arch/arm/dts/rk3399-gru.dtsi

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Google Gru (and derivatives) board device tree source
   4  *
   5  * Copyright 2016-2017 Google, Inc
   6  */
   7
   8 #include <dt-bindings/input/input.h>
   9 #include "rk3399.dtsi"
  10 #include "rk3399-op1-opp.dtsi"
  11
  12 / {
  13         chosen {
  14                 u-boot,dm-pre-reloc;
  15                 stdout-path = "serial2:115200n8";
  16                 u-boot,spl-boot-order = &spi_flash;
  17         };
  18
  19         config {
  20                 u-boot,spl-payload-offset = <0x40000>;
  21         };
  22
  23         /*
  24          * Power Tree
  25          *
  26          * In general an attempt is made to include all rails called out by
  27          * the schematic as long as those rails interact in some way with
  28          * the AP.  AKA:
  29          * - Rails that only connect to the EC (or devices that the EC talks to)
  30          *   are not included.
  31          * - Rails _are_ included if the rails go to the AP even if the AP
  32          *   doesn't currently care about them / they are always on.  The idea
  33          *   here is that it makes it easier to map to the schematic or extend
  34          *   later.
  35          *
  36          * If two rails are substantially the same from the AP's point of
  37          * view, though, we won't create a full fixed regulator.  We'll just
  38          * put the child rail as an alias of the parent rail.  Sometimes rails
  39          * look the same to the AP because one of these is true:
  40          * - The EC controls the enable and the EC always enables a rail as
  41          *   long as the AP is running.
  42          * - The rails are actually connected to each other by a jumper and
  43          *   the distinction is just there to add clarity/flexibility to the
  44          *   schematic.
  45          */
  46
  47         ppvar_sys: ppvar-sys {
  48                 compatible = "regulator-fixed";
  49                 regulator-name = "ppvar_sys";
  50                 regulator-always-on;
  51                 regulator-boot-on;
  52         };
  53
  54         pp1200_lpddr: pp1200-lpddr {
  55                 compatible = "regulator-fixed";
  56                 regulator-name = "pp1200_lpddr";
  57
  58                 /* EC turns on w/ lpddr_pwr_en; always on for AP */
  59                 regulator-always-on;
  60                 regulator-boot-on;
  61                 regulator-min-microvolt = <1200000>;
  62                 regulator-max-microvolt = <1200000>;
  63
  64                 vin-supply = <&ppvar_sys>;
  65         };
  66
  67         pp1800: pp1800 {
  68                 compatible = "regulator-fixed";
  69                 regulator-name = "pp1800";
  70
  71                 /* Always on when ppvar_sys shows power good */
  72                 regulator-always-on;
  73                 regulator-boot-on;
  74                 regulator-min-microvolt = <1800000>;
  75                 regulator-max-microvolt = <1800000>;
  76
  77                 vin-supply = <&ppvar_sys>;
  78         };
  79
  80         pp3300: pp3300 {
  81                 compatible = "regulator-fixed";
  82                 regulator-name = "pp3300";
  83
  84                 /* Always on; plain and simple */
  85                 regulator-always-on;
  86                 regulator-boot-on;
  87                 regulator-min-microvolt = <3300000>;
  88                 regulator-max-microvolt = <3300000>;
  89
  90                 vin-supply = <&ppvar_sys>;
  91         };
  92
  93         pp5000: pp5000 {
  94                 compatible = "regulator-fixed";
  95                 regulator-name = "pp5000";
  96
  97                 /* EC turns on w/ pp5000_en; always on for AP */
  98                 regulator-always-on;
  99                 regulator-boot-on;
 100                 regulator-min-microvolt = <5000000>;
 101                 regulator-max-microvolt = <5000000>;
 102
 103                 vin-supply = <&ppvar_sys>;
 104         };
 105
 106         ppvar_bigcpu_pwm: ppvar-bigcpu-pwm {
 107                 compatible = "pwm-regulator";
 108                 regulator-name = "ppvar_bigcpu_pwm";
 109
 110                 pwms = <&pwm1 0 3337 0>;
 111                 pwm-supply = <&ppvar_sys>;
 112                 pwm-dutycycle-range = <100 0>;
 113                 pwm-dutycycle-unit = <100>;
 114
 115                 /* EC turns on w/ ap_core_en; always on for AP */
 116                 regulator-always-on;
