+++ /dev/null
-/dts-v1/;
-
-#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/clock/qcom,rpmcc.h>
-#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Qualcomm IPQ8064";
- compatible = "qcom,ipq8064";
- interrupt-parent = <&intc>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- memory { device_type = "memory"; reg = <0 0>; };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- compatible = "qcom,krait";
- enable-method = "qcom,kpss-acc-v1";
- device_type = "cpu";
- reg = <0>;
- next-level-cache = <&L2>;
- qcom,acc = <&acpu0_aux>;
- qcom,saw = <&saw0>;
- clocks = <&kraitcc 0>, <&kraitcc 4>;
- clock-names = "cpu", "l2";
- clock-latency = <100000>;
- cpu-supply = <&smb208_s2a>;
- operating-points-v2 = <&opp_table0>;
- voltage-tolerance = <5>;
- cooling-min-state = <0>;
- cooling-max-state = <10>;
- #cooling-cells = <2>;
- cpu-idle-states = <&CPU_SPC>;
- };
-
- cpu1: cpu@1 {
- compatible = "qcom,krait";
- enable-method = "qcom,kpss-acc-v1";
- device_type = "cpu";
- reg = <1>;
- next-level-cache = <&L2>;
- qcom,acc = <&acpu1_aux>;
- qcom,saw = <&saw1>;
- clocks = <&kraitcc 1>, <&kraitcc 4>;
- clock-names = "cpu", "l2";
- clock-latency = <100000>;
- cpu-supply = <&smb208_s2b>;
- operating-points-v2 = <&opp_table0>;
- voltage-tolerance = <5>;
- cooling-min-state = <0>;
- cooling-max-state = <10>;
- #cooling-cells = <2>;
- cpu-idle-states = <&CPU_SPC>;
- };
-
- L2: l2-cache {
- compatible = "cache";
- cache-level = <2>;
- qcom,saw = <&saw_l2>;
- };
-
- qcom,l2 {
- qcom,l2-rates = <384000000 1000000000 1200000000>;
- qcom,l2-cpufreq = <384000000 600000000 1200000000>;
- qcom,l2-volt = <1100000 1100000 1150000>;
- qcom,l2-supply = <&smb208_s1a>;
- };
-
- idle-states {
- CPU_SPC: spc {
- compatible = "qcom,idle-state-spc",
- "arm,idle-state";
- status = "disabled";
- entry-latency-us = <400>;
- exit-latency-us = <900>;
- min-residency-us = <3000>;
- };
- };
- };
-
- opp_table0: opp_table0 {
- compatible = "operating-points-v2-qcom-cpu";
- nvmem-cells = <&speedbin_efuse>;
-
- opp-384000000 {
- opp-hz = /bits/ 64 <384000000>;
- opp-microvolt-speed0-pvs0-v0 = <1000000>;
- opp-microvolt-speed0-pvs1-v0 = <925000>;
- opp-microvolt-speed0-pvs2-v0 = <875000>;
- opp-microvolt-speed0-pvs3-v0 = <800000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- opp-600000000 {
- opp-hz = /bits/ 64 <600000000>;
- opp-microvolt-speed0-pvs0-v0 = <1050000>;
- opp-microvolt-speed0-pvs1-v0 = <975000>;
- opp-microvolt-speed0-pvs2-v0 = <925000>;
- opp-microvolt-speed0-pvs3-v0 = <850000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- opp-800000000 {
- opp-hz = /bits/ 64 <800000000>;
- opp-microvolt-speed0-pvs0-v0 = <1100000>;
- opp-microvolt-speed0-pvs1-v0 = <1025000>;
- opp-microvolt-speed0-pvs2-v0 = <995000>;
- opp-microvolt-speed0-pvs3-v0 = <900000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt-speed0-pvs0-v0 = <1150000>;
- opp-microvolt-speed0-pvs1-v0 = <1075000>;
- opp-microvolt-speed0-pvs2-v0 = <1025000>;
- opp-microvolt-speed0-pvs3-v0 = <950000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- opp-1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt-speed0-pvs0-v0 = <1200000>;
- opp-microvolt-speed0-pvs1-v0 = <1125000>;
- opp-microvolt-speed0-pvs2-v0 = <1075000>;
- opp-microvolt-speed0-pvs3-v0 = <1000000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- opp-1400000000 {
- opp-hz = /bits/ 64 <1400000000>;
- opp-microvolt-speed0-pvs0-v0 = <1250000>;
- opp-microvolt-speed0-pvs1-v0 = <1175000>;
- opp-microvolt-speed0-pvs2-v0 = <1125000>;
- opp-microvolt-speed0-pvs3-v0 = <1050000>;
- opp-supported-hw = <0x1>;
- clock-latency-ns = <100000>;
- };
-
- };
-
- thermal-zones {
- tsens_tz_sensor0 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 0>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor1 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 1>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor2 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 2>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor3 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 3>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor4 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 4>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor5 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 5>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor6 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 6>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor7 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 7>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor8 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 8>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor9 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 9>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
-
- tsens_tz_sensor10 {
- polling-delay-passive = <0>;
- polling-delay = <0>;
- thermal-sensors = <&tsens 10>;
-
- trips {
- cpu-critical-hi {
- temperature = <125000>;
- hysteresis = <2000>;
- type = "critical_high";
- };
-
- cpu-config-hi {
- temperature = <105000>;
- hysteresis = <2000>;
- type = "configurable_hi";
- };
-
- cpu-config-lo {
- temperature = <95000>;
- hysteresis = <2000>;
- type = "configurable_lo";
- };
-
- cpu-critical-low {
- temperature = <0>;
- hysteresis = <2000>;
- type = "critical_low";
- };
- };
- };
- };
-
- cpu-pmu {
- compatible = "qcom,krait-pmu";
- interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- nss@40000000 {
- reg = <0x40000000 0x1000000>;
- no-map;
- };
-
- smem: smem@41000000 {
- reg = <0x41000000 0x200000>;
- no-map;
- };
- };
-
- clocks {
- cxo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- pxo_board {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- sleep_clk: sleep_clk {
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- #clock-cells = <0>;
- };
- };
-
- fab-scaling {
- compatible = "qcom,fab-scaling";
- clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
- clock-names = "apps-fab-clk", "ddr-fab-clk";
- fab_freq_high = <533000000>;
- fab_freq_nominal = <400000000>;
- cpu_freq_threshold = <1000000000>;
- };
-
- firmware {
- scm {
- compatible = "qcom,scm-ipq806x";
- };
- };
-
- soc: soc {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- compatible = "simple-bus";
-
- lpass@28100000 {
- compatible = "qcom,lpass-cpu";
- status = "disabled";
- clocks = <&lcc AHBIX_CLK>,
- <&lcc MI2S_OSR_CLK>,
- <&lcc MI2S_BIT_CLK>;
- clock-names = "ahbix-clk",
- "mi2s-osr-clk",
- "mi2s-bit-clk";
- interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
- interrupt-names = "lpass-irq-lpaif";
- reg = <0x28100000 0x10000>;
- reg-names = "lpass-lpaif";
- };
-
- qfprom: qfprom@700000 {
- compatible = "qcom,qfprom", "syscon";
- reg = <0x700000 0x1000>;
- #address-cells = <1>;
- #size-cells = <1>;
- status = "okay";
- tsens_calib: calib@400 {
- reg = <0x400 0xb>;
- };
- tsens_backup: backup@410 {
- reg = <0x410 0xb>;
- };
- speedbin_efuse: speedbin@0c0 {
- reg = <0x0c0 0x4>;
- };
- };
-
- rpm: rpm@108000 {
- compatible = "qcom,rpm-ipq8064";
- reg = <0x108000 0x1000>;
- qcom,ipc = <&l2cc 0x8 2>;
-
- interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "ack",
- "err",
- "wakeup";
-
- clocks = <&gcc RPM_MSG_RAM_H_CLK>;
- clock-names = "ram";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- rpmcc: clock-controller {
- compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
- #clock-cells = <1>;
- };
-
- regulators {
- compatible = "qcom,rpm-smb208-regulators";
-
- smb208_s1a: s1a {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1150000>;
-
- qcom,switch-mode-frequency = <1200000>;
-
- };
-
- smb208_s1b: s1b {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1150000>;
-
- qcom,switch-mode-frequency = <1200000>;
- };
-
- smb208_s2a: s2a {
- regulator-min-microvolt = < 800000>;
- regulator-max-microvolt = <1250000>;
-
- qcom,switch-mode-frequency = <1200000>;
- };
-
- smb208_s2b: s2b {
- regulator-min-microvolt = < 800000>;
- regulator-max-microvolt = <1250000>;
-
- qcom,switch-mode-frequency = <1200000>;
- };
- };
- };
-
- rng@1a500000 {
- compatible = "qcom,prng";
- reg = <0x1a500000 0x200>;
- clocks = <&gcc PRNG_CLK>;
- clock-names = "core";
- };
-
- qcom_pinmux: pinmux@800000 {
- compatible = "qcom,ipq8064-pinctrl";
- reg = <0x800000 0x4000>;
-
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-
- pcie0_pins: pcie0_pinmux {
- mux {
- pins = "gpio3";
- function = "pcie1_rst";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- pcie1_pins: pcie1_pinmux {
- mux {
- pins = "gpio48";
- function = "pcie2_rst";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- pcie2_pins: pcie2_pinmux {
- mux {
- pins = "gpio63";
- function = "pcie3_rst";
- drive-strength = <12>;
- bias-disable;
- output-low;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "mdio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29",
- "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59",
- "gpio60", "gpio61", "gpio62";
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- leds_pins: leds_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9",
- "gpio26", "gpio53";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- output-low;
- };
- };
-
- buttons_pins: buttons_pins {
- mux {
- pins = "gpio54";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
- };
-
- intc: interrupt-controller@2000000 {
- compatible = "qcom,msm-qgic2";
- interrupt-controller;
- #interrupt-cells = <3>;
- reg = <0x02000000 0x1000>,
- <0x02002000 0x1000>;
- };
-
- timer@200a000 {
- compatible = "qcom,kpss-timer", "qcom,msm-timer";
- interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
- IRQ_TYPE_EDGE_RISING)>;
- reg = <0x0200a000 0x100>;
- clock-frequency = <25000000>,
- <32768>;
- clocks = <&sleep_clk>;
- clock-names = "sleep";
- cpu-offset = <0x80000>;
- };
-
- acpu0_aux: clock-controller@2088000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
- clock-output-names = "acpu0_aux";
- };
-
- acpu1_aux: clock-controller@2098000 {
- compatible = "qcom,kpss-acc-v1";
- reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
- clock-output-names = "acpu1_aux";
- };
-
- l2cc: clock-controller@2011000 {
- compatible = "qcom,kpss-gcc", "syscon";
- reg = <0x2011000 0x1000>;
- clock-output-names = "acpu_l2_aux";
- };
-
- kraitcc: clock-controller {
- compatible = "qcom,krait-cc-v1";
- #clock-cells = <1>;
- };
-
- saw0: regulator@2089000 {
- compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
- reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-
- saw1: regulator@2099000 {
- compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
- reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
- regulator;
- };
-
- saw_l2: regulator@02012000 {
- compatible = "qcom,saw2", "syscon";
- reg = <0x02012000 0x1000>;
- regulator;
- };
