_rmw(priv, reg, 0, val); - } - --static void -+static int - qca8k_reg_clear(struct qca8k_priv *priv, u32 reg, u32 val) - { -- qca8k_rmw(priv, reg, val, 0); -+ return qca8k_rmw(priv, reg, val, 0); - } - - static int -@@ -570,12 +576,19 @@ qca8k_mib_init(struct qca8k_priv *priv) - int ret; - - mutex_lock(&priv->reg_mutex); -- qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); -+ ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); -+ if (ret) -+ goto exit; -+ - qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); -- qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); -+ -+ ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); -+ if (ret) -+ goto exit; - - ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); - -+exit: - mutex_unlock(&priv->reg_mutex); - return ret; - } -@@ -747,9 +760,8 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - * a dt-overlay and driver reload changed the configuration - */ - -- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_EN); -- return 0; -+ return qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_EN); - } - - priv->ops.phy_read = qca8k_phy_read; -@@ -782,8 +794,12 @@ qca8k_setup(struct dsa_switch *ds) - return ret; - - /* Enable CPU Port */ -- qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, -- QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); -+ ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, -+ QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); -+ if (ret) { -+ dev_err(priv->dev, "failed enabling CPU port"); -+ return ret; -+ } - - /* Enable MIB counters */ - ret = qca8k_mib_init(priv); -@@ -800,9 +816,12 @@ qca8k_setup(struct dsa_switch *ds) - } - - /* Disable forwarding by default on all ports */ -- for (i = 0; i < QCA8K_NUM_PORTS; i++) -- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), -- QCA8K_PORT_LOOKUP_MEMBER, 0); -+ for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), -+ QCA8K_PORT_LOOKUP_MEMBER, 0); -+ if (ret) -+ return ret; -+ } - - /* Disable MAC by default on all ports */ - for (i = 1; i < QCA8K_NUM_PORTS; i++) -@@ -821,28 +840,37 @@ qca8k_setup(struct dsa_switch *ds) - for (i = 0; i < QCA8K_NUM_PORTS; i++) { - /* CPU port gets connected to all user ports of the switch */ - if (dsa_is_cpu_port(ds, i)) { -- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), -- QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), -+ QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); -+ if (ret) -+ return ret; - } - - /* Individual user ports get connected to CPU port only */ - if (dsa_is_user_port(ds, i)) { - int shift = 16 * (i % 2); - -- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), -- QCA8K_PORT_LOOKUP_MEMBER, -- BIT(QCA8K_CPU_PORT)); -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), -+ QCA8K_PORT_LOOKUP_MEMBER, -+ BIT(QCA8K_CPU_PORT)); -+ if (ret) -+ return ret; - - /* Enable ARP Auto-learning by default */ -- qca8k_reg_set(priv, QCA8K_PORT_LOOKUP_CTRL(i), -- QCA8K_PORT_LOOKUP_LEARN); -+ ret = qca8k_reg_set(priv, QCA8K_PORT_LOOKUP_CTRL(i), -+ QCA8K_PORT_LOOKUP_LEARN); -+ if (ret) -+ return ret; - - /* For port based vlans to work we need to set the - * default egress vid - */ -- qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), -- 0xfff << shift, -- QCA8K_PORT_VID_DEF << shift); -+ ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), -+ 0xfff << shift, -+ QCA8K_PORT_VID_DEF << shift); -+ if (ret) -+ return ret; -+ - ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), - QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | - QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); -@@ -1234,7 +1262,7 @@ qca8k_port_bridge_join(struct dsa_switch - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - int port_mask = BIT(QCA8K_CPU_PORT); -- int i; -+ int i, ret; - - for (i = 1; i < QCA8K_NUM_PORTS; i++) { - if (dsa_to_port(ds, i)->bridge_dev != br) -@@ -1242,17 +1270,20 @@ qca8k_port_bridge_join(struct dsa_switch - /* Add this port to the portvlan mask of the other ports - * in the bridge - */ -- qca8k_reg_set(priv, -- QCA8K_PORT_LOOKUP_CTRL(i), -- BIT(port)); -+ ret = qca8k_reg_set(priv, -+ QCA8K_PORT_LOOKUP_CTRL(i), -+ BIT(port)); -+ if (ret) -+ return ret; - if (i != port) - port_mask |= BIT(i); - } -+ - /* Add all other ports to this ports portvlan mask */ -- qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), -- QCA8K_PORT_LOOKUP_MEMBER, port_mask); -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), -+ QCA8K_PORT_LOOKUP_MEMBER, port_mask); - -- return 0; -+ return ret; - } - - static void diff --git a/target/linux/generic/backport-5.10/785-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch b/target/linux/generic/backport-5.10/785-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch deleted file mode 100644 index 360ce1d947..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-08-net-dsa-qca8k-handle-error-from-qca8k_busy_wait.patch +++ /dev/null @@ -1,66 +0,0 @@ -From b7c818d194927bdc60ed15db55bb8654496a36b7 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:58 +0200 -Subject: [PATCH] net: dsa: qca8k: handle error from qca8k_busy_wait - -Propagate errors from qca8k_busy_wait instead of hardcoding return -value. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 21 +++++++++++++-------- - 1 file changed, 13 insertions(+), 8 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -388,8 +388,9 @@ qca8k_fdb_access(struct qca8k_priv *priv - return ret; - - /* wait for completion */ -- if (qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY)) -- return -1; -+ ret = qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY); -+ if (ret) -+ return ret; - - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_FDB_LOAD) { -@@ -468,8 +469,9 @@ qca8k_vlan_access(struct qca8k_priv *pri - return ret; - - /* wait for completion */ -- if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY)) -- return -ETIMEDOUT; -+ ret = qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY); -+ if (ret) -+ return ret; - - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_VLAN_LOAD) { -@@ -580,7 +582,9 @@ qca8k_mib_init(struct qca8k_priv *priv) - if (ret) - goto exit; - -- qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); -+ ret = qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); -+ if (ret) -+ goto exit; - - ret = qca8k_reg_set(priv, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); - if (ret) -@@ -670,9 +674,10 @@ qca8k_mdio_read(struct qca8k_priv *priv, - if (ret) - return ret; - -- if (qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_BUSY)) -- return -ETIMEDOUT; -+ ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_BUSY); -+ if (ret) -+ return ret; - - val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); - if (val < 0) diff --git a/target/linux/generic/backport-5.10/785-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch b/target/linux/generic/backport-5.10/785-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch deleted file mode 100644 index 72305850ca..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-09-net-dsa-qca8k-add-support-for-qca8327-switch.patch +++ /dev/null @@ -1,96 +0,0 @@ -From 6e82a457e06252b59102486767539cc9c2aba60b Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 22:59:59 +0200 -Subject: [PATCH] net: dsa: qca8k: add support for qca8327 switch - -qca8327 switch is a low tier version of the more recent qca8337. -It does share the same regs used by the qca8k driver and can be -supported with minimal change. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Reviewed-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 23 ++++++++++++++++++++--- - drivers/net/dsa/qca8k.h | 6 ++++++ - 2 files changed, 26 insertions(+), 3 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1533,6 +1533,7 @@ static const struct dsa_switch_ops qca8k - static int - qca8k_sw_probe(struct mdio_device *mdiodev) - { -+ const struct qca8k_match_data *data; - struct qca8k_priv *priv; - u32 id; - -@@ -1560,6 +1561,11 @@ qca8k_sw_probe(struct mdio_device *mdiod - gpiod_set_value_cansleep(priv->reset_gpio, 0); - } - -+ /* get the switches ID from the compatible */ -+ data = of_device_get_match_data(&mdiodev->dev); -+ if (!data) -+ return -ENODEV; -+ - /* read the switches ID register */ - id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); - if (id < 0) -@@ -1567,8 +1573,10 @@ qca8k_sw_probe(struct mdio_device *mdiod - - id >>= QCA8K_MASK_CTRL_ID_S; - id &= QCA8K_MASK_CTRL_ID_M; -- if (id != QCA8K_ID_QCA8337) -+ if (id != data->id) { -+ dev_err(&mdiodev->dev, "Switch id detected %x but expected %x", id, data->id); - return -ENODEV; -+ } - - priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); - if (!priv->ds) -@@ -1634,9 +1642,18 @@ static int qca8k_resume(struct device *d - static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, - qca8k_suspend, qca8k_resume); - -+static const struct qca8k_match_data qca832x = { -+ .id = QCA8K_ID_QCA8327, -+}; -+ -+static const struct qca8k_match_data qca833x = { -+ .id = QCA8K_ID_QCA8337, -+}; -+ - static const struct of_device_id qca8k_of_match[] = { -- { .compatible = "qca,qca8334" }, -- { .compatible = "qca,qca8337" }, -+ { .compatible = "qca,qca8327", .data = &qca832x }, -+ { .compatible = "qca,qca8334", .data = &qca833x }, -+ { .compatible = "qca,qca8337", .data = &qca833x }, - { /* sentinel */ }, - }; - ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -15,6 +15,8 @@ - #define QCA8K_NUM_PORTS 7 - #define QCA8K_MAX_MTU 9000 - -+#define PHY_ID_QCA8327 0x004dd034 -+#define QCA8K_ID_QCA8327 0x12 - #define PHY_ID_QCA8337 0x004dd036 - #define QCA8K_ID_QCA8337 0x13 - -@@ -213,6 +215,10 @@ struct ar8xxx_port_status { - int enabled; - }; - -+struct qca8k_match_data { -+ u8 id; -+}; -+ - struct qca8k_priv { - struct regmap *regmap; - struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/785-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch b/target/linux/generic/backport-5.10/785-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch deleted file mode 100644 index 3c4a14bd0b..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-10-devicetree-net-dsa-qca8k-Document-new-compatible-qca.patch +++ /dev/null @@ -1,26 +0,0 @@ -From 227a9ffc1bc77037339530607fe129af3824620e Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:00 +0200 -Subject: [PATCH] devicetree: net: dsa: qca8k: Document new compatible qca8327 - -Add support for qca8327 in the compatible list. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Acked-by: Rob Herring -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 1 + - 1 file changed, 1 insertion(+) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -3,6 +3,7 @@ - Required properties: - - - compatible: should be one of: -+ "qca,qca8327" - "qca,qca8334" - "qca,qca8337" - diff --git a/target/linux/generic/backport-5.10/785-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch b/target/linux/generic/backport-5.10/785-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch deleted file mode 100644 index cd3050ef71..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-11-net-dsa-qca8k-add-priority-tweak-to-qca8337-switch.patch +++ /dev/null @@ -1,130 +0,0 @@ -From 83a3ceb39b2495171aabe9446271b94c678354f3 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:01 +0200 -Subject: [PATCH] net: dsa: qca8k: add priority tweak to qca8337 switch - -The port 5 of the qca8337 have some problem in flood condition. The -original legacy driver had some specific buffer and priority settings -for the different port suggested by the QCA switch team. Add this -missing settings to improve switch stability under load condition. -The packet priority tweak is only needed for the qca8337 switch and -other qca8k switch are not affected. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 47 +++++++++++++++++++++++++++++++++++++++++ - drivers/net/dsa/qca8k.h | 25 ++++++++++++++++++++++ - 2 files changed, 72 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -779,6 +779,7 @@ qca8k_setup(struct dsa_switch *ds) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - int ret, i; -+ u32 mask; - - /* Make sure that port 0 is the cpu port */ - if (!dsa_is_cpu_port(ds, 0)) { -@@ -884,6 +885,51 @@ qca8k_setup(struct dsa_switch *ds) - } - } - -+ /* The port 5 of the qca8337 have some problem in flood condition. The -+ * original legacy driver had some specific buffer and priority settings -+ * for the different port suggested by the QCA switch team. Add this -+ * missing settings to improve switch stability under load condition. -+ * This problem is limited to qca8337 and other qca8k switch are not affected. -+ */ -+ if (priv->switch_id == QCA8K_ID_QCA8337) { -+ for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ switch (i) { -+ /* The 2 CPU port and port 5 requires some different -+ * priority than any other ports. -+ */ -+ case 0: -+ case 5: -+ case 6: -+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) | -+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e); -+ break; -+ default: -+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) | -+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) | -+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19); -+ } -+ qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask); -+ -+ mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) | -+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | -+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | -+ QCA8K_PORT_HOL_CTRL1_WRED_EN; -+ qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i), -+ QCA8K_PORT_HOL_CTRL1_ING_BUF | -+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | -+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | -+ QCA8K_PORT_HOL_CTRL1_WRED_EN, -+ mask); -+ } -+ } -+ - /* Setup our port MTUs to match power on defaults */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) - priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; -@@ -1578,6 +1624,7 @@ qca8k_sw_probe(struct mdio_device *mdiod - return -ENODEV; - } - -+ priv->switch_id = id; - priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); - if (!priv->ds) - return -ENOMEM; ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -168,6 +168,30 @@ - #define QCA8K_PORT_LOOKUP_STATE GENMASK(18, 16) - #define QCA8K_PORT_LOOKUP_LEARN BIT(20) - -+#define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF GENMASK(3, 0) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) ((x) << 0) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF GENMASK(7, 4) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1(x) ((x) << 4) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF GENMASK(11, 8) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2(x) ((x) << 8) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF GENMASK(15, 12) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3(x) ((x) << 12) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF GENMASK(19, 16) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4(x) ((x) << 16) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF GENMASK(23, 20) -+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5(x) ((x) << 20) -+#define QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF GENMASK(29, 24) -+#define QCA8K_PORT_HOL_CTRL0_EG_PORT(x) ((x) << 24) -+ -+#define QCA8K_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8) -+#define QCA8K_PORT_HOL_CTRL1_ING_BUF GENMASK(3, 0) -+#define QCA8K_PORT_HOL_CTRL1_ING(x) ((x) << 0) -+#define QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6) -+#define QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7) -+#define QCA8K_PORT_HOL_CTRL1_WRED_EN BIT(8) -+#define QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16) -+ - /* Pkt edit registers */ - #define QCA8K_EGRESS_VLAN(x) (0x0c70 + (4 * (x / 2))) - -@@ -220,6 +244,7 @@ struct qca8k_match_data { - }; - - struct qca8k_priv { -+ u8 switch_id; - struct regmap *regmap; - struct mii_bus *bus; - struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/785-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch b/target/linux/generic/backport-5.10/785-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch deleted file mode 100644 index d25edbb1aa..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-12-net-dsa-qca8k-limit-port5-delay-to-qca8337.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 5bf9ff3b9fb5ecb67a1a3517b26db3a00f2a2f11 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:02 +0200 -Subject: [PATCH] net: dsa: qca8k: limit port5 delay to qca8337 - -Limit port5 rx delay to qca8337. This is taken from the legacy QSDK code -that limits the rx delay on port5 to only this particular switch version, -on other switch only the tx and rx delay for port0 are needed. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 6 ++++-- - 1 file changed, 4 insertions(+), 2 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1003,8 +1003,10 @@ qca8k_phylink_mac_config(struct dsa_swit - QCA8K_PORT_PAD_RGMII_EN | - QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) | - QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY)); -- qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, -- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); -+ /* QCA8337 requires to set rgmii rx delay */ -+ if (priv->switch_id == QCA8K_ID_QCA8337) -+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); - break; - case PHY_INTERFACE_MODE_SGMII: - case PHY_INTERFACE_MODE_1000BASEX: diff --git a/target/linux/generic/backport-5.10/785-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch b/target/linux/generic/backport-5.10/785-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch deleted file mode 100644 index 2b393d242a..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-13-net-dsa-qca8k-add-GLOBAL_FC-settings-needed-for-qca8.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 0fc57e4b5e39461fc0a54aae0afe4241363a7267 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:03 +0200 -Subject: [PATCH] net: dsa: qca8k: add GLOBAL_FC settings needed for qca8327 - -Switch qca8327 needs special settings for the GLOBAL_FC_THRES regs. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 10 ++++++++++ - drivers/net/dsa/qca8k.h | 6 ++++++ - 2 files changed, 16 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -930,6 +930,16 @@ qca8k_setup(struct dsa_switch *ds) - } - } - -+ /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ -+ if (priv->switch_id == QCA8K_ID_QCA8327) { -+ mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) | -+ QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496); -+ qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH, -+ QCA8K_GLOBAL_FC_GOL_XON_THRES_S | -+ QCA8K_GLOBAL_FC_GOL_XOFF_THRES_S, -+ mask); -+ } -+ - /* Setup our port MTUs to match power on defaults */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) - priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -168,6 +168,12 @@ - #define QCA8K_PORT_LOOKUP_STATE GENMASK(18, 16) - #define QCA8K_PORT_LOOKUP_LEARN BIT(20) - -+#define QCA8K_REG_GLOBAL_FC_THRESH 0x800 -+#define QCA8K_GLOBAL_FC_GOL_XON_THRES(x) ((x) << 16) -+#define QCA8K_GLOBAL_FC_GOL_XON_THRES_S GENMASK(24, 16) -+#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES(x) ((x) << 0) -+#define QCA8K_GLOBAL_FC_GOL_XOFF_THRES_S GENMASK(8, 0) -+ - #define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8) - #define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF GENMASK(3, 0) - #define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) ((x) << 0) diff --git a/target/linux/generic/backport-5.10/785-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch b/target/linux/generic/backport-5.10/785-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch deleted file mode 100644 index ed9b8188de..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-14-net-dsa-qca8k-add-support-for-switch-rev.patch +++ /dev/null @@ -1,114 +0,0 @@ -From 95ffeaf18b3bb90eeef52cbf7d79ccc9d0345ff5 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:04 +0200 -Subject: [PATCH] net: dsa: qca8k: add support for switch rev - -qca8k internal phy driver require some special debug value to be set -based on the switch revision. Rework the switch id read function to -also read the chip revision. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 53 ++++++++++++++++++++++++++--------------- - drivers/net/dsa/qca8k.h | 7 ++++-- - 2 files changed, 39 insertions(+), 21 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1588,12 +1588,40 @@ static const struct dsa_switch_ops qca8k - .phylink_mac_link_up = qca8k_phylink_mac_link_up, - }; - -+static int qca8k_read_switch_id(struct qca8k_priv *priv) -+{ -+ const struct qca8k_match_data *data; -+ u32 val; -+ u8 id; -+ -+ /* get the switches ID from the compatible */ -+ data = of_device_get_match_data(priv->dev); -+ if (!data) -+ return -ENODEV; -+ -+ val = qca8k_read(priv, QCA8K_REG_MASK_CTRL); -+ if (val < 0) -+ return -ENODEV; -+ -+ id = QCA8K_MASK_CTRL_DEVICE_ID(val & QCA8K_MASK_CTRL_DEVICE_ID_MASK); -+ if (id != data->id) { -+ dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id); -+ return -ENODEV; -+ } -+ -+ priv->switch_id = id; -+ -+ /* Save revision to communicate to the internal PHY driver */ -+ priv->switch_revision = (val & QCA8K_MASK_CTRL_REV_ID_MASK); -+ -+ return 0; -+} -+ - static int - qca8k_sw_probe(struct mdio_device *mdiodev) - { -- const struct qca8k_match_data *data; - struct qca8k_priv *priv; -- u32 id; -+ int ret; - - /* allocate the private data struct so that we can probe the switches - * ID register -@@ -1619,24 +1647,11 @@ qca8k_sw_probe(struct mdio_device *mdiod - gpiod_set_value_cansleep(priv->reset_gpio, 0); - } - -- /* get the switches ID from the compatible */ -- data = of_device_get_match_data(&mdiodev->dev); -- if (!data) -- return -ENODEV; -+ /* Check the detected switch id */ -+ ret = qca8k_read_switch_id(priv); -+ if (ret) -+ return ret; - -- /* read the switches ID register */ -- id = qca8k_read(priv, QCA8K_REG_MASK_CTRL); -- if (id < 0) -- return id; -- -- id >>= QCA8K_MASK_CTRL_ID_S; -- id &= QCA8K_MASK_CTRL_ID_M; -- if (id != data->id) { -- dev_err(&mdiodev->dev, "Switch id detected %x but expected %x", id, data->id); -- return -ENODEV; -- } -- -- priv->switch_id = id; - priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); - if (!priv->ds) - return -ENOMEM; ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -30,8 +30,10 @@ - - /* Global control registers */ - #define QCA8K_REG_MASK_CTRL 0x000 --#define QCA8K_MASK_CTRL_ID_M 0xff --#define QCA8K_MASK_CTRL_ID_S 8 -+#define QCA8K_MASK_CTRL_REV_ID_MASK GENMASK(7, 0) -+#define QCA8K_MASK_CTRL_REV_ID(x) ((x) >> 0) -+#define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8) -+#define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8) - #define QCA8K_REG_PORT0_PAD_CTRL 0x004 - #define QCA8K_REG_PORT5_PAD_CTRL 0x008 - #define QCA8K_REG_PORT6_PAD_CTRL 0x00c -@@ -251,6 +253,7 @@ struct qca8k_match_data { - - struct qca8k_priv { - u8 switch_id; -+ u8 switch_revision; - struct regmap *regmap; - struct mii_bus *bus; - struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/785-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch b/target/linux/generic/backport-5.10/785-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch deleted file mode 100644 index 629cb324e0..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-15-net-dsa-qca8k-add-ethernet-ports-fallback-to-setup_m.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 1ee0591a1093c2448642c33433483e9260275f7b Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:05 +0200 -Subject: [PATCH] net: dsa: qca8k: add ethernet-ports fallback to - setup_mdio_bus - -Dsa now also supports ethernet-ports. Add this new binding as a fallback -if the ports node can't be found. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -719,6 +719,9 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - - ports = of_get_child_by_name(priv->dev->of_node, "ports"); - if (!ports) -+ ports = of_get_child_by_name(priv->dev->of_node, "ethernet-ports"); -+ -+ if (!ports) - return -EINVAL; - - for_each_available_child_of_node(ports, port) { diff --git a/target/linux/generic/backport-5.10/785-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch b/target/linux/generic/backport-5.10/785-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch deleted file mode 100644 index 6dc2dc6e3e..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-16-net-dsa-qca8k-make-rgmii-delay-configurable.patch +++ /dev/null @@ -1,188 +0,0 @@ -From e4b9977cee1583da38a6e9118078bb728aaccf7b Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:06 +0200 -Subject: [PATCH] net: dsa: qca8k: make rgmii delay configurable - -The legacy qsdk code used a different delay instead of the max value. -Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable -using the standard rx/tx-internal-delay-ps ethernet binding and apply -qsdk values by default. The connected gmac doesn't add any delay so no -additional delay is added to tx/rx. -On this switch the delay is actually in ns so value should be in the -1000 order. Any value converted from ps to ns by dividing it by 1000 -as the switch max value for delay is 3ns. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 82 ++++++++++++++++++++++++++++++++++++++++- - drivers/net/dsa/qca8k.h | 11 +++--- - 2 files changed, 86 insertions(+), 7 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -778,6 +778,68 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - } - - static int -+qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv) -+{ -+ struct device_node *port_dn; -+ phy_interface_t mode; -+ struct dsa_port *dp; -+ u32 val; -+ -+ /* CPU port is already checked */ -+ dp = dsa_to_port(priv->ds, 0); -+ -+ port_dn = dp->dn; -+ -+ /* Check if port 0 is set to the correct type */ -+ of_get_phy_mode(port_dn, &mode); -+ if (mode != PHY_INTERFACE_MODE_RGMII_ID && -+ mode != PHY_INTERFACE_MODE_RGMII_RXID && -+ mode != PHY_INTERFACE_MODE_RGMII_TXID) { -+ return 0; -+ } -+ -+ switch (mode) { -+ case PHY_INTERFACE_MODE_RGMII_ID: -+ case PHY_INTERFACE_MODE_RGMII_RXID: -+ if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val)) -+ val = 2; -+ else -+ /* Switch regs accept value in ns, convert ps to ns */ -+ val = val / 1000; -+ -+ if (val > QCA8K_MAX_DELAY) { -+ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); -+ val = 3; -+ } -+ -+ priv->rgmii_rx_delay = val; -+ /* Stop here if we need to check only for rx delay */ -+ if (mode != PHY_INTERFACE_MODE_RGMII_ID) -+ break; -+ -+ fallthrough; -+ case PHY_INTERFACE_MODE_RGMII_TXID: -+ if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val)) -+ val = 1; -+ else -+ /* Switch regs accept value in ns, convert ps to ns */ -+ val = val / 1000; -+ -+ if (val > QCA8K_MAX_DELAY) { -+ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); -+ val = 3; -+ } -+ -+ priv->rgmii_tx_delay = val; -+ break; -+ default: -+ return 0; -+ } -+ -+ return 0; -+} -+ -+static int - qca8k_setup(struct dsa_switch *ds) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -@@ -802,6 +864,10 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - -+ ret = qca8k_setup_of_rgmii_delay(priv); -+ if (ret) -+ return ret; -+ - /* Enable CPU Port */ - ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, - QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); -@@ -970,6 +1036,8 @@ qca8k_phylink_mac_config(struct dsa_swit - case 0: /* 1st CPU port */ - if (state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_RGMII_ID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && - state->interface != PHY_INTERFACE_MODE_SGMII) - return; - -@@ -985,6 +1053,8 @@ qca8k_phylink_mac_config(struct dsa_swit - case 6: /* 2nd CPU port / external PHY */ - if (state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_RGMII_ID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && - state->interface != PHY_INTERFACE_MODE_SGMII && - state->interface != PHY_INTERFACE_MODE_1000BASEX) - return; -@@ -1008,14 +1078,18 @@ qca8k_phylink_mac_config(struct dsa_swit - qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); - break; - case PHY_INTERFACE_MODE_RGMII_ID: -+ case PHY_INTERFACE_MODE_RGMII_TXID: -+ case PHY_INTERFACE_MODE_RGMII_RXID: - /* RGMII_ID needs internal delay. This is enabled through - * PORT5_PAD_CTRL for all ports, rather than individual port - * registers - */ - qca8k_write(priv, reg, - QCA8K_PORT_PAD_RGMII_EN | -- QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) | -- QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY)); -+ QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) | -+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); - /* QCA8337 requires to set rgmii rx delay */ - if (priv->switch_id == QCA8K_ID_QCA8337) - qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, -@@ -1073,6 +1147,8 @@ qca8k_phylink_validate(struct dsa_switch - if (state->interface != PHY_INTERFACE_MODE_NA && - state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_RGMII_ID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && - state->interface != PHY_INTERFACE_MODE_SGMII) - goto unsupported; - break; -@@ -1090,6 +1166,8 @@ qca8k_phylink_validate(struct dsa_switch - if (state->interface != PHY_INTERFACE_MODE_NA && - state->interface != PHY_INTERFACE_MODE_RGMII && - state->interface != PHY_INTERFACE_MODE_RGMII_ID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_TXID && -+ state->interface != PHY_INTERFACE_MODE_RGMII_RXID && - state->interface != PHY_INTERFACE_MODE_SGMII && - state->interface != PHY_INTERFACE_MODE_1000BASEX) - goto unsupported; ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -38,12 +38,11 @@ - #define QCA8K_REG_PORT5_PAD_CTRL 0x008 - #define QCA8K_REG_PORT6_PAD_CTRL 0x00c - #define QCA8K_PORT_PAD_RGMII_EN BIT(26) --#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) \ -- ((0x8 + (x & 0x3)) << 22) --#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) \ -- ((0x10 + (x & 0x3)) << 20) --#define QCA8K_MAX_DELAY 3 -+#define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) ((x) << 22) -+#define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) ((x) << 20) -+#define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25) - #define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24) -+#define QCA8K_MAX_DELAY 3 - #define QCA8K_PORT_PAD_SGMII_EN BIT(7) - #define QCA8K_REG_PWS 0x010 - #define QCA8K_PWS_SERDES_AEN_DIS BIT(7) -@@ -254,6 +253,8 @@ struct qca8k_match_data { - struct qca8k_priv { - u8 switch_id; - u8 switch_revision; -+ u8 rgmii_tx_delay; -+ u8 rgmii_rx_delay; - struct regmap *regmap; - struct mii_bus *bus; - struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/785-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch b/target/linux/generic/backport-5.10/785-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch deleted file mode 100644 index 4593da032b..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-17-net-dsa-qca8k-clear-MASTER_EN-after-phy-read-write.patch +++ /dev/null @@ -1,50 +0,0 @@ -From 63c33bbfeb6842a956a0eb12901e28eb335bdb18 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:07 +0200 -Subject: [PATCH] net: dsa: qca8k: clear MASTER_EN after phy read/write - -Clear MDIO_MASTER_EN bit from MDIO_MASTER_CTRL after read/write -operation. The MDIO_MASTER_EN bit is not reset after read/write -operation and the next operation can be wrongly interpreted by the -switch as a mdio operation. This cause a production of wrong/garbage -data from the switch and underfined bheavior. (random port drop, -unplugged port flagged with link up, wrong port speed) -Also on driver remove the MASTER_CTRL can be left set and cause the -malfunction of any next driver using the mdio device. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 14 ++++++++++++-- - 1 file changed, 12 insertions(+), 2 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -649,8 +649,14 @@ qca8k_mdio_write(struct qca8k_priv *priv - if (ret) - return ret; - -- return qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_BUSY); -+ ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_BUSY); -+ -+ /* even if the busy_wait timeouts try to clear the MASTER_EN */ -+ qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_EN); -+ -+ return ret; - } - - static int -@@ -685,6 +691,10 @@ qca8k_mdio_read(struct qca8k_priv *priv, - - val &= QCA8K_MDIO_MASTER_DATA_MASK; - -+ /* even if the busy_wait timeouts try to clear the MASTER_EN */ -+ qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_EN); -+ - return val; - } - diff --git a/target/linux/generic/backport-5.10/785-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch b/target/linux/generic/backport-5.10/785-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch deleted file mode 100644 index b6684d7210..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-18-net-dsa-qca8k-dsa-qca8k-protect-MASTER-busy_wait-wit.patch +++ /dev/null @@ -1,128 +0,0 @@ -From 60df02b6ea4581d72eb7a3ab7204504a54059b72 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:08 +0200 -Subject: [PATCH] net: dsa: qca8k: dsa: qca8k: protect MASTER busy_wait with - mdio mutex - -MDIO_MASTER operation have a dedicated busy wait that is not protected -by the mdio mutex. This can cause situation where the MASTER operation -is done and a normal operation is executed between the MASTER read/write -and the MASTER busy_wait. Rework the qca8k_mdio_read/write function to -address this issue by binding the lock for the whole MASTER operation -and not only the mdio read/write common operation. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 68 +++++++++++++++++++++++++++++++++-------- - 1 file changed, 55 insertions(+), 13 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -628,8 +628,31 @@ qca8k_port_to_phy(int port) - } - - static int -+qca8k_mdio_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) -+{ -+ u16 r1, r2, page; -+ u32 val; -+ int ret; -+ -+ qca8k_split_addr(reg, &r1, &r2, &page); -+ -+ ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, -+ QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, -+ priv->bus, 0x10 | r2, r1); -+ -+ /* Check if qca8k_read has failed for a different reason -+ * before returnting -ETIMEDOUT -+ */ -+ if (ret < 0 && val < 0) -+ return val; -+ -+ return ret; -+} -+ -+static int - qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) - { -+ u16 r1, r2, page; - u32 phy, val; - int ret; - -@@ -645,12 +668,21 @@ qca8k_mdio_write(struct qca8k_priv *priv - QCA8K_MDIO_MASTER_REG_ADDR(regnum) | - QCA8K_MDIO_MASTER_DATA(data); - -- ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -+ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); -+ -+ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ -+ ret = qca8k_set_page(priv->bus, page); - if (ret) -- return ret; -+ goto exit; -+ -+ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); - -- ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_BUSY); -+ ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_BUSY); -+ -+exit: -+ mutex_unlock(&priv->bus->mdio_lock); - - /* even if the busy_wait timeouts try to clear the MASTER_EN */ - qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -@@ -662,6 +694,7 @@ qca8k_mdio_write(struct qca8k_priv *priv - static int - qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) - { -+ u16 r1, r2, page; - u32 phy, val; - int ret; - -@@ -676,21 +709,30 @@ qca8k_mdio_read(struct qca8k_priv *priv, - QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | - QCA8K_MDIO_MASTER_REG_ADDR(regnum); - -- ret = qca8k_write(priv, QCA8K_MDIO_MASTER_CTRL, val); -- if (ret) -- return ret; -+ qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); -+ -+ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); - -- ret = qca8k_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_BUSY); -+ ret = qca8k_set_page(priv->bus, page); - if (ret) -- return ret; -+ goto exit; - -- val = qca8k_read(priv, QCA8K_MDIO_MASTER_CTRL); -- if (val < 0) -- return val; -+ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); -+ -+ ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ QCA8K_MDIO_MASTER_BUSY); -+ if (ret) -+ goto exit; - -+ val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); - val &= QCA8K_MDIO_MASTER_DATA_MASK; - -+exit: -+ mutex_unlock(&priv->bus->mdio_lock); -+ -+ if (val >= 0) -+ val &= QCA8K_MDIO_MASTER_DATA_MASK; -+ - /* even if the busy_wait timeouts try to clear the MASTER_EN */ - qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_EN); diff --git a/target/linux/generic/backport-5.10/785-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch b/target/linux/generic/backport-5.10/785-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch deleted file mode 100644 index 30eeed361e..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-19-net-dsa-qca8k-enlarge-mdio-delay-and-timeout.patch +++ /dev/null @@ -1,39 +0,0 @@ -From 617960d72e93de0f3fa52407e2d39e8c43e73b0a Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:09 +0200 -Subject: [PATCH] net: dsa: qca8k: enlarge mdio delay and timeout - -The witch require some extra delay after setting page or the next -read/write can use still use the old page. Add a delay after the -set_page function to address this as it's done in QSDK legacy driver. -Some timeouts were notice with VLAN and phy function, enlarge the -mdio busy wait timeout to fix these problems. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 1 + - drivers/net/dsa/qca8k.h | 2 +- - 2 files changed, 2 insertions(+), 1 deletion(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -143,6 +143,7 @@ qca8k_set_page(struct mii_bus *bus, u16 - } - - qca8k_current_page = page; -+ usleep_range(1000, 2000); - return 0; - } - ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -20,7 +20,7 @@ - #define PHY_ID_QCA8337 0x004dd036 - #define QCA8K_ID_QCA8337 0x13 - --#define QCA8K_BUSY_WAIT_TIMEOUT 20 -+#define QCA8K_BUSY_WAIT_TIMEOUT 2000 - - #define QCA8K_NUM_FDB_RECORDS 2048 - diff --git a/target/linux/generic/backport-5.10/785-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch b/target/linux/generic/backport-5.10/785-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch deleted file mode 100644 index 88d3c1ef43..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-20-net-dsa-qca8k-add-support-for-internal-phy-and-inter.patch +++ /dev/null @@ -1,267 +0,0 @@ -From 759bafb8a3226326ca357613bc90acf738f80c32 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:10 +0200 -Subject: [PATCH] net: dsa: qca8k: add support for internal phy and internal - mdio - -Add support to setup_mdio_bus for internal phy declaration. Introduce a -flag to use the legacy port phy mapping by default and use the direct -mapping if a mdio node is detected in the switch node. Register a -dedicated mdio internal mdio bus to address the different mapping -between port and phy if the mdio node is detected. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 112 +++++++++++++++++++++++++++++----------- - drivers/net/dsa/qca8k.h | 1 + - 2 files changed, 83 insertions(+), 30 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -11,6 +11,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -629,7 +630,7 @@ qca8k_port_to_phy(int port) - } - - static int --qca8k_mdio_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) -+qca8k_mdio_busy_wait(struct mii_bus *bus, u32 reg, u32 mask) - { - u16 r1, r2, page; - u32 val; -@@ -639,7 +640,7 @@ qca8k_mdio_busy_wait(struct qca8k_priv * - - ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, - QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, -- priv->bus, 0x10 | r2, r1); -+ bus, 0x10 | r2, r1); - - /* Check if qca8k_read has failed for a different reason - * before returnting -ETIMEDOUT -@@ -651,19 +652,16 @@ qca8k_mdio_busy_wait(struct qca8k_priv * - } - - static int --qca8k_mdio_write(struct qca8k_priv *priv, int port, u32 regnum, u16 data) -+qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) - { -+ struct qca8k_priv *priv = salve_bus->priv; - u16 r1, r2, page; -- u32 phy, val; -+ u32 val; - int ret; - - if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) - return -EINVAL; - -- /* callee is responsible for not passing bad ports, -- * but we still would like to make spills impossible. -- */ -- phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; - val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | - QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | - QCA8K_MDIO_MASTER_REG_ADDR(regnum) | -@@ -679,33 +677,29 @@ qca8k_mdio_write(struct qca8k_priv *priv - - qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); - -- ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY); - - exit: -- mutex_unlock(&priv->bus->mdio_lock); -- - /* even if the busy_wait timeouts try to clear the MASTER_EN */ -- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_EN); -+ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); -+ -+ mutex_unlock(&priv->bus->mdio_lock); - - return ret; - } - - static int --qca8k_mdio_read(struct qca8k_priv *priv, int port, u32 regnum) -+qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) - { -+ struct qca8k_priv *priv = salve_bus->priv; - u16 r1, r2, page; -- u32 phy, val; -+ u32 val; - int ret; - - if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) - return -EINVAL; - -- /* callee is responsible for not passing bad ports, -- * but we still would like to make spills impossible. -- */ -- phy = qca8k_port_to_phy(port) % PHY_MAX_ADDR; - val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | - QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | - QCA8K_MDIO_MASTER_REG_ADDR(regnum); -@@ -720,24 +714,22 @@ qca8k_mdio_read(struct qca8k_priv *priv, - - qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); - -- ret = qca8k_mdio_busy_wait(priv, QCA8K_MDIO_MASTER_CTRL, -+ ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY); - if (ret) - goto exit; - - val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); -- val &= QCA8K_MDIO_MASTER_DATA_MASK; - - exit: -+ /* even if the busy_wait timeouts try to clear the MASTER_EN */ -+ qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); -+ - mutex_unlock(&priv->bus->mdio_lock); - - if (val >= 0) - val &= QCA8K_MDIO_MASTER_DATA_MASK; - -- /* even if the busy_wait timeouts try to clear the MASTER_EN */ -- qca8k_reg_clear(priv, QCA8K_MDIO_MASTER_CTRL, -- QCA8K_MDIO_MASTER_EN); -- - return val; - } - -@@ -746,7 +738,14 @@ qca8k_phy_write(struct dsa_switch *ds, i - { - struct qca8k_priv *priv = ds->priv; - -- return qca8k_mdio_write(priv, port, regnum, data); -+ /* Check if the legacy mapping should be used and the -+ * port is not correctly mapped to the right PHY in the -+ * devicetree -+ */ -+ if (priv->legacy_phy_port_mapping) -+ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; -+ -+ return qca8k_mdio_write(priv->bus, port, regnum, data); - } - - static int -@@ -755,7 +754,14 @@ qca8k_phy_read(struct dsa_switch *ds, in - struct qca8k_priv *priv = ds->priv; - int ret; - -- ret = qca8k_mdio_read(priv, port, regnum); -+ /* Check if the legacy mapping should be used and the -+ * port is not correctly mapped to the right PHY in the -+ * devicetree -+ */ -+ if (priv->legacy_phy_port_mapping) -+ port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; -+ -+ ret = qca8k_mdio_read(priv->bus, port, regnum); - - if (ret < 0) - return 0xffff; -@@ -764,10 +770,37 @@ qca8k_phy_read(struct dsa_switch *ds, in - } - - static int -+qca8k_mdio_register(struct qca8k_priv *priv, struct device_node *mdio) -+{ -+ struct dsa_switch *ds = priv->ds; -+ struct mii_bus *bus; -+ -+ bus = devm_mdiobus_alloc(ds->dev); -+ -+ if (!bus) -+ return -ENOMEM; -+ -+ bus->priv = (void *)priv; -+ bus->name = "qca8k slave mii"; -+ bus->read = qca8k_mdio_read; -+ bus->write = qca8k_mdio_write; -+ snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d", -+ ds->index); -+ -+ bus->parent = ds->dev; -+ bus->phy_mask = ~ds->phys_mii_mask; -+ -+ ds->slave_mii_bus = bus; -+ -+ return devm_of_mdiobus_register(priv->dev, bus, mdio); -+} -+ -+static int - qca8k_setup_mdio_bus(struct qca8k_priv *priv) - { - u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg; -- struct device_node *ports, *port; -+ struct device_node *ports, *port, *mdio; -+ phy_interface_t mode; - int err; - - ports = of_get_child_by_name(priv->dev->of_node, "ports"); -@@ -788,7 +821,10 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - if (!dsa_is_user_port(priv->ds, reg)) - continue; - -- if (of_property_read_bool(port, "phy-handle")) -+ of_get_phy_mode(port, &mode); -+ -+ if (of_property_read_bool(port, "phy-handle") && -+ mode != PHY_INTERFACE_MODE_INTERNAL) - external_mdio_mask |= BIT(reg); - else - internal_mdio_mask |= BIT(reg); -@@ -825,8 +861,23 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - QCA8K_MDIO_MASTER_EN); - } - -+ /* Check if the devicetree declare the port:phy mapping */ -+ mdio = of_get_child_by_name(priv->dev->of_node, "mdio"); -+ if (of_device_is_available(mdio)) { -+ err = qca8k_mdio_register(priv, mdio); -+ if (err) -+ of_node_put(mdio); -+ -+ return err; -+ } -+ -+ /* If a mapping can't be found the legacy mapping is used, -+ * using the qca8k_port_to_phy function -+ */ -+ priv->legacy_phy_port_mapping = true; - priv->ops.phy_read = qca8k_phy_read; - priv->ops.phy_write = qca8k_phy_write; -+ - return 0; - } - -@@ -1212,7 +1263,8 @@ qca8k_phylink_validate(struct dsa_switch - case 5: - /* Internal PHY */ - if (state->interface != PHY_INTERFACE_MODE_NA && -- state->interface != PHY_INTERFACE_MODE_GMII) -+ state->interface != PHY_INTERFACE_MODE_GMII && -+ state->interface != PHY_INTERFACE_MODE_INTERNAL) - goto unsupported; - break; - case 6: /* 2nd CPU port / external PHY */ ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -255,6 +255,7 @@ struct qca8k_priv { - u8 switch_revision; - u8 rgmii_tx_delay; - u8 rgmii_rx_delay; -+ bool legacy_phy_port_mapping; - struct regmap *regmap; - struct mii_bus *bus; - struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/785-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch b/target/linux/generic/backport-5.10/785-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch deleted file mode 100644 index 6db01b4b41..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-21-devicetree-bindings-dsa-qca8k-Document-internal-mdio.patch +++ /dev/null @@ -1,93 +0,0 @@ -From 0c994a28e7518f098c84a3049cb2915780db873a Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:11 +0200 -Subject: [PATCH] devicetree: bindings: dsa: qca8k: Document internal mdio - definition - -Document new way of declare mapping of internal PHY to port. -The new implementation directly declare the PHY connected to the port -by adding a node in the switch node. The driver detect this and register -an internal mdiobus using the mapping defined in the mdio node. - -Signed-off-by: Ansuel Smith -Reviewed-by: Rob Herring -Signed-off-by: David S. Miller ---- - .../devicetree/bindings/net/dsa/qca8k.txt | 39 +++++++++++++++++++ - 1 file changed, 39 insertions(+) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -21,6 +21,10 @@ described in dsa/dsa.txt. If the QCA8K s - mdio-bus each subnode describing a port needs to have a valid phandle - referencing the internal PHY it is connected to. This is because there's no - N:N mapping of port and PHY id. -+To declare the internal mdio-bus configuration, declare a mdio node in the -+switch node and declare the phandle for the port referencing the internal -+PHY is connected to. In this config a internal mdio-bus is registered and -+the mdio MASTER is used as communication. - - Don't use mixed external and internal mdio-bus configurations, as this is - not supported by the hardware. -@@ -150,26 +154,61 @@ for the internal master mdio-bus configu - port@1 { - reg = <1>; - label = "lan1"; -+ phy-mode = "internal"; -+ phy-handle = <&phy_port1>; - }; - - port@2 { - reg = <2>; - label = "lan2"; -+ phy-mode = "internal"; -+ phy-handle = <&phy_port2>; - }; - - port@3 { - reg = <3>; - label = "lan3"; -+ phy-mode = "internal"; -+ phy-handle = <&phy_port3>; - }; - - port@4 { - reg = <4>; - label = "lan4"; -+ phy-mode = "internal"; -+ phy-handle = <&phy_port4>; - }; - - port@5 { - reg = <5>; - label = "wan"; -+ phy-mode = "internal"; -+ phy-handle = <&phy_port5>; -+ }; -+ }; -+ -+ mdio { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ phy_port1: phy@0 { -+ reg = <0>; -+ }; -+ -+ phy_port2: phy@1 { -+ reg = <1>; -+ }; -+ -+ phy_port3: phy@2 { -+ reg = <2>; -+ }; -+ -+ phy_port4: phy@3 { -+ reg = <3>; -+ }; -+ -+ phy_port5: phy@4 { -+ reg = <4>; - }; - }; - }; diff --git a/target/linux/generic/backport-5.10/785-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch b/target/linux/generic/backport-5.10/785-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch deleted file mode 100644 index da8d5b3462..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-22-net-dsa-qca8k-improve-internal-mdio-read-write-bus-a.patch +++ /dev/null @@ -1,95 +0,0 @@ -From b7ebac354d54f1657bb89b7a7ca149db50203e6a Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:12 +0200 -Subject: [PATCH] net: dsa: qca8k: improve internal mdio read/write bus access - -Improve the internal mdio read/write bus access by caching the value -without accessing it for every read/write. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 28 +++++++++++++++------------- - 1 file changed, 15 insertions(+), 13 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -655,6 +655,7 @@ static int - qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) - { - struct qca8k_priv *priv = salve_bus->priv; -+ struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 val; - int ret; -@@ -669,22 +670,22 @@ qca8k_mdio_write(struct mii_bus *salve_b - - qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); - -- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- ret = qca8k_set_page(priv->bus, page); -+ ret = qca8k_set_page(bus, page); - if (ret) - goto exit; - -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, val); - -- ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, -+ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY); - - exit: - /* even if the busy_wait timeouts try to clear the MASTER_EN */ -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, 0); - -- mutex_unlock(&priv->bus->mdio_lock); -+ mutex_unlock(&bus->mdio_lock); - - return ret; - } -@@ -693,6 +694,7 @@ static int - qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) - { - struct qca8k_priv *priv = salve_bus->priv; -+ struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 val; - int ret; -@@ -706,26 +708,26 @@ qca8k_mdio_read(struct mii_bus *salve_bu - - qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); - -- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); -+ mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- ret = qca8k_set_page(priv->bus, page); -+ ret = qca8k_set_page(bus, page); - if (ret) - goto exit; - -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, val); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, val); - -- ret = qca8k_mdio_busy_wait(priv->bus, QCA8K_MDIO_MASTER_CTRL, -+ ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, - QCA8K_MDIO_MASTER_BUSY); - if (ret) - goto exit; - -- val = qca8k_mii_read32(priv->bus, 0x10 | r2, r1); -+ val = qca8k_mii_read32(bus, 0x10 | r2, r1); - - exit: - /* even if the busy_wait timeouts try to clear the MASTER_EN */ -- qca8k_mii_write32(priv->bus, 0x10 | r2, r1, 0); -+ qca8k_mii_write32(bus, 0x10 | r2, r1, 0); - -- mutex_unlock(&priv->bus->mdio_lock); -+ mutex_unlock(&bus->mdio_lock); - - if (val >= 0) - val &= QCA8K_MDIO_MASTER_DATA_MASK; diff --git a/target/linux/generic/backport-5.10/785-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch b/target/linux/generic/backport-5.10/785-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch deleted file mode 100644 index 1179cf152d..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-23-net-dsa-qca8k-pass-switch_revision-info-to-phy-dev_f.patch +++ /dev/null @@ -1,48 +0,0 @@ -From a46aec02bc06ac2c33f326339e4ef88c735dc30d Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:13 +0200 -Subject: [PATCH] net: dsa: qca8k: pass switch_revision info to phy dev_flags - -Define get_phy_flags to pass switch_Revision needed to tweak the -internal PHY with debug values based on the revision. