openwrt/staging/mkresin.git
2 years agouboot-mvebu: remove enabled CONFIG_CMD_SETEXPR
Josef Schlehofer [Thu, 28 Apr 2022 13:50:20 +0000 (15:50 +0200)]
uboot-mvebu: remove enabled CONFIG_CMD_SETEXPR

We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.

It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.

[1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504

[2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7

[3] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/turris-omnia.bootscript#L2

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2 years agouboot-mvebu: add patch to enable setexpr for clearfog boards
Josef Schlehofer [Fri, 29 Apr 2022 15:52:29 +0000 (17:52 +0200)]
uboot-mvebu: add patch to enable setexpr for clearfog boards

Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
patch to U-boot mailing list to enable it.

It is required to use in OpenWrt bootscript for these boards [2].

[1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504

[2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2 years agoath79: add Netgear WNDAP360
Nick Hainke [Sun, 20 Mar 2022 16:57:22 +0000 (17:57 +0100)]
ath79: add Netgear WNDAP360

SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A

Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
   (9600,8N1)
   screen  /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.42
   saveenv
4. Reset the device
   reset
5. Hit again the spacebar
6. Now load the image via tftp:
   tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
   bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.

https://openwrt.org/toh/netgear/wndap360

The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:

&ath9k0 {
       nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
       nvmem-cell-names = "mac-address", "calibration";
};

&ath9k1 {
       nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
       nvmem-cell-names = "mac-address", "calibration";
};

&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};

cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};

Signed-off-by: Nick Hainke <vincent@systemli.org>
2 years agoath79: add USB power control for GL-AR300M series
PtilopsisLeucotis [Sat, 16 Apr 2022 10:21:58 +0000 (13:21 +0300)]
ath79: add USB power control for GL-AR300M series

Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.

Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
2 years agoath79: add support for TP-Link Deco M4R v1 and v2
Foica David [Thu, 21 Apr 2022 01:20:57 +0000 (04:20 +0300)]
ath79: add support for TP-Link Deco M4R v1 and v2

This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.

Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR

Flashing:

The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.

There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.

Pre-requisites:

- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
  as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.

Installation:

- Unplug your router and turn it upside down. Using a long and thin object
  like a SIM unlock tool, press and hold the reset button on the router and
  replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
  Choose the debug firmware that you downloaded and flash it. Wait until the
  router reboots (at this stage you can remove the static IP).

- Open a terminal window and connect to the router via telnet (the primary
  router should have a 192.168.0.1 IP address, secondary routers are
  different).
- Transfer the file over to the router, you can use curl to download it
  from the internet (use the insecure flag and make sure your source accepts
  insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
  separated. We can use dd to split the OpenWrt image file and flash it with
  mtd:

   dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
   dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256

- Once the images are ready, you have to flash the device using mtd
  (make sure to flash the correct partitions or you may be left with a
  hard bricked router):

   mtd write kernel.bin kernel
   mtd write rootfs.bin rootfs

- Flashing is done, reboot the device now.

Signed-off-by: Foica David <superh552@gmail.com>
2 years agoramips: add support for Wavlink WL-WN533A8
Davide Fioravanti [Mon, 18 Apr 2022 15:35:33 +0000 (17:35 +0200)]
ramips: add support for Wavlink WL-WN533A8

The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.

Hardware
--------
SoC:   Mediatek MT7621A
RAM:   128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
  - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
  - 1x MT7615NE (4x4:4) 5GHz
  - 8 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 3.0 port
UART:
  - 57600-8-N-1
    J4

Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)

Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
   WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
   WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
   WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)

   LABEL XX:XX:XX:XX:XX:65

   In OEM firmware the DBDC wifi interfaces have these mac addresses:
     2G) 82:XX:XX:XX:XX:65
     5G) 80:XX:XX:XX:XX:65

   While in OpenWrt the addresses are:
     2G) 80:XX:XX:XX:XX:65
     5G) 02:XX:XX:XX:XX:65

2) radio0 will show as 2G/5G interface but only 2G is really usable.

3) There is just one wifi led for all wifi interfaces.
   It currently shows only the radio0 GHz wifi activity.

4) My unit was shipped with M33A8.V5030.190716 firmware which contains
   the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
   the input box it will start the telnet daemon. Now you can access
   the telnet console on port 2323 with these credentials:
     username: admin2860
     password: admin

5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
   webcmd.shtml page. If your router is shipped with a previous firmware
   version and you want to back it up, you can follow the back up
   procedure of the WS-WN583A6.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2 years agoramips: create shared DTSI for Wavlink WN53XAX devices
Davide Fioravanti [Mon, 18 Apr 2022 14:54:40 +0000 (16:54 +0200)]
ramips: create shared DTSI for Wavlink WN53XAX devices

Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2 years agompc85xx: Fix output location of padded dtb
Martin Kennedy [Tue, 26 Apr 2022 21:04:06 +0000 (17:04 -0400)]
mpc85xx: Fix output location of padded dtb

In commit 7e614820a892 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.

Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.

Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.

This change fixes Github issue #9779 [1].

[1]: https://github.com/openwrt/openwrt/issues/9779

Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
2 years agobuild: don't remove BUILD_LOG_DIR in _clean
Huangbin Zhan [Sun, 24 Apr 2022 01:58:25 +0000 (09:58 +0800)]
build: don't remove BUILD_LOG_DIR in _clean

targetclean should not remove BUILD_LOG

Fixes: db34b93331e9 (add a version that can be bumped to force toolchain/target rebuild)
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2 years agokernel: 5.15: add missing symbol
Robert Marko [Sat, 30 Apr 2022 18:17:24 +0000 (20:17 +0200)]
kernel: 5.15: add missing symbol

CONFIG_QCOM_SPMI_ADC_TM5 gets uncovered while building IPQ40xx with 5.15.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2 years agokernel: bump 5.10 to 5.10.113
John Audia [Wed, 27 Apr 2022 18:14:45 +0000 (14:14 -0400)]
kernel: bump 5.10 to 5.10.113

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agomediatek: build ubnt-ledbar as a module
Chuanhong Guo [Sat, 30 Apr 2022 15:08:00 +0000 (23:08 +0800)]
mediatek: build ubnt-ledbar as a module

The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: mt7629: disable auxadc in kconfig
Chuanhong Guo [Sat, 30 Apr 2022 14:49:26 +0000 (22:49 +0800)]
mediatek: mt7629: disable auxadc in kconfig

manually edit kconfig to disable MT6577_AUXADC

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: mt7623: disable various input devices
Chuanhong Guo [Sat, 30 Apr 2022 14:35:27 +0000 (22:35 +0800)]
mediatek: mt7623: disable various input devices

Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: mt7622: add irq for spi-nor controller
Chuanhong Guo [Sat, 30 Apr 2022 12:24:07 +0000 (20:24 +0800)]
mediatek: mt7622: add irq for spi-nor controller

Save some CPU from unnecessary polling and make SPI flash reading
a tiny bit faster.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: remove left-overs from Linux 5.10
Daniel Golle [Sat, 30 Apr 2022 14:51:21 +0000 (15:51 +0100)]
mediatek: remove left-overs from Linux 5.10

Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.

Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: enable multi-core scheduling
Daniel Golle [Sat, 30 Apr 2022 14:48:58 +0000 (15:48 +0100)]
mediatek: enable multi-core scheduling

Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.

Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: refresh patches for Linux 5.15
Daniel Golle [Sat, 30 Apr 2022 14:17:46 +0000 (15:17 +0100)]
mediatek: refresh patches for Linux 5.15

Run `make target/linux/refresh` to align patches with OpenWrt style.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: backport recent DTS improvements for MT7622 SoC
Daniel Golle [Sat, 30 Apr 2022 14:41:13 +0000 (15:41 +0100)]
mediatek: backport recent DTS improvements for MT7622 SoC

Daniel Golle:
 190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch

Rui Salvaterra:
 191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch
 192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agokernel: don't parse FIT partition on NAND-backed mtdblock
Daniel Golle [Sat, 30 Apr 2022 14:14:01 +0000 (15:14 +0100)]
kernel: don't parse FIT partition on NAND-backed mtdblock

ubiblock devices should be used on NAND flash to store the uImage.FIT
in case the bootloader supports that -- otherwise only rootfs is stored
in UBI while the uImage.FIT contains only the kernel and dtb.
Hence there is no need to enable parsing partitions on NAND mtdblock
devices, it is even responsible for the ugly warning on-opening of the
mtdblock device now. Just don't do it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agokernel: backport patch to relax mtdblock NAND warning
Daniel Golle [Sat, 30 Apr 2022 13:24:41 +0000 (14:24 +0100)]
kernel: backport patch to relax mtdblock NAND warning

Instead of warning loudly about mtdblock devices being created, rather
just warn if they are actually used.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: mt7629: disable mtk thermal
Chuanhong Guo [Fri, 29 Apr 2022 03:47:04 +0000 (11:47 +0800)]
mediatek: mt7629: disable mtk thermal

Manually edit kconfig to disable CONFIG_MTK_THERMAL

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: mt7623: disable ecc engine support
Chuanhong Guo [Fri, 29 Apr 2022 03:32:51 +0000 (11:32 +0800)]
mediatek: mt7623: disable ecc engine support

There's no board using nand on this target atm.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: mt7623 enable arch-timer with a patch
Chuanhong Guo [Fri, 29 Apr 2022 02:44:51 +0000 (10:44 +0800)]
mediatek: mt7623 enable arch-timer with a patch

Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.

Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agoipq40xx: 5.10: fix ar40xx driver
Nick Hainke [Mon, 18 Apr 2022 13:04:25 +0000 (15:04 +0200)]
ipq40xx: 5.10: fix ar40xx driver

This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651

The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.

Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617

- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072

Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2 years agomediatek: switch to 5.15
Chuanhong Guo [Thu, 14 Apr 2022 04:45:01 +0000 (12:45 +0800)]
mediatek: switch to 5.15

the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: enable snfi for mt7629
Chuanhong Guo [Sat, 9 Apr 2022 05:26:50 +0000 (13:26 +0800)]
mediatek: enable snfi for mt7629

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: restore support for Fidelix FM35X1GA
Chuanhong Guo [Sat, 9 Apr 2022 12:18:40 +0000 (20:18 +0800)]
mediatek: restore support for Fidelix FM35X1GA

This patch was dropped when the spi-nand driver got replaced last time.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: add an upstreamed spi-nand driver
Chuanhong Guo [Thu, 7 Apr 2022 02:16:47 +0000 (10:16 +0800)]
mediatek: add an upstreamed spi-nand driver

This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: spi-nand: check for 1 byte BBM only
Chuanhong Guo [Thu, 7 Apr 2022 02:05:56 +0000 (10:05 +0800)]
mediatek: spi-nand: check for 1 byte BBM only

the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: v5.15: backport spi-mem ecc support
Chuanhong Guo [Thu, 7 Apr 2022 02:05:25 +0000 (10:05 +0800)]
mediatek: v5.15: backport spi-mem ecc support

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agomediatek: drop spi-nand driver from mtk
Chuanhong Guo [Thu, 7 Apr 2022 02:03:50 +0000 (10:03 +0800)]
mediatek: drop spi-nand driver from mtk

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agoucode: reorder BuildPackage calls
Jo-Philipp Wich [Thu, 28 Apr 2022 08:28:20 +0000 (10:28 +0200)]
ucode: reorder BuildPackage calls

Ensure that the libucode recipe is processed before the ucode one in
order to reliably encode the ABI version into ucode's libucode dependency.

Fixes: #9788
Ref: https://forum.openwrt.org/t/fw4-wont-start-after-upgrade/126308
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agoath79: add support for TP-Link EAP265 HD
Sander Vanheule [Wed, 27 Apr 2022 15:27:28 +0000 (17:27 +0200)]
ath79: add support for TP-Link EAP265 HD

The EAP265 HD is a rebadged EAP245v3, so images are compatible with both
devices.