-
- sic_non_secure: sic-non-secure@12100000 {
- compatible = "syscon";
- reg = <0x12100000 0x10000>;
- };
-
- gsbi2: gsbi@12480000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <2>;
- reg = <0x12480000 0x100>;
- clocks = <&gcc GSBI2_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- status = "disabled";
-
- syscon-tcsr = <&tcsr>;
-
- gsbi2_serial: serial@12490000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x12490000 0x1000>,
- <0x12480000 0x1000>;
- interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
- };
-
- i2c@124a0000 {
- compatible = "qcom,i2c-qup-v1.1.1";
- reg = <0x124a0000 0x1000>;
- interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- };
-
- gsbi4: gsbi@16300000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <4>;
- reg = <0x16300000 0x100>;
- clocks = <&gcc GSBI4_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- status = "disabled";
-
- syscon-tcsr = <&tcsr>;
-
- gsbi4_serial: serial@16340000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x16340000 0x1000>,
- <0x16300000 0x1000>;
- interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
- };
-
- i2c@16380000 {
- compatible = "qcom,i2c-qup-v1.1.1";
- reg = <0x16380000 0x1000>;
- interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-
- gsbi5: gsbi@1a200000 {
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <5>;
- reg = <0x1a200000 0x100>;
- clocks = <&gcc GSBI5_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- status = "disabled";
-
- syscon-tcsr = <&tcsr>;
-
- gsbi5_serial: serial@1a240000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x1a240000 0x1000>,
- <0x1a200000 0x1000>;
- interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
- };
-
- i2c@1a280000 {
- compatible = "qcom,i2c-qup-v1.1.1";
- reg = <0x1a280000 0x1000>;
- interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi@1a280000 {
- compatible = "qcom,spi-qup-v1.1.1";
- reg = <0x1a280000 0x1000>;
- interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-
- gsbi7: gsbi@16600000 {
- status = "disabled";
- compatible = "qcom,gsbi-v1.0.0";
- cell-index = <7>;
- reg = <0x16600000 0x100>;
- clocks = <&gcc GSBI7_H_CLK>;
- clock-names = "iface";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- syscon-tcsr = <&tcsr>;
-
- gsbi7_serial: serial@16640000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x16640000 0x1000>,
- <0x16600000 0x1000>;
- interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
- };
- };
-
- sata_phy: sata-phy@1b400000 {
- compatible = "qcom,ipq806x-sata-phy";
- reg = <0x1b400000 0x200>;
-
- clocks = <&gcc SATA_PHY_CFG_CLK>;
- clock-names = "cfg";
-
- #phy-cells = <0>;
- status = "disabled";
- };
-
- sata: sata@29000000 {
- compatible = "qcom,ipq806x-ahci", "generic-ahci";
- reg = <0x29000000 0x180>;
-
- ports-implemented = <0x1>;
-
- interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&gcc SFAB_SATA_S_H_CLK>,
- <&gcc SATA_H_CLK>,
- <&gcc SATA_A_CLK>,
- <&gcc SATA_RXOOB_CLK>,
- <&gcc SATA_PMALIVE_CLK>;
- clock-names = "slave_face", "iface", "core",
- "rxoob", "pmalive";
-
- assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
- assigned-clock-rates = <100000000>, <100000000>;
-
- phys = <&sata_phy>;
- phy-names = "sata-phy";
- status = "disabled";
- };
-
- qcom,ssbi@500000 {
- compatible = "qcom,ssbi";
- reg = <0x00500000 0x1000>;
- qcom,controller-type = "pmic-arbiter";
- };
-
- gcc: clock-controller@900000 {
- compatible = "qcom,gcc-ipq8064";
- reg = <0x00900000 0x4000>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- #power-domain-cells = <1>;
- };
-
- tsens: thermal-sensor@900000 {
- compatible = "qcom,ipq8064-tsens";
- reg = <0x900000 0x3680>;
- nvmem-cells = <&tsens_calib>, <&tsens_backup>;
- nvmem-cell-names = "calib", "calib_backup";
- interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
- #thermal-sensor-cells = <1>;
- };
-
- tcsr: syscon@1a400000 {
- compatible = "qcom,tcsr-ipq8064", "syscon";
- reg = <0x1a400000 0x100>;
- };
-
- lcc: clock-controller@28000000 {
- compatible = "qcom,lcc-ipq8064";
- reg = <0x28000000 0x1000>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- sfpb_mutex_block: syscon@1200600 {
- compatible = "syscon";
- reg = <0x01200600 0x100>;
- };
-
- hs_phy_0: hs_phy_0 {
- compatible = "qcom,dwc3-hs-usb-phy";
- regmap = <&usb3_0>;
- clocks = <&gcc USB30_0_UTMI_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
- };
-
- ss_phy_0: ss_phy_0 {
- compatible = "qcom,dwc3-ss-usb-phy";
- regmap = <&usb3_0>;
- clocks = <&gcc USB30_0_MASTER_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
- };
-
- usb3_0: usb3@110f8800 {
- compatible = "qcom,dwc3", "syscon";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x110f8800 0x8000>;
- clocks = <&gcc USB30_0_MASTER_CLK>;
- clock-names = "core";
-
- ranges;
-
- resets = <&gcc USB30_0_MASTER_RESET>;
- reset-names = "master";
-
- status = "disabled";
-
- dwc3_0: dwc3@11000000 {
- compatible = "snps,dwc3";
- reg = <0x11000000 0xcd00>;
- interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&hs_phy_0>, <&ss_phy_0>;
- phy-names = "usb2-phy", "usb3-phy";
- dr_mode = "host";
- snps,dis_u3_susphy_quirk;
- };
- };
-
- hs_phy_1: hs_phy_1 {
- compatible = "qcom,dwc3-hs-usb-phy";
- regmap = <&usb3_1>;
- clocks = <&gcc USB30_1_UTMI_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
- };
-
- ss_phy_1: ss_phy_1 {
- compatible = "qcom,dwc3-ss-usb-phy";
- regmap = <&usb3_1>;