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 17 +++++++++++++++++ - 1 file changed, 17 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1740,6 +1740,22 @@ qca8k_port_vlan_del(struct dsa_switch *d - return ret; - } - -+static u32 qca8k_get_phy_flags(struct dsa_switch *ds, int port) -+{ -+ struct qca8k_priv *priv = ds->priv; -+ -+ /* Communicate to the phy internal driver the switch revision. -+ * Based on the switch revision different values needs to be -+ * set to the dbg and mmd reg on the phy. -+ * The first 2 bit are used to communicate the switch revision -+ * to the phy driver. -+ */ -+ if (port > 0 && port < 6) -+ return priv->switch_revision; -+ -+ return 0; -+} -+ - static enum dsa_tag_protocol - qca8k_get_tag_protocol(struct dsa_switch *ds, int port, - enum dsa_tag_protocol mp) -@@ -1774,6 +1790,7 @@ static const struct dsa_switch_ops qca8k - .phylink_mac_config = qca8k_phylink_mac_config, - .phylink_mac_link_down = qca8k_phylink_mac_link_down, - .phylink_mac_link_up = qca8k_phylink_mac_link_up, -+ .get_phy_flags = qca8k_get_phy_flags, - }; - - static int qca8k_read_switch_id(struct qca8k_priv *priv) diff --git a/target/linux/generic/backport-5.10/785-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch b/target/linux/generic/backport-5.10/785-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch deleted file mode 100644 index 20325f564d..0000000000 --- a/target/linux/generic/backport-5.10/785-v5.14-25-net-phy-add-support-for-qca8k-switch-internal-PHY-in.patch +++ /dev/null @@ -1,229 +0,0 @@ -From 272833b9b3b3969be7a91839121d86662c8c4253 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Fri, 14 May 2021 23:00:15 +0200 -Subject: [PATCH] net: phy: add support for qca8k switch internal PHY in at803x - -Since the at803x share the same regs, it's assumed they are based on the -same implementation. Make it part of the at803x PHY driver to skip -having redudant code. -Add initial support for qca8k internal PHYs. The internal PHYs requires -special mmd and debug values to be set based on the switch revision -passwd using the dev_flags. Supports output of idle, receive and eee_wake -errors stats. -Some debug values sets can't be translated as the documentation lacks any -reference about them. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/phy/Kconfig | 5 +- - drivers/net/phy/at803x.c | 132 ++++++++++++++++++++++++++++++++++++++- - 2 files changed, 134 insertions(+), 3 deletions(-) - ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -235,10 +235,11 @@ config NXP_TJA11XX_PHY - Currently supports the NXP TJA1100 and TJA1101 PHY. - - config AT803X_PHY -- tristate "Qualcomm Atheros AR803X PHYs" -+ tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs" - depends on REGULATOR - help -- Currently supports the AR8030, AR8031, AR8033 and AR8035 model -+ Currently supports the AR8030, AR8031, AR8033, AR8035 and internal -+ QCA8337(Internal qca8k PHY) model - - config QSEMI_PHY - tristate "Quality Semiconductor PHYs" ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -92,10 +92,16 @@ - #define AT803X_DEBUG_REG_5 0x05 - #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) - -+#define AT803X_DEBUG_REG_3C 0x3C -+ -+#define AT803X_DEBUG_REG_3D 0x3D -+ - #define AT803X_DEBUG_REG_1F 0x1F - #define AT803X_DEBUG_PLL_ON BIT(2) - #define AT803X_DEBUG_RGMII_1V8 BIT(3) - -+#define MDIO_AZ_DEBUG 0x800D -+ - /* AT803x supports either the XTAL input pad, an internal PLL or the - * DSP as clock reference for the clock output pad. The XTAL reference - * is only used for 25 MHz output, all other frequencies need the PLL. -@@ -142,10 +148,34 @@ - #define AT803X_PAGE_FIBER 0 - #define AT803X_PAGE_COPPER 1 - -+#define QCA8327_PHY_ID 0x004dd034 -+#define QCA8337_PHY_ID 0x004dd036 -+#define QCA8K_PHY_ID_MASK 0xffffffff -+ -+#define QCA8K_DEVFLAGS_REVISION_MASK GENMASK(2, 0) -+ - MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver"); - MODULE_AUTHOR("Matus Ujhelyi"); - MODULE_LICENSE("GPL"); - -+enum stat_access_type { -+ PHY, -+ MMD -+}; -+ -+struct at803x_hw_stat { -+ const char *string; -+ u8 reg; -+ u32 mask; -+ enum stat_access_type access_type; -+}; -+ -+static struct at803x_hw_stat at803x_hw_stats[] = { -+ { "phy_idle_errors", 0xa, GENMASK(7, 0), PHY}, -+ { "phy_receive_errors", 0x15, GENMASK(15, 0), PHY}, -+ { "eee_wake_errors", 0x16, GENMASK(15, 0), MMD}, -+}; -+ - struct at803x_priv { - int flags; - #define AT803X_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */ -@@ -154,6 +184,7 @@ struct at803x_priv { - struct regulator_dev *vddio_rdev; - struct regulator_dev *vddh_rdev; - struct regulator *vddio; -+ u64 stats[ARRAY_SIZE(at803x_hw_stats)]; - }; - - struct at803x_context { -@@ -165,6 +196,17 @@ struct at803x_context { - u16 led_control; - }; - -+static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data) -+{ -+ int ret; -+ -+ ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg); -+ if (ret < 0) -+ return ret; -+ -+ return phy_write(phydev, AT803X_DEBUG_DATA, data); -+} -+ - static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg) - { - int ret; -@@ -327,6 +369,53 @@ static void at803x_get_wol(struct phy_de - wol->wolopts |= WAKE_MAGIC; - } - -+static int at803x_get_sset_count(struct phy_device *phydev) -+{ -+ return ARRAY_SIZE(at803x_hw_stats); -+} -+ -+static void at803x_get_strings(struct phy_device *phydev, u8 *data) -+{ -+ int i; -+ -+ for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) { -+ strscpy(data + i * ETH_GSTRING_LEN, -+ at803x_hw_stats[i].string, ETH_GSTRING_LEN); -+ } -+} -+ -+static u64 at803x_get_stat(struct phy_device *phydev, int i) -+{ -+ struct at803x_hw_stat stat = at803x_hw_stats[i]; -+ struct at803x_priv *priv = phydev->priv; -+ int val; -+ u64 ret; -+ -+ if (stat.access_type == MMD) -+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg); -+ else -+ val = phy_read(phydev, stat.reg); -+ -+ if (val < 0) { -+ ret = U64_MAX; -+ } else { -+ val = val & stat.mask; -+ priv->stats[i] += val; -+ ret = priv->stats[i]; -+ } -+ -+ return ret; -+} -+ -+static void at803x_get_stats(struct phy_device *phydev, -+ struct ethtool_stats *stats, u64 *data) -+{ -+ int i; -+ -+ for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) -+ data[i] = at803x_get_stat(phydev, i); -+} -+ - static int at803x_suspend(struct phy_device *phydev) - { - int value; -@@ -1102,6 +1191,34 @@ static int at803x_cable_test_start(struc - return 0; - } - -+static int qca83xx_config_init(struct phy_device *phydev) -+{ -+ u8 switch_revision; -+ -+ switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK; -+ -+ switch (switch_revision) { -+ case 1: -+ /* For 100M waveform */ -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_0, 0x02ea); -+ /* Turn on Gigabit clock */ -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x68a0); -+ break; -+ -+ case 2: -+ phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0); -+ fallthrough; -+ case 4: -+ phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x6860); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_5, 0x2c46); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000); -+ break; -+ } -+ -+ return 0; -+} -+ - static struct phy_driver at803x_driver[] = { - { - /* Qualcomm Atheros AR8035 */ -@@ -1198,7 +1315,20 @@ static struct phy_driver at803x_driver[] - .read_status = at803x_read_status, - .soft_reset = genphy_soft_reset, - .config_aneg = at803x_config_aneg, --} }; -+}, { -+ /* QCA8337 */ -+ .phy_id = QCA8337_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "QCA PHY 8337", -+ /* PHY_GBIT_FEATURES */ -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, -+}, }; - - module_phy_driver(at803x_driver); - diff --git a/target/linux/generic/backport-5.10/786-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch b/target/linux/generic/backport-5.10/786-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch deleted file mode 100644 index a68e3b1821..0000000000 --- a/target/linux/generic/backport-5.10/786-v5.14-net-dsa-qca8k-fix-missing-unlock-on-error-in-qca8k-vlan.patch +++ /dev/null @@ -1,64 +0,0 @@ -From 0d56e5c191b197e1d30a0a4c92628836dafced0f Mon Sep 17 00:00:00 2001 -From: Wei Yongjun -Date: Tue, 18 May 2021 11:24:13 +0000 -Subject: [PATCH] net: dsa: qca8k: fix missing unlock on error in - qca8k_vlan_(add|del) - -Add the missing unlock before return from function qca8k_vlan_add() -and qca8k_vlan_del() in the error handling case. - -Fixes: 028f5f8ef44f ("net: dsa: qca8k: handle error with qca8k_read operation") -Reported-by: Hulk Robot -Signed-off-by: Wei Yongjun -Reviewed-by: Vladimir Oltean -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 16 ++++++++++------ - 1 file changed, 10 insertions(+), 6 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -506,8 +506,10 @@ qca8k_vlan_add(struct qca8k_priv *priv, - goto out; - - reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -- if (reg < 0) -- return reg; -+ if (reg < 0) { -+ ret = reg; -+ goto out; -+ } - reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; - reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - if (untagged) -@@ -519,7 +521,7 @@ qca8k_vlan_add(struct qca8k_priv *priv, - - ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); - if (ret) -- return ret; -+ goto out; - ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); - - out: -@@ -541,8 +543,10 @@ qca8k_vlan_del(struct qca8k_priv *priv, - goto out; - - reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -- if (reg < 0) -- return reg; -+ if (reg < 0) { -+ ret = reg; -+ goto out; -+ } - reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << - QCA8K_VTU_FUNC0_EG_MODE_S(port); -@@ -564,7 +568,7 @@ qca8k_vlan_del(struct qca8k_priv *priv, - } else { - ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); - if (ret) -- return ret; -+ goto out; - ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); - } - diff --git a/target/linux/generic/backport-5.10/787-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch b/target/linux/generic/backport-5.10/787-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch deleted file mode 100644 index 451b0e9446..0000000000 --- a/target/linux/generic/backport-5.10/787-v5.14-01-net-dsa-qca8k-check-return-value-of-read-functions-c.patch +++ /dev/null @@ -1,348 +0,0 @@ -From 7c9896e37807862e276064dd9331860f5d27affc Mon Sep 17 00:00:00 2001 -From: Yang Yingliang -Date: Sat, 29 May 2021 11:04:38 +0800 -Subject: [PATCH] net: dsa: qca8k: check return value of read functions - correctly - -Current return type of qca8k_mii_read32() and qca8k_read() are -unsigned, it can't be negative, so the return value check is -unuseful. For check the return value correctly, change return -type of the read functions and add a output parameter to store -the read value. - -Signed-off-by: Yang Yingliang -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/qca8k.c | 130 +++++++++++++++++++--------------------- - 1 file changed, 60 insertions(+), 70 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -89,26 +89,26 @@ qca8k_split_addr(u32 regaddr, u16 *r1, u - *page = regaddr & 0x3ff; - } - --static u32 --qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum) -+static int -+qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum, u32 *val) - { -- u32 val; - int ret; - - ret = bus->read(bus, phy_id, regnum); - if (ret >= 0) { -- val = ret; -+ *val = ret; - ret = bus->read(bus, phy_id, regnum + 1); -- val |= ret << 16; -+ *val |= ret << 16; - } - - if (ret < 0) { - dev_err_ratelimited(&bus->dev, - "failed to read qca8k 32bit register\n"); -+ *val = 0; - return ret; - } - -- return val; -+ return 0; - } - - static void -@@ -148,26 +148,26 @@ qca8k_set_page(struct mii_bus *bus, u16 - return 0; - } - --static u32 --qca8k_read(struct qca8k_priv *priv, u32 reg) -+static int -+qca8k_read(struct qca8k_priv *priv, u32 reg, u32 *val) - { - struct mii_bus *bus = priv->bus; - u16 r1, r2, page; -- u32 val; -+ int ret; - - qca8k_split_addr(reg, &r1, &r2, &page); - - mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); - -- val = qca8k_set_page(bus, page); -- if (val < 0) -+ ret = qca8k_set_page(bus, page); -+ if (ret < 0) - goto exit; - -- val = qca8k_mii_read32(bus, 0x10 | r2, r1); -+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, val); - - exit: - mutex_unlock(&bus->mdio_lock); -- return val; -+ return ret; - } - - static int -@@ -208,11 +208,9 @@ qca8k_rmw(struct qca8k_priv *priv, u32 r - if (ret < 0) - goto exit; - -- val = qca8k_mii_read32(bus, 0x10 | r2, r1); -- if (val < 0) { -- ret = val; -+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); -+ if (ret < 0) - goto exit; -- } - - val &= ~mask; - val |= write_val; -@@ -240,15 +238,8 @@ static int - qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ctx; -- int ret; -- -- ret = qca8k_read(priv, reg); -- if (ret < 0) -- return ret; -- -- *val = ret; - -- return 0; -+ return qca8k_read(priv, reg, val); - } - - static int -@@ -296,18 +287,18 @@ static struct regmap_config qca8k_regmap - static int - qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) - { -+ int ret, ret1; - u32 val; -- int ret; - -- ret = read_poll_timeout(qca8k_read, val, !(val & mask), -+ ret = read_poll_timeout(qca8k_read, ret1, !(val & mask), - 0, QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, -- priv, reg); -+ priv, reg, &val); - - /* Check if qca8k_read has failed for a different reason - * before returning -ETIMEDOUT - */ -- if (ret < 0 && val < 0) -- return val; -+ if (ret < 0 && ret1 < 0) -+ return ret1; - - return ret; - } -@@ -316,13 +307,13 @@ static int - qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) - { - u32 reg[4], val; -- int i; -+ int i, ret; - - /* load the ARL table into an array */ - for (i = 0; i < 4; i++) { -- val = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4)); -- if (val < 0) -- return val; -+ ret = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4), &val); -+ if (ret < 0) -+ return ret; - - reg[i] = val; - } -@@ -396,9 +387,9 @@ qca8k_fdb_access(struct qca8k_priv *priv - - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_FDB_LOAD) { -- reg = qca8k_read(priv, QCA8K_REG_ATU_FUNC); -- if (reg < 0) -- return reg; -+ ret = qca8k_read(priv, QCA8K_REG_ATU_FUNC, ®); -+ if (ret < 0) -+ return ret; - if (reg & QCA8K_ATU_FUNC_FULL) - return -1; - } -@@ -477,9 +468,9 @@ qca8k_vlan_access(struct qca8k_priv *pri - - /* Check for table full violation when adding an entry */ - if (cmd == QCA8K_VLAN_LOAD) { -- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1); -- if (reg < 0) -- return reg; -+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC1, ®); -+ if (ret < 0) -+ return ret; - if (reg & QCA8K_VTU_FUNC1_FULL) - return -ENOMEM; - } -@@ -505,11 +496,9 @@ qca8k_vlan_add(struct qca8k_priv *priv, - if (ret < 0) - goto out; - -- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -- if (reg < 0) { -- ret = reg; -+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); -+ if (ret < 0) - goto out; -- } - reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; - reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - if (untagged) -@@ -542,11 +531,9 @@ qca8k_vlan_del(struct qca8k_priv *priv, - if (ret < 0) - goto out; - -- reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0); -- if (reg < 0) { -- ret = reg; -+ ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); -+ if (ret < 0) - goto out; -- } - reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port)); - reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT << - QCA8K_VTU_FUNC0_EG_MODE_S(port); -@@ -638,19 +625,19 @@ qca8k_mdio_busy_wait(struct mii_bus *bus - { - u16 r1, r2, page; - u32 val; -- int ret; -+ int ret, ret1; - - qca8k_split_addr(reg, &r1, &r2, &page); - -- ret = read_poll_timeout(qca8k_mii_read32, val, !(val & mask), 0, -+ ret = read_poll_timeout(qca8k_mii_read32, ret1, !(val & mask), 0, - QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, -- bus, 0x10 | r2, r1); -+ bus, 0x10 | r2, r1, &val); - - /* Check if qca8k_read has failed for a different reason - * before returnting -ETIMEDOUT - */ -- if (ret < 0 && val < 0) -- return val; -+ if (ret < 0 && ret1 < 0) -+ return ret1; - - return ret; - } -@@ -725,7 +712,7 @@ qca8k_mdio_read(struct mii_bus *salve_bu - if (ret) - goto exit; - -- val = qca8k_mii_read32(bus, 0x10 | r2, r1); -+ ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); - - exit: - /* even if the busy_wait timeouts try to clear the MASTER_EN */ -@@ -733,10 +720,10 @@ exit: - - mutex_unlock(&bus->mdio_lock); - -- if (val >= 0) -- val &= QCA8K_MDIO_MASTER_DATA_MASK; -+ if (ret >= 0) -+ ret = val & QCA8K_MDIO_MASTER_DATA_MASK; - -- return val; -+ return ret; - } - - static int -@@ -1211,7 +1198,7 @@ qca8k_phylink_mac_config(struct dsa_swit - qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); - - /* Enable/disable SerDes auto-negotiation as necessary */ -- val = qca8k_read(priv, QCA8K_REG_PWS); -+ qca8k_read(priv, QCA8K_REG_PWS, &val); - if (phylink_autoneg_inband(mode)) - val &= ~QCA8K_PWS_SERDES_AEN_DIS; - else -@@ -1219,7 +1206,7 @@ qca8k_phylink_mac_config(struct dsa_swit - qca8k_write(priv, QCA8K_REG_PWS, val); - - /* Configure the SGMII parameters */ -- val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL); -+ qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); - - val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | - QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; -@@ -1314,10 +1301,11 @@ qca8k_phylink_mac_link_state(struct dsa_ - { - struct qca8k_priv *priv = ds->priv; - u32 reg; -+ int ret; - -- reg = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port)); -- if (reg < 0) -- return reg; -+ ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), ®); -+ if (ret < 0) -+ return ret; - - state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); - state->an_complete = state->link; -@@ -1419,19 +1407,20 @@ qca8k_get_ethtool_stats(struct dsa_switc - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - const struct qca8k_mib_desc *mib; - u32 reg, i, val; -- u64 hi; -+ u64 hi = 0; -+ int ret; - - for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { - mib = &ar8327_mib[i]; - reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; - -- val = qca8k_read(priv, reg); -- if (val < 0) -+ ret = qca8k_read(priv, reg, &val); -+ if (ret < 0) - continue; - - if (mib->size == 2) { -- hi = qca8k_read(priv, reg + 4); -- if (hi < 0) -+ ret = qca8k_read(priv, reg + 4, (u32 *)&hi); -+ if (ret < 0) - continue; - } - -@@ -1459,7 +1448,7 @@ qca8k_set_mac_eee(struct dsa_switch *ds, - int ret; - - mutex_lock(&priv->reg_mutex); -- reg = qca8k_read(priv, QCA8K_REG_EEE_CTRL); -+ ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®); - if (reg < 0) { - ret = reg; - goto exit; -@@ -1802,14 +1791,15 @@ static int qca8k_read_switch_id(struct q - const struct qca8k_match_data *data; - u32 val; - u8 id; -+ int ret; - - /* get the switches ID from the compatible */ - data = of_device_get_match_data(priv->dev); - if (!data) - return -ENODEV; - -- val = qca8k_read(priv, QCA8K_REG_MASK_CTRL); -- if (val < 0) -+ ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val); -+ if (ret < 0) - return -ENODEV; - - id = QCA8K_MASK_CTRL_DEVICE_ID(val & QCA8K_MASK_CTRL_DEVICE_ID_MASK); diff --git a/target/linux/generic/backport-5.10/787-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch b/target/linux/generic/backport-5.10/787-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch deleted file mode 100644 index d20da5b85e..0000000000 --- a/target/linux/generic/backport-5.10/787-v5.14-02-net-dsa-qca8k-add-missing-check-return-value-in-qca8.patch +++ /dev/null @@ -1,47 +0,0 @@ -From 9fe99de01440d9ede74d447ac76e9c445d8daae9 Mon Sep 17 00:00:00 2001 -From: Yang Yingliang -Date: Sat, 29 May 2021 11:04:39 +0800 -Subject: [PATCH] net: dsa: qca8k: add missing check return value in - qca8k_phylink_mac_config() - -Now we can check qca8k_read() return value correctly, so if -it fails, we need return directly. - -Signed-off-by: Yang Yingliang -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/qca8k.c | 9 +++++++-- - 1 file changed, 7 insertions(+), 2 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1128,6 +1128,7 @@ qca8k_phylink_mac_config(struct dsa_swit - { - struct qca8k_priv *priv = ds->priv; - u32 reg, val; -+ int ret; - - switch (port) { - case 0: /* 1st CPU port */ -@@ -1198,7 +1199,9 @@ qca8k_phylink_mac_config(struct dsa_swit - qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); - - /* Enable/disable SerDes auto-negotiation as necessary */ -- qca8k_read(priv, QCA8K_REG_PWS, &val); -+ ret = qca8k_read(priv, QCA8K_REG_PWS, &val); -+ if (ret) -+ return; - if (phylink_autoneg_inband(mode)) - val &= ~QCA8K_PWS_SERDES_AEN_DIS; - else -@@ -1206,7 +1209,9 @@ qca8k_phylink_mac_config(struct dsa_swit - qca8k_write(priv, QCA8K_REG_PWS, val); - - /* Configure the SGMII parameters */ -- qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); -+ ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); -+ if (ret) -+ return; - - val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | - QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; diff --git a/target/linux/generic/backport-5.10/788-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch b/target/linux/generic/backport-5.10/788-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch deleted file mode 100644 index 429d5d50f0..0000000000 --- a/target/linux/generic/backport-5.10/788-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch +++ /dev/null @@ -1,47 +0,0 @@ -aFrom aa3d020b22cb844ab7bdbb9e5d861a64666e2b74 Mon Sep 17 00:00:00 2001 -From: Dan Carpenter -Date: Wed, 9 Jun 2021 12:52:12 +0300 -Subject: [PATCH] net: dsa: qca8k: fix an endian bug in - qca8k_get_ethtool_stats() - -The "hi" variable is a u64 but the qca8k_read() writes to the top 32 -bits of it. That will work on little endian systems but it's a bit -subtle. It's cleaner to make declare "hi" as a u32. We will still need -to cast it when we shift it later on in the function but that's fine. - -Fixes: 7c9896e37807 ("net: dsa: qca8k: check return value of read functions correctly") -Signed-off-by: Dan Carpenter -Reviewed-by: Vladimir Oltean -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 6 +++--- - 1 file changed, 3 insertions(+), 3 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1412,7 +1412,7 @@ qca8k_get_ethtool_stats(struct dsa_switc - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; - const struct qca8k_mib_desc *mib; - u32 reg, i, val; -- u64 hi = 0; -+ u32 hi = 0; - int ret; - - for (i = 0; i < ARRAY_SIZE(ar8327_mib); i++) { -@@ -1424,14 +1424,14 @@ qca8k_get_ethtool_stats(struct dsa_switc - continue; - - if (mib->size == 2) { -- ret = qca8k_read(priv, reg + 4, (u32 *)&hi); -+ ret = qca8k_read(priv, reg + 4, &hi); - if (ret < 0) - continue; - } - - data[i] = val; - if (mib->size == 2) -- data[i] |= hi << 32; -+ data[i] |= (u64)hi << 32; - } - } - diff --git a/target/linux/generic/backport-5.10/788-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch b/target/linux/generic/backport-5.10/788-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch deleted file mode 100644 index c58f79cd8b..0000000000 --- a/target/linux/generic/backport-5.10/788-v5.14-02-net-dsa-qca8k-check-the-correct-variable-in-qca8k-se.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 3d0167f2a627528032821cdeb78b4eab0510460f Mon Sep 17 00:00:00 2001 -From: Dan Carpenter -Date: Wed, 9 Jun 2021 12:53:03 +0300 -Subject: [PATCH] net: dsa: qca8k: check the correct variable in - qca8k_set_mac_eee() - -This code check "reg" but "ret" was intended so the error handling will -never trigger. - -Fixes: 7c9896e37807 ("net: dsa: qca8k: check return value of read functions correctly") -Signed-off-by: Dan Carpenter -Reviewed-by: Vladimir Oltean -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 4 +--- - 1 file changed, 1 insertion(+), 3 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1454,10 +1454,8 @@ qca8k_set_mac_eee(struct dsa_switch *ds, - - mutex_lock(&priv->reg_mutex); - ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®); -- if (reg < 0) { -- ret = reg; -+ if (ret < 0) - goto exit; -- } - - if (eee->eee_enabled) - reg |= lpi_en; diff --git a/target/linux/generic/backport-5.10/789-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch b/target/linux/generic/backport-5.10/789-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch deleted file mode 100644 index 1e293d3a0b..0000000000 --- a/target/linux/generic/backport-5.10/789-v5.15-net-dsa-qca8k-fix-kernel-panic-with-legacy-mdio-mapping.patch +++ /dev/null @@ -1,80 +0,0 @@ -From ce062a0adbfe933b1932235fdfd874c4c91d1bb0 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sat, 11 Sep 2021 17:50:09 +0200 -Subject: net: dsa: qca8k: fix kernel panic with legacy mdio mapping - -When the mdio legacy mapping is used the mii_bus priv registered by DSA -refer to the dsa switch struct instead of the qca8k_priv struct and -causes a kernel panic. Create dedicated function when the internal -dedicated mdio driver is used to properly handle the 2 different -implementation. - -Fixes: 759bafb8a322 ("net: dsa: qca8k: add support for internal phy and internal mdio") -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 30 ++++++++++++++++++++++-------- - 1 file changed, 22 insertions(+), 8 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -643,10 +643,8 @@ qca8k_mdio_busy_wait(struct mii_bus *bus - } - - static int --qca8k_mdio_write(struct mii_bus *salve_bus, int phy, int regnum, u16 data) -+qca8k_mdio_write(struct mii_bus *bus, int phy, int regnum, u16 data) - { -- struct qca8k_priv *priv = salve_bus->priv; -- struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 val; - int ret; -@@ -682,10 +680,8 @@ exit: - } - - static int --qca8k_mdio_read(struct mii_bus *salve_bus, int phy, int regnum) -+qca8k_mdio_read(struct mii_bus *bus, int phy, int regnum) - { -- struct qca8k_priv *priv = salve_bus->priv; -- struct mii_bus *bus = priv->bus; - u16 r1, r2, page; - u32 val; - int ret; -@@ -727,6 +723,24 @@ exit: - } - - static int -+qca8k_internal_mdio_write(struct mii_bus *slave_bus, int phy, int regnum, u16 data) -+{ -+ struct qca8k_priv *priv = slave_bus->priv; -+ struct mii_bus *bus = priv->bus; -+ -+ return qca8k_mdio_write(bus, phy, regnum, data); -+} -+ -+static int -+qca8k_internal_mdio_read(struct mii_bus *slave_bus, int phy, int regnum) -+{ -+ struct qca8k_priv *priv = slave_bus->priv; -+ struct mii_bus *bus = priv->bus; -+ -+ return qca8k_mdio_read(bus, phy, regnum); -+} -+ -+static int - qca8k_phy_write(struct dsa_switch *ds, int port, int regnum, u16 data) - { - struct qca8k_priv *priv = ds->priv; -@@ -775,8 +789,8 @@ qca8k_mdio_register(struct qca8k_priv *p - - bus->priv = (void *)priv; - bus->name = "qca8k slave mii"; -- bus->read = qca8k_mdio_read; -- bus->write = qca8k_mdio_write; -+ bus->read = qca8k_internal_mdio_read; -+ bus->write = qca8k_internal_mdio_write; - snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d", - ds->index); - diff --git a/target/linux/generic/backport-5.10/790-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch b/target/linux/generic/backport-5.10/790-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch deleted file mode 100644 index 91cf55b18a..