Link: https://fccid.io/TE7EAP265HD/Letter/6-Request-for-FCC-Change-ID-4823578.pdf
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agofirmware-utils: bump to git HEAD
Sander Vanheule [Wed, 27 Apr 2022 15:27:28 +0000 (17:27 +0200)]
firmware-utils: bump to git HEAD

Includes image support for new TP-Link devices:

  ddc3e00e314d tplink-safeloader: add TP-Link EAP265 HD support
  ceea1a7fe56e tplink-safeloader: add TP-Link Deco M4R v1 and v2 support

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agoiwinfo: update to latest HEAD
David Bauer [Tue, 26 Apr 2022 22:53:11 +0000 (00:53 +0200)]
iwinfo: update to latest HEAD

dc6847e iwinfo: nl80211: omit A-hwmode on non-5GHz hardware

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agonat46: update to git HEAD
Hans Dedecker [Tue, 26 Apr 2022 20:39:02 +0000 (22:39 +0200)]
nat46: update to git HEAD

95ca1c3 nat46-core: ignore IPv4 options when translating packets
39778c2 add a module argument to ignore TOS translate for IPv4
9a36ee1 add a module argument to ignore TOS translate for IPv4
79190a8 add a module argument to ignore TOS translate for IPv4

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 years agouboot-envtools: add WS-AP3825i config
David Bauer [Sun, 24 Apr 2022 22:04:09 +0000 (00:04 +0200)]
uboot-envtools: add WS-AP3825i config

Add configuration to use uboot-envtools with the Extreme Networks
WS-AP3825i.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agompc85xx: set WS-AP3825i mac-address in preinit
David Bauer [Sun, 24 Apr 2022 23:00:49 +0000 (01:00 +0200)]
mpc85xx: set WS-AP3825i mac-address in preinit

The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.

Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agompc85xx: define reset-delay for WS-AP3825i eth PHY
David Bauer [Sun, 24 Apr 2022 21:48:42 +0000 (23:48 +0200)]
mpc85xx: define reset-delay for WS-AP3825i eth PHY

The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.

This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.

Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agodnsmasq: add logfacility file to jail mounts
Daniel Golle [Mon, 25 Apr 2022 17:56:52 +0000 (18:56 +0100)]
dnsmasq: add logfacility file to jail mounts

If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.

Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoiwinfo: update to latest HEAD
David Bauer [Sun, 24 Apr 2022 21:09:09 +0000 (23:09 +0200)]
iwinfo: update to latest HEAD

a479b9b devices: remove whitespace
562d015 iwinfo: nl80211: fix hwmode parsing for multi-band NICs

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agoath79: ubnt: drop swconfig on ac-{lite,lr,mesh}
Martin Weinelt [Sun, 17 Apr 2022 13:56:53 +0000 (15:56 +0200)]
ath79: ubnt: drop swconfig on ac-{lite,lr,mesh}

These don't have switches that could be configured using swconfig.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2 years agoramips: add support for TP-Link RE650 v2
Marcin Gordziejewski [Thu, 7 Apr 2022 22:29:20 +0000 (00:29 +0200)]
ramips: add support for TP-Link RE650 v2

TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
  requires soldering because they're not through holes.

  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.

Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2 years agofirmware-utils: bump to git HEAD
Hauke Mehrtens [Sat, 23 Apr 2022 19:57:09 +0000 (21:57 +0200)]
firmware-utils: bump to git HEAD

05fd700 tplink-safeloader: TP-Link RE650 v2 support

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoramips: add support for YunCore AX820/HWAP-AX820
Clemens Hopfer [Thu, 22 Jul 2021 15:54:15 +0000 (17:54 +0200)]
ramips: add support for YunCore AX820/HWAP-AX820

There are two versions which are identical apart from the enclosure:
  YunCore AX820: indoor ceiling mount AP with integrated antennas
  YunCore HWAP-AX820: outdoor enclosure with external (N) connectors

Hardware specs:
  SoC: MediaTek MT7621DAT
  Flash: 16 MiB SPI NOR
  RAM: 128MiB (DDR3, integrated)
  WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
  Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
  LED: Status (green)
  Button: Reset
  Power: 802.11af/at PoE; DC 12V,1A
  Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external

Flash instructions:
  The "OpenWRT support" version of the AX820 comes with a LEDE-based
  firmware with proprietary MTK drivers and a luci webinterface and
  ssh accessible under 192.168.1.1 on LAN; user root, no password.
  The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
  you will have to force the upgrade due to a different factory name.
  Remember: Do *not* preserve factory configuration!

MAC addresses as used by OEM firmware:
  use   address            source
  2g    44:D1:FA:*:0b      Factory 0x0004 (label)
  5g    46:D1:FA:*:0b      LAA of 2g
  lan   44:D1:FA:*:0c      Factory 0xe000
  wan   44:D1:FA:*:0d      Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.

Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
2 years agokernel: bump 5.15 to 5.15.35
Rui Salvaterra [Wed, 20 Apr 2022 08:07:51 +0000 (09:07 +0100)]
kernel: bump 5.15 to 5.15.35

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agokernel: bump 5.10 to 5.10.112
John Audia [Wed, 20 Apr 2022 10:44:30 +0000 (06:44 -0400)]
kernel: bump 5.10 to 5.10.112

Manually rebased:
  ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agobcm63xx: fix description fix name case
Huangbin Zhan [Wed, 20 Apr 2022 21:40:40 +0000 (05:40 +0800)]
bcm63xx: fix description fix name case

The `Description` should be capital.

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2 years agoath79: ZTE MF286R: add comgt-ncm to DEVICE_PACKAGES
Lech Perczak [Sat, 23 Apr 2022 09:22:50 +0000 (11:22 +0200)]
ath79: ZTE MF286R: add comgt-ncm to DEVICE_PACKAGES

When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.

Fixes: e02fb42c53ba ("comgt: support ZTE MF286R modem")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2 years agomt76: update to the latest version
Felix Fietkau [Sat, 23 Apr 2022 13:50:37 +0000 (15:50 +0200)]
mt76: update to the latest version

a666d5637bc3 mt76: fix tx status related use-after-free race on station removal

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoucode: fix PKG_MIRROR_HASH
Jo-Philipp Wich [Fri, 22 Apr 2022 07:23:49 +0000 (09:23 +0200)]
ucode: fix PKG_MIRROR_HASH

Fixes: 0400774a10 ("ucode: update to latest Git HEAD")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agofirewall4: update to latest Git HEAD
Jo-Philipp Wich [Thu, 21 Apr 2022 19:24:44 +0000 (21:24 +0200)]
firewall4: update to latest Git HEAD

fc83d46 ruleset: set auto-merge directive for interval sets
9bce873 fw4: fix skipping invalid ipset entries
425ea8a fw4: fix applying zone flags for source bound rules