 117                 regulator-boot-on;
 118                 regulator-min-microvolt = <800107>;
 119                 regulator-max-microvolt = <1302232>;
 120         };
 121
 122         ppvar_bigcpu: ppvar-bigcpu {
 123                 compatible = "vctrl-regulator";
 124                 regulator-name = "ppvar_bigcpu";
 125
 126                 regulator-min-microvolt = <800107>;
 127                 regulator-max-microvolt = <1302232>;
 128
 129                 ctrl-supply = <&ppvar_bigcpu_pwm>;
 130                 ctrl-voltage-range = <800107 1302232>;
 131
 132                 regulator-settling-time-up-us = <322>;
 133         };
 134
 135         ppvar_litcpu_pwm: ppvar-litcpu-pwm {
 136                 compatible = "pwm-regulator";
 137                 regulator-name = "ppvar_litcpu_pwm";
 138
 139                 pwms = <&pwm2 0 3337 0>;
 140                 pwm-supply = <&ppvar_sys>;
 141                 pwm-dutycycle-range = <100 0>;
 142                 pwm-dutycycle-unit = <100>;
 143
 144                 /* EC turns on w/ ap_core_en; always on for AP */
 145                 regulator-always-on;
 146                 regulator-boot-on;
 147                 regulator-min-microvolt = <797743>;
 148                 regulator-max-microvolt = <1307837>;
 149         };
 150
 151         ppvar_litcpu: ppvar-litcpu {
 152                 compatible = "vctrl-regulator";
 153                 regulator-name = "ppvar_litcpu";
 154
 155                 regulator-min-microvolt = <797743>;
 156                 regulator-max-microvolt = <1307837>;
 157
 158                 ctrl-supply = <&ppvar_litcpu_pwm>;
 159                 ctrl-voltage-range = <797743 1307837>;
 160
 161                 regulator-settling-time-up-us = <384>;
 162         };
 163
 164         ppvar_gpu_pwm: ppvar-gpu-pwm {
 165                 compatible = "pwm-regulator";
 166                 regulator-name = "ppvar_gpu_pwm";
 167
 168                 pwms = <&pwm0 0 3337 0>;
 169                 pwm-supply = <&ppvar_sys>;
 170                 pwm-dutycycle-range = <100 0>;
 171                 pwm-dutycycle-unit = <100>;
 172
 173                 /* EC turns on w/ ap_core_en; always on for AP */
 174                 regulator-always-on;
 175                 regulator-boot-on;
 176                 regulator-min-microvolt = <786384>;
 177                 regulator-max-microvolt = <1217747>;
 178         };
 179
 180         ppvar_gpu: ppvar-gpu {
 181                 compatible = "vctrl-regulator";
 182                 regulator-name = "ppvar_gpu";
 183
 184                 regulator-min-microvolt = <786384>;
 185                 regulator-max-microvolt = <1217747>;
 186
 187                 ctrl-supply = <&ppvar_gpu_pwm>;
 188                 ctrl-voltage-range = <786384 1217747>;
 189
 190                 regulator-settling-time-up-us = <390>;
 191         };
 192
 193         /* EC turns on w/ pp900_ddrpll_en */
 194         pp900_ddrpll: pp900-ap {
 195         };
 196
 197         /* EC turns on w/ pp900_pll_en */
 198         pp900_pll: pp900-ap {
 199         };
 200
 201         /* EC turns on w/ pp900_pmu_en */
 202         pp900_pmu: pp900-ap {
 203         };
 204
 205         /* EC turns on w/ pp1800_s0_en_l */
 206         pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
 207         };
 208
 209         /* EC turns on w/ pp1800_avdd_en_l */
 210         pp1800_avdd: pp1800 {
 211         };
 212
 213         /* EC turns on w/ pp1800_lid_en_l */
 214         pp1800_lid: pp1800_mic: pp1800 {
 215         };
 216
 217         /* EC turns on w/ lpddr_pwr_en */
 218         pp1800_lpddr: pp1800 {
 219         };
 220
 221         /* EC turns on w/ pp1800_pmu_en_l */
 222         pp1800_pmu: pp1800 {
 223         };
 224
 225         /* EC turns on w/ pp1800_usb_en_l */
 226         pp1800_usb: pp1800 {
 227         };
 228
 229         pp3000_sd_slot: pp3000-sd-slot {
 230                 compatible = "regulator-fixed";
 231                 regulator-name = "pp3000_sd_slot";
 232                 pinctrl-names = "default";
 233                 pinctrl-0 = <&sd_slot_pwr_en>;
 234
 235                 enable-active-high;
 236                 gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
 237
 238                 vin-supply = <&pp3000>;
 239         };
 240
 241         /*
 242          * Technically, this is a small abuse of 'regulator-gpio'; this
 243          * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
 244          * always on though, so it is sufficient to simply control the mux
 245          * here.