- clocks = <&gcc USB30_1_MASTER_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
- };
-
- usb3_1: usb3@100f8800 {
- compatible = "qcom,dwc3", "syscon";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x100f8800 0x8000>;
- clocks = <&gcc USB30_1_MASTER_CLK>;
- clock-names = "core";
-
- ranges;
-
- resets = <&gcc USB30_1_MASTER_RESET>;
- reset-names = "master";
-
- status = "disabled";
-
- dwc3_1: dwc3@10000000 {
- compatible = "snps,dwc3";
- reg = <0x10000000 0xcd00>;
- interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&hs_phy_1>, <&ss_phy_1>;
- phy-names = "usb2-phy", "usb3-phy";
- dr_mode = "host";
- snps,dis_u3_susphy_quirk;
- };
- };
-
- pcie0: pci@1b500000 {
- compatible = "qcom,pcie-ipq8064";
- reg = <0x1b500000 0x1000
- 0x1b502000 0x80
- 0x1b600000 0x100
- 0x0ff00000 0x100000>;
- reg-names = "dbi", "elbi", "parf", "config";
- device_type = "pci";
- linux,pci-domain = <0>;
- bus-range = <0x00 0xff>;
- num-lanes = <1>;
- #address-cells = <3>;
- #size-cells = <2>;
-
- ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
- 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
-
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "msi";
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
- <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
- <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
- <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
- clocks = <&gcc PCIE_A_CLK>,
- <&gcc PCIE_H_CLK>,
- <&gcc PCIE_PHY_CLK>,
- <&gcc PCIE_AUX_CLK>,
- <&gcc PCIE_ALT_REF_CLK>;
- clock-names = "core", "iface", "phy", "aux", "ref";
-
- assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
- assigned-clock-rates = <100000000>;
-
- resets = <&gcc PCIE_ACLK_RESET>,
- <&gcc PCIE_HCLK_RESET>,
- <&gcc PCIE_POR_RESET>,
- <&gcc PCIE_PCI_RESET>,
- <&gcc PCIE_PHY_RESET>,
- <&gcc PCIE_EXT_RESET>;
- reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
-
- perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
-
- status = "disabled";
- };
-
- pcie1: pci@1b700000 {
- compatible = "qcom,pcie-ipq8064";
- reg = <0x1b700000 0x1000
- 0x1b702000 0x80
- 0x1b800000 0x100
- 0x31f00000 0x100000>;
- reg-names = "dbi", "elbi", "parf", "config";
- device_type = "pci";
- linux,pci-domain = <1>;
- bus-range = <0x00 0xff>;
- num-lanes = <1>;
- #address-cells = <3>;
- #size-cells = <2>;
-
- ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
- 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
-
- interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "msi";
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
- <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
- <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
- <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
- clocks = <&gcc PCIE_1_A_CLK>,
- <&gcc PCIE_1_H_CLK>,
- <&gcc PCIE_1_PHY_CLK>,
- <&gcc PCIE_1_AUX_CLK>,
- <&gcc PCIE_1_ALT_REF_CLK>;
- clock-names = "core", "iface", "phy", "aux", "ref";
-
- assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
- assigned-clock-rates = <100000000>;
-
- resets = <&gcc PCIE_1_ACLK_RESET>,
- <&gcc PCIE_1_HCLK_RESET>,
- <&gcc PCIE_1_POR_RESET>,
- <&gcc PCIE_1_PCI_RESET>,
- <&gcc PCIE_1_PHY_RESET>,
- <&gcc PCIE_1_EXT_RESET>;
- reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
-
- perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
-
- status = "disabled";
- };
-
- pcie2: pci@1b900000 {
- compatible = "qcom,pcie-ipq8064";
- reg = <0x1b900000 0x1000
- 0x1b902000 0x80
- 0x1ba00000 0x100
- 0x35f00000 0x100000>;
- reg-names = "dbi", "elbi", "parf", "config";
- device_type = "pci";
- linux,pci-domain = <2>;
- bus-range = <0x00 0xff>;
- num-lanes = <1>;
- #address-cells = <3>;
- #size-cells = <2>;
-
- ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
- 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
-
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "msi";
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
- <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
- <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
- <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
- clocks = <&gcc PCIE_2_A_CLK>,
- <&gcc PCIE_2_H_CLK>,
- <&gcc PCIE_2_PHY_CLK>,
- <&gcc PCIE_2_AUX_CLK>,
- <&gcc PCIE_2_ALT_REF_CLK>;
- clock-names = "core", "iface", "phy", "aux", "ref";
-
- assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
- assigned-clock-rates = <100000000>;
-
- resets = <&gcc PCIE_2_ACLK_RESET>,
- <&gcc PCIE_2_HCLK_RESET>,
- <&gcc PCIE_2_POR_RESET>,
- <&gcc PCIE_2_PCI_RESET>,
- <&gcc PCIE_2_PHY_RESET>,
- <&gcc PCIE_2_EXT_RESET>;
- reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
-
- pinctrl-0 = <&pcie2_pins>;
- pinctrl-names = "default";
-
- perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
-
- status = "disabled";
- };
-
- adm_dma: dma@18300000 {
- compatible = "qcom,adm";
- reg = <0x18300000 0x100000>;
- interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
- #dma-cells = <1>;
-
- clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
- clock-names = "core", "iface";
-
- resets = <&gcc ADM0_RESET>,
- <&gcc ADM0_PBUS_RESET>,
- <&gcc ADM0_C0_RESET>,
- <&gcc ADM0_C1_RESET>,
- <&gcc ADM0_C2_RESET>;
- reset-names = "clk", "pbus", "c0", "c1", "c2";
- qcom,ee = <0>;
-
- status = "disabled";
- };
-
- nand_controller: nand-controller@1ac00000 {
- compatible = "qcom,ipq806x-nand";
- reg = <0x1ac00000 0x800>;
-
- clocks = <&gcc EBI2_CLK>,