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agoucode: update to latest Git HEAD
Jo-Philipp Wich [Thu, 21 Apr 2022 18:59:15 +0000 (20:59 +0200)]
ucode: update to latest Git HEAD

e14b099 syntax: implement support for ES6 template literals
111cf06 vm: stop executing bytecode on return of nested calls

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agomt76: update to the latest version
Felix Fietkau [Wed, 20 Apr 2022 13:14:14 +0000 (15:14 +0200)]
mt76: update to the latest version

d4937118ec4f mt76: fix rx reordering with non explicit / psmp ack policy
f50672518bcc mt76: do not attempt to reorder received 802.3 packets without agg session
75e046e3c9ae mt76: fix antenna config missing in 6G cap
64ede85f14b5 mt76: mt7915: remove SCS feature
db0a67582028 mt76: mt7915: make read-only array ppet16_ppet8_ru3_ru0 static const
68a2f68d5c01 mt76: mt7921: make read-only array ppet16_ppet8_ru3_ru0 static const
1e7b77294e97 mt76: mt7921: fix kernel crash at mt7921_pci_remove
795830a99a6c mt76: mt7915: add debugfs knob for RF registers read/write
60a8ec12a8eb mt76: mt7603: move spin_lock_bh() to spin_lock()
5ec7a2eac867 mt76: mt7915: disable RX_HDR_TRANS_SHORT
eecbb4992073 mt76: fix encap offload ethernet type check

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: update FIT partition parser to new property name
Daniel Golle [Wed, 20 Apr 2022 14:19:59 +0000 (15:19 +0100)]
kernel: update FIT partition parser to new property name

The commit "uboot-mediatek: replace patch with accepted commit" changed
the name of the boot configuration property from 'bootconf' to
'u-boot,bootconf'. Reflect this change in the FIT partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agouboot-mediatek: replace patch with accepted commit
Daniel Golle [Wed, 20 Apr 2022 14:10:07 +0000 (15:10 +0100)]
uboot-mediatek: replace patch with accepted commit

Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agokernel: x86: remove an upstreamed patch
Rui Salvaterra [Thu, 7 Apr 2022 16:14:38 +0000 (17:14 +0100)]
kernel: x86: remove an upstreamed patch

012-pcengines-apu2-detect-apuv4-board.patch is upstream since Linux 5.5 [1].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.5&id=3d00da1de3ea36ba44f4a7ba76c8c8b16f98204b

Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agowolfssl: fix compilation with /dev/crypto
Eneas U de Queiroz [Wed, 13 Apr 2022 13:30:15 +0000 (10:30 -0300)]
wolfssl: fix compilation with /dev/crypto

This is trivial fix of a duplicate definition of 'int ret'.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agokernel: add missing config symbols
Felix Fietkau [Tue, 19 Apr 2022 19:14:42 +0000 (21:14 +0200)]
kernel: add missing config symbols

MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: use numeric-owner in ipkg-build
Paul Spooren [Tue, 19 Apr 2022 18:02:59 +0000 (20:02 +0200)]
build: use numeric-owner in ipkg-build

To create packages the `ipkg-build` script is used which double packs
`control.tar.gz` and `data.tar.gz` to a single package. By default it's
using a verbose username instead of a numeric value for files.

Official OpenWrt images (artifacts) are created within docker containers
which do not seem to contain those verbose usernames and instead
defaults to numeric values.

This becomes a problem when rebuilding public artifacts because other
build environments may offer verbose usernames and there the created
packages is different from the official ones.

With this commit `ipkg-build` always uses numeric values for user/group
and thereby making it easier to reproduce official artifacts.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agotoolchain: Update glibc 2.34 to recent HEAD
Hauke Mehrtens [Mon, 18 Apr 2022 16:57:54 +0000 (18:57 +0200)]
toolchain: Update glibc 2.34 to recent HEAD

This adds the following changes:

