openwrt/staging/mkresin.git
2 years agoipq806x: fix USB bug in 5.10 dtsi additions
Rodrigo Balerdi [Sat, 9 Apr 2022 21:26:17 +0000 (18:26 -0300)]
ipq806x: fix USB bug in 5.10 dtsi additions

The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.

This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148

This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.

Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.

It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agoipq806x: remove non-working fixes for USB bug in 5.10 dtsi additions
Rodrigo Balerdi [Sat, 9 Apr 2022 20:41:38 +0000 (17:41 -0300)]
ipq806x: remove non-working fixes for USB bug in 5.10 dtsi additions

These workarrounds are incomplete and non-functional, and thus not needed.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2 years agoath79: port HiWiFi HC6361 from ar71xx
Yousong Zhou [Sat, 16 Apr 2022 00:23:52 +0000 (00:23 +0000)]
ath79: port HiWiFi HC6361 from ar71xx

The device was added for ar71xx target and dropped during the ath79
transition, mainly because of the ascii mac address stored in bdinfo
partition

Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361

The vendor u-boot image accepts sysupgrade.bin image with specific
requirements, including having squashfs signature "hsqs" at file offset
0x140000.  This is not possible now that OpenWrt kernel image is at
least 2MB with the signature at offset 0x240000.

Installation of current build of OpenWrt now requires a bootstrap step
of installing an earlier version first.

 - If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE
   release should work
 - If the vendor u-boot accepts only verified flashsmt image, install
   the one in the above device page.  The image is based on Barrier
   Breaker

   SHA256SUM of the flashsmt image

81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156

After the bootstrap step, current build of OpenWrt can be installed
there fine.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agoath79: add nvmem cell mac-address-ascii support
Yousong Zhou [Fri, 8 Apr 2022 10:20:08 +0000 (10:20 +0000)]
ath79: add nvmem cell mac-address-ascii support

This is needed for devices with mac address stored in ascii format, e.g.
HiWiFi HC6361 to be ported in the following patch.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agoimage: strip metadata from images when used in other artifacts
Daniel Golle [Fri, 15 Apr 2022 12:25:41 +0000 (13:25 +0100)]
image: strip metadata from images when used in other artifacts

Image metadata and signature is of no use for images which are included
inside other artifacts (like an SD-card image). Strip them off before
using images in artifacts or stashing them for the ImageBuilder as the
contained signature breaks reproducibility.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoath79: cleanup mikrotik routerboot partitions
Thibaut VARÈNE [Thu, 31 Mar 2022 15:50:31 +0000 (17:50 +0200)]
ath79: cleanup mikrotik routerboot partitions

For some reason useless labels and aliases have been propagated through
copy-paste. Before the issue spreads any further, this patch cleans up
all relevant DTS files to the canonical form, bringing ath79 in line
with other mikrotik platforms (ramips and ipq40xx).

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2 years agoath79: add support for Yuncore A930
Thibaut VARÈNE [Thu, 14 Apr 2022 10:39:05 +0000 (12:39 +0200)]
ath79: add support for Yuncore A930

Specification:

- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2 years agomac80211 adjust QCA9561 PA bias
Thibaut VARÈNE [Thu, 14 Apr 2022 10:39:04 +0000 (12:39 +0200)]
mac80211 adjust QCA9561 PA bias

ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565
although they have the same radio IP-core, which results in a very low
output power and very low throughput as devices are further away from
the AP (compared to other 2.4GHz APs.)

In real life testing, without this patch the 2.4GHz throughput on Yuncore
XD3200 is around 10Mbps sitting close to the AP, and close to theoretical
maximum with the patch applied.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
[edit commit message]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2 years agoath79: add support for Yuncore XD3200
Thibaut VARÈNE [Thu, 14 Apr 2022 10:39:03 +0000 (12:39 +0200)]
ath79: add support for Yuncore XD3200

Specification:

- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)

LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2 years agobuild: target: improve UX of CONFIG_TARGET handling
Petr Štetiar [Tue, 29 Mar 2022 06:30:32 +0000 (08:30 +0200)]
build: target: improve UX of CONFIG_TARGET handling

Make it clear, that for `make kernel_{menu,old}config` it's possible to
use only following values for CONFIG_TARGET variable:

 * env
 * target
 * subtarget
 * subtarget_target

This should prevent misuse like `make kernel_menuconfig
CONFIG_TARGET=bcm2710` etc.

