ath79: Add support for OpenMesh OM5P-AC v2
authorSven Eckelmann <sven@narfation.org>
Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)
committerHauke Mehrtens <hauke@hauke-m.de>
Thu, 10 Feb 2022 23:28:52 +0000 (00:28 +0100)
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8031 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

This device support is based on the partially working stub from commit
53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon").

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 1699c1dc7f26b332f868d338457abfbe716d6ba0)

target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts
target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
target/linux/ath79/image/generic.mk

index b4d452dda19de7986f75f1e7a6f647b1d517014d..a478f04a74a18a966f8b962f17abc8560b19f6b3 100644 (file)
@@ -7,26 +7,34 @@
 
 / {
        compatible = "openmesh,om5p-ac-v2", "qca,qca9558";
-       model = "OpenMesh OM5P-AC V2";
+       model = "OpenMesh OM5P-AC v2";
 
-       extosc: ref {
-               compatible = "fixed-clock";
-               #clock-cells = <0>;
-               clock-output-names = "ref";
-               clock-frequency = <40000000>;
+       chosen {
+               /delete-property/ bootargs;
+       };
+
+       aliases {
+               serial0 = &uart;
+               led-boot = &led_power_blue;
+               led-failsafe = &led_power_blue;
+               led-running = &led_power_blue;
+               led-upgrade = &led_power_blue;
+               label-mac-device = &eth0;
        };
 
        leds {
                compatible = "gpio-leds";
 
-               power {
-                       label = "blue:power";
-                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
-               };
-
                wifi_green {
                        label = "green:wifi";
                        gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               led_power_blue: power_blue {
+                       label = "blue:power";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+                       default-state = "on";
                };
 
                wifi_yellow {
                };
        };
 
+       i2c {
+               compatible = "i2c-gpio";
+               gpios = <&gpio 19 GPIO_ACTIVE_HIGH /* sda */
+                        &gpio 18 GPIO_ACTIVE_HIGH /* scl */
+                       >;
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               i2c-gpio,scl-open-drain;
+               i2c-gpio,sda-open-drain;
+
+               tmp423a@4e {
+                       compatible = "ti,tmp423";
+                       reg = <0x4e>;
+               };
+       };
+
+       watchdog {
+               compatible = "linux,wdt-gpio";
+               gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+               hw_algo = "toggle";
+               /* hw_margin_ms is actually 300s but driver limits it to 60s */
+               hw_margin_ms = <60000>;
+               always-running;
+       };
+
        gpio-export {
                compatible = "gpio-export";
                #size-cells = <0>;
 
 &pinmux {
        pinmux_pa_dcdc_pins {
-               pinctrl-single,bits = <0x0 0xff00 0x0>;
+               pinctrl-single,bits = <0x0 0x0 0xff0000>;
        };
 
        pinmux_pa_high_pins {
-               pinctrl-single,bits = <0x10 0xff 0x0>;
+               pinctrl-single,bits = <0x10 0x0 0xff>;
        };
 };
 
        status = "okay";
 };
 
-&pll {
-       clocks = <&extosc>;
-};
-
 &spi {
        status = "okay";
 
                reg = <0>;
                spi-max-frequency = <25000000>;
 
+               /* partitions are passed via bootloader */
                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                                read-only;
                        };
 
-                       partition@1 {
+                       partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };
 
-                       partition@2 {
-                               compatible = "denx,uimage";
-                               label = "firmware";
+                       partition@50000 {
+                               label = "custom";
+                               reg = <0x050000 0x060000>;
+                               read-only;
+                       };
+
+                       partition@b0000 {
+                               label = "inactive";
+                               reg = <0x0b0000 0x7a0000>;
+                       };
+
+                       partition@850000 {
+                               label = "inactive2";
                                reg = <0x850000 0x7a0000>;
                        };
 
-                       partition@3 {
-                               label = "art";
+                       art: partition@ff0000 {
+                               label = "ART";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
 &mdio0 {
        status = "okay";
 
+       phy-mask = <0x10>;
+
        phy4: ethernet-phy@4 {
                reg = <4>;
-               phy-mode = "rgmii-id";
+               eee-broken-100tx;
+               eee-broken-1000t;
        };
 };
 
 &mdio1 {
        status = "okay";
 
+       phy-mask = <0x2>;
+
        phy1: ethernet-phy@1 {
                reg = <1>;
-               phy-mode = "sgmii";
+               eee-broken-100tx;
+               eee-broken-1000t;
+               at803x-override-sgmii-link-check;
        };
 };
 
 
        pll-data = <0x82000101 0x80000101 0x80001313>;
 
+       mtd-mac-address = <&art 0x0>;
+
+       phy-mode = "rgmii-id";
        phy-handle = <&phy4>;
+
+       gmac-config {
+               device = <&gmac>;
+               rgmii-enabled = <1>;
+               rxd-delay = <2>;
+               rxdv-delay = <2>;
+               txd-delay = <0>;
+               txen-delay = <0>;
+       };
 };
 
 &eth1 {
 
        pll-data = <0x03000101 0x80000101 0x80001313>;
 
+       mtd-mac-address = <&art 0x6>;
+
+       qca955x-sgmii-fixup;
+
        phy-handle = <&phy1>;
 };
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&art 0x0>;
+       mac-address-increment = <2>;
+};
index 14103a73106f83b7cdecf400b75d317b4a1e3cf3..69735f336070a48ddad76c72c2876bcd775c56a1 100644 (file)
@@ -100,12 +100,9 @@ case "$FIRMWARE" in
                ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
                ;;
        openmesh,mr1750-v1|\
-       openmesh,mr1750-v2)
-               caldata_extract "ART" 0x5000 0x844
-               ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
-               ;;
+       openmesh,mr1750-v2|\
        openmesh,om5p-ac-v2)
-               caldata_extract "art" 0x5000 0x844
+               caldata_extract "ART" 0x5000 0x844
                ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
                ;;
        qihoo,c301)
index f8b1c13677d6485c4b095057f7cf3317ea262104..1240ef51e88ed2e5d24088746596da085c01ab5c 100644 (file)
@@ -78,7 +78,8 @@ platform_do_upgrade() {
        openmesh,om2p-hs-v3|\
        openmesh,om2p-hs-v4|\
        openmesh,om2p-lc|\
-       openmesh,om5p)
+       openmesh,om5p|\
+       openmesh,om5p-ac-v2)
                PART_NAME="inactive"
                platform_do_upgrade_openmesh "$1"
                ;;
index ac9fa2b3de5e9e535e27f99d6aae194db7d3efb0..304e58980062465ba7955e5fe45dbd6b0097937b 100644 (file)
@@ -1781,12 +1781,12 @@ endef
 TARGET_DEVICES += openmesh_om5p
 
 define Device/openmesh_om5p-ac-v2
+  $(Device/openmesh_common_64k)
   SOC := qca9558
-  DEVICE_VENDOR := OpenMesh
   DEVICE_MODEL := OM5P-AC
   DEVICE_VARIANT := v2
-  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
-  IMAGE_SIZE := 7808k
+  DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  OPENMESH_CE_TYPE := OM5PAC
   SUPPORTED_DEVICES += om5p-acv2
 endef
 TARGET_DEVICES += openmesh_om5p-ac-v2