#include "qcom-ipq8064-v1.0.dtsi"
#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Netgear Nighthawk X4 R7500";
};
aliases {
- serial0 = &uart4;
mdio-gpio0 = &mdio0;
led-boot = &power_white;
chosen {
bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
};
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
+ };
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ usb1 {
+ label = "white:usb1";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
};
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
+ usb2 {
+ label = "white:usb2";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
};
- sata-phy@1b400000 {
- status = "ok";
+ power_amber: power_amber {
+ label = "amber:power";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
};
- sata@29000000 {
- status = "ok";
+ wan_white {
+ label = "white:wan";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
};
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
+ wan_amber {
+ label = "amber:wan";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
};
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
+ wps {
+ label = "white:wps";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
};
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
+ esata {
+ label = "white:esata";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
};
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
+ power_white: power_white {
+ label = "white:power";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
};
- usb30@0 {
- status = "ok";
+ wifi {
+ label = "white:wifi";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
};
+ };
+};
- usb30@1 {
- status = "ok";
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };
- pcie0: pci@1b500000 {
- status = "ok";
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };
+};
- pcie1: pci@1b700000 {
- status = "ok";
- };
+&gsbi5 {
+ status = "disabled";
- nand@1ac00000 {
- status = "ok";
+ spi@1a280000 {
+ status = "disabled";
+ };
+};
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
+&hs_phy_0 {
+ status = "okay";
+};
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
+&ss_phy_0 {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&hs_phy_1 {
+ status = "okay";
+};
+
+&ss_phy_1 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+&pcie1 {
+ status = "okay";
+ max-link-speed = <1>;
+};
+
+&nand {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ nand-is-boot-medium;
+ qcom,boot-partitions = <0x0 0x1180000>;
+
+ partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
kernel@1340000 {
label = "kernel";
- reg = <0x1340000 0x0200000>;
+ reg = <0x1340000 0x0400000>;
};
- ubi@1540000 {
+ ubi@1740000 {
label = "ubi";
- reg = <0x1540000 0x1800000>;
+ reg = <0x1740000 0x1600000>;
};
netgear@2d40000 {
reg = <0x3940000 0x46c0000>;
read-only;
};
+ };
+ };
+};
- firmware@1340000 {
- label = "firmware";
- reg = <0x1340000 0x1a00000>;
- };
+&mdio0 {
+ status = "okay";
- };
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10>;
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
+ ports {
#address-cells = <1>;
#size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
+ port@0 {
reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <1000>;
+ rx-internal-delay-ps = <1000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
};
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&phy_port1>;
};
- };
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&phy_port2>;
+ };
- mtd-mac-address = <&art 6>;
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-mode = "internal";
+ phy-handle = <&phy_port3>;
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-mode = "internal";
+ phy-handle = <&phy_port4>;
};
- };
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-mode = "internal";
+ phy-handle = <&phy_port5>;
+ };
- mtd-mac-address = <&art 0>;
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac2>;
+ phy-mode = "sgmii";
+ qca,sgmii-enable-pll;
- fixed-link {
- speed = <1000>;
- full-duplex;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
};
};
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
+ phy_port1: phy@0 {
+ reg = <0>;
+ };
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
+ phy_port4: phy@3 {
+ reg = <3>;
+ };
+
+ phy_port5: phy@4 {
+ reg = <4>;
+ };
};
};
+};
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
- usb1 {
- label = "r7500:white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
- usb2 {
- label = "r7500:white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
+ nvmem-cells = <&macaddr_art_6>;
+ nvmem-cell-names = "mac-address";
- power_amber: power_amber {
- label = "r7500:amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
- wan_white {
- label = "r7500:white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
- wan_amber {
- label = "r7500:amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
- wps {
- label = "r7500:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
- esata {
- label = "r7500:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
+&tcsr {
+ qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
+ compatible = "qcom,tcsr";
+};
- power_white: power_white {
- label = "r7500:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
+&adm_dma {
+ status = "okay";
+};
- wifi {
- label = "r7500:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
+&art {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr@0 {
+ reg = <0x0 0x6>;
};
-};
-&adm_dma {
- status = "ok";
+ macaddr_art_6: macaddr@6 {
+ reg = <0x6 0x6>;
+ };
};
projects / openwrt / openwrt.git / blobdiff