31186e2cb7 elf: Sort tests and modules-names
511b244cc5 elf: Add a comment after trailing backslashes
de6cdd6875 elf/Makefile: Reflow and sort most variable assignments
948ebc098e Fix glibc 2.34 ABI omission (missing GLIBC_2.34 in dynamic loader)
b952c25dc7 x86: Black list more Intel CPUs for TSX [BZ #27398]
aa601d0244 x86: Use CHECK_FEATURE_PRESENT to check HLE [BZ #27398]
e09e7b1492 support: Add support_socket_so_timestamp_time64
e098446037 linux: Fix ancillary 64-bit time timestamp conversion (BZ #28349, BZ#28350)
489d0b8b32 Linux: Only generate 64 bit timestamps for 64 bit time_t recvmsg/recvmmsg
008003dc6e tst-socket-timestamp-compat.c: Check __TIMESIZE [BZ #28837]
05c83ccaf5 linux: __get_nprocs_sched: do not feed CPU_COUNT_S with garbage [BZ #28850]
ad615b59c7 Linux: Simplify __opensock and fix race condition [BZ #28353]
d8302ba2da hurd if_index: Explicitly use AF_INET for if index discovery
6eaf10cbb7 socket: Do not use AF_NETLINK in __opensock
0351c75c5f linux: Fix missing __convert_scm_timestamps (BZ #28860)
d64b08d5ba Add reference to BZ#28860 on NEWS
007e054d78 linux: fix accuracy of get_nprocs and get_nprocs_conf [BZ #28865]
04d60ce0f2 string: Add a testcase for wcsncmp with SIZE_MAX [BZ #28755]
38e0d24794 x86: Fallback {str|wcs}cmp RTM in the ncmp overflow case [BZ #28896]
d093b677c3 x86: Test wcscmp RTM in the wcsncmp overflow case [BZ #28896]
15b00d2af0 x86: Fix TEST_NAME to make it a string in tst-strncmp-rtm.c
d5d1c95aaf NEWS: Add a bug fix entry for BZ #28896
852361b5a3 localedef: Handle symbolic links when generating locale-archive
3be79b72d5 Fix elf/tst-audit2 on hppa
c6f9085ee4 hppa: Fix swapcontext
f610d2935f hppa: Revise gettext trampoline design
40fc6a74ee nptl: Fix cleanups for stack grows up [BZ# 28899]
6c9c230765 hppa: Fix warnings from _dl_lookup_address
b5032c3d37 io: Add fsync call in tst-stat
b53f0c11de nss: Do not mention NSS test modules in <gnu/lib-names.h>
54b1273395 nss: Protect against errno changes in function lookup (bug 28953)
c82bdf033f Don't add access size hints to fortifiable functions
0e6ebf06e4 Make sure that the fortified function conditionals are constant
536910724d debug: Add tests for _FORTIFY_SOURCE=3
98ea9372cc __glibc_unsafe_len: Fix comment
10f7bdebe5 fortify: Fix spurious warning with realpath
d6a58bd81d Enable _FORTIFY_SOURCE=3 for gcc 12 and above
f8c2f620f1 debug: Autogenerate _FORTIFY_SOURCE tests
224d8c1890 debug: Synchronize feature guards in fortified functions [BZ #28746]
738ee53f0c hppa: Implement swapcontext in assembler (bug 28960)
d53b9cc391 hppa: Use END instead of PSEUDO_END in swapcontext.S
4b5b8a1cdf powerpc: Delete unneeded ELF_MACHINE_BEFORE_RTLD_RELOC
b19de59d62 elf: Avoid nested functions in the loader [BZ #27220]
c6df39a0bd elf: Fix elf_get_dynamic_info definition
b868b45f67 elf: Fix dynamic-link.h usage on rtld.c
f6a54a3042 elf: Fix elf_get_dynamic_info() for bootstrap
a31bbe3242 elf: Move LAV_CURRENT to link_lavcurrent.h
e25fe99213 elf: Move la_activity (LA_ACT_ADD) after _dl_add_to_namespace_list() (BZ #28062)
ce0cb6d1d2 elf: Add _dl_audit_objopen
66e9d27a09 elf: Add _dl_audit_activity_map and _dl_audit_activity_nsid
ec0fc2a153 elf: Add _dl_audit_objsearch
198660741b elf: Add _dl_audit_objclose
b2d99731b6 elf: Add _dl_audit_symbind_alt and _dl_audit_symbind
31473c273b elf: Add _dl_audit_preinit
fd9c4e8a1b elf: Add _dl_audit_pltenter
a8e211daea elf: Add _dl_audit_pltexit
29496b3103 elf: Avoid unnecessary slowdown from profiling with audit (BZ#15533)
02c6a3d353 elf: Add audit tests for modules with TLSDESC
d1b9bee29a elf: Issue audit la_objopen for vDSO
2255621f0e elf: Do not fail for failed dlmopen on audit modules (BZ #28061)
98047ba95c elf: Add la_activity during application exit
efb21b5fb2 elf: Fix initial-exec TLS access on audit modules (BZ #28096)
056fc1c0e3 elf: Issue la_symbind for bind-now (BZ #23734)
b118bce87a elf: Fix runtime linker auditing on aarch64 (BZ #26643)
165e7ad459 Fix elf/tst-audit25a with default bind now toolchains
aabdad371f elf: Replace tst-audit24bmod2.so with tst-audit24bmod2
4dca2d3a7b hppa: Fix bind-now audit (BZ #28857)
ceed89d089 NEWS: Update fixed bug list for LD_AUDIT backports.
0c03cb54c8 S390: Add new s390 platform z16.
290db09546 nptl: Handle spurious EINTR when thread cancellation is disabled (BZ#29029)
5d8c777634 hurd: Fix arbitrary error code
b87b697f15 mips: Fix mips64n32 64 bit time_t stat support (BZ#29069)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agouboot-mediatek: remove '0x' prefix from pstore node
Daniel Golle [Tue, 19 Apr 2022 15:27:22 +0000 (16:27 +0100)]
uboot-mediatek: remove '0x' prefix from pstore node

Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: mt7622: remove '0x' prefix from pstore address in dts
Daniel Golle [Tue, 19 Apr 2022 15:23:08 +0000 (16:23 +0100)]
mediatek: mt7622: remove '0x' prefix from pstore address in dts

Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.

Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.

See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobase-files: minimize critical time in sysupgrade
Rodrigo Balerdi [Fri, 15 Apr 2022 10:20:28 +0000 (07:20 -0300)]
base-files: minimize critical time in sysupgrade

Attempt to minimize the time during which an interrupted nand sysupgrade
can lead to a non-functional device by flushing caches before starting
the upgrade procedure.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: trim unnecessary nand sysupgrade code
Rodrigo Balerdi [Fri, 15 Apr 2022 13:15:02 +0000 (10:15 -0300)]
base-files: trim unnecessary nand sysupgrade code

Remove unnecessary sync commands during nand sysupgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: fix issues in nand sysupgrade
Rodrigo Balerdi [Fri, 15 Apr 2022 13:11:52 +0000 (10:11 -0300)]
base-files: fix issues in nand sysupgrade

Fix issues while retaining configuration during nand sysupgrade:
- abort configuration saving if data partition is not found
- generate diagnostics if saving fails (eg, because of lack of space)
- do not output "sysupgrade successful" in case of errors

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: clean up nand sysupgrade code
Rodrigo Balerdi [Fri, 15 Apr 2022 10:18:22 +0000 (07:18 -0300)]
base-files: clean up nand sysupgrade code

Fix some inconsistent quoting in nand sysupgrade code.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: clean up ubinized sysupgrade code
Rodrigo Balerdi [Fri, 15 Apr 2022 09:42:51 +0000 (06:42 -0300)]
base-files: clean up ubinized sysupgrade code

Remove redundant check from nand ubinized sysupgrade code. This check
has already been done in the only caller of the affected function:
nand_do_upgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: clean up nand tar sysupgrade code
Rodrigo Balerdi [Fri, 15 Apr 2022 09:31:24 +0000 (06:31 -0300)]
base-files: clean up nand tar sysupgrade code

Prepares code for ubirename-based safe sysupgrade implementation.

