From 4e31b2e8697c21f9bd6493bb3d78a4a41c6a9a52 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Sat, 12 Dec 2015 07:38:06 +0000 Subject: [PATCH] ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov SVN-Revision: 47881 --- .../ramips/base-files/etc/board.d/02_network | 1 + target/linux/ramips/base-files/lib/ramips.sh | 5 +- .../ramips/base-files/lib/upgrade/platform.sh | 24 ++++ .../ramips/base-files/lib/upgrade/ubnt.sh | 76 +++++++++++ target/linux/ramips/dts/UBNT-ERX.dts | 119 ++++++++++++++++++ target/linux/ramips/image/Makefile | 61 ++++++++- target/linux/ramips/mt7621/profiles/ubnt.mk | 17 +++ 7 files changed, 301 insertions(+), 2 deletions(-) create mode 100644 target/linux/ramips/base-files/lib/upgrade/ubnt.sh create mode 100644 target/linux/ramips/dts/UBNT-ERX.dts create mode 100644 target/linux/ramips/mt7621/profiles/ubnt.mk diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index a55c9eb24f..719e9686ae 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -114,6 +114,7 @@ ramips_setup_interfaces() f5d8235-v2|\ hg255d|\ rt-n14u|\ + ubnt-erx|\ ur-326n4g|\ wrtnode|\ wt3020|\ diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index c002b975d7..62be04540e 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -349,6 +349,9 @@ ramips_board_detect() { *"TEW-692GR") name="tew-692gr" ;; + *"UBNT-ERX") + name="ubnt-erx" + ;; *"UR-326N4G") name="ur-326n4g" ;; @@ -399,7 +402,7 @@ ramips_board_detect() { ;; *"WizFi630A") name="wizfi630a" - ;; + ;; *"WL-330N") name="wl-330n" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 4ec3008b3e..f8073d19fe 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -182,12 +182,36 @@ platform_check_image() { } return 0 ;; + ubnt-erx) + nand_do_platform_check "$board" "$1" + return $?; + ;; esac echo "Sysupgrade is not yet supported on $board." return 1 } +platform_nand_pre_upgrade() { + local board=$(ramips_board_name) + + case "$board" in + ubnt-erx) + platform_upgrade_ubnt_erx "$ARGV" + ;; + esac +} + +platform_pre_upgrade() { + local board=$(ramips_board_name) + + case "$board" in + ubnt-erx) + nand_do_upgrade "$ARGV" + ;; + esac +} + platform_do_upgrade() { local board=$(ramips_board_name) diff --git a/target/linux/ramips/base-files/lib/upgrade/ubnt.sh b/target/linux/ramips/base-files/lib/upgrade/ubnt.sh new file mode 100644 index 0000000000..316a70444f --- /dev/null +++ b/target/linux/ramips/base-files/lib/upgrade/ubnt.sh @@ -0,0 +1,76 @@ +# +# Copyright (C) 2015 OpenWrt.org +# + +. /lib/functions.sh +#Note: this code also uses some functions from nand.sh, but it is expected to be run by nand.sh, so we are not +#sourcing it explicitly here + +UBNT_ERX_KERNEL_INDEX_OFFSET=160 + +ubnt_get_target_kernel() { + local factory_mtd=$1 + local current_kernel_index=$(hexdump -s $UBNT_ERX_KERNEL_INDEX_OFFSET -n 1 -e '/1 "%X "' ${factory_mtd}) + + if [ $current_kernel_index == "0" ]; then + echo 'kernel2' + elif [ $current_kernel_index == "1" ]; then + echo 'kernel1' + fi +} + +ubnt_update_target_kernel() { + local factory_mtd=$1 + local kernel_part=$2 + + local new_kernel_index + if [ $kernel_part == "kernel1" ]; then + new_kernel_index="\x00" + elif [ $kernel_part == "kernel2" ]; then + new_kernel_index="\x01" + else + echo 'Unknown