Keep support for obsolete `platform` and `subtarget_platform` targets
with deprecation notice so this compat stuff could be removed in the
future.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agokernel: usb-net-asix: fix 5.15 dependency
Petr Štetiar [Mon, 11 Apr 2022 15:39:23 +0000 (17:39 +0200)]
kernel: usb-net-asix: fix 5.15 dependency

Upstream in commit 34a1dee6bc44 ("net: usb: asix: ax88772: add generic
selftest support") in version 5.14 added dependency on generic selftest
functionality and armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-usb-net-asix is missing dependencies for the following libraries:
 mdio_devres.ko
 selftests.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: netdevices: add generic selftests module
Petr Štetiar [Mon, 11 Apr 2022 16:36:20 +0000 (18:36 +0200)]
kernel: netdevices: add generic selftests module

Upstream in commit 3e1e58d64c3d ("net: add generic selftest support") in
version 5.13 added generic selftests module and usb-net-asix already
depends on it, in version 5.18 via commit 1710b52d7c13 ("net: usb:
smsc95xx: add generic selftest support") it will be used by
usb-net-smsc95xx as well.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: usb-net-smsc95xx: fix 5.15 dependency
Petr Štetiar [Mon, 11 Apr 2022 15:36:55 +0000 (17:36 +0200)]
kernel: usb-net-smsc95xx: fix 5.15 dependency

armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-usb-net-smsc95xx is missing dependencies for the following libraries:
 libphy.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: mdio-devres: fix of-mdio dependency
Petr Štetiar [Mon, 11 Apr 2022 14:51:12 +0000 (16:51 +0200)]
kernel: mdio-devres: fix of-mdio dependency

armvirt/64 when compiled with ALL_KMODS=y reports following:

 Package kmod-mdio-devres is missing dependencies for the following libraries:
 of_mdio.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agokernel: of-mdio: fix 5.15 fwnode_mdio dependency
Petr Štetiar [Mon, 11 Apr 2022 11:45:33 +0000 (13:45 +0200)]
kernel: of-mdio: fix 5.15 fwnode_mdio dependency

Upstream in commit bc1bee3b87ee ("net: mdiobus: Introduce
fwnode_mdiobus_register_phy()") in version 5.14 introduced new
dependency:

 Package kmod-of-mdio is missing dependencies for the following libraries:

  fwnode_mdio.ko

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agomtools: update to version 4.0.39
Daniel Golle [Fri, 15 Apr 2022 00:15:26 +0000 (01:15 +0100)]
mtools: update to version 4.0.39

Improvements since the 4.0.38 release are:
 - Rename strtoi to strosi (string to signed int). The strtoi
   function on BSD does something else (returns an intmax, not
   an int)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoscripts/gen_image_generic.sh: fix order of files in EFI bootfs
Daniel Golle [Thu, 14 Apr 2022 23:46:28 +0000 (00:46 +0100)]
scripts/gen_image_generic.sh: fix order of files in EFI bootfs

mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate
over the directory entries, hence they end up in the FAT filesystem in
traversal order which breaks reproducibility (rather than being added
to the FAT filesystem in a reproducible order). Implement recursive
copy in gen_image_generic.sh in Shell code instead, as in that way we
can force files to be copied in reproducible order.

Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agogemini: Bump kernel to v5.15
Linus Walleij [Mon, 11 Apr 2022 21:46:19 +0000 (23:46 +0200)]
gemini: Bump kernel to v5.15

It's working well on all tested targets, so let's move
Gemini forward to v5.15. imx is already bumped so why not.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2 years agogemini: Create patches and config for kernel v5.15
Linus Walleij [Mon, 11 Apr 2022 21:46:18 +0000 (23:46 +0200)]
gemini: Create patches and config for kernel v5.15

This creates a v5.15 baseline for the Gemini platform.
The main new attraction is the new crypto driver from
Corentin Labbe that we activate in the new config.
Config was refreshed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2 years agogeneric: backport 5.16 RTL8366RB improvements
Linus Walleij [Mon, 11 Apr 2022 21:46:17 +0000 (23:46 +0200)]
generic: backport 5.16 RTL8366RB improvements

The prerequisite DSA changes for the nice RTL8366RB improvements
are already backported so bring back these changes as well.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2 years agourandom-seed: go back to seeding with shell script temporarily
Jason A. Donenfeld [Mon, 11 Apr 2022 22:53:49 +0000 (00:53 +0200)]
urandom-seed: go back to seeding with shell script temporarily

This reverts commit 2edc017a6e0cb92b72b768aaa46c6d336ad84eff.

We shouldn't be using a shell script here, but the SeedRNG integration
into OpenWRT requires a bit more thought. Etienne raised some important
points immediately after this was merged and planned to send some follow
up commits, but became busy with other things. The points he raised are
important enough that we should actually back this out until it's ready
to go, and then merge it as a cohesive unit. So let's revert this for
now, and come back to it later on.