 246          */
 247         ppvar_sd_card_io: ppvar-sd-card-io {
 248                 compatible = "regulator-gpio";
 249                 regulator-name = "ppvar_sd_card_io";
 250                 pinctrl-names = "default";
 251                 pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
 252
 253                 enable-active-high;
 254                 enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 255                 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
 256                 states = <1800000 0x1
 257                           3000000 0x0>;
 258
 259                 regulator-min-microvolt = <1800000>;
 260                 regulator-max-microvolt = <3000000>;
 261         };
 262
 263         /* EC turns on w/ pp3300_trackpad_en_l */
 264         pp3300_trackpad: pp3300-trackpad {
 265         };
 266
 267         /* EC turns on w/ usb_a_en */
 268         pp5000_usb_a_vbus: pp5000 {
 269         };
 270
 271         gpio_keys: gpio-keys {
 272                 compatible = "gpio-keys";
 273                 pinctrl-names = "default";
 274                 pinctrl-0 = <&bt_host_wake_l>;
 275
 276                 wake_on_bt: wake-on-bt {
 277                         label = "Wake-on-Bluetooth";
 278                         gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 279                         linux,code = <KEY_WAKEUP>;
 280                         wakeup-source;
 281                 };
 282         };
 283
 284         max98357a: max98357a {
 285                 compatible = "maxim,max98357a";
 286                 pinctrl-names = "default";
 287                 pinctrl-0 = <&sdmode_en>;
 288                 sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 289                 sdmode-delay = <2>;
 290                 #sound-dai-cells = <0>;
 291                 status = "okay";
 292         };
 293
 294         sound: sound {
 295                 compatible = "rockchip,rk3399-gru-sound";
 296                 rockchip,cpu = <&i2s0 &i2s2>;
 297         };
 298 };
 299
 300 &cdn_dp {
 301         status = "okay";
 302 };
 303
 304 /*
 305  * Set some suspend operating points to avoid OVP in suspend
 306  *
 307  * When we go into S3 ARM Trusted Firmware will transition our PWM regulators
 308  * from wherever they're at back to the "default" operating point (whatever
 309  * voltage we get when we set the PWM pins to "input").
 310  *
 311  * This quick transition under light load has the possibility to trigger the
 312  * regulator "over voltage protection" (OVP).
 313  *
 314  * To make extra certain that we don't hit this OVP at suspend time, we'll
 315  * transition to a voltage that's much closer to the default (~1.0 V) so that
 316  * there will not be a big jump.  Technically we only need to get within 200 mV
 317  * of the default voltage, but the speed here should be fast enough and we need
 318  * suspend/resume to be rock solid.