kernel image index' >&2 + return 1 + fi + + if ! (echo -e $new_kernel_index | dd of=${factory_mtd} bs=1 count=1 seek=$UBNT_ERX_KERNEL_INDEX_OFFSET); then + echo 'Failed to update kernel bootup index' >&2 + return 1 + fi +} + +platform_upgrade_ubnt_erx() { + local factory_mtd=$(find_mtd_part factory) + if [ -z "$factory_mtd" ]; then + echo "cannot find factory partition" >&2 + exit 1 + fi + + local kernel_part="$(ubnt_get_target_kernel ${factory_mtd})" + if [ -z "$kernel_part" ]; then + echo "cannot find factory partition" >&2 + exit 1 + fi + + # This is a global defined in nand.sh, sets partition kernel will be flashed into + CI_KERNPART=${kernel_part} + + #Remove volume possibly left over from stock firmware + local ubidev="$( nand_find_ubi "$CI_UBIPART" )" + if [ -z "$ubidev" ]; then + local mtdnum="$( find_mtd_index "$CI_UBIPART" )" + if [ -z "$mtdnum" ]; then + echo "cannot find ubi mtd partition $CI_UBIPART" >&2 + exit 1 + fi + ubiattach -m "$mtdnum" + sync + ubidev="$( nand_find_ubi "$CI_UBIPART" )" + fi + if [ -n "$ubidev" ]; then + local troot_ubivol="$( nand_find_volume $ubidev troot )" + [ -n "$troot_ubivol" ] && ubirmvol /dev/$ubidev -N troot || true + fi + + ubnt_update_target_kernel ${factory_mtd} ${kernel_part} || exit 1 +} diff --git a/target/linux/ramips/dts/UBNT-ERX.dts b/target/linux/ramips/dts/UBNT-ERX.dts new file mode 100644 index 0000000000..0014ac766f --- /dev/null +++ b/target/linux/ramips/dts/UBNT-ERX.dts @@ -0,0 +1,119 @@ +#include + +/dts-v1/; + +#include "mt7621.dtsi" + +/ { + compatible = "mediatek,mt7621-eval-board", "mediatek,mt7621-soc"; + model = "UBNT-ERX"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + palmbus@1E000000 { + spi@b00 { + /* This board has 2Mb spi flash soldered in and visible + from manufacturer's firmware. + But this SoC shares spi and nand pins, + and current driver does't handle this sharing well */ + status = "disabled"; + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p80"; + reg = <1>; + linux,modalias = "m25p80"; + spi-max-frequency = <10000000>; + + partition@0 { + label = "spi"; + reg = <0x0 0x200000>; + read-only; + }; + }; + }; + }; + + nand@1e003000 { + compatible = "mtk,mt7621-nand"; + bank-width = <2>; + reg = <0x1e003000 0x800 + 0x1e003800 0x800>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x80000 0x60000>; + read-only; + }; + + factory: partition@e0000 { + label = "factory"; + reg = <0xe0000 0x60000>; + }; + + partition@140000 { + label = "kernel1"; + reg = <0x140000 0x300000>; + }; + + partition@440000 { + label = "kernel2"; + reg = <0x440000 0x300000>; + }; + + partition@740000 { + label = "ubi"; + reg = <0x740000 0xf7c0000>; + }; + + }; + + ethernet@1e100000 { + mtd-mac-address = <&factory 0x22>; + }; + + pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "uart2", "uart3", "i2c", "pcie", "rgmii2", "jtag"; + ralink,function = "gpio"; + }; + }; + }; + + sdhci@1E130000 { + status = "disabled"; + }; + + pcie@1e140000 { + status = "disabled"; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 12 1>; + linux,code = ; + }; + }; +}; diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile index 63d6222223..1b12249c82 100644 --- a/target/linux/ramips/image/Makefile +++ b/target/linux/ramips/image/Makefile @@ -69,6 +69,51 @@ define Build/relocate-kernel mv $@.new $@ endef +define Build/ubnt-erx-factory-compat + echo '21001:6' > $@.compat + $(TAR) -cf $@ --transform='s/^.