- <&gcc EBI2_AON_CLK>;
- clock-names = "core", "aon";
-
- dmas = <&adm_dma 3>;
- dma-names = "rxtx";
- qcom,cmd-crci = <15>;
- qcom,data-crci = <3>;
-
- status = "disabled";
-
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- nss_common: syscon@03000000 {
- compatible = "syscon";
- reg = <0x03000000 0x0000FFFF>;
- };
-
- qsgmii_csr: syscon@1bb00000 {
- compatible = "syscon";
- reg = <0x1bb00000 0x000001FF>;
- };
-
- stmmac_axi_setup: stmmac-axi-config {
- snps,wr_osr_lmt = <7>;
- snps,rd_osr_lmt = <7>;
- snps,blen = <16 0 0 0 0 0 0>;
- };
-
- mdio0: mdio@37000000 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- compatible = "qcom,ipq8064-mdio", "syscon";
- reg = <0x37000000 0x200000>;
- resets = <&gcc GMAC_CORE1_RESET>;
- reset-names = "stmmaceth";
- clocks = <&gcc GMAC_CORE1_CLK>;
- clock-names = "stmmaceth";
-
- status = "disabled";
- };
-
- gmac0: ethernet@37000000 {
- device_type = "network";
- compatible = "qcom,ipq806x-gmac";
- reg = <0x37000000 0x200000>;
- interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
-
- snps,axi-config = <&stmmac_axi_setup>;
- snps,pbl = <32>;
- snps,aal = <1>;
-
- qcom,nss-common = <&nss_common>;
- qcom,qsgmii-csr = <&qsgmii_csr>;
-
- clocks = <&gcc GMAC_CORE1_CLK>;
- clock-names = "stmmaceth";
-
- resets = <&gcc GMAC_CORE1_RESET>;
- reset-names = "stmmaceth";
-
- status = "disabled";
- };
-
- gmac1: ethernet@37200000 {
- device_type = "network";
- compatible = "qcom,ipq806x-gmac";
- reg = <0x37200000 0x200000>;
- interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
-
- snps,axi-config = <&stmmac_axi_setup>;
- snps,pbl = <32>;
- snps,aal = <1>;
-
- qcom,nss-common = <&nss_common>;
- qcom,qsgmii-csr = <&qsgmii_csr>;
-
- clocks = <&gcc GMAC_CORE2_CLK>;
- clock-names = "stmmaceth";
-
- resets = <&gcc GMAC_CORE2_RESET>;
- reset-names = "stmmaceth";
-
- status = "disabled";
- };
-
- gmac2: ethernet@37400000 {
- device_type = "network";
- compatible = "qcom,ipq806x-gmac", "snps,dwmac";
- reg = <0x37400000 0x200000>;
- interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
-
- snps,axi-config = <&stmmac_axi_setup>;
- snps,pbl = <32>;
- snps,aal = <1>;
-
- qcom,nss-common = <&nss_common>;
- qcom,qsgmii-csr = <&qsgmii_csr>;
-
- clocks = <&gcc GMAC_CORE3_CLK>;
- clock-names = "stmmaceth";
-
- resets = <&gcc GMAC_CORE3_RESET>;
- reset-names = "stmmaceth";
-
- status = "disabled";
- };
-
- gmac3: ethernet@37600000 {
- device_type = "network";
- compatible = "qcom,ipq806x-gmac", "snps,dwmac";
- reg = <0x37600000 0x200000>;
- interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
-
- snps,axi-config = <&stmmac_axi_setup>;
- snps,pbl = <32>;
- snps,aal = <1>;
-
- qcom,nss-common = <&nss_common>;
- qcom,qsgmii-csr = <&qsgmii_csr>;
-
- clocks = <&gcc GMAC_CORE4_CLK>;
- clock-names = "stmmaceth";
-
- resets = <&gcc GMAC_CORE4_RESET>;
- reset-names = "stmmaceth";
-
- status = "disabled";
- };
-
- /* Temporary fixed regulator */
- vsdcc_fixed: vsdcc-regulator {
- compatible = "regulator-fixed";
- regulator-name = "SDCC Power";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- sdcc1bam: dma@12402000 {
- compatible = "qcom,bam-v1.3.0";
- reg = <0x12402000 0x8000>;
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc SDC1_H_CLK>;
- clock-names = "bam_clk";
- #dma-cells = <1>;
- qcom,ee = <0>;
- };
-
- sdcc3bam: dma@12182000 {
- compatible = "qcom,bam-v1.3.0";
- reg = <0x12182000 0x8000>;
- interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&gcc SDC3_H_CLK>;
- clock-names = "bam_clk";
- #dma-cells = <1>;
- qcom,ee = <0>;
- };
-
- amba: amba {
- compatible = "arm,amba-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- sdcc1: sdcc@12400000 {
- status = "disabled";
- compatible = "arm,pl18x", "arm,primecell";
- arm,primecell-periphid = <0x00051180>;
- reg = <0x12400000 0x2000>;
- interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "cmd_irq";
- clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
- clock-names = "mclk", "apb_pclk";
- bus-width = <8>;
- max-frequency = <96000000>;
- non-removable;
- cap-sd-highspeed;
- cap-mmc-highspeed;
- vmmc-supply = <&vsdcc_fixed>;
- dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
- dma-names = "tx", "rx";
- };
-
- sdcc3: sdcc@12180000 {
- compatible = "arm,pl18x", "arm,primecell";
- arm,primecell-periphid = <0x00051180>;
- status = "disabled";
- reg = <0x12180000 0x2000>;
- interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "cmd_irq";
- clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
- clock-names = "mclk", "apb_pclk";
- bus-width = <8>;
- cap-sd-highspeed;
- cap-mmc-highspeed;
- max-frequency = <192000000>;
- #mmc-ddr-1_8v;
- sd-uhs-sdr104;
- sd-uhs-ddr50;
- vqmmc-supply = <&vsdcc_fixed>;
- dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
- dma-names = "tx", "rx";
- };
- };
- };
-
- sfpb_mutex: sfpb-mutex {
- compatible = "qcom,sfpb-mutex";
- syscon = <&sfpb_mutex_block 4 4>;
-
- #hwlock-cells = <1>;
- };
-
- smem {
- compatible = "qcom,smem";
- memory-region = <&smem>;
- hwlocks = <&sfpb_mutex 3>;
- };
-};
--- /dev/null
+--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
+@@ -8,6 +8,8 @@
+ #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+ #include <dt-bindings/soc/qcom,gsbi.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
++#include <dt-bindings/mfd/qcom-rpm.h>
++#include <dt-bindings/clock/qcom,rpmcc.h>
+
+ / {