 319  */
 320
 321 &cluster0_opp {
 322         opp05 {
 323                 opp-suspend;
 324         };
 325 };
 326
 327 &cluster1_opp {
 328         opp06 {
 329                 opp-suspend;
 330         };
 331 };
 332
 333 &cpu_l0 {
 334         cpu-supply = <&ppvar_litcpu>;
 335 };
 336
 337 &cpu_l1 {
 338         cpu-supply = <&ppvar_litcpu>;
 339 };
 340
 341 &cpu_l2 {
 342         cpu-supply = <&ppvar_litcpu>;
 343 };
 344
 345 &cpu_l3 {
 346         cpu-supply = <&ppvar_litcpu>;
 347 };
 348
 349 &cpu_b0 {
 350         cpu-supply = <&ppvar_bigcpu>;
 351 };
 352
 353 &cpu_b1 {
 354         cpu-supply = <&ppvar_bigcpu>;
 355 };
 356
 357 &cru {
 358         assigned-clocks =
 359                 <&cru PLL_GPLL>, <&cru PLL_CPLL>,
 360                 <&cru PLL_NPLL>,
 361                 <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
 362                 <&cru PCLK_PERIHP>,
 363                 <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
 364                 <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
 365                 <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
 366                 <&cru ACLK_VIO>, <&cru ACLK_HDCP>,
 367                 <&cru ACLK_GIC_PRE>,
 368                 <&cru PCLK_DDR>;
 369         assigned-clock-rates =
 370                 <600000000>, <800000000>,
 371                 <1000000000>,
 372                 <150000000>, <75000000>,
 373                 <37500000>,
 374                 <100000000>, <100000000>,
 375                 <50000000>, <800000000>,
 376                 <100000000>, <50000000>,
 377                 <400000000>, <400000000>,
 378                 <200000000>,
 379                 <200000000>;
 380 };
 381
 382 &emmc_phy {
 383         status = "okay";
 384 };
 385
 386 &gpu {
 387         mali-supply = <&ppvar_gpu>;
 388         status = "okay";
 389 };
 390
 391 ap_i2c_ts: &i2c3 {
 392         status = "okay";
 393
 394         clock-frequency = <400000>;
 395
 396         /* These are relatively safe rise/fall times */
 397         i2c-scl-falling-time-ns = <50>;
 398         i2c-scl-rising-time-ns = <300>;
 399 };
 400
 401 ap_i2c_audio: &i2c8 {
 402         status = "okay";
 403
 404         clock-frequency = <400000>;
 405
 406         /* These are relatively safe rise/fall times */
 407         i2c-scl-falling-time-ns = <50>;
 408         i2c-scl-rising-time-ns = <300>;
 409
 410         codec: da7219@1a {
 411                 compatible = "dlg,da7219";
 412                 reg = <0x1a>;
 413                 interrupt-parent = <&gpio1>;
 414                 interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
 415                 clocks = <&cru SCLK_I2S_8CH_OUT>;
 416                 clock-names = "mclk";
 417                 dlg,micbias-lvl = <2600>;
 418                 dlg,mic-amp-in-sel = "diff";
 419                 pinctrl-names = "default";
 420                 pinctrl-0 = <&headset_int_l>;
 421                 VDD-supply = <&pp1800>;
 422                 VDDMIC-supply = <&pp3300>;
 423                 VDDIO-supply = <&pp1800>;
 424
 425                 da7219_aad {
 426                         dlg,adc-1bit-rpt = <1>;
 427                         dlg,btn-avg = <4>;
 428                         dlg,btn-cfg = <50>;
 429                         dlg,mic-det-thr = <500>;
 430                         dlg,jack-ins-deb = <20>;
 431                         dlg,jack-det-rate = "32ms_64ms";
 432                         dlg,jack-rem-deb = <1>;
 433
 434                         dlg,a-d-btn-thr = <0xa>;
 435                         dlg,d-b-btn-thr = <0x16>;
 436                         dlg,b-c-btn-thr = <0x21>;
 437                         dlg,c-mic-btn-thr = <0x3E>;
 438                 };
 439         };
 440 };
 441
 442 &i2s0 {
 443         status = "okay";
 444 };
 445
 446 &i2s2 {
 447         status = "okay";
 448 };
 449
 450 &io_domains {
 451         status = "okay";
 452
 453         audio-supply = <&pp1800_audio>;         /* APIO5_VDD;  3d 4a */
 454         bt656-supply = <&pp1800_ap_io>;         /* APIO2_VDD;  2a 2b */
 455         gpio1830-supply = <&pp3000_ap>;         /* APIO4_VDD;  4c 4d */
 456         sdmmc-supply = <&ppvar_sd_card_io>;     /* SDMMC0_VDD; 4b    */
 457 };
 458
 459 &pcie0 {
 460         status = "okay";
 461
 462         ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
 463         pinctrl-names = "default";
 464         pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
 465         vpcie3v3-supply = <&pp3300_wifi_bt>;
 466         vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
 467         vpcie0v9-supply = <&pp900_pcie>;
 468
 469         pci_rootport: pcie@0,0 {
 470                 reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
 471                 #address-cells = <3>;
 472                 #size-cells = <2>;
 473                 ranges;
 474         };
 475 };
 476
 477 &pcie_phy {
 478         status = "okay";
 479 };
 480
 481 &pmu_io_domains {
 482         status = "okay";
 483
 484         pmu1830-supply = <&pp1800_pmu>;         /* PMUIO2_VDD */
 485 };
 486
 487 &pwm0 {
 488         status = "okay";
 489 };
 490
 491 &pwm1 {
 492         status = "okay";
 493 };
 494
 495 &pwm2 {
 496         status = "okay";
 497 };
 498
 499 &pwm3 {
 500         status = "okay";
 501 };
 502
 503 &sdhci {
 504         /*
 505          * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
 506          * same (or nearly the same) performance for all eMMC that are intended
 507          * to be used.
