qualcommax: ipq807x: add support for Linksys MX8500
authorPaweł Owoc <frut3k7@gmail.com>
Mon, 26 Feb 2024 10:38:02 +0000 (11:38 +0100)
committerRobert Marko <robimarko@gmail.com>
Thu, 16 May 2024 18:27:36 +0000 (20:27 +0200)
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel

5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
package/boot/uboot-envtools/files/qualcommax_ipq807x
package/firmware/ipq-wifi/Makefile
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts [new file with mode: 0644]
target/linux/qualcommax/image/ipq807x.mk
target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh

index 312fdf8d871eae7fe7658c0a99342435b11dac42..060871396b4ea9c4ee261b67ff29c96955317b35 100644 (file)
@@ -31,7 +31,8 @@ edimax,cax1800)
        ;;
 linksys,mx4200v1|\
 linksys,mx4200v2|\
-linksys,mx5300)
+linksys,mx5300|\
+linksys,mx8500)
        idx="$(find_mtd_index u_env)"
        [ -n "$idx" ] && \
                ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
index 68448a6ec1d1f909074cf6cac7f64b8daba5864a..2ffd2e014c7fd117e130e1ee58a97ebca7937c47 100644 (file)
@@ -37,6 +37,7 @@ ALLWIFIBOARDS:= \
        edimax_cax1800 \
        linksys_mx4200 \
        linksys_mx5300 \
+       linksys_mx8500 \
        netgear_lbr20 \
        netgear_rax120v2 \
        netgear_wax214 \
@@ -157,6 +158,7 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
 $(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
 $(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
 $(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
+$(eval $(call generate-ipq-wifi-package,linksys_mx8500,Linksys MX8500))
 $(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
 $(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
 $(eval $(call generate-ipq-wifi-package,netgear_wax214,Netgear WAX214))
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-mx8500.dts
new file mode 100644 (file)
index 0000000..70f4438
--- /dev/null
@@ -0,0 +1,523 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+       model = "Linksys MX8500";
+       compatible = "linksys,mx8500", "qcom,ipq8074";
+
+       aliases {
+               serial0 = &blsp1_uart5;
+               serial1 = &blsp1_uart3;
+               led-boot = &led_system_blue;
+               led-running = &led_system_blue;
+               led-failsafe = &led_system_red;
+               led-upgrade = &led_system_green;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+               bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
+       };
+
+       gpio_export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               bt_pwr {
+                       gpio-export,name = "bt_pwr";
+                       gpio-export,output = <1>;
+                       gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+               pinctrl-0 = <&button_pins>;
+               pinctrl-names = "default";
+
+               reset-button {
+                       label = "reset";
+                       gpios = <&tlmm 67 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps-button {
+                       label = "wps";
+                       gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+};
+
+&tlmm {
+       button_pins: button-state {
+               pins = "gpio64", "gpio67";
+               function = "gpio";
+               drive-strength = <8>;
+               bias-pull-up;
+       };
+
+       mdio_pins: mdio-state {
+               mdc-pins {
+                       pins = "gpio68";
+                       function = "mdc";
+                       drive-strength = <8>;
+                       bias-pull-up;
+               };
+
+               mdio-pins {
+                       pins = "gpio69";
+                       function = "mdio";
+                       drive-strength = <8>;
+                       bias-pull-up;
+               };
+       };
+};
+
+&blsp1_uart3 {
+       status = "okay";
+};
+
+&blsp1_uart5 {
+       status = "okay";
+};
+
+&prng {
+       status = "okay";
+};
+
+&cryptobam {
+       status = "okay";
+};
+
+&crypto {
+       status = "okay";
+};
+
+&qpic_bam {
+       status = "okay";
+};
+
+&qpic_nand {
+       status = "okay";
+
+       /*
+        * Bootloader will find the NAND DT node by the compatible and
+        * then "fixup" it by adding the partitions from the SMEM table
+        * using the legacy bindings thus making it impossible for us
+        * to change the partition table or utilize NVMEM for calibration.
+        * So add a dummy partitions node that bootloader will populate
+        * and set it as disabled so the kernel ignores it instead of
+        * printing warnings due to the broken way bootloader adds the
+        * partitions.
