target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca953x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "glinet,gl-ar750", "qca,qca9531";
  10         model = "GL.iNet GL-AR750";
  11
  12         aliases {
  13                 led-boot = &led_power;
  14                 led-failsafe = &led_power;
  15                 led-running = &led_power;
  16                 led-upgrade = &led_power;
  17                 label-mac-device = &eth0;
  18         };
  19
  20         keys {
  21                 compatible = "gpio-keys";
  22
  23                 pinctrl-names = "default";
  24                 pinctrl-0 = <&jtag_disable_pins>;
  25
  26                 reset {
  27                         label = "reset";
  28                         linux,code = <KEY_RESTART>;
  29                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  30                 };
  31
  32                 mode {
  33                         label = "mode";
  34                         linux,code = <BTN_0>;
  35                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  36                 };
  37         };
  38
  39         leds {
  40                 compatible = "gpio-leds";
  41
  42                 led_power: power {
  43                         label = "white:power";
  44                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  45                         default-state = "on";
  46                 };
  47
  48                 wlan2g {
  49                         label = "white:wlan2g";
  50                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  51                         linux,default-trigger = "phy1tpt";
  52                 };
  53
  54                 wlan5g {
  55                         label = "white:wlan5g";
  56                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  57                         linux,default-trigger = "phy0tpt";
  58                 };
  59         };
  60
  61         i2c {
  62                 compatible = "i2c-gpio";
  63
  64                 sda-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  65                 scl-gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  66         };
  67 };
  68
  69 &pcie0 {
  70         status = "okay";
  71
  72         wifi@0,0 {
  73                 compatible = "qcom,ath10k";
  74                 reg = <0 0 0 0 0>;
  75                 device_type = "pci";
  76         };
  77 };
  78
  79 &uart {
  80         status = "okay";
  81 };
  82
  83 &usb0 {
  84         status = "okay";
  85 };
  86
  87 &usb_phy {
  88         status = "okay";
  89 };
  90
  91 &spi {
  92         status = "okay";
  93         num-cs = <0>;
  94
  95         flash@0 {
  96                 compatible = "jedec,spi-nor";
  97                 reg = <0>;
  98                 spi-max-frequency = <25000000>;
  99
 100                 partitions {
 101                         compatible = "fixed-partitions";
 102                         #address-cells = <1>;
 103                         #size-cells = <1>;
 104
 105                         partition@0 {
 106                                 label = "u-boot";
 107                                 reg = <0x000000 0x040000>;
 108                                 read-only;
 109                         };
 110
 111                         partition@40000 {
 112                                 label = "u-boot-env";
 113                                 reg = <0x040000 0x010000>;
 114                                 read-only;
 115                         };
 116
 117                         art: partition@50000 {
 118                                 label = "art";
 119                                 reg = <0x050000 0x010000>;
 120                                 read-only;
 121                         };
 122
 123                         partition@60000 {
 124                                 compatible = "denx,uimage";
 125                                 label = "firmware";
 126                                 reg = <0x060000 0xfa0000>;
 127                         };
 128                 };
 129         };
 130 };
 131
 132 &eth0 {
 133         status = "okay";
 134
 135         phy-handle = <&swphy4>;
 136
 137         mtd-mac-address = <&art 0x0>;
 138 };
 139
 140 &eth1 {
 141         mtd-mac-address = <&art 0x0>;
 142         mtd-mac-address-increment = <1>;
 143 };
 144
 145 &wmac {
 146         status = "okay";
 147
 148         mtd-cal-data = <&art 0x1000>;
 149 };