 508          */
 509         assigned-clock-rates = <150000000>;
 510
 511         bus-width = <8>;
 512         mmc-hs400-1_8v;
 513         mmc-hs400-enhanced-strobe;
 514         non-removable;
 515         status = "okay";
 516 };
 517
 518 &sdmmc {
 519         status = "okay";
 520
 521         /*
 522          * Note: configure "sdmmc_cd" as card detect even though it's actually
 523          * hooked to ground.  Because we specified "cd-gpios" below dw_mmc
 524          * should be ignoring card detect anyway.  Specifying the pin as
 525          * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
 526          * turned on that the system will still make sure the port is
 527          * configured as SDMMC and not JTAG.
 528          */
 529         pinctrl-names = "default";
 530         pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
 531                      &sdmmc_bus4>;
 532
 533         bus-width = <4>;
 534         cap-mmc-highspeed;
 535         cap-sd-highspeed;
 536         cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 537         disable-wp;
 538         sd-uhs-sdr12;
 539         sd-uhs-sdr25;
 540         sd-uhs-sdr50;
 541         sd-uhs-sdr104;
 542         vmmc-supply = <&pp3000_sd_slot>;
 543         vqmmc-supply = <&ppvar_sd_card_io>;
 544 };
 545
 546 &spi1 {
 547         status = "okay";
 548
 549         pinctrl-names = "default", "sleep";
 550         pinctrl-1 = <&spi1_sleep>;
 551
 552         spi_flash: spiflash@0 {
 553                 u-boot,dm-pre-reloc;
 554                 compatible = "jedec,spi-nor";
 555                 reg = <0>;
 556
 557                 /* May run faster once verified. */
 558                 spi-max-frequency = <10000000>;
 559         };
 560 };
 561
 562 &spi2 {
 563         status = "okay";
 564 };
 565
 566 &spi5 {
 567         status = "okay";
 568         spi-activate-delay = <100>;
 569         spi-max-frequency = <3000000>;
 570         spi-deactivate-delay = <200>;
 571
 572         cros_ec: ec@0 {
 573                 compatible = "google,cros-ec-spi";
 574                 reg = <0>;
 575                 interrupt-parent = <&gpio0>;
 576                 interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 577                 ec-interrupt = <&gpio0 1 GPIO_ACTIVE_LOW>;
 578                 pinctrl-names = "default";
 579                 pinctrl-0 = <&ec_ap_int_l>;
 580                 spi-max-frequency = <3000000>;
 581
 582                 i2c_tunnel: i2c-tunnel {
 583                         compatible = "google,cros-ec-i2c-tunnel";
 584                         google,remote-bus = <4>;
 585                         #address-cells = <1>;
 586                         #size-cells = <0>;
 587                 };
 588
 589                 usbc_extcon0: extcon@0 {
 590                         compatible = "google,extcon-usbc-cros-ec";
 591                         google,usb-port-id = <0>;
 592
 593                         #extcon-cells = <0>;
 594                 };
 595         };
 596 };
 597
 598 &tsadc {
 599         status = "okay";
 600
 601         rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
 602         rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
 603 };
 604
 605 &tcphy0 {
 606         status = "okay";
 607         extcon = <&usbc_extcon0>;
 608 };
 609
 610 &u2phy0 {
 611         status = "okay";
 612 };
 613
 614 &u2phy0_host {
 615         status = "okay";
 616 };
 617
 618 &u2phy1_host {
 619         status = "okay";
 620 };
 621
 622 &u2phy0_otg {
 623         status = "okay";
 624 };
 625
 626 &u2phy1_otg {
 627         status = "okay";