Cc: Etienne Champetier <champetier.etienne@gmail.com>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2 years agomediatek: 5.15: re-enable arch timer on MT7623 as well
Daniel Golle [Thu, 14 Apr 2022 06:33:38 +0000 (07:33 +0100)]
mediatek: 5.15: re-enable arch timer on MT7623 as well

Re-enable arch timer also on MT7623, yet another time.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: 5.15: enable arm arch timer for mt7629
Chuanhong Guo [Sat, 9 Apr 2022 05:28:26 +0000 (13:28 +0800)]
mediatek: 5.15: enable arm arch timer for mt7629

otherwise the system delay is completely broken.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agokernel: 5.15: add support for ESMT F50x1G41LB
Chuanhong Guo [Thu, 14 Apr 2022 04:38:31 +0000 (12:38 +0800)]
kernel: 5.15: add support for ESMT F50x1G41LB

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agonetifd: relax check in dhcp proto handler
Daniel Golle [Wed, 13 Apr 2022 15:51:58 +0000 (16:51 +0100)]
netifd: relax check in dhcp proto handler

Checking whether /sbin/udhcpc is a symbolic link breaks using the
DHCP proto handler inside procd-ujail where bind-mounts are used for
the resolved link. Check whether /sbin/udhcpc is executable instead
to allow using the proto handler for DHCP-provisioned containers.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoprocd: update to git HEAD
Daniel Golle [Wed, 13 Apr 2022 15:47:07 +0000 (16:47 +0100)]
procd: update to git HEAD

 6343c3a procd: completely remove tmp-on-zram support
 5c5e63f uxc: fix potential NULL-pointer dereference
 eb03f03 jail: include necessary files for per-netns netifd instance

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomalta: add config-5.15
Daniel Golle [Wed, 13 Apr 2022 14:44:16 +0000 (15:44 +0100)]
malta: add config-5.15

Adding the kernel configuration has accidentally been omitted when
enabling testing kernel 5.15. Add it now.

Fixes: 09f6200198 ("malta: enable testing kernel 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobase-files: more robust sysupgrade on NAND
Daniel Golle [Wed, 13 Apr 2022 13:51:34 +0000 (14:51 +0100)]
base-files: more robust sysupgrade on NAND

Make sure sysupgrade on NAND also works in case of UBI volumes having
index >9. While at it, also make sure UBI device is detected and abort
in case it isn't. Use Shell built-in shorthand ':' instead of 'true'.

Fixes #9708
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agofirewall3: bump to latest git HEAD
Rui Salvaterra [Fri, 25 Feb 2022 13:54:36 +0000 (13:54 +0000)]
firewall3: bump to latest git HEAD

4cd7d4f Revert "firewall3: support table load on access on Linux 5.15+"
50979cc firewall3: remove unnecessary fw3_has_table

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agoath79: nand: add 5.15 support for nand subtarget
Koen Vandeputte [Wed, 13 Apr 2022 09:58:44 +0000 (11:58 +0200)]
ath79: nand: add 5.15 support for nand subtarget

Tested on GL.iNet E750

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: add missing symbols for 5.15
Koen Vandeputte [Wed, 6 Apr 2022 12:10:31 +0000 (14:10 +0200)]
kernel: add missing symbols for 5.15

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agonetfilter: move nf-log modules into separate packages
Jo-Philipp Wich [Tue, 12 Apr 2022 11:38:23 +0000 (13:38 +0200)]
netfilter: move nf-log modules into separate packages

Both legacy iptables and nftables require nf-log modules for rule logging,
so move them into a separate package both firewall implementations can
depend on.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agomac80211: backport minstrel_ht fix for legacy rates
Felix Fietkau [Tue, 12 Apr 2022 07:32:34 +0000 (09:32 +0200)]
mac80211: backport minstrel_ht fix for legacy rates

Fixes OFDM rates on 5 GHz

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agotoolchain: musl: Update to version 1.2.3
Hauke Mehrtens [Sun, 10 Apr 2022 22:11:51 +0000 (00:11 +0200)]
toolchain: musl: Update to version 1.2.3

