DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE define Device/FitImage KERNEL_SUFFIX := -uImage.itb KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb KERNEL_NAME := Image endef define Device/FitImageLzma KERNEL_SUFFIX := -uImage.itb KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb KERNEL_NAME := Image endef define Device/FitzImage KERNEL_SUFFIX := -zImage.itb KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb KERNEL_NAME := zImage endef define Device/UbiFit KERNEL_IN_UBI := 1 IMAGES := factory.ubi sysupgrade.bin IMAGE/factory.ubi := append-ubi IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef define Device/DniImage $(call Device/FitzImage) NETGEAR_BOARD_ID := NETGEAR_HW_ID := IMAGES += factory.img IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \ append-rootfs | pad-rootfs | check-size | append-metadata endef define Build/append-rootfshdr mkimage -A $(LINUX_KARCH) \ -O linux -T filesystem \ -C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ -n root.squashfs -d $(IMAGE_ROOTFS) $@.new cat $(IMAGE_KERNEL) > $@.$1 dd if=$@.new bs=64 count=1 >> $@.$1 endef define Build/append-rutx-metadata echo \ '{ \ "device_code": [".*"], \ "hwver": [".*"], \ "batch": [".*"], \ "serial": [".*"], \ "supported_devices":["teltonika,rutx"] \ }' | fwtool -I - $@ endef define Build/copy-file cat "$(1)" > "$@" endef define Build/mkmylofw_32m $(eval device_id=$(word 1,$(1))) $(eval revision=$(word 2,$(1))) let \ size="$$(stat -c%s $@)" \ pad="$(subst k,* 1024,$(BLOCKSIZE))" \ pad="(pad - (size % pad)) % pad" \ newsize='size + pad'; \ $(STAGING_DIR_HOST)/bin/mkmylofw \ -B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \ -s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \ $@.new @mv $@.new $@ endef define Build/wac5xx-netgear-tar mkdir $@.tmp mv $@ $@.tmp/wac5xx-ubifs-root.img md5sum $@.tmp/wac5xx-ubifs-root.img > $@.tmp/wac5xx-ubifs-root.md5sum echo "WAC505 WAC510" > $@.tmp/metadata.txt echo "WAC505_V9.9.9.9" > $@.tmp/version tar -C $@.tmp/ -cf $@ . rm -rf $@.tmp endef define Build/qsdk-ipq-factory-nand-askey $(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\ askey_kernel $@.$1 \ askey_fs $(IMAGE_ROOTFS) \ ubifs $@ PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new @mv $@.new $@ endef define Build/qsdk-ipq-app-gpt cp $@ $@.tmp 2>/dev/null || true ptgen -g -o $@.tmp -a 1 -l 1024 \ -t 0x2e -N 0:HLOS -r -p 32M \ -t 0x83 -N rootfs -r -p 128M \ -N rootfs_data -p 512M cat $@.tmp >> $@ rm $@.tmp endef define Build/SenaoFW -$(STAGING_DIR_HOST)/bin/mksenaofw \ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \ -c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \ -e $@ \ -o $@.new @cp $@.new $@ endef define Build/wrgg-image mkwrggimg -i $@ \ -o $@.new \ -d "$(WRGG_DEVNAME)" \ -s "$(WRGG_SIGNATURE)" \ -v "" -m "" -B "" mv $@.new $@ endef define Device/8dev_habanero-dvk $(call Device/FitImageLzma) DEVICE_VENDOR := 8devices DEVICE_MODEL := Habanero DVK IMAGE_SIZE := 30976k SOC := qcom-ipq4019 IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata endef TARGET_DEVICES += 8dev_habanero-dvk define Device/8dev_jalapeno-common $(call Device/FitImage) $(call Device/UbiFit) BLOCKSIZE := 128k PAGESIZE := 2048 SOC := qcom-ipq4018 endef define Device/8dev_jalapeno $(call Device/8dev_jalapeno-common) DEVICE_VENDOR := 8devices DEVICE_MODEL := Jalapeno endef TARGET_DEVICES += 8dev_jalapeno define Device/alfa-network_ap120c-ac $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := ALFA Network DEVICE_MODEL := AP120C-AC SOC := qcom-ipq4018 DEVICE_PACKAGES := kmod-usb-acm kmod-tpm-i2c-atmel BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 65536k IMAGES := factory.bin sysupgrade.bin IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand endef TARGET_DEVICES += alfa-network_ap120c-ac define Device/aruba_glenmorangie $(call Device/FitImageLzma) DEVICE_VENDOR := Aruba SOC := qcom-ipq4029 endef define Device/aruba_ap-303 $(call Device/aruba_glenmorangie) DEVICE_MODEL := AP-303 endef TARGET_DEVICES += aruba_ap-303 define Device/aruba_ap-303h $(call Device/aruba_glenmorangie) DEVICE_MODEL := AP-303H endef TARGET_DEVICES += aruba_ap-303h define Device/aruba_ap-365 $(call Device/aruba_glenmorangie) DEVICE_MODEL := AP-365 DEVICE_PACKAGES := kmod-hwmon-ad7418 endef TARGET_DEVICES += aruba_ap-365 define Device/asus_map-ac2200 $(call Device/FitImageLzma) DEVICE_VENDOR := ASUS DEVICE_MODEL := Lyra (MAP-AC2200) SOC := qcom-ipq4019 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k endef TARGET_DEVICES += asus_map-ac2200 # WARNING: this is an initramfs image that gets you half of the way there # you need to delete the jffs2 ubi volume and sysupgrade to the final image # to get a "trx" you can flash via web UI for ac42u/ac58u: # - change call Device/FitImageLzma to Device/FitImage # - add the following below UIMAGE_NAME # UIMAGE_MAGIC := 0x27051956 # IMAGES += factory.trx # IMAGE/factory.trx := copy-file $(KDIR)/tmp/$$(KERNEL_INITRAMFS_IMAGE) | uImage none define Device/asus_rt-ac42u $(call Device/FitImageLzma) DEVICE_VENDOR := ASUS DEVICE_MODEL := RT-AC42U DEVICE_ALT0_VENDOR := ASUS DEVICE_ALT0_MODEL := RT-ACRH17 DEVICE_ALT1_VENDOR := ASUS DEVICE_ALT1_MODEL := RT-AC2200 SOC := qcom-ipq4019 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 20439364 FILESYSTEMS := squashfs # RT-AC82U is nowhere to be found online # Rather, this device is a/k/a RT-AC42U # But we'll go with what the vendor firmware has... UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC82U') DEVICE_PACKAGES := ath10k-firmware-qca9984-ct kmod-usb-ledtrig-usbport endef TARGET_DEVICES += asus_rt-ac42u define Device/asus_rt-ac58u $(call Device/FitImageLzma) DEVICE_VENDOR := ASUS DEVICE_MODEL := RT-AC58U DEVICE_ALT0_VENDOR := ASUS DEVICE_ALT0_MODEL := RT-ACRH13 SOC := qcom-ipq4018 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 20439364 FILESYSTEMS := squashfs # Someone - in their infinite wisdom - decided to put the firmware # version in front of the image name \03\00\00\04 => Version 3.0.0.4 # Since u-boot works with strings we either need another fixup step # to add a version... or we are very careful not to add '\0' into that # string and call it a day.... Yeah, we do the latter! UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U') DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \ kmod-usb-ledtrig-usbport endef TARGET_DEVICES += asus_rt-ac58u define Device/avm_fritzbox-4040 $(call Device/FitImageLzma) DEVICE_VENDOR := AVM DEVICE_MODEL := FRITZ!Box 4040 SOC := qcom-ipq4018 BOARD_NAME := fritz4040 IMAGE_SIZE := 29056k UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin UBOOT_PARTITION_SIZE := 524288 IMAGES += eva.bin IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata DEVICE_PACKAGES := fritz-tffs fritz-caldata endef TARGET_DEVICES += avm_fritzbox-4040 define Device/avm_fritzbox-7530 $(call Device/FitImageLzma) DEVICE_VENDOR := AVM DEVICE_MODEL := FRITZ!Box 7530 DEVICE_ALT0_VENDOR := AVM DEVICE_ALT0_MODEL := FRITZ!Box 7520 SOC := qcom-ipq4019 DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ltq-vdsl-vr11-app endef TARGET_DEVICES += avm_fritzbox-7530 define Device/avm_fritzrepeater-1200 $(call Device/FitImageLzma) DEVICE_VENDOR := AVM DEVICE_MODEL := FRITZ!Repeater 1200 SOC := qcom-ipq4019 DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand endef TARGET_DEVICES += avm_fritzrepeater-1200 define Device/avm_fritzrepeater-3000 $(call Device/FitImageLzma) DEVICE_VENDOR := AVM DEVICE_MODEL := FRITZ!Repeater 3000 SOC := qcom-ipq4019 DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand endef TARGET_DEVICES += avm_fritzrepeater-3000 define Device/buffalo_wtr-m2133hp $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Buffalo DEVICE_MODEL := WTR-M2133HP SOC := qcom-ipq4019 DEVICE_PACKAGES := ath10k-firmware-qca9984-ct BLOCKSIZE := 128k PAGESIZE := 2048 endef TARGET_DEVICES += buffalo_wtr-m2133hp define Device/cellc_rtl30vw KERNEL_SUFFIX := -zImage.itb KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb KERNEL = kernel-bin | fit none $$(KDIR)/image-$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048 KERNEL_NAME := zImage KERNEL_IN_UBI := IMAGES := factory.bin sysupgrade.bin IMAGE/factory.bin := append-rootfshdr kernel | append-ubi | qsdk-ipq-factory-nand-askey kernel IMAGE/sysupgrade.bin := append-rootfshdr kernel | sysupgrade-tar kernel=$$$$@.kernel | append-metadata DEVICE_VENDOR := Cell C DEVICE_MODEL := RTL30VW SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@5 KERNEL_INSTALL := 1 KERNEL_SIZE := 4096k IMAGE_SIZE := 57344k BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi endef TARGET_DEVICES += cellc_rtl30vw define Device/cilab_meshpoint-one $(call Device/8dev_jalapeno-common) DEVICE_VENDOR := Crisis Innovation Lab DEVICE_MODEL := MeshPoint.One DEVICE_PACKAGES += kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127 endef # Missing DSA Setup #TARGET_DEVICES += cilab_meshpoint-one define Device/compex_wpj419 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Compex DEVICE_MODEL := WPJ419 SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@12 KERNEL_INSTALL := 1 BLOCKSIZE := 128k PAGESIZE := 2048 FILESYSTEMS := squashfs endef # Missing DSA Setup #TARGET_DEVICES += compex_wpj419 define Device/compex_wpj428 $(call Device/FitImage) DEVICE_VENDOR := Compex DEVICE_MODEL := WPJ428 SOC := qcom-ipq4028 DEVICE_DTS_CONFIG := config@4 BLOCKSIZE := 64k IMAGE_SIZE := 31232k KERNEL_SIZE := 4096k IMAGES += cpximg-6a04.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3 DEVICE_PACKAGES := kmod-gpio-beeper DEFAULT := n endef TARGET_DEVICES += compex_wpj428 define Device/devolo_magic-2-wifi-next $(call Device/FitImage) DEVICE_VENDOR := devolo DEVICE_MODEL := Magic 2 WiFi next SOC := qcom-ipq4018 KERNEL_SIZE := 4096k # If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image # it will bootm it, just like we want for the initramfs. KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to 64k |\ append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00' IMAGE_SIZE := 26624k IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEFAULT := n endef # Missing DSA Setup #TARGET_DEVICES += devolo_magic-2-wifi-next define Device/dlink_dap-2610 $(call Device/FitImageLzma) DEVICE_VENDOR := D-Link DEVICE_MODEL := DAP-2610 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@ap.dk01.1-c1 BLOCKSIZE := 64k WRGG_DEVNAME := /dev/mtdblock/8 WRGG_SIGNATURE := wapac30_dkbs_dap2610 IMAGE_SIZE := 14080k IMAGES += factory.bin # Bootloader expects a special 160 byte header which is added by # wrgg-image. # Factory image size must be larger than 6MB, and size in wrgg header must # match actual factory image size to be flashable from D-Link http server. # Bootloader verifies checksum of wrgg image before booting, thus jffs2 # cannot be part of the wrgg image. This is solved in the factory image by # having the rootfs at the end of the image (without pad-rootfs). And in # the sysupgrade image only the kernel is included in the wrgg checksum, # but this is not flashable from the D-link http server. # append-rootfs must start on an erase block boundary. IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata endef TARGET_DEVICES += dlink_dap-2610 define Device/edgecore_ecw5211 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Edgecore DEVICE_MODEL := ECW5211 SOC := qcom-ipq4018 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 DEVICE_PACKAGES := kmod-tpm-i2c-atmel kmod-usb-acm endef TARGET_DEVICES += edgecore_ecw5211 define Device/edgecore_oap100 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Edgecore DEVICE_MODEL := OAP100 SOC := qcom-ipq4019 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGES := sysupgrade.bin DEVICE_DTS_CONFIG := config@ap.dk07.1-c1 DEVICE_PACKAGES := kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi endef # Missing DSA Setup #TARGET_DEVICES += edgecore_oap100 define Device/engenius_eap1300 $(call Device/FitImage) DEVICE_VENDOR := EnGenius DEVICE_MODEL := EAP1300 DEVICE_DTS_CONFIG := config@4 BOARD_NAME := eap1300 SOC := qcom-ipq4018 KERNEL_SIZE := 5120k IMAGE_SIZE := 25344k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata endef # Missing DSA Setup #TARGET_DEVICES += engenius_eap1300 define Device/engenius_eap2200 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := EnGenius DEVICE_MODEL := EAP2200 SOC := qcom-ipq4019 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers endef # Missing DSA Setup #TARGET_DEVICES += engenius_eap2200 define Device/engenius_emd1 $(call Device/FitImage) DEVICE_VENDOR := EnGenius DEVICE_MODEL := EMD1 DEVICE_DTS_CONFIG := config@4 SOC := qcom-ipq4018 IMAGE_SIZE := 30720k IMAGES += factory.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size endef # Missing DSA Setup #TARGET_DEVICES += engenius_emd1 define Device/engenius_emr3500 $(call Device/FitImage) DEVICE_VENDOR := EnGenius DEVICE_MODEL := EMR3500 DEVICE_DTS_CONFIG := config@4 SOC := qcom-ipq4018 KERNEL_SIZE := 4096k IMAGE_SIZE := 30720k IMAGES += factory.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size DEFAULT := n endef # Missing DSA Setup #TARGET_DEVICES += engenius_emr3500 define Device/engenius_ens620ext $(call Device/FitImage) DEVICE_VENDOR := EnGenius DEVICE_MODEL := ENS620EXT SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@4 BLOCKSIZE := 64k PAGESIZE := 256 BOARD_NAME := ENS620EXT VENDOR_ID := 0x0101 PRODUCT_ID := 0x79 PRODUCT_ID_NEW := 0xA4 DATECODE := 190507 FW_VER := 3.1.2 FW_VER_NEW := 3.5.6 CW_VER := 1.8.99 IMAGE_SIZE := 21312k KERNEL_SIZE := 5120k FILESYSTEMS := squashfs IMAGES += factory_30.bin factory_35.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER) IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW) endef # Missing DSA Setup #TARGET_DEVICES += engenius_ens620ext define Device/extreme-networks_ws-ap3915i $(call Device/FitImage) DEVICE_VENDOR := Extreme Networks DEVICE_MODEL := WS-AP3915i IMAGE_SIZE := 30080k SOC := qcom-ipq4029 BLOCKSIZE := 128k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata endef TARGET_DEVICES += extreme-networks_ws-ap3915i define Device/ezviz_cs-w3-wd1200g-eup $(call Device/FitImage) DEVICE_VENDOR := EZVIZ DEVICE_MODEL := CS-W3-WD1200G DEVICE_VARIANT := EUP IMAGE_SIZE := 14848k KERNEL_SIZE = 6m SOC := qcom-ipq4018 IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \ append-metadata DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers DEVICE_COMPAT_VERSION := 2.0 DEVICE_COMPAT_MESSAGE := uboot's bootcmd has to be updated (see wiki). \ Upgrade via sysupgrade mechanism is not possible. endef TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup define Device/glinet_gl-a1300 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-A1300 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 131072k endef TARGET_DEVICES += glinet_gl-a1300 define Device/glinet_gl-ap1300 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-AP1300 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 131072k KERNEL_INSTALL := 1 DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi endef TARGET_DEVICES += glinet_gl-ap1300 define Device/glinet_gl-b1300 $(call Device/FitzImage) DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-B1300 BOARD_NAME := gl-b1300 SOC := qcom-ipq4029 KERNEL_SIZE := 4096k IMAGE_SIZE := 26624k IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += glinet_gl-b1300 define Device/glinet_gl-b2200 $(call Device/FitzImage) DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-B2200 SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@ap.dk04.1-c3 KERNEL_INITRAMFS_SUFFIX := -recovery.itb IMAGES := emmc.img.gz sysupgrade.bin IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\ pad-to 1024k | append-kernel |\ pad-to 33792k | append-rootfs |\ append-metadata | gzip IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata DEVICE_PACKAGES := ath10k-firmware-qca9888-ct \ kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs endef TARGET_DEVICES += glinet_gl-b2200 define Device/glinet_gl-s1300 $(call Device/FitzImage) DEVICE_VENDOR := GL.iNet DEVICE_MODEL := GL-S1300 SOC := qcom-ipq4029 KERNEL_SIZE := 4096k IMAGE_SIZE := 26624k IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := kmod-fs-ext4 kmod-mmc kmod-spi-dev endef # Missing DSA Setup #TARGET_DEVICES += glinet_gl-s1300 define Device/kernel-size-6350-8300 DEVICE_COMPAT_VERSION := 2.0 DEVICE_COMPAT_MESSAGE := Kernel partition size must be increased for \ this OpenWrt version. Before continuing, you MUST issue either the \ command "fw_setenv kernsize 500000" from the OpenWrt command line, \ or "setenv kernsize 500000 ; saveenv" from the U-Boot serial console. \ Instead of the sysupgrade image, you must then install the OpenWrt \ factory image, setting the force flag and wiping the configuration. \ (e.g. "sysupgrade -n -F openwrt-squashfs-factory.bin" on command line) endef define Device/linksys_ea6350v3 # The Linksys EA6350v3 has a uboot bootloader that does not # support either booting lzma kernel images nor booting UBI # partitions. This uboot, however, supports raw kernel images and # gzipped images. # # As configured by the OEM factory, the device will boot the kernel # from a fixed address with a fixed length of 3 MiB. Also, the # device has a hard-coded kernel command line that requires the # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively. # Oh... and the kernel partition overlaps with the rootfs # partition (the same for alt_kernel and alt_rootfs). # # If you are planing re-partitioning the device, you may want to # keep these details in mind: # 1. The kernel addresses you should honor are 0x00000000 and # 0x02800000 respectively. # 2. The kernel size (plus the dtb) cannot exceed 3 MiB in size # unless the uboot environment variable "kernsize" is increased. # 3. You can use 'zImage', but not a raw 'Image' packed with lzma. # 4. The kernel command line from uboot is harcoded to boot with # rootfs either in mtd11 or mtd13. $(call Device/FitzImage) $(call Device/kernel-size-6350-8300) DEVICE_VENDOR := Linksys DEVICE_MODEL := EA6350 DEVICE_VARIANT := v3 SOC := qcom-ipq4018 BLOCKSIZE := 128k PAGESIZE := 2048 KERNEL_SIZE := 5120k IMAGE_SIZE := 35840k UBINIZE_OPTS := -E 5 IMAGES += factory.bin IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3 endef TARGET_DEVICES += linksys_ea6350v3 define Device/linksys_ea8300 $(call Device/FitzImage) $(call Device/kernel-size-6350-8300) DEVICE_VENDOR := Linksys DEVICE_MODEL := EA8300 SOC := qcom-ipq4019 KERNEL_SIZE := 5120k IMAGE_SIZE := 84992k BLOCKSIZE := 128k PAGESIZE := 2048 UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF IMAGES += factory.bin IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport endef TARGET_DEVICES += linksys_ea8300 define Device/linksys_mr8300 $(call Device/FitzImage) $(call Device/kernel-size-6350-8300) DEVICE_VENDOR := Linksys DEVICE_MODEL := MR8300 SOC := qcom-ipq4019 KERNEL_SIZE := 5120k IMAGE_SIZE := 84992k BLOCKSIZE := 128k PAGESIZE := 2048 UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF IMAGES += factory.bin IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport endef TARGET_DEVICES += linksys_mr8300 define Device/linksys_whw03v2 $(call Device/FitzImage) DEVICE_VENDOR := Linksys DEVICE_MODEL := WHW03 DEVICE_VARIANT := V2 SOC := qcom-ipq4019 KERNEL_SIZE := 6144k IMAGE_SIZE := 158720k BLOCKSIZE := 128k PAGESIZE := 2048 UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF IMAGES += factory.bin IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW03v2 DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-leds-pca963x kmod-spi-dev kmod-bluetooth endef TARGET_DEVICES += linksys_whw03v2 define Device/linksys_whw01 $(call Device/FitzImage) DEVICE_VENDOR := Linksys DEVICE_MODEL := WHW01 KERNEL_SIZE := 6144k IMAGE_SIZE := 75776K SOC := qcom-ipq4018 BLOCKSIZE := 128k PAGESIZE := 2048 UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF IMAGES += factory.bin IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW01 DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x endef TARGET_DEVICES += linksys_whw01 define Device/luma_wrtq-329acn $(call Device/FitImage) DEVICE_VENDOR := Luma Home DEVICE_MODEL := WRTQ-329ACN SOC := qcom-ipq4018 DEVICE_PACKAGES := kmod-ath3k kmod-eeprom-at24 kmod-i2c-gpio IMAGE_SIZE := 76632k BLOCKSIZE := 128k PAGESIZE := 2048 endef TARGET_DEVICES += luma_wrtq-329acn define Device/meraki_mr33 $(call Device/FitImage) DEVICE_VENDOR := Cisco Meraki DEVICE_MODEL := MR33 SOC := qcom-ipq4029 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct DEFAULT := n endef TARGET_DEVICES += meraki_mr33 define Device/meraki_mr74 $(call Device/FitImage) DEVICE_VENDOR := Cisco Meraki DEVICE_MODEL := MR74 SOC := qcom-ipq4029 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct DEVICE_DTS_CONFIG := config@3 DEFAULT := n endef TARGET_DEVICES += meraki_mr74 define Device/mobipromo_cm520-79f $(call Device/FitzImage) $(call Device/UbiFit) DEVICE_VENDOR := MobiPromo DEVICE_MODEL := CM520-79F SOC := qcom-ipq4019 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := kmod-usb-ledtrig-usbport endef TARGET_DEVICES += mobipromo_cm520-79f define Device/netgear_ex61x0v2 $(call Device/DniImage) DEVICE_VENDOR := NETGEAR DEVICE_DTS_CONFIG := config@4 NETGEAR_BOARD_ID := EX6150v2series NETGEAR_HW_ID := 29765285+16+0+128+2x2 IMAGE_SIZE := 14400k SOC := qcom-ipq4018 endef define Device/netgear_ex6100v2 $(call Device/netgear_ex61x0v2) DEVICE_MODEL := EX6100 DEVICE_VARIANT := v2 endef TARGET_DEVICES += netgear_ex6100v2 define Device/netgear_ex6150v2 $(call Device/netgear_ex61x0v2) DEVICE_MODEL := EX6150 DEVICE_VARIANT := v2 endef TARGET_DEVICES += netgear_ex6150v2 define Device/netgear_orbi $(call Device/DniImage) SOC := qcom-ipq4019 DEVICE_VENDOR := NETGEAR IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \ append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \ append-rootfs | pad-rootfs | netgear-dni IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \ sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup endef define Device/netgear_rbx50 $(call Device/netgear_orbi) NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4 KERNEL_SIZE := 3932160 ROOTFS_SIZE := 32243712 IMAGE_SIZE := 36175872 endef define Device/netgear_rbr50 $(call Device/netgear_rbx50) DEVICE_MODEL := RBR50 DEVICE_VARIANT := v1 NETGEAR_BOARD_ID := RBR50 endef TARGET_DEVICES += netgear_rbr50 define Device/netgear_rbs50 $(call Device/netgear_rbx50) DEVICE_MODEL := RBS50 DEVICE_VARIANT := v1 NETGEAR_BOARD_ID := RBS50 endef TARGET_DEVICES += netgear_rbs50 define Device/netgear_srx60 $(call Device/netgear_orbi) NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4 KERNEL_SIZE := 3932160 ROOTFS_SIZE := 32243712 IMAGE_SIZE := 36175872 endef define Device/netgear_srr60 $(call Device/netgear_srx60) DEVICE_MODEL := SRR60 NETGEAR_BOARD_ID := SRR60 endef TARGET_DEVICES += netgear_srr60 define Device/netgear_srs60 $(call Device/netgear_srx60) DEVICE_MODEL := SRS60 NETGEAR_BOARD_ID := SRS60 endef TARGET_DEVICES += netgear_srs60 define Device/netgear_wac510 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Netgear DEVICE_MODEL := WAC510 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@5 BLOCKSIZE := 128k PAGESIZE := 2048 IMAGES += factory.tar IMAGE/factory.tar := append-ubi | wac5xx-netgear-tar DEVICE_PACKAGES := uboot-envtools endef TARGET_DEVICES += netgear_wac510 define Device/openmesh_a42 $(call Device/FitImageLzma) DEVICE_VENDOR := OpenMesh DEVICE_MODEL := A42 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@om.a42 BLOCKSIZE := 64k KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15616k IMAGES += factory.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata endef TARGET_DEVICES += openmesh_a42 define Device/openmesh_a62 $(call Device/FitImageLzma) DEVICE_VENDOR := OpenMesh DEVICE_MODEL := A62 SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@om.a62 BLOCKSIZE := 64k KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15552k IMAGES += factory.