+ #address-cells = <1>;
+@@ -28,6 +30,16 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
++ clocks = <&kraitcc 0>, <&kraitcc 4>;
++ clock-names = "cpu", "l2";
++ clock-latency = <100000>;
++ cpu-supply = <&smb208_s2a>;
++ operating-points-v2 = <&opp_table0>;
++ voltage-tolerance = <5>;
++ cooling-min-state = <0>;
++ cooling-max-state = <10>;
++ #cooling-cells = <2>;
++ cpu-idle-states = <&CPU_SPC>;
+ };
+
+ cpu1: cpu@1 {
+@@ -38,11 +50,458 @@
+ next-level-cache = <&L2>;
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
++ clocks = <&kraitcc 1>, <&kraitcc 4>;
++ clock-names = "cpu", "l2";
++ clock-latency = <100000>;
++ cpu-supply = <&smb208_s2b>;
++ operating-points-v2 = <&opp_table0>;
++ voltage-tolerance = <5>;
++ cooling-min-state = <0>;
++ cooling-max-state = <10>;
++ #cooling-cells = <2>;
++ cpu-idle-states = <&CPU_SPC>;
+ };
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
++ qcom,saw = <&saw_l2>;
++ };
++
++ qcom,l2 {
++ qcom,l2-rates = <384000000 1000000000 1200000000>;
++ qcom,l2-cpufreq = <384000000 600000000 1200000000>;
++ qcom,l2-volt = <1100000 1100000 1150000>;
++ qcom,l2-supply = <&smb208_s1a>;
++ };
++
++ idle-states {
++ CPU_SPC: spc {
++ compatible = "qcom,idle-state-spc", "arm,idle-state";
++ status = "disabled";
++ entry-latency-us = <400>;
++ exit-latency-us = <900>;
++ min-residency-us = <3000>;
++ };
++ };
++ };
++
++ opp_table0: opp_table0 {
++ compatible = "operating-points-v2-qcom-cpu";
++ nvmem-cells = <&speedbin_efuse>;
++
++ opp-384000000 {
++ opp-hz = /bits/ 64 <384000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1000000>;
++ opp-microvolt-speed0-pvs1-v0 = <925000>;
++ opp-microvolt-speed0-pvs2-v0 = <875000>;
++ opp-microvolt-speed0-pvs3-v0 = <800000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++
++ opp-600000000 {
++ opp-hz = /bits/ 64 <600000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1050000>;
++ opp-microvolt-speed0-pvs1-v0 = <975000>;
++ opp-microvolt-speed0-pvs2-v0 = <925000>;
++ opp-microvolt-speed0-pvs3-v0 = <850000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++
++ opp-800000000 {
++ opp-hz = /bits/ 64 <800000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1100000>;
++ opp-microvolt-speed0-pvs1-v0 = <1025000>;
++ opp-microvolt-speed0-pvs2-v0 = <995000>;
++ opp-microvolt-speed0-pvs3-v0 = <900000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++
++ opp-1000000000 {
++ opp-hz = /bits/ 64 <1000000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1150000>;
++ opp-microvolt-speed0-pvs1-v0 = <1075000>;
++ opp-microvolt-speed0-pvs2-v0 = <1025000>;
++ opp-microvolt-speed0-pvs3-v0 = <950000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++
++ opp-1200000000 {
++ opp-hz = /bits/ 64 <1200000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1200000>;
++ opp-microvolt-speed0-pvs1-v0 = <1125000>;
++ opp-microvolt-speed0-pvs2-v0 = <1075000>;
++ opp-microvolt-speed0-pvs3-v0 = <1000000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++
++ opp-1400000000 {
++ opp-hz = /bits/ 64 <1400000000>;
++ opp-microvolt-speed0-pvs0-v0 = <1250000>;
++ opp-microvolt-speed0-pvs1-v0 = <1175000>;
++ opp-microvolt-speed0-pvs2-v0 = <1125000>;
++ opp-microvolt-speed0-pvs3-v0 = <1050000>;
++ opp-supported-hw = <0x1>;
++ clock-latency-ns = <100000>;
++ };
++ };
++
++ thermal-zones {
++ tsens_tz_sensor0 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 0>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor1 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 1>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor2 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 2>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor3 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 3>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor4 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 4>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor5 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 5>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor6 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 6>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor7 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 7>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor8 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 8>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor9 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 9>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
++ };
++
++ tsens_tz_sensor10 {
++ polling-delay-passive = <0>;
++ polling-delay = <0>;
++ thermal-sensors = <&tsens 10>;
++
++ trips {
++ cpu-critical-hi {
++ temperature = <125000>;
++ hysteresis = <2000>;
++ type = "critical_high";
++ };
++
++ cpu-config-hi {
++ temperature = <105000>;
++ hysteresis = <2000>;
++ type = "configurable_hi";
++ };
++
++ cpu-config-lo {
++ temperature = <95000>;
++ hysteresis = <2000>;
++ type = "configurable_lo";
++ };
++
++ cpu-critical-low {
++ temperature = <0>;
++ hysteresis = <2000>;
++ type = "critical_low";
++ };
++ };
+ };
+ };
+
+@@ -93,6 +552,15 @@
+ };
+ };
+
++ fab-scaling {
++ compatible = "qcom,fab-scaling";
++ clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
++ clock-names = "apps-fab-clk", "ddr-fab-clk";
++ fab_freq_high = <533000000>;
++ fab_freq_nominal = <400000000>;
++ cpu_freq_threshold = <1000000000>;
++ };
++
+ firmware {
+ scm {