Changes:
new features:
- qsort_r function (POSIX-future)
- pthread_getname_np extension function
- hard float on SPE FPU for powerpc-sf
- SEEK_DATA and SEEK_HOLE exposed in unistd.h (Linux extensions)

compatibility:
- free now preserves errno (POSIX-future requirement)
- setjmp is declared explicitly with returns_twice for non-GCC compilers
- macro version of isascii is no longer defined for C++
- dynamic linker now tolerates zero-length LOAD segments
- epoll_[p]wait is now a cancellation point
- pwd/grp functions no longer fail on systems without AF_UNIX support
- POSIX TZ parsing is stricter to allow more names to fallback to files
- NULL is now defined as nullptr when used in C++11 or later
- gettext now accepts null pointer as argument

bugs fixed:
- old regression in wcwidth of Hangul combining (vowel/final) letters
- duplocale used wrong malloc when malloc was replaced (1.2.2 regression)
- fmaf rounded wrong on archs without FE_TOWARDZERO (all softfloat archs)
- popen didn't honor requirement not to leak other popen pipe fds to child
- aligned_alloc and variants crashed on allocation failure
- dl_iterate_phdr reported incorrect module TLS pointers
- mishandling of some inputs in acoshf and expm1f and functions using them
- potentially wrong-sign zero in cproj functions at infinity
- multiple bugs in legacy function cuserid
- minor posix_spawn file actions API conformance issues
- pthread_setname_np fd leak
- out-of-bound read in zoneinfo handling with distant-past times
- out-of-tree builds lacked generated debug cfi for x86 asm

arch-specific bugs fixed:
- powerpc (32-bit) struct shmid_ds layout was wrong for some fields
- time64 struct layout was wrong in sound ioctl fallback (32-bit archs)

In addition it contains the following improvements:
* protect stack canary from leak via read-as-string by zeroing second byte
* fix excessively slow TLS performance on some mips models

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agonftables: add CONFLICT between versions
Eneas U de Queiroz [Thu, 7 Apr 2022 20:47:38 +0000 (17:47 -0300)]
nftables: add CONFLICT between versions

Have nftables-json conflict with nftables-nojson.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agowolfssl: bump to 5.2.0
Eneas U de Queiroz [Fri, 8 Apr 2022 13:27:25 +0000 (10:27 -0300)]
wolfssl: bump to 5.2.0

Fixes two high-severity vulnerabilities:

- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
  can be bypassed.  If a malicious client does not send the
  certificate_verify message a client can connect without presenting a
  certificate even if the server requires one.

- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
  v1.3 server can have its certificate heck bypassed. If the sig_algo in
  the certificate_verify message is different than the certificate
  message checking may be bypassed.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agomediatek/mt7622: enable accelerated crypto drivers
Eneas U de Queiroz [Thu, 31 Mar 2022 13:30:11 +0000 (10:30 -0300)]
mediatek/mt7622: enable accelerated crypto drivers

Use ARMv8 Crypto Extensions for AES, ghash and sha256.

This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoscripts/gen_image_generic.sh: generate reproducible EFI filesystem
Daniel Golle [Mon, 11 Apr 2022 14:25:27 +0000 (15:25 +0100)]
scripts/gen_image_generic.sh: generate reproducible EFI filesystem

Generate FAT filesystem for EFI boot in a reproducible way:
 * use '--invariant' option of mkfs.fat
 * set timestamps of all files to SOURCE_DATE_EPOCH
 * make sure files are ordered locale-independent

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomac80211: Update to version 5.15.33-1
Hauke Mehrtens [Tue, 5 Apr 2022 22:29:44 +0000 (00:29 +0200)]
mac80211: Update to version 5.15.33-1

This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.

This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoimagebuilder: export SOURCE_DATE_EPOCH to environment
Daniel Golle [Sat, 9 Apr 2022 23:55:21 +0000 (00:55 +0100)]
imagebuilder: export SOURCE_DATE_EPOCH to environment

Export SOURCE_DATE_EPOCH to environment so filesystem and image
creation tools will make use of it.
Fixes reproducibility of images generated with the ImageBuilder.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoarm-trusted-firmware-mediatek: remove no longer needed Configure step
Daniel Golle [Sat, 9 Apr 2022 21:04:58 +0000 (22:04 +0100)]
arm-trusted-firmware-mediatek: remove no longer needed Configure step

As anyway only the default is called now we can as well also just remove
the override for Build/Configure.

Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agotrusted-firmware-a.mk: make sure include directory exists
Daniel Golle [Sat, 9 Apr 2022 21:00:50 +0000 (22:00 +0100)]
trusted-firmware-a.mk: make sure include directory exists

ARM Trusted Firmware builds do not depend on any target libraries as
they are bare-metal builds. However, the compiler aborts due to
-Werror=missing-include-dirs if the include dir doesn't exists and this
can happen when building with parallelisation as that makes it likely
for arm-trusted-firmware-* to be build very early before any of the
libraries which would implicitely create the directory.
Fix this by making sure the include dir exists before building.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agokernel: bump 5.10 to 5.10.110
John Audia [Fri, 8 Apr 2022 16:35:54 +0000 (12:35 -0400)]
kernel: bump 5.10 to 5.10.110

Removed upstreamed:
  generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch
  generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch
  ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Compile-/run-tested: ath79/generic (Archer C7 v2).

