// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
+
+#include "ar9344.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include "ar9344.dtsi"
-
/ {
model = "Winchannel WB2000";
compatible = "winchannel,wb2000", "qca,ar9344";
compatible = "gpio-leds";
wlan2g {
- label = "wb2000:green:2g";
+ label = "green:2g";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tpt";
};
usb {
- label = "wb2000:green:usb";
+ label = "green:usb";
gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
- trigger-sources = <&hub_port1>, <&hub_port2>;
+ trigger-sources = <&hub_port>;
linux,default-trigger = "usbport";
};
led_system: system {
- label = "wb2000:green:system";
+ label = "green:system";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
default-state = "on";
};
compatible = "gpio-leds";
wlan {
- label = "wb2000:green:5g";
+ label = "green:5g";
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
clock-frequency = <40000000>;
};
-&uart {
- status = "okay";
-};
-
&spi {
- num-cs = <1>;
-
status = "okay";
flash@0 {
read-only;
};
- art: partition@fe0000 {
+ partition@fe0000 {
label = "art";
reg = <0xfe0000 0x10000>;
read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ calibration_art_1000: calibration@1000 {
+ reg = <0x1000 0x440>;
+ };
+
+ calibration_art_5000: calibration@5000 {
+ reg = <0x5000 0x440>;
+ };
+ };
};
- addr: partition@ff0000 {
+ partition@ff0000 {
label = "addr";
reg = <0xff0000 0x10000>;
read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_addr_0: macaddr@0 {
+ compatible = "mac-base";
+ reg = <0x0 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
};
};
};
ath9k: wifi@0,0 {
compatible = "pci168c,0030";
reg = <0x0000 0 0 0 0>;
- qca,no-eeprom;
- mtd-mac-address = <&addr 0x0>;
- mtd-mac-address-increment = <0x10>;
+ nvmem-cells = <&macaddr_addr_0 0x10>, <&calibration_art_5000>;
+ nvmem-cell-names = "mac-address", "calibration";
#gpio-cells = <2>;
gpio-controller;
};
};
&usb {
- #address-cells = <1>;
- #size-cells = <0>;
status = "okay";
-
- port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
- #trigger-source-cells = <0>;
-
- hub_port1: port@1 {
- reg = <1>;
- #trigger-source-cells = <0>;
- };
-
- hub_port2: port@2 {
- reg = <2>;
- #trigger-source-cells = <0>;
- };
- };
};
&usb_phy {
&wmac {
status = "okay";
- mtd-cal-data = <&art 0x1000>;
- mtd-mac-address = <&addr 0x0>;
+ nvmem-cells = <&macaddr_addr_0 0>, <&calibration_art_1000>;
+ nvmem-cell-names = "mac-address", "calibration";
};
&mdio0 {
status = "okay";
- phy-mask = <0x10>;
-
phy4: ethernet-phy@4 {
reg = <4>;
};
pll-data = <0xe000000 0x04000101 0x04001313>;
- mtd-mac-address = <&addr 0x0>;
- mtd-mac-address-increment = <0x21>;
+ nvmem-cells = <&macaddr_addr_0 0x21>;
+ nvmem-cell-names = "mac-address";
phy-mode = "rgmii-rxid";
phy-handle = <&phy4>;
rxdv-delay = <1>;
};
};
+