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := ath10k-firmware-qca9888-ct endef TARGET_DEVICES += openmesh_a62 define Device/p2w_r619ac $(call Device/FitzImage) $(call Device/UbiFit) DEVICE_VENDOR := P&W DEVICE_MODEL := R619AC SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@10 BLOCKSIZE := 128k PAGESIZE := 2048 endef define Device/p2w_r619ac-64m $(call Device/p2w_r619ac) DEVICE_VARIANT := 64M NAND IMAGES += factory.bin IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand endef TARGET_DEVICES += p2w_r619ac-64m define Device/p2w_r619ac-128m $(call Device/p2w_r619ac) DEVICE_VARIANT := 128M NAND endef TARGET_DEVICES += p2w_r619ac-128m define Device/pakedge_wr-1 $(call Device/FitImageLzma) DEVICE_VENDOR := Pakedge DEVICE_MODEL := WR-1 DEVICE_DTS_CONFIG := config@ap.dk01.1-c1 SOC := qcom-ipq4018 BLOCKSIZE := 64k IMAGE_SIZE := 31232k IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += pakedge_wr-1 define Device/plasmacloud_pa1200 $(call Device/FitImageLzma) DEVICE_VENDOR := Plasma Cloud DEVICE_MODEL := PA1200 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@pc.pa1200 BLOCKSIZE := 64k KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15616k IMAGES += factory.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata endef TARGET_DEVICES += plasmacloud_pa1200 define Device/plasmacloud_pa2200 $(call Device/FitImageLzma) DEVICE_VENDOR := Plasma Cloud DEVICE_MODEL := PA2200 SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@pc.pa2200 BLOCKSIZE := 64k KERNEL = kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15552k IMAGES += factory.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := ath10k-firmware-qca9888-ct endef TARGET_DEVICES += plasmacloud_pa2200 define Device/qcom_ap-dk01.1-c1 DEVICE_VENDOR := Qualcomm Atheros DEVICE_MODEL := AP-DK01.1 DEVICE_VARIANT := C1 BOARD_NAME := ap-dk01.1-c1 SOC := qcom-ipq4019 DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1 KERNEL_INSTALL := 1 KERNEL_SIZE := 4096k IMAGE_SIZE := 26624k $(call Device/FitImage) IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata DEFAULT := n endef TARGET_DEVICES += qcom_ap-dk01.1-c1 define Device/qcom_ap-dk04.1-c1 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Qualcomm Atheros DEVICE_MODEL := AP-DK04.1 DEVICE_VARIANT := C1 SOC := qcom-ipq4019 DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1 KERNEL_INSTALL := 1 KERNEL_SIZE := 4048k BLOCKSIZE := 128k PAGESIZE := 2048 BOARD_NAME := ap-dk04.1-c1 DEFAULT := n endef TARGET_DEVICES += qcom_ap-dk04.1-c1 define Device/qxwlan_e2600ac-c1 $(call Device/FitImage) DEVICE_VENDOR := Qxwlan DEVICE_MODEL := E2600AC DEVICE_VARIANT := C1 BOARD_NAME := e2600ac-c1 SOC := qcom-ipq4019 IMAGE_SIZE := 31232k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += qxwlan_e2600ac-c1 define Device/qxwlan_e2600ac-c2 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Qxwlan DEVICE_MODEL := E2600AC DEVICE_VARIANT := C2 SOC := qcom-ipq4019 KERNEL_INSTALL := 1 BLOCKSIZE := 128k PAGESIZE := 2048 endef TARGET_DEVICES += qxwlan_e2600ac-c2 define Device/sony_ncp-hg100-cellular $(call Device/FitImage) DEVICE_VENDOR := Sony DEVICE_MODEL := NCP-HG100/Cellular DEVICE_DTS_CONFIG := config@ap.dk04.1-c4 SOC := qcom-ipq4019 KERNEL_SIZE := 8192k IMAGE_SIZE := 128m DEVICE_PACKAGES := e2fsprogs kmod-fs-ext4 uqmi endef TARGET_DEVICES += sony_ncp-hg100-cellular define Device/teltonika_rutx10 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Teltonika DEVICE_MODEL := RUTX10 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@5 KERNEL_INSTALL := 1 BLOCKSIZE := 128k PAGESIZE := 2048 FILESYSTEMS := squashfs IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata DEVICE_PACKAGES := kmod-bluetooth endef # Missing DSA Setup #TARGET_DEVICES += teltonika_rutx10 define Device/teltonika_rutx50 