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agokernel: bump 5.15 to 5.15.33
Rui Salvaterra [Fri, 8 Apr 2022 13:43:04 +0000 (14:43 +0100)]
kernel: bump 5.15 to 5.15.33

Deleted (upstreamed):
generic/backport-5.15/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch [1]
generic/backport-5.15/730-v5.16-hv-utils-add-PTP_1588_CLOCK-to-Kconfig-to-fix-build.patch [2]
generic/pending-5.15/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch [3]
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch [4]

Manually rebased:
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch
ramips/patches-5.15/710-at803x.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d29cda15cab086d82d692de016f7249545d4b6b4
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=ed750e22e44366e264bcdf7b1cf0713f08f7980a
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=0fe94b84c43cfea867e1721606185e8686d7d32f

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Refresh patches again]
[Remove generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agokernel: bump 5.15 to 5.15.32
Rui Salvaterra [Wed, 30 Mar 2022 08:42:31 +0000 (09:42 +0100)]
kernel: bump 5.15 to 5.15.32

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agokernel: move some symbols to generic config
Aleksander Jan Bajkowski [Sun, 27 Mar 2022 16:55:48 +0000 (18:55 +0200)]
kernel: move some symbols to generic config

This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.

The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.

The other symbols are disabled and should be in the generic config.

This commit also removes these symbols from subtargets.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agogeneric: 5.15: fix aardvak pci pending patch
Ansuel Smith [Wed, 30 Mar 2022 14:14:03 +0000 (16:14 +0200)]
generic: 5.15: fix aardvak pci pending patch

Fix aardvak pci controller pending patch. Use generic_handle_domain_irq
and fix rebase error.

Fixes: 483503603cb2 ("generic: 5.15: rework pending patch")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2 years agoarmvirt: add 5.15 as testing kernel
Aleksander Jan Bajkowski [Mon, 21 Mar 2022 18:09:32 +0000 (19:09 +0100)]
armvirt: add 5.15 as testing kernel

Add 5.15 as testing kernel.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agoarmvirt: move common symbols from subtarget to target config
Aleksander Jan Bajkowski [Sat, 2 Apr 2022 13:01:40 +0000 (15:01 +0200)]
armvirt: move common symbols from subtarget to target config

These new symbols are common for all subtargets and
can be moved into target config.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agoarmvirt: refresh 5.15 config
Aleksander Jan Bajkowski [Mon, 21 Mar 2022 18:43:20 +0000 (19:43 +0100)]
armvirt: refresh 5.15 config

This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agoarmvirt: copy config files from 5.10
Aleksander Jan Bajkowski [Mon, 21 Mar 2022 21:14:54 +0000 (22:14 +0100)]
armvirt: copy config files from 5.10

Copy config files from 5.10.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agoarmvirt: refresh 5.10 config
Aleksander Jan Bajkowski [Mon, 21 Mar 2022 21:01:42 +0000 (22:01 +0100)]
armvirt: refresh 5.10 config

This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2 years agoipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17
Ray Wang [Mon, 4 Apr 2022 02:29:18 +0000 (10:29 +0800)]
ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17

RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5.

Signed-off-by: Ray Wang <raywang777@foxmail.com>
2 years agoath79: Move TPLink WPA8630Pv2 to ath79-tiny target
Joe Mullally [Mon, 30 Aug 2021 21:35:05 +0000 (22:35 +0100)]
ath79: Move TPLink WPA8630Pv2 to ath79-tiny target

These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.

Note for users sysupgrading from the previous ath79-generic snapshot
images:

The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.

To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".

If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:

* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
2 years agomwlwifi: fix 5.15 kernel support
Robert Marko [Wed, 30 Mar 2022 18:23:19 +0000 (20:23 +0200)]
mwlwifi: fix 5.15 kernel support

Fix compilation and usage under kernel 5.15 for the mwlwifi driver.

