target/linux/ath79/dts/qca9531_glinet_gl-x750.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca953x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "glinet,gl-x750", "qca,qca9531";
  10         model = "GL.iNet GL-X750";
  11
  12         keys {
  13                 compatible = "gpio-keys";
  14
  15                 pinctrl-names = "default";
  16                 pinctrl-0 = <&jtag_disable_pins>;
  17
  18                 reset {
  19                         label = "reset";
  20                         linux,code = <KEY_RESTART>;
  21                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  22                 };
  23         };
  24
  25         leds {
  26                 compatible = "gpio-leds";
  27
  28                 power {
  29                         label = "green:power";
  30                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  31                         default-state = "on";
  32                 };
  33
  34                 wlan2g {
  35                         label = "green:wlan2g";
  36                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  37                         linux,default-trigger = "phy1tpt";
  38                 };
  39
  40                 wlan5g {
  41                         label = "green:wlan5g";
  42                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  43                         linux,default-trigger = "phy0tpt";
  44                 };
  45
  46                 wan {
  47                         label = "green:wan";
  48                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  49                 };
  50
  51                 4g {
  52                         label = "green:4g";
  53                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  54                 };
  55         };
  56 };
  57
  58 &pcie0 {
  59         status = "okay";
  60 };
  61
  62 &usb0 {
  63         status = "okay";
  64 };
  65
  66 &usb_phy {
  67         status = "okay";
  68 };
  69
  70 &spi {
  71         status = "okay";
  72
  73         flash@0 {
  74                 compatible = "jedec,spi-nor";
  75                 reg = <0>;
  76                 spi-max-frequency = <25000000>;
  77
  78                 partitions {
  79                         compatible = "fixed-partitions";
  80                         #address-cells = <1>;
  81                         #size-cells = <1>;
  82
  83                         partition@0 {
  84                                 label = "u-boot";
  85                                 reg = <0x000000 0x040000>;
  86                                 read-only;
  87                         };
  88
  89                         partition@40000 {
  90                                 label = "u-boot-env";
  91                                 reg = <0x040000 0x010000>;
  92                         };
  93
  94                         art: partition@50000 {
  95                                 label = "art";
  96                                 reg = <0x050000 0x010000>;
  97                                 read-only;
  98
  99                                 nvmem-layout {
 100                                         compatible = "fixed-layout";
 101                                         #address-cells = <1>;
 102                                         #size-cells = <1>;
 103
 104                                         macaddr_art_0: macaddr@0 {
 105                                                 reg = <0x0 0x6>;
 106                                         };
 107                                 };
 108                         };
 109
 110                         partition@60000 {
 111                                 compatible = "denx,uimage";
 112                                 label = "firmware";
 113                                 reg = <0x060000 0xfa0000>;
 114                         };
 115                 };
 116         };
 117 };
 118
 119 &eth0 {
 120         status = "okay";
 121
 122         phy-handle = <&swphy4>;
 123
 124         nvmem-cells = <&macaddr_art_0>;
 125         nvmem-cell-names = "mac-address";
 126 };
 127
 128 &eth1 {
 129         nvmem-cells = <&macaddr_art_0>;
 130         nvmem-cell-names = "mac-address";
 131         mac-address-increment = <1>;
 132 };
 133
 134 &wmac {
 135         status = "okay";
 136
 137         mtd-cal-data = <&art 0x1000>;
 138 };