include/ns16550.h

   1 /*
   2  * NS16550 Serial Port
   3  * originally from linux source (arch/powerpc/boot/ns16550.h)
   4  *
   5  * Cleanup and unification
   6  * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
   7  *
   8  * modified slightly to
   9  * have addresses as offsets from CONFIG_SYS_ISA_BASE
  10  * added a few more definitions
  11  * added prototypes for ns16550.c
  12  * reduced no of com ports to 2
  13  * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
  14  *
  15  * added support for port on 64-bit bus
  16  * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
  17  */
  18
  19 /*
  20  * Note that the following macro magic uses the fact that the compiler
  21  * will not allocate storage for arrays of size 0
  22  */
  23
  24 #include <linux/types.h>
  25
  26 #ifdef CONFIG_DM_SERIAL
  27 /*
  28  * For driver model we always use one byte per register, and sort out the
  29  * differences in the driver
  30  */
  31 #define CONFIG_SYS_NS16550_REG_SIZE (-1)
  32 #endif
  33
  34 #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
  35 #error "Please define NS16550 registers size."
  36 #elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
  37 #define UART_REG(x) u32 x
  38 #elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
  39 #define UART_REG(x)                                                \
  40         unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
  41         unsigned char x;
  42 #elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
  43 #define UART_REG(x)                                                     \
  44         unsigned char x;                                                \
  45         unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
  46 #endif
  47
  48 /**
  49  * struct ns16550_platdata - information about a NS16550 port
  50  *
  51  * @base:               Base register address
  52  * @reg_width:          IO accesses size of registers (in bytes)
  53  * @reg_shift:          Shift size of registers (0=byte, 1=16bit, 2=32bit...)
  54  * @clock:              UART base clock speed in Hz
  55  */
  56 struct ns16550_platdata {
  57         unsigned long base;
  58         int reg_width;
  59         int reg_shift;
  60         int reg_offset;
  61         int clock;
  62         u32 fcr;
  63 };
  64
  65 struct udevice;
  66
  67 struct NS16550 {
  68         UART_REG(rbr);          /* 0 */
  69         UART_REG(ier);          /* 1 */
  70         UART_REG(fcr);          /* 2 */
  71         UART_REG(lcr);          /* 3 */
  72         UART_REG(mcr);          /* 4 */
  73         UART_REG(lsr);          /* 5 */
  74         UART_REG(msr);          /* 6 */
  75         UART_REG(spr);          /* 7 */
  76 #ifdef CONFIG_SOC_DA8XX
  77         UART_REG(reg8);         /* 8 */
  78         UART_REG(reg9);         /* 9 */
  79         UART_REG(revid1);       /* A */
  80         UART_REG(revid2);       /* B */
  81         UART_REG(pwr_mgmt);     /* C */
  82         UART_REG(mdr1);         /* D */
  83 #else
  84         UART_REG(mdr1);         /* 8 */
  85         UART_REG(reg9);         /* 9 */
  86         UART_REG(regA);         /* A */
  87         UART_REG(regB);         /* B */
  88         UART_REG(regC);         /* C */
  89         UART_REG(regD);         /* D */
  90         UART_REG(regE);         /* E */
  91         UART_REG(uasr);         /* F */
  92         UART_REG(scr);          /* 10*/
  93         UART_REG(ssr);          /* 11*/
  94 #endif
  95 #ifdef CONFIG_DM_SERIAL
  96         struct ns16550_platdata *plat;
  97 #endif
  98 };
  99
 100 #define thr rbr
 101 #define iir fcr
 102 #define dll rbr
 103 #define dlm ier
 104
 105 typedef struct NS16550 *NS16550_t;
 106
 107 /*
 108  * These are the definitions for the FIFO Control Register
 109  */
 110 #define UART_FCR_FIFO_EN        0x01 /* Fifo enable */
 111 #define UART_FCR_CLEAR_RCVR     0x02 /* Clear the RCVR FIFO */
 112 #define UART_FCR_CLEAR_XMIT     0x04 /* Clear the XMIT FIFO */
 113 #define UART_FCR_DMA_SELECT     0x08 /* For DMA applications */
 114 #define UART_FCR_TRIGGER_MASK   0xC0 /* Mask for the FIFO trigger range */
 115 #define UART_FCR_TRIGGER_1      0x00 /* Mask for trigger set at 1 */
 116 #define UART_FCR_TRIGGER_4      0x40 /* Mask for trigger set at 4 */
 117 #define UART_FCR_TRIGGER_8      0x80 /* Mask for trigger set at 8 */
 118 #define UART_FCR_TRIGGER_14     0xC0 /* Mask for trigger set at 14 */
 119
 120 #define UART_FCR_RXSR           0x02 /* Receiver soft reset */
 121 #define UART_FCR_TXSR           0x04 /* Transmitter soft reset */
 122
 123 /* Ingenic JZ47xx specific UART-enable bit. */
 124 #define UART_FCR_UME            0x10
 125
 126 /* Clear & enable FIFOs */
 127 #define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \
 128                         UART_FCR_RXSR | \
 129                         UART_FCR_TXSR)
 130
 131 /*
 132  * These are the definitions for the Modem Control Register
 133  */
 134 #define UART_MCR_DTR    0x01            /* DTR   */
 135 #define UART_MCR_RTS    0x02            /* RTS   */
 136 #define UART_MCR_OUT1   0x04            /* Out 1 */