+ compatible = "qcom,scm-ipq806x", "qcom,scm";
+@@ -120,6 +588,84 @@
+ reg-names = "lpass-lpaif";
+ };
+
++ qfprom: qfprom@700000 {
++ compatible = "qcom,qfprom", "syscon";
++ reg = <0x700000 0x1000>;
++ #address-cells = <1>;
++ #size-cells = <1>;
++ status = "okay";
++ tsens_calib: calib@400 {
++ reg = <0x400 0xb>;
++ };
++ tsens_backup: backup@410 {
++ reg = <0x410 0xb>;
++ };
++ speedbin_efuse: speedbin@0c0 {
++ reg = <0x0c0 0x4>;
++ };
++ };
++
++ rpm: rpm@108000 {
++ compatible = "qcom,rpm-ipq8064";
++ reg = <0x108000 0x1000>;
++ qcom,ipc = <&l2cc 0x8 2>;
++
++ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
++ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
++ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "ack", "err", "wakeup";
++
++ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
++ clock-names = "ram";
++
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ rpmcc: clock-controller {
++ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
++ #clock-cells = <1>;
++ };
++
++ regulators {
++ compatible = "qcom,rpm-smb208-regulators";
++
++ smb208_s1a: s1a {
++ regulator-min-microvolt = <1050000>;
++ regulator-max-microvolt = <1150000>;
++
++ qcom,switch-mode-frequency = <1200000>;
++ };
++
++ smb208_s1b: s1b {
++ regulator-min-microvolt = <1050000>;
++ regulator-max-microvolt = <1150000>;
++
++ qcom,switch-mode-frequency = <1200000>;
++ };
++
++ smb208_s2a: s2a {
++ regulator-min-microvolt = < 800000>;
++ regulator-max-microvolt = <1250000>;
++
++ qcom,switch-mode-frequency = <1200000>;
++ };
++
++ smb208_s2b: s2b {
++ regulator-min-microvolt = < 800000>;
++ regulator-max-microvolt = <1250000>;
++
++ qcom,switch-mode-frequency = <1200000>;
++ };
++ };
++ };
++
++ rng@1a500000 {
++ compatible = "qcom,prng";
++ reg = <0x1a500000 0x200>;
++ clocks = <&gcc PRNG_CLK>;
++ clock-names = "core";
++ };
++
+ qcom_pinmux: pinmux@800000 {
+ compatible = "qcom,ipq8064-pinctrl";
+ reg = <0x800000 0x4000>;
+@@ -159,6 +705,15 @@
+ };
+ };
+
++ i2c4_pins: i2c4_pinmux {
++ mux {
++ pins = "gpio12", "gpio13";
++ function = "gsbi4";
++ drive-strength = <12>;
++ bias-disable;
++ };
++ };
++
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+@@ -168,6 +723,53 @@
+ };
+ };
+
++ nand_pins: nand_pins {
++ disable {
++ pins = "gpio34", "gpio35", "gpio36",
++ "gpio37", "gpio38";
++ function = "nand";
++ drive-strength = <10>;
++ bias-disable;
++ };
++
++ pullups {
++ pins = "gpio39";
++ function = "nand";
++ drive-strength = <10>;
++ bias-pull-up;
++ };
++
++ hold {
++ pins = "gpio40", "gpio41", "gpio42",
++ "gpio43", "gpio44", "gpio45",
++ "gpio46", "gpio47";
++ function = "nand";
++ drive-strength = <10>;
++ bias-bus-hold;
++ };
++ };
++
++ mdio0_pins: mdio0_pins {
++ mux {
++ pins = "gpio0", "gpio1";
++ function = "mdio";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
++ rgmii2_pins: rgmii2_pins {
++ mux {
++ pins = "gpio27", "gpio28", "gpio29",
++ "gpio30", "gpio31", "gpio32",
++ "gpio51", "gpio52", "gpio59",
++ "gpio60", "gpio61", "gpio62";
++ function = "rgmii2";
++ drive-strength = <8>;
++ bias-disable;
++ };
++ };
++
+ leds_pins: leds_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9",
+@@ -229,6 +831,17 @@
+ clock-output-names = "acpu1_aux";
+ };
+
++ l2cc: clock-controller@2011000 {
++ compatible = "qcom,kpss-gcc", "syscon";
++ reg = <0x2011000 0x1000>;
++ clock-output-names = "acpu_l2_aux";
++ };
++
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
++ };
++
+ saw0: regulator@2089000 {
+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
+ reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+@@ -241,6 +854,17 @@
+ regulator;
+ };
+
++ saw_l2: regulator@02012000 {
++ compatible = "qcom,saw2", "syscon";
++ reg = <0x02012000 0x1000>;
++ regulator;
++ };
++
++ sic_non_secure: sic-non-secure@12100000 {
++ compatible = "syscon";
++ reg = <0x12100000 0x10000>;
++ };
++
+ gsbi2: gsbi@12480000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <2>;
+@@ -436,6 +1060,15 @@
+ #power-domain-cells = <1>;
+ };
+
++ tsens: thermal-sensor@900000 {
++ compatible = "qcom,ipq8064-tsens";
++ reg = <0x900000 0x3680>;
++ nvmem-cells = <&tsens_calib>, <&tsens_backup>;
++ nvmem-cell-names = "calib", "calib_backup";
++ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
++ #thermal-sensor-cells = <1>;
++ };
++
+ tcsr: syscon@1a400000 {
+ compatible = "qcom,tcsr-ipq8064", "syscon";
+ reg = <0x1a400000 0x100>;
+@@ -448,6 +1081,95 @@
+ #reset-cells = <1>;
+ };
+
++ sfpb_mutex_block: syscon@1200600 {
++ compatible = "syscon";
++ reg = <0x01200600 0x100>;
++ };
++
++ hs_phy_0: hs_phy_0 {
++ compatible = "qcom,dwc3-hs-usb-phy";
++ regmap = <&usb3_0>;
++ clocks = <&gcc USB30_0_UTMI_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++ };
++
++ ss_phy_0: ss_phy_0 {
++ compatible = "qcom,dwc3-ss-usb-phy";
++ regmap = <&usb3_0>;
++ clocks = <&gcc USB30_0_MASTER_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++ };
++
++ usb3_0: usb3@110f8800 {
++ compatible = "qcom,dwc3", "syscon";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ reg = <0x110f8800 0x8000>;
++ clocks = <&gcc USB30_0_MASTER_CLK>;
++ clock-names = "core";
++
++ ranges;
++
++ resets = <&gcc USB30_0_MASTER_RESET>;
++ reset-names = "master";
++
++ status = "disabled";
++
++ dwc3_0: dwc3@11000000 {
++ compatible = "snps,dwc3";
++ reg = <0x11000000 0xcd00>;
++ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