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0001-net-dsa-b53-Add-debug-prints-in-b53_vlan_enable.patch +++ /dev/null @@ -1,65 +0,0 @@ -From ee47ed08d75e8f16b3cf882061ee19c2ea19dd6c Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Wed, 10 Mar 2021 10:52:26 -0800 -Subject: [PATCH] net: dsa: b53: Add debug prints in b53_vlan_enable() - -Having dynamic debug prints in b53_vlan_enable() has been helpful to -uncover a recent but update the function to indicate the port being -configured (or -1 for initial setup) and include the global VLAN enabled -and VLAN filtering enable status. - -Signed-off-by: Florian Fainelli -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_common.c | 11 +++++++---- - 1 file changed, 7 insertions(+), 4 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -349,7 +349,7 @@ static void b53_set_forwarding(struct b5 - b53_write8(dev, B53_CTRL_PAGE, B53_IP_MULTICAST_CTRL, mgmt); - } - --static void b53_enable_vlan(struct b53_device *dev, bool enable, -+static void b53_enable_vlan(struct b53_device *dev, int port, bool enable, - bool enable_filtering) - { - u8 mgmt, vc0, vc1, vc4 = 0, vc5; -@@ -431,6 +431,9 @@ static void b53_enable_vlan(struct b53_d - b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt); - - dev->vlan_enabled = enable; -+ -+ dev_dbg(dev->dev, "Port %d VLAN enabled: %d, filtering: %d\n", -+ port, enable, enable_filtering); - } - - static int b53_set_jumbo(struct b53_device *dev, bool enable, bool allow_10_100) -@@ -708,7 +711,7 @@ int b53_configure_vlan(struct dsa_switch - b53_do_vlan_op(dev, VTA_CMD_CLEAR); - } - -- b53_enable_vlan(dev, dev->vlan_enabled, ds->vlan_filtering); -+ b53_enable_vlan(dev, -1, dev->vlan_enabled, ds->vlan_filtering); - - b53_for_each_port(dev, i) - b53_write16(dev, B53_VLAN_PAGE, -@@ -1390,7 +1393,7 @@ int b53_vlan_filtering(struct dsa_switch - if (switchdev_trans_ph_prepare(trans)) - return 0; - -- b53_enable_vlan(dev, dev->vlan_enabled, vlan_filtering); -+ b53_enable_vlan(dev, port, dev->vlan_enabled, vlan_filtering); - - return 0; - } -@@ -1415,7 +1418,7 @@ int b53_vlan_prepare(struct dsa_switch * - if (vlan->vid_end >= dev->num_vlans) - return -ERANGE; - -- b53_enable_vlan(dev, true, ds->vlan_filtering); -+ b53_enable_vlan(dev, port, true, ds->vlan_filtering); - - return 0; - } diff --git a/target/linux/generic/backport-5.10/790-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch b/target/linux/generic/backport-5.10/790-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch deleted file mode 100644 index 56579b2d36..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0002-net-dsa-b53-spi-allow-device-tree-probing.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 6d16eadab6db0c1d61e59fee7ed1ecc2d10269be Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= -Date: Mon, 15 Mar 2021 15:14:23 +0100 -Subject: [PATCH] net: dsa: b53: spi: allow device tree probing -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Add missing of_match_table to allow device tree probing. - -Signed-off-by: Álvaro Fernández Rojas -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_spi.c | 13 +++++++++++++ - 1 file changed, 13 insertions(+) - ---- a/drivers/net/dsa/b53/b53_spi.c -+++ b/drivers/net/dsa/b53/b53_spi.c -@@ -324,9 +324,22 @@ static int b53_spi_remove(struct spi_dev - return 0; - } - -+static const struct of_device_id b53_spi_of_match[] = { -+ { .compatible = "brcm,bcm5325" }, -+ { .compatible = "brcm,bcm5365" }, -+ { .compatible = "brcm,bcm5395" }, -+ { .compatible = "brcm,bcm5397" }, -+ { .compatible = "brcm,bcm5398" }, -+ { .compatible = "brcm,bcm53115" }, -+ { .compatible = "brcm,bcm53125" }, -+ { .compatible = "brcm,bcm53128" }, -+ { /* sentinel */ } -+}; -+ - static struct spi_driver b53_spi_driver = { - .driver = { - .name = "b53-switch", -+ .of_match_table = b53_spi_of_match, - }, - .probe = b53_spi_probe, - .remove = b53_spi_remove, diff --git a/target/linux/generic/backport-5.10/790-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch b/target/linux/generic/backport-5.10/790-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch deleted file mode 100644 index 99eced1b6a..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0003-net-dsa-b53-relax-is63xx-condition.patch +++ /dev/null @@ -1,31 +0,0 @@ -From ad426d7d966b525b73ed5a1842dd830312bbba71 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= -Date: Wed, 17 Mar 2021 09:42:01 +0100 -Subject: [PATCH] net: dsa: b53: relax is63xx() condition -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -BCM63xx switches are present on bcm63xx and bmips devices. - -Signed-off-by: Álvaro Fernández Rojas -Acked-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_priv.h | 4 ---- - 1 file changed, 4 deletions(-) - ---- a/drivers/net/dsa/b53/b53_priv.h -+++ b/drivers/net/dsa/b53/b53_priv.h -@@ -186,11 +186,7 @@ static inline int is531x5(struct b53_dev - - static inline int is63xx(struct b53_device *dev) - { --#ifdef CONFIG_BCM63XX - return dev->chip_id == BCM63XX_DEVICE_ID; --#else -- return 0; --#endif - } - - static inline int is5301x(struct b53_device *dev) diff --git a/target/linux/generic/backport-5.10/790-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch b/target/linux/generic/backport-5.10/790-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch deleted file mode 100644 index 3b7d8f37cd..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0004-net-dsa-tag_brcm-add-support-for-legacy-tags.patch +++ /dev/null @@ -1,180 +0,0 @@ -From 964dbf186eaa84d409c359ddf09c827a3fbe8228 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= -Date: Wed, 17 Mar 2021 11:29:26 +0100 -Subject: [PATCH] net: dsa: tag_brcm: add support for legacy tags -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM. -These tags are used on BCM5325, BCM5365 and BCM63xx switches. - -Signed-off-by: Álvaro Fernández Rojas -Signed-off-by: David S. Miller ---- - include/net/dsa.h | 2 + - net/dsa/Kconfig | 7 +++ - net/dsa/tag_brcm.c | 107 +++++++++++++++++++++++++++++++++++++++++++-- - 3 files changed, 113 insertions(+), 3 deletions(-) - ---- a/include/net/dsa.h -+++ b/include/net/dsa.h -@@ -45,10 +45,12 @@ struct phylink_link_state; - #define DSA_TAG_PROTO_OCELOT_VALUE 15 - #define DSA_TAG_PROTO_AR9331_VALUE 16 - #define DSA_TAG_PROTO_RTL4_A_VALUE 17 -+#define DSA_TAG_PROTO_BRCM_LEGACY_VALUE 22 - - enum dsa_tag_protocol { - DSA_TAG_PROTO_NONE = DSA_TAG_PROTO_NONE_VALUE, - DSA_TAG_PROTO_BRCM = DSA_TAG_PROTO_BRCM_VALUE, -+ DSA_TAG_PROTO_BRCM_LEGACY = DSA_TAG_PROTO_BRCM_LEGACY_VALUE, - DSA_TAG_PROTO_BRCM_PREPEND = DSA_TAG_PROTO_BRCM_PREPEND_VALUE, - DSA_TAG_PROTO_DSA = DSA_TAG_PROTO_DSA_VALUE, - DSA_TAG_PROTO_EDSA = DSA_TAG_PROTO_EDSA_VALUE, ---- a/net/dsa/Kconfig -+++ b/net/dsa/Kconfig -@@ -47,6 +47,13 @@ config NET_DSA_TAG_BRCM - Say Y if you want to enable support for tagging frames for the - Broadcom switches which place the tag after the MAC source address. - -+config NET_DSA_TAG_BRCM_LEGACY -+ tristate "Tag driver for Broadcom legacy switches using in-frame headers" -+ select NET_DSA_TAG_BRCM_COMMON -+ help -+ Say Y if you want to enable support for tagging frames for the -+ Broadcom legacy switches which place the tag after the MAC source -+ address. - - config NET_DSA_TAG_BRCM_PREPEND - tristate "Tag driver for Broadcom switches using prepended headers" ---- a/net/dsa/tag_brcm.c -+++ b/net/dsa/tag_brcm.c -@@ -11,9 +11,26 @@ - - #include "dsa_priv.h" - --/* This tag length is 4 bytes, older ones were 6 bytes, we do not -- * handle them -- */ -+/* Legacy Broadcom tag (6 bytes) */ -+#define BRCM_LEG_TAG_LEN 6 -+ -+/* Type fields */ -+/* 1st byte in the tag */ -+#define BRCM_LEG_TYPE_HI 0x88 -+/* 2nd byte in the tag */ -+#define BRCM_LEG_TYPE_LO 0x74 -+ -+/* Tag fields */ -+/* 3rd byte in the tag */ -+#define BRCM_LEG_UNICAST (0 << 5) -+#define BRCM_LEG_MULTICAST (1 << 5) -+#define BRCM_LEG_EGRESS (2 << 5) -+#define BRCM_LEG_INGRESS (3 << 5) -+ -+/* 6th byte in the tag */ -+#define BRCM_LEG_PORT_ID (0xf) -+ -+/* Newer Broadcom tag (4 bytes) */ - #define BRCM_TAG_LEN 4 - - /* Tag is constructed and desconstructed using byte by byte access -@@ -194,6 +211,87 @@ DSA_TAG_DRIVER(brcm_netdev_ops); - MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_BRCM); - #endif - -+#if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_LEGACY) -+static struct sk_buff *brcm_leg_tag_xmit(struct sk_buff *skb, -+ struct net_device *dev) -+{ -+ struct dsa_port *dp = dsa_slave_to_port(dev); -+ u8 *brcm_tag; -+ -+ /* The Ethernet switch we are interfaced with needs packets to be at -+ * least 64 bytes (including FCS) otherwise they will be discarded when -+ * they enter the switch port logic. When Broadcom tags are enabled, we -+ * need to make sure that packets are at least 70 bytes -+ * (including FCS and tag) because the length verification is done after -+ * the Broadcom tag is stripped off the ingress packet. -+ * -+ * Let dsa_slave_xmit() free the SKB -+ */ -+ if (__skb_put_padto(skb, ETH_ZLEN + BRCM_LEG_TAG_LEN, false)) -+ return NULL; -+ -+ skb_push(skb, BRCM_LEG_TAG_LEN); -+ -+ memmove(skb->data, skb->data + BRCM_LEG_TAG_LEN, 2 * ETH_ALEN); -+ -+ brcm_tag = skb->data + 2 * ETH_ALEN; -+ -+ /* Broadcom tag type */ -+ brcm_tag[0] = BRCM_LEG_TYPE_HI; -+ brcm_tag[1] = BRCM_LEG_TYPE_LO; -+ -+ /* Broadcom tag value */ -+ brcm_tag[2] = BRCM_LEG_EGRESS; -+ brcm_tag[3] = 0; -+ brcm_tag[4] = 0; -+ brcm_tag[5] = dp->index & BRCM_LEG_PORT_ID; -+ -+ return skb; -+} -+ -+static struct sk_buff *brcm_leg_tag_rcv(struct sk_buff *skb, -+ struct net_device *dev, -+ struct packet_type *pt) -+{ -+ int source_port; -+ u8 *brcm_tag; -+ -+ if (unlikely(!pskb_may_pull(skb, BRCM_LEG_PORT_ID))) -+ return NULL; -+ -+ brcm_tag = skb->data - 2; -+ -+ source_port = brcm_tag[5] & BRCM_LEG_PORT_ID; -+ -+ skb->dev = dsa_master_find_slave(dev, 0, source_port); -+ if (!skb->dev) -+ return NULL; -+ -+ /* Remove Broadcom tag and update checksum */ -+ skb_pull_rcsum(skb, BRCM_LEG_TAG_LEN); -+ -+ skb->offload_fwd_mark = 1; -+ -+ /* Move the Ethernet DA and SA */ -+ memmove(skb->data - ETH_HLEN, -+ skb->data - ETH_HLEN - BRCM_LEG_TAG_LEN, -+ 2 * ETH_ALEN); -+ -+ return skb; -+} -+ -+static const struct dsa_device_ops brcm_legacy_netdev_ops = { -+ .name = "brcm-legacy", -+ .proto = DSA_TAG_PROTO_BRCM_LEGACY, -+ .xmit = brcm_leg_tag_xmit, -+ .rcv = brcm_leg_tag_rcv, -+ .overhead = BRCM_LEG_TAG_LEN, -+}; -+ -+DSA_TAG_DRIVER(brcm_legacy_netdev_ops); -+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_BRCM_LEGACY); -+#endif /* CONFIG_NET_DSA_TAG_BRCM_LEGACY */ -+ - #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_PREPEND) - static struct sk_buff *brcm_tag_xmit_prepend(struct sk_buff *skb, - struct net_device *dev) -@@ -226,6 +324,9 @@ static struct dsa_tag_driver *dsa_tag_dr - #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM) - &DSA_TAG_DRIVER_NAME(brcm_netdev_ops), - #endif -+#if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_LEGACY) -+ &DSA_TAG_DRIVER_NAME(brcm_legacy_netdev_ops), -+#endif - #if IS_ENABLED(CONFIG_NET_DSA_TAG_BRCM_PREPEND) - &DSA_TAG_DRIVER_NAME(brcm_prepend_netdev_ops), - #endif diff --git a/target/linux/generic/backport-5.10/790-v5.13-0005-net-dsa-b53-support-legacy-tags.patch b/target/linux/generic/backport-5.10/790-v5.13-0005-net-dsa-b53-support-legacy-tags.patch deleted file mode 100644 index 838e78a057..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0005-net-dsa-b53-support-legacy-tags.patch +++ /dev/null @@ -1,53 +0,0 @@ -From 46c5176c586c81306bf9e7024c13b95da775490f Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= -Date: Wed, 17 Mar 2021 11:29:27 +0100 -Subject: [PATCH] net: dsa: b53: support legacy tags -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -These tags are used on BCM5325, BCM5365 and BCM63xx switches. - -Signed-off-by: Álvaro Fernández Rojas -Acked-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/Kconfig | 1 + - drivers/net/dsa/b53/b53_common.c | 12 +++++++----- - 2 files changed, 8 insertions(+), 5 deletions(-) - ---- a/drivers/net/dsa/b53/Kconfig -+++ b/drivers/net/dsa/b53/Kconfig -@@ -3,6 +3,7 @@ menuconfig B53 - tristate "Broadcom BCM53xx managed switch support" - depends on NET_DSA - select NET_DSA_TAG_BRCM -+ select NET_DSA_TAG_BRCM_LEGACY - select NET_DSA_TAG_BRCM_PREPEND - help - This driver adds support for Broadcom managed switch chips. It supports ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -2024,15 +2024,17 @@ enum dsa_tag_protocol b53_get_tag_protoc - { - struct b53_device *dev = ds->priv; - -- /* Older models (5325, 5365) support a different tag format that we do -- * not support in net/dsa/tag_brcm.c yet. -- */ -- if (is5325(dev) || is5365(dev) || -- !b53_can_enable_brcm_tags(ds, port, mprot)) { -+ if (!b53_can_enable_brcm_tags(ds, port, mprot)) { - dev->tag_protocol = DSA_TAG_PROTO_NONE; - goto out; - } - -+ /* Older models require a different 6 byte tag */ -+ if (is5325(dev) || is5365(dev) || is63xx(dev)) { -+ dev->tag_protocol = DSA_TAG_PROTO_BRCM_LEGACY; -+ goto out; -+ } -+ - /* Broadcom BCM58xx chips have a flow accelerator on Port 8 - * which requires us to use the prepended Broadcom tag type - */ diff --git a/target/linux/generic/backport-5.10/790-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch b/target/linux/generic/backport-5.10/790-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch deleted file mode 100644 index c1014b20bc..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0006-net-dsa-b53-mmap-Add-device-tree-support.patch +++ /dev/null @@ -1,92 +0,0 @@ -From a5538a777b73b35750ed1ffff8c1ef539e861624 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= -Date: Wed, 17 Mar 2021 10:23:17 +0100 -Subject: [PATCH] net: dsa: b53: mmap: Add device tree support -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Add device tree support to b53_mmap.c while keeping platform devices support. - -Signed-off-by: Álvaro Fernández Rojas -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_mmap.c | 55 ++++++++++++++++++++++++++++++++++ - 1 file changed, 55 insertions(+) - ---- a/drivers/net/dsa/b53/b53_mmap.c -+++ b/drivers/net/dsa/b53/b53_mmap.c -@@ -16,6 +16,7 @@ - * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. - */ - -+#include - #include - #include - #include -@@ -228,11 +229,65 @@ static const struct b53_io_ops b53_mmap_ - .write64 = b53_mmap_write64, - }; - -+static int b53_mmap_probe_of(struct platform_device *pdev, -+ struct b53_platform_data **ppdata) -+{ -+ struct device_node *np = pdev->dev.of_node; -+ struct device_node *of_ports, *of_port; -+ struct device *dev = &pdev->dev; -+ struct b53_platform_data *pdata; -+ void __iomem *mem; -+ -+ mem = devm_platform_ioremap_resource(pdev, 0); -+ if (IS_ERR(mem)) -+ return PTR_ERR(mem); -+ -+ pdata = devm_kzalloc(dev, sizeof(struct b53_platform_data), -+ GFP_KERNEL); -+ if (!pdata) -+ return -ENOMEM; -+ -+ pdata->regs = mem; -+ pdata->chip_id = BCM63XX_DEVICE_ID; -+ pdata->big_endian = of_property_read_bool(np, "big-endian"); -+ -+ of_ports = of_get_child_by_name(np, "ports"); -+ if (!of_ports) { -+ dev_err(dev, "no ports child node found\n"); -+ return -EINVAL; -+ } -+ -+ for_each_available_child_of_node(of_ports, of_port) { -+ u32 reg; -+ -+ if (of_property_read_u32(of_port, "reg", ®)) -+ continue; -+ -+ if (reg < B53_CPU_PORT) -+ pdata->enabled_ports |= BIT(reg); -+ } -+ -+ of_node_put(of_ports); -+ *ppdata = pdata; -+ -+ return 0; -+} -+ - static int b53_mmap_probe(struct platform_device *pdev) - { -+ struct device_node *np = pdev->dev.of_node; - struct b53_platform_data *pdata = pdev->dev.platform_data; - struct b53_mmap_priv *priv; - struct b53_device *dev; -+ int ret; -+ -+ if (!pdata && np) { -+ ret = b53_mmap_probe_of(pdev, &pdata); -+ if (ret) { -+ dev_err(&pdev->dev, "OF probe error\n"); -+ return ret; -+ } -+ } - - if (!pdata) - return -EINVAL; diff --git a/target/linux/generic/backport-5.10/790-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch b/target/linux/generic/backport-5.10/790-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch deleted file mode 100644 index ea36755732..0000000000 --- a/target/linux/generic/backport-5.10/790-v5.13-0007-net-dsa-b53-spi-add-missing-MODULE_DEVICE_TABLE.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 866f1577ba69bde2b9f36c300f603596c7d84a62 Mon Sep 17 00:00:00 2001 -From: Qinglang Miao -Date: Thu, 25 Mar 2021 17:19:54 +0800 -Subject: [PATCH] net: dsa: b53: spi: add missing MODULE_DEVICE_TABLE - -This patch adds missing MODULE_DEVICE_TABLE definition which generates -correct modalias for automatic loading of this driver when it is built -as an external module. - -Reported-by: Hulk Robot -Signed-off-by: Qinglang Miao -Acked-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_spi.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/drivers/net/dsa/b53/b53_spi.c -+++ b/drivers/net/dsa/b53/b53_spi.c -@@ -335,6 +335,7 @@ static const struct of_device_id b53_spi - { .compatible = "brcm,bcm53128" }, - { /* sentinel */ } - }; -+MODULE_DEVICE_TABLE(of, b53_spi_of_match); - - static struct spi_driver b53_spi_driver = { - .driver = { diff --git a/target/linux/generic/backport-5.10/791-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch b/target/linux/generic/backport-5.10/791-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch deleted file mode 100644 index 2a8def39b8..0000000000 --- a/target/linux/generic/backport-5.10/791-v5.14-0001-net-dsa-b53-Do-not-force-CPU-to-be-always-tagged.patch +++ /dev/null @@ -1,86 +0,0 @@ -From 2c32a3d3c233b855943677609fe388f82b1f0975 Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Tue, 8 Jun 2021 14:22:04 -0700 -Subject: [PATCH] net: dsa: b53: Do not force CPU to be always tagged - -Commit ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all -VLANs") forced the CPU port to be always tagged in any VLAN membership. -This was necessary back then because we did not support Broadcom tags -for all configurations so the only way to differentiate tagged and -untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU -port into being always tagged. - -With most configurations enabling Broadcom tags, especially after -8fab459e69ab ("net: dsa: b53: Enable Broadcom tags for 531x5/539x -families") we do not need to apply this unconditional force tagging of -the CPU port in all VLANs. - -A helper function is introduced to faciliate the encapsulation of the -specific condition requiring the CPU port to be tagged in all VLANs and -the dsa_switch_ops::untag_bridge_pvid boolean is moved to when -dsa_switch_ops::setup is called when we have already determined the -tagging protocol we will be using. - -Reported-by: Matthew Hagan -Signed-off-by: Florian Fainelli -Reviewed-by: Vladimir Oltean -Tested-by: Matthew Hagan -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_common.c | 17 ++++++++++++++--- - 1 file changed, 14 insertions(+), 3 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -1049,6 +1049,11 @@ static int b53_setup(struct dsa_switch * - unsigned int port; - int ret; - -+ /* Request bridge PVID untagged when DSA_TAG_PROTO_NONE is set -+ * which forces the CPU port to be tagged in all VLANs. -+ */ -+ ds->untag_bridge_pvid = dev->tag_protocol == DSA_TAG_PROTO_NONE; -+ - ret = b53_reset_switch(dev); - if (ret) { - dev_err(ds->dev, "failed to reset switch\n"); -@@ -1423,6 +1428,13 @@ int b53_vlan_prepare(struct dsa_switch * - return 0; - } - EXPORT_SYMBOL(b53_vlan_prepare); -+ -+static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) -+{ -+ struct b53_device *dev = ds->priv; -+ -+ return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); -+} - - void b53_vlan_add(struct dsa_switch *ds, int port, - const struct switchdev_obj_port_vlan *vlan) -@@ -1442,7 +1454,7 @@ void b53_vlan_add(struct dsa_switch *ds, - untagged = true; - - vl->members |= BIT(port); -- if (untagged && !dsa_is_cpu_port(ds, port)) -+ if (untagged && !b53_vlan_port_needs_forced_tagged(ds, port)) - vl->untag |= BIT(port); - else - vl->untag &= ~BIT(port); -@@ -1480,7 +1492,7 @@ int b53_vlan_del(struct dsa_switch *ds, - if (pvid == vid) - pvid = b53_default_pvid(dev); - -- if (untagged && !dsa_is_cpu_port(ds, port)) -+ if (untagged && !b53_vlan_port_needs_forced_tagged(ds, port)) - vl->untag &= ~(BIT(port)); - - b53_set_vlan_entry(dev, vid, vl); -@@ -2644,7 +2656,6 @@ struct b53_device *b53_switch_alloc(stru - dev->ops = ops; - ds->ops = &b53_switch_ops; - ds->configure_vlan_while_not_filtering = true; -- ds->untag_bridge_pvid = true; - dev->vlan_enabled = ds->configure_vlan_while_not_filtering; - /* Let DSA handle the case were multiple bridges span the same switch - * device and different VLAN awareness settings are requested, which diff --git a/target/linux/generic/backport-5.10/791-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch b/target/linux/generic/backport-5.10/791-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch deleted file mode 100644 index ee3a71ffa5..0000000000 --- a/target/linux/generic/backport-5.10/791-v5.14-0002-net-dsa-b53-remove-redundant-null-check-on-dev.patch +++ /dev/null @@ -1,30 +0,0 @@ -From 11b57faf951cd3a570e3d9e463fc7c41023bc8c6 Mon Sep 17 00:00:00 2001 -From: Colin Ian King -Date: Tue, 15 Jun 2021 10:05:16 +0100 -Subject: [PATCH] net: dsa: b53: remove redundant null check on dev - -The pointer dev can never be null, the null check is redundant -and can be removed. Cleans up a static analysis warning that -pointer priv is dereferencing dev before dev is being null -checked. - -Addresses-Coverity: ("Dereference before null check") -Signed-off-by: Colin Ian King -Acked-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_srab.c | 3 +-- - 1 file changed, 1 insertion(+), 2 deletions(-) - ---- a/drivers/net/dsa/b53/b53_srab.c -+++ b/drivers/net/dsa/b53/b53_srab.c -@@ -632,8 +632,7 @@ static int b53_srab_remove(struct platfo - struct b53_srab_priv *priv = dev->priv; - - b53_srab_intr_set(priv, false); -- if (dev) -- b53_switch_remove(dev); -+ b53_switch_remove(dev); - - return 0; - } diff --git a/target/linux/generic/backport-5.10/791-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch b/target/linux/generic/backport-5.10/791-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch deleted file mode 100644 index df891d68ab..0000000000 --- a/target/linux/generic/backport-5.10/791-v5.14-0003-net-dsa-b53-Create-default-VLAN-entry-explicitly.patch +++ /dev/null @@ -1,71 +0,0 @@ -From 64a81b24487f0d2fba0f033029eec2abc7d82cee Mon Sep 17 00:00:00 2001 -From: Florian Fainelli -Date: Mon, 21 Jun 2021 15:10:55 -0700 -Subject: [PATCH] net: dsa: b53: Create default VLAN entry explicitly - -In case CONFIG_VLAN_8021Q is not set, there will be no call down to the -b53 driver to ensure that the default PVID VLAN entry will be configured -with the appropriate untagged attribute towards the CPU port. We were -implicitly relying on dsa_slave_vlan_rx_add_vid() to do that for us, -instead make it explicit. - -Reported-by: Vladimir Oltean -Signed-off-by: Florian Fainelli -Reviewed-by: Vladimir Oltean -Signed-off-by: David S. Miller ---- - drivers/net/dsa/b53/b53_common.c | 27 +++++++++++++++++++-------- - 1 file changed, 19 insertions(+), 8 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -693,6 +693,13 @@ static u16 b53_default_pvid(struct b53_d - return 0; - } - -+static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) -+{ -+ struct b53_device *dev = ds->priv; -+ -+ return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); -+} -+ - int b53_configure_vlan(struct dsa_switch *ds) - { - struct b53_device *dev = ds->priv; -@@ -713,9 +720,20 @@ int b53_configure_vlan(struct dsa_switch - - b53_enable_vlan(dev, -1, dev->vlan_enabled, ds->vlan_filtering); - -- b53_for_each_port(dev, i) -+ /* Create an untagged VLAN entry for the default PVID in case -+ * CONFIG_VLAN_8021Q is disabled and there are no calls to -+ * dsa_slave_vlan_rx_add_vid() to create the default VLAN -+ * entry. Do this only when the tagging protocol is not -+ * DSA_TAG_PROTO_NONE -+ */ -+ b53_for_each_port(dev, i) { -+ v = &dev->vlans[def_vid]; -+ v->members |= BIT(i); -+ if (!b53_vlan_port_needs_forced_tagged(ds, i)) -+ v->untag = v->members; - b53_write16(dev, B53_VLAN_PAGE, - B53_VLAN_PORT_DEF_TAG(i), def_vid); -+ } - - /* Upon initial call we have not set-up any VLANs, but upon - * system resume, we need to restore all VLAN entries. -@@ -1429,13 +1447,6 @@ int b53_vlan_prepare(struct dsa_switch * - } - EXPORT_SYMBOL(b53_vlan_prepare); - --static bool b53_vlan_port_needs_forced_tagged(struct dsa_switch *ds, int port) --{ -- struct b53_device *dev = ds->priv; -- -- return dev->tag_protocol == DSA_TAG_PROTO_NONE && dsa_is_cpu_port(ds, port); --} -- - void b53_vlan_add(struct dsa_switch *ds, int port, - const struct switchdev_obj_port_vlan *vlan) - { diff --git a/target/linux/generic/backport-5.10/792-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch b/target/linux/generic/backport-5.10/792-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch deleted file mode 100644 index 16aa0711ad..0000000000 --- a/target/linux/generic/backport-5.10/792-v5.16-net-phy-at803x-add-support-for-qca-8327-internal-phy.