For detailed description of changes, check individual patches.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2 years agodropbear: bump to 2022.82
Konstantin Demin [Thu, 7 Apr 2022 08:33:08 +0000 (11:33 +0300)]
dropbear: bump to 2022.82

- update dropbear to latest stable 2022.82;
  for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- use $(AUTORELEASE) in PKG_RELEASE
- use https for all uris
- refresh all patches
- rewrite patches:
  - 100-pubkey_path.patch
  - 130-ssh_ignore_x_args.patch

binary/pkg size changes:
- ath79/generic, mips:
  - binary: 215112 -> 219228 (+4116)
  - pkg: 111914 -> 113404 (+1490)
- ath79/tiny, mips:
  - binary: 172501 -> 172485 (-16)
  - pkg: 89871 -> 90904 (+1033)

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
2 years agolibmnl: update to 1.0.5
Nick Hainke [Tue, 5 Apr 2022 13:01:43 +0000 (15:01 +0200)]
libmnl: update to 1.0.5

Changes:

Duncan Roe (5):
      nlmsg: Fix a missing doxygen section trailer
      build: doc: "make" builds & installs a full set of man pages
      build: doc: get rid of the need for manual updating of Makefile
      build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
      src: doc: Fix messed-up Netlink message batch diagram

Fernando Fernandez Mancera (1):
      src: fix doxygen function documentation

Florian Westphal (1):
      libmnl: zero attribute padding

Guillaume Nault (1):
      callback: mark cb_ctl_array 'const' in mnl_cb_run2()

Kylie McClain (1):
      examples: nfct-daemon: Fix test building on musl libc

Laura Garcia Liebana (4):
      examples: add arp cache dump example
      examples: fix neigh max attributes
      examples: fix print line format
      examples: reduce LOCs during neigh attributes validation

Pablo Neira Ayuso (3):
      doxygen: remove EXPORT_SYMBOL from the output
      include: add MNL_SOCKET_DUMP_SIZE definition
      build: libmnl 1.0.5 release

Petr Vorel (1):
      examples: Add rtnl-addr-add.c

Stephen Hemminger (1):
      examples: rtnl-addr-dump: fix typo

igo95862 (1):
      doxygen: Fixed link to the git source tree on the website.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2 years agolibnfnetlink: update to 1.0.2
Nick Hainke [Tue, 5 Apr 2022 13:26:24 +0000 (15:26 +0200)]
libnfnetlink: update to 1.0.2

Changes:

c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings

Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2 years agogpio-button-hotplug: fix data race
Andrey Erokhin [Wed, 6 Apr 2022 09:36:15 +0000 (12:36 +0300)]
gpio-button-hotplug: fix data race

bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer

Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
2 years agotools/meson: update to 0.61.4
Rosen Penev [Wed, 16 Mar 2022 23:18:07 +0000 (16:18 -0700)]
tools/meson: update to 0.61.4

Override python to use the one in host instead of hostpkg. There's no
need to use the latter.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agotools/cmake: fix download url
leo chung [Thu, 31 Mar 2022 02:58:29 +0000 (10:58 +0800)]
tools/cmake: fix download url

fix the cmake.org download url

Signed-off-by: leo chung <gewalalb@gmail.com>
2 years agokernel: Fix oob layout of XTX XT26G0xA
Felix Matouschek [Fri, 8 Apr 2022 16:27:05 +0000 (18:27 +0200)]
kernel: Fix oob layout of XTX XT26G0xA

The correct oob layout is:

ECC:
region->offset = 48;
region->length = 16;

Free:
/* Reserve 1 byte for the BBM. */
region->offset = 1;
region->length = 47;

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2 years agokernel: Fix readid method of XTX XT26G0xA
Felix Matouschek [Fri, 8 Apr 2022 16:33:10 +0000 (18:33 +0200)]
kernel: Fix readid method of XTX XT26G0xA

The correct readid method is SPINAND_READID_METHOD_OPCODE_ADDR.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2 years agokernel: mtk_bmt: skip bitflip check if threshold isn't set
Chuanhong Guo [Thu, 7 Apr 2022 01:56:02 +0000 (09:56 +0800)]
kernel: mtk_bmt: skip bitflip check if threshold isn't set

kernel spi-nand driver leaves this field empty and let mtd set it later.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agokernel: v5.10: backport GigaDevice SPI-NAND supports
Chuanhong Guo [Sat, 9 Apr 2022 13:01:46 +0000 (21:01 +0800)]
kernel: v5.10: backport GigaDevice SPI-NAND supports

This backports GD SPI NAND support from nand/next to v5.10

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agokernel: v5.15: backport GigaDevice SPI-NAND supports
Chuanhong Guo [Sat, 9 Apr 2022 12:22:36 +0000 (20:22 +0800)]
kernel: v5.15: backport GigaDevice SPI-NAND supports

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2 years agoqosify: update to the latest version
Felix Fietkau [Fri, 8 Apr 2022 11:07:36 +0000 (13:07 +0200)]
qosify: update to the latest version

92f5e18675bf interface: fix ifname present check in interface status
ef82defaae26 ubus: add active devices to bridger blacklist