*/compat/' $@.compat + $(RM) $@.compat +endef + +define Build/ubnt-erx-factory-kernel + if [ -e $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) ]; then \ + $(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp/' $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE); \ + \ + md5sum --binary $(BIN_DIR)/$(KERNEL_INITRAMFS_IMAGE) | awk '{print $$1}'> $@.md5; \ + $(TAR) -rf $@ --transform='s/^.*/vmlinux.tmp.md5/' $@.md5; \ + $(RM) $@.md5; \ + fi +endef + +define Build/ubnt-erx-factory-rootfs + echo "dummy" > $@.rootfs + $(TAR) -rf $@ --transform='s/^.*/squashfs.tmp/' $@.rootfs + + md5sum --binary $@.rootfs | awk '{print $$1}'> $@.md5 + $(TAR) -rf $@ --transform='s/^.*/squashfs.tmp.md5/' $@.md5 + $(RM) $@.md5 + $(RM) $@.rootfs +endef + +define Build/ubnt-erx-factory-version + echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $@.version + $(TAR) -rf $@ --transform='s/^.*/version.tmp/' $@.version + $(RM) $@.version +endef + +#We need kernel+initrams fit into kernel partition +define Build/ubnt-erx-factory-check-size + @[ $$(($(subst k,* 1024,$(subst m, * 1024k,$(1))))) -ge "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" ] || { \ + echo "WARNING: Initramfs kernel for image $@ is too big (kernel size: $$($(TAR) -xf $@ vmlinux.tmp -O | wc -c), max size $(1))" >&2; \ + $(RM) -f $@; \ + } + + @[ "$$($(TAR) -xf $@ vmlinux.tmp -O | wc -c)" -gt 0 ] || { \ + echo "WARNING: Kernel for image $@ not found" >&2; \ + $(RM) -f $@; \ + } +endef + define MkCombineduImage $(call PatchKernelLzma,$(2),$(3)) if [ `stat -c%s "$(KDIR)/vmlinux-$(2).bin.lzma"` -gt `expr $(4) - 64` ]; then \ @@ -954,7 +999,7 @@ endif # ifeq ($(SUBTARGET),mt7621) - TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 witi wf-2881 zbt-wg2626 + TARGET_DEVICES += mt7621 wsr-600 wsr-1166 dir-860l-b1 firewrt pbr-m1 re6500 sap-g3200u3 ubnt-erx witi wf-2881 zbt-wg2626 endif define Device/mt7621 @@ -1023,6 +1068,20 @@ define Device/wf-2881 IMAGE/sysupgrade.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE) endef +define Device/ubnt-erx + DTS := UBNT-ERX + FILESYSTEMS := squashfs + KERNEL_SIZE := 3145728 + KERNEL := $(KERNEL_DTB) | uImage lzma + IMAGES := sysupgrade.tar factory-initramfs.tar + IMAGE/factory-initramfs.tar := ubnt-erx-factory-compat | \ + ubnt-erx-factory-kernel | \ + ubnt-erx-factory-rootfs | \ + ubnt-erx-factory-version | \ + ubnt-erx-factory-check-size $$$$(KERNEL_SIZE) + IMAGE/sysupgrade.tar := sysupgrade-nand +endef + # # MT7628 Profiles # diff --git a/target/linux/ramips/mt7621/profiles/ubnt.mk b/target/linux/ramips/mt7621/profiles/ubnt.mk new file mode 100644 index 0000000000..b66b206694 --- /dev/null +++ b/target/linux/ramips/mt7621/profiles/ubnt.mk @@ -0,0 +1,17 @@ +# +# Copyright (C) 2015 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/UBNT-ERX + NAME:=Ubiquiti EdgeRouter X + FEATURES+=nand -usb + PACKAGES:=-kmod-mt76 -wpad-mini -kmod-cfg80211 +endef + +define Profile/UBNT-ERX/Description + Package set compatible with the Ubiquiti EdgeRouter X +endef +$(eval $(call Profile,UBNT-ERX)) -- 2.30.2