Fixes several issues:
- the special CI_KERNPART value "none" is ignored if an MTD partition
  named "none" exists
- misleading variable names (such as has_kernel to mean "tar has kernel
  and it should not be written to an MTD partition but a UBI volume")
- inconsistent treatment of zero-length tar member files
- inconsistent meaning of "0" and "" variable values
- redundant operations (unneeded untaring, repeated untaring, unneeded
  partition lookups)
- inconsistent variable quoting

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: safer sysupgrade.tar for kernel-out-of-UBI
Rodrigo Balerdi [Fri, 15 Apr 2022 06:24:58 +0000 (03:24 -0300)]
base-files: safer sysupgrade.tar for kernel-out-of-UBI

Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, such as TFTP, instead of just going
ahead with normal boot and effectively bricking the device.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: safer sysupgrade for kernel-in-UBI devices
Rodrigo Balerdi [Fri, 15 Apr 2022 03:59:49 +0000 (00:59 -0300)]
base-files: safer sysupgrade for kernel-in-UBI devices

Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, instead of just going ahead with
normal boot and effectively bricking the device.

Possible fallbacks include a recovery initramfs partition or UBI volume
and TFTP. See here for an example U-Boot configuration with fallbacks:
https://shorturl.at/befsA (https://github.com/Lanchon/openwrt-tr4400-v2/
blob/e7d707d6bd7839fbd0b8d0bd180fce451df77e47/install-recovery.sh#L52-L63)

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: fix nand sysupgrade comments
Rodrigo Balerdi [Fri, 15 Apr 2022 03:53:27 +0000 (00:53 -0300)]
base-files: fix nand sysupgrade comments

Erroneous comments possibly applied to an earlier code revision.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: improve sysupgrade ubiblock handling
Rodrigo Balerdi [Fri, 15 Apr 2022 03:52:12 +0000 (00:52 -0300)]
base-files: improve sysupgrade ubiblock handling

Only remove ubiblock devices required for nand sysupgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agobase-files: emit diagnostics on sysupgrade abort
Rodrigo Balerdi [Fri, 15 Apr 2022 03:44:26 +0000 (00:44 -0300)]
base-files: emit diagnostics on sysupgrade abort

Emit diagnostics if nand sysupgrade is aborted because UBI partition
cannot be attached. Also avoid redudndant checks.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agomediatek: remove crypto-hw-mtk package
Eneas U de Queiroz [Thu, 31 Mar 2022 13:38:49 +0000 (10:38 -0300)]
mediatek: remove crypto-hw-mtk package

The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoath79: add support for MikroTik RouterBOARD wAP-2nD (wAP)
David Musil [Sat, 16 Apr 2022 12:01:31 +0000 (12:01 +0000)]
ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP)

The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - Flash: 16 MB (SPI)
 - RAM: 64 MB
 - Ethernet: 1x 10/100 Mbps (PoE in)
 - WiFi: AR9531 2T2R 2.4 GHz (SoC)
 - 3x green LEDs (1x lan, 1x wlan, 1x user)

 See https://mikrotik.com/product/RBwAP2nD for more info.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Note: following 781d4bfb397cdd12ee0151eb66c577f470e3377d
 The network setup avoids using the integrated switch and connects the
 single Ethernet port directly. This way, link speed (10/100 Mbps) is
 properly reported by eth0.

Signed-off-by: David Musil <0x444d@protonmail.com>
2 years agomac80211: fix QCA9561 PA bias
Thibaut VARÈNE [Sun, 17 Apr 2022 15:03:52 +0000 (17:03 +0200)]
mac80211: fix QCA9561 PA bias

This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs),
following a suggestion from nbd[1].

This patch has been submitted upstream[2].

[1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
[2] https://lore.kernel.org/linux-wireless/20220417145145.1847-1-hacks+kernel@slashdirt.org/

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2 years agolinux-firmware: Update to version 20220411
Hauke Mehrtens [Mon, 11 Apr 2022 22:12:57 +0000 (00:12 +0200)]
linux-firmware: Update to version 20220411

The following files used in OpenWrt changed:
 amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam17h.bin
 amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam19h.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/aldebaran_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/arcturus_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/beige_goby_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/dcn_3_1_6_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/green_sardine_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi10_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma1.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi12_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navi14_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/picasso_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_toc.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven2_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/raven_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/renoir_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/sdma_5_2_7.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_dmcub.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sdma.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_smc.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sos.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ta.bin
 amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_vcn.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vangogh_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega10_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega12_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/vega20_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_asd.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ce.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_me.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec2.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_pfp.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_rlc.bin
 amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ta.bin
 ibt-firmware/lib/firmware/intel/ibt-hw-37.8.10-fw-22.50.19.14.f.bseq
 iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
 iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
 iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoramips: add support for OrayBox X3A
Ray Wang [Sat, 12 Mar 2022 14:57:12 +0000 (22:57 +0800)]
ramips: add support for OrayBox X3A

OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.

Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
  * 2.4GHz: MT7615
  * 5GHz: MT7615
* Ethernet: 3x 1000Mbps
  * Switch: MT7530
* LED:
  * Ethernet LEDs: On the back of the router, hardware-controlled.
  * Status LEDs: One "pixel-like" RGB LED in the front of the router,
                 which is actually made up of 3 individual LEDs (with
                 dedicated GPIO pins) with the color of Red, Green,
                 and Blue.
                 The OEM firmware only lights up one color at a time to
                 indicate status, but that's very boring, and the colors
                 actually look great when combined, so I've improvised a
                 little and made them indicate netdev activities.
                 My test results:
                 GPIO 13/14/15
                 000 white (actually more like bright green or cyan
                            because the brightness of the green LED is
                            higher than red and blue)
                 001 bright purple
                 010 bright green
                 011 red
                 100 bright cyan
                 101 blue
                 110 green
                 111 off

Flash Layout:
 0x0000000-0x0030000 : "u-boot"
 0x0030000-0x0040000 : "u-boot-env"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x0f50000 : "firmware"
 /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
 0x0fe0000-0x0ff0000 : "bdinfo"
 0x0ff0000-0x1000000 : "reserve"

MAC address:
 MAC               Source                          Description    Fix
 A0:CX:XX:BX:XX:0D BDINFO_9                        LAN(LABEL)     DTS
 A0:CX:XX:BX:XX:0E BDINFO_9 + 1                    WAN            DTS
 A2:CX:XX:BX:XX:0F FACTORY_4                       WIFI2G         DTS
 A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G         HOTPLUG
 A6:CX:XX:BX:XX:0F N/A                             WIFI2G_CLIENT  N/A
 A6:DX:XX:BX:XX:0F N/A                             WIFI5G_CLIENT  N/A

Stock dmesg:
https://pastebin.com/2t2jwLdf

Stock Dumps:
https://pastebin.com/LDLxSWX3

Installation via SSH (does not void your warranty):
1.  -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
    your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
    config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
    "config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
    button. The router will automatically reboot.
2.  -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
    folder to your router. It should be root@10.168.1.1 and the password
    is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
    backup the stock firmware. Since the OEM does not provide firmware
    download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
    firmware from '/tmp/' to your local drive. Then you'd better use a hex
    reading tool to have a rough look at it to make sure nothing is
    corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
    the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
    reboot the router.