 628 };
 629
 630 &uart2 {
 631         status = "okay";
 632         u-boot,dm-pre-reloc;
 633 };
 634
 635 &usb_host0_ohci {
 636         status = "okay";
 637 };
 638
 639 &usbdrd3_0 {
 640         status = "okay";
 641         extcon = <&usbc_extcon0>;
 642 };
 643
 644 &usbdrd_dwc3_0 {
 645         status = "okay";
 646         dr_mode = "host";
 647 };
 648
 649 &vopb {
 650         status = "okay";
 651 };
 652
 653 &vopb_mmu {
 654         status = "okay";
 655 };
 656
 657 &vopl {
 658         status = "okay";
 659 };
 660
 661 &vopl_mmu {
 662         status = "okay";
 663 };
 664
 665 #include <cros-ec-keyboard.dtsi>
 666 #include <cros-ec-sbs.dtsi>
 667
 668 &pinctrl {
 669         /*
 670          * pinctrl settings for pins that have no real owners.
 671          *
 672          * At the moment settings are identical for S0 and S3, but if we later
 673          * need to configure things differently for S3 we'll adjust here.
 674          */
 675         pinctrl-names = "default";
 676         pinctrl-0 = <
 677                 &ap_pwroff      /* AP will auto-assert this when in S3 */
 678                 &clk_32k        /* This pin is always 32k on gru boards */
 679         >;
 680
 681         pcfg_output_low: pcfg-output-low {
 682                 output-low;
 683         };
 684
 685         pcfg_output_high: pcfg-output-high {
 686                 output-high;
 687         };
 688
 689         pcfg_pull_none_8ma: pcfg-pull-none-8ma {
 690                 bias-disable;
 691                 drive-strength = <8>;
 692         };
 693
 694         backlight-enable {
 695                 bl_en: bl-en {
 696                         rockchip,pins = <1 17 RK_FUNC_GPIO &pcfg_pull_none>;
 697                 };
 698         };
 699
 700         cros-ec {
 701                 ec_ap_int_l: ec-ap-int-l {
 702                         rockchip,pins = <RK_GPIO0 1 RK_FUNC_GPIO &pcfg_pull_up>;
 703                 };
 704         };
 705
 706         discrete-regulators {
 707                 sd_io_pwr_en: sd-io-pwr-en {
 708                         rockchip,pins = <RK_GPIO2 2 RK_FUNC_GPIO
 709                                          &pcfg_pull_none>;
 710                 };
 711
 712                 sd_pwr_1800_sel: sd-pwr-1800-sel {
 713                         rockchip,pins = <RK_GPIO2 28 RK_FUNC_GPIO
 714                                          &pcfg_pull_none>;
 715                 };
 716
 717                 sd_slot_pwr_en: sd-slot-pwr-en {
 718                         rockchip,pins = <RK_GPIO4 29 RK_FUNC_GPIO
 719                                          &pcfg_pull_none>;
 720                 };
 721         };
 722
 723         codec {
 724                 /* Has external pullup */
 725                 headset_int_l: headset-int-l {
 726                         rockchip,pins = <1 23 RK_FUNC_GPIO &pcfg_pull_none>;
 727                 };
 728
 729                 mic_int: mic-int {
 730                         rockchip,pins = <1 13 RK_FUNC_GPIO &pcfg_pull_down>;
 731                 };
 732         };
 733
 734         max98357a {
 735                 sdmode_en: sdmode-en {
 736                         rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_down>;
 737                 };
 738         };
 739
 740         pcie {
 741                 pcie_clkreqn_cpm: pci-clkreqn-cpm {
 742                         /*
 743                          * Since our pcie doesn't support ClockPM(CPM), we want
 744                          * to hack this as gpio, so the EP could be able to
 745                          * de-assert it along and make ClockPM(CPM) work.
