target/linux/ath79/dts/qca9533_mikrotik_routerboard-map-2nd.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca9533_mikrotik_routerboard-16m.dtsi"
   4
   5 / {
   6         compatible = "mikrotik,routerboard-map-2nd", "qca,qca9533";
   7         model = "MikroTik RouterBOARD mAP-2nD (mAP)";
   8
   9         aliases {
  10                 led-boot = &led_user;
  11                 led-failsafe = &led_user;
  12                 led-running = &led_user;
  13                 led-upgrade = &led_user;
  14         };
  15
  16         leds {
  17                 compatible = "gpio-leds";
  18
  19                 power {
  20                         label = "green:power";
  21                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  22                         default-state = "on";
  23                 };
  24
  25                 eth_1 {
  26                         label = "green:eth_1";
  27                         gpios = <&gpio_ext 0 GPIO_ACTIVE_LOW>;
  28                 };
  29
  30                 eth_2 {
  31                         label = "green:eth_2";
  32                         gpios = <&gpio_ext 1 GPIO_ACTIVE_LOW>;
  33                 };
  34
  35                 poe_out {
  36                         label = "red:poe_out";
  37                         gpios = <&gpio_ext 2 GPIO_ACTIVE_LOW>;
  38                 };
  39
  40                 led_user: user {
  41                         label = "green:user";
  42                         gpios = <&gpio_ext 3 GPIO_ACTIVE_LOW>;
  43                 };
  44
  45                 wlan {
  46                         label = "green:wlan";
  47                         gpios = <&gpio_ext 4 GPIO_ACTIVE_LOW>;
  48                         linux,default-trigger = "phy0tpt";
  49                 };
  50
  51                 ap_cap {
  52                         label = "green:ap_cap";
  53                         gpios = <&gpio_ext 6 GPIO_ACTIVE_LOW>;
  54                 };
  55
  56         };
  57
  58         gpio-export {
  59                 compatible = "gpio-export";
  60
  61                 usb_power {
  62                         gpio-export,name = "usb-power";
  63                         gpio-export,output = <1>;
  64                         gpios = <&gpio_ext 5 GPIO_ACTIVE_LOW>;
  65                 };
  66
  67                 enable_poe_port5 {
  68                         gpio-export,name = "enable-poe";
  69                         gpio-export,output = <0>;
  70                         gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
  71                 };
  72         };
  73 };
  74
  75 &spi {
  76         pinctrl-names = "default";
  77         pinctrl-0 = <&pin_spi_cs1>;
  78
  79         gpio_ext: gpio_ext@1 {
  80                 compatible = "fairchild,74hc595";
  81                 reg = <1>;
  82                 gpio-controller;
  83                 #gpio-cells = <2>;
  84                 registers-number = <1>;
  85                 spi-max-frequency = <25000000>;
  86         };
  87 };
  88
  89
  90 &pinmux {
  91         pin_spi_cs1: pinmux_spi_cs1 {
  92                 pinctrl-single,bits = <0x8 0x0a000000 0xff000000>;
  93         };
  94 };
  95
  96 &wmac {
  97         status = "okay";
  98
  99         qca,no-eeprom;
 100 };
 101
 102 &eth0 {
 103         status = "okay";
 104
 105         phy-handle = <&swphy0>;
 106
 107         gmac-config {
 108                 device = <&gmac>;
 109                 switch-phy-swap = <1>;
 110         };
 111 };
 112
 113 &usb0 {
 114         status = "okay";
 115 };
 116
 117 &usb_phy {
 118         status = "okay";
 119 };