* - MikroTik RouterBOARD mAP L-2nD
* - MikroTik RouterBOARD 911-2Hn (911 Lite2)
* - MikroTik RouterBOARD 911-5Hn (911 Lite5)
+ * - MikroTik RouterBOARD 931-2nD (hAP mini)
* - MikroTik RouterBOARD 941L-2nD
* - MikroTik RouterBOARD 951Ui-2nD
* - MikroTik RouterBOARD 952Ui-5ac2nD
* - MikroTik RouterBOARD LHG 5nD
* - MikroTik RouterBOARD wAP2nD
* - MikroTik RouterBOARD wAP G-5HacT2HnDwAP (wAP AC)
+ * - MikroTik RouterBOARD wAP R-2nD
*
* Preliminary support for the following hardware
* - MikroTik RouterBOARD cAP2nD
* hardware as the mAP L-2nD. It is unknown if they share the same board
* identifier.
*
- * Copyright (C) 2017 Thibaut VARENE <varenet@parisc-linux.org>
+ * Copyright (C) 2017-2018 Thibaut VARENE <varenet@parisc-linux.org>
* Copyright (C) 2016 David Hutchison <dhutchison@bluemesh.net>
* Copyright (C) 2017 Ryan Mounce <ryan@mounce.com.au>
*
#define RB952_GPIO_POE_POWER 14
#define RB952_GPIO_POE_STATUS 12
#define RB952_GPIO_BTN_RESET 16
-#define RB952_GPIO_USB_POWER RBSPI_SSR_GPIO(RB952_SSR_BIT_USB_POWER)
+#define RB952_GPIO_USB_PWROFF RBSPI_SSR_GPIO(RB952_SSR_BIT_USB_POWER)
#define RB952_GPIO_LED_LAN1 RBSPI_SSR_GPIO(RB952_SSR_BIT_LED_LAN1)
#define RB952_GPIO_LED_LAN2 RBSPI_SSR_GPIO(RB952_SSR_BIT_LED_LAN2)
#define RB952_GPIO_LED_LAN3 RBSPI_SSR_GPIO(RB952_SSR_BIT_LED_LAN3)
/* RB 962UiGS-5HacT2HnT gpios */
+#define RB962_WIFI_LED_1 1
+#define RB962_WIFI_LED_2 2
#define RB962_GPIO_POE_STATUS 2
#define RB962_GPIO_POE_POWER 3
#define RB962_GPIO_LED_USER 12
-#define RB962_GPIO_USB_POWER 13
+#define RB962_GPIO_USB_PWROFF 13
#define RB962_GPIO_BTN_RESET 20
static struct gpio_led rb962_leds_gpio[] __initdata = {
static struct mdio_board_info rb962_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
- .phy_addr = 0,
+ .mdio_addr = 0,
.platform_data = &rb962_ar8327_data,
},
};
#define RBMAP_GPIO_LED_POWER 4
#define RBMAP_GPIO_POE_POWER 14
#define RBMAP_GPIO_POE_STATUS 12
-#define RBMAP_GPIO_USB_POWER RBSPI_SSR_GPIO(RBMAP_SSR_BIT_USB_POWER)
+#define RBMAP_GPIO_USB_PWROFF RBSPI_SSR_GPIO(RBMAP_SSR_BIT_USB_POWER)
#define RBMAP_GPIO_LED_LAN1 RBSPI_SSR_GPIO(RBMAP_SSR_BIT_LED_LAN1)
#define RBMAP_GPIO_LED_LAN2 RBSPI_SSR_GPIO(RBMAP_SSR_BIT_LED_LAN2)
#define RBMAP_GPIO_LED_POEO RBSPI_SSR_GPIO(RBMAP_SSR_BIT_LED_POEO)
};
/* RB w APG-5HacT2HnD (wAP AC) gpios*/
-#define RBWAPGSC_LED1 1
-#define RBWAPGSC_LED2 8
-#define RBWAPGSC_LED3 9
-#define RBWAPGSC_POWERLED 16
+#define RBWAPGSC_WIFI_LED_1 1
+#define RBWAPGSC_WIFI_LED_2 8
+#define RBWAPGSC_WIFI_LED_3 9
+#define RBWAPGSC_GPIO_LED_POWER 16
#define RBWAPGSC_GPIO_BTN_RESET 1
#define RBWAPGSC_GPIO_MDIO_MDC 12
#define RBWAPGSC_GPIO_MDIO_DATA 11
static struct gpio_led rbwapgsc_leds[] __initdata = {
{
- .name = "rb:green:led1",
- .gpio = RBWAPGSC_LED1,
- .active_low = 1,
- },{
- .name = "rb:blue:power",
- .gpio = RBWAPGSC_POWERLED,
+ .name = "rb:green:power",
+ .gpio = RBWAPGSC_GPIO_LED_POWER,
.active_low = 1,
+ .default_state = LEDS_GPIO_DEFSTATE_ON,
},
};
#define RB911L_GPIO_LED_ETH 20
#define RB911L_GPIO_LED_POWER 11
#define RB911L_GPIO_LED_USER 3