++ phys = <&hs_phy_0>, <&ss_phy_0>;
++ phy-names = "usb2-phy", "usb3-phy";
++ dr_mode = "host";
++ snps,dis_u3_susphy_quirk;
++ };
++ };
++
++ hs_phy_1: hs_phy_1 {
++ compatible = "qcom,dwc3-hs-usb-phy";
++ regmap = <&usb3_1>;
++ clocks = <&gcc USB30_1_UTMI_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++ };
++
++ ss_phy_1: ss_phy_1 {
++ compatible = "qcom,dwc3-ss-usb-phy";
++ regmap = <&usb3_1>;
++ clocks = <&gcc USB30_1_MASTER_CLK>;
++ clock-names = "ref";
++ #phy-cells = <0>;
++ };
++
++ usb3_1: usb3@100f8800 {
++ compatible = "qcom,dwc3", "syscon";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ reg = <0x100f8800 0x8000>;
++ clocks = <&gcc USB30_1_MASTER_CLK>;
++ clock-names = "core";
++
++ ranges;
++
++ resets = <&gcc USB30_1_MASTER_RESET>;
++ reset-names = "master";
++
++ status = "disabled";
++
++ dwc3_1: dwc3@10000000 {
++ compatible = "snps,dwc3";
++ reg = <0x10000000 0xcd00>;
++ interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
++ phys = <&hs_phy_1>, <&ss_phy_1>;
++ phy-names = "usb2-phy", "usb3-phy";
++ dr_mode = "host";
++ snps,dis_u3_susphy_quirk;
++ };
++ };
++
+ pcie0: pci@1b500000 {
+ compatible = "qcom,pcie-ipq8064";
+ reg = <0x1b500000 0x1000
+@@ -601,6 +1323,167 @@
+ perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+ };
+
++ adm_dma: dma@18300000 {
++ compatible = "qcom,adm";
++ reg = <0x18300000 0x100000>;
++ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
++ #dma-cells = <1>;
++
++ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
++ clock-names = "core", "iface";
++
++ resets = <&gcc ADM0_RESET>,
++ <&gcc ADM0_PBUS_RESET>,
++ <&gcc ADM0_C0_RESET>,
++ <&gcc ADM0_C1_RESET>,
++ <&gcc ADM0_C2_RESET>;
++ reset-names = "clk", "pbus", "c0", "c1", "c2";
++ qcom,ee = <0>;
++
++ status = "disabled";
++ };
++
++ nand_controller: nand-controller@1ac00000 {
++ compatible = "qcom,ipq806x-nand";
++ reg = <0x1ac00000 0x800>;
++
++ clocks = <&gcc EBI2_CLK>,
++ <&gcc EBI2_AON_CLK>;
++ clock-names = "core", "aon";
++
++ dmas = <&adm_dma 3>;
++ dma-names = "rxtx";
++ qcom,cmd-crci = <15>;
++ qcom,data-crci = <3>;
++
++ status = "disabled";
++
++ #address-cells = <1>;
++ #size-cells = <0>;
++ };
++
++ nss_common: syscon@03000000 {
++ compatible = "syscon";
++ reg = <0x03000000 0x0000FFFF>;
++ };
++
++ qsgmii_csr: syscon@1bb00000 {
++ compatible = "syscon";
++ reg = <0x1bb00000 0x000001FF>;
++ };
++
++ stmmac_axi_setup: stmmac-axi-config {
++ snps,wr_osr_lmt = <7>;
++ snps,rd_osr_lmt = <7>;
++ snps,blen = <16 0 0 0 0 0 0>;
++ };
++
++ mdio0: mdio@37000000 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ compatible = "qcom,ipq8064-mdio", "syscon";
++ reg = <0x37000000 0x200000>;
++ resets = <&gcc GMAC_CORE1_RESET>;
++ reset-names = "stmmaceth";
++ clocks = <&gcc GMAC_CORE1_CLK>;
++ clock-names = "stmmaceth";
++
++ status = "disabled";
++ };
++
++ gmac0: ethernet@37000000 {
++ device_type = "network";
++ compatible = "qcom,ipq806x-gmac";
++ reg = <0x37000000 0x200000>;
++ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "macirq";
++
++ snps,axi-config = <&stmmac_axi_setup>;
++ snps,pbl = <32>;
++ snps,aal = <1>;
++
++ qcom,nss-common = <&nss_common>;
++ qcom,qsgmii-csr = <&qsgmii_csr>;
++
++ clocks = <&gcc GMAC_CORE1_CLK>;
++ clock-names = "stmmaceth";
++
++ resets = <&gcc GMAC_CORE1_RESET>;
++ reset-names = "stmmaceth";
++
++ status = "disabled";
++ };
++
++ gmac1: ethernet@37200000 {
++ device_type = "network";
++ compatible = "qcom,ipq806x-gmac";
++ reg = <0x37200000 0x200000>;
++ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "macirq";
++
++ snps,axi-config = <&stmmac_axi_setup>;
++ snps,pbl = <32>;
++ snps,aal = <1>;
++
++ qcom,nss-common = <&nss_common>;
++ qcom,qsgmii-csr = <&qsgmii_csr>;
++
++ clocks = <&gcc GMAC_CORE2_CLK>;
++ clock-names = "stmmaceth";
++
++ resets = <&gcc GMAC_CORE2_RESET>;
++ reset-names = "stmmaceth";
++
++ status = "disabled";
++ };
++
++ gmac2: ethernet@37400000 {
++ device_type = "network";
++ compatible = "qcom,ipq806x-gmac", "snps,dwmac";
++ reg = <0x37400000 0x200000>;
++ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "macirq";
++
++ snps,axi-config = <&stmmac_axi_setup>;
++ snps,pbl = <32>;
++ snps,aal = <1>;
++
++ qcom,nss-common = <&nss_common>;
++ qcom,qsgmii-csr = <&qsgmii_csr>;
++
++ clocks = <&gcc GMAC_CORE3_CLK>;
++ clock-names = "stmmaceth";
++
++ resets = <&gcc GMAC_CORE3_RESET>;
++ reset-names = "stmmaceth";
++
++ status = "disabled";
++ };
++
++ gmac3: ethernet@37600000 {
++ device_type = "network";
++ compatible = "qcom,ipq806x-gmac", "snps,dwmac";
++ reg = <0x37600000 0x200000>;
++ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "macirq";
++
++ snps,axi-config = <&stmmac_axi_setup>;
++ snps,pbl = <32>;
++ snps,aal = <1>;
++
++ qcom,nss-common = <&nss_common>;
++ qcom,qsgmii-csr = <&qsgmii_csr>;
++
++ clocks = <&gcc GMAC_CORE4_CLK>;
++ clock-names = "stmmaceth";
++
++ resets = <&gcc GMAC_CORE4_RESET>;
++ reset-names = "stmmaceth";
++
++ status = "disabled";
++ };
++
+ vsdcc_fixed: vsdcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCC Power";
+@@ -676,4 +1559,17 @@
+ };
+ };
+ };
++
++ sfpb_mutex: sfpb-mutex {
++ compatible = "qcom,sfpb-mutex";
++ syscon = <&sfpb_mutex_block 4 4>;
++
++ #hwlock-cells = <1>;
++ };
++
++ smem {
++ compatible = "qcom,smem";
++ memory-region = <&smem>;
++ hwlocks = <&sfpb_mutex 3>;
++ };
+ };
projects / openwrt / staging / rmilecki.git / commitdiff