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobcm53xx: refresh kernel 5.15 config
Rafał Miłecki [Fri, 8 Apr 2022 08:49:31 +0000 (10:49 +0200)]
bcm53xx: refresh kernel 5.15 config

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agofirewall4: update to latest Git HEAD
Jo-Philipp Wich [Tue, 22 Mar 2022 20:09:27 +0000 (21:09 +0100)]
firewall4: update to latest Git HEAD

a378883 fw4: fix emitting family specific redirect rules without any addrs
11feddf fw4: bracketize IPv6 addresses in dnat addr:port notation
9972f7d fw4: ensure to capitalize weekday names
fde8070 treewide: forward compatibility changes

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agoucode: update to latest Git HEAD
Jo-Philipp Wich [Tue, 22 Mar 2022 19:26:59 +0000 (20:26 +0100)]
ucode: update to latest Git HEAD

33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agohostapd: add ubus link-measurements notifications
David Bauer [Thu, 31 Mar 2022 20:39:04 +0000 (22:39 +0200)]
hostapd: add ubus link-measurements notifications

Notify external ubus subscribers of received link-measurement reports.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agohostapd: add ubus method for requesting link measurements
David Bauer [Tue, 29 Mar 2022 22:31:26 +0000 (00:31 +0200)]
hostapd: add ubus method for requesting link measurements

Add a ubus method to request link-measurements from connected STAs.

In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agohostapd: add support for enabling link measurements
David Bauer [Thu, 31 Mar 2022 16:06:02 +0000 (18:06 +0200)]
hostapd: add support for enabling link measurements

Allow external processes to enable advertisement of link-measurement RRM
capability.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agoat91: Automatically detect USB feature
Hauke Mehrtens [Wed, 6 Apr 2022 22:36:25 +0000 (00:36 +0200)]
at91: Automatically detect USB feature

The sama7 sub target does not have USB support, the feature should not
be activated there. OpenWrt can automatically detect if the target
supports USB by using the scripts/target-metadata.pl script. With the
automatic detection USB support will only get activated on subtargest
which actually support USB like sam9x and sama5.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Do not build in Bluetooth
Hauke Mehrtens [Tue, 5 Apr 2022 20:28:30 +0000 (22:28 +0200)]
at91/sama7: Do not build in Bluetooth

Bluetooth should be activated as an optional kmod package instead of
compiling it into the kernel.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Use ext4 driver for ext2 and ext3
Hauke Mehrtens [Tue, 5 Apr 2022 20:27:41 +0000 (22:27 +0200)]
at91/sama7: Use ext4 driver for ext2 and ext3

Use the ext4 driver for ext2 and ext3 too. This feature is activated in
the OpenWrt generic configuration.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Deactivate certification and key system
Hauke Mehrtens [Tue, 5 Apr 2022 20:24:00 +0000 (22:24 +0200)]
at91/sama7: Deactivate certification and key system

This was probably activated by mac80211 which was activated before.
mac80211 is build from backports in OpenWrt.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Do not activate cgroups and namespaces
Hauke Mehrtens [Tue, 5 Apr 2022 20:22:04 +0000 (22:22 +0200)]
at91/sama7: Do not activate cgroups and namespaces

cgroups and namespaces should be configured by the generic OpenWrt
configuration and not for a specific target.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoat91/sama7: Remove config options build as module
Hauke Mehrtens [Tue, 5 Apr 2022 20:14:16 +0000 (22:14 +0200)]
at91/sama7: Remove config options build as module

Remove the configuration options which are building modules for the sub
target configuration.

These kernel modules are not packaged. Kernel options should only be
build as a module when they are selected by a kmod package and not by
setting them to =m in the target kernel configuration.

Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agokernel: remove duplicate patch that is already in the 5.15 kernel tree
Felix Fietkau [Thu, 7 Apr 2022 11:07:30 +0000 (13:07 +0200)]
kernel: remove duplicate patch that is already in the 5.15 kernel tree

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agomt76: update to the latest version
Felix Fietkau [Thu, 7 Apr 2022 10:23:52 +0000 (12:23 +0200)]
mt76: update to the latest version

5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoubox: add example /etc/modules.conf + conffiles entry
Felix Fietkau [Thu, 7 Apr 2022 10:01:44 +0000 (12:01 +0200)]
ubox: add example /etc/modules.conf + conffiles entry

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobcm27xx: include 'rtc' in target's 'FEATURES'
Piotr Dymacz [Wed, 6 Apr 2022 21:07:55 +0000 (23:07 +0200)]
bcm27xx: include 'rtc' in target's 'FEATURES'

There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.