-#define RB911L_GPIO_PIN_HOLE 14 /* for reference */
+#define RB911L_GPIO_PIN_HOLE 14 /* for reference, active low */
static struct gpio_led rb911l_leds[] __initdata = {
{
.name = "rb:green:power",
.gpio = RB911L_GPIO_LED_POWER,
.default_state = LEDS_GPIO_DEFSTATE_ON,
+ .active_low = 1,
.open_drain = 1,
}, {
.name = "rb:green:user",
},
};
+/* RB 931-2nD gpios */
+#define RB931_GPIO_BTN_RESET 0
+#define RB931_GPIO_BTN_MODE 9
+#define RB931_GPIO_LED_USER 1
+
+static struct gpio_keys_button rb931_gpio_keys[] __initdata = {
+ {
+ .desc = "Reset button",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = RBSPI_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = RB931_GPIO_BTN_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "Mode button",
+ .type = EV_KEY,
+ .code = BTN_0,
+ .debounce_interval = RBSPI_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = RB931_GPIO_BTN_MODE,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_led rb931_leds[] __initdata = {
+ {
+ .name = "rb:green:user",
+ .gpio = RB931_GPIO_LED_USER,
+ .active_low = 1,
+ },
+};
+
+/* RB wAP R-2nD (wAP R) gpios*/
+#define RBWAPR_GPIO_LED_USER 14
+#define RBWAPR_GPIO_LED1 12
+#define RBWAPR_GPIO_LED2 13
+#define RBWAPR_GPIO_LED3 3
+#define RBWAPR_GPIO_PCIE_PWROFF 15
+#define RBWAPR_GPIO_CONTROL 10
+#define RBWAPR_GPIO_BTN_RESET 16
+
+static struct gpio_led rbwapr_leds[] __initdata = {
+ {
+ .name = "rb:green:user",
+ .gpio = RBWAPR_GPIO_LED_USER,
+ .active_low = 0,
+ },{
+ .name = "rb:green:led1",
+ .gpio = RBWAPR_GPIO_LED1,
+ .active_low = 1,
+ },{
+ .name = "rb:green:led2",
+ .gpio = RBWAPR_GPIO_LED2,
+ .active_low = 1,
+ },{
+ .name = "rb:green:led3",
+ .gpio = RBWAPR_GPIO_LED3,
+ .active_low = 0,
+ },
+};
+
+
static struct gen_74x164_chip_platform_data rbspi_ssr_data = {
.base = RBSPI_SSR_GPIO_BASE,
.num_registers = 1,
rbspi_network_setup(flags, 1, 5, 6);
if (flags & RBSPI_HAS_USB)
- gpio_request_one(RB952_GPIO_USB_POWER,
+ gpio_request_one(RB952_GPIO_USB_PWROFF, GPIOF_ACTIVE_LOW |
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
- "USB power");
+ "USB power off");
if (flags & RBSPI_HAS_POE)
gpio_request_one(RB952_GPIO_POE_POWER,
rbspi_wlan_init(1, 7);
if (flags & RBSPI_HAS_USB)
- gpio_request_one(RB962_GPIO_USB_POWER,
+ gpio_request_one(RB962_GPIO_USB_PWROFF, GPIOF_ACTIVE_LOW |
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
- "USB power");
+ "USB power off");
/* PoE output GPIO is inverted, set GPIOF_ACTIVE_LOW for consistency */
if (flags & RBSPI_HAS_POE)
GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
"POE power");
- /* USB power GPIO is inverted, set GPIOF_ACTIVE_LOW for consistency */
if (flags & RBSPI_HAS_USB)
- gpio_request_one(RBMAP_GPIO_USB_POWER,
+ gpio_request_one(RBMAP_GPIO_USB_PWROFF,
GPIOF_OUT_INIT_HIGH | GPIOF_ACTIVE_LOW |
GPIOF_EXPORT_DIR_FIXED,
- "USB power");
+ "USB power off");
ath79_register_leds_gpio(-1, ARRAY_SIZE(rbmap_leds), rbmap_leds);
ath79_register_leds_gpio(-1, ARRAY_SIZE(rb911l_leds), rb911l_leds);
}
+/*
+ * Init the hAP mini hardware (QCA953x).