Revert to stock firmware:
1.  load stock firmware using mtd (make sure u have a backup).

Signed-off-by: Ray Wang <raywang777@foxmail.com>
2 years agoRevert "mac80211 adjust QCA9561 PA bias"
Petr Štetiar [Sun, 17 Apr 2022 07:07:49 +0000 (09:07 +0200)]
Revert "mac80211 adjust QCA9561 PA bias"

This reverts commit f9ff282d17ec652d63fa2404e47bb0e15ed95b69 as during
upstream patch review process nbd pointed out, that this patch needs
more work:

 "The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
  correct register, the definition has an explicit check for 9561 as well.
  I believe this patch works by accident because it avoids writing a wrong
  value to that register."

1. https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agorealtek: add ZyXEL GS1900-24HP v1 support
Martin Kennedy [Sat, 5 Mar 2022 19:02:36 +0000 (14:02 -0500)]
realtek: add ZyXEL GS1900-24HP v1 support

The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HP v1
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
  * 1 PWR LED (green, not configurable)
  * 1 SYS LED (green, configurable)
  * 24 ethernet port link/activity LEDs (green, SoC controlled)
  * 24 ethernet port PoE status LEDs
  * 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
  * 1 "RESET" button on front panel (soft reset)
  * 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
  * Management MCU: ST Micro ST32F100 Microcontroller
  * 6 BCM59111 PSE chips
  * 170W power budget
* Power:     120-240V AC C13
* UART:      Internal populated 10-pin header ('J5') providing RS232;
             connected to SoC UART through a TI or SIPEX 3232C for voltage
             level shifting.

* 'J5' RS232 Pinout (dot as pin 1):
  2) SoC RXD
  3) GND
  10) SoC TXD

Serial connection parameters: 115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface

* Navigate to Maintenance > Firmware > Management

* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.

* Navigate to Maintenance > Firmware > Upload

* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot
  the switch.

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).

* Set up a TFTP server on your client and make it serve the initramfs
  image.

* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:

  > rtk network on

* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only be installed in the first partition anyway (hardcoded in the
  DTS). To ensure we are set to boot from the first partition, issue the
  following commands:

  > setsys bootpartition 0
  > savesys

* Download the image onto the device and boot from it:

  > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  > bootm

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agoipq806x: RT4230W: utilize nvmem-cells for ath10k caldata
Chukun Pan [Thu, 10 Feb 2022 13:26:40 +0000 (21:26 +0800)]
ipq806x: RT4230W: utilize nvmem-cells for ath10k caldata

Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.

Same as commit 2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
2 years agoipq806x: Askey RT4230W REV6: enable onboard spi flash
Chukun Pan [Wed, 9 Jun 2021 15:22:50 +0000 (23:22 +0800)]
ipq806x: Askey RT4230W REV6: enable onboard spi flash

There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.

[    3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[    3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2 years agoath79: add support for Sophos AP100/AP55 family
Andrew Powers-Holmes [Fri, 3 Sep 2021 13:53:57 +0000 (23:53 +1000)]
ath79: add support for Sophos AP100/AP55 family

The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.

The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.

Specifications common to all models:
 - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
 - 128 MB RAM
 - 16 MB SPI flash
 - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
 - Green and Red status LEDs sharing a single external light-pipe
 - Reset button on PCB[1]
 - Piezo beeper on PCB[2]
 - Serial UART header on PCB
 - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC

Unique to AP100 and AP100C:
 - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
 - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)

AP55 and AP55C:
 - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
 - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)

AP100 and AP55:
 - External RJ45 serial console port[3]
 - USB 2.0 Type A port, power controlled via GPIO 11

Flashing instructions:

This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.

To flash via XG appliance:
 - Register on Sophos' website for a no-cost Home Use XG firewall license
 - Download and install the XG software on a compatible PC or virtual
   machine, complete initial appliance setup, and enable SSH console access
 - Connect the target AP device to the XG appliance's LAN interface
 - Approve the AP from the XG Web UI and wait until it shows as Active
   (this can take 3-5 minutes)
 - Connect to the XG appliance over SSH and access the Advanced Console
   (Menu option 5, then menu option 3)
 - Run `sudo awetool` and select the menu option to connect to an AP via
   SSH. When prompted to enable SSH on the target AP, select Yes.
 - Wait 2-3 minutes, then select the AP from the awetool menu again. This
   will connect you to a root shell on the target AP.
 - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
 - Run `mtd -r write /tmp/openwrt.bin astaro_image`
 - When complete, the access point will reboot to OpenWRT.

To flash via U-Boot serial console:
 - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
   netmask 255.255.255.0
 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
 - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
 - Connect the AP ethernet to your PC's ethernet port
 - Connect a terminal to the UART at 115200 8/N/1 as usual
 - Power on the AP and press a key to cancel autoboot when prompted
 - Run the following commands at the U-Boot console:
    - `tftpboot`
    - `cp.b $fileaddr 0x9f070000 $filesize`
    - `boot`
 - The access point will boot to OpenWRT.

MAC addresses as verified by OEM firmware:

use   address     source
LAN   label       config 0x201a (label)
2g    label + 1   art 0x1002    (also found at config 0x2004)
5g    label + 9   art 0x5006

Increments confirmed across three AP55C, two AP55, and one AP100C.

These changes have been tested to function on both current master and
21.02.0 without any obvious issues.

