From a63aeaecf1f3387df020854c9b22a365207399ce Mon Sep 17 00:00:00 2001 From: Sander Vanheule Date: Thu, 28 Jul 2022 15:13:52 +0200 Subject: [PATCH] realtek: remove support for HPE 1920 series Support for HPE 1920 images depends on two non-existent tools (mkh3cimg and mkh3cvfs) from the in the firmware-utils package. Revert commit f2f09bc00280 ("realtek: add support for HPE 1920 series") until support for these tools is merged and made available in OpenWrt. Signed-off-by: Sander Vanheule --- .../realtek/base-files/etc/board.d/02_network | 18 +-- .../realtek/dts-5.10/rtl8380_hpe_1920-8g.dts | 113 ----------------- .../realtek/dts-5.10/rtl8382_hpe_1920-16g.dts | 48 ------- .../realtek/dts-5.10/rtl8382_hpe_1920-24g.dts | 68 ---------- .../realtek/dts-5.10/rtl8382_hpe_1920.dtsi | 117 ------------------ target/linux/realtek/dts-5.10/rtl838x.dtsi | 7 -- .../realtek/dts-5.10/rtl838x_hpe_1920.dtsi | 96 -------------- target/linux/realtek/image/Makefile | 49 -------- target/linux/realtek/image/rtl838x.mk | 24 ---- target/linux/realtek/rtl838x/config-5.10 | 3 - 10 files changed, 3 insertions(+), 540 deletions(-) delete mode 100644 target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts delete mode 100644 target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts delete mode 100644 target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts delete mode 100644 target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi delete mode 100644 target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network index 5356bcac65..af9db848dd 100644 --- a/target/linux/realtek/base-files/etc/board.d/02_network +++ b/target/linux/realtek/base-files/etc/board.d/02_network @@ -22,20 +22,9 @@ ucidef_set_bridge_device switch ucidef_set_interface_lan "$lan_list" lan_mac="" -lan_mac_start="" lan_mac_end="" label_mac="" case $board in -hpe,1920-8g|\ -hpe,1920-16g|\ -hpe,1920-24g) - label_mac=$(mtd_get_mac_binary factory 0x68) - lan_mac=$label_mac - mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null) - mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null) - lan_mac_start=$(macaddr_add $lan_mac 2) - lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1))) - ;; *) lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start) lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end) @@ -47,11 +36,10 @@ esac ucidef_set_interface_macaddr "lan" $lan_mac ucidef_set_bridge_mac "$lan_mac" ucidef_set_network_device_mac eth0 $lan_mac -[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac for lan in $lan_list; do - ucidef_set_network_device_mac $lan $lan_mac_start - [ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start) - lan_mac_start=$(macaddr_add $lan_mac_start 1) + ucidef_set_network_device_mac $lan $lan_mac + [ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac) + lan_mac=$(macaddr_add $lan_mac 1) done [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts deleted file mode 100644 index b51c75f355..0000000000 --- a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts +++ /dev/null @@ -1,113 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "rtl838x.dtsi" -#include "rtl838x_hpe_1920.dtsi" - -/ { - compatible = "hpe,1920-8g", "realtek,rtl838x-soc"; - model = "HPE 1920-8G (JG920A)"; - - gpio1: rtl8231-gpio { - compatible = "realtek,rtl8231-gpio"; - #gpio-cells = <2>; - gpio-controller; - indirect-access-bus-id = <0>; - }; - - i2c0: i2c-gpio-0 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp0: sfp-0 { - compatible = "sff,sfp"; - i2c-bus = <&i2c0>; - los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>; - // tx-fault and tx-disable unconnected - }; - - i2c1: i2c-gpio-1 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp1: sfp-1 { - compatible = "sff,sfp"; - i2c-bus = <&i2c1>; - los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>; - // tx-fault and tx-disable unconnected - }; -}; - -ðernet0 { - mdio: mdio-bus { - compatible = "realtek,rtl838x-mdio"; - regmap = <ðernet0>; - #address-cells = <1>; - #size-cells = <0>; - - INTERNAL_PHY(8) - INTERNAL_PHY(9) - INTERNAL_PHY(10) - INTERNAL_PHY(11) - INTERNAL_PHY(12) - INTERNAL_PHY(13) - INTERNAL_PHY(14) - INTERNAL_PHY(15) - - INTERNAL_PHY(24) - INTERNAL_PHY(26) - }; -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(8, 1, internal) - SWITCH_PORT(9, 2, internal) - SWITCH_PORT(10, 3, internal) - SWITCH_PORT(11, 4, internal) - SWITCH_PORT(12, 5, internal) - SWITCH_PORT(13, 6, internal) - SWITCH_PORT(14, 7, internal) - SWITCH_PORT(15, 8, internal) - - port@24 { - reg = <24>; - label = "lan9"; - phy-mode = "1000base-x"; - managed = "in-band-status"; - sfp = <&sfp0>; - }; - - port@26 { - reg = <26>; - label = "lan10"; - phy-mode = "1000base-x"; - managed = "in-band-status"; - sfp = <&sfp1>; - }; - - port@28 { - ethernet = <ðernet0>; - reg = <28>; - phy-mode = "internal"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts deleted file mode 100644 index 59043b2f6f..0000000000 --- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts +++ /dev/null @@ -1,48 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "rtl8382_hpe_1920.dtsi" - -/ { - compatible = "hpe,1920-16g", "realtek,rtl838x-soc"; - model = "HPE 1920-16G (JG923A)"; -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(8, 1, internal) - SWITCH_PORT(9, 2, internal) - SWITCH_PORT(10, 3, internal) - SWITCH_PORT(11, 4, internal) - SWITCH_PORT(12, 5, internal) - SWITCH_PORT(13, 6, internal) - SWITCH_PORT(14, 7, internal) - SWITCH_PORT(15, 8, internal) - - SWITCH_PORT(16, 9, qsgmii) - SWITCH_PORT(17, 10, qsgmii) - SWITCH_PORT(18, 11, qsgmii) - SWITCH_PORT(19, 12, qsgmii) - SWITCH_PORT(20, 13, qsgmii) - SWITCH_PORT(21, 14, qsgmii) - SWITCH_PORT(22, 15, qsgmii) - SWITCH_PORT(23, 16, qsgmii) - - SWITCH_PORT(24, 17, qsgmii) - SWITCH_PORT(25, 18, qsgmii) - SWITCH_PORT(26, 19, qsgmii) - SWITCH_PORT(27, 20, qsgmii) - - port@28 { - ethernet = <ðernet0>; - reg = <28>; - phy-mode = "internal"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts deleted file mode 100644 index 61781c708e..0000000000 --- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts +++ /dev/null @@ -1,68 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "rtl8382_hpe_1920.dtsi" - -/ { - compatible = "hpe,1920-24g", "realtek,rtl838x-soc"; - model = "HPE 1920-24G (JG924A)"; -}; - -&mdio { - EXTERNAL_PHY(0) - EXTERNAL_PHY(1) - EXTERNAL_PHY(2) - EXTERNAL_PHY(3) - EXTERNAL_PHY(4) - EXTERNAL_PHY(5) - EXTERNAL_PHY(6) - EXTERNAL_PHY(7) -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(0, 1, qsgmii) - SWITCH_PORT(1, 2, qsgmii) - SWITCH_PORT(2, 3, qsgmii) - SWITCH_PORT(3, 4, qsgmii) - SWITCH_PORT(4, 5, qsgmii) - SWITCH_PORT(5, 6, qsgmii) - SWITCH_PORT(6, 7, qsgmii) - SWITCH_PORT(7, 8, qsgmii) - - SWITCH_PORT(8, 9, internal) - SWITCH_PORT(9, 10, internal) - SWITCH_PORT(10, 11, internal) - SWITCH_PORT(11, 12, internal) - SWITCH_PORT(12, 13, internal) - SWITCH_PORT(13, 14, internal) - SWITCH_PORT(14, 15, internal) - SWITCH_PORT(15, 16, internal) - - SWITCH_PORT(16, 17, qsgmii) - SWITCH_PORT(17, 18, qsgmii) - SWITCH_PORT(18, 19, qsgmii) - SWITCH_PORT(19, 20, qsgmii) - SWITCH_PORT(20, 21, qsgmii) - SWITCH_PORT(21, 22, qsgmii) - SWITCH_PORT(22, 23, qsgmii) - SWITCH_PORT(23, 24, qsgmii) - - SWITCH_PORT(24, 25, qsgmii) - SWITCH_PORT(25, 26, qsgmii) - SWITCH_PORT(26, 27, qsgmii) - SWITCH_PORT(27, 28, qsgmii) - - port@28 { - ethernet = <ðernet0>; - reg = <28>; - phy-mode = "internal"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; -}; diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi deleted file mode 100644 index 5368b41c27..0000000000 --- a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi +++ /dev/null @@ -1,117 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "rtl838x.dtsi" -#include "rtl838x_hpe_1920.dtsi" - -/ { - gpio1: rtl8231-gpio { - compatible = "realtek,rtl8231-gpio"; - #gpio-cells = <2>; - gpio-controller; - indirect-access-bus-id = <0>; - }; - - i2c0: i2c-gpio-0 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp0: sfp-0 { - compatible = "sff,sfp"; - i2c-bus = <&i2c0>; - los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>; - // tx-fault unconnected - // tx-disable connected to RTL8214FC - }; - - i2c1: i2c-gpio-1 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp1: sfp-1 { - compatible = "sff,sfp"; - i2c-bus = <&i2c1>; - los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>; - // tx-fault unconnected - // tx-disable connected to RTL8214FC - }; - - i2c2: i2c-gpio-2 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp2: sfp-2 { - compatible = "sff,sfp"; - i2c-bus = <&i2c2>; - los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>; - // tx-fault unconnected - // tx-disable connected to RTL8214FC - }; - - i2c3: i2c-gpio-3 { - compatible = "i2c-gpio"; - sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - sfp3: sfp-3 { - compatible = "sff,sfp"; - i2c-bus = <&i2c3>; - los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>; - // tx-fault unconnected - // tx-disable connected to RTL8214FC - }; -}; - -ðernet0 { - mdio: mdio-bus { - compatible = "realtek,rtl838x-mdio"; - regmap = <ðernet0>; - #address-cells = <1>; - #size-cells = <0>; - - INTERNAL_PHY(8) - INTERNAL_PHY(9) - INTERNAL_PHY(10) - INTERNAL_PHY(11) - INTERNAL_PHY(12) - INTERNAL_PHY(13) - INTERNAL_PHY(14) - INTERNAL_PHY(15) - - EXTERNAL_PHY(16) - EXTERNAL_PHY(17) - EXTERNAL_PHY(18) - EXTERNAL_PHY(19) - EXTERNAL_PHY(20) - EXTERNAL_PHY(21) - EXTERNAL_PHY(22) - EXTERNAL_PHY(23) - - EXTERNAL_SFP_PHY_FULL(24, 0) - EXTERNAL_SFP_PHY_FULL(25, 1) - EXTERNAL_SFP_PHY_FULL(26, 2) - EXTERNAL_SFP_PHY_FULL(27, 3) - }; -}; diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi index 41fdbdae20..11cabc3f63 100644 --- a/target/linux/realtek/dts-5.10/rtl838x.dtsi +++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi @@ -27,13 +27,6 @@ reg = <##n>; \ }; -#define EXTERNAL_SFP_PHY_FULL(n, s) \ - phy##n: ethernet-phy@##n { \ - compatible = "ethernet-phy-ieee802.3-c22"; \ - sfp = <&sfp##s>; \ - reg = <##n>; \ - }; - #define SWITCH_PORT(n, s, m) \ port@##n { \ reg = <##n>; \ diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi deleted file mode 100644 index 8e29af62bb..0000000000 --- a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi +++ /dev/null @@ -1,96 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include -#include - -/ { - chosen { - bootargs = "console=ttyS0,38400"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x8000000>; - }; - - watchdog1: watchdog { - // PT7A7514 - compatible = "linux,wdt-gpio"; - gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; - hw_algo = "toggle"; - hw_margin_ms = <1000>; - always-running; - - pinctrl-names = "default"; - pinctrl-0 = <&pinmux_disable_sys_led>; - }; -}; - -&watchdog0 { - status = "disabled"; -}; - -&spi0 { - status = "okay"; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <50000000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "bootware_basic"; - reg = <0x0 0x50000>; - read-only; - }; - - partition@0x60000 { - label = "bootware_data"; - reg = <0x60000 0x30000>; - read-only; - }; - - partition@0x90000 { - label = "bootware_extend"; - reg = <0x90000 0x40000>; - read-only; - }; - - partition@0x100000 { - label = "bootware_basic_backup"; - reg = <0x100000 0x50000>; - read-only; - }; - - partition@0x160000 { - label = "bootware_data_backup"; - reg = <0x160000 0x30000>; - read-only; - }; - - partition@0x190000 { - label = "bootware_extend_backup"; - reg = <0x190000 0x40000>; - read-only; - }; - - partition@0x300000 { - label = "firmware"; - compatible = "h3c,vfs-firmware"; - reg = <0x300000 0x1cf0000>; - }; - - partition@0x1ff0000 { - label = "factory"; - reg = <0x1ff0000 0x10000>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile index 6165d99bfc..cf779002e8 100644 --- a/target/linux/realtek/image/Makefile +++ b/target/linux/realtek/image/Makefile @@ -8,7 +8,6 @@ KERNEL_ENTRY = 0x80000400 DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION -DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID define Build/zyxel-vers ( echo VERS;\ @@ -42,43 +41,6 @@ define Build/dlink-headers cat $@.kernel_part.hex $@.rootfs_part.hex > $@ endef -define Build/7z - $(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@) - mv $@.new $@ -endef - -define Build/h3c-image - $(STAGING_DIR_HOST)/bin/mkh3cimg \ - -i $(@) \ - -o $(@).new \ - -c 7z \ - -p $(H3C_PRODUCT_ID) \ - -d $(H3C_DEVICE_ID) - mv $@.new $@ -endef - -define Build/h3c-vfs - $(STAGING_DIR_HOST)/bin/mkh3cvfs \ - -i $(@) \ - -o $(@).new \ - -f openwrt-kernel.bin - mv $@.new $@ -endef - -define Build/relocate-kernel - rm -rf $@.relocate - $(CP) ../../generic/image/relocate $@.relocate - $(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \ - CROSS_COMPILE=$(TARGET_CROSS) - ( \ - dd if=$@.relocate/loader.bin bs=32 conv=sync && \ - perl -e '@s = stat("$@"); print pack("N", @s[7])' && \ - cat "$@" \ - ) > "$@.new" - mv "$@.new" "$@" - rm -rf $@.relocate -endef - define Device/Default PROFILES = Default KERNEL := kernel-bin | append-dtb | gzip | uImage gzip @@ -90,17 +52,6 @@ define Device/Default check-size | append-metadata endef -define Device/hpe_1920 - DEVICE_VENDOR := HPE - IMAGE_SIZE := 29632k - BLOCKSIZE := 64k - H3C_PRODUCT_ID := 0x3c010501 - KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs - KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image - IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \ - pad-rootfs | check-size | append-metadata -endef - # "NGE" refers to the uImage magic define Device/netgear_nge KERNEL := kernel-bin | append-dtb | lzma | uImage lzma diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk index 60eda5359d..887f82e385 100644 --- a/target/linux/realtek/image/rtl838x.mk +++ b/target/linux/realtek/image/rtl838x.mk @@ -65,30 +65,6 @@ define Device/engenius_ews2910p endef TARGET_DEVICES += engenius_ews2910p -define Device/hpe_1920-8g - $(Device/hpe_1920) - SOC := rtl8380 - DEVICE_MODEL := 1920-8G (JG920A) - H3C_DEVICE_ID := 0x00010023 -endef -TARGET_DEVICES += hpe_1920-8g - -define Device/hpe_1920-16g - $(Device/hpe_1920) - SOC := rtl8382 - DEVICE_MODEL := 1920-16G (JG923A) - H3C_DEVICE_ID := 0x00010026 -endef -TARGET_DEVICES += hpe_1920-16g - -define Device/hpe_1920-24g - $(Device/hpe_1920) - SOC := rtl8382 - DEVICE_MODEL := 1920-24G (JG924A) - H3C_DEVICE_ID := 0x00010027 -endef -TARGET_DEVICES += hpe_1920-24g - define Device/inaba_aml2-17gp SOC := rtl8382 IMAGE_SIZE := 13504k diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10 index 9075aa6d3c..c117fc489a 100644 --- a/target/linux/realtek/rtl838x/config-5.10 +++ b/target/linux/realtek/rtl838x/config-5.10 @@ -74,8 +74,6 @@ CONFIG_GPIO_PCA953X=y CONFIG_GPIO_PCA953X_IRQ=y CONFIG_GPIO_REALTEK_OTTO=y CONFIG_GPIO_RTL8231=y -CONFIG_GPIO_WATCHDOG=y -# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set CONFIG_GRO_CELLS=y CONFIG_HANDLE_DOMAIN_IRQ=y CONFIG_HARDWARE_WATCHPOINTS=y @@ -136,7 +134,6 @@ CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_BRNIMAGE_FW=y CONFIG_MTD_SPLIT_EVA_FW=y CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_H3C_VFS=y CONFIG_MTD_SPLIT_TPLINK_FW=y CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_NEED_DMA_MAP_STATE=y -- 2.30.2