+ * The 931-2nD (hAP mini) has 3 ethernet ports, with port 2-3
+ * being assigned to LAN on the casing, and port 1 being assigned
+ * to "internet" (WAN) on the casing. Port 1 is connected to PHY2.
+ * Since WAN is neither PHY0 nor PHY4, we cannot use GMAC0 with this device.
+ */
+static void __init rb931_setup(void)
+{
+ u32 flags = RBSPI_HAS_WLAN0;
+
+ if (!rbspi_platform_setup())
+ return;
+
+ rbspi_peripherals_setup(flags);
+
+ /* GMAC1 is HW MAC, WLAN0 MAC is HW MAC + 3 */
+ rbspi_network_setup(flags, 0, 3, 0);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(rb931_leds), rb931_leds);
+
+ /* hAP mini has two buttons */
+ ath79_register_gpio_keys_polled(-1, RBSPI_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(rb931_gpio_keys),
+ rb931_gpio_keys);
+}
+
+/*
+ * Init the wAP R hardware.
+ * The wAP R-2nD has a single ethernet port and a mini PCIe slot.
+ * The OEM source shows it has usb (used over PCIe for LTE devices),
+ * and the 'control' GPIO is assumed to be an output pin not tied to an LED.
+ */
+static void __init rbwapr_setup(void)
+{
+ u32 flags = RBSPI_HAS_WLAN0 | RBSPI_HAS_USB | RBSPI_HAS_PCI;
+
+ if (!rbspi_platform_setup())
+ return;
+
+ rbspi_peripherals_setup(flags);
+
+ /* GMAC1 is HW MAC, WLAN0 MAC is HW MAC + 1 */
+ rbspi_network_setup(flags, 0, 1, 0);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(rbwapr_leds), rbwapr_leds);
+
+ gpio_request_one(RBWAPR_GPIO_PCIE_PWROFF, GPIOF_OUT_INIT_HIGH |
+ GPIOF_ACTIVE_LOW | GPIOF_EXPORT_DIR_FIXED,
+ "PCIE power off");
+
+ gpio_request_one(RBWAPR_GPIO_CONTROL, GPIOF_OUT_INIT_LOW |
+ GPIOF_ACTIVE_LOW | GPIOF_EXPORT_DIR_FIXED,
+ "control");
+
+ rbspi_register_reset_button(RBWAPR_GPIO_BTN_RESET);
+}
+
MIPS_MACHINE_NONAME(ATH79_MACH_RB_MAPL, "map-hb", rbmapl_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_941, "H951L", rbhapl_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_911L, "911L", rb911l_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_750UPR2, "750-hb", rb750upr2_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_LHG5, "lhg", rblhg_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_WAP, "wap-hb", rbwap_setup);
+MIPS_MACHINE_NONAME(ATH79_MACH_RB_WAPR, "wap-lte", rbwapr_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_CAP, "cap-hb", rbcap_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_MAP, "map2-hb", rbmap_setup);
MIPS_MACHINE_NONAME(ATH79_MACH_RB_WAPAC, "wapg-sc", rbwapgsc_setup);
+MIPS_MACHINE_NONAME(ATH79_MACH_RB_931, "931", rb931_setup);
projects / openwrt / staging / jow.git / blobdiff