ath79: reorganize DTSI for ar7240 TP-Link devices
[openwrt/staging/yousong.git] / target / linux / ath79 / dts / ar7240_tplink.dtsi
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2
3 #include <dt-bindings/gpio/gpio.h>
4 #include <dt-bindings/input/input.h>
5
6 #include "ar7240.dtsi"
7
8 / {
9 aliases {
10 led-boot = &led_system;
11 led-failsafe = &led_system;
12 led-running = &led_system;
13 led-upgrade = &led_system;
14 };
15
16 keys {
17 compatible = "gpio-keys-polled";
18 poll-interval = <20>;
19
20 reset {
21 label = "reset";
22 linux,code = <KEY_RESTART>;
23 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
24 debounce-interval = <60>;
25 };
26
27 wps {
28 label = "wps";
29 linux,code = <KEY_WPS_BUTTON>;
30 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
31 debounce-interval = <60>;
32 };
33 };
34
35 leds: leds {
36 compatible = "gpio-leds";
37
38 pinctrl-names = "default";
39 pinctrl-0 = <&pinmux_switch_led_pins>;
40
41 led_system: system {
42 label = "tp-link:green:system";
43 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
44 };
45
46 qss {
47 label = "tp-link:green:qss";
48 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
49 };
50 };
51
52 ath9k-leds {
53 compatible = "gpio-leds";
54
55 wlan {
56 label = "tp-link:green:wlan";
57 gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
58 linux,default-trigger = "phy0tpt";
59 };
60 };
61 };
62
63 &spi {
64 status = "okay";
65 num-cs = <1>;
66
67 flash@0 {
68 compatible = "jedec,spi-nor";
69 reg = <0>;
70 spi-max-frequency = <25000000>;
71
72 partitions {
73 compatible = "fixed-partitions";
74 #address-cells = <1>;
75 #size-cells = <1>;
76
77 uboot: partition@0 {
78 reg = <0x0 0x20000>;
79 label = "u-boot";
80 read-only;
81 };
82
83 partition@20000 {
84 compatible = "tplink,firmware";
85 reg = <0x20000 0x3d0000>;
86 label = "firmware";
87 };
88
89 art: partition@3f0000 {
90 reg = <0x3f0000 0x10000>;
91 label = "art";
92 read-only;
93 };
94 };
95 };
96 };
97
98 &eth1 {
99 status = "okay";
100 };
101
102 &pcie {
103 status = "okay";
104
105 ath9k: wifi@0,0 {
106 reg = <0x0000 0 0 0 0>;
107 qca,no-eeprom;
108 mtd-mac-address = <&uboot 0x1fc00>;
109 #gpio-cells = <2>;
110 gpio-controller;
111 };
112 };
113
114 &pinmux {
115 pinmux_switch_led_pins: switch_led_pins {
116 pinctrl-single,bits = <0x0 0x0 0xf8>;
117 };
118 };
119
120 &uart {
121 status = "okay";
122 };