 746                          */
 747                         rockchip,pins = <2 26 RK_FUNC_GPIO &pcfg_pull_none>;
 748                 };
 749         };
 750
 751         sdmmc {
 752                 /*
 753                  * We run sdmmc at max speed; bump up drive strength.
 754                  * We also have external pulls, so disable the internal ones.
 755                  */
 756                 sdmmc_bus4: sdmmc-bus4 {
 757                         rockchip,pins =
 758                                 <4 8 RK_FUNC_1 &pcfg_pull_none_8ma>,
 759                                 <4 9 RK_FUNC_1 &pcfg_pull_none_8ma>,
 760                                 <4 10 RK_FUNC_1 &pcfg_pull_none_8ma>,
 761                                 <4 11 RK_FUNC_1 &pcfg_pull_none_8ma>;
 762                 };
 763
 764                 sdmmc_clk: sdmmc-clk {
 765                         rockchip,pins =
 766                                 <4 12 RK_FUNC_1 &pcfg_pull_none_8ma>;
 767                 };
 768
 769                 sdmmc_cmd: sdmmc-cmd {
 770                         rockchip,pins =
 771                                 <4 13 RK_FUNC_1 &pcfg_pull_none_8ma>;
 772                 };
 773
 774                 /*
 775                  * In our case the official card detect is hooked to ground
 776                  * to avoid getting access to JTAG just by sticking something
 777                  * in the SD card slot (see the force_jtag bit in the TRM).
 778                  *
 779                  * We still configure it as card detect because it doesn't
 780                  * hurt and dw_mmc will ignore it.  We make sure to disable
 781                  * the pull though so we don't burn needless power.
 782                  */
 783                 sdmmc_cd: sdmmc-cd {
 784                         rockchip,pins =
 785                                 <0 7 RK_FUNC_1 &pcfg_pull_none>;
 786                 };
 787
 788                 /* This is where we actually hook up CD; has external pull */
 789                 sdmmc_cd_gpio: sdmmc-cd-gpio {
 790                         rockchip,pins = <4 24 RK_FUNC_GPIO &pcfg_pull_none>;
 791                 };
 792         };
 793
 794         spi1 {
 795                 spi1_sleep: spi1-sleep {
 796                         /*
 797                          * Pull down SPI1 CLK/CS/RX/TX during suspend, to
 798                          * prevent leakage.
 799                          */
 800                         rockchip,pins = <1 9 RK_FUNC_GPIO &pcfg_pull_down>,
 801                                         <1 10 RK_FUNC_GPIO &pcfg_pull_down>,
 802                                         <1 7 RK_FUNC_GPIO &pcfg_pull_down>,
 803                                         <1 8 RK_FUNC_GPIO &pcfg_pull_down>;
 804                 };
 805         };
 806
 807         touchscreen {
 808                 touch_int_l: touch-int-l {
 809                         rockchip,pins = <3 13 RK_FUNC_GPIO &pcfg_pull_up>;
 810                 };
 811
 812                 touch_reset_l: touch-reset-l {
 813                         rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_pull_none>;
 814                 };
 815         };
 816
 817         trackpad {
 818                 ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
 819                         rockchip,pins = <3 12 RK_FUNC_GPIO &pcfg_output_high>;
 820                 };
 821
 822                 trackpad_int_l: trackpad-int-l {
 823                         rockchip,pins = <1 4 RK_FUNC_GPIO &pcfg_pull_up>;
 824                 };
 825         };
 826
 827         wifi: wifi {
 828                 wlan_module_reset_l: wlan-module-reset-l {
 829                         rockchip,pins = <1 11 RK_FUNC_GPIO &pcfg_pull_none>;
 830                 };
 831
 832                 bt_host_wake_l: bt-host-wake-l {
 833                         /* Kevin has an external pull up, but Gru does not */
 834                         rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>;
 835                 };
 836         };
 837
 838         write-protect {
 839                 ap_fw_wp: ap-fw-wp {
 840                         rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>;
 841                 };
 842         };
 843 };