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 0ccf8511182436183c031e8a2f740ae91a02c625 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Tue, 14 Sep 2021 14:33:45 +0200 -Subject: net: phy: at803x: add support for qca 8327 internal phy - -Add support for qca8327 internal phy needed for correct init of the -switch port. It does use the same qca8337 function and reg just with a -different id. - -Signed-off-by: Ansuel Smith -Tested-by: Rosen Penev -Tested-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 15 +++++++++++++++ - 1 file changed, 15 insertions(+) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -1328,6 +1328,19 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -+}, { -+ /* QCA8327 */ -+ .phy_id = QCA8327_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "QCA PHY 8327", -+ /* PHY_GBIT_FEATURES */ -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, - }, }; - - module_phy_driver(at803x_driver); -@@ -1338,6 +1351,8 @@ static struct mdio_device_id __maybe_unu - { PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) }, - { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, - { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, -+ { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) }, -+ { PHY_ID_MATCH_EXACT(QCA8327_PHY_ID) }, - { } - }; - diff --git a/target/linux/generic/backport-5.10/793-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch b/target/linux/generic/backport-5.10/793-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch deleted file mode 100644 index d80b5db714..0000000000 --- a/target/linux/generic/backport-5.10/793-v5.16-0001-net-dsa-b53-Include-all-ports-in-enabled_ports.patch +++ /dev/null @@ -1,131 +0,0 @@ -From 983d96a9116a328668601555d96736261d33170c Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Thu, 16 Sep 2021 14:03:51 +0200 -Subject: [PATCH] net: dsa: b53: Include all ports in "enabled_ports" -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Make "enabled_ports" bitfield contain all available switch ports -including a CPU port. This way there is no need for fixup during -initialization. - -For BCM53010, BCM53018 and BCM53019 include also other available ports. - -Signed-off-by: Rafał Miłecki -Reviewed-by: Florian Fainelli -Tested-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/b53/b53_common.c | 23 +++++++++++------------ - 1 file changed, 11 insertions(+), 12 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -2288,7 +2288,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5325_DEVICE_ID, - .dev_name = "BCM5325", - .vlans = 16, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x3f, - .arl_bins = 2, - .arl_buckets = 1024, - .imp_port = 5, -@@ -2299,7 +2299,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5365_DEVICE_ID, - .dev_name = "BCM5365", - .vlans = 256, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x3f, - .arl_bins = 2, - .arl_buckets = 1024, - .imp_port = 5, -@@ -2310,7 +2310,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5389_DEVICE_ID, - .dev_name = "BCM5389", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x11f, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2324,7 +2324,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5395_DEVICE_ID, - .dev_name = "BCM5395", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x11f, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2338,7 +2338,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5397_DEVICE_ID, - .dev_name = "BCM5397", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x11f, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2352,7 +2352,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM5398_DEVICE_ID, - .dev_name = "BCM5398", - .vlans = 4096, -- .enabled_ports = 0x7f, -+ .enabled_ports = 0x17f, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2366,7 +2366,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM53115_DEVICE_ID, - .dev_name = "BCM53115", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x11f, - .arl_bins = 4, - .arl_buckets = 1024, - .vta_regs = B53_VTA_REGS, -@@ -2380,7 +2380,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM53125_DEVICE_ID, - .dev_name = "BCM53125", - .vlans = 4096, -- .enabled_ports = 0xff, -+ .enabled_ports = 0x1ff, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2422,7 +2422,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM53010_DEVICE_ID, - .dev_name = "BCM53010", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x1bf, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2464,7 +2464,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM53018_DEVICE_ID, - .dev_name = "BCM53018", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x1bf, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2478,7 +2478,7 @@ static const struct b53_chip_data b53_sw - .chip_id = BCM53019_DEVICE_ID, - .dev_name = "BCM53019", - .vlans = 4096, -- .enabled_ports = 0x1f, -+ .enabled_ports = 0x1bf, - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -@@ -2605,7 +2605,6 @@ static int b53_switch_init(struct b53_de - dev->cpu_port = 5; - } - -- dev->enabled_ports |= BIT(dev->cpu_port); - dev->num_ports = fls(dev->enabled_ports); - - dev->ds->num_ports = min_t(unsigned int, dev->num_ports, DSA_MAX_PORTS); diff --git a/target/linux/generic/backport-5.10/793-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch b/target/linux/generic/backport-5.10/793-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch deleted file mode 100644 index 4a4f8e940d..0000000000 --- a/target/linux/generic/backport-5.10/793-v5.16-0002-net-dsa-b53-Drop-BCM5301x-workaround-for-a-wrong-CPU.patch +++ /dev/null @@ -1,42 +0,0 @@ -From b290c6384afabbca5ae6e2af72fb1b2bc37922be Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Thu, 16 Sep 2021 14:03:52 +0200 -Subject: [PATCH] net: dsa: b53: Drop BCM5301x workaround for a wrong CPU/IMP - port -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -On BCM5301x port 8 requires a fixed link when used. - -Years ago when b53 was an OpenWrt downstream driver (with configuration -based on sometimes bugged NVRAM) there was a need for a fixup. In case -of forcing fixed link for (incorrectly specified) port 5 the code had to -actually setup port 8 link. - -For upstream b53 driver with setup based on DT there is no need for that -workaround. In DT we have and require correct ports setup. - -Signed-off-by: Rafał Miłecki -Reviewed-by: Florian Fainelli -Tested-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/b53/b53_common.c | 6 ------ - 1 file changed, 6 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -1256,12 +1256,6 @@ static void b53_adjust_link(struct dsa_s - return; - } - } -- } else if (is5301x(dev)) { -- if (port != dev->cpu_port) { -- b53_force_port_config(dev, dev->cpu_port, 2000, -- DUPLEX_FULL, true, true); -- b53_force_link(dev, dev->cpu_port, 1); -- } - } - - /* Re-negotiate EEE if it was enabled already */ diff --git a/target/linux/generic/backport-5.10/793-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch b/target/linux/generic/backport-5.10/793-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch deleted file mode 100644 index 3954ee4aac..0000000000 --- a/target/linux/generic/backport-5.10/793-v5.16-0003-net-dsa-b53-Improve-flow-control-setup-on-BCM5301x.patch +++ /dev/null @@ -1,32 +0,0 @@ -From 3ff26b29230c54fea2353b63124c589b61953e14 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Thu, 16 Sep 2021 14:03:53 +0200 -Subject: [PATCH] net: dsa: b53: Improve flow control setup on BCM5301x -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -According to the Broadcom's reference driver flow control needs to be -enabled for any CPU switch port (5, 7 or 8 - depending on which one is -used). Current code makes it work only for the port 5. Use -dsa_is_cpu_port() which solved that problem. - -Signed-off-by: Rafał Miłecki -Reviewed-by: Florian Fainelli -Tested-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/b53/b53_common.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -1187,7 +1187,7 @@ static void b53_adjust_link(struct dsa_s - return; - - /* Enable flow control on BCM5301x's CPU port */ -- if (is5301x(dev) && port == dev->cpu_port) -+ if (is5301x(dev) && dsa_is_cpu_port(ds, port)) - tx_pause = rx_pause = true; - - if (phydev->pause) { diff --git a/target/linux/generic/backport-5.10/793-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch b/target/linux/generic/backport-5.10/793-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch deleted file mode 100644 index 9e687b1488..0000000000 --- a/target/linux/generic/backport-5.10/793-v5.16-0004-net-dsa-b53-Drop-unused-cpu_port-field.patch +++ /dev/null @@ -1,205 +0,0 @@ -From 7d5af56418d7d01e43247a33b6fe6492ea871923 Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= -Date: Thu, 16 Sep 2021 14:03:54 +0200 -Subject: [PATCH] net: dsa: b53: Drop unused "cpu_port" field -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -It's set but never used anymore. - -Signed-off-by: Rafał Miłecki -Reviewed-by: Florian Fainelli -Tested-by: Florian Fainelli -Signed-off-by: Jakub Kicinski ---- - drivers/net/dsa/b53/b53_common.c | 28 ---------------------------- - drivers/net/dsa/b53/b53_priv.h | 1 - - 2 files changed, 29 deletions(-) - ---- a/drivers/net/dsa/b53/b53_common.c -+++ b/drivers/net/dsa/b53/b53_common.c -@@ -2286,7 +2286,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 2, - .arl_buckets = 1024, - .imp_port = 5, -- .cpu_port = B53_CPU_PORT_25, - .duplex_reg = B53_DUPLEX_STAT_FE, - }, - { -@@ -2297,7 +2296,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 2, - .arl_buckets = 1024, - .imp_port = 5, -- .cpu_port = B53_CPU_PORT_25, - .duplex_reg = B53_DUPLEX_STAT_FE, - }, - { -@@ -2308,7 +2306,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2322,7 +2319,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2336,7 +2332,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS_9798, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2350,7 +2345,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS_9798, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2365,7 +2359,6 @@ static const struct b53_chip_data b53_sw - .arl_buckets = 1024, - .vta_regs = B53_VTA_REGS, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, - .jumbo_size_reg = B53_JUMBO_MAX_SIZE, -@@ -2378,7 +2371,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2392,7 +2384,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2406,7 +2397,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS_63XX, - .duplex_reg = B53_DUPLEX_STAT_63XX, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK_63XX, -@@ -2420,7 +2410,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2434,7 +2423,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2448,7 +2436,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2462,7 +2449,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2476,7 +2462,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT_25, /* TODO: auto detect */ - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2490,7 +2475,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2504,7 +2488,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2518,7 +2501,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 1024, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2532,7 +2514,6 @@ static const struct b53_chip_data b53_sw - .arl_bins = 4, - .arl_buckets = 256, - .imp_port = 8, -- .cpu_port = B53_CPU_PORT, - .vta_regs = B53_VTA_REGS, - .duplex_reg = B53_DUPLEX_STAT_GE, - .jumbo_pm_reg = B53_JUMBO_PORT_MASK, -@@ -2558,7 +2539,6 @@ static int b53_switch_init(struct b53_de - dev->vta_regs[2] = chip->vta_regs[2]; - dev->jumbo_pm_reg = chip->jumbo_pm_reg; - dev->imp_port = chip->imp_port; -- dev->cpu_port = chip->cpu_port; - dev->num_vlans = chip->vlans; - dev->num_arl_bins = chip->arl_bins; - dev->num_arl_buckets = chip->arl_buckets; -@@ -2590,13 +2570,6 @@ static int b53_switch_init(struct b53_de - break; - #endif - } -- } else if (dev->chip_id == BCM53115_DEVICE_ID) { -- u64 strap_value; -- -- b53_read48(dev, B53_STAT_PAGE, B53_STRAP_VALUE, &strap_value); -- /* use second IMP port if GMII is enabled */ -- if (strap_value & SV_GMII_CTRL_115) -- dev->cpu_port = 5; - } - - dev->num_ports = fls(dev->enabled_ports); ---- a/drivers/net/dsa/b53/b53_priv.h -+++ b/drivers/net/dsa/b53/b53_priv.h -@@ -123,7 +123,6 @@ struct b53_device { - /* used ports mask */ - u16 enabled_ports; - unsigned int imp_port; -- unsigned int cpu_port; - - /* connect specific data */ - u8 current_page; diff --git a/target/linux/generic/backport-5.10/794-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch b/target/linux/generic/backport-5.10/794-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch deleted file mode 100644 index ab4fdf8509..0000000000 --- a/target/linux/generic/backport-5.10/794-v5.15-net-dsa-don-t-set-skb-offload_fwd_mark-when-not-offl.patch +++ /dev/null @@ -1,138 +0,0 @@ -From bea7907837c57a0aaac009931eb14efb056dafab Mon Sep 17 00:00:00 2001 -From: Vladimir Oltean -Date: Thu, 29 Jul 2021 17:56:00 +0300 -Subject: [PATCH] net: dsa: don't set skb->offload_fwd_mark when not offloading - the bridge - -DSA has gained the recent ability to deal gracefully with upper -interfaces it cannot offload, such as the bridge, bonding or team -drivers. When such uppers exist, the ports are still in standalone mode -as far as the hardware is concerned. - -But when we deliver packets to the software bridge in order for that to -do the forwarding, there is an unpleasant surprise in that the bridge -will refuse to forward them. This is because we unconditionally set -skb->offload_fwd_mark = true, meaning that the bridge thinks the frames -were already forwarded in hardware by us. - -Since dp->bridge_dev is populated only when there is hardware offload -for it, but not in the software fallback case, let's introduce a new -helper that can be called from the tagger data path which sets the -skb->offload_fwd_mark accordingly to zero when there is no hardware -offload for bridging. This lets the bridge forward packets back to other -interfaces of our switch, if needed. - -Signed-off-by: Vladimir Oltean -Reviewed-by: Tobias Waldekranz -Signed-off-by: David S. Miller ---- - net/dsa/dsa_priv.h | 14 ++++++++++++++ - net/dsa/tag_brcm.c | 4 ++-- - net/dsa/tag_dsa.c | 15 +++++++++++---- - net/dsa/tag_ksz.c | 2 +- - net/dsa/tag_lan9303.c | 3 ++- - net/dsa/tag_mtk.c | 2 +- - net/dsa/tag_ocelot.c | 2 +- - net/dsa/tag_rtl4_a.c | 2 +- - net/dsa/tag_sja1105.c | 20 ++++++++++++++------ - 9 files changed, 47 insertions(+), 17 deletions(-) - ---- a/net/dsa/dsa_priv.h -+++ b/net/dsa/dsa_priv.h -@@ -266,6 +266,20 @@ static inline struct sk_buff *dsa_untag_ - return skb; - } - -+/* If the ingress port offloads the bridge, we mark the frame as autonomously -+ * forwarded by hardware, so the software bridge doesn't forward in twice, back -+ * to us, because we already did. However, if we're in fallback mode and we do -+ * software bridging, we are not offloading it, therefore the dp->bridge_dev -+ * pointer is not populated, and flooding needs to be done by software (we are -+ * effectively operating in standalone ports mode). -+ */ -+static inline void dsa_default_offload_fwd_mark(struct sk_buff *skb) -+{ -+ struct dsa_port *dp = dsa_slave_to_port(skb->dev); -+ -+ skb->offload_fwd_mark = !!(dp->bridge_dev); -+} -+ - /* switch.c */ - int dsa_switch_register_notifier(struct dsa_switch *ds); - void dsa_switch_unregister_notifier(struct dsa_switch *ds); ---- a/net/dsa/tag_brcm.c -+++ b/net/dsa/tag_brcm.c -@@ -166,7 +166,7 @@ static struct sk_buff *brcm_tag_rcv_ll(s - /* Remove Broadcom tag and update checksum */ - skb_pull_rcsum(skb, BRCM_TAG_LEN); - -- skb->offload_fwd_mark = 1; -+ dsa_default_offload_fwd_mark(skb); - - return skb; - } -@@ -270,7 +270,7 @@ static struct sk_buff *brcm_leg_tag_rcv( - /* Remove Broadcom tag and update checksum */ - skb_pull_rcsum(skb, BRCM_LEG_TAG_LEN); - -- skb->offload_fwd_mark = 1; -+ dsa_default_offload_fwd_mark(skb); - - /* Move the Ethernet DA and SA */ - memmove(skb->data - ETH_HLEN, ---- a/net/dsa/tag_ksz.c -+++ b/net/dsa/tag_ksz.c -@@ -24,7 +24,7 @@ static struct sk_buff *ksz_common_rcv(st - - pskb_trim_rcsum(skb, skb->len - len); - -- skb->offload_fwd_mark = true; -+ dsa_default_offload_fwd_mark(skb); - - return skb; - } ---- a/net/dsa/tag_lan9303.c -+++ b/net/dsa/tag_lan9303.c -@@ -115,7 +115,8 @@ static struct sk_buff *lan9303_rcv(struc - skb_pull_rcsum(skb, 2 + 2); - memmove(skb->data - ETH_HLEN, skb->data - (ETH_HLEN + LAN9303_TAG_LEN), - 2 * ETH_ALEN); -- skb->offload_fwd_mark = !(lan9303_tag1 & LAN9303_TAG_RX_TRAPPED_TO_CPU); -+ if (!(lan9303_tag1 & LAN9303_TAG_RX_TRAPPED_TO_CPU)) -+ dsa_default_offload_fwd_mark(skb); - - return skb; - } ---- a/net/dsa/tag_mtk.c -+++ b/net/dsa/tag_mtk.c -@@ -104,7 +104,7 @@ static struct sk_buff *mtk_tag_rcv(struc - - /* Only unicast or broadcast frames are offloaded */ - if (likely(!is_multicast_skb)) -- skb->offload_fwd_mark = 1; -+ dsa_default_offload_fwd_mark(skb); - - return skb; - } ---- a/net/dsa/tag_ocelot.c -+++ b/net/dsa/tag_ocelot.c -@@ -225,7 +225,7 @@ static struct sk_buff *ocelot_rcv(struct - */ - return NULL; - -- skb->offload_fwd_mark = 1; -+ dsa_default_offload_fwd_mark(skb); - skb->priority = qos_class; - - /* Ocelot switches copy frames unmodified to the CPU. However, it is ---- a/net/dsa/tag_rtl4_a.c -+++ b/net/dsa/tag_rtl4_a.c -@@ -115,7 +115,7 @@ static struct sk_buff *rtl4a_tag_rcv(str - skb->data - ETH_HLEN - RTL4_A_HDR_LEN, - 2 * ETH_ALEN); - -- skb->offload_fwd_mark = 1; -+ dsa_default_offload_fwd_mark(skb); - - return skb; - } diff --git a/target/linux/generic/backport-5.10/795-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch b/target/linux/generic/backport-5.10/795-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch deleted file mode 100644 index c82bf913a0..0000000000 --- a/target/linux/generic/backport-5.10/795-v5.16-01-net-phy-at803x-add-support-for-qca-8327-A-variant.patch +++ /dev/null @@ -1,65 +0,0 @@ -From b4df02b562f4aa14ff6811f30e1b4d2159585c59 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 19 Sep 2021 18:28:15 +0200 -Subject: net: phy: at803x: add support for qca 8327 A variant internal phy - -For qca8327 internal phy there are 2 different switch variant with 2 -different phy id. Add this missing variant so the internal phy can be -correctly identified and fixed. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 25 ++++++++++++++++++++----- - 1 file changed, 20 insertions(+), 5 deletions(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -148,7 +148,8 @@ - #define AT803X_PAGE_FIBER 0 - #define AT803X_PAGE_COPPER 1 - --#define QCA8327_PHY_ID 0x004dd034 -+#define QCA8327_A_PHY_ID 0x004dd033 -+#define QCA8327_B_PHY_ID 0x004dd034 - #define QCA8337_PHY_ID 0x004dd036 - #define QCA8K_PHY_ID_MASK 0xffffffff - -@@ -1329,10 +1330,23 @@ static struct phy_driver at803x_driver[] - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, - }, { -- /* QCA8327 */ -- .phy_id = QCA8327_PHY_ID, -+ /* QCA8327-A from switch QCA8327-AL1A */ -+ .phy_id = QCA8327_A_PHY_ID, - .phy_id_mask = QCA8K_PHY_ID_MASK, -- .name = "QCA PHY 8327", -+ .name = "QCA PHY 8327-A", -+ /* PHY_GBIT_FEATURES */ -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, -+}, { -+ /* QCA8327-B from switch QCA8327-BL1A */ -+ .phy_id = QCA8327_B_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "QCA PHY 8327-B", - /* PHY_GBIT_FEATURES */ - .probe = at803x_probe, - .flags = PHY_IS_INTERNAL, -@@ -1352,7 +1366,8 @@ static struct mdio_device_id __maybe_unu - { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, - { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, - { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) }, -- { PHY_ID_MATCH_EXACT(QCA8327_PHY_ID) }, -+ { PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) }, -+ { PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) }, - { } - }; - diff --git a/target/linux/generic/backport-5.10/795-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch b/target/linux/generic/backport-5.10/795-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch deleted file mode 100644 index be24fd5cf7..0000000000 --- a/target/linux/generic/backport-5.10/795-v5.16-02-net-phy-at803x-add-resume-suspend-function-to-qca83x.patch +++ /dev/null @@ -1,45 +0,0 @@ -From 15b9df4ece17d084f14eb0ca1cf05f2ad497e425 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 19 Sep 2021 18:28:16 +0200 -Subject: net: phy: at803x: add resume/suspend function to qca83xx phy - -Add resume/suspend function to qca83xx internal phy. -We can't use the at803x generic function as the documentation lacks of -any support for WoL regs. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 6 ++++++ - 1 file changed, 6 insertions(+) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -1329,6 +1329,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -+ .suspend = genphy_suspend, -+ .resume = genphy_resume, - }, { - /* QCA8327-A from switch QCA8327-AL1A */ - .phy_id = QCA8327_A_PHY_ID, -@@ -1342,6 +1344,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -+ .suspend = genphy_suspend, -+ .resume = genphy_resume, - }, { - /* QCA8327-B from switch QCA8327-BL1A */ - .phy_id = QCA8327_B_PHY_ID, -@@ -1355,6 +1359,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -+ .suspend = genphy_suspend, -+ .resume = genphy_resume, - }, }; - - module_phy_driver(at803x_driver); diff --git a/target/linux/generic/backport-5.10/795-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch b/target/linux/generic/backport-5.10/795-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch deleted file mode 100644 index 23f574c76f..0000000000 --- a/target/linux/generic/backport-5.10/795-v5.16-03-net-phy-at803x-fix-spacing-and-improve-name-for-83xx.patch +++ /dev/null @@ -1,95 +0,0 @@ -From d44fd8604a4ab92119adb35f05fd87612af722b5 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 19 Sep 2021 18:28:17 +0200 -Subject: net: phy: at803x: fix spacing and improve name for 83xx phy - -Fix spacing and improve name for 83xx phy following other phy in the -same driver. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 60 ++++++++++++++++++++++++------------------------ - 1 file changed, 30 insertions(+), 30 deletions(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -1318,47 +1318,47 @@ static struct phy_driver at803x_driver[] - .config_aneg = at803x_config_aneg, - }, { - /* QCA8337 */ -- .phy_id = QCA8337_PHY_ID, -- .phy_id_mask = QCA8K_PHY_ID_MASK, -- .name = "QCA PHY 8337", -+ .phy_id = QCA8337_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "Qualcomm Atheros 8337 internal PHY", - /* PHY_GBIT_FEATURES */ -- .probe = at803x_probe, -- .flags = PHY_IS_INTERNAL, -- .config_init = qca83xx_config_init, -- .soft_reset = genphy_soft_reset, -- .get_sset_count = at803x_get_sset_count, -- .get_strings = at803x_get_strings, -- .get_stats = at803x_get_stats, -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, - .suspend = genphy_suspend, - .resume = genphy_resume, - }, { - /* QCA8327-A from switch QCA8327-AL1A */ -- .phy_id = QCA8327_A_PHY_ID, -- .phy_id_mask = QCA8K_PHY_ID_MASK, -- .name = "QCA PHY 8327-A", -+ .phy_id = QCA8327_A_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "Qualcomm Atheros 8327-A internal PHY", - /* PHY_GBIT_FEATURES */ -- .probe = at803x_probe, -- .flags = PHY_IS_INTERNAL, -- .config_init = qca83xx_config_init, -- .soft_reset = genphy_soft_reset, -- .get_sset_count = at803x_get_sset_count, -- .get_strings = at803x_get_strings, -- .get_stats = at803x_get_stats, -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, - .suspend = genphy_suspend, - .resume = genphy_resume, - }, { - /* QCA8327-B from switch QCA8327-BL1A */ -- .phy_id = QCA8327_B_PHY_ID, -- .phy_id_mask = QCA8K_PHY_ID_MASK, -- .name = "QCA PHY 8327-B", -+ .phy_id = QCA8327_B_PHY_ID, -+ .phy_id_mask = QCA8K_PHY_ID_MASK, -+ .name = "Qualcomm Atheros 8327-B internal PHY", - /* PHY_GBIT_FEATURES */ -- .probe = at803x_probe, -- .flags = PHY_IS_INTERNAL, -- .config_init = qca83xx_config_init, -- .soft_reset = genphy_soft_reset, -- .get_sset_count = at803x_get_sset_count, -- .get_strings = at803x_get_strings, -- .get_stats = at803x_get_stats, -+ .probe = at803x_probe, -+ .flags = PHY_IS_INTERNAL, -+ .config_init = qca83xx_config_init, -+ .soft_reset = genphy_soft_reset, -+ .get_sset_count = at803x_get_sset_count, -+ .get_strings = at803x_get_strings, -+ .get_stats = at803x_get_stats, - .suspend = genphy_suspend, - .resume = genphy_resume, - }, }; diff --git a/target/linux/generic/backport-5.10/796-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch b/target/linux/generic/backport-5.10/796-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch deleted file mode 100644 index 5dfe27dd24..0000000000 --- a/target/linux/generic/backport-5.10/796-v5.16-01-net-phy-at803x-fix-resume-for-QCA8327-phy.patch +++ /dev/null @@ -1,131 +0,0 @@ -From ba3c01ee02ed0d821c9f241f179bbc9457542b8f Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 10 Oct 2021 00:46:15 +0200 -Subject: net: phy: at803x: fix resume for QCA8327 phy - -From Documentation phy resume triggers phy reset and restart -auto-negotiation. Add a dedicated function to wait reset to finish as -it was notice a regression where port sometime are not reliable after a -suspend/resume session. The reset wait logic is copied from phy_poll_reset. -Add dedicated suspend function to use genphy_suspend only with QCA8337 -phy and set only additional debug settings for QCA8327. With more test -it was reported that QCA8327 doesn't proprely support this mode and -using this cause the unreliability of the switch ports, especially the -malfunction of the port0. - -Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy") -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 69 +++++++++++++++++++++++++++++++++++++++++++----- - 1 file changed, 63 insertions(+), 6 deletions(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -92,9 +92,14 @@ - #define AT803X_DEBUG_REG_5 0x05 - #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) - -+#define AT803X_DEBUG_REG_HIB_CTRL 0x0b -+#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10) -+#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13) -+ - #define AT803X_DEBUG_REG_3C 0x3C - - #define AT803X_DEBUG_REG_3D 0x3D -+#define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6) - - #define AT803X_DEBUG_REG_1F 0x1F - #define AT803X_DEBUG_PLL_ON BIT(2) -@@ -1220,6 +1225,58 @@ static int qca83xx_config_init(struct ph - return 0; - } - -+static int qca83xx_resume(struct phy_device *phydev) -+{ -+ int ret, val; -+ -+ /* Skip reset if not suspended */ -+ if (!phydev->suspended) -+ return 0; -+ -+ /* Reinit the port, reset values set by suspend */ -+ qca83xx_config_init(phydev); -+ -+ /* Reset the port on port resume */ -+ phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE); -+ -+ /* On resume from suspend the switch execute a reset and -+ * restart auto-negotiation. Wait for reset to complete. -+ */ -+ ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET), -+ 50000, 600000, true); -+ if (ret) -+ return ret; -+ -+ msleep(1); -+ -+ return 0; -+} -+ -+static int qca83xx_suspend(struct phy_device *phydev) -+{ -+ u16 mask = 0; -+ -+ /* Only QCA8337 support actual suspend. -+ * QCA8327 cause port unreliability when phy suspend -+ * is set. -+ */ -+ if (phydev->drv->phy_id == QCA8337_PHY_ID) { -+ genphy_suspend(phydev); -+ } else { -+ mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX); -+ phy_modify(phydev, MII_BMCR, mask, 0); -+ } -+ -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_3D, -+ AT803X_DEBUG_GATE_CLK_IN1000, 0); -+ -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, -+ AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE | -+ AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0); -+ -+ return 0; -+} -+ - static struct phy_driver at803x_driver[] = { - { - /* Qualcomm Atheros AR8035 */ -@@ -1329,8 +1386,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -- .suspend = genphy_suspend, -- .resume = genphy_resume, -+ .suspend = qca83xx_suspend, -+ .resume = qca83xx_resume, - }, { - /* QCA8327-A from switch QCA8327-AL1A */ - .phy_id = QCA8327_A_PHY_ID, -@@ -1344,8 +1401,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -- .suspend = genphy_suspend, -- .resume = genphy_resume, -+ .suspend = qca83xx_suspend, -+ .resume = qca83xx_resume, - }, { - /* QCA8327-B from switch QCA8327-BL1A */ - .phy_id = QCA8327_B_PHY_ID, -@@ -1359,8 +1416,8 @@ static struct phy_driver at803x_driver[] - .get_sset_count = at803x_get_sset_count, - .get_strings = at803x_get_strings, - .get_stats = at803x_get_stats, -- .suspend = genphy_suspend, -- .resume = genphy_resume, -+ .suspend = qca83xx_suspend, -+ .resume = qca83xx_resume, - }, }; - - module_phy_driver(at803x_driver); diff --git a/target/linux/generic/backport-5.10/796-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch b/target/linux/generic/backport-5.10/796-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch deleted file mode 100644 index aeb43e2f67..0000000000 --- a/target/linux/generic/backport-5.10/796-v5.16-02-net-phy-at803x-add-DAC-amplitude-fix-for-8327-phy.patch +++ /dev/null @@ -1,91 +0,0 @@ -From 1ca8311949aec5c9447645731ef1c6bc5bd71350 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 10 Oct 2021 00:46:16 +0200 -Subject: net: phy: at803x: add DAC amplitude fix for 8327 phy - -QCA8327 internal phy require DAC amplitude adjustement set to +6% with -100m speed. Also add additional define to report a change of the same -reg in QCA8337. (different scope it does set 1000m voltage) -Add link_change_notify function to set the proper amplitude adjustement -on PHY_RUNNING state and disable on any other state. - -Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy") -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 33 +++++++++++++++++++++++++++++++++ - 1 file changed, 33 insertions(+) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -87,6 +87,8 @@ - #define AT803X_PSSR_MR_AN_COMPLETE 0x0200 - - #define AT803X_DEBUG_REG_0 0x00 -+#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) -+#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) - #define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) - - #define AT803X_DEBUG_REG_5 0x05 -@@ -1222,9 +1224,37 @@ static int qca83xx_config_init(struct ph - break; - } - -+ /* QCA8327 require DAC amplitude adjustment for 100m set to +6%. -+ * Disable on init and enable only with 100m speed following -+ * qca original source code. -+ */ -+ if (phydev->drv->phy_id == QCA8327_A_PHY_ID || -+ phydev->drv->phy_id == QCA8327_B_PHY_ID) -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ QCA8327_DEBUG_MANU_CTRL_EN, 0); -+ - return 0; - } - -+static void qca83xx_link_change_notify(struct phy_device *phydev) -+{ -+ /* QCA8337 doesn't require DAC Amplitude adjustement */ -+ if (phydev->drv->phy_id == QCA8337_PHY_ID) -+ return; -+ -+ /* Set DAC Amplitude adjustment to +6% for 100m on link running */ -+ if (phydev->state == PHY_RUNNING) { -+ if (phydev->speed == SPEED_100) -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ QCA8327_DEBUG_MANU_CTRL_EN, -+ QCA8327_DEBUG_MANU_CTRL_EN); -+ } else { -+ /* Reset DAC Amplitude adjustment */ -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ QCA8327_DEBUG_MANU_CTRL_EN, 0); -+ } -+} -+ - static int qca83xx_resume(struct phy_device *phydev) - { - int ret, val; -@@ -1379,6 +1409,7 @@ static struct phy_driver at803x_driver[] - .phy_id_mask = QCA8K_PHY_ID_MASK, - .name = "Qualcomm Atheros 8337 internal PHY", - /* PHY_GBIT_FEATURES */ -+ .link_change_notify = qca83xx_link_change_notify, - .probe = at803x_probe, - .flags = PHY_IS_INTERNAL, - .config_init = qca83xx_config_init, -@@ -1394,6 +1425,7 @@ static struct phy_driver at803x_driver[] - .phy_id_mask = QCA8K_PHY_ID_MASK, - .name = "Qualcomm Atheros 8327-A internal PHY", - /* PHY_GBIT_FEATURES */ -+ .link_change_notify = qca83xx_link_change_notify, - .probe = at803x_probe, - .flags = PHY_IS_INTERNAL, - .config_init = qca83xx_config_init, -@@ -1409,6 +1441,7 @@ static struct phy_driver at803x_driver[] - .phy_id_mask = QCA8K_PHY_ID_MASK, - .name = "Qualcomm Atheros 8327-B internal PHY", - /* PHY_GBIT_FEATURES */ -+ .link_change_notify = qca83xx_link_change_notify, - .probe = at803x_probe, - .flags = PHY_IS_INTERNAL, - .config_init = qca83xx_config_init, diff --git a/target/linux/generic/backport-5.10/796-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch b/target/linux/generic/backport-5.10/796-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch deleted file mode 100644 index 2352fa0e44..0000000000 --- a/target/linux/generic/backport-5.10/796-v5.16-03-net-phy-at803x-enable-prefer-master-for-83xx-interna.patch +++ /dev/null @@ -1,27 +0,0 @@ -From 9d1c29b4028557a496be9c5eb2b4b86063700636 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 10 Oct 2021 00:46:17 +0200 -Subject: net: phy: at803x: enable prefer master for 83xx internal phy - -From original QCA source code the port was set to prefer master as port -type in 1000BASE-T mode. Apply the same settings also here. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -1233,6 +1233,9 @@ static int qca83xx_config_init(struct ph - at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, - QCA8327_DEBUG_MANU_CTRL_EN, 0); - -+ /* Following original QCA sourcecode set port to prefer master */ -+ phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER); -+ - return 0; - } - diff --git a/target/linux/generic/backport-5.10/796-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch b/target/linux/generic/backport-5.10/796-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch deleted file mode 100644 index 9c28a893f1..0000000000 --- a/target/linux/generic/backport-5.10/796-v5.16-04-net-phy-at803x-better-describe-debug-regs.patch +++ /dev/null @@ -1,127 +0,0 @@ -From 67999555ff42e91de7654488d9a7735bd9e84555 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 10 Oct 2021 00:46:18 +0200 -Subject: net: phy: at803x: better describe debug regs - -Give a name to known debug regs from Documentation instead of using -unknown hex values. - -Signed-off-by: Ansuel Smith -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - drivers/net/phy/at803x.c | 30 +++++++++++++++--------------- - 1 file changed, 15 insertions(+), 15 deletions(-) - ---- a/drivers/net/phy/at803x.c -+++ b/drivers/net/phy/at803x.c -@@ -86,12 +86,12 @@ - #define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/ - #define AT803X_PSSR_MR_AN_COMPLETE 0x0200 - --#define AT803X_DEBUG_REG_0 0x00 -+#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00 - #define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) - #define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) - #define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) - --#define AT803X_DEBUG_REG_5 0x05 -+#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05 - #define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) - - #define AT803X_DEBUG_REG_HIB_CTRL 0x0b -@@ -100,7 +100,7 @@ - - #define AT803X_DEBUG_REG_3C 0x3C - --#define AT803X_DEBUG_REG_3D 0x3D -+#define AT803X_DEBUG_REG_GREEN 0x3D - #define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6) - - #define AT803X_DEBUG_REG_1F 0x1F -@@ -274,25 +274,25 @@ static int at803x_read_page(struct phy_d - - static int at803x_enable_rx_delay(struct phy_device *phydev) - { -- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, -+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0, - AT803X_DEBUG_RX_CLK_DLY_EN); - } - - static int at803x_enable_tx_delay(struct phy_device *phydev) - { -- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0, -+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0, - AT803X_DEBUG_TX_CLK_DLY_EN); - } - - static int at803x_disable_rx_delay(struct phy_device *phydev) - { -- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, - AT803X_DEBUG_RX_CLK_DLY_EN, 0); - } - - static int at803x_disable_tx_delay(struct phy_device *phydev) - { -- return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, -+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, - AT803X_DEBUG_TX_CLK_DLY_EN, 0); - } - -@@ -1208,9 +1208,9 @@ static int qca83xx_config_init(struct ph - switch (switch_revision) { - case 1: - /* For 100M waveform */ -- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_0, 0x02ea); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea); - /* Turn on Gigabit clock */ -- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x68a0); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0); - break; - - case 2: -@@ -1218,8 +1218,8 @@ static int qca83xx_config_init(struct ph - fallthrough; - case 4: - phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f); -- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3D, 0x6860); -- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_5, 0x2c46); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860); -+ at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46); - at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000); - break; - } -@@ -1230,7 +1230,7 @@ static int qca83xx_config_init(struct ph - */ - if (phydev->drv->phy_id == QCA8327_A_PHY_ID || - phydev->drv->phy_id == QCA8327_B_PHY_ID) -- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, - QCA8327_DEBUG_MANU_CTRL_EN, 0); - - /* Following original QCA sourcecode set port to prefer master */ -@@ -1248,12 +1248,12 @@ static void qca83xx_link_change_notify(s - /* Set DAC Amplitude adjustment to +6% for 100m on link running */ - if (phydev->state == PHY_RUNNING) { - if (phydev->speed == SPEED_100) -- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, - QCA8327_DEBUG_MANU_CTRL_EN, - QCA8327_DEBUG_MANU_CTRL_EN); - } else { - /* Reset DAC Amplitude adjustment */ -- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, - QCA8327_DEBUG_MANU_CTRL_EN, 0); - } - } -@@ -1300,7 +1300,7 @@ static int qca83xx_suspend(struct phy_de - phy_modify(phydev, MII_BMCR, mask, 0); - } - -- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_3D, -+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN, - AT803X_DEBUG_GATE_CLK_IN1000, 0); - - at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, diff --git a/target/linux/generic/backport-5.10/797-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch b/target/linux/generic/backport-5.10/797-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch deleted file mode 100644 index c8d424de38..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-01-dsa-qca8k-add-mac-power-sel-support.patch +++ /dev/null @@ -1,80 +0,0 @@ -From d8b6f5bae6d3b648a67b6958cb98e4e97256d652 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:06 +0200 -Subject: dsa: qca8k: add mac_power_sel support - -Add missing mac power sel support needed for ipq8064/5 SoC that require -1.8v for the internal regulator port instead of the default 1.5v. -If other device needs this, consider adding a dedicated binding to -support this. - -Signed-off-by: Ansuel Smith -Reviewed-by: Vladimir Oltean -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 31 +++++++++++++++++++++++++++++++ - drivers/net/dsa/qca8k.h | 5 +++++ - 2 files changed, 36 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -951,6 +951,33 @@ qca8k_setup_of_rgmii_delay(struct qca8k_ - } - - static int -+qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv) -+{ -+ u32 mask = 0; -+ int ret = 0; -+ -+ /* SoC specific settings for ipq8064. -+ * If more device require this consider adding -+ * a dedicated binding. -+ */ -+ if (of_machine_is_compatible("qcom,ipq8064")) -+ mask |= QCA8K_MAC_PWR_RGMII0_1_8V; -+ -+ /* SoC specific settings for ipq8065 */ -+ if (of_machine_is_compatible("qcom,ipq8065")) -+ mask |= QCA8K_MAC_PWR_RGMII1_1_8V; -+ -+ if (mask) { -+ ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL, -+ QCA8K_MAC_PWR_RGMII0_1_8V | -+ QCA8K_MAC_PWR_RGMII1_1_8V, -+ mask); -+ } -+ -+ return ret; -+} -+ -+static int - qca8k_setup(struct dsa_switch *ds) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -@@ -979,6 +1006,10 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - -+ ret = qca8k_setup_mac_pwr_sel(priv); -+ if (ret) -+ return ret; -+ - /* Enable CPU Port */ - ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0, - QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -100,6 +100,11 @@ - #define QCA8K_SGMII_MODE_CTRL_PHY (1 << 22) - #define QCA8K_SGMII_MODE_CTRL_MAC (2 << 22) - -+/* MAC_PWR_SEL registers */ -+#define QCA8K_REG_MAC_PWR_SEL 0x0e4 -+#define QCA8K_MAC_PWR_RGMII1_1_8V BIT(18) -+#define QCA8K_MAC_PWR_RGMII0_1_8V BIT(19) -+ - /* EEE control registers */ - #define QCA8K_REG_EEE_CTRL 0x100 - #define QCA8K_REG_EEE_CTRL_LPI_EN(_i) ((_i + 1) * 2) diff --git a/target/linux/generic/backport-5.10/797-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch b/target/linux/generic/backport-5.10/797-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch deleted file mode 100644 index bd768ec27d..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-02-dt-bindings-net-dsa-qca8k-Add-SGMII-clock-phase-prop.patch +++ /dev/null @@ -1,30 +0,0 @@ -From fdbf35df9c091db9c46e57e9938e3f7a4f603a7c Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:07 +0200 -Subject: dt-bindings: net: dsa: qca8k: Add SGMII clock phase properties - -Add names and descriptions of additional PORT0_PAD_CTRL properties. -qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock -phase to failling edge. - -Co-developed-by: Matthew Hagan -Signed-off-by: Matthew Hagan -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -37,6 +37,10 @@ A CPU port node has the following option - managed entity. See - Documentation/devicetree/bindings/net/fixed-link.txt - for details. -+- qca,sgmii-rxclk-falling-edge: Set the receive clock phase to falling edge. -+ Mostly used in qca8327 with CPU port 0 set to -+ sgmii. -+- qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. - - For QCA8K the 'fixed-link' sub-node supports only the following properties: - diff --git a/target/linux/generic/backport-5.10/797-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch b/target/linux/generic/backport-5.10/797-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch deleted file mode 100644 index e464452d82..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-03-net-dsa-qca8k-add-support-for-sgmii-falling-edge.patch +++ /dev/null @@ -1,127 +0,0 @@ -From 6c43809bf1bee76c434e365a26546a92a5fbec14 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:08 +0200 -Subject: net: dsa: qca8k: add support for sgmii falling edge - -Add support for this in the qca8k driver. Also add support for SGMII -rx/tx clock falling edge. This is only present for pad0, pad5 and -pad6 have these bit reserved from Documentation. Add a comment that this -is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and -setting falling in port0 applies to both configuration with sgmii used -for port0 or port6. - -Co-developed-by: Matthew Hagan -Signed-off-by: Matthew Hagan -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 63 +++++++++++++++++++++++++++++++++++++++++++++++++ - drivers/net/dsa/qca8k.h | 4 ++++ - 2 files changed, 67 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -978,6 +978,42 @@ qca8k_setup_mac_pwr_sel(struct qca8k_pri - } - - static int -+qca8k_parse_port_config(struct qca8k_priv *priv) -+{ -+ struct device_node *port_dn; -+ phy_interface_t mode; -+ struct dsa_port *dp; -+ int port, ret; -+ -+ /* We have 2 CPU port. Check them */ -+ for (port = 0; port < QCA8K_NUM_PORTS; port++) { -+ /* Skip every other port */ -+ if (port != 0 && port != 6) -+ continue; -+ -+ dp = dsa_to_port(priv->ds, port); -+ port_dn = dp->dn; -+ -+ if (!of_device_is_available(port_dn)) -+ continue; -+ -+ ret = of_get_phy_mode(port_dn, &mode); -+ if (ret) -+ continue; -+ -+ if (mode == PHY_INTERFACE_MODE_SGMII) { -+ if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) -+ priv->sgmii_tx_clk_falling_edge = true; -+ -+ if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) -+ priv->sgmii_rx_clk_falling_edge = true; -+ } -+ } -+ -+ return 0; -+} -+ -+static int - qca8k_setup(struct dsa_switch *ds) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -@@ -990,6 +1026,11 @@ qca8k_setup(struct dsa_switch *ds) - return -EINVAL; - } - -+ /* Parse CPU port config to be later used in phy_link mac_config */ -+ ret = qca8k_parse_port_config(priv); -+ if (ret) -+ return ret; -+ - mutex_init(&priv->reg_mutex); - - /* Start by setting up the register mapping */ -@@ -1274,6 +1315,28 @@ qca8k_phylink_mac_config(struct dsa_swit - } - - qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val); -+ -+ /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and -+ * falling edge is set writing in the PORT0 PAD reg -+ */ -+ if (priv->switch_id == QCA8K_ID_QCA8327 || -+ priv->switch_id == QCA8K_ID_QCA8337) -+ reg = QCA8K_REG_PORT0_PAD_CTRL; -+ -+ val = 0; -+ -+ /* SGMII Clock phase configuration */ -+ if (priv->sgmii_rx_clk_falling_edge) -+ val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE; -+ -+ if (priv->sgmii_tx_clk_falling_edge) -+ val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE; -+ -+ if (val) -+ ret = qca8k_rmw(priv, reg, -+ QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE | -+ QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, -+ val); - break; - default: - dev_err(ds->dev, "xMII mode %s not supported for port %d\n", ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -35,6 +35,8 @@ - #define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8) - #define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8) - #define QCA8K_REG_PORT0_PAD_CTRL 0x004 -+#define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19) -+#define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18) - #define QCA8K_REG_PORT5_PAD_CTRL 0x008 - #define QCA8K_REG_PORT6_PAD_CTRL 0x00c - #define QCA8K_PORT_PAD_RGMII_EN BIT(26) -@@ -260,6 +262,8 @@ struct qca8k_priv { - u8 switch_revision; - u8 rgmii_tx_delay; - u8 rgmii_rx_delay; -+ bool sgmii_rx_clk_falling_edge; -+ bool sgmii_tx_clk_falling_edge; - bool legacy_phy_port_mapping; - struct regmap *regmap; - struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/797-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch b/target/linux/generic/backport-5.10/797-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch deleted file mode 100644 index 606ac0af3d..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-04-dt-bindings-net-dsa-qca8k-Document-support-for-CPU-p.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 731d613338ec6de482053ffa3f71be2325b0f8eb Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:09 +0200 -Subject: dt-bindings: net: dsa: qca8k: Document support for CPU port 6 - -The switch now support CPU port to be set 6 instead of be hardcoded to -0. Document support for it and describe logic selection. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 6 +++++- - 1 file changed, 5 insertions(+), 1 deletion(-) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -29,7 +29,11 @@ the mdio MASTER is used as communication - Don't use mixed external and internal mdio-bus configurations, as this is - not supported by the hardware. - --The CPU port of this switch is always port 0. -+This switch support 2 CPU port. Normally and advised configuration is with -+CPU port set to port 0. It is also possible to set the CPU port to port 6 -+if the device requires it. The driver will configure the switch to the defined -+port. With both CPU port declared the first CPU port is selected as primary -+and the secondary CPU ignored. - - A CPU port node has the following optional node: - diff --git a/target/linux/generic/backport-5.10/797-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch b/target/linux/generic/backport-5.10/797-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch deleted file mode 100644 index 320db8fa9f..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-05-net-dsa-qca8k-add-support-for-cpu-port-6.patch +++ /dev/null @@ -1,153 +0,0 @@ -From 3fcf734aa482487df83cf8f18608438fcf59127f Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:10 +0200 -Subject: net: dsa: qca8k: add support for cpu port 6 - -Currently CPU port is always hardcoded to port 0. This switch have 2 CPU -ports. The original intention of this driver seems to be use the -mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration -where device have connected only the CPU port 6. To skip the -introduction of a new binding, rework the driver to address the -secondary CPU port as primary and drop any reference of hardcoded port. -With configuration of mac06 exchange, just skip the definition of port0 -and define the CPU port as a secondary. The driver will autoconfigure -the switch to use that as the primary CPU port. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 51 ++++++++++++++++++++++++++++++++++--------------- - drivers/net/dsa/qca8k.h | 2 -- - 2 files changed, 36 insertions(+), 17 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -977,6 +977,22 @@ qca8k_setup_mac_pwr_sel(struct qca8k_pri - return ret; - } - -+static int qca8k_find_cpu_port(struct dsa_switch *ds) -+{ -+ struct qca8k_priv *priv = ds->priv; -+ -+ /* Find the connected cpu port. Valid port are 0 or 6 */ -+ if (dsa_is_cpu_port(ds, 0)) -+ return 0; -+ -+ dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6"); -+ -+ if (dsa_is_cpu_port(ds, 6)) -+ return 6; -+ -+ return -EINVAL; -+} -+ - static int - qca8k_parse_port_config(struct qca8k_priv *priv) - { -@@ -1017,13 +1033,13 @@ static int - qca8k_setup(struct dsa_switch *ds) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -- int ret, i; -+ int cpu_port, ret, i; - u32 mask; - -- /* Make sure that port 0 is the cpu port */ -- if (!dsa_is_cpu_port(ds, 0)) { -- dev_err(priv->dev, "port 0 is not the CPU port"); -- return -EINVAL; -+ cpu_port = qca8k_find_cpu_port(ds); -+ if (cpu_port < 0) { -+ dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6"); -+ return cpu_port; - } - - /* Parse CPU port config to be later used in phy_link mac_config */ -@@ -1065,7 +1081,7 @@ qca8k_setup(struct dsa_switch *ds) - dev_warn(priv->dev, "mib init failed"); - - /* Enable QCA header mode on the cpu port */ -- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT), -+ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(cpu_port), - QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | - QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); - if (ret) { -@@ -1087,10 +1103,10 @@ qca8k_setup(struct dsa_switch *ds) - - /* Forward all unknown frames to CPU port for Linux processing */ - ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | -- BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); -+ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | -+ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | -+ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S | -+ BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S); - if (ret) - return ret; - -@@ -1098,7 +1114,7 @@ qca8k_setup(struct dsa_switch *ds) - for (i = 0; i < QCA8K_NUM_PORTS; i++) { - /* CPU port gets connected to all user ports of the switch */ - if (dsa_is_cpu_port(ds, i)) { -- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT), -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port), - QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); - if (ret) - return ret; -@@ -1110,7 +1126,7 @@ qca8k_setup(struct dsa_switch *ds) - - ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), - QCA8K_PORT_LOOKUP_MEMBER, -- BIT(QCA8K_CPU_PORT)); -+ BIT(cpu_port)); - if (ret) - return ret; - -@@ -1616,9 +1632,12 @@ static int - qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -- int port_mask = BIT(QCA8K_CPU_PORT); -+ int port_mask, cpu_port; - int i, ret; - -+ cpu_port = dsa_to_port(ds, port)->cpu_dp->index; -+ port_mask = BIT(cpu_port); -+ - for (i = 1; i < QCA8K_NUM_PORTS; i++) { - if (dsa_to_port(ds, i)->bridge_dev != br) - continue; -@@ -1645,7 +1664,9 @@ static void - qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) - { - struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; -- int i; -+ int cpu_port, i; -+ -+ cpu_port = dsa_to_port(ds, port)->cpu_dp->index; - - for (i = 1; i < QCA8K_NUM_PORTS; i++) { - if (dsa_to_port(ds, i)->bridge_dev != br) -@@ -1662,7 +1683,7 @@ qca8k_port_bridge_leave(struct dsa_switc - * this port - */ - qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), -- QCA8K_PORT_LOOKUP_MEMBER, BIT(QCA8K_CPU_PORT)); -+ QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port)); - } - - static int ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -24,8 +24,6 @@ - - #define QCA8K_NUM_FDB_RECORDS 2048 - --#define QCA8K_CPU_PORT 0 -- - #define QCA8K_PORT_VID_DEF 1 - - /* Global control registers */ diff --git a/target/linux/generic/backport-5.10/797-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch b/target/linux/generic/backport-5.10/797-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch deleted file mode 100644 index de201764f9..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-06-net-dsa-qca8k-rework-rgmii-delay-logic-and-scan-for-.patch +++ /dev/null @@ -1,295 +0,0 @@ -From 5654ec78dd7e64b1e04777b24007344329e6a63b Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:11 +0200 -Subject: net: dsa: qca8k: rework rgmii delay logic and scan for cpu port 6 - -Future proof commit. This switch have 2 CPU ports and one valid -configuration is first CPU port set to sgmii and second CPU port set to -rgmii-id. The current implementation detects delay only for CPU port -zero set to rgmii and doesn't count any delay set in a secondary CPU -port. Drop the current delay scan function and move it to the sgmii -parser function to generalize and implicitly add support for secondary -CPU port set to rgmii-id. Introduce new logic where delay is enabled -also with internal delay binding declared and rgmii set as PHY mode. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 165 ++++++++++++++++++++++++------------------------ - drivers/net/dsa/qca8k.h | 10 ++- - 2 files changed, 89 insertions(+), 86 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -889,68 +889,6 @@ qca8k_setup_mdio_bus(struct qca8k_priv * - } - - static int --qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv) --{ -- struct device_node *port_dn; -- phy_interface_t mode; -- struct dsa_port *dp; -- u32 val; -- -- /* CPU port is already checked */ -- dp = dsa_to_port(priv->ds, 0); -- -- port_dn = dp->dn; -- -- /* Check if port 0 is set to the correct type */ -- of_get_phy_mode(port_dn, &mode); -- if (mode != PHY_INTERFACE_MODE_RGMII_ID && -- mode != PHY_INTERFACE_MODE_RGMII_RXID && -- mode != PHY_INTERFACE_MODE_RGMII_TXID) { -- return 0; -- } -- -- switch (mode) { -- case PHY_INTERFACE_MODE_RGMII_ID: -- case PHY_INTERFACE_MODE_RGMII_RXID: -- if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val)) -- val = 2; -- else -- /* Switch regs accept value in ns, convert ps to ns */ -- val = val / 1000; -- -- if (val > QCA8K_MAX_DELAY) { -- dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); -- val = 3; -- } -- -- priv->rgmii_rx_delay = val; -- /* Stop here if we need to check only for rx delay */ -- if (mode != PHY_INTERFACE_MODE_RGMII_ID) -- break; -- -- fallthrough; -- case PHY_INTERFACE_MODE_RGMII_TXID: -- if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val)) -- val = 1; -- else -- /* Switch regs accept value in ns, convert ps to ns */ -- val = val / 1000; -- -- if (val > QCA8K_MAX_DELAY) { -- dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); -- val = 3; -- } -- -- priv->rgmii_tx_delay = val; -- break; -- default: -- return 0; -- } -- -- return 0; --} -- --static int - qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv) - { - u32 mask = 0; -@@ -996,19 +934,21 @@ static int qca8k_find_cpu_port(struct ds - static int - qca8k_parse_port_config(struct qca8k_priv *priv) - { -+ int port, cpu_port_index = 0, ret; - struct device_node *port_dn; - phy_interface_t mode; - struct dsa_port *dp; -- int port, ret; -+ u32 delay; - - /* We have 2 CPU port. Check them */ -- for (port = 0; port < QCA8K_NUM_PORTS; port++) { -+ for (port = 0; port < QCA8K_NUM_PORTS && cpu_port_index < QCA8K_NUM_CPU_PORTS; port++) { - /* Skip every other port */ - if (port != 0 && port != 6) - continue; - - dp = dsa_to_port(priv->ds, port); - port_dn = dp->dn; -+ cpu_port_index++; - - if (!of_device_is_available(port_dn)) - continue; -@@ -1017,12 +957,54 @@ qca8k_parse_port_config(struct qca8k_pri - if (ret) - continue; - -- if (mode == PHY_INTERFACE_MODE_SGMII) { -+ switch (mode) { -+ case PHY_INTERFACE_MODE_RGMII: -+ case PHY_INTERFACE_MODE_RGMII_ID: -+ case PHY_INTERFACE_MODE_RGMII_TXID: -+ case PHY_INTERFACE_MODE_RGMII_RXID: -+ delay = 0; -+ -+ if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay)) -+ /* Switch regs accept value in ns, convert ps to ns */ -+ delay = delay / 1000; -+ else if (mode == PHY_INTERFACE_MODE_RGMII_ID || -+ mode == PHY_INTERFACE_MODE_RGMII_TXID) -+ delay = 1; -+ -+ if (delay > QCA8K_MAX_DELAY) { -+ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); -+ delay = 3; -+ } -+ -+ priv->rgmii_tx_delay[cpu_port_index] = delay; -+ -+ delay = 0; -+ -+ if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay)) -+ /* Switch regs accept value in ns, convert ps to ns */ -+ delay = delay / 1000; -+ else if (mode == PHY_INTERFACE_MODE_RGMII_ID || -+ mode == PHY_INTERFACE_MODE_RGMII_RXID) -+ delay = 2; -+ -+ if (delay > QCA8K_MAX_DELAY) { -+ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); -+ delay = 3; -+ } -+ -+ priv->rgmii_rx_delay[cpu_port_index] = delay; -+ -+ break; -+ case PHY_INTERFACE_MODE_SGMII: - if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) - priv->sgmii_tx_clk_falling_edge = true; - - if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) - priv->sgmii_rx_clk_falling_edge = true; -+ -+ break; -+ default: -+ continue; - } - } - -@@ -1059,10 +1041,6 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - -- ret = qca8k_setup_of_rgmii_delay(priv); -- if (ret) -- return ret; -- - ret = qca8k_setup_mac_pwr_sel(priv); - if (ret) - return ret; -@@ -1229,8 +1207,8 @@ qca8k_phylink_mac_config(struct dsa_swit - const struct phylink_link_state *state) - { - struct qca8k_priv *priv = ds->priv; -- u32 reg, val; -- int ret; -+ int cpu_port_index, ret; -+ u32 reg, val, delay; - - switch (port) { - case 0: /* 1st CPU port */ -@@ -1242,6 +1220,7 @@ qca8k_phylink_mac_config(struct dsa_swit - return; - - reg = QCA8K_REG_PORT0_PAD_CTRL; -+ cpu_port_index = QCA8K_CPU_PORT0; - break; - case 1: - case 2: -@@ -1260,6 +1239,7 @@ qca8k_phylink_mac_config(struct dsa_swit - return; - - reg = QCA8K_REG_PORT6_PAD_CTRL; -+ cpu_port_index = QCA8K_CPU_PORT6; - break; - default: - dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); -@@ -1274,23 +1254,40 @@ qca8k_phylink_mac_config(struct dsa_swit - - switch (state->interface) { - case PHY_INTERFACE_MODE_RGMII: -- /* RGMII mode means no delay so don't enable the delay */ -- qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); -- break; - case PHY_INTERFACE_MODE_RGMII_ID: - case PHY_INTERFACE_MODE_RGMII_TXID: - case PHY_INTERFACE_MODE_RGMII_RXID: -- /* RGMII_ID needs internal delay. This is enabled through -- * PORT5_PAD_CTRL for all ports, rather than individual port -- * registers -+ val = QCA8K_PORT_PAD_RGMII_EN; -+ -+ /* Delay can be declared in 3 different way. -+ * Mode to rgmii and internal-delay standard binding defined -+ * rgmii-id or rgmii-tx/rx phy mode set. -+ * The parse logic set a delay different than 0 only when one -+ * of the 3 different way is used. In all other case delay is -+ * not enabled. With ID or TX/RXID delay is enabled and set -+ * to the default and recommended value. -+ */ -+ if (priv->rgmii_tx_delay[cpu_port_index]) { -+ delay = priv->rgmii_tx_delay[cpu_port_index]; -+ -+ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | -+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; -+ } -+ -+ if (priv->rgmii_rx_delay[cpu_port_index]) { -+ delay = priv->rgmii_rx_delay[cpu_port_index]; -+ -+ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; -+ } -+ -+ /* Set RGMII delay based on the selected values */ -+ qca8k_write(priv, reg, val); -+ -+ /* QCA8337 requires to set rgmii rx delay for all ports. -+ * This is enabled through PORT5_PAD_CTRL for all ports, -+ * rather than individual port registers. - */ -- qca8k_write(priv, reg, -- QCA8K_PORT_PAD_RGMII_EN | -- QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) | -- QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) | -- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | -- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); -- /* QCA8337 requires to set rgmii rx delay */ - if (priv->switch_id == QCA8K_ID_QCA8337) - qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, - QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -13,6 +13,7 @@ - #include - - #define QCA8K_NUM_PORTS 7 -+#define QCA8K_NUM_CPU_PORTS 2 - #define QCA8K_MAX_MTU 9000 - - #define PHY_ID_QCA8327 0x004dd034 -@@ -255,13 +256,18 @@ struct qca8k_match_data { - u8 id; - }; - -+enum { -+ QCA8K_CPU_PORT0, -+ QCA8K_CPU_PORT6, -+}; -+ - struct qca8k_priv { - u8 switch_id; - u8 switch_revision; -- u8 rgmii_tx_delay; -- u8 rgmii_rx_delay; - bool sgmii_rx_clk_falling_edge; - bool sgmii_tx_clk_falling_edge; -+ u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ -+ u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ - bool legacy_phy_port_mapping; - struct regmap *regmap; - struct mii_bus *bus; diff --git a/target/linux/generic/backport-5.10/797-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch b/target/linux/generic/backport-5.10/797-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch deleted file mode 100644 index 8abd264e79..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-07-dt-bindings-net-dsa-qca8k-Document-qca-sgmii-enable-.patch +++ /dev/null @@ -1,33 +0,0 @@ -From 13ad5ccc093ff448b99ac7e138e91e78796adb48 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:12 +0200 -Subject: dt-bindings: net: dsa: qca8k: Document qca,sgmii-enable-pll - -Document qca,sgmii-enable-pll binding used in the CPU nodes to -enable SGMII PLL on MAC config. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -45,6 +45,16 @@ A CPU port node has the following option - Mostly used in qca8327 with CPU port 0 set to - sgmii. - - qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. -+- qca,sgmii-enable-pll : For SGMII CPU port, explicitly enable PLL, TX and RX -+ chain along with Signal Detection. -+ This should NOT be enabled for qca8327. If enabled with -+ qca8327 the sgmii port won't correctly init and an err -+ is printed. -+ This can be required for qca8337 switch with revision 2. -+ A warning is displayed when used with revision greater -+ 2. -+ With CPU port set to sgmii and qca8337 it is advised -+ to set this unless a communication problem is observed. - - For QCA8K the 'fixed-link' sub-node supports only the following properties: - diff --git a/target/linux/generic/backport-5.10/797-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch b/target/linux/generic/backport-5.10/797-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch deleted file mode 100644 index 2b5a84a1b0..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-08-net-dsa-qca8k-add-explicit-SGMII-PLL-enable.patch +++ /dev/null @@ -1,65 +0,0 @@ -From bbc4799e8bb6c397e3b3fec13de68e179f5db9ff Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:13 +0200 -Subject: net: dsa: qca8k: add explicit SGMII PLL enable - -Support enabling PLL on the SGMII CPU port. Some device require this -special configuration or no traffic is transmitted and the switch -doesn't work at all. A dedicated binding is added to the CPU node -port to apply the correct reg on mac config. -Fail to correctly configure sgmii with qca8327 switch and warn if pll is -used on qca8337 with a revision greater than 1. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 19 +++++++++++++++++-- - drivers/net/dsa/qca8k.h | 1 + - 2 files changed, 18 insertions(+), 2 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1002,6 +1002,18 @@ qca8k_parse_port_config(struct qca8k_pri - if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) - priv->sgmii_rx_clk_falling_edge = true; - -+ if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) { -+ priv->sgmii_enable_pll = true; -+ -+ if (priv->switch_id == QCA8K_ID_QCA8327) { -+ dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling"); -+ priv->sgmii_enable_pll = false; -+ } -+ -+ if (priv->switch_revision < 2) -+ dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more."); -+ } -+ - break; - default: - continue; -@@ -1312,8 +1324,11 @@ qca8k_phylink_mac_config(struct dsa_swit - if (ret) - return; - -- val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | -- QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD; -+ val |= QCA8K_SGMII_EN_SD; -+ -+ if (priv->sgmii_enable_pll) -+ val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | -+ QCA8K_SGMII_EN_TX; - - if (dsa_is_cpu_port(ds, port)) { - /* CPU port, we're talking to the CPU MAC, be a PHY */ ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -266,6 +266,7 @@ struct qca8k_priv { - u8 switch_revision; - bool sgmii_rx_clk_falling_edge; - bool sgmii_tx_clk_falling_edge; -+ bool sgmii_enable_pll; - u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ - u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ - bool legacy_phy_port_mapping; diff --git a/target/linux/generic/backport-5.10/797-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch b/target/linux/generic/backport-5.10/797-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch deleted file mode 100644 index 38dc954e8c..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-09-dt-bindings-net-dsa-qca8k-Document-qca-led-open-drai.patch +++ /dev/null @@ -1,37 +0,0 @@ -From 924087c5c3d41553700b0eb83ca2a53b91643dca Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:14 +0200 -Subject: dt-bindings: net: dsa: qca8k: Document qca,led-open-drain binding - -Document new binding qca,ignore-power-on-sel used to ignore -power on strapping and use sw regs instead. -Document qca,led-open.drain to set led to open drain mode, the -qca,ignore-power-on-sel is mandatory with this enabled or an error will -be reported. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 11 +++++++++++ - 1 file changed, 11 insertions(+) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -13,6 +13,17 @@ Required properties: - Optional properties: - - - reset-gpios: GPIO to be used to reset the whole device -+- qca,ignore-power-on-sel: Ignore power on pin strapping to configure led open -+ drain or eeprom presence. This is needed for broken -+ devices that have wrong configuration or when the oem -+ decided to not use pin strapping and fallback to sw -+ regs. -+- qca,led-open-drain: Set leds to open-drain mode. This requires the -+ qca,ignore-power-on-sel to be set or the driver will fail -+ to probe. This is needed if the oem doesn't use pin -+ strapping to set this mode and prefers to set it using sw -+ regs. The pin strapping related to led open drain mode is -+ the pin B68 for QCA832x and B49 for QCA833x - - Subnodes: - diff --git a/target/linux/generic/backport-5.10/797-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch b/target/linux/generic/backport-5.10/797-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch deleted file mode 100644 index aa5d92a4fd..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-10-net-dsa-qca8k-add-support-for-pws-config-reg.patch +++ /dev/null @@ -1,92 +0,0 @@ -From 362bb238d8bf1470424214a8a5968d9c6cce68fa Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:15 +0200 -Subject: net: dsa: qca8k: add support for pws config reg - -Some qca8327 switch require to force the ignore of power on sel -strapping. Some switch require to set the led open drain mode in regs -instead of using strapping. While most of the device implements this -using the correct way using pin strapping, there are still some broken -device that require to be set using sw regs. -Introduce a new binding and support these special configuration. -As led open drain require to ignore pin strapping to work, the probe -fails with EINVAL error with incorrect configuration. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 39 +++++++++++++++++++++++++++++++++++++++ - drivers/net/dsa/qca8k.h | 6 ++++++ - 2 files changed, 45 insertions(+) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -932,6 +932,41 @@ static int qca8k_find_cpu_port(struct ds - } - - static int -+qca8k_setup_of_pws_reg(struct qca8k_priv *priv) -+{ -+ struct device_node *node = priv->dev->of_node; -+ u32 val = 0; -+ int ret; -+ -+ /* QCA8327 require to set to the correct mode. -+ * His bigger brother QCA8328 have the 172 pin layout. -+ * Should be applied by default but we set this just to make sure. -+ */ -+ if (priv->switch_id == QCA8K_ID_QCA8327) { -+ ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN, -+ QCA8327_PWS_PACKAGE148_EN); -+ if (ret) -+ return ret; -+ } -+ -+ if (of_property_read_bool(node, "qca,ignore-power-on-sel")) -+ val |= QCA8K_PWS_POWER_ON_SEL; -+ -+ if (of_property_read_bool(node, "qca,led-open-drain")) { -+ if (!(val & QCA8K_PWS_POWER_ON_SEL)) { -+ dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set."); -+ return -EINVAL; -+ } -+ -+ val |= QCA8K_PWS_LED_OPEN_EN_CSR; -+ } -+ -+ return qca8k_rmw(priv, QCA8K_REG_PWS, -+ QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL, -+ val); -+} -+ -+static int - qca8k_parse_port_config(struct qca8k_priv *priv) - { - int port, cpu_port_index = 0, ret; -@@ -1053,6 +1088,10 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - -+ ret = qca8k_setup_of_pws_reg(priv); -+ if (ret) -+ return ret; -+ - ret = qca8k_setup_mac_pwr_sel(priv); - if (ret) - return ret; ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -46,6 +46,12 @@ - #define QCA8K_MAX_DELAY 3 - #define QCA8K_PORT_PAD_SGMII_EN BIT(7) - #define QCA8K_REG_PWS 0x010 -+#define QCA8K_PWS_POWER_ON_SEL BIT(31) -+/* This reg is only valid for QCA832x and toggle the package -+ * type from 176 pin (by default) to 148 pin used on QCA8327 -+ */ -+#define QCA8327_PWS_PACKAGE148_EN BIT(30) -+#define QCA8K_PWS_LED_OPEN_EN_CSR BIT(24) - #define QCA8K_PWS_SERDES_AEN_DIS BIT(7) - #define QCA8K_REG_MODULE_EN 0x030 - #define QCA8K_MODULE_EN_MIB BIT(0) diff --git a/target/linux/generic/backport-5.10/797-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch b/target/linux/generic/backport-5.10/797-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch deleted file mode 100644 index 1bfb00c5b2..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-11-dt-bindings-net-dsa-qca8k-document-support-for-qca83.patch +++ /dev/null @@ -1,32 +0,0 @@ -From ed7988d77fbfb79366b68f9e7fa60a6080da23d4 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:16 +0200 -Subject: dt-bindings: net: dsa: qca8k: document support for qca8328 - -QCA8328 is the bigger brother of qca8327. Document the new compatible -binding and add some information to understand the various switch -compatible. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/dsa/qca8k.txt | 7 ++++--- - 1 file changed, 4 insertions(+), 3 deletions(-) - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt -@@ -3,9 +3,10 @@ - Required properties: - - - compatible: should be one of: -- "qca,qca8327" -- "qca,qca8334" -- "qca,qca8337" -+ "qca,qca8328": referenced as AR8328(N)-AK1(A/B) QFN 176 pin package -+ "qca,qca8327": referenced as AR8327(N)-AL1A DR-QFN 148 pin package -+ "qca,qca8334": referenced as QCA8334-AL3C QFN 88 pin package -+ "qca,qca8337": referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package - - - #size-cells: must be 0 - - #address-cells: must be 1 diff --git a/target/linux/generic/backport-5.10/797-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch b/target/linux/generic/backport-5.10/797-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch deleted file mode 100644 index 6e118f5a14..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-12-net-dsa-qca8k-add-support-for-QCA8328.patch +++ /dev/null @@ -1,78 +0,0 @@ -From f477d1c8bdbef4f400718238e350f16f521d2a3e Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:17 +0200 -Subject: net: dsa: qca8k: add support for QCA8328 - -QCA8328 switch is the bigger brother of the qca8327. Same regs different -chip. Change the function to set the correct pin layout and introduce a -new match_data to differentiate the 2 switch as they have the same ID -and their internal PHY have the same ID. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 19 ++++++++++++++++--- - drivers/net/dsa/qca8k.h | 1 + - 2 files changed, 17 insertions(+), 3 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -935,6 +935,7 @@ static int - qca8k_setup_of_pws_reg(struct qca8k_priv *priv) - { - struct device_node *node = priv->dev->of_node; -+ const struct qca8k_match_data *data; - u32 val = 0; - int ret; - -@@ -943,8 +944,14 @@ qca8k_setup_of_pws_reg(struct qca8k_priv - * Should be applied by default but we set this just to make sure. - */ - if (priv->switch_id == QCA8K_ID_QCA8327) { -+ data = of_device_get_match_data(priv->dev); -+ -+ /* Set the correct package of 148 pin for QCA8327 */ -+ if (data->reduced_package) -+ val |= QCA8327_PWS_PACKAGE148_EN; -+ - ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN, -- QCA8327_PWS_PACKAGE148_EN); -+ val); - if (ret) - return ret; - } -@@ -2098,7 +2105,12 @@ static int qca8k_resume(struct device *d - static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, - qca8k_suspend, qca8k_resume); - --static const struct qca8k_match_data qca832x = { -+static const struct qca8k_match_data qca8327 = { -+ .id = QCA8K_ID_QCA8327, -+ .reduced_package = true, -+}; -+ -+static const struct qca8k_match_data qca8328 = { - .id = QCA8K_ID_QCA8327, - }; - -@@ -2107,7 +2119,8 @@ static const struct qca8k_match_data qca - }; - - static const struct of_device_id qca8k_of_match[] = { -- { .compatible = "qca,qca8327", .data = &qca832x }, -+ { .compatible = "qca,qca8327", .data = &qca8327 }, -+ { .compatible = "qca,qca8328", .data = &qca8328 }, - { .compatible = "qca,qca8334", .data = &qca833x }, - { .compatible = "qca,qca8337", .data = &qca833x }, - { /* sentinel */ }, ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -260,6 +260,7 @@ struct ar8xxx_port_status { - - struct qca8k_match_data { - u8 id; -+ bool reduced_package; - }; - - enum { diff --git a/target/linux/generic/backport-5.10/797-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch b/target/linux/generic/backport-5.10/797-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch deleted file mode 100644 index 27f94dca02..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-13-net-dsa-qca8k-set-internal-delay-also-for-sgmii.patch +++ /dev/null @@ -1,159 +0,0 @@ -From cef08115846e581f80ff99abf7bf218da1840616 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:18 +0200 -Subject: net: dsa: qca8k: set internal delay also for sgmii - -QCA original code report port instability and sa that SGMII also require -to set internal delay. Generalize the rgmii delay function and apply the -advised value if they are not defined in DT. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 88 +++++++++++++++++++++++++++++++++---------------- - drivers/net/dsa/qca8k.h | 2 ++ - 2 files changed, 62 insertions(+), 28 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1004,6 +1004,7 @@ qca8k_parse_port_config(struct qca8k_pri - case PHY_INTERFACE_MODE_RGMII_ID: - case PHY_INTERFACE_MODE_RGMII_TXID: - case PHY_INTERFACE_MODE_RGMII_RXID: -+ case PHY_INTERFACE_MODE_SGMII: - delay = 0; - - if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay)) -@@ -1036,8 +1037,13 @@ qca8k_parse_port_config(struct qca8k_pri - - priv->rgmii_rx_delay[cpu_port_index] = delay; - -- break; -- case PHY_INTERFACE_MODE_SGMII: -+ /* Skip sgmii parsing for rgmii* mode */ -+ if (mode == PHY_INTERFACE_MODE_RGMII || -+ mode == PHY_INTERFACE_MODE_RGMII_ID || -+ mode == PHY_INTERFACE_MODE_RGMII_TXID || -+ mode == PHY_INTERFACE_MODE_RGMII_RXID) -+ break; -+ - if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) - priv->sgmii_tx_clk_falling_edge = true; - -@@ -1261,12 +1267,53 @@ qca8k_setup(struct dsa_switch *ds) - } - - static void -+qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index, -+ u32 reg) -+{ -+ u32 delay, val = 0; -+ int ret; -+ -+ /* Delay can be declared in 3 different way. -+ * Mode to rgmii and internal-delay standard binding defined -+ * rgmii-id or rgmii-tx/rx phy mode set. -+ * The parse logic set a delay different than 0 only when one -+ * of the 3 different way is used. In all other case delay is -+ * not enabled. With ID or TX/RXID delay is enabled and set -+ * to the default and recommended value. -+ */ -+ if (priv->rgmii_tx_delay[cpu_port_index]) { -+ delay = priv->rgmii_tx_delay[cpu_port_index]; -+ -+ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | -+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; -+ } -+ -+ if (priv->rgmii_rx_delay[cpu_port_index]) { -+ delay = priv->rgmii_rx_delay[cpu_port_index]; -+ -+ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; -+ } -+ -+ /* Set RGMII delay based on the selected values */ -+ ret = qca8k_rmw(priv, reg, -+ QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK | -+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | -+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN, -+ val); -+ if (ret) -+ dev_err(priv->dev, "Failed to set internal delay for CPU port%d", -+ cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6); -+} -+ -+static void - qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode, - const struct phylink_link_state *state) - { - struct qca8k_priv *priv = ds->priv; - int cpu_port_index, ret; -- u32 reg, val, delay; -+ u32 reg, val; - - switch (port) { - case 0: /* 1st CPU port */ -@@ -1315,32 +1362,10 @@ qca8k_phylink_mac_config(struct dsa_swit - case PHY_INTERFACE_MODE_RGMII_ID: - case PHY_INTERFACE_MODE_RGMII_TXID: - case PHY_INTERFACE_MODE_RGMII_RXID: -- val = QCA8K_PORT_PAD_RGMII_EN; -- -- /* Delay can be declared in 3 different way. -- * Mode to rgmii and internal-delay standard binding defined -- * rgmii-id or rgmii-tx/rx phy mode set. -- * The parse logic set a delay different than 0 only when one -- * of the 3 different way is used. In all other case delay is -- * not enabled. With ID or TX/RXID delay is enabled and set -- * to the default and recommended value. -- */ -- if (priv->rgmii_tx_delay[cpu_port_index]) { -- delay = priv->rgmii_tx_delay[cpu_port_index]; -- -- val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | -- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; -- } -- -- if (priv->rgmii_rx_delay[cpu_port_index]) { -- delay = priv->rgmii_rx_delay[cpu_port_index]; -- -- val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | -- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; -- } -+ qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); - -- /* Set RGMII delay based on the selected values */ -- qca8k_write(priv, reg, val); -+ /* Configure rgmii delay */ -+ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); - - /* QCA8337 requires to set rgmii rx delay for all ports. - * This is enabled through PORT5_PAD_CTRL for all ports, -@@ -1411,6 +1436,13 @@ qca8k_phylink_mac_config(struct dsa_swit - QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE | - QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, - val); -+ -+ /* From original code is reported port instability as SGMII also -+ * require delay set. Apply advised values here or take them from DT. -+ */ -+ if (state->interface == PHY_INTERFACE_MODE_SGMII) -+ qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); -+ - break; - default: - dev_err(ds->dev, "xMII mode %s not supported for port %d\n", ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -39,7 +39,9 @@ - #define QCA8K_REG_PORT5_PAD_CTRL 0x008 - #define QCA8K_REG_PORT6_PAD_CTRL 0x00c - #define QCA8K_PORT_PAD_RGMII_EN BIT(26) -+#define QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK GENMASK(23, 22) - #define QCA8K_PORT_PAD_RGMII_TX_DELAY(x) ((x) << 22) -+#define QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK GENMASK(21, 20) - #define QCA8K_PORT_PAD_RGMII_RX_DELAY(x) ((x) << 20) - #define QCA8K_PORT_PAD_RGMII_TX_DELAY_EN BIT(25) - #define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24) diff --git a/target/linux/generic/backport-5.10/797-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch b/target/linux/generic/backport-5.10/797-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch deleted file mode 100644 index b991798c87..