Fixes: #9594
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agouboot-imx: build 'u-boot-dtb.img' for SolidRun CuBox-i
Piotr Dymacz [Fri, 1 Apr 2022 13:11:37 +0000 (15:11 +0200)]
uboot-imx: build 'u-boot-dtb.img' for SolidRun CuBox-i

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoimx: image: use 'u-boot-dtb.img' filename for SPL payload
Piotr Dymacz [Fri, 1 Apr 2022 13:11:36 +0000 (15:11 +0200)]
imx: image: use 'u-boot-dtb.img' filename for SPL payload

For targets in U-Boot which were migrated to DM, the correct binary
image filename will be 'u-boot-dtb.img'. For backward compatibility,
keep support for both files and use the one which was generated with
our 'uboot-imx' package.

See also 'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' and 'CONFIG_OF_CONTROL' in
mainline U-Boot sources.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoimx: bootscript-apalis: make it working with U-Boot 2022.01
Petr Štetiar [Fri, 1 Apr 2022 13:11:35 +0000 (15:11 +0200)]
imx: bootscript-apalis: make it working with U-Boot 2022.01

Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[pepe2k@gmail.com: updated commit title for 2022.01]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agouboot-imx: bump to 2022.01 release
Piotr Dymacz [Fri, 1 Apr 2022 13:11:34 +0000 (15:11 +0200)]
uboot-imx: bump to 2022.01 release

Two patches were removed because of the changes introduced in upstream:

1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").

2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agokernel: add missing CONFIG_SECURITY_LANDLOCK symbol for 5.15
Daniel Golle [Wed, 6 Apr 2022 19:04:22 +0000 (20:04 +0100)]
kernel: add missing CONFIG_SECURITY_LANDLOCK symbol for 5.15

Building with SELinux enabled unveiled a missing Kconfig symbol.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agolibselinux: add missing host-build dependency on libsepol/host
Daniel Golle [Wed, 6 Apr 2022 18:59:52 +0000 (19:59 +0100)]
libselinux: add missing host-build dependency on libsepol/host

The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoscripts: make sure sort-order is independent from locale
Daniel Golle [Wed, 6 Apr 2022 16:25:16 +0000 (17:25 +0100)]
scripts: make sure sort-order is independent from locale

Set LC_ALL=C environment variable when calling 'sort' as the sort
order otherwise depends on the locale set.

Fixes: 56ce110b73 ("scripts: make sure conffiles are sorted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agodnsmasq: add procd interface index tracking
Valentyn Datsko [Wed, 6 Apr 2022 13:13:13 +0000 (16:13 +0300)]
dnsmasq: add procd interface index tracking

Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.

Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobridger: add bridge forwarding accelerator
Felix Fietkau [Wed, 6 Apr 2022 12:09:34 +0000 (14:09 +0200)]
bridger: add bridge forwarding accelerator

This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: set SOURCE_DATE_EPOCH for initramfs root dir
Daniel Golle [Wed, 6 Apr 2022 11:19:31 +0000 (12:19 +0100)]
kernel: set SOURCE_DATE_EPOCH for initramfs root dir

Make sure the timestamp of the root directory of the initramfs is set
to SOURCE_DATE_EPOCH as well.

Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoqosify: update to the latest version
Felix Fietkau [Tue, 5 Apr 2022 19:27:40 +0000 (21:27 +0200)]
qosify: update to the latest version

Replace the tc-full dependency with tc + libnl-tiny

1cd5e12eecdc loader/interface: attach bpf program directly using netlink

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoubox: update to the latest version
Felix Fietkau [Tue, 5 Apr 2022 15:32:40 +0000 (17:32 +0200)]
ubox: update to the latest version

b87a4fdca634 kmodloader: support loading module options and blacklist from /etc/modules.conf

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: package mhi mbim driver
Koen Vandeputte [Tue, 5 Apr 2022 13:07:36 +0000 (15:07 +0200)]
kernel: package mhi mbim driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi wwan ctrl driver
Koen Vandeputte [Tue, 5 Apr 2022 13:05:02 +0000 (15:05 +0200)]
kernel: package mhi wwan ctrl driver

MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi network driver
Koen Vandeputte [Fri, 1 Apr 2022 08:50:46 +0000 (10:50 +0200)]
kernel: package mhi network driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi pci driver
Koen Vandeputte [Tue, 5 Apr 2022 12:53:01 +0000 (14:53 +0200)]
kernel: package mhi pci driver

This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 years agokernel: package mhi bus driver
Koen Vandeputte [Fri, 1 Apr 2022 08:50:25 +0000 (10:50 +0200)]
kernel: package mhi bus driver

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>