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Teltonika DEVICE_MODEL := RUTX50 SOC := qcom-ipq4018 DEVICE_DTS_CONFIG := config@5 KERNEL_INSTALL := 1 BLOCKSIZE := 128k PAGESIZE := 2048 FILESYSTEMS := squashfs IMAGE/factory.ubi := append-ubi DEVICE_PACKAGES := ipq-wifi-teltonika_rutx kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi endef TARGET_DEVICES += teltonika_rutx50 define Device/tel_x1pro $(call Device/FitImage) DEVICE_VENDOR := Telco DEVICE_MODEL := X1 Pro SOC := qcom-ipq4019 KERNEL_SIZE := 4096k IMAGE_SIZE := 31232k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi DEFAULT := n endef # Missing DSA Setup #TARGET_DEVICES += tel_x1pro define Device/unielec_u4019-32m $(call Device/FitImage) DEVICE_VENDOR := Unielec DEVICE_MODEL := U4019 DEVICE_VARIANT := 32M BOARD_NAME := u4019-32m SOC := qcom-ipq4019 KERNEL_SIZE := 4096k IMAGE_SIZE := 31232k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEFAULT := n endef # Missing DSA Setup #TARGET_DEVICES += unielec_u4019-32m define Device/wallys_dr40x9 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_VENDOR := Wallys DEVICE_MODEL := DR40X9 SOC := qcom-ipq40x9 DEVICE_DTS_CONFIG := config@ap.dk07.1-c1 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9 endef TARGET_DEVICES += wallys_dr40x9 define Device/zte_mf18a $(call Device/FitImage) DEVICE_VENDOR := ZTE DEVICE_MODEL := MF18A SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@ap.dk04.1-c1 BLOCKSIZE := 128k PAGESIZE := 2048 KERNEL_IN_UBI := 1 DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct endef TARGET_DEVICES += zte_mf18a define Device/zte_mf28x_common $(call Device/FitzImage) DEVICE_VENDOR := ZTE SOC := qcom-ipq4019 DEVICE_DTS_CONFIG := config@ap.dk04.1-c1 BLOCKSIZE := 128k PAGESIZE := 2048 KERNEL_IN_UBI := 1 DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi endef define Device/zte_mf286d $(call Device/zte_mf28x_common) DEVICE_MODEL := MF286D endef TARGET_DEVICES += zte_mf286d define Device/zte_mf287plus $(call Device/zte_mf28x_common) DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 DEVICE_MODEL := MF287Plus DEVICE_ALT0_VENDOR := ZTE DEVICE_ALT0_MODEL := MF287 DEVICE_PACKAGES += ipq-wifi-zte_mf287plus SOC := qcom-ipq4018 # The recovery image is used to return back to stock (an initramfs-based image # that can be flashed to the device via sysupgrade # The factory image is used to install from the stock firmware by using an # exploit for the web interface IMAGES += factory.bin recovery.bin IMAGE/factory.bin := append-ubi IMAGE/recovery.bin := append-squashfs4-fakeroot | sysupgrade-tar kernel=$$$$(BIN_DIR)/openwrt-$$(BOARD)$$(if $$(SUBTARGET),-$$(SUBTARGET))-$$(DEVICE_NAME)-initramfs-zImage.itb rootfs=$$$$@ | append-metadata endef TARGET_DEVICES += zte_mf287plus define Device/zte_mf289f $(call Device/zte_mf28x_common) DEVICE_MODEL := MF289F DEVICE_PACKAGES += ipq-wifi-zte_mf289f ath10k-firmware-qca9984-ct endef TARGET_DEVICES += zte_mf289f define Device/zyxel_nbg6617 $(call Device/FitImageLzma) DEVICE_VENDOR := ZyXEL DEVICE_MODEL := NBG6617 SOC := qcom-ipq4018 KERNEL_SIZE := 4096k ROOTFS_SIZE := 24960k RAS_BOARD := NBG6617 RAS_ROOTFS_SIZE := 19840k RAS_VERSION := "$(VERSION_DIST) $(REVISION)" IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata IMAGES += factory.bin # The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is # at least as large as the one of the initial firmware image (not the current # one on the device). This only applies to the Web-UI, the bootlaoder ignores # this minimum-size. However, the larger image can be flashed both ways. IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := kmod-usb-ledtrig-usbport endef TARGET_DEVICES += zyxel_nbg6617 define Device/zyxel_wre6606 $(call Device/FitImage) DEVICE_VENDOR := ZyXEL DEVICE_MODEL := WRE6606 DEVICE_DTS_CONFIG := config@4 SOC := qcom-ipq4018 IMAGE_SIZE := 13184k IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers endef # Missing DSA Setup #TARGET_DEVICES += zyxel_wre6606