From: Thibaut VARÈNE Date: Thu, 14 Apr 2022 10:39:03 +0000 (+0200) Subject: ath79: add support for Yuncore XD3200 X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fstaging%2Fmkresin.git;a=commitdiff_plain;h=c91df224f54fdd44c9c0487a8c91876f5d273164 ath79: add support for Yuncore XD3200 Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 230f2fe417..ace5cab30f 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -69,6 +69,7 @@ samsung,wam250|\ ubnt,nanostation-m|\ yuncore,a770|\ yuncore,a782|\ +yuncore,xd3200|\ yuncore,xd4200|\ ziking,cpe46b|\ zyxel,nbg6616) diff --git a/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts b/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts new file mode 100644 index 0000000000..5c87752585 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_yuncore_xd4200.dtsi" + +/ { + compatible = "yuncore,xd3200", "qca,qca9563"; + model = "YunCore XD3200"; + + aliases { + label-mac-device = ð0; + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "green:system"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan2g { + label = "blue:wlan2g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index e22cee51a3..12a54f3bd5 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -246,7 +246,8 @@ glinet,gl-x750) hak5,lan-turtle) ucidef_set_led_netdev "wan" "WAN" "orange:system" "eth1" ;; -joyit,jt-or750i) +joyit,jt-or750i|\ +yuncore,xd3200) ucidef_set_led_default "ath10k" "ath10k-disable" "ath10k-phy0" "0" ;; meraki,mr12|\ diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 2f0208b288..03e6434422 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -365,6 +365,7 @@ ath79_setup_interfaces() ubnt,nanobeam-ac-gen2|\ ubnt,nanostation-ac|\ yuncore,a782|\ + yuncore,xd3200|\ yuncore,xd4200) ucidef_add_switch "switch0" \ "0@eth0" "2:lan" "3:wan" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 348b8839b6..17121d9618 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -46,7 +46,8 @@ case "$FIRMWARE" in ubnt,powerbeam-5ac-gen2|\ ubnt,rocket-5ac-lite|\ ubnt,unifiac-pro|\ - yuncore,a770) + yuncore,a770|\ + yuncore,xd3200) caldata_extract "art" 0x5000 0x844 ;; avm,fritz1750e|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 769c0ee1da..33a72358b3 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -2528,6 +2528,17 @@ define Device/yuncore_a782 endef TARGET_DEVICES += yuncore_a782 +define Device/yuncore_xd3200 + SOC := qca9563 + DEVICE_VENDOR := YunCore + DEVICE_MODEL := XD3200 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct + IMAGE_SIZE := 16000k + IMAGES += tftp.bin + IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m +endef +TARGET_DEVICES += yuncore_xd3200 + define Device/yuncore_xd4200 SOC := qca9563 DEVICE_VENDOR := YunCore