+        */
+       partitions {
+               status = "disabled";
+       };
+
+       nand@0 {
+               reg = <0>;
+               nand-ecc-strength = <4>;
+               nand-ecc-step-size = <512>;
+               nand-bus-width = <8>;
+
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "0:sbl1";
+                               reg = <0x0 0x100000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "0:mibib";
+                               reg = <0x100000 0x100000>;
+                               read-only;
+                       };
+
+                       partition@200000 {
+                               label = "0:bootconfig";
+                               reg = <0x200000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@280000 {
+                               label = "0:bootconfig1";
+                               reg = <0x280000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@300000 {
+                               label = "0:qsee";
+                               reg = <0x300000 0x300000>;
+                               read-only;
+                       };
+
+                       partition@600000 {
+                               label = "0:qsee_1";
+                               reg = <0x600000 0x300000>;
+                               read-only;
+                       };
+
+                       partition@900000 {
+                               label = "0:devcfg";
+                               reg = <0x900000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@980000 {
+                               label = "0:devcfg_1";
+                               reg = <0x980000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@a00000 {
+                               label = "0:apdp";
+                               reg = <0xa00000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@a80000 {
+                               label = "0:apdp_1";
+                               reg = <0xa80000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@b00000 {
+                               label = "0:rpm";
+                               reg = <0xb00000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@b80000 {
+                               label = "0:rpm_1";
+                               reg = <0xb80000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@c00000 {
+                               label = "0:cdt";
+                               reg = <0xc00000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@c80000 {
+                               label = "0:cdt_1";
+                               reg = <0xc80000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@d00000 {
+                               label = "0:appsblenv";
+                               reg = <0xd00000 0x80000>;
+                       };
+
+                       partition@d80000 {
+                               label = "0:appsbl";
+                               reg = <0xd80000 0x100000>;
+                               read-only;
+                       };
+
+                       partition@e80000 {
+                               label = "0:appsbl_1";
+                               reg = <0xe80000 0x100000>;
+                               read-only;
+                       };
+
+                       partition@f80000 {
+                               label = "0:art";
+                               reg = <0xf80000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@1000000 {
+                               label = "u_env";
+                               reg = <0x1000000 0x40000>;
+                       };
+
+                       partition@1040000 {
+                               label = "s_env";
+                               reg = <0x1040000 0x20000>;
+                       };
+
+                       partition@1060000 {
+                               label = "devinfo";
+                               reg = <0x1060000 0x20000>;
+                               read-only;
+                       };
+
+                       partition@1080000 {
+                               label = "kernel";
+                               reg = <0x1080000 0x9600000>;
+                       };
+
+                       partition@1680000 {
+                               label = "rootfs";
+                               reg = <0x1680000 0x9000000>;
+                       };
+
+                       partition@a680000 {
+                               label = "alt_kernel";
+                               reg = <0xa680000 0x9600000>;
+                       };
+
+                       partition@ac80000 {
+                               label = "alt_rootfs";