 137 #define UART_MCR_OUT2   0x08            /* Out 2 */
 138 #define UART_MCR_LOOP   0x10            /* Enable loopback test mode */
 139 #define UART_MCR_AFE    0x20            /* Enable auto-RTS/CTS */
 140
 141 #define UART_MCR_DMA_EN 0x04
 142 #define UART_MCR_TX_DFR 0x08
 143
 144 /*
 145  * These are the definitions for the Line Control Register
 146  *
 147  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 148  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 149  */
 150 #define UART_LCR_WLS_MSK 0x03           /* character length select mask */
 151 #define UART_LCR_WLS_5  0x00            /* 5 bit character length */
 152 #define UART_LCR_WLS_6  0x01            /* 6 bit character length */
 153 #define UART_LCR_WLS_7  0x02            /* 7 bit character length */
 154 #define UART_LCR_WLS_8  0x03            /* 8 bit character length */
 155 #define UART_LCR_STB    0x04            /* # stop Bits, off=1, on=1.5 or 2) */
 156 #define UART_LCR_PEN    0x08            /* Parity eneble */
 157 #define UART_LCR_EPS    0x10            /* Even Parity Select */
 158 #define UART_LCR_STKP   0x20            /* Stick Parity */
 159 #define UART_LCR_SBRK   0x40            /* Set Break */
 160 #define UART_LCR_BKSE   0x80            /* Bank select enable */
 161 #define UART_LCR_DLAB   0x80            /* Divisor latch access bit */
 162
 163 /*
 164  * These are the definitions for the Line Status Register
 165  */
 166 #define UART_LSR_DR     0x01            /* Data ready */
 167 #define UART_LSR_OE     0x02            /* Overrun */
 168 #define UART_LSR_PE     0x04            /* Parity error */
 169 #define UART_LSR_FE     0x08            /* Framing error */
 170 #define UART_LSR_BI     0x10            /* Break */
 171 #define UART_LSR_THRE   0x20            /* Xmit holding register empty */
 172 #define UART_LSR_TEMT   0x40            /* Xmitter empty */
 173 #define UART_LSR_ERR    0x80            /* Error */
 174
 175 #define UART_MSR_DCD    0x80            /* Data Carrier Detect */
 176 #define UART_MSR_RI     0x40            /* Ring Indicator */
 177 #define UART_MSR_DSR    0x20            /* Data Set Ready */
 178 #define UART_MSR_CTS    0x10            /* Clear to Send */
 179 #define UART_MSR_DDCD   0x08            /* Delta DCD */
 180 #define UART_MSR_TERI   0x04            /* Trailing edge ring indicator */
 181 #define UART_MSR_DDSR   0x02            /* Delta DSR */
 182 #define UART_MSR_DCTS   0x01            /* Delta CTS */
 183
 184 /*
 185  * These are the definitions for the Interrupt Identification Register
 186  */
 187 #define UART_IIR_NO_INT 0x01    /* No interrupts pending */
 188 #define UART_IIR_ID     0x06    /* Mask for the interrupt ID */
 189
 190 #define UART_IIR_MSI    0x00    /* Modem status interrupt */
 191 #define UART_IIR_THRI   0x02    /* Transmitter holding register empty */
 192 #define UART_IIR_RDI    0x04    /* Receiver data interrupt */
 193 #define UART_IIR_RLSI   0x06    /* Receiver line status interrupt */
 194
 195 /*
 196  * These are the definitions for the Interrupt Enable Register
 197  */
 198 #define UART_IER_MSI    0x08    /* Enable Modem status interrupt */
 199 #define UART_IER_RLSI   0x04    /* Enable receiver line status interrupt */
 200 #define UART_IER_THRI   0x02    /* Enable Transmitter holding register int. */
 201 #define UART_IER_RDI    0x01    /* Enable receiver data interrupt */
 202
 203 /* useful defaults for LCR */
 204 #define UART_LCR_8N1    0x03
 205
 206 void NS16550_init(NS16550_t com_port, int baud_divisor);
 207 void NS16550_putc(NS16550_t com_port, char c);
 208 char NS16550_getc(NS16550_t com_port);
 209 int NS16550_tstc(NS16550_t com_port);
 210 void NS16550_reinit(NS16550_t com_port, int baud_divisor);
 211
 212 /**
 213  * ns16550_calc_divisor() - calculate the divisor given clock and baud rate
 214  *
 215  * Given the UART input clock and required baudrate, calculate the divisor
 216  * that should be used.
 217  *
 218  * @port:       UART port
 219  * @clock:      UART input clock speed in Hz
 220  * @baudrate:   Required baud rate
 221  * @return baud rate divisor that should be used
 222  */
 223 int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate);
 224
 225 /**
 226  * ns16550_serial_ofdata_to_platdata() - convert DT to platform data
 227  *
 228  * Decode a device tree node for an ns16550 device. This includes the
 229  * register base address and register shift properties. The caller must set
 230  * up the clock frequency.
 231  *
 232  * @dev:        dev to decode platform data for
 233  * @return:     0 if OK, -EINVAL on error
 234  */
 235 int ns16550_serial_ofdata_to_platdata(struct udevice *dev);
 236
 237 /**
 238  * ns16550_serial_probe() - probe a serial port
 239  *
 240  * This sets up the serial port ready for use, except for the baud rate
 241  * @return 0, or -ve on error
 242  */
 243 int ns16550_serial_probe(struct udevice *dev);
 244
 245 /**
 246  * struct ns16550_serial_ops - ns16550 serial operations
 247  *
 248  * These should be used by the client driver for the driver's 'ops' member
 249  */
 250 extern const struct dm_serial_ops ns16550_serial_ops;