From 765f66810a3324cc35fa6471ee8eeee335ba8c2b Mon Sep 17 00:00:00 2001 From: David Bauer Date: Sat, 18 Mar 2023 02:28:23 +0100 Subject: [PATCH] mpc85xx: add support for Enterasys WS-AP3715i Hardware -------- SoC: NXP P1010 (1x e500 @ 800MHz) RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9) FLASH: 32M NOR (Spansion S25FL256S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035) UART: 115200 8N1 (RJ-45 Cisco) Installation ------------ 1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in the root directory of a TFTP server and serve it at 192.168.1.66/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Alter the bootcmd in U-Boot: $ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm" $ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000; bootm 0x2000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Boot the initramfs image $ run ramboot_openwrt 5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install using sysupgrade. $ sysupgrade -n Signed-off-by: David Bauer --- package/boot/uboot-envtools/files/mpc85xx | 4 + .../mpc85xx/base-files/etc/board.d/01_leds | 1 + .../mpc85xx/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/ieee80211/10-fix-wifi-mac | 4 + .../base-files/lib/preinit/10_fix_eth_mac.sh | 1 + target/linux/mpc85xx/config-5.15 | 1 + .../arch/powerpc/boot/dts/ws-ap3715i.dts | 293 ++++++++++++++++++ .../arch/powerpc/platforms/85xx/ws-ap3715i.c | 87 ++++++ target/linux/mpc85xx/image/p1010.mk | 13 + target/linux/mpc85xx/p1010/config-default | 4 + target/linux/mpc85xx/p1010/target.mk | 2 +- ...-powerpc-85xx-add-ws-ap3715i-support.patch | 50 +++ ...-powerpc-85xx-add-ws-ap3715i-support.patch | 50 +++ 13 files changed, 511 insertions(+), 2 deletions(-) create mode 100644 target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts create mode 100644 target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c create mode 100644 target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch create mode 100644 target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch diff --git a/package/boot/uboot-envtools/files/mpc85xx b/package/boot/uboot-envtools/files/mpc85xx index 6d389c5b57..a74466ab3a 100644 --- a/package/boot/uboot-envtools/files/mpc85xx +++ b/package/boot/uboot-envtools/files/mpc85xx @@ -8,6 +8,10 @@ touch /etc/config/ubootenv board=$(board_name) case "$board" in +enterasys,ws-ap3715i) + ubootenv_add_uci_config "$(find_mtd_part 'cfg1')" "0x0" "0x10000" "0x10000" + ubootenv_add_uci_config "$(find_mtd_part 'cfg2')" "0x0" "0x10000" "0x10000" + ;; extreme-networks,ws-ap3825i) ubootenv_add_uci_config "$(find_mtd_part 'cfg1')" "0x0" "0x10000" "0x20000" ubootenv_add_uci_config "$(find_mtd_part 'cfg2')" "0x0" "0x10000" "0x20000" diff --git a/target/linux/mpc85xx/base-files/etc/board.d/01_leds b/target/linux/mpc85xx/base-files/etc/board.d/01_leds index 391c909e4c..d9b4d2d79d 100644 --- a/target/linux/mpc85xx/base-files/etc/board.d/01_leds +++ b/target/linux/mpc85xx/base-files/etc/board.d/01_leds @@ -8,6 +8,7 @@ boardname="${board##*,}" board_config_update case $board in +enterasys,ws-ap3715i|\ extreme-networks,ws-ap3825i) ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1" ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0" diff --git a/target/linux/mpc85xx/base-files/etc/board.d/02_network b/target/linux/mpc85xx/base-files/etc/board.d/02_network index 77e208c7fa..04c27769a9 100644 --- a/target/linux/mpc85xx/base-files/etc/board.d/02_network +++ b/target/linux/mpc85xx/base-files/etc/board.d/02_network @@ -9,7 +9,8 @@ board_config_update board=$(board_name) case "$board" in -aerohive,hiveap-330) +aerohive,hiveap-330|\ +enterasys,ws-ap3715i) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; ocedo,panda) diff --git a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac index 8050c7bea2..20ad8eb44f 100644 --- a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac +++ b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac @@ -12,6 +12,10 @@ PHYNBR=${DEVPATH##*/phy} board=$(board_name) case "$board" in +enterasys,ws-ap3715i) + [ "$PHYNBR" -eq 0 ] && mtd_get_mac_ascii cfg2 RADIOADDR1 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" -eq 1 ] && mtd_get_mac_ascii cfg2 RADIOADDR0 > /sys${DEVPATH}/macaddress + ;; enterasys,ws-ap3710i|\ extreme-networks,ws-ap3825i) mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR} > /sys${DEVPATH}/macaddress diff --git a/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh index 0d9058420b..ddb9bef141 100644 --- a/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh @@ -3,6 +3,7 @@ preinit_set_mac_address() { case $(board_name) in + enterasys,ws-ap3715i|\ extreme-networks,ws-ap3825i) ip link set dev eth0 address $(mtd_get_mac_ascii cfg1 ethaddr) ip link set dev eth1 address $(mtd_get_mac_ascii cfg1 eth1addr) diff --git a/target/linux/mpc85xx/config-5.15 b/target/linux/mpc85xx/config-5.15 index ab2eef94cd..42d17c1361 100644 --- a/target/linux/mpc85xx/config-5.15 +++ b/target/linux/mpc85xx/config-5.15 @@ -262,6 +262,7 @@ CONFIG_VDSO32=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_WATCHDOG_CORE=y # CONFIG_WS_AP3710I is not set +# CONFIG_WS_AP3715I is not set # CONFIG_WS_AP3825I is not set # CONFIG_XES_MPC85xx is not set CONFIG_XZ_DEC_BCJ=y diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts new file mode 100644 index 0000000000..d13952acae --- /dev/null +++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts @@ -0,0 +1,293 @@ +// SPDX-License-Identifier: GPL-2.0-or-later or MIT + +#include + +/include/ "fsl/p1010si-pre.dtsi" + +/ { + model = "Enterasys WS-AP3715i"; + compatible = "enterasys,ws-ap3715i"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_red; + label-mac-device = &enet0; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x10000000>; + }; + + leds { + compatible = "gpio-leds"; + + wifi1 { + gpios = <&spi_gpio 3 GPIO_ACTIVE_HIGH>; + label = "green:radio1"; + linux,default-trigger = "phy1tpt"; + }; + + wifi2 { + gpios = <&spi_gpio 2 GPIO_ACTIVE_HIGH>; + label = "green:radio2"; + linux,default-trigger = "phy0tpt"; + }; + + led_power_green: power_green { + gpios = <&spi_gpio 0 GPIO_ACTIVE_HIGH>; + label = "green:power"; + }; + + led_power_red: power_red { + gpios = <&spi_gpio 1 GPIO_ACTIVE_HIGH>; + label = "red:power"; + }; + + lan1_red { + gpios = <&spi_gpio 6 GPIO_ACTIVE_HIGH>; + label = "red:lan1"; + }; + + lan1_green { + gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>; + label = "green:lan1"; + }; + + lan2_red { + gpios = <&spi_gpio 7 GPIO_ACTIVE_HIGH>; + label = "red:lan2"; + }; + + lan2_green { + gpios = <&spi_gpio 5 GPIO_ACTIVE_HIGH>; + label = "green:lan2"; + }; + }; + + soc: soc@ffe00000 { + ranges = <0x0 0x0 0xffe00000 0x100000>; + + gpio0: gpio-controller@fc00 { + }; + + usb@22000 { + status = "disabled"; + }; + + mdio@24000 { + phy0: ethernet-phy@0 { + reg = <0x1>; + }; + + phy2: ethernet-phy@2 { + reg = <0x2>; + }; + }; + + mdio@25000 { + tbi_phy: tbi-phy@11 { + reg = <0x11>; + }; + }; + + mdio@26000 { + status = "disabled"; + }; + + enet0: ethernet@b0000 { + phy-handle = <&phy0>; + phy-connection-type = "rgmii-id"; + + label = "lan1"; + }; + + enet1: ethernet@b1000 { + phy-handle = <&phy2>; + phy-connection-type = "sgmii"; + + tbi-handle = <&tbi_phy>; + + label = "lan2"; + }; + + enet2: ethernet@b2000 { + status = "disabled"; + }; + + sdhc@2e000 { + status = "disabled"; + }; + }; + + ifc: ifc@ffe1e000 { + }; + + pci0: pcie@ffe09000 { + reg = <0 0xffe09000 0 0x1000>; + ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>; + pcie@0 { + ranges = <0x2000000 0x0 0xa0000000 + 0x2000000 0x0 0xa0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + + wifi@0,0,0 { + compatible = "pci168c,0033"; + reg = <0x0 0 0 0 0>; + ieee80211-freq-limit = <2400000 2500000>; + }; + }; + }; + + pci1: pcie@ffe0a000 { + reg = <0 0xffe0a000 0 0x1000>; + ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>; + pcie@0 { + ranges = <0x2000000 0x0 0x80000000 + 0x2000000 0x0 0x80000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + + wifi@0,0,0 { + compatible = "pci168c,0033"; + reg = <0x0 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + }; + }; + }; +}; + +&soc { + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + + spi_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + spi-max-frequency = <100000>; + }; + }; + + spi0: spi@7000 { + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0xa0000>; + label = "boot-bak"; + read-only; + }; + + partition@a0000 { + reg = <0xa0000 0xa0000>; + label = "boot-pri"; + read-only; + }; + + partition@120000 { + reg = <0x120000 0x10000>; + label = "cfg1"; + read-only; + }; + + partition@130000 { + reg = <0x130000 0x10000>; + label = "cfg2"; + read-only; + }; + + partition@140000 { + compatible = "denx,uimage"; + reg = <0x140000 0x1d80000>; + label = "firmware"; + }; + + partition@1ec0000 { + reg = <0x1ec0000 0x100000>; + label = "nvram"; + read-only; + }; + }; + }; + }; +}; + +/include/ "fsl/p1010si-post.dtsi" + +/ { + cpus { + PowerPC,P1010@0 { + bus-frequency = <399999996>; + timebase-frequency = <50000000>; + clock-frequency = <799999992>; + d-cache-block-size = <0x20>; + d-cache-size = <0x8000>; + d-cache-sets = <0x80>; + i-cache-block-size = <0x20>; + i-cache-size = <0x8000>; + i-cache-sets = <0x80>; + }; + }; + + soc@ffe00000 { + bus-frequency = <399999996>; + + serial@4600 { + clock-frequency = <399999996>; + status = "disabled"; + }; + + serial@4500 { + clock-frequency = <399999996>; + }; + + pic@40000 { + clock-frequency = <399999996>; + }; + }; +}; + +/* + * For the OpenWrt 22.03 release, since Linux 5.10.138 now uses + * aliases to determine PCI domain numbers, drop aliases so as not to + * change the sysfs path of our wireless netdevs. + */ + +/ { + aliases { + /delete-property/ pci0; + /delete-property/ pci1; + }; +}; + diff --git a/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c new file mode 100644 index 0000000000..aa2a366b3d --- /dev/null +++ b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +/* + * Enterasys WS-AP3715i Board Setup + * + * Copyright (C) 2023 David Bauer + * + * Based on: + * p1010rdb.c: + * P1010 RDB Board Setup + * Copyright 2011 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#include "mpc85xx.h" + +void __init wsap3715i_pic_init(void) +{ + struct mpic *mpic; + + mpic = mpic_alloc(NULL, 0, + MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU, + 0, 256, " OpenPIC "); + + BUG_ON(mpic == NULL); + mpic_init(mpic); +} + +/* + * Setup the architecture + */ +static void __init wsap3715i_setup_arch(void) +{ + if (ppc_md.progress) + ppc_md.progress("wsap3715i_setup_arch()", 0); + + fsl_pci_assign_primary(); + + pr_info("WS-AP3715i from Enterasys\n"); +} + +machine_arch_initcall(wsap3715i, mpc85xx_common_publish_devices); + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init wsap3715i_probe(void) +{ + if (of_machine_is_compatible("enterasys,ws-ap3715i")) + return 1; + return 0; +} + +define_machine(wsap3715i) { + .name = "P1010 RDB", + .probe = wsap3715i_probe, + .setup_arch = wsap3715i_setup_arch, + .init_IRQ = wsap3715i_pic_init, +#ifdef CONFIG_PCI + .pcibios_fixup_bus = fsl_pcibios_fixup_bus, + .pcibios_fixup_phb = fsl_pcibios_fixup_phb, +#endif + .get_irq = mpic_get_irq, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, +}; diff --git a/target/linux/mpc85xx/image/p1010.mk b/target/linux/mpc85xx/image/p1010.mk index 90ef46d709..034f6abc40 100644 --- a/target/linux/mpc85xx/image/p1010.mk +++ b/target/linux/mpc85xx/image/p1010.mk @@ -14,6 +14,19 @@ define Build/spi-loader-okli mv "$@.new" "$@" endef +define Device/enterasys_ws-ap3715i + DEVICE_VENDOR := Enterasys + DEVICE_MODEL := WS-AP3715i + BLOCKSIZE := 64k + KERNEL_NAME := simpleImage.ws-ap3715i + KERNEL_ENTRY := 0x1000000 + KERNEL_LOADADDR := 0x1000000 + KERNEL = kernel-bin | lzma | uImage lzma + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata +endef +TARGET_DEVICES += enterasys_ws-ap3715i + define Device/tplink_tl-wdr4900-v1 DEVICE_VENDOR := TP-Link DEVICE_MODEL := TL-WDR4900 diff --git a/target/linux/mpc85xx/p1010/config-default b/target/linux/mpc85xx/p1010/config-default index 53e077b6c2..6af6b8e097 100644 --- a/target/linux/mpc85xx/p1010/config-default +++ b/target/linux/mpc85xx/p1010/config-default @@ -1,9 +1,11 @@ CONFIG_AT803X_PHY=y CONFIG_CMDLINE_OVERRIDE=y # CONFIG_FSL_CORENET_CF is not set +CONFIG_GPIO_74X164=y CONFIG_MTD_NAND_FSL_IFC=y CONFIG_MTD_SPLIT_FIRMWARE=y CONFIG_MTD_SPLIT_TPLINK_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_MTD_UBI=y CONFIG_MTD_UBI_BEB_LIMIT=20 CONFIG_MTD_UBI_BLOCK=y @@ -18,6 +20,8 @@ CONFIG_REALTEK_PHY=y CONFIG_RED_15W_REV1=y CONFIG_REGMAP=y CONFIG_REGULATOR=y +CONFIG_SPI_GPIO=y CONFIG_TL_WDR4900_V1=y CONFIG_UBIFS_FS=y +CONFIG_WS_AP3715I=y CONFIG_FIREBOX_T10=y \ No newline at end of file diff --git a/target/linux/mpc85xx/p1010/target.mk b/target/linux/mpc85xx/p1010/target.mk index 86628e32da..fa1bb7542d 100644 --- a/target/linux/mpc85xx/p1010/target.mk +++ b/target/linux/mpc85xx/p1010/target.mk @@ -1,5 +1,5 @@ BOARDNAME:=P1010 -KERNEL_IMAGES:=simpleImage.tl-wdr4900-v1 +KERNEL_IMAGES:=simpleImage.tl-wdr4900-v1 simpleImage.ws-ap3715i define Target/Description Build firmware images for P1010 based boards. diff --git a/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch b/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch new file mode 100644 index 0000000000..10ba744897 --- /dev/null +++ b/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch @@ -0,0 +1,50 @@ +--- a/arch/powerpc/platforms/85xx/Kconfig ++++ b/arch/powerpc/platforms/85xx/Kconfig +@@ -82,6 +82,17 @@ config WS_AP3710I + This board is a Concurrent Dual-Band wireless access point with a + Freescale P1020 SoC. + ++config WS_AP3715I ++ bool "Enterasys WS-AP3715i" ++ select DEFAULT_UIMAGE ++ select ARCH_REQUIRE_GPIOLIB ++ select GPIO_MPC8XXX ++ help ++ This option enables support for the Enterasys WS-AP3715i board. ++ ++ This board is a Concurrent Dual-Band wireless access point with a ++ Freescale P1010 SoC. ++ + config WS_AP3825I + bool "Extreme Networks WS-AP3825i" + select DEFAULT_UIMAGE +--- a/arch/powerpc/platforms/85xx/Makefile ++++ b/arch/powerpc/platforms/85xx/Makefile +@@ -27,6 +27,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o + obj-$(CONFIG_PANDA) += panda.o + obj-$(CONFIG_TWR_P102x) += twr_p102x.o + obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o ++obj-$(CONFIG_WS_AP3715I) += ws-ap3715i.o + obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o + obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o + obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o +--- a/arch/powerpc/boot/Makefile ++++ b/arch/powerpc/boot/Makefile +@@ -340,6 +340,7 @@ image-$(CONFIG_TQM8560) += cuImage.tqm + image-$(CONFIG_SBC8548) += cuImage.sbc8548 + image-$(CONFIG_KSI8560) += cuImage.ksi8560 + image-$(CONFIG_TL_WDR4900_V1) += simpleImage.tl-wdr4900-v1 ++image-$(CONFIG_WS_AP3715I) += simpleImage.ws-ap3715i + image-$(CONFIG_WS_AP3825I) += simpleImage.ws-ap3825i + # Board ports in arch/powerpc/platform/86xx/Kconfig + image-$(CONFIG_MVME7100) += dtbImage.mvme7100 +--- a/arch/powerpc/boot/wrapper ++++ b/arch/powerpc/boot/wrapper +@@ -324,6 +324,7 @@ adder875-redboot) + platformo="$object/fixed-head.o $object/redboot-8xx.o" + binary=y + ;; ++simpleboot-ws-ap3715i|\ + simpleboot-ws-ap3825i|\ + simpleboot-tl-wdr4900-v1) + platformo="$object/fixed-head.o $object/simpleboot.o" diff --git a/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch b/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch new file mode 100644 index 0000000000..8272d9dd2a --- /dev/null +++ b/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch @@ -0,0 +1,50 @@ +--- a/arch/powerpc/platforms/85xx/Kconfig ++++ b/arch/powerpc/platforms/85xx/Kconfig +@@ -82,6 +82,17 @@ config WS_AP3710I + This board is a Concurrent Dual-Band wireless access point with a + Freescale P1020 SoC. + ++config WS_AP3715I ++ bool "Enterasys WS-AP3715i" ++ select DEFAULT_UIMAGE ++ select ARCH_REQUIRE_GPIOLIB ++ select GPIO_MPC8XXX ++ help ++ This option enables support for the Enterasys WS-AP3715i board. ++ ++ This board is a Concurrent Dual-Band wireless access point with a ++ Freescale P1010 SoC. ++ + config WS_AP3825I + bool "Extreme Networks WS-AP3825i" + select DEFAULT_UIMAGE +--- a/arch/powerpc/platforms/85xx/Makefile ++++ b/arch/powerpc/platforms/85xx/Makefile +@@ -27,6 +27,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o + obj-$(CONFIG_PANDA) += panda.o + obj-$(CONFIG_TWR_P102x) += twr_p102x.o + obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o ++obj-$(CONFIG_WS_AP3715I) += ws-ap3715i.o + obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o + obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o + obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o +--- a/arch/powerpc/boot/Makefile ++++ b/arch/powerpc/boot/Makefile +@@ -346,6 +346,7 @@ image-$(CONFIG_TQM8555) += cuImage.tqm + image-$(CONFIG_TQM8560) += cuImage.tqm8560 + image-$(CONFIG_KSI8560) += cuImage.ksi8560 + image-$(CONFIG_TL_WDR4900_V1) += simpleImage.tl-wdr4900-v1 ++image-$(CONFIG_WS_AP3715I) += simpleImage.ws-ap3715i + image-$(CONFIG_WS_AP3825I) += simpleImage.ws-ap3825i + # Board ports in arch/powerpc/platform/86xx/Kconfig + image-$(CONFIG_MVME7100) += dtbImage.mvme7100 +--- a/arch/powerpc/boot/wrapper ++++ b/arch/powerpc/boot/wrapper +@@ -326,6 +326,7 @@ adder875-redboot) + platformo="$object/fixed-head.o $object/redboot-8xx.o" + binary=y + ;; ++simpleboot-ws-ap3715i|\ + simpleboot-ws-ap3825i|\ + simpleboot-tl-wdr4900-v1) + platformo="$object/fixed-head.o $object/simpleboot.o" -- 2.30.2