include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
-DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
-
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR := 0x80208000
+ DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
+ IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
IMAGE/sysupgrade.bin/squashfs :=
endef
-define Device/FitImage
- KERNEL_SUFFIX := -fit-uImage.itb
- KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- KERNEL_NAME := Image
-endef
-
-define Device/FitImageLzma
- KERNEL_SUFFIX := -fit-uImage.itb
- KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- KERNEL_NAME := Image
-endef
-
-define Device/FitzImage
- KERNEL_SUFFIX := -fit-zImage.itb
- KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- KERNEL_NAME := zImage
-endef
-
-define Device/UbiFit
- KERNEL_IN_UBI := 1
- IMAGES := nand-factory.ubi nand-sysupgrade.bin
- IMAGE/nand-factory.ubi := append-ubi
- IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
-endef
-
-define Device/DniImage
- KERNEL_SUFFIX := -fit-uImage.itb
- KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
- KERNEL_NAME := Image
- NETGEAR_BOARD_ID :=
- NETGEAR_HW_ID :=
- IMAGES := factory.img sysupgrade.bin
- IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
- IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
-endef
-DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
-
-
-define Device/8dev_jalapeno
- $(call Device/FitImage)
- $(call Device/UbiFit)
- DEVICE_DTS := qcom-ipq4018-jalapeno
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- DEVICE_TITLE := 8devices Jalapeno
-endef
-TARGET_DEVICES += 8dev_jalapeno
-
-define Device/alfa-network_ap120c-ac
- $(call Device/FitImage)
- $(call Device/UbiFit)
- DEVICE_TITLE := ALFA Network AP120C-AC
- DEVICE_DTS := qcom-ipq4018-ap120c-ac
- DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ac kmod-usb-acm \
- kmod-tpm-i2c-atmel uboot-envtools
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- IMAGE_SIZE := 65536k
- IMAGES := nand-factory.bin nand-sysupgrade.bin
- IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
-endef
-TARGET_DEVICES += alfa-network_ap120c-ac
-
-define Device/asus_map-ac2200
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4019-map-ac2200
- DEVICE_TITLE := ASUS Lyra MAP-AC2200
- IMAGES := sysupgrade.bin
- DEVICE_PACKAGES := ipq-wifi-asus_map-ac2200 ath10k-firmware-qca9888-ct kmod-ath3k
-endef
-TARGET_DEVICES += asus_map-ac2200
-
-define Device/asus_rt-ac58u
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4018-rt-ac58u
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- DTB_SIZE := 65536
- DEVICE_TITLE := Asus RT-AC58U
- IMAGE_SIZE := 20439364
- FILESYSTEMS := squashfs
-# Someone - in their infinite wisdom - decided to put the firmware
-# version in front of the image name \03\00\00\04 => Version 3.0.0.4
-# Since u-boot works with strings we either need another fixup step
-# to add a version... or we are very careful not to add '\0' into that
-# string and call it a day.... Yeah, we do the latter!
- UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
- IMAGES := sysupgrade.bin
- DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
-endef
-TARGET_DEVICES += asus_rt-ac58u
-
-define Device/avm_fritzbox-4040
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4018-fritz4040
- BOARD_NAME := fritz4040
- DEVICE_TITLE := AVM Fritz!Box 4040
- IMAGE_SIZE := 29753344
- UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
- UBOOT_PARTITION_SIZE := 524288
- IMAGES = eva.bin sysupgrade.bin
- IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := fritz-tffs fritz-caldata
-endef
-TARGET_DEVICES += avm_fritzbox-4040
-
-define Device/compex_wpj428
- $(call Device/FitImage)
- DEVICE_DTS := qcom-ipq4028-wpj428
- DEVICE_DTS_CONFIG := config@4
- BLOCKSIZE := 64k
- DEVICE_TITLE := Compex WPJ428
- IMAGE_SIZE := 31232k
- KERNEL_SIZE := 4096k
- IMAGES = sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := kmod-gpio-beeper
-endef
-TARGET_DEVICES += compex_wpj428
-
-define Device/engenius_eap1300
- $(call Device/FitImage)
- DEVICE_TITLE := EnGenius EAP1300
- DEVICE_DTS_CONFIG := config@4
- BOARD_NAME := eap1300
- DEVICE_DTS := qcom-ipq4018-eap1300
- KERNEL_SIZE := 5120k
- IMAGE_SIZE := 25344k
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := ipq-wifi-engenius_eap1300
-endef
-TARGET_DEVICES += engenius_eap1300
-
-define Device/glinet_gl-b1300
- $(call Device/FitImage)
- DEVICE_TITLE := GL.iNet GL-B1300
- BOARD_NAME := gl-b1300
- DEVICE_DTS := qcom-ipq4029-gl-b1300
- KERNEL_SIZE := 4096k
- IMAGE_SIZE := 26624k
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
-endef
-TARGET_DEVICES += glinet_gl-b1300
-
-define Device/linksys_ea6350v3
- # The Linksys EA6350v3 has a uboot bootloader that does not
- # support either booting lzma kernel images nor booting UBI
- # partitions. This uboot, however, supports raw kernel images and
- # gzipped images.
- #
- # As for the time of writing this, the device will boot the kernel
- # from a fixed address with a fixed length of 3MiB. Also, the
- # device has a hard-coded kernel command line that requieres the
- # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
- # Oh... and the kernel partition overlaps with the rootfs
- # partition (the same for alt_kernel and alt_rootfs).
- #
- # If you are planing re-partitioning the device, you may want to
- # keep those details in mind:
- # 1. The kernel adresses you should honor are 0x00000000 and
- # 0x02800000 respectively.
- # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
- # 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
- # 4. The kernel command line from uboot is harcoded to boot with
- # rootfs either in mtd11 or mtd13.
- $(call Device/FitzImage)
- DEVICE_TITLE := Linksys EA6350v3
- DEVICE_DTS := qcom-ipq4018-ea6350v3
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- KERNEL_SIZE := 3145728
- IMAGE_SIZE := 38797312
- UBINIZE_OPTS := -E 5
- IMAGES := factory.bin sysupgrade.bin
- IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
- DEVICE_PACKAGES := ipq-wifi-linksys_ea6350v3 uboot-envtools
-endef
-TARGET_DEVICES += linksys_ea6350v3
-
-define Device/meraki_mr33
- $(call Device/FitImage)
- DEVICE_DTS := qcom-ipq4029-mr33
- BLOCKSIZE := 131072
- PAGESIZE := 2048
- DEVICE_TITLE := Cisco Meraki MR33
- IMAGES = sysupgrade.bin
- DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
-endef
-TARGET_DEVICES += meraki_mr33
-
-define Device/netgear_ex61x0v2
- $(call Device/DniImage)
- DEVICE_DTS_CONFIG := config@4
- NETGEAR_BOARD_ID := EX6150v2series
- NETGEAR_HW_ID := 29765285+16+0+128+2x2
-endef
-
-define Device/netgear_ex6100v2
- $(call Device/netgear_ex61x0v2)
- DEVICE_DTS := qcom-ipq4018-ex6100v2
- DEVICE_TITLE := Netgear EX6100v2
-endef
-TARGET_DEVICES += netgear_ex6100v2
-
-define Device/netgear_ex6150v2
- $(call Device/netgear_ex61x0v2)
- DEVICE_DTS := qcom-ipq4018-ex6150v2
- DEVICE_TITLE := Netgear EX6150v2
-endef
-TARGET_DEVICES += netgear_ex6150v2
-
-define Device/openmesh_a42
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4018-a42
- DEVICE_DTS_CONFIG := config@om.a42
- BLOCKSIZE := 64k
- DEVICE_TITLE := OpenMesh A42
- KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
- IMAGE_SIZE := 15616k
- IMAGES = factory.bin sysupgrade.bin
- IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
- IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
- DEVICE_PACKAGES := uboot-envtools
-endef
-TARGET_DEVICES += openmesh_a42
-
-define Device/openmesh_a62
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4019-a62
- DEVICE_DTS_CONFIG := config@om.a62
- BLOCKSIZE := 64k
- DEVICE_TITLE := OpenMesh A62
- KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
- IMAGE_SIZE := 15552k
- IMAGES = factory.bin sysupgrade.bin
- IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
- IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
- DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
-endef
-
-TARGET_DEVICES += openmesh_a62
-
-define Device/qcom_ap-dk01.1-c1
- DEVICE_TITLE := QCA AP-DK01.1-C1
- BOARD_NAME := ap-dk01.1-c1
- DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
- KERNEL_INSTALL := 1
- KERNEL_SIZE := 4096k
- IMAGE_SIZE := 26624k
- $(call Device/FitImage)
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
-endef
-TARGET_DEVICES += qcom_ap-dk01.1-c1
-
-define Device/qcom_ap-dk04.1-c1
- $(call Device/FitImage)
- $(call Device/UbiFit)
- DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
- KERNEL_INSTALL := 1
- KERNEL_SIZE := 4048k
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- BOARD_NAME := ap-dk04.1-c1
- DEVICE_TITLE := QCA AP-DK04.1-C1
-endef
-TARGET_DEVICES += qcom_ap-dk04.1-c1
-
-define Device/qxwlan_e2600ac-c1
- $(call Device/FitImage)
- DEVICE_TITLE := Qxwlan E2600AC-C1 (nor flash)
- BOARD_NAME := e2600ac-c1
- DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
- KERNEL_SIZE := 4096k
- IMAGE_SIZE := 31232k
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
-endef
-TARGET_DEVICES += qxwlan_e2600ac-c1
-
-define Device/qxwlan_e2600ac-c2
- $(call Device/FitImage)
- $(call Device/UbiFit)
- DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
- KERNEL_INSTALL := 1
- BLOCKSIZE := 128k
- PAGESIZE := 2048
- DEVICE_TITLE := Qxwlan E2600AC-C2 (nornand flash)
- DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
-endef
-TARGET_DEVICES += qxwlan_e2600ac-c2
-
-define Device/zyxel_nbg6617
- $(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4018-nbg6617
- DEVICE_TITLE := ZyXEL NBG6617
- ROOTFS_SIZE := 24960k
- RAS_BOARD := NBG6617
- RAS_ROOTFS_SIZE := 19840k
- RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- IMAGES := sysupgrade.bin factory.bin
-# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
-# at least as large as the one of the initial firmware image (not the current
-# one on the device). This only applies to the Web-UI, the bootlaoder ignores
-# this minimum-size. However, the larger image can be flashed both ways.
- IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
- IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
- DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
-endef
-TARGET_DEVICES += zyxel_nbg6617
-
-define Device/zyxel_wre6606
- $(call Device/FitImage)
- DEVICE_TITLE := ZyXEL WRE6606
- DEVICE_DTS_CONFIG := config@4
- DEVICE_DTS := qcom-ipq4018-wre6606
- IMAGES := sysupgrade.bin
- IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
-endef
-TARGET_DEVICES += zyxel_wre6606
+include $(SUBTARGET).mk
$(eval $(call BuildImage))
projects / openwrt / staging / dedeckeh.git / blobdiff