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-14-net-dsa-qca8k-move-port-config-to-dedicated-struct.patch +++ /dev/null @@ -1,124 +0,0 @@ -From fd0bb28c547f7c8affb1691128cece38f5b626a1 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:19 +0200 -Subject: net: dsa: qca8k: move port config to dedicated struct - -Move ports related config to dedicated struct to keep things organized. - -Signed-off-by: Ansuel Smith -Reviewed-by: Florian Fainelli -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 26 +++++++++++++------------- - drivers/net/dsa/qca8k.h | 10 +++++++--- - 2 files changed, 20 insertions(+), 16 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1019,7 +1019,7 @@ qca8k_parse_port_config(struct qca8k_pri - delay = 3; - } - -- priv->rgmii_tx_delay[cpu_port_index] = delay; -+ priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay; - - delay = 0; - -@@ -1035,7 +1035,7 @@ qca8k_parse_port_config(struct qca8k_pri - delay = 3; - } - -- priv->rgmii_rx_delay[cpu_port_index] = delay; -+ priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay; - - /* Skip sgmii parsing for rgmii* mode */ - if (mode == PHY_INTERFACE_MODE_RGMII || -@@ -1045,17 +1045,17 @@ qca8k_parse_port_config(struct qca8k_pri - break; - - if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) -- priv->sgmii_tx_clk_falling_edge = true; -+ priv->ports_config.sgmii_tx_clk_falling_edge = true; - - if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) -- priv->sgmii_rx_clk_falling_edge = true; -+ priv->ports_config.sgmii_rx_clk_falling_edge = true; - - if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) { -- priv->sgmii_enable_pll = true; -+ priv->ports_config.sgmii_enable_pll = true; - - if (priv->switch_id == QCA8K_ID_QCA8327) { - dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling"); -- priv->sgmii_enable_pll = false; -+ priv->ports_config.sgmii_enable_pll = false; - } - - if (priv->switch_revision < 2) -@@ -1281,15 +1281,15 @@ qca8k_mac_config_setup_internal_delay(st - * not enabled. With ID or TX/RXID delay is enabled and set - * to the default and recommended value. - */ -- if (priv->rgmii_tx_delay[cpu_port_index]) { -- delay = priv->rgmii_tx_delay[cpu_port_index]; -+ if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) { -+ delay = priv->ports_config.rgmii_tx_delay[cpu_port_index]; - - val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | - QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; - } - -- if (priv->rgmii_rx_delay[cpu_port_index]) { -- delay = priv->rgmii_rx_delay[cpu_port_index]; -+ if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) { -+ delay = priv->ports_config.rgmii_rx_delay[cpu_port_index]; - - val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | - QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; -@@ -1397,7 +1397,7 @@ qca8k_phylink_mac_config(struct dsa_swit - - val |= QCA8K_SGMII_EN_SD; - -- if (priv->sgmii_enable_pll) -+ if (priv->ports_config.sgmii_enable_pll) - val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | - QCA8K_SGMII_EN_TX; - -@@ -1425,10 +1425,10 @@ qca8k_phylink_mac_config(struct dsa_swit - val = 0; - - /* SGMII Clock phase configuration */ -- if (priv->sgmii_rx_clk_falling_edge) -+ if (priv->ports_config.sgmii_rx_clk_falling_edge) - val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE; - -- if (priv->sgmii_tx_clk_falling_edge) -+ if (priv->ports_config.sgmii_tx_clk_falling_edge) - val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE; - - if (val) ---- a/drivers/net/dsa/qca8k.h -+++ b/drivers/net/dsa/qca8k.h -@@ -270,15 +270,19 @@ enum { - QCA8K_CPU_PORT6, - }; - --struct qca8k_priv { -- u8 switch_id; -- u8 switch_revision; -+struct qca8k_ports_config { - bool sgmii_rx_clk_falling_edge; - bool sgmii_tx_clk_falling_edge; - bool sgmii_enable_pll; - u8 rgmii_rx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ - u8 rgmii_tx_delay[QCA8K_NUM_CPU_PORTS]; /* 0: CPU port0, 1: CPU port6 */ -+}; -+ -+struct qca8k_priv { -+ u8 switch_id; -+ u8 switch_revision; - bool legacy_phy_port_mapping; -+ struct qca8k_ports_config ports_config; - struct regmap *regmap; - struct mii_bus *bus; - struct ar8xxx_port_status port_sts[QCA8K_NUM_PORTS]; diff --git a/target/linux/generic/backport-5.10/797-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch b/target/linux/generic/backport-5.10/797-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch deleted file mode 100644 index f7cb514176..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-15-dt-bindings-net-ipq8064-mdio-fix-warning-with-new-qc.patch +++ /dev/null @@ -1,26 +0,0 @@ -From e52073a8e3086046a098b8a7cbeb282ff0cdb424 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Thu, 14 Oct 2021 00:39:20 +0200 -Subject: dt-bindings: net: ipq8064-mdio: fix warning with new qca8k switch - -Fix warning now that we have qca8k switch Documentation using yaml. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml | 5 ++++- - 1 file changed, 4 insertions(+), 1 deletion(-) - ---- a/Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml -+++ b/Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.yaml -@@ -51,6 +51,9 @@ examples: - switch@10 { - compatible = "qca,qca8337"; - reg = <0x10>; -- /* ... */ -+ -+ ports { -+ /* ... */ -+ }; - }; - }; diff --git a/target/linux/generic/backport-5.10/797-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch b/target/linux/generic/backport-5.10/797-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch deleted file mode 100644 index b9bce97dd3..0000000000 --- a/target/linux/generic/backport-5.10/797-v5.16-16-dt-bindings-net-dsa-qca8k-convert-to-YAML-schema.patch +++ /dev/null @@ -1,631 +0,0 @@ -From d291fbb8245d5ba04979fed85575860a5cea7196 Mon Sep 17 00:00:00 2001 -From: Matthew Hagan -Date: Thu, 14 Oct 2021 00:39:21 +0200 -Subject: dt-bindings: net: dsa: qca8k: convert to YAML schema - -Convert the qca8k bindings to YAML format. - -Signed-off-by: Matthew Hagan -Co-developed-by: Ansuel Smith -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - .../devicetree/bindings/net/dsa/qca8k.txt | 245 -------------- - .../devicetree/bindings/net/dsa/qca8k.yaml | 362 +++++++++++++++++++++ - 2 files changed, 362 insertions(+), 245 deletions(-) - delete mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.txt - create mode 100644 Documentation/devicetree/bindings/net/dsa/qca8k.yaml - ---- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt -+++ /dev/null -@@ -1,245 +0,0 @@ --* Qualcomm Atheros QCA8xxx switch family -- --Required properties: -- --- compatible: should be one of: -- "qca,qca8328": referenced as AR8328(N)-AK1(A/B) QFN 176 pin package -- "qca,qca8327": referenced as AR8327(N)-AL1A DR-QFN 148 pin package -- "qca,qca8334": referenced as QCA8334-AL3C QFN 88 pin package -- "qca,qca8337": referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package -- --- #size-cells: must be 0 --- #address-cells: must be 1 -- --Optional properties: -- --- reset-gpios: GPIO to be used to reset the whole device --- qca,ignore-power-on-sel: Ignore power on pin strapping to configure led open -- drain or eeprom presence. This is needed for broken -- devices that have wrong configuration or when the oem -- decided to not use pin strapping and fallback to sw -- regs. --- qca,led-open-drain: Set leds to open-drain mode. This requires the -- qca,ignore-power-on-sel to be set or the driver will fail -- to probe. This is needed if the oem doesn't use pin -- strapping to set this mode and prefers to set it using sw -- regs. The pin strapping related to led open drain mode is -- the pin B68 for QCA832x and B49 for QCA833x -- --Subnodes: -- --The integrated switch subnode should be specified according to the binding --described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external --mdio-bus each subnode describing a port needs to have a valid phandle --referencing the internal PHY it is connected to. This is because there's no --N:N mapping of port and PHY id. --To declare the internal mdio-bus configuration, declare a mdio node in the --switch node and declare the phandle for the port referencing the internal --PHY is connected to. In this config a internal mdio-bus is registered and --the mdio MASTER is used as communication. -- --Don't use mixed external and internal mdio-bus configurations, as this is --not supported by the hardware. -- --This switch support 2 CPU port. Normally and advised configuration is with --CPU port set to port 0. It is also possible to set the CPU port to port 6 --if the device requires it. The driver will configure the switch to the defined --port. With both CPU port declared the first CPU port is selected as primary --and the secondary CPU ignored. -- --A CPU port node has the following optional node: -- --- fixed-link : Fixed-link subnode describing a link to a non-MDIO -- managed entity. See -- Documentation/devicetree/bindings/net/fixed-link.txt -- for details. --- qca,sgmii-rxclk-falling-edge: Set the receive clock phase to falling edge. -- Mostly used in qca8327 with CPU port 0 set to -- sgmii. --- qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge. --- qca,sgmii-enable-pll : For SGMII CPU port, explicitly enable PLL, TX and RX -- chain along with Signal Detection. -- This should NOT be enabled for qca8327. If enabled with -- qca8327 the sgmii port won't correctly init and an err -- is printed. -- This can be required for qca8337 switch with revision 2. -- A warning is displayed when used with revision greater -- 2. -- With CPU port set to sgmii and qca8337 it is advised -- to set this unless a communication problem is observed. -- --For QCA8K the 'fixed-link' sub-node supports only the following properties: -- --- 'speed' (integer, mandatory), to indicate the link speed. Accepted -- values are 10, 100 and 1000 --- 'full-duplex' (boolean, optional), to indicate that full duplex is -- used. When absent, half duplex is assumed. -- --Examples: -- --for the external mdio-bus configuration: -- -- &mdio0 { -- phy_port1: phy@0 { -- reg = <0>; -- }; -- -- phy_port2: phy@1 { -- reg = <1>; -- }; -- -- phy_port3: phy@2 { -- reg = <2>; -- }; -- -- phy_port4: phy@3 { -- reg = <3>; -- }; -- -- phy_port5: phy@4 { -- reg = <4>; -- }; -- -- switch@10 { -- compatible = "qca,qca8337"; -- #address-cells = <1>; -- #size-cells = <0>; -- -- reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; -- reg = <0x10>; -- -- ports { -- #address-cells = <1>; -- #size-cells = <0>; -- port@0 { -- reg = <0>; -- label = "cpu"; -- ethernet = <&gmac1>; -- phy-mode = "rgmii"; -- fixed-link { -- speed = 1000; -- full-duplex; -- }; -- }; -- -- port@1 { -- reg = <1>; -- label = "lan1"; -- phy-handle = <&phy_port1>; -- }; -- -- port@2 { -- reg = <2>; -- label = "lan2"; -- phy-handle = <&phy_port2>; -- }; -- -- port@3 { -- reg = <3>; -- label = "lan3"; -- phy-handle = <&phy_port3>; -- }; -- -- port@4 { -- reg = <4>; -- label = "lan4"; -- phy-handle = <&phy_port4>; -- }; -- -- port@5 { -- reg = <5>; -- label = "wan"; -- phy-handle = <&phy_port5>; -- }; -- }; -- }; -- }; -- --for the internal master mdio-bus configuration: -- -- &mdio0 { -- switch@10 { -- compatible = "qca,qca8337"; -- #address-cells = <1>; -- #size-cells = <0>; -- -- reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; -- reg = <0x10>; -- -- ports { -- #address-cells = <1>; -- #size-cells = <0>; -- -- port@0 { -- reg = <0>; -- label = "cpu"; -- ethernet = <&gmac1>; -- phy-mode = "rgmii"; -- fixed-link { -- speed = 1000; -- full-duplex; -- }; -- }; -- -- port@1 { -- reg = <1>; -- label = "lan1"; -- phy-mode = "internal"; -- phy-handle = <&phy_port1>; -- }; -- -- port@2 { -- reg = <2>; -- label = "lan2"; -- phy-mode = "internal"; -- phy-handle = <&phy_port2>; -- }; -- -- port@3 { -- reg = <3>; -- label = "lan3"; -- phy-mode = "internal"; -- phy-handle = <&phy_port3>; -- }; -- -- port@4 { -- reg = <4>; -- label = "lan4"; -- phy-mode = "internal"; -- phy-handle = <&phy_port4>; -- }; -- -- port@5 { -- reg = <5>; -- label = "wan"; -- phy-mode = "internal"; -- phy-handle = <&phy_port5>; -- }; -- }; -- -- mdio { -- #address-cells = <1>; -- #size-cells = <0>; -- -- phy_port1: phy@0 { -- reg = <0>; -- }; -- -- phy_port2: phy@1 { -- reg = <1>; -- }; -- -- phy_port3: phy@2 { -- reg = <2>; -- }; -- -- phy_port4: phy@3 { -- reg = <3>; -- }; -- -- phy_port5: phy@4 { -- reg = <4>; -- }; -- }; -- }; -- }; ---- /dev/null -+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml -@@ -0,0 +1,362 @@ -+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -+%YAML 1.2 -+--- -+$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# -+$schema: http://devicetree.org/meta-schemas/core.yaml# -+ -+title: Qualcomm Atheros QCA83xx switch family -+ -+maintainers: -+ - John Crispin -+ -+description: -+ If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode -+ describing a port needs to have a valid phandle referencing the internal PHY -+ it is connected to. This is because there is no N:N mapping of port and PHY -+ ID. To declare the internal mdio-bus configuration, declare an MDIO node in -+ the switch node and declare the phandle for the port, referencing the internal -+ PHY it is connected to. In this config, an internal mdio-bus is registered and -+ the MDIO master is used for communication. Mixed external and internal -+ mdio-bus configurations are not supported by the hardware. -+ -+properties: -+ compatible: -+ oneOf: -+ - enum: -+ - qca,qca8327 -+ - qca,qca8328 -+ - qca,qca8334 -+ - qca,qca8337 -+ description: | -+ qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package -+ qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package -+ qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package -+ qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package -+ -+ reg: -+ maxItems: 1 -+ -+ reset-gpios: -+ description: -+ GPIO to be used to reset the whole device -+ maxItems: 1 -+ -+ qca,ignore-power-on-sel: -+ $ref: /schemas/types.yaml#/definitions/flag -+ description: -+ Ignore power-on pin strapping to configure LED open-drain or EEPROM -+ presence. This is needed for devices with incorrect configuration or when -+ the OEM has decided not to use pin strapping and falls back to SW regs. -+ -+ qca,led-open-drain: -+ $ref: /schemas/types.yaml#/definitions/flag -+ description: -+ Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to -+ be set, otherwise the driver will fail at probe. This is required if the -+ OEM does not use pin strapping to set this mode and prefers to set it -+ using SW regs. The pin strappings related to LED open-drain mode are -+ B68 on the QCA832x and B49 on the QCA833x. -+ -+ mdio: -+ type: object -+ description: Qca8k switch have an internal mdio to access switch port. -+ If this is not present, the legacy mapping is used and the -+ internal mdio access is used. -+ With the legacy mapping the reg corresponding to the internal -+ mdio is the switch reg with an offset of -1. -+ -+ properties: -+ '#address-cells': -+ const: 1 -+ '#size-cells': -+ const: 0 -+ -+ patternProperties: -+ "^(ethernet-)?phy@[0-4]$": -+ type: object -+ -+ allOf: -+ - $ref: "http://devicetree.org/schemas/net/mdio.yaml#" -+ -+ properties: -+ reg: -+ maxItems: 1 -+ -+ required: -+ - reg -+ -+patternProperties: -+ "^(ethernet-)?ports$": -+ type: object -+ properties: -+ '#address-cells': -+ const: 1 -+ '#size-cells': -+ const: 0 -+ -+ patternProperties: -+ "^(ethernet-)?port@[0-6]$": -+ type: object -+ description: Ethernet switch ports -+ -+ properties: -+ reg: -+ description: Port number -+ -+ label: -+ description: -+ Describes the label associated with this port, which will become -+ the netdev name -+ $ref: /schemas/types.yaml#/definitions/string -+ -+ link: -+ description: -+ Should be a list of phandles to other switch's DSA port. This -+ port is used as the outgoing port towards the phandle ports. The -+ full routing information must be given, not just the one hop -+ routes to neighbouring switches -+ $ref: /schemas/types.yaml#/definitions/phandle-array -+ -+ ethernet: -+ description: -+ Should be a phandle to a valid Ethernet device node. This host -+ device is what the switch port is connected to -+ $ref: /schemas/types.yaml#/definitions/phandle -+ -+ phy-handle: true -+ -+ phy-mode: true -+ -+ fixed-link: true -+ -+ mac-address: true -+ -+ sfp: true -+ -+ qca,sgmii-rxclk-falling-edge: -+ $ref: /schemas/types.yaml#/definitions/flag -+ description: -+ Set the receive clock phase to falling edge. Mostly commonly used on -+ the QCA8327 with CPU port 0 set to SGMII. -+ -+ qca,sgmii-txclk-falling-edge: -+ $ref: /schemas/types.yaml#/definitions/flag -+ description: -+ Set the transmit clock phase to falling edge. -+ -+ qca,sgmii-enable-pll: -+ $ref: /schemas/types.yaml#/definitions/flag -+ description: -+ For SGMII CPU port, explicitly enable PLL, TX and RX chain along with -+ Signal Detection. On the QCA8327 this should not be enabled, otherwise -+ the SGMII port will not initialize. When used on the QCA8337, revision 3 -+ or greater, a warning will be displayed. When the CPU port is set to -+ SGMII on the QCA8337, it is advised to set this unless a communication -+ issue is observed. -+ -+ required: -+ - reg -+ -+ additionalProperties: false -+ -+oneOf: -+ - required: -+ - ports -+ - required: -+ - ethernet-ports -+ -+required: -+ - compatible -+ - reg -+ -+additionalProperties: true -+ -+examples: -+ - | -+ #include -+ -+ mdio { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ external_phy_port1: ethernet-phy@0 { -+ reg = <0>; -+ }; -+ -+ external_phy_port2: ethernet-phy@1 { -+ reg = <1>; -+ }; -+ -+ external_phy_port3: ethernet-phy@2 { -+ reg = <2>; -+ }; -+ -+ external_phy_port4: ethernet-phy@3 { -+ reg = <3>; -+ }; -+ -+ external_phy_port5: ethernet-phy@4 { -+ reg = <4>; -+ }; -+ -+ switch@10 { -+ compatible = "qca,qca8337"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; -+ reg = <0x10>; -+ -+ ports { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ port@0 { -+ reg = <0>; -+ label = "cpu"; -+ ethernet = <&gmac1>; -+ phy-mode = "rgmii"; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "lan1"; -+ phy-handle = <&external_phy_port1>; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "lan2"; -+ phy-handle = <&external_phy_port2>; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "lan3"; -+ phy-handle = <&external_phy_port3>; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "lan4"; -+ phy-handle = <&external_phy_port4>; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "wan"; -+ phy-handle = <&external_phy_port5>; -+ }; -+ }; -+ }; -+ }; -+ - | -+ #include -+ -+ mdio { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ switch@10 { -+ compatible = "qca,qca8337"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; -+ reg = <0x10>; -+ -+ ports { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ port@0 { -+ reg = <0>; -+ label = "cpu"; -+ ethernet = <&gmac1>; -+ phy-mode = "rgmii"; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "lan1"; -+ phy-mode = "internal"; -+ phy-handle = <&internal_phy_port1>; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "lan2"; -+ phy-mode = "internal"; -+ phy-handle = <&internal_phy_port2>; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "lan3"; -+ phy-mode = "internal"; -+ phy-handle = <&internal_phy_port3>; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "lan4"; -+ phy-mode = "internal"; -+ phy-handle = <&internal_phy_port4>; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "wan"; -+ phy-mode = "internal"; -+ phy-handle = <&internal_phy_port5>; -+ }; -+ -+ port@6 { -+ reg = <0>; -+ label = "cpu"; -+ ethernet = <&gmac1>; -+ phy-mode = "sgmii"; -+ -+ qca,sgmii-rxclk-falling-edge; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ }; -+ -+ mdio { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ internal_phy_port1: ethernet-phy@0 { -+ reg = <0>; -+ }; -+ -+ internal_phy_port2: ethernet-phy@1 { -+ reg = <1>; -+ }; -+ -+ internal_phy_port3: ethernet-phy@2 { -+ reg = <2>; -+ }; -+ -+ internal_phy_port4: ethernet-phy@3 { -+ reg = <3>; -+ }; -+ -+ internal_phy_port5: ethernet-phy@4 { -+ reg = <4>; -+ }; -+ }; -+ }; -+ }; diff --git a/target/linux/generic/backport-5.10/798-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch b/target/linux/generic/backport-5.10/798-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch deleted file mode 100644 index a510cfdc18..0000000000 --- a/target/linux/generic/backport-5.10/798-v5.16-net-dsa-qca8k-fix-delay-applied-to-wrong-cpu-in-parse-p.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 06dd34a628ae5b6a839b757e746de165d6789ca8 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Sun, 17 Oct 2021 16:56:46 +0200 -Subject: net: dsa: qca8k: fix delay applied to wrong cpu in parse_port_config - -Fix delay settings applied to wrong cpu in parse_port_config. The delay -values is set to the wrong index as the cpu_port_index is incremented -too early. Start the cpu_port_index to -1 so the correct value is -applied to address also the case with invalid phy mode and not available -port. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -976,7 +976,7 @@ qca8k_setup_of_pws_reg(struct qca8k_priv - static int - qca8k_parse_port_config(struct qca8k_priv *priv) - { -- int port, cpu_port_index = 0, ret; -+ int port, cpu_port_index = -1, ret; - struct device_node *port_dn; - phy_interface_t mode; - struct dsa_port *dp; diff --git a/target/linux/generic/backport-5.10/799-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch b/target/linux/generic/backport-5.10/799-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch deleted file mode 100644 index 71fa3022d5..0000000000 --- a/target/linux/generic/backport-5.10/799-v5.16-net-dsa-qca8k-tidy-for-loop-in-setup-and-add-cpu-port-c.patch +++ /dev/null @@ -1,151 +0,0 @@ -From 040e926f5813a5f4cc18dbff7c942d1e52f368f2 Mon Sep 17 00:00:00 2001 -From: Ansuel Smith -Date: Tue, 19 Oct 2021 02:08:50 +0200 -Subject: net: dsa: qca8k: tidy for loop in setup and add cpu port check - -Tidy and organize qca8k setup function from multiple for loop. -Change for loop in bridge leave/join to scan all port and skip cpu port. -No functional change intended. - -Signed-off-by: Ansuel Smith -Signed-off-by: David S. Miller ---- - drivers/net/dsa/qca8k.c | 74 +++++++++++++++++++++++++++++-------------------- - 1 file changed, 44 insertions(+), 30 deletions(-) - ---- a/drivers/net/dsa/qca8k.c -+++ b/drivers/net/dsa/qca8k.c -@@ -1122,28 +1122,34 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - dev_warn(priv->dev, "mib init failed"); - -- /* Enable QCA header mode on the cpu port */ -- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(cpu_port), -- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | -- QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); -- if (ret) { -- dev_err(priv->dev, "failed enabling QCA header mode"); -- return ret; -- } -- -- /* Disable forwarding by default on all ports */ -+ /* Initial setup of all ports */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ /* Disable forwarding by default on all ports */ - ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), - QCA8K_PORT_LOOKUP_MEMBER, 0); - if (ret) - return ret; -- } - -- /* Disable MAC by default on all ports */ -- for (i = 1; i < QCA8K_NUM_PORTS; i++) -- qca8k_port_set_status(priv, i, 0); -+ /* Enable QCA header mode on all cpu ports */ -+ if (dsa_is_cpu_port(ds, i)) { -+ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i), -+ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S | -+ QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S); -+ if (ret) { -+ dev_err(priv->dev, "failed enabling QCA header mode"); -+ return ret; -+ } -+ } -+ -+ /* Disable MAC by default on all user ports */ -+ if (dsa_is_user_port(ds, i)) -+ qca8k_port_set_status(priv, i, 0); -+ } - -- /* Forward all unknown frames to CPU port for Linux processing */ -+ /* Forward all unknown frames to CPU port for Linux processing -+ * Notice that in multi-cpu config only one port should be set -+ * for igmp, unknown, multicast and broadcast packet -+ */ - ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, - BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S | - BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S | -@@ -1152,11 +1158,13 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - -- /* Setup connection between CPU port & user ports */ -+ /* Setup connection between CPU port & user ports -+ * Configure specific switch configuration for ports -+ */ - for (i = 0; i < QCA8K_NUM_PORTS; i++) { - /* CPU port gets connected to all user ports of the switch */ - if (dsa_is_cpu_port(ds, i)) { -- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port), -+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), - QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); - if (ret) - return ret; -@@ -1193,16 +1201,14 @@ qca8k_setup(struct dsa_switch *ds) - if (ret) - return ret; - } -- } - -- /* The port 5 of the qca8337 have some problem in flood condition. The -- * original legacy driver had some specific buffer and priority settings -- * for the different port suggested by the QCA switch team. Add this -- * missing settings to improve switch stability under load condition. -- * This problem is limited to qca8337 and other qca8k switch are not affected. -- */ -- if (priv->switch_id == QCA8K_ID_QCA8337) { -- for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ /* The port 5 of the qca8337 have some problem in flood condition. The -+ * original legacy driver had some specific buffer and priority settings -+ * for the different port suggested by the QCA switch team. Add this -+ * missing settings to improve switch stability under load condition. -+ * This problem is limited to qca8337 and other qca8k switch are not affected. -+ */ -+ if (priv->switch_id == QCA8K_ID_QCA8337) { - switch (i) { - /* The 2 CPU port and port 5 requires some different - * priority than any other ports. -@@ -1238,6 +1244,12 @@ qca8k_setup(struct dsa_switch *ds) - QCA8K_PORT_HOL_CTRL1_WRED_EN, - mask); - } -+ -+ /* Set initial MTU for every port. -+ * We have only have a general MTU setting. So track -+ * every port and set the max across all port. -+ */ -+ priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; - } - - /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ -@@ -1251,8 +1263,6 @@ qca8k_setup(struct dsa_switch *ds) - } - - /* Setup our port MTUs to match power on defaults */ -- for (i = 0; i < QCA8K_NUM_PORTS; i++) -- priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN; - ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); - if (ret) - dev_warn(priv->dev, "failed setting MTU settings"); -@@ -1728,7 +1738,9 @@ qca8k_port_bridge_join(struct dsa_switch - cpu_port = dsa_to_port(ds, port)->cpu_dp->index; - port_mask = BIT(cpu_port); - -- for (i = 1; i < QCA8K_NUM_PORTS; i++) { -+ for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ if (dsa_is_cpu_port(ds, i)) -+ continue; - if (dsa_to_port(ds, i)->bridge_dev != br) - continue; - /* Add this port to the portvlan mask of the other ports -@@ -1758,7 +1770,9 @@ qca8k_port_bridge_leave(struct dsa_switc - - cpu_port = dsa_to_port(ds, port)->cpu_dp->index; - -- for (i = 1; i < QCA8K_NUM_PORTS; i++) { -+ for (i = 0; i < QCA8K_NUM_PORTS; i++) { -+ if (dsa_is_cpu_port(ds, i)) -+ continue; - if (dsa_to_port(ds, i)->bridge_dev != br) - continue; - /* Remove this port to the portvlan mask of the other ports