[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
    any GPIO. Shorting an unpopulated resistor next to the driver circuitry
    should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
    works in OpenWRT without additional configuration, at least on my
    three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
    the device's top cover. On AP100C/AP55C models, the PCB must be removed
    for access; three screws secure it to the case.
    Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX

Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
2 years agoath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
Ryan Mounce [Sat, 10 Apr 2021 02:56:49 +0000 (12:26 +0930)]
ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)

This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)

Specifications:
- SoC: QCA9558
- RAM: 128 MB
- Flash: 16 MB SPI
- 2.4GHz WLAN: 3x3:3 802.11n on SoC
- 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe
- Switch: 5x 1000/100/10 on QCA8337 connected via RGMII
- SFP cage: connected via SGMII (tested with genuine & generic GLC-T)
- USB: 1x type A, GPIO power switch
- PoE: Passive input on Ether1, GPIO switched passthrough to Ether5
- Reset button
- "SFP" LED connected to SoC
- Ethernet LEDs connected to QCA8337 switch
- Green WLAN LED connected to QCA9880

Not working:
- Red WLAN LED

Installation:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2 years agoramips: mt7621: make u_env partition r/w for Linksys EA7xxx devices
Russell Morris [Fri, 8 Apr 2022 18:29:13 +0000 (13:29 -0500)]
ramips: mt7621: make u_env partition r/w for Linksys EA7xxx devices

Make u_env partition read/write - currently cannot write to it, which
blocks fw_setenv. This in turn breaks features like Advanced Reboot,
which rely on setting the environment variable boot_part (1 or 2).

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
2 years agoramips: add support for ASUS RT-AC1200-V2
Tamas Balogh [Fri, 15 Apr 2022 09:11:01 +0000 (11:11 +0200)]
ramips: add support for ASUS RT-AC1200-V2

Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC

MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000

Serial console: 57600,8n1

Installation:

Asus windows recovery tool:

install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:

set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2 years agoscripts: format to black
Doug Kerr [Fri, 15 Apr 2022 19:54:30 +0000 (15:54 -0400)]
scripts: format to black

clean up formatting with black using 80 character line limit

Signed-off-by: Doug Kerr <dek3rr@gmail.com>
2 years agoscripts: use std library for jam crc32 calculation
Doug Kerr [Fri, 15 Apr 2022 19:47:32 +0000 (15:47 -0400)]
scripts: use std library for jam crc32 calculation

CRC32 is available in a standard library. It seems reasonable
to defer to that rather than run a custom implementation.

Signed-off-by: Doug Kerr <dek3rr@gmail.com>
2 years agokernel: bump 5.15 to 5.15.34
Rui Salvaterra [Thu, 14 Apr 2022 08:28:11 +0000 (09:28 +0100)]
kernel: bump 5.15 to 5.15.34

Deleted (upstreamed):
generic/pending-5.15/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.34&id=60eabd66d17fa2cbc31f670b2f201f0bc54090a2

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agokernel: bump 5.10 to 5.10.111
John Audia [Wed, 13 Apr 2022 20:25:50 +0000 (16:25 -0400)]
kernel: bump 5.10 to 5.10.111

Removed upstreamed:
  pending-5.10/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch
  apm821xx/patches-5.10/150-ata-sata_dwc_460ex-Fix-crash-due-to-OOB-write.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agoramips: add support for BOLT! Arion
Abdul Aziz Amar [Mon, 14 Mar 2022 09:26:23 +0000 (05:26 -0400)]
ramips: add support for BOLT! Arion

This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.

Specifications:

- SoC:      MediaTek MT7621
- Flash:    32 MiB NOR SPI
- RAM:      128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs:     Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
            Non-programmable "Power"  LED
- Buttons:  Reset and WPS

Instalation:
Install from TFTP

Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name

You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8

There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.

Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
2 years agoramips: add support for Wavlink WL-WN531A3
Davide Fioravanti [Wed, 16 Mar 2022 01:18:11 +0000 (02:18 +0100)]
ramips: add support for Wavlink WL-WN531A3

The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.

Hardware
--------
SoC:   Mediatek MT7628AN
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
  - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 2.0 port
UART:
  - 57600-8-N-1
    J1
      O VCC +3,3V (near lan ports)
      o RX
      o TX
      o GND

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
-rw-r--r--    1 0        0         8388608 /etc_ro/lighttpd/www/dev/mtd0ro

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/

6) After few seconds, in the textarea should appear this output:
-rw-r--r--    1 0        0          196608 mtd1ro
-rw-r--r--    1 0        0           65536 mtd2ro
-rw-r--r--    1 0        0           65536 mtd3ro
-rw-r--r--    1 0        0         8060928 mtd4ro
drwxr-xr-x    7 0        0               0 ..
drwxr-xr-x    2 0        0               0 .

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1ro
http://192.168.10.1/dev/mtd2ro
http://192.168.10.1/dev/mtd3ro
http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN XX:XX:XX:XX:XX:9B (factory @ 0x28)
   WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e)
   WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04)
   WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004)

   LABEL XX:XX:XX:XX:XX:9D

2) There is just one wifi led for both wifi interfaces.
   It currently shows only the 2.4 GHz wifi activity.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2 years agoreadline: add host PIC
Rosen Penev [Thu, 31 Mar 2022 04:33:01 +0000 (21:33 -0700)]
readline: add host PIC

Python seems to fail to link to libreadline properly because of this.
Not a fatal error but an error nontheless.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agopcre: pass -fPIC under host as well
Rosen Penev [Sun, 27 Mar 2022 20:27:15 +0000 (13:27 -0700)]
pcre: pass -fPIC under host as well

static libraries need them as they are not PIC by default.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agolantiq: fritz736x: Move GPIO resets to the inidvidual board.dts files
Martin Blumenstingl [Fri, 18 Mar 2022 22:36:41 +0000 (23:36 +0100)]
lantiq: fritz736x: Move GPIO resets to the inidvidual board.dts files

FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agocomgt: support ZTE MF286R modem
Cezary Jackiewicz [Sun, 27 Feb 2022 13:12:39 +0000 (14:12 +0100)]
comgt: support ZTE MF286R modem

The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2 years agocomgt: ncm: try to detect interface for ttyACM ports
Lech Perczak [Thu, 31 Mar 2022 19:16:34 +0000 (21:16 +0200)]
comgt: ncm: try to detect interface for ttyACM ports

Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.

Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2 years agocomgt: ncm: select first available network interface for device
Lech Perczak [Thu, 31 Mar 2022 19:16:22 +0000 (21:16 +0200)]
comgt: ncm: select first available network interface for device

Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>