+                               reg = <0xac80000 0x9000000>;
+                       };
+
+                       partition@13c80000 {
+                               label = "sysdiag";
+                               reg = <0x13c80000 0x200000>;
+                               read-only;
+                       };
+
+                       partition@13e80000 {
+                               label = "0:ethphyfw";
+                               reg = <0x13e80000 0x100000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       aqr_fw: firmware@0 {
+                                               /* Skip the QCOM MBN Header of 40 bytes */
+                                               reg = <0x28 0x60002>;
+                                       };
+                               };
+                       };
+
+                       partition@13f80000 {
+                               label = "syscfg";
+                               reg = <0x13f80000 0xb180000>;
+                               read-only;
+                       };
+
+                       partition@1f100000 {
+                               label = "app_data";
+                               reg = <0x1f100000 0x500000>;
+                               read-only;
+                       };
+
+                       partition@1f600000 {
+                               label = "0:wififw";
+                               reg = <0x1f600000 0xa00000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&blsp1_i2c2 {
+       status = "okay";
+
+       led-controller@62 {
+               compatible = "nxp,pca9633";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0x62>;
+               nxp,hw-blink;
+
+               led_system_red: led@0 {
+                       reg = <0>;
+                       color = <LED_COLOR_ID_RED>;
+                       function = LED_FUNCTION_STATUS;
+               };
+
+               led_system_green: led@1 {
+                       reg = <1>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_STATUS;
+               };
+
+               led_system_blue: led@2 {
+                       reg = <2>;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_STATUS;
+               };
+       };
+};
+
+&mdio {
+       status = "okay";
+
+       pinctrl-0 = <&mdio_pins>;
+       pinctrl-names = "default";
+       reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+       ethernet-phy-package@0 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               compatible = "qcom,qca8075-package";
+               reg = <0>;
+
+               qcom,package-mode = "qsgmii";
+
+               qca8075_0: ethernet-phy@0 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <0>;
+               };
+
+               qca8075_1: ethernet-phy@1 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <1>;
+               };
+
+               qca8075_2: ethernet-phy@2 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <2>;
+               };
+
+               qca8075_3: ethernet-phy@3 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <3>;
+               };
+       };
+
+       aqr114c: ethernet-phy@8 {
+               compatible = "ethernet-phy-ieee802.3-c45";
+               reg = <8>;
+               reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+               firmware-name = "marvell/AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld";
+               nvmem-cells = <&aqr_fw>;
+               nvmem-cell-names = "firmware";
+       };
+};
+
+&switch {
+       status = "okay";
+
+       switch_lan_bmp = <(ESS_PORT1 | ESS_PORT2 | ESS_PORT3 | ESS_PORT4)>; /* lan port bitmap */
+       switch_wan_bmp = <ESS_PORT6>; /* wan port bitmap */
+       switch_mac_mode = <MAC_MODE_QSGMII>; /* mac mode for uniphy instance0*/
+       switch_mac_mode2 = <MAC_MODE_USXGMII>; /* mac mode for uniphy instance2*/
+
+       qcom,port_phyinfo {
+               port@1 {
+                       port_id = <1>;
+                       phy_address = <0>;
+               };
+
+               port@2 {
+                       port_id = <2>;
+                       phy_address = <1>;
+               };
+
+               port@3 {
+                       port_id = <3>;
+                       phy_address = <2>;
+               };
+
+               port@4 {
+                       port_id = <4>;
+                       phy_address = <3>;
+               };
+
+               port@6 {
+                       port_id = <6>;
+                       phy_address = <8>;
+                       compatible = "ethernet-phy-ieee802.3-c45";
+                       ethernet-phy-ieee802.3-c45;
+               };
+       };
+};
+
+&edma {
+       status = "okay";
+};
+
+&dp1 {
+       status = "okay";
+       phy-mode = "qsgmii";
+       phy-handle = <&qca8075_0>;
+       label = "lan1";
+};
+
+&dp2 {
+       status = "okay";
+       phy-mode = "qsgmii";
+       phy-handle = <&qca8075_1>;
+       label = "lan2";
+};
+
+&dp3 {
+       status = "okay";
+       phy-mode = "qsgmii";
+       phy-handle = <&qca8075_2>;
+       label = "lan3";
+};
+
+&dp4 {
+       status = "okay";
+       phy-mode = "qsgmii";
+       phy-handle = <&qca8075_3>;
+       label = "lan4";
+};
+
+&dp6_syn {
+       status = "okay";
+       phy-mode = "usxgmii";
+       phy-handle = <&aqr114c>;
+       label = "wan";
+};
+
+&ssphy_0 {
+       status = "okay";
+};
+
+&qusb_phy_0 {
+       status = "okay";
+};
+
+&usb_0 {
+       status = "okay";
+};
+
+&pcie_qmp0 {
+       status = "okay";
+};
+
+&pcie0 {
+       status = "okay";
+
+       perst-gpio = <&tlmm 61 GPIO_ACTIVE_LOW>;
+
+       bridge@0,0 {
+               reg = <0x00000000 0 0 0 0>;
+               #address-cells = <3>;
+               #size-cells = <2>;
+               ranges;
+
+               wifi@1,0 {
+                       status = "okay";
+
+                       /* ath11k has no DT compatible for PCI cards */
+                       compatible = "pci17cb,1104";
+                       reg = <0x00010000 0 0 0 0>;
+
+                       qcom,ath11k-calibration-variant = "Linksys-MX8500";
+               };
+       };
+};
+
+&wifi {
+       status = "okay";
+
+       qcom,ath11k-calibration-variant = "Linksys-MX8500";
+};
index a4fd6ff7969044de012504a1aa52f6c7bca25555..007c73555e2254926b650358bda45b694c32dc0e 100644 (file)
@@ -140,6 +140,14 @@ define Device/linksys_mx5300
 endef
 TARGET_DEVICES += linksys_mx5300
 
+define Device/linksys_mx8500
+       $(call Device/linksys_mx)
+       DEVICE_MODEL := MX8500
+       DEVICE_PACKAGES += ipq-wifi-linksys_mx8500 kmod-ath11k-pci \
+               ath11k-firmware-qcn9074 kmod-bluetooth
+endef
+TARGET_DEVICES += linksys_mx8500
+
 define Device/netgear_rax120v2
        $(call Device/FitImage)
        $(call Device/UbiFit)
index d87e4246e1a36ed999a78f9ab33df8e2c5740391..380588bbab14d87e82552a1f1093c7fce487a481 100644 (file)
@@ -15,6 +15,7 @@ ipq807x_setup_interfaces()
        buffalo,wxr-5950ax12|\
        dynalink,dl-wrx36|\
        linksys,mx5300|\
+       linksys,mx8500|\
        xiaomi,ax9000|\
        zbtlink,zbt-z800ax)
                ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
@@ -76,6 +77,11 @@ ipq807x_setup_macs()
                        done
                        [ "$(mtd_get_mac_ascii u_env eth2addr)" != "$label_mac" ] && wan_mac=$label_mac
                ;;
+               linksys,mx8500)
+                       label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+                       lan_mac=$(macaddr_add $label_mac 1)
+                       wan_mac=$label_mac
+               ;;
        esac
 
        [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
index c40d9bc5f9edcefeac5ae678f7e9f32143014779..018e8288590b96ad829134f3c90cebbf89719b1c 100644 (file)
@@ -29,7 +29,8 @@ case "$FIRMWARE" in
        zte,mf269)
                caldata_extract "0:art" 0x1000 0x20000
                ;;
-       linksys,mx4200v1)
+       linksys,mx4200v1|\
+       linksys,mx8500)
                caldata_extract "0:art" 0x1000 0x20000
                ath11k_remove_regdomain
                ;;
@@ -66,6 +67,10 @@ case "$FIRMWARE" in
 "ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin"|\
 "ath11k/QCN9074/hw1.0/cal-pci-0001:01:00.0.bin")
        case "$board" in
+       linksys,mx8500)
+               caldata_extract "0:art" 0x26800 0x20000
+               ath11k_remove_regdomain
+               ;;
        prpl,haze)
                caldata_extract_mmc "0:ART" 0x26800 0x20000
                ;;
index 3e81caf63f2e474f3029017db6db392c07f27704..26da7cd614efec30824f1be871f92b60a93f20cb 100755 (executable)
@@ -12,7 +12,8 @@ boot() {
        ;;
        linksys,mx4200v1|\
        linksys,mx4200v2|\
-       linksys,mx5300)
+       linksys,mx5300|\
+       linksys,mx8500)
                mtd resetbc s_env || true
        ;;
        esac
index b9668d0af4ef9f6d0521f11bc9cf856f0632e7d9..b99657fb4ccbd39b36b4568fee2dbd6daee96fdd 100644 (file)
@@ -77,7 +77,8 @@ platform_do_upgrade() {
                ;;
        linksys,mx4200v1|\
        linksys,mx4200v2|\
-       linksys,mx5300)
+       linksys,mx5300|\
+       linksys,mx8500)
                boot_part="$(fw_printenv -n boot_part)"
                if [ "$boot_part" -eq "1